CE-2124 Fluid Mechanics

Fluid Statics
Content Topics
• Fluid Static & Pascal Law
• Relationship between Pressure and elevation
• Fluid Pressure on Immersed, Vertical and
Inclined Surfaces
• Centre of pressure
 Fluid Statics
• Fluid Statics means fluid at rest.
• At rest, there are no shear stresses, the only force is the
normal force due to pressure is present.
• Pressure is defined as:
• “Force per Unit Area” Or
“The amount of force exerted on a unit area of a substance or
on a surface.”
• This can be stated by the equation:
dF
(For Finite Area) p  dA (For Infinitsma l Area)
F
p
A
• Units : N/m2(Pa), lbs/ft2 (psf), lbs/in2 (psi)
 Example
A load of 200 pounds (lb) is exerted on a piston confining oil
in a circular cylinder with an inside diameter of 2.50 inches
(in). Compute the pressure in the oil at the piston.
Solution:
 Principles about Pressure
• Two important principles about pressure were described by
Blaise Pascal, a seventeenth-century scientist:
1. Pressure acts uniformly in all directions on a small volume of
a fluid.
2. In a fluid confined by solid boundaries, pressure acts
perpendicular to the boundary.
Direction of fluid pressure on boundaries
 Pressure expressed in Height of Fluid

• The term elevation means the vertical distance from

some reference level to a point of interest and is
called z.
• A change in elevation between two points is called h.
Elevation will always be measured positively in the
upward direction.
• In other words, a higher point has a larger elevation
than a lower point.
• Fig shows the illustration of reference level for
elevation.
Relationship between Pressure and Elevation:
 Pressure Head
• It is the pressure expressed in terms of height of fluid.
p
h
g
• h=p/g represents the energy per unit wt. stored in the fluid by
virtue of pressure under which the fluid exists. This is also
called the elevation head or potential head.
 Example
An open tank contains water 1.40m deep covered by a 2m
thick layer of oil (s=0.855). What is the pressure head at the
bottom of the tank, in terms of a water column?
Solution:
g w  9.81kN / m 3
g o  0.855 x9.81  8.39 kN / m 3
For interface : p i  g o ho  8.39 x 2  16 .78 kN / m 2
for water equivalentof oil :
p 16 .78
h oe  i   1.710 m
g w 9.81
So h we  hw  h oe  1.40  1.710  3.11m
SOLUTION  2
pb  g o ho  g w hw
 (8.39)2  9.81(1.4)
 30.51kN/m 2
pb 30 .51
hwe    3.11m
g w 9.81
 Exercises:
1. An open tank contains 5 m water covered with 2 m of oil
(g8kN/m3). Find the gauge pressure (a) at interface between
the liquids and at bottom of the tank.
2. An open tank contains 7ft of water covered with 2.2ft oil
(s=0.88). Find the gauge pressure (a) at the interface between
the liquids and (b) at the bottom of the tank.
3. If air had a constant specific weight of 12N/m3and were
incompressible, what would be the height of air surrounding
the earth to produce a pressure at the surface of 101.3 kPa
abs?
Total Fluid Pressure on Immersed
Surfaces

Ch-3 by RS Khurmi
Total Fluid Pressure on Immersed
Surfaces

Ch-3 by RS Khurmi
Total Fluid Pressure on Vertically
Immersed Surfaces
Total Fluid Pressure on Vertically
Immersed Surfaces
Total Fluid Pressure on Vertically
Immersed Surfaces
Total Fluid Pressure on Vertically
Immersed Surfaces
Total Fluid Pressure on Inclined
Immersed Surfaces
Total Fluid Pressure on Inclined
Immersed Surfaces
Total Fluid Pressure on Inclined
Immersed Surfaces
Centre of Pressure
 Centre of Pressure

For details see 3.8 (Khurmi) Centre of Pressure Vertically Immersed Surface
Centre of Pressure
Centre of Pressure
Geometrical Properties of some important
Plane Surfaces
Example
Example
 Content Topics
• Absolute and Gage Pressure
• Measurement of Pressure
• Pressure measurement devices
 Absolute and Gage Pressure
• Atmospheric Pressure: It is the force per unit area exerted by the
weight of air above that surface in the atmosphere of Earth (or that
of another planet). It is also called as barometric pressure.
• Gauge Pressure: It is the pressure, measured with the help of
pressure measuring instrument in which the atmospheric pressure
is taken as Datum (reference from which measurements are made).
• Absolute Pressure: It is the pressure equal to the sum of
atmospheric and gauge pressures. Or
• If we measure pressure relative to absolute zero (perfect Vacuum)
we call it absolute pressure.
• Vacuum: If the pressure is below the atmospheric pressure we call
it as vacuum.
pabs  patm  p gage
 Measurement of Pressure
• There are many ways to measure pressure in a
fluid. Some are discussed here:
1. Barometers
2. Bourdon gauge
3. Pressure transducers
4. Piezometer Column
5. Simple Manometers
6. Differential Manometers
 1. Barometers:
• To measure the atmospheric pressure.
• Procedure:
1. Immerse the open end of tube in a liquid
which is open to atmosphere.
2. The liquid will rise in the tube if we
exhaust air from the tube.
3. If all the air is removed and the tube is
long enough, than only pressure on the
surface is the vapour pressure and liquid
will reach its max. possible height (y).
pO  p a  p atm  gy  pvapour
If the vapour pressureon liquid surfacein tube is negligible than :
p atm  gy
 2. Bourdon Gauge:
• The pressure, above or below the atmospheric pressure,
may be easily measured with the help of a bourdon’s
tube pressure gauge.
• It consists on an elliptical tube: bent into an arc of a
circle. This bent up tube is called Bourdon’s tube.

 Tube changes its curvature with

change in pressure inside the tube.
Higher pressure tends to
“straighten” it.
 The moving end of tube rotates
needle on a dial through a linkage
system.
 3. Piezometer Column/Tube:
• A piezometer tube is the simplest
form of instrument, used for
measuring, moderate pressure.
• It consists of long tube in which the
liquid can freely rise without
overflowing.
• The height of the liquid in the tube
will give the pressure head (p/g)
directly.
 4. Manometer:
• Manometer is an improved form of a
piezometer tube. With its help we can
measure comparatively high pressures and
negative pressure also. Following are few
types of manometers.
1. Simple Manometer
2. Micro-manometer
3. Differential manometer
4. Inverted differential manometer
 Simple Manometer:
• It consists of a tube bent in U-Shape, one end
of which is attached to the gauge point and
the other is open to the atmosphere.
• Mercury is used in the bent tube which is 13.6
times heavier than water. Therefore it is
suitable for measuring high pressure as well.
Procedure:
1. Consider a simple Manometer connected to a
pipe containing a light liquid under high
pressure. The high pressure in the pipe will
force the mercury in the left limb of U-tube to
move downward, corresponding the rise of
mercury in the right limb.
 Simple Manometer:
2. The horizontal surface, at which the heavy and light liquid meet in
the left limb, is known as datum line.
Let h1 = height of light liquid in the left limb above datum.
h2 = height of heavy liquid in the right limb above datum.
h= Pressure in the pipe, expressed in terms of head of water.
s1=Sp. Gravity of light liquid.
s2=Sp. Gravity of heavy liquid.
3. Pressure in left limb above datum = h +s1h1
4. Pressure in right limb above datum = s2h2
5. Since the pressure is both limbs is equal So,
h +s1h1 = s2h2
h= (s2h2 - s1h1)
 Simple Manometer:
To measure negative pressure:
In this case negative pressure will suck the light liquid which
will pull up the mercury in the left limb of U-tube.
Correspondingly fall of liquid in the right limb.

6. Pressure in left limb above datum = h +s1h1 + s2h2

7. Pressure in right limb = 0
8. Equating, we get
h = -s1h1-s2h2 = -(s1h1+s2h2)
 Example
A simple manometer containing mercury is used to measure the
pressure of water flowing in a pipeline. The mercury level in the open
tube is 60mm higher than that on the left tube. If the height of water in
the left tube is 50mm, determine the pressure in the pipe in terms of
head of water.
Solution:
Pressurehead in the left limb aboveZ - Z
 h  s1h1  h  (1x50)
 h  50 mm
Pressurehead in the right limb aboveZ - Z
 s 2 h2  13.6 x60
 816 mm
Equating;
h  50  816
h  766 mm
 Example
A simple manometer containing mercury was used to find the
negative pressure in pipe containing water. The right limb of the
manometer was open to atmosphere. Find the negative pressure,
below the atmosphere in the pipe.
Solution:

Pressurehead in the left limb aboveZ - Z

 h  s1h1  s 2 h2  h  (1x50)  (13.6 x50)
 h  700 mm
Pressurehead in the right limb aboveZ - Z
0
Equating;
h  700  0
h  -700 mm  -7m
Gauge pressurein the pipe  p  g h
9.81x(-7)  - 68.67kN/m 2
 -68.67kPa
 68.67kPa (Vacuum)
 Example
Figure shows a conical vessel having its outlet at A to which U tube
manometer is connected. The reading of the manometer given in figure
shows when the vessel is empty. Find the reading of the manometer
when the vessel is completely filled with water.
Solution:

h 2  200 mm  0.2m
s1  1 and s 2  13 .6
Let h  Pressurehead of mercury in terms on head of water.
1. Let us consider the vesselis to be empty and Z - Z be the datum line.
Pressurehead in the right limb aboveZ - Z
 s1h1  1xh  h
Pressurehead in the left limb aboveZ - Z
 s 2 h2  13 .6 x0.2  2.72 m
Equating; h  2.72m
2. Consider the vesselto be completely filled with water.
As a result, let the mercury level goes down by x meters in the right limb, and
the mercury level go up by thesame amount in the left limb.
Therefore total height of water in the right limb
 x  h  3  x  2.72  3  x  5.72
Pressurehead in the right limb  1(x  5.72)  x  5.72
We know that manometer reading in this case:
 0.2  2x
Pressurehead in the left limb
 13.6 (0.2  2x)  2.72  27.2x
Equating the pressures:
x  5.72  2.72  27.2x
x  0.115m
and manometer reading  0.2  (2x0.115)  0.43m  430 mm
 Differential Manometer:
• It is a device used for measuring the difference of pressures,
between the two points in a pipe, or in two different pipes.
• It consists of U-tube containing a heavy liquid (mercury)
whose ends are connected to the points, for which the
pressure is to be found out.
Procedure:
 Let us take the horizontal surface Z-Z, at which heavy liquid
and light liquid meet in the left limb, as datum line.
 Let, h=Difference of levels (also known as differential
manomter reading)
ha, hb= Pressure head in pipe A and B, respectively.
s1, s2= Sp. Gravity of light and heavy liquid respectively.
 Differential Manometer:
1. Consider figure (a):
2. Pressure head in the left limb above
Z-Z = ha+s1(H+h)= ha+s1H+s1h

3. Pressure head in the right limb above

Z-Z = hb+s1H+s2h
4. Equating we get,
ha+s1H+s1h = hb+s1H+s2h
ha-hb=s2h-s1h = h(s2-s1)
 Differential Manometer:
Two pipes at different levels:
1. Pressure head in the left limb above Z-Z
= ha+s1h1
2. Pressure head in the right limb above Z-Z
= s2h2+s3h3+hb
3. Equating we get,
ha+s1h1 = s2h2+s3h3+hb
Where;
h1= Height of liquid in left limb
h2= Difference of levels of the heavy liquid in the right and left
limb (reading of differential manometer).
h3= Height of liquid in right limb
s1,s2,s3 = Sp. Gravity of left pipe liquid, heavy liquid, right pipe
liquid, respectively.
 Example
A U-tube differential manometer connects two pressure pipes A and B.
The pipe A contains carbon Tetrachloride having a Sp. Gravity 1.6 under
a pressure of 120 kPa. The pipe B contains oil of Sp. Gravity 0.8 under a
pressure of 200 kPa. The pipe A lies 2.5m above pipe B. Find the
difference of pressures measured by mercury as fluid filling U-tube.
Solution:
Given : s a  1.6, p a  120kPa; s b  0.8, p b  200kPa;
h1  2.5m and s  13.6
Let h  Differnce of pressure measured by
mercury in terms of head of water.
We know that pressure head in pipe A,
pa 120
  7.65m
g 15.696
p b 200
Pressure head in pipe B,   25.5m
g 7.85
We also know that pressure head in Pipe A above Z - Z
 7.65  (s a . h1 )  s.h
 7.65  (1.6 x 2.5)  13.6 x h
 11.65  13.6 h
Pressure head in Pipe B above Z - Z
 24.5  s b h  25.5  (0.8 x h)
Equating;
11.65  13.6 h  25.5  (0.8 x h)
h  1.082 m
 Inverted Differential Manometer:
• Type of differential manometer in which an inverted U-tube is used.
• Used for measuring difference of low pressure.
1. Pressure head in the left limb above Z-Z = ha-s1h1
2. Pressure head in the right limb above Z-Z = hb-s2h2-s3h3
3. Equating we get, ha-s1h1 = hb-s2h2-s3h3

(Where; ha, hb are Pressure in pipes A and B

expressed in terms of head of liquid, respectively)
 Numerical Exercise-1:
1. A simple manometer is used to measure the pressure of oil (sp.
Gravity = 0.8) flowing in a pipeline. Its right limb is open to the
atmosphere and the left limb is connected to the pipe. The centre
of pipe is 90mm below the level of mercury (sp. Gravity = 13.6) in
the right limb. If the difference of mercury levels in the two limbs
is 150mm, find the pressure of oil in pipe.
 Numerical Exercise-2:
2. The pressure of water flowing in a pipeline is measured by a
manometer containing U-tubes as shown in figure. The
measuring fluid is mercury in all the tubes and water is
enclosed between the mercury columns. The last tube is
open to the atmosphere. Find the pressure of oil in the
pipeline.
 Numerical Exercise-3:
3. A differential manometer connected at the two points A and
B at the same level in a pipe containing an oil of Sp. Gravity
0.8, shows a difference in mercury levels as 100mm.
Determine the difference in pressures at the two points.
Thankyou