B10F/B10F-PG/B15F/B15F-PG Mixer Parts List

ELECTRIC DIAGRAM
PE2

MANUAL INSTRUCTION
N L

K1 MIXER BAKERY / PLANETARY MIXER B10F

K2 K3 K4 K0

C
1C

K1 overload protection switch

1C AC contact device
K2 bowl lift switch
K3 safety protect switch
K4 urgency stop switch
K5 switch
K reacor
K0 start switch
CA capacitor
M
M motor

K5 CA

14
 B10F/B10F-PG/B15F/B15F-PG Mixer Parts List
INDEX TROUBLE SHOOTING AND SPECIFICTION
TROUBLE SHOOTING
PARTS CATALOG OVERVIEW 1 Trouble Possible Causes Re-cover
The axle can't work when operate Poor contact of the electrical equi-
the machine. pment. Check the plug.
FIGURE 1 TRANSMISSION CASE, ARM, STAND 2
The mixing bowl out of position. Moving direction is not correct.
FIGURE 2 AXLE 3 Leak oil. Sealing washer is damaged. Change.
Defficult to move the bowl up and Slideway is rusted. Clean the slideway and lubrication.
down.
FIGURE 3 GEAR AXLE 4
The motor is overheat and speed The voltage is not enough, or inco- Check the voltage or use lower s-
down. rrect speed. peed.
FIGURE 4 MOTOR UNIT 5 Noise and over heat. Poor lubrication. Add or change lubrication.
Mixer touch the bowl. The mixing device or bowl deform- Repair or change the bowl or mixi-
FIGURE 5 FORK AND SPEED SHAFT 6 ed. ng device.
FIGURE 6 ARM AND HANDWHEEL TYPEBOWL LIFTER UINT 7
SPECIFICTION
FIGURE 7 HANDGRIP BOWL LIFTER UNIT 8 Type B10F B10F B10F-PG B10F-PG B15F B15F B15F-PG B15F-PG
FIGURE 8 TURNING PLATE AND MIXING AXLE 9 Mixer L 10 10 10 10 15 15 15 15
Power Supply V 110V 220~240V 110V 220~240V 110V 220~240V 110V 220~240V
FIGURE 9 STANDARD ACCESSORIES 10
Input Power W 600 600 600 600 600 600 600 600
OPERATION INSTRUCTION 11 508 480 508 480 508 480 508 480
Mixing
Speed 258 244 258 244 258 244 258 244
WARNING AND SPECIALATTENTION 12 r.p.m
156 148 156 148 156 148 156 148
TROUBLE SHOOTING AND SPECIFICTION 13 Maxflour Capacity(kg) 2.5 2.5 2.5 2.5 3.5 3.5 3.5 3.5
ELECTRIC DIAGRAM 14
13
B10F/B10F-PG/B15F/B15F-PG Mixer Parts List B10F/B10F-PG/B15F/B15F-PG Mixer Parts List

WARNING AND SPECIAL ATTENTION PARTS CATALOG

WARNING OVERVIEW
1 DON'T USE WATER PIPE TO WASH THE MIXER DIRECTLY;
2 PLEASE PULL OFF THE PLUG BEFORE MAINTAINNING, AND MAKE IT
MAINTAINED BY PROFESSIONALS;
2
3 DON'T TOUCH THE SWITCHSAND PLUG WITH WET HAND; 3
Item Descviption

4 IF BROKEN, PLEASE STOP USINGAT ONCE 1 french

2 rear cover
5 THERE ISAGROUNDED NUT (SIGNED " ") IN THE MACHINE, PLEASE 1
4 3 ring
RECOVER IT TO ORIGIN CONDITION, DON'T CANCELTHE GROUNDED LINE;
4 Mixing device III
6 DON'T PUT HANDS INTO THE BOWL OR TOUCH THE MIXING DEVICES WH- 5 bowl
EN WORKING;
7 DON'TALLOW THE MINOR CLOSE TO THE MACHINE;
5
8 THE MACHINE SHOULD BE FIXED ON THE DRYWOODEN SPLINTAND WO-
RK IN SAFEAREA;
9 IF THE ELECTRICALWIRE IS BROKEN, PLEASE CHANGE IT BY PROFECTIO-
NALS.
NOTES:
SPECIAL ATTENTION The no using pipe line sprays to wash
the mixer
1 BEFORE USING , PLEASE CLEAN THE BOWLAND THE MIXING DEVICES CAR-
EFULLY,AND THEN INSTALLTHE BOWL ONTO THE MACHINE CORRECTLY Wet hand in no using contact switch
AND TIGHTLY; with power supply plug.
2 WHEN CHOOSING MIXING DEVICES, PLEASE REFER TO THE OPERATION MA-
While maintaining the mixer, must pull
NUALTO CHOSE THE CORRECT SPEED, OR IT WILL DESTORYTHE INSIDE SPA-
out first the power supply plug, and from
RE PARTSAND SHORTEN THE USING LIFE OF THE MACHIE;
profession the personnel maintains.
3 AFTER USING, PLEASE POWER OFF THE MACHINE,AND PUT THE BOWLAND
DEVICES IN THE SAFEAND CLEAN PLACEAFTER CLEANING;
4 KEEP ENVIROMENTARROUND THE MACHINE DRY HEALTHAND SAFE.

12 1
B10F/B10F-PG/B15F/B15F-PG Mixer Parts List B10F/B10F-PG/B15F/B15F-PG Mixer Parts List
Figure 1 TRANSMISSION CASE, ARM, STAND OPERATION INSTRUCTION
Item Descviption Qty
1 1 screw M5*35 1
110V
2 cover 1 Before using, please check power supply if it match
2 220~240V
3 plate 1
your machine and be sure ground wire is eliable.
4 screw M5*12 5
4
3 4 bearing 6202 1
5
5 6 1
6 bearing 6201 Before testing, please take mixing device off first, in
10 11
7 bearing cover 1
8 9 order to avoid damage machine which is match mo-
13
8 screw M5*20 4
7
ving direction. It's necessary to change the three-ph-
12 9 body 1
ase machine if the moving direction is not match wi-
10 rear cover 1
th arrow.
11 screw M6*55 4
12 breeze window 1
13 screw M5*12 1 For changing the speed: Please stop machine first
20 14 arm 1 before change speed in order to aviod damage gear
15 15 stand 1
OFF box.
19
14 16 16 capacitor board 1
17 capacitor 1
21 17 18 seat 1 Mixing: according to the different mixing-material.
19 safefy covering switch 1 Choose the different mixing devices and speed.
20 fluctuate safety switch 1
18
21 overload protection switch 1
A: Be suitable for mix and stir butter, eggs, and work wi-
A
th in high speed, working time is less than 15 minutes.
axle
NOTES B. Be suitable for mix and stir stuffing and raw material,
B and work in middle speed, working time is less than 20
Machine at a factory hour have added to
note the superior quality lubricates the minutes.
screw
grease, usually the circumstance bottom C: middle position is suitable for mixing dough,
can use for several years, but machine is C working time is less than 30 minutes.Flour wat-
after maintaining, must replace the lubri- er quantity is 40%-50%.
cation grease.
axle
2 11
B10F/B10F-PG/B15F/B15F-PG Mixer Parts List B10F/B10F-PG/B15F/B15F-PG Mixer Parts List

Figure 9 STANDARD ACCESSORIES Figure 2 AXLE

Item Descviption Qty

16
5 1 cover 1
2 oil seal 25*40*10 1
6 1
3 bearing 6204
15
4 big joint gear 1
5 bearing ring 1
4 14
6 axle 1
7 joint 1
3 13
8 bearing ring 1
12
1 2 3 9 joint gear 1
11 10 dividing ring 1
2
10 11 engager 1

1 12 spring 8
Item Descviption Qty 9
13 roller 4
1 Mixing device I 1
14 gear ring 1
2 Mixing device II 1 1
15 plate ring
3 Mixing device III 1 8
16 bearing 6001 1
4 bowl 1
7

NOTES
4 NOTES
Any agitator is easily installed by simp-
Vertical sides of jaws must face Be sure to install correct position
ly raising it onto the mixing axle, and on another. (see Figure 2-1) and lubricate all
then rotating it counter-clockwise on t- of the pins in the sleeve drive wh-
he shaft until into place. To remove, ra- en reassembling.
ise the agitator on the shaft until it clea- Joint (7) must always be raised
and lowered smoothly. Be sure jo-
rs the lock and then rotate clockwise an-
int sleeve as shown in Figure 2-2.
d lower. Check oil seal, if serious oil leaks
All of tools are precisely fitted to the bo- from drip cup.
RIGHT WRONG
wl, rounded corners and easily remov-
able for cleaning. FIGURE 2-1 FIGURE 2-2

10 3
B10F/B10F-PG/B15F/B15F-PG Mixer Parts List B10F/B10F-PG/B15F/B15F-PG Mixer Parts List
Figure 3 GEAR AXLE Figure 8 TURNING PLATE AND MIXING AXLE
Item Descviption Qty 7 Item Descviption Qty
1 bearing 6001 2 1 mixing axle 1
1 2 gear axle 1 2 Oil seal 20*40*10 1
3 key 5*58 1 5 3 bearing 6003 1
4 gear 1 4 safety net 1
2 5 collar 1 5 planetary gear 1
6 gear 1 9 6 turning plate 1
7 long collar 1 7 inner gear 1
6
8 gear 1 8 cover 1
3 9 stop ring 1 9 bearing 6203 1
10 screw M8*20 1
11 ring 1
8
4
11
5 10
3
2
6
NOTES
7 Be sure that the keys are inserted
for each gear. 1
8
9
4
1
4 9
B10F/B10F-PG/B15F/B15F-PG Mixer Parts List B10F/B10F-PG/B15F/B15F-PG Mixer Parts List

Figure 7 HANDGRIP TYPE BOWL LIFTER UINT Figure 4 MOTOR UNIT

Item Qty Item Descviption Qty

Descviption
1 spiral 1
1 lifting bar 1
2 oil seal 1
2 cottor pin 3*30 1
3 bearing 203 2
3 nut M10 3
4 key 4*22 1
4
4 flat washer 2 axle 1
5 5
5 compression spring 1 6 switch 1

6 little knot 1 7 switch plastic 1

7 lifting handle bracket 1 8 screw M4*8 2
1
3 screw M6*16
flat washer 1 9 4
8
7 2 10 bearing cover 1
9 9 flange knot 1
11 fan 1
2 10 screw M6*25 1
11 key 5*20 1
11

6 12 bowl lift handle 1 11

NOTES
10
If the motor does not work, first v-
8
10 6 9 erify the power source and conn-
1
3 8
12 ection. Next, check for damaged
7 or faulty wiring or connections ins-
ide the mixer. A noworking motor
bearing cover may be the result of inappropriate
axle
fan
voltage, broken wires, a defective
capacitor, or a defective centrifugal
3 spiral
governor. Motor damage may also
4
be caused by bowl overload during
mixing.
5
oil seal
Motor set includes motor axle,rotor
bearing 203
and stator.
4
switch
Figure 4-1 is component system
switch plastic
3
diagrams of motor.
3 Figure 4-1

8 5
 B10F/B10F-PG/B15F/B15F-PG Mixer Parts List B10F/B10F-PG/B15F/B15F-PG Mixer Parts List
Figure 5 FORK AND SPEED SHAFT Figure 6 ARM AND BOWL LIFTER UINT
5
Item Descviption Qty 7 Item Descviption Qty
4
1 1 axle 1 6 1 screw 2
2 fork 1 2 arm 1
3
3 shaft 2 5 3 plate 2
4 spring 2 4 pull pole 1
5 nut 2 5 plate 1
6 bearing ring 1 6 gear 1
4
7 speed block 1 7 brace seat 1
8 spring 2 8 screw M8*20 1
9 shaft 1 9 sleev 1
8
2
10 plate 1 10 spiral 1
9 11 french support 1
3
12 french 1
4 13 13 handle 1
14 14 handle screw 1
10 5
8 15 nut 1
10
NOTES
11
9 The speed selector / shifting mech-
anism is designed for simplicity and
12 15
7 reliability. It features three mixing s-
peeds.
6 Speed selection is made by aligning
1 3
the pointer of the shifter handle with
the proper number on the shift sele-
ctor. Stop the mixer befor making any
speed changes.
Apply sealant to the shift selector as- 2
sembly, and install it .
fork
speed block
6 7