Module 2 3d Living Room Mark
Module 2 3d Living Room Mark
INSTRUCTIONAL MATERIALS
2
LE
MODULE 6: CREATING 3D furniture’s
U
D
OBJECTS for living room
O
M
D
A
Prepared by
C
TO
Associate Professor V
A
F
LF
Command: EXTRUDE
2
LE
In the drawing space activate SW viewport/ set the coordinates
TOP / select EXTRUDE from the modelling menu panel
U
Command Line: Select object to extrude
D
In Drawing Space: select rectangle A enter/ drag upward
Command Line: Specify the height/ Type 300/ enter (Fig.2)
O
Use the same procedure for B, C and D use the M
for B and C height = 600, for D height = 900 (Fig. 3)
2
In drawing space: SW Viewport / EXTRUDE
Circle H = 100/ enter
LE
U
D
O
M
Figure 8. Front View showing the position of throw pillows
D
Before rotating the throw, pillow change the visual view from
A
Command: ROTATE
TO
Command: MOVE (Before moving the object turn off ON SNAP keys and turn on
ORTHOGRAPHIC KEY
Click move in modify panel
Command Line: Select object to move
In drawing space: Click the object / enter
Command Line: Specify basepoint or displacement: TYPE -100, 175, 0/ enter/ enter (Figure 11)
Note: Movement of the object should be in FRONT View since moving the object toward Left
side the value of X should be negative (-), for Y value it is upward therefore it should be
positive, the value of Z is zero since moving is in FRONT VIEW.
2
LE
U
D
O
M
6.4. creating SIDE TABLE
D
Command: RECTANGLE
A
Command: OFFSET
TO
Command: RECTANGLE
A
Command: EXTRUDE
F
Command: MOVE
Select Move Icon from modify panel
In the drawing space: Select the object / rectangle 4/ enter
Displacement / height: 400 / enter (Figure 16)
Command: MOVE
In the drawing space: Select rectangle 2 / enter
Displacement / height: -100 / enter (moving downward) (Figure 16)
Command: SUBTRACT
Click SUBTRACT icon in Solid Editing Panel
2
Select rectangle 2/ Enter (Figure 17)
LE
Command: MOVE
Click Move icon in modify panel
U
D
Command Line: Select objects to move
In drawing space: Select Object subtracted / enter
O
Click the base point or first point /
Specify the second point or displacement
M
TYPE 0,0, 300 / Enter / Enter (Figure 18)
D
Command: EXTRUDE
A
Command: MOVE
Click Move Icon in modify panel
A
Command: FILLET
Click FILLET Icon in the Modify Panel
Command: RECTANGLE
Create Rectangle @ 1000, 600 / Enter
Follow same procedure as for Side Table
Command: RECTANGLE
Create Rectangle @ 1000, 1000 / Enter
2
Command: OFFSET
Offset Rectangle 1 with distance = 50
LE
For rectangle 2 and 3
Command: LINE
U
Create LINE for the following points
D
Set coordinates TOP on SW View
Points A to J and B to J = 900
O
Points C to E, D to G, A to F and B to H = 600 M
Points C to K, D to L, A to M, and B to N = 400(Figure 21)
Command: RECTANGLE
D
Command: FILLET
U
A
Command: CIRCLE
Change coordinate to FRONT and create circle at
LF
Command: SWEEP
Click Sweep icon in modelling panel
Select circle for the object and rectangle ABIJ for the path
Same procedure for other rectangle BDHG, ACFM
And CDKL/ enter (Figure 24)
Command: FILLET
Fillet all sides use R = 100 for rectangle MNIJ
And rectangle KLMN (Figure 26)
Command: EXTRUDE
Click Extrude Icon in the modelling panel
2
Select objects rectangle MNIJ thickness = 100
LE
Coordinates should be FRONT
U
Coordinates should be in TOP
D
Command: FILLET
O
Fillet all edges and use R = 100 (Figure 27) M
6.7 Creating round Tube SOFA 2
D
A
Command: CIRCLE
A
Command: RECTANGLE
Create Rectangle @1500,800 / Enter
Get the midpoint for both vertical and horizontal
Command: ELLIPSE
Click ellipse icon in draw panel
In the drawing space: Click center point of rectangle / drag
At point B and drag at point A / Enter (ellipse 1)
2
Command: OFFSET
Offset ellipse 1 distance = 100 (ellipse 2)
LE
Command: CIRCLE
Create Circle 1 D = 75 at point A, B, C, and D
U
Create Circle 2 at point C and point D drag to the edge
D
Of ellipse (Figure 20)
O
Command: EXTRUDE M
Extrude circle at point A,B,C and D. height = 400
Command: COPY
D
Command: SPLINE
Draw a Spline 1 same as in figure 31
TO
Command: MIRROR
Mirror Spline 1 = Spline 2
U
A
Command: MOVE
Move Spline 1 height 0,0, 150/ Enter / Enter
F
Command: EXTRUDE
Ellipse 1, Spline 1, and Spline 2
Extrude height = 25 / Enter (Figure 32)