MA2004-EA © 2020 CASIO COMPUTER CO., LTD.

Operation Guide 3488

About This Manual

x Note that the product illustrations in this manual are intended for reference only,
and so the actual product may appear somewhat different than depicted by an
illustration.

E-1

Contents Procedure Lookup

The following is a handy reference list of all the operational procedures contained in
About This Manual................................................................................................... E-1 this manual.
General Guide .......................................................................................................... E-4 To set the time and date .........................................................................................E-6
Timekeeping Mode .................................................................................................. E-6 To set the countdown start time ...........................................................................E-9
Countdown Timer Mode ......................................................................................... E-9 To use the countdown timer ................................................................................E-10
Stopwatch Mode ................................................................................................... E-12 To switch auto repeat timing and the progress beeper on and off..................E-11
Alarm Mode ............................................................................................................ E-17 To turn the Auto-Start function on and off .........................................................E-14
Dual Time Mode..................................................................................................... E-21 To set the Target Time and to turn it on and off ................................................E-15
To set the alarm time ............................................................................................E-17
Illumination............................................................................................................. E-23
To turn the daily alarm and hourly time signal on and off ................................E-19
Specifications ........................................................................................................ E-24
To test the alarm sound ........................................................................................E-20
To set the Dual Time .............................................................................................E-21
To turn on illumination ..........................................................................................E-23
E-2 E-3

General Guide x This watch returns to the Timekeeping Mode whenever you hold down the C
button for one or two seconds. If you ever lose track of what mode you are in or
x Press C to change from mode to mode. what you should do next, hold down C to return to regular timekeeping.
x After you perform an operation in any mode, pressing C returns to the x In any mode press L to illuminate the display.
Timekeeping Mode.
x If you do not press any button for a few minutes while making settings in any mode
(indicated when settings are flashing), the watch automatically clears the setting screen
(settings stop flashing) and returns to the normal display for the mode you are in.
Timekeeping Mode Countdown Timer Stopwatch Mode Alarm Mode Dual Time Mode
Mode

C C C C

C
E-4 E-5

Timekeeping Mode 3. While the seconds digits are selected (flashing), press D to reset the seconds
to 00. If you press D while the seconds count is in the range of 30 to 59, the
To set the time and date seconds are reset to 00 and 1 is added to the minutes. If the seconds count is in
PM indicator the range of 00 to 29, the minutes count is unchanged.
1. Hold down A while in the Timekeeping Mode until
the seconds digits flash on the display because they 4. While any other digits (beside seconds) are selected (flashing), press D to
Day of week increase the number or B to decrease it. While the 12/24-hour format setting is
are selected.
2. Press C to change the selection in the following selected, press D or B to toggle it between 12 and 24.
Month – Day
sequence. x Except for when adjusting the seconds or setting the 12/24-hour format, holding
down a button changes the current selection at high speed.
C C x When the 12-hour format is selected, the indicator P appears on the display to
Seconds Hour Minutes indicate “P.M.” times. There is no indicator for “A.M.” times.
x When the 24-hour format is selected, the indicator 24 appears on the display.
C x The year can be set in the range of 2000 to 2099.
C 12/24-Hour Format x The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
C change it except after you have the watch’s battery replaced.
Day Month Year x The day of the week is displayed automatically in accordance with the date (year,
Hour Minutes month, and day) settings.
C C
Seconds
E-6 E-7

5. After you set the time and date, press A to return to the Timekeeping Mode. Countdown Timer Mode
Minutes The countdown timer can be set within a range of
Auto repeat on 1 second to 24 hours. When the countdown reaches
Seconds indicator zero, an alarm sounds for 10 seconds or until you
Mode indicator press any button.
Current time To set the countdown start time
1. Hold down A while in the Countdown Timer
Mode. The hours digits flash on the display
because they are selected.
2. Press C to change the selection in the following
sequence.
C C
Hour Minutes Seconds

Progress
beeper on C
1/10 Seconds
indicator
E-8 E-9
 Operation Guide 3488
3. Press D to increase the selected number or B to decrease it. Holding down To switch auto repeat timing and the progress beeper on and off
either button changes the selection at high speed. 1. Hold down A while in the Countdown Timer Mode. The hour digits flash on the
x Press D and B at the same time to clear the starting time to 0:00' 00". display because they are selected. Press A again to move the flashing to the auto
x To set the starting value of the countdown time to 24 hours, set 0:00' 00". repeat ON/OFF setting.
4. After you set the countdown start time, press A twice to return to the Countdown 2. Press D or B to toggle auto repeat on ( ) and off.
Timer Mode. 3. Press C to move the flashing to the progress beeper ON/OFF setting.
4. Press D or B to toggle the progress beeper on ( ) and off.
To use the countdown timer 5. Press A to return to the Countdown Timer Mode.
1. Press D while in the Countdown Timer Mode to start the countdown timer. x When the end of the countdown is reached while auto repeat is on, the alarm
2. Press D again to stop the countdown timer. sounds, but the countdown restarts from the beginning without stopping. You
x You can resume countdown timer operation by pressing D. can stop the countdown by pressing D and manually reset to the start time by
3. Stop the countdown timer and then press B to reset the countdown time to its pressing B.
starting value. x If you set a starting time of 10 seconds or less and have Auto Repeat turned on,
x When the end of the countdown is reached and auto repeat timing is off, the the countdown timer tone (which normally sounds for 10 seconds) sounds for only
alarm sounds for 10 seconds or until you stop the alarm by pressing any button. one second.
Countdown timing stops and the countdown time is automatically reset to its x When the progress beeper is turned on, the watch beeps as the countdown time
starting value after the alarm stops. passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20, 10, 5, 4, 3, 2,
and 1-second marks.

E-10 E-11

Stopwatch Mode (a) Elapsed time measurement

The Stopwatch Mode lets you measure elapsed D D D D B

Minutes
time, split times, and two finishes. The range of the Start Stop Resume Stop Reset
Seconds stopwatch is 23 hour, 59 minutes, 59.99 seconds. (b) Split time measurement
Mode indicator You can also have an alarm sound when a target
time is reached. The Stopwatch Mode also features D B B D B
Current time
an Auto-Start function. Start Split Split release Stop Reset
(c) Split time and two finishes
D B D B B
Start Split Stop Split release Reset
First runner Second runner Record time of
finishes. finishes. second runner.
Record time of
first runner.
Target time
on indicator
1/100 Seconds
E-12 E-13

About the Auto-Start function To set the Target Time and to turn it on and off
With the Auto-Start function, the watch performs a 5-second countdown. When the 1. While the display is showing all zeros in the
countdown reaches zero, stopwatch operation starts automatically. During the final Seconds Stopwatch Mode, hold down A, and the hour
three seconds of the countdown, a beeper sounds with each second. digit of the target time starts to flash because it
Mode indicator is selected.
To turn the Auto-Start function on and off Hour 2. Press C to change the selection in the following
While the display is showing all zeros in the Stopwatch Mode, press B to toggle it sequence.
on and off. C C
x The indicator A.START appears and 05 is shown in the upper display while Auto- Hour Minutes Seconds
Start is turned on. The A.START indicator is not shown and the upper part of the
display shows the current time when Auto-Start is turned off.
C
About the Target Time function 3. Press D to increase the selected number or B to
With the Target Time function, an alarm sounds for ten seconds whenever the time decrease it. Holding down either button changes
being kept by the stopwatch reaches a target time you have preset. the selection at high speed.
x Press D and B at the same time to clear the
Target time on indicator setting to 0:00' 00".
Minutes
E-14 E-15

4. Press A to move the flashing to the target time ON/OFF setting. Alarm Mode
5. Press D or B to toggle the target time on and off.
6. Press A to return to the Stopwatch Mode. When the Daily Alarm is switched on, the alarm
Hourly time signal on indicator sounds for 20 seconds at the preset time each day.
Important!
Press any button to stop the alarm after it starts
The alarm will not sound if you do not turn on the target time. Alarm on indicator to sound. When the Hourly Time Signal is on, the
x Press A, C or L to stop the alarm after it starts to sound. watch beeps every hour on the hour.
Mode indicator
To set the alarm time
Current time
1. Hold down A until the hour digits start to flash
on the display. The hour digits flash because they
are selected.
xThis operation will switch the Daily Alarm on
automatically.
2. Press C to change the selection in the following
sequence.
C
Hour Minutes Hour Minutes
E-16 E-17

3. Press D to increase the selected digits and B to decrease them. Holding down To turn the daily alarm and hourly time signal on and off
either button changes the selection at high speed. Press B while in the Alarm Mode to change the status of the daily alarm and hourly
x The format (12-hour and 24-hour) of the alarm time matches the format you time signal in the following sequence.
select for regular timekeeping.
B B B
x When setting the alarm time using the 12-hour format, take care to set the time Daily Alarm Hourly Time
correctly as morning (no indicator) or afternoon (P). Both OFF Only Signal Only Both ON
4. After you set the alarm time, press A to return to the Alarm Mode.

x The alarm on indicator ( ) and the Hourly Time Signal on indicator ( ) are shown
on the display in all modes while these functions are turned on.

E-18 E-19
 Operation Guide 3488
To test the alarm sound Dual Time Mode
Hold down B while in the Alarm Mode to sound the alarm.
x Note that pressing B also changes the alarm and the hourly time signal ON/OFF The Dual Time Mode lets you keep track of the time in
settings. Mode indicator another time zone. You can also select the timekeeping
format (12-hour or 24-hour) separately from the
Current time
Timekeeping Mode.

To set the Dual Time

1. Hold down A while in the Dual Time Mode. The hour
digits flash on the display because they are selected.
2. Press C to change the selection in the following
sequence.
C
Hour Minutes
Hour Minutes
3. Press D to increase the selected digits and B to
decrease them. Holding down either button changes
the selection at high speed.
E-20 E-21

4. After you set the time, press A to return to the Dual Time Mode. Illumination
x In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode. The face of the watch is illuminated for easy reading in
x In the Dual Time Mode, press B to toggle between the 12-hour and 24-hour the dark.
formats.
To turn on illumination
In any mode (except when a setting mode, with flashing
digits is on the display), press L to illuminate the display.
Illumination Precautions
x Illumination may be hard to see when viewed under
direct sunlight.
x Illumination turns off automatically whenever an alarm
sounds.
x Frequent use of illumination runs down the battery.

E-22 E-23

Specifications Dual Time

Illumination: LED (light-emitting diode)
Accuracy at normal temperature: ±30 seconds a month Battery: One lithium battery (Type: CR2025)
Timekeeping: Hour, minutes, seconds, pm (P), day of the week, month, day Battery life: 10 years under the following conditions
Time format: 12-hour and 24-hour formats x One 2-second light operation per day
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099 x One 20-second alarm operation per day
Countdown Timer
Measuring unit: 1/10 second
Input range: 1 second to 24 hours
Others: Auto repeat function, progress beeper function
Stopwatch
Measuring unit: 1/100 second
Measuring capacity: 23 hours 59 minutes, 59.99 seconds
Measuring modes: Elapsed time, split time and two finishes
Others: Target Time Alarm, Auto-Start
Alarm: Daily alarm, hourly time signal

E-24 E-25