Scribd
Upload
58 views12 pages

Mercedes CAN Filter Connection Manual

The document provides installation instructions for the Mercedes CAN filter for various models including ML W164, GL X164, R-class W251, C-class W204, E-class W212, and S-class W221. Each model requires the removal of the EZS, preparation of the CAN filter board, and specific wiring connections to the EZS board. Insulation of the CAN filter board is necessary after installation to ensure proper functioning.

Uploaded by

Sorin Baican
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
58 views12 pages

Mercedes CAN Filter Connection Manual

The document provides installation instructions for the Mercedes CAN filter for various models including ML W164, GL X164, R-class W251, C-class W204, E-class W212, and S-class W221. Each model requires the removal of the EZS, preparation of the CAN filter board, and specific wiring connections to the EZS board. Insulation of the CAN filter board is necessary after installation to ensure proper functioning.

Uploaded by

Sorin Baican
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

CODECARD Mercedes CAN filter connection manual

1. Mercedes ML W164, GL X164, R-class W251 installation instructions

In these models Mercedes use 2 kinds of EZS (also named EIS-electronic ignition switch): in older
cars <2007 - with 9S12 processor, in new cars 2007+ - EZS with AMAZONAS processor. Mercedes
CAN filter will work with both EZS types. For installation remove EZS from car.

• For first prepare Mercedes CAN filter board: remove resistor marked in picture and solder
first configuration points. Use fine KYNAR wire for installation.

1
Remove from EZS board SMD part marked with red “X”. With short, good isolated wire connect
Mercedes CAN filter to EZS board according picture: 1-1 (C1H), 2-2(C1L), 3-3(C2H), 4-4(C2L), 5-
5(GND), and 6-6 (+5V).

Mercedes ML W164, GL X164, R-class W251 Type 1:

2
Mercedes ML W164, GL X164, R-class W251 Type 2:

After connection insulate Mercedes CAN filter board with heat shrink or insulation tape. Put it carefully
to EZS casing.

3
2. Mercedes C-class W204 installation instructions.

In these models Mercedes use new EZS with NEC processor marked IRLAND or HAVANNA (also
named EIS-electronic ignition switch). Mercedes CAN filter will work with both EZS types. For
installation remove EZS from car.

• For first prepare Mercedes CAN filter board: check - resistor 121 must be soldered and
solder second configuration points like in pictures.

4
Remove EZS board from casing. Carefully disconnect board from mechanic – look on picture.

Remove from EZS board SMD part marked with red “X”. With short, good isolated wire connect
Mercedes CAN filter to EZS board according picture: 1-1 (C1H), 2-2(C1L), 3-3(C2H), 4-4(C2L), 5-
5(GND), and 6-6 (+5V).

5
After connection insulate Mercedes CAN filter board with heat shrink or insulation tape. Put it carefully
to EZS casing.

6
3. Mercedes E-class W212 installation instructions.

In these models Mercedes use new EZS with NEC processor marked JURA (also named EIS-electronic
ignition switch). Mercedes CAN filter will work with both EZS types. For installation remove EZS from
car.

• For first prepare Mercedes CAN filter board: check - resistor 121 must be soldered and
solder second configuration points like in pictures.

7
Remove EZS board from casing. Carefully disconnect board from mechanic – look on picture.

Remove from EZS board SMD part marked with red “X”. With short, good isolated wire connect
Mercedes CAN filter to EZS board according picture: 1-1 (C1H), 2-2(C1L), 3-3(C2H), 4-4(C2L), 5-
5(GND), and 6-6 (+5V).

8
After connection insulate Mercedes CAN filter board with heat shrink or insulation tape. Put it carefully
to EZS casing.

9
4. Mercedes S-class W221 installation instructions

Mercedes W221 use new EZS with NEC processor marked IRLAND or HAVANNA (also named EIS-
electronic ignition switch). Mercedes CAN filter will work with both EZS types. For installation remove
EZS from car.

• For first prepare Mercedes CAN filter board: check - resistor 121 must be soldered and
solder second configuration points like in pictures.

10
Remove from EZS board SMD part marked with red “X”. With short, good isolated wire connect
Mercedes CAN filter to EZS board according picture: 1-1 (C1H), 2-2(C1L), 3-3(C2H), 4-4(C2L), 5-
5(GND), and 6-6 (+5V).

Mercedes S-class W221 Type 1:

11
Mercedes S-class W221 Type 2:

12

You might also like