No.

0265
Rev 1.0
Date: 04/2022

SOFTWARE CABLE
REPAIR

PROGRAMMING

TESTING
3059 C18
MODULE CONNECTION
 No. 0265
Rev 1.0
Date: 04/2022

FEATURES DESCRIPTIONS

TEST CONNECTION EEPROM connection test

READ EEPROM Reading full EEPROM memory.
WRITE EEPROM Writing full EEPROM memory.
EDIT EEPROM Editing of full EEPROM memory.
SAVE TO FILE Save backup file to SDcard
RESTORE FROM FILE Restore saved backup file from SDcard
CHECK VALUE KM Reading of the KM value from the module
WRITE KM* Writing of the KM values to the module*
Swap bytes in buffer Swap bytes while Read/Write EEPROM (compatibility with other
programmers)
Swap bytes example
Oryginal Swap

KM<->Miles Kilometres to Miles conversion

SETUP Advanced settings while Read/Write EEPROM
* IN CASE OF PROGRAMMING MILEAGE OR HOURS OF OPERATION, THE SOFTWARE MAY BE USED SOLELY FOR REPAIR-RELATED PURPOSES. HOWEVER, IN SOME COUNTRIES ANY CHANGES
TO ODOMETER (CLOCK) READING OR TAMPERING WITH THE MILEAGE ACCURACY SHALL BE FORBIDDEN UNDER PENALTY.
PURSUANT TO ART. 306a OF THE POLISH PENAL CODE, WHOEVER ALTERS ODOMETERS OF MOTOR VEHICLES OR TAMPERS WITH THE MILEAGE ACCURACY SHALL BE SUBJECT TO THE
PENALTY OF DEPRIVATION OF LIBERTY FROM 3 MONTHS UP TO 5 YEARS. WHOEVER COMMISSIONS A THIRD PARTY TO PERFORM THE ABOVE-MENTIONED ACT SHALL BE SUBJECT TO
THE SAME PENALTY.
 No. 0265
Rev 1.0
Date: 04/2022

EDIT EEPROM
After reading the EEPROM select from MENU -> EDIT EEPROM

Swap bytes Swap bytes while Read/Write EEPROM

Fill Filling the preset part of the EEPROM memory with the appropriate data

Search Searching bytes in EEPROM

Save file… Save backup file to SDcard
Open file… Open saved backup file from SDcard
Close Close EDIT EEPROM and return to Menu
 No. 0265
Rev 1.0
Date: 04/2022

SETUP
During EEPROM programming please select from the MENU -> SETUP

Set voltage level Setting the EEPROM memory voltage level, range of 2,4-5V
Setting the delay time before READ/WRITE EEPROM memory,
Set delay time
range of 0-25000 ms
pullups on Pullup resistors active
Set pullups
pullups off Pullup resistors not active
on Autosave a Backup copy – on
Autobackup
of Autosave a Backup copy – off
 No. 0265
Rev 1.0
Date: 04/2022

ERROR MESAGES AND SOLUTIONS

ERROR MESSAGE:
Verify errors No XX
Where XX is the number of incorrectly written bytes after EEPROM verification (other value may appear)
e.g. Verify errors No 25
Where 25 is the number of incorrectly written bytes after EEPROM verification
SOLUTION
Please select different parameters
(available in EEPROM Setup → Set voltage level, Set delay 9me, Set pullups).

ERROR MESSAGE:
Overload protection mechanism triggered!
Power supply overload above 500mA.
SOLUTION
Disconnect C12,C13,C14,C18 cables or C19 cable from the module that is being programmed and restart
the program.
If error message does not appear after disconnecting C12,C13,C14,C18 or C19 cable it could mean that:
1. Cable could have been connected incorrectly
2. Short circuit may have occurred on the board of the module
3. Programming voltage could have been too high
If error message still appears please run EXTERNAL INTERFACE TEST

ERROR MESSAGE:
Power supply GROUND overload! - Overload protection mechanism triggered!
Power supply GROUND overload
SOLUTION
Disconnect DP4 from the module that is being programmed
Check the reason for overload:
4. Module could have been connected incorrectly
 There could have been system load
Wait 1 minute before reconnecting module
ERROR MESSAGE:
Automatic fuse restoration in progress. Restoration may take up to a few minutes.
Automatic fuse restoration is in progress.
SOLUTION
DP4 restoration may take 1 minute.
You must:
 Disconnect DP4 from the module that is being programmed
 Check the reason for overload,
 Try again.
 No. 0265
Rev 1.0
Date: 04/2022

LEGAL DISCLAIMER
It is forbidden to use DiagProg4 device, software for this device, information contained in this document and any other Elprosys
products for purposes which are illegal or prohibited in any other way. Elprosys and the company’s management board shall not be
liable for the results of the use of the DiagProg4 device, software, information contained in this document and any other Elprosys
products for purposes which are illegal or prohibited in any other way. Copying, redistribution, publishing, dissemination, sale,
giving access to or making use in any other way of the whole or part of the software and data contained in this document are
forbidden. Elprosys may introduce improvements or modifications of products on offer and their documentation as well instruction
manuals at any time without a prior notice. Any and all trademarks, product names and information set forth in the document are
the property of the Elprosys company and are protected by the law. A User is required to respect intellectual property rights of
resources contained in the document.

DIAGPROG4 TERMS OF USE

THE ELPROSYS COMPANY SHALL NOT BE HELD LIABLE FOR ANY ILLEGAL USE OF SOFTWARE AND HARDWARE. ANY
PURCHASED SOFTWARE AND HARDWARE SHALL BE USED FOR PURPOSES CONSISTENT WITH LEGAL PROVISIONS.

IN CASE OF PROGRAMMING MILEAGE OR HOURS OF OPERATION, THE SOFTWARE MAY BE USED SOLELY FOR REPAIR-
RELATED PURPOSES. HOWEVER, IN SOME COUNTRIES ANY CHANGES TO ODOMETER (CLOCK) READING OR TAMPERING
WITH THE MILEAGE ACCURACY SHALL BE FORBIDDEN UNDER PENALTY.

PURSUANT TO ART. 306a OF THE POLISH PENAL CODE, WHOEVER ALTERS ODOMETERS OF MOTOR VEHICLES OR
TAMPERS WITH THE MILEAGE ACCURACY SHALL BE SUBJECT TO THE PENALTY OF DEPRIVATION OF LIBERTY FROM 3
MONTHS UP TO 5 YEARS. WHOEVER COMMISSIONS A THIRD PARTY TO PERFORM THE ABOVE-MENTIONED ACT
SHALL BE SUBJECT TO THE SAME PENALTY.

IT SHALL BE FORBIDDEN, IN PARTICULAR, TO USE THE PURCHASED SOFTWARE OR PERFORM WITH ITS HELP ANY
CHANGES TO THE CAR CLOCKS, COMPUTERS, IMMOBILIZERS ETC., THAT MAY BE IN BREACH OF THE LAW OR BE
INDIRECTLY USED FOR CRIMINAL PURPOSES.

BY PURCHASING THE SOFTWARE, THE BUYER ACCEPTS PERSONAL LIABILITY FOR LEGAL USE OF THE SOFTWARE. THUS,
THE ELPROSYS COMPANY SHALL BE RELEASED FROM ANY LIABILITY FOR THE ILLEGAL USE OF THE SOFTWARE.

THE USER CONFIRMS TO HAVE READ THE PROVISIONS OF THE SOFTWARE LICENCE AGREEMENT AVAILABLE AT
WWW.ELPROSYS.COM/AGREEMENT/INDEX.HTML, AND TO HAVE ACCEPTED IT IN FULL.