DC/DC Converters

TEN 4 Series, 4 Watt

e sign in
Features
rn e w d
m end ed fo
◆ Ultra-wide 4:1 input range
t re c o m
9 – 36 VDC or 18 – 75 VDC no
◆ Full SMD design
◆ High efficiency up to 85 %
◆ Indefinite short circuit protection
◆ I/O isolation 1‘500 VDC
◆ Input filter meets EN 55022, Class A
and FCC, Level A without external
components
◆ Shielded metal case with insulated
baseplate
◆ 24-pin DIP with industry standard pinout
◆ MTTF >1 Mio. h
◆ 3-year product warranty

The TEN 4 series DC/DC converter is designed for applications requiring very wide
operating voltage range. Typical applications are tele-and data communication
systems, mobile battery powered equipments and industrial process control systems
with operation from different input voltages i.e. 12/24 VDC or 24/48 VDC battery
voltages. High efficiency allows operation up to +75°C at full load. Input filtering
according to EN 55022-A and FCC, level A. Low output ripple minisme design-in
time and cost.

Models
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TEN 4-2410 3.3 VDC 900 mA 77 %
TEN 4-2411 5 VDC 660 mA 81 %
TEN 4-2412 12 VDC 330 mA 83 %
9 – 36 VDC
TEN 4-2413 15 VDC 265 mA 83 %
(24 VDC nominal)
TEN 4-2421 ±5 VDC ±300 mA 80 %
TEN 4-2422 ±12 VDC ±165 mA 83 %
TEN 4-2423 ±15 VDC ±130 mA 83 %
TEN 4-4810 3.3 VDC 900 mA 78 %
TEN 4-4811 5 VDC 660 mA 82 %
TEN 4-4812 12 VDC 330 mA 85 %
18 – 75 VDC
TEN 4-4813 15 VDC 265 mA 85 %
(48 VDC nominal)
TEN 4-4821 ±5 VDC ±300 mA 82 %
TEN 4-4822 ±12 VDC ±165 mA 85 %
TEN 4-4823 ±15 VDC ±130 mA 85 %

http://www.tracopower.com Page 1 of 3
 DC/DC Converters
TEN 4 Series 4 Watt

Input Specifications
Input current no load / full load 24 Vin models 20 mA typ. / 400 mA typ. (at 12 VDC Vin)
20 mA typ. / 200 mA typ. (at 24 VDC Vin)
48 Vin models 6 mA typ. / 200 mA typ. (at 24 VDC Vin)
6 mA typ. / 100 mA typ. (at 48 VDC Vin)
Start-up voltage / 24 Vin models 8.5 VDC / 8.0 VDC typ.
under voltage shut down 48 Vin models 17 VDC / 16 VDC typ.
Surge voltage (1 sec. max.) 24 Vin models 50 V max.
48 Vin models 100 V max.
Conducted noise (input) EN 55022 level A, FCC part 15, level A
Output Specifications
Voltage set accuracy ±1.0 %
Regulation – Input variation Vin min. to Vin max. 0.3 % max.
– Load variation 10 – 100 %
single output models 1.0 % max.
dual output models 1.0 % max. balanced load
3.0 % max. unbalanced load
Ripple and noise (20 MHz Bandwidth) 50 mVpk-pk max.
Temperature coefficient ±0.02 %/K
Current limitation >110 % of Iout max., constant current
Short circuit protection Hiccup mode, indefinite (automatic recovery)
Capacitive load – Single output models 3000 µF max.
– Dual output models 680 µF max.
General Specifications
Temperature ranges – Operating –40°C to +75°C
– Casing temperature +95°C max.
– Storage –40°C to +125°C
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTTF (MIL-HDBK-217F @ +25°C, ground benign) >1 Mio. h
Isolation voltage (60 sec.) – Input/Output 1’500 VDC
Isolation capacity – Input/Output 380 pF typ.
Isolation resistance – Input/Output (500 VDC) >1‘000 M Ohm
Switching frequency 350 kHz typ. (Pulse frequency modulation PFM)
Safety standards UL 1950 , IEC/EN 60950
Compliance up to 60 VDC input voltage
(SELV limit)
Safety approvals – UL/cUL www.ul.com > UL File no.: E188913

All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.

http://www.tracopower.com Page 2 of 3
 DC/DC Converters
TEN 4 Series 4 Watt

Physical Specifications
Casing material Steel chrome-nickel plated
Baseplate material Epoxy
Potting material Silicon rubber TSE (UL 94V-0 rated)
Weight 16.2 g (0.57 oz)
Soldering temperature max. 265°C / 10 sec.

Outline Dimensions
4.54 ±0.5
(0.18 ±0.02)

2.54 (0.1)

Pin-Out
Pin Single Dual
2 –Vin (GND) –Vin (GND)
23 2
3 –Vin (GND) –Vin (GND)
22 3
31.8 ±0.5 (1.25 ±0.02)

9 No pin Common
Bottom view
5.08 15.24 (0.6)
22.86 (0.9)

11 No function –Vout
14 +Vout +Vout
16 –Vout Common
16 9
22 +Vin (Vcc) +Vin (Vcc)
(0.2)

14 11 23 +Vin (Vcc) +Vin (Vcc)

Insulated Baseplate 0.5 2.4 ±0.5 15.22 (0.6) Dimensions in [mm], () = Inch
(0.02) (0.09 ±0.02) Pin diameter ø 0.5 ±0.05 (0.02 ±0.002)
4.1 10 ±0.5 20.3±0.5 Tolerances ±0.5 (±0.02)
Pin pitch tolerances ±0.35 (±0.014)
(0.16) (0.4 ±0.02) (0.8 ±0.02)

Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
Rev. October 6, 2021
www.tracopower.com Page 3 of 3