ECS-9000 USER

Manual
Intel® Xeon®/Core™ i7/i5/i3 Fanless Embedded System
Workstation-grade, Rugged, -40°C to 75°C Extended Temperature

1.9.0 Edition 20230531

Record of Revision
Version Date Page Description Remark
1.0 11/25/2016 All Official Release
1.1 05/09/2017 97 Update
1.2 06/15/2017 37-38,103-123 Update
1.3 02/02/2018 2-22 Update
1.4 11/16/2018 All Remove M2DOM
1.5 07/26/2019 31 Update
1.6 03/19/2021 3, 5, 8, 10, 13, 15, 17, Update
19, 22, 24, 38
1.7 04/21/2021 52 Update
1.8 05/23/2022 124-126 Update
1.9 05/31/2023 vii, 31, 55, 114 Update

ii
Disclaimer
This manual is released by Vecow Co., Ltd. for reference purpose only. All
product offerings and specifications are subject to change without prior notice.
It does not represent commitment of Vecow Co., Ltd. Vecow shall not be liable
for direct, indirect, special, incidental, or consequential damages arising out of
the use of the product or documentation or any infringements upon the rights of
third parties, which may result from such use.

Declaration of Conformity
FCC This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy, and if it is not installed and used
in accordance with the instruction manual, it may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference at his own expense.

CE The products described in this manual complies with all applicable European
Union (CE) directives if it has a CE marking. For computer systems to
remain CE compliant, only CE-compliant parts may be used. Maintaining CE
compliance also requires proper cable and cabling techniques.

Copyright and Trademarks

This document contains proprietary information protected by copyright. No part
of this publication may be reproduced in any form or by any means, electric,
photocopying, recording or otherwise, without prior written authorization
by Vecow Co., Ltd. The rights of all the brand names, product names, and
trademarks belong to their respective owners.

iii
Order Information
Part Number Description
ECS-9000, 9 GigE LAN with 4 PoE+, 2 Front-access SSD Tray,
ECS-9000-9R
6 USB 3.0, 4 COM, 3 SIM, Isolated DIO
ECS-9000, 9 GigE LAN with 4 PoE+, 6 USB 3.0, 4 COM, 3 SIM,
ECS-9000-9GD
16 Isolated DIO
ECS-9000, 6 GigE LAN with 4 PoE+, 2 Front-access SSD Tray,
ECS-9000-PoER
6 USB 3.0, 4 COM, 3 SIM, Isolated DIO
ECS-9000, 6 GigE LAN with 4 PoE+, 6 USB 3.0, 4 COM, 3 SIM,
ECS-9000-PoE
Isolated DIO
ECS-9000, 6 GigE LAN with 2 SFP, 2 Front-access SSD Tray,
ECS-9000-6FR
6 USB 3.0, 4 COM, 3 SIM, 16 GPIO
ECS-9000, 6 GigE LAN with 2 SFP, 6 USB 3.0, 4 COM, 3 SIM,
ECS-9000-6F
16 GPIO
ECS-9000, 4 GigE LAN, 2 Front-access SSD Tray, 6 USB 3.0,
ECS-9000-4R
4 COM, 3 SIM, 16 GPIO
ECS-9000-4G ECS-9000, 4 GigE LAN, 6 USB 3.0, 4 COM, 3 SIM, 16 GPIO
ECS-9000, 2 GigE LAN, 2 Front-access SSD Tray, 6 USB 3.0,
ECS-9000-2R
4 COM, 3 SIM, 16 GPIO
ECS-9000-2G ECS-9000, 2 GigE LAN, 6 USB 3.0, 4 COM, 3 SIM, 16 GPIO

Order Accessories
Part Number Description
7th Gen Intel® Xeon® E3-1275 v6 Processor (8M Cache, up to
E3-1275 v6
4.20GHz, 80W)
6th Gen Intel® Xeon® E3-1275 v5 Processor (8M Cache, up to
E3-1275 v5
4.00GHz, 80W)
6th Gen Intel® Xeon® E3-1225 v5 Processor (6M Cache, up to
E3-1225 v5
3.70GHz, 80W)
6th Gen Intel® Xeon® E3-1268L v5 Processor (8M Cache, up to
E3-1268L v5
3.40GHz, 35W)
7th Gen Intel® Core™ i7-7700 Processor (8M Cache, up to
i7-7700
4.20GHz, 65W)
7th Gen Intel® Core™ i7-7700T Processor (8M Cache, up to
i7-7700T
3.80GHz, 35W)
6th Gen Intel® Core™ i7-6700 Processor (8M Cache, up to
i7-6700
4.00GHz)

iv
Part Number Description
6th Gen Intel® Core™ i7-6700TE Processor (8M Cache, up to
i7-6700TE
3.40GHz)
7th Gen Intel® Core™ i5-7500 Processor (6M Cache, up to
i5-7500
3.80GHz, 65W)
7th Gen Intel® Core™ i5-7500T Processor (6M Cache, up to
i5-7500T
3.30GHz, 35W)
6th Gen Intel® Core™ i5-6500 Processor (6M Cache, up to
i5-6500
3.60GHz)
6th Gen Intel® Core™ i5-6500TE Processor (6M Cache, up to
i5-6500TE
3.30GHz)
7th Gen Intel® Core™ i3-7101E Processor (3M Cache, up to
i3-7101E
3.90GHz, 65W)
7th Gen Intel® Core™ i3-7101TE Processor (3M Cache, up to
i3-7101TE
3.40GHz, 35W)
i3-6100 6th Gen Intel® Core™ i3-6100 Processor (3M Cache, 3.70GHz)

i3-6100TE 6th Gen Intel® Core™ i3-6100TE Processor (4M Cache, 2.70GHz)

DDR4 32G Certified DDR4 32GB 2666MHz RAM

DDR4 16G Certified DDR4 16GB 2400/2133 MHz RAM

DDR4 8G Certified DDR4 8GB 2400/2133 MHz RAM

DDR4 4G Certified DDR4 4GB 2400/2133 MHz RAM

280W, 24V, 85V AC to 264V AC Power Adapter with 3-pin
PWA-280W-WT
Terminal Block (7.62mm pitch), Wide Temperature -30°C to +70°C
180W, 24V, 90V AC to 132V AC/ 180V AC to 264V AC Power
PWA-180W
Adapter with 3-pin Terminal Block, 0°C to +40°C
160W, 24V, 85V AC to 264V AC Power Adapter with 3-pin Terminal
PWA-160W-WT
Block (7.62mm pitch), Wide Temperature -30°C to +70°C
PWA-120W 120W, 24V, 90V AC to 264V AC Power Adapter

VESA Mount VESA Mounting Kit

Rack Mount 2U Rackmount Kit

TMK2-20P-100 Terminal Block 20-pin to Terminal Block 20-pin Cable, 100cm

TMK2-20P-500 Terminal Block 20-pin to Terminal Block 20-pin Cable, 500cm

Terminal Board with One 20-pin Terminal Block Connector and
TMB-TMBK-20P
DIN-Rail Mounting
4G Module Mini PCIe 4G/GPS Module with Antenna

WiFi & Bluetooth WiFi & Bluetooth Module with Antenna

v
Table of Contents
CHAPTER 1 GENERAL INTRODUCTION 1
1.1 Overview 1
1.2 Features 2
1.3 Product Specification 2
1.3.1 Specifications of ECS-9000-9R 2
1.3.2 Specifications of ECS-9000-9GD 5
1.3.3 Specifications of ECS-9000-PoER 7
1.3.4 Specifications of ECS-9000-PoE 10
1.3.5 Specifications of ECS-9000-6FR 12
1.3.6 Specifications of ECS-9000-6F 14
1.3.7 Specifications of ECS-9000-4R 16
1.3.8 Specifications of ECS-9000-4G 19
1.3.9 Specifications of ECS-9000-2R 21
1.3.10 Specifications of ECS-9000-2G 23
1.4 Supported CPU List 26
1.5 Mechanical Dimension 27
1.5.1 Dimensions of ECS-9000-9R 27
1.5.2 Dimensions of ECS-9000-9GD 27
1.5.3 Dimensions of ECS-9000-PoER 27
1.5.4 Dimensions of ECS-9000-PoE 28
1.5.5 Dimensions of ECS-9000-6FR 28
1.5.6 Dimensions of ECS-9000-6F 28
1.5.7 Dimensions of ECS-9000-4R 29
1.5.8 Dimensions of ECS-9000-4G 29
1.5.9 Dimensions of ECS-9000-2R 29
1.5.10 Dimensions of ECS-9000-2G 30

CHAPTER 2 GETTING TO KNOW YOUR ECS-9000 31

2.1 Packing List 31
2.2 Front Panel I/O Functions 32
2.3 Rear Panel I/O and Functions 39
2.4 Main Board Expansion Connectors 44

vi
 2.5 Main Board Jumper & DIP Switch Settings 55
2.6 Ignition Control 58

CHAPTER 3 SYSTEM SETUP 61

3.1 How to Open Your ECS-9000 61
3.2 Installing CPU 65
3.3 Installing DDR4 SO-DIMM Modules 68
3.4 Installing Mini PCIe Card 69
3.5 Installing Antenna Cable 70
3.6 Installing CFast Card 71
3.7 Installing SIM Card 73
3.8 Installing SSD/HDD 75
3.9 Mounting Your ECS-9000 79

CHAPTER 4 BIOS SETUP 85

4.1 BIOS Settings 85
4.2 Main 86
4.3 Advanced 86
4.4 Chipset 95
4.5 Security 100
4.6 Boot 101
4.7 Save & Exit 102

APPENDIX A : Isolated DIO Guide 103

APPENDIX B : Software Functions 109
APPENDIX C : RAID Functions 113
APPENDIX D : Power Consumption 117
APPENDIX E : Supported Memory & Storage List  121
APPENDIX F : Install Win11 (BIOS TPM Setting) 124

vii
1
GENERAL INTRODUCTION
1.1 Overview
Vecow ECS-9000 Series is an all-in-one integrated Fanless Embedded
Workstation System. LGA1151 Socket supports Quad Core 6th Generation Intel®
Xeon®/Core™ i7/i5/i3 processor (Kaby Lake/Skylake) running with workstation-
grade Intel® C236 chipset, dual channel DDR4 2400MHz up to 64GB ECC
memory, advanced Intel® HD Graphics P630/630/P530/530 supporting DirectX
12, OpenGL 4.4 and OpenCL 2.0 API, onboard DVI-I, DVI-D and DisplayPort
display interface for Ultra HD 4K resolution, ECS-9000 offers new generation
CPU performance, power efficiency, and graphics performance; PCIe 3.0 (8GT/
s), Multiple SATA III (6Gbps), USB 3.0 (5Gbps), PoE (1Gbps) LAN and multiple
wireless connections make seamless high-speed data conveying possible.
Vecow ECS-9000 Series Fanless Embedded System delivers outstanding
system performance and power productivity for demanding workloads in real-
time mission critical embedded computing applications.

All-in-one and cable-less designs, fanless -40°C to 75°C operating temperature,

6 GigE LAN ports with 4 IEEE 802.3at (25.5W/48V) PoE+ without additional
power connections, 2 Front-access 2.5” SSD/HDD trays, up to 6 SIM card
sockets for WiFi/4G/3G/LTE/GPRS/UMTS, 1 Front-access CFast socket, 2
SATA III supports software RAID function, 6 external USB 3.0, 4 COM RS-
232/422/485, up to 6 Mini PCIe expansions, 16 Isolated DIO, 6V to 36V wide
range power input with 80V surge protection, configurable ignition power control,
smart remote management features, remote power switch, EN50155 and
EN50121-3-2 compliant, optional supports full function SUMIT A, B expansion
for multiple 10G LAN/10G SPF+ Fiber connections, Vecow ECS-9000 Series
Fanless Embedded System serves new-generation integration for rugged
embedded applications.

With outstanding system performance, leading integrated features, smart

manageability, flexible expandability, excellent mobile availability, secure
power protection and more rugged reliability, Vecow ECS-9000 Series Fanless
Embedded System is your superb solution for Machine Vision, Intelligent
Automation, Smart Manufacturing, Embedded Cloud, Intelligent Surveillance,
Vehicle Computing, Mobile Robot Control, and any performance-driven real-time
Industry 4.0 applications in harsh environments.

GENERAL INTRODUCTION 1
 1.2 Features
• LGA 1151 Socket supports Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S) with Intel® C236 Chipset
• Fanless, -40°C to 75°C Operating Temperature
• 2 DDR4 2400/2133 MHz Memory, up to 64GB
• Up to 9 GigE LAN with 4 IEEE 802.3at PoE+, iAMT 11.0 supported (Optional)
• 6 Independent GigE LAN with 2 SFP, iAMT 11.0 supported (Optional)
• DVI-I, DVI-D and DisplayPort display interface, up to 4K display
• 3 Mini PCIe Slot, 4 COM, 6 USB 3.0
• 3 External SIM Card Socket support WiFi/4G/3G/LTE/GPRS/UMTS
• Up to 2 Front-access 2.5" HDD/SSD Tray, 1 Front-access CFast Socket
• Full function SUMIT A, B expansion (Optional)
• 16 Isolated DIO (Optional)
• 6V to 36V DC Power Input with 80V Surge Protection
• Configurable Ignition Power Control

1.3 Product Specification

1.3.1 Specifications of ECS-9000-9R

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
Isolated DIO 16 Isolated DIO (8 DI, 8 DO)
LED Power, HDD, Wireless, PoE
SIM Card 3 SIM Card Socket (External)

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 2

Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz
Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 Front-access 2.5" SSD/HDD Tray
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out
Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
LAN 7 Intel® 82574L GigE LAN
LAN 8 Intel® 82574L GigE LAN
LAN 9 Intel® 82574L GigE LAN
PoE
LAN 3 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 4 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 5 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 6 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power

GENERAL INTRODUCTION 3
 Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 4

1.3.2 Specifications of ECS-9000-9GD
System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
Isolated DIO 16 Isolated DIO (8 DI, 8 DO)
LED Power, HDD, Wireless, PoE
SIM Card 3 SIM Card Socket (External)
Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz
Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 2.5” SSD/HDD Bracket (Internal)
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out

GENERAL INTRODUCTION 5
 Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
LAN 3 Intel® I210 GigE LAN
LAN 4 Intel® I210 GigE LAN
LAN 5 Intel® I210 GigE LAN
LAN 6 Intel® I210 GigE LAN
PoE
LAN 3 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 4 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 5 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 6 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power
Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 6

 Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

1.3.3 Specifications of ECS-9000-PoER

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
Isolated DIO 16 Isolated DIO (8 DI, 8 DO)
LED Power, HDD, Wireless, PoE
SIM Card 3 SIM Card Socket (External)

GENERAL INTRODUCTION 7
 Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
SUMIT A, B 2 SUMIT Slot (Optional)
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz
Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 Front-access 2.5" SSD/HDD Tray
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out
Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
PoE
LAN 3 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 4 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 5 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 6 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 8

Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

GENERAL INTRODUCTION 9
 1.3.4 Specifications of ECS-9000-PoE

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
Isolated DIO 16 Isolated DIO (8 DI, 8 DO)
LED Power, HDD, Wireless, PoE
SIM Card 3 SIM Card Socket (External)
Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
SUMIT A, B 2 SUMIT Slot (Optional)
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz
Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 2.5" SSD/HDD Bracket (Internal)
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 10

Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
PoE
LAN 3 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 4 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 5 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
LAN 6 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power
Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)

GENERAL INTRODUCTION 11
 Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

1.3.5 Specifications of ECS-9000-6FR

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
GPIO 16 GPIO
LED Power, HDD, Wireless
SIM Card 3 SIM Card Socket (External)
Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 12

Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 Front-access 2.5" SSD/HDD Tray
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out
Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
LAN 3 Intel® I210 GigE LAN
LAN 4 Intel® I210 GigE LAN
LAN 5 Intel® I350 GigE LAN supports SFP+
LAN 6 Intel® I350 GigE LAN supports SFP+
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power
Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)

GENERAL INTRODUCTION 13
 Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

1.3.6 Specifications of ECS-9000-6F

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
GPIO 16 GPIO
LED Power, HDD, Wireless
SIM Card 3 SIM Card Socket (External)
Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 14

Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz
Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 2.5" SSD/HDD Bracket (Internal)
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out
Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
LAN 3 Intel® I210 GigE LAN
LAN 4 Intel® I210 GigE LAN
LAN 5 Intel® I350 GigE LAN supports SFP+
LAN 6 Intel® I350 GigE LAN supports SFP+
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power
Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux

GENERAL INTRODUCTION 15
 Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

1.3.7 Specifications of ECS-9000-4R

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 16

I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
GPIO 16 GPIO
LED Power, HDD, Wireless
SIM Card 3 SIM Card Socket (External)
Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
SUMIT A, B 2 SUMIT Slot (Optional)
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz
Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 Front-access 2.5" SSD/HDD Tray
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out
Audio Interface 1 Mic-in, 1 Line-out
Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
LAN 3 Intel® I210 GigE LAN
LAN 4 Intel® I210 GigE LAN
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin

GENERAL INTRODUCTION 17
 Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power
Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 18

1.3.8 Specifications of ECS-9000-4G

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
GPIO 16 GPIO
LED Power, HDD, Wireless
SIM Card 3 SIM Card Socket (External)
Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
SUMIT A, B 2 SUMIT Slot (Optional)
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz
Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 2.5" SSD/HDD Bracket (Internal)
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out

GENERAL INTRODUCTION 19
 Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
LAN 3 Intel® I210 GigE LAN
LAN 4 Intel® I210 GigE LAN
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power
Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 20

 Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

1.3.9 Specifications of ECS-9000-2R

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
GPIO 16 GPIO
LED Power, HDD, Wireless
SIM Card 3 SIM Card Socket (External)
Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
SUMIT A, B 2 SUMIT Slot (Optional)
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz

GENERAL INTRODUCTION 21
 Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 Front-access 2.5" SSD/HDD Tray
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out
Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power
Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 22

 Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

1.3.10 Specifications of ECS-9000-2G

System
Processor Quad Core Intel® Xeon®/Core™ i7/i5/i3 Processor
(Kaby Lake-S/Skylake-S)
Chipset Intel® C236
BIOS AMI
SIO IT8786E
Memory • DDR4 2400/2133 MHz
• Up to 64GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial 4 COM RS-232/422/485 w/auto flow control
USB • 6 USB 3.0 (External)
• 1 USB 3.0 (Internal)
GPIO 16 GPIO
LED Power, HDD, Wireless
SIM Card 3 SIM Card Socket (External)

GENERAL INTRODUCTION 23
 Expansion
Mini PCIe 3 Mini PCIe Socket :
• 2 Full-size for PCIe/USB/External SIM Card/mSATA
• 1 Half-size for PCIe/USB 3.0/External SIM Card
SUMIT A, B 2 SUMIT Slot (Optional)
Graphics
Graphics Processor Intel® HD Graphics P630/630/P530/530
Interface • DVI-I : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort : Up to 4096 x 2304 @ 60Hz
Storage
SATA 2 SATA III (6Gbps)
mSATA 2 SATA III (Mini PCIe Type, 6Gbps)
SATA DOM 1 SATA II (3Gbps)
Storage Device • 1 CFast Socket, Push-in/Push-out Ejector
• 2 2.5" SSD/HDD Bracket (Internal)
Audio
Audio Codec Realtek ALC888S-VD, 7.1 Channel HD Audio
Audio Interface 1 Mic-in, 1 Line-out
Ethernet
LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0
LAN 2 Intel® I210 GigE LAN
Power
Input Voltage 6V to 36V, DC-in
Power Interface • 3-pin Terminal Block : V+, V-, Frame Ground
• Mini-DIN 4-pin
Ignition Control 16 Mode (Internal)
Remote Switch 3-pin Terminal Block : On, Off, IGN
Surge Protection Up to 80V/1ms Transient Power
Others
TPM Optional Infineon SLB9665 supports TPM 2.0, LPC
interface
Watchdog Timer Reset : 1 to 255 sec./min. per step
Smart Management Wake on LAN, PXE supported
HW Monitor Monitoring temperature, voltages. Auto throttling control
when CPU overheats.

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 24

Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 175mm x 79mm (10.24" x 6.89" x 3.11")
Weight 3.8 kg (8.38 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature 35W TDP CPU :
Core™ i7, i5, i3 : -40°C to 75°C (-40°F to 167°F)
Xeon® E3-1268L v5 : -40°C to 70°C (-40°F to 158°F)
65W TDP CPU :
Core™ i7, i5, i3 : -40°C to 55°C (-40°F to 131°F)
80W TDP CPU :
Xeon® E3-1275 v6, E3-1275 v5, E3-1225 v5 : -40°C to
45°C (-40°F to 113°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5% to 95% Humidity, non-condensing
Relative Humidity 95% at 75°C
Shock • IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
Vibration • IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
EMC E13, CE, FCC, EN50155, EN50121-3-2

GENERAL INTRODUCTION 25
 1.4 Supported CPU List
Processor No. TDP Cache Max. Frequency Embedded

Intel® Xeon® E3-1275 v6 80W 8M Up to 4.20 GHz Y

Intel® Xeon® E3-1275 v5 80W 8M Up to 4.00 GHz Y

Intel® Xeon® E3-1225 v5 80W 8M Up to 3.70 GHz Y

Intel® Xeon® E3-1268 v5 35W 8M Up to 3.40 GHz Y

Intel® Core™ i7-7700 65W 8M Up to 4.20 GHz Y

Intel® Core™ i7-7700T 35W 8M Up to 3.80 GHz Y

Intel® Core™ i7-6700 65W 8M Up to 4.00 GHz Y

Intel® Core™ i7-6700TE 35W 8M Up to 3.40 GHz Y

Intel® Core™ i5-7500 65W 6M Up to 3.80 GHz Y

Intel® Core™ i5-7500T 35W 6M Up to 3.30 GHz Y

Intel® Core™ i5-6500 65W 6M Up to 3.60 GHz Y

Intel® Core™ i5-6500TE 35W 6M Up to 3.30 GHz Y

Intel® Core™ i3-7101E 65W 3M Up to 3.90 GHz Y

Intel® Core™ i3-7101TE 35W 3M Up to 3.40 GHz Y

Intel® Core™ i3-6100 65W 4M Up to 3.70 GHz Y

Intel® Core™ i3-6100TE 35W 4M Up to 2.70 GHz Y

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 26

1.5 Mechanical Dimension
1.5.1 Dimensions of ECS-9000-9R
297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)

175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)
Unit: mm (inch)

1.5.2 Dimensions of ECS-9000-9GD

297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)

175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)

Unit: mm (inch)

1.5.3 Dimensions of ECS-9000-PoER

297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)
175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)

Unit: mm (inch)

GENERAL INTRODUCTION 27
 1.5.4 Dimensions of ECS-9000-PoE
297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)

175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)
Unit: mm (inch)

1.5.5 Dimensions of ECS-9000-6FR

297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)

175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)

Unit: mm (inch)

1.5.6 Dimensions of ECS-9000-6F

297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)
175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)

Unit: mm (inch)

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 28

1.5.7 Dimensions of ECS-9000-4R
297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)

175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)
Unit: mm (inch)

1.5.8 Dimensions of ECS-9000-4G

297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)

175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)

Unit: mm (inch)

1.5.9 Dimensions of ECS-9000-2R

297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)
175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)

Unit: mm (inch)

GENERAL INTRODUCTION 29
 1.5.10 Dimensions of ECS-9000-2G
297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)

175.0 (6.89”)
115.0 (4.53”)
79.1 (3.11”)
Unit: mm (inch)

©Vecow ECS-9000 User Manual GENERAL INTRODUCTION 30

2
GETTING TO KNOW YOUR ECS-9000
2.1 Packing List
Item Description Qty
1 ECS-9000 Fanless Embedded System (According to the 1
configuration of you order, the ECS-9000 series may contain
SSD/HDD and DDR4 SO-DIMM. Please verify these items if
necessary.)
2 ECS-9000-9GD/PoE/6F/4G/2G accessory box, which contains
● Wall-mounting bracket 2
● KHS#6-32x6 screw for wall-mounting bracket 8
● M2.5x6 screw for Mini PCIe Slot 3
● Din-Rail-PH-Mx16.5-S-Ni 4
● 3-pin pluggable terminal block 2
● 20-pin pluggable terminal block 1
● Foot Pad 4
● SSD/HDD Bracket KH-M3x6L Ni 8
● SATA cable 1
3 ECS-9000-9R/PoER/6FR/4R/2R accessory box, which contains
● Wall-mounting bracket 2
● KHS#6-32x6 screw for wall-mounting bracket 8
● M2.5x6 screw for Mini PCIe Slot 3
● Din-Rail-PH-M4x16.5-S-Ni 4
● 3-pin pluggable terminal block 2
● 20-pin pluggable terminal block 1
● Foot Pad 4
● SSD/HDD Tray Key 2

GETTING TO KNOW YOUR ECS-9000 31

 2.2 Front Panel I/O Functions
In Vecow ECS-9000 series family, all I/O connectors are located on front panel
and rear panel. Most of the general connections to computer device, such as
USB, LAN Jack, Display, DVI-D, Display Port and any additional storage, are
placed on the front panel.

2.2.1 Reset Tact Switch

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

It is a hardware reset switch. Use this switch to reset the system without power
off the system. Press the Reset Switch for a few seconds, then reset will be
enabled.

2.2.2 Power Button

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

The Power Button is a non-latched switch with dual color LED indication. It
indicates power status: S0, S3 and S5. More detail LED indications are listed as
follows:
LED Color Power Status System Status
Solid Blue S0 System working

Solid Orange S3, S5 Suspend to RAM, System off with standby power

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 32

To power on the system, press the power button and then the blue LED is
lightened. To power off the system, you can either command shutdown by OS
operation, or just simply press the power button.

If system error, you can just press the power button for 4 seconds to shut down
the machine directly. Please do note that a 4-second interval between each
2 power-on/ power-off operation is necessary in normal working status. (For
example, once turning off the system, you have to wait for 4 seconds to initiate
another power-on operation).

2.2.3 CFast Card

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

There is a CFast socket on the front panel supporting Type-I/II Compact

Flash card. It is implemented by a SATA III Port from CM236 PCH. Be sure
to disconnect the power source and unscrew the CFast socket cover before
installing a CFast card. The ECS-9000 does not support the CFast hot swap
and PnP (Plug and Play) functions. It is necessary to remove power source first
before inserting or removing the CFast card.

The pinouts of CFast port are listed as follows:

Pin No. Description Pin No. Description
S1 GND PC6 NC
S2 SATA_TXP5 PC7 GND
S3 SATA_TXN5 PC8 CFAST_LED
S4 GND PC9 NC
S5 SATA_RXN5 PC10 NC
S6 SATA_RXP5 PC11 NC
S7 GND PC12 NC
PC1 GND PC13 +3.3V
PC2 GND PC14 +3.3V
PC3 NC PC15 GND
PC4 NC PC16 GND
PC5 NC PC17 NC

GETTING TO KNOW YOUR ECS-9000 33

 2.2.4 PWR and HDD LED Indicator

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

HDD LED/Yellow: A Hard Disk/CFast LED. If the LED is on, it indicates that the
system’s storage is functional. If it is off, it indicates that the system’s storage is
not functional. If it is flashing, it indicates data access activities.

Power LED/Green: If the LED is solid green, it indicates that the system is
powered on.
LED Color Power Status System Status
• On/Off : Storage status, function or not.
Yellow HDD/CFast
• Twinkling : Data transferring.

Green Power System power status (On/Off)

2.2.5 DVI-D Connector

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

The DVI-D connector on the front panel supports DVI display. This connector
can either output DVI signal. The DVI output mode supports up to 1920 x 1200
resolution and output mode supports up to 1920 x 1200 resolution. The DVI is
automatically selected according to the display device connected. You will need
a DVI-D cable when connecting to a display device.

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 34

2.2.6 DVI-I Connector

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

The DVI-I connector on the front panel supports both DVI and VGA display
modes. This connector can output DVI signals. The DVI output mode supports
up to 1920 x 1200 resolution. The DVI mode is automatically selected according
to the display device connected. You will need a DVI-I cable when connecting to
a display device. The VGA output mode supports up to 1920 x 1200 resolution.
If use VGA function will need a DVI-I to VGA module connecting to DVI-I device.
Below is the DVI-I to VGA module picture:

2.2.7 DisplayPort

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

Onboard Display Port support auxiliary channel dual mode, connection supports
up to 4096 x 2304 resolution at 60Hz.

GETTING TO KNOW YOUR ECS-9000 35

 2.2.8 USB 3.0

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

There are 4 USB 3.0 connections available supporting up to 5GB per second
data rate in the front side of ECS-9000. It also compliant with the requirements
of Super Speed (SS), high speed (HS), full speed (FS) and low speed (LS).

2.2.9 WLAN LED, Mini PCIe, SIM Card Comparison

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

Mini PCIe Slot/SIM Slot/WLAN LED Mapping Table :

Mini PCIe SIM LED

Mini PCIe 1 SIM 1 (CN9) 1

Mini PCIe 2 SIM 2 (CN10) 2 SIM 1 SIM 2

SIM3
Mini PCIe 3 SIM 3 (CN11) 3

Mini PCIe 1

Mini PCIe 2
Mini PCIe 3

CN11

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 36

 CN10 CN9

Note:
The SIM card sockets do not support hot-plug. Please make sure to unplug the
system power before inserting the SIM card(s).

2.2.9 Ethernet Port

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

There are 2 8-pin RJ-45 jacks supporting 10/100/1000 Mbps Ethernet

connections in the front side. LAN 1 is powered by Intel i219 Ethernet Phy; LAN
2 is powered by Intel I210 Ethernet engine. When both LAN 1 and LAN 2 work
in normal status, iAMT 11.0 function is enabled.

Using suitable RJ-45 cable, you can connect the system to a computer, or to
any other devices with Ethernet connection, for example, a hub or a switch.
Moreover, both of LAN 1 and LAN 2 supports Wake on LAN and Pre-boot
functions. The pin-outs of LAN 1 and LAN 2 are listed as follows:

Pin No. 10/100 Mbps 1000Mbps

1 E_TX+ MDI0_P

2 E_TX- MDI0_N

3 E_RX+ MDI1_P

4 ---- MDI2_P

5 ----- MDI2_N

6 E_RX- MDI1_N

7 ----- MDI3_P

8 ------ MDI3_N

GETTING TO KNOW YOUR ECS-9000 37

 Each LAN port is supported by standard RJ-45 connector with LED indicators
to present Active/Link/Speed status of the connection. The LED indicator on the
right bottom corner lightens in solid green when the cable is properly connected
to a 100 Mbps Ethernet network; The LED indicator on the right bottom corner
lightens in solid orange when the cable is properly connected to a 1000Mbps
Ethernet network; The left LED will keep twinkling/ off when Ethernet data
packets are being transmitted/ received.

10Mbps 100Mbps 1000Mbps

1 8

Right Solid Solid

Off
Bottom Led Green Orange

Left Flash Flash Flash

Bottom Led Yellow Yellow Yellow

2.2.11 Audio Connector

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

There are 2 audio connectors, Mic-in and Line-out, in the front side of ECS-9000.
Onboard Realtek ALC888S-VD audio codec supports 7.1 channel HD audio
and fully complies with Intel® High Definition Audio (Azalia) specifications. To
utilize the audio function in Windows platform, you need to install corresponding
drivers for both Intel CM236 chipset and Realtek ALC888S-VD codec.

2.2.12 SSD/HDD Tray

Reset SIM 1 SIM 2 HDD DP DVI-D LAN 2 LAN 1

1 2 3
WLAN SIM 3
CFast

PWR DVI-I

There are 2 front-access 2.5” SSD/HDD trays in the front side of ECS-9000.
Just trigger to open the SSD/HDD tray, up to 4TB is available.

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 38

2.3 Rear Panel I/O and Functions
2.3.1 Power Terminal Block

PoE+ PoE+ DIO DC-IN

3 4 5 6 COM 1 COM 3 20 Isolated 11

10 1
PIN 1 ~ 8 DI PIN 11 ~ 18 DO
COM 2 COM 4

LAN 3 LAN 5
LAN 4 LAN 6
IGN On / Off
Power Switch

This system supports 6V to 36V DC power input by terminal block in the rear
side. In normal power operation, power LED lightens in solid green. Supports up
to 80V surge protection.
Pin No. Definition Pin No. Definition

1 V+ 2 V-

3 Chassis Ground

2.3.2 Remote Power On/Off Switch & Ignition

PoE+ PoE+ DIO DC-IN

3 4 5 6 COM 1 COM 3 20 Isolated 11

10 1
PIN 1 ~ 8 DI PIN 11 ~ 18 DO
COM 2 COM 4

LAN 3 LAN 5
LAN 4 LAN 6
IGN On / Off
Power Switch

It is a 2-pin power-on or power-off switch through Phoenix Contact terminal

block. You could turn on or off the system power by using this contact. This
terminal block supports dual function of soft power-on/ power-off (instant off or
delay 4 second), and suspend mode.

Pin No. Definition Pin No. Definition

1 Ignition 2 External Power Button V+

3 External Power Button V-

GETTING TO KNOW YOUR ECS-9000 39

 2.3.3 Isolated DIO/GPIO
2.3.3.1 Isolated DIO

PoE+ PoE+ DIO DC-IN

3 4 5 6 COM 1 COM 3 20 Isolated 11

10 1
PIN 1 ~ 8 DI PIN 11 ~ 18 DO
COM 2 COM 4

LAN 3 LAN 5
LAN 4 LAN 6
IGN On / Off
Power Switch

There is a 16-bit (8-bit DI, 8-bit DO) connectors in the rear side. DI/DIO supports
NPN (Sink) and PNP (Source) mode. Each DI channel is equipped with a
photocouper for isolated protection. Each DO with isolator chip, Config by a
Jumper for each DIO connector. DO Safety-Related Certifications:
• 4242-VPK Basic Isolation per DIN V VDE V 0884-10 DIO
and DIN EN 61010-1 20 Isolated 11
• 3-KVRMS Isolation for 1 minute per UL 1577
• CSA Component Acceptance Notice 5A, IEC
60950-1 and IEC 61010-1 End Equipment Standards 10 1
• GB4943.1-2011 CQC Certified PIN 1 ~ 8 D I PIN 11 ~ 18 DO

DIO connectors pin out:

DIO Pin No. Definition Function
1 INPUT 0 SIO_GPI80
2 INPUT 1 SIO_GPI81
3 INPUT 2 SIO_GPI82
4 INPUT 3 SIO_GPI83
5 INPUT 4 SIO_GPI84
6 INPUT 5 SIO_GPI85
7 INPUT 6 SIO_GPI86
8 INPUT 7 SIO_GPI87
9 DI1_COM -
DIO 10 DIO1_GND -
11 OUTPUT 0 SIO_GPO70
12 OUTPUT 1 SIO_GPO71
13 OUTPUT 2 SIO_GPO72
14 OUTPUT 3 SIO_GPO73
15 OUTPUT 4 SIO_GPO74
16 OUTPUT 5 SIO_GPO75
17 OUTPUT 6 SIO_GPO76
18 OUTPUT 7 SIO_GPO77
19 DIO1_GND -
20 DIO1_VDC (6~48V Input) -

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 40

Sink Mode (NPN) Power DIO Connector
Supply V+ DI_COM (Pin 9)
6-48V DC
V-

DI (Pin1-8)

Source Mode (PNP) Power DIO Connector

Supply V+ DI_COM (Pin 9)
6-48V DC
V-

DI (Pin1-8)

DO Reference Circuit:
Sink Mode Device DIO Connector
(NPN, Default) 6-48V DC
V+ DIO_VDC (Pin 20)

IO DO (Pin11-18)

V- DIO_GND (Pin10,19)

Source Mode (PNP) Device DIO Connector

6-48V DC
V+ DIO_VDC (Pin 20)

IO DO (Pin11-18)

V- DIO_GND (Pin10,19)

2.3.3.2 GPIO
The system offers sixteen programmable I/O .
If the GPIO is logic high, it indicates that the mapping SIO GPIO pin is logic high
level. If the GPIO is logic low, it indicates that the mapping SIO GPIO pin is logic
low level. GPIO Connectors pin assignments :

Pin No. Definition Pin No. Definition

1 SIO_GPI70 11 SIO_GPO80

2 SIO_GPI71 12 SIO_GPO81

3 SIO_GPI72 13 SIO_GPO82

4 SIO_GPI73 14 SIO_GPO83

5 SIO_GPI74 15 SIO_GPO84

6 SIO_GPI75 16 SIO_GPO85

7 SIO_GPI76 17 SIO_GPO86

8 SIO_GPI77 18 SIO_GPO87

9 ----------- 19 -----------

10 ----------- 20 -----------

GETTING TO KNOW YOUR ECS-9000 41

 2.3.4 Serial Port

PoE+ PoE+ DIO DC-IN

3 4 5 6 COM 1 COM 3 20 Isolated 11

10 1
PIN 1 ~ 8 DI PIN 11 ~ 18 DO
COM 2 COM 4

LAN 3 LAN 5
LAN 4 LAN 6
IGN On / Off
Power Switch

Serial port 1 to 4 (COM 1 to 4) can be configured for RS-232, RS-422, or RS-

485 with auto flow control communication. The default definition of COM 1 and
COM 2 is RS-232, if you want to change to RS-422 or RS-485, you can find the
setting in BIOS.

BIOS Setting Function

RS-232
COM 1
RS-422 (5-wire)
COM 2
RS-422 (9-wire)
COM 3
RS-485
COM 4
RS-485 w/z auto-flow control

The pin assignments are listed in the table as follow :

Serial Pin No. RS-232 RS-422 RS-422 RS-485

Port (5-wire) (9-wire) (3-wire)

1 DCD TXD- TXD- DATA-

2 RXD TXD+ TXD+ DATA+

3 TXD RXD+ RXD+ -----------

4 DTR RXD- RXD- -----------

1 to 4
5 GND GND GND GND

6 DSR ----------- RTS- -----------

7 RTS ----------- RTS+ -----------

8 CTS ----------- CTS+ -----------

9 RI ----------- CTS- -----------

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 42

2.3.5 PoE (Power over Ethernet) Ports

PoE+ PoE+ DIO DC-IN

3 4 5 6 COM 1 COM 3 20 Isolated 11

10 1
PIN 1 ~ 8 DI PIN 11 ~ 18 DO
COM 2 COM 4

LAN 3 LAN 5
LAN 4 LAN 6
IGN On / Off
Power Switch

There are 4 RJ45 connectors in the rear side of ECS-9000. It supports IEEE
802.3at (PoE+) Power over Ethernet (PoE) connection delivering up to 37W/
54V per port and 1000BASE-T GigE data signals over standard Ethernet Cat
5/Cat 6 cable. Each PoE connection is powered by Intel® I210 GigE Ethernet
controller and independent PCI express interface to connect with multi-core
processor for network and data transmit optimization. Only when PoE port starts
to supply power to power devices, the dedicated LED will be lightened.
PS. Suggest to use PoE function when power input is over 12V.

The pin-outs of LAN 1 and LAN 2 are listed as follows:

Pin No. 10/100 Mbps 1000Mbps PoE
1 E_TX+ MDI0_P PoE+
2 E_TX- MDI0_N PoE+
3 E_RX+ MDI1_P PoE-
4 ---- MDI2_P ----
5 ----- MDI2_N ----
6 E_RX- MDI1_N PoE-
7 ----- MDI3_P ----
8 ------ MDI3_N ----

Each LAN port is supported by standard RJ-45 connector with LED indicators to
present Active/Link/Speed status of the connection.

The LED indicator on the right bottom corner lightens in solid green when the
cable is properly connected to a 100Mbps Ethernet network; The LED indicator
on the right bottom corner lightens in solid orange when the cable is properly
connected to a 1000Mbps Ethernet network; The left LED will keep twinkling/ off
when Ethernet data packets are being transmitted/received.
1 8
LED Status 10Mbps 100Mbps 1000Mbps

Right Solid Solid

Off
Bottom Led Green Orange

Left Flash Flash Flash

Bottom Led Yellow Yellow Yellow

GETTING TO KNOW YOUR ECS-9000 43

 PoE LED LED Color PoE Status

LED 3 - 6 Solid Green PoE On

2.4 Main Board Expansion Connectors

2.4.1 Top View of ECS-9000 Main Board With Connector Location

M2 CN1 JP9

J6 JP8

J7 JP3 JP4 JP6 JP5

JP7 J3

J4
FAN1 CN14 SATA2 SATA1

JP1 JP2

Battery

Mini PCIe 1
SATA3 SUMITB

CN37

SODIMM 2 SODIMM 1 BIOS

Mini PCIe 2
Mini PCIe 3

J1 CN11
SUMITA

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 44

2.4.2 Bottom View of ECS-9000 Main Board With Connector Location

CN10 CN9

2.4.3 Miscellaneous Pin Header

2.0mm 2x4p header
This pin header can be used as a backup for following functions, hard drive
LED indicator, reset button, power LED indicator, and power-on/off button,
which already can be accessed by front panel and top panel. The pin-outs of
Miscellaneous port are listed in following table:

J1

Group Pin No. Description

1 HDD_LED_P
HDD LED
3 HDD_LED_N

GETTING TO KNOW YOUR ECS-9000 45

 5 FP_RST_BTN_N
RESET BUTTON
7 Ground

2 PWR_LED_P
POWER LED
4 PWR_LED_N

6 FP_PWR_BTN_IN
POWER BUTTON
8 Ground

2.4.4 SATA III Connector

There are 3 onboard high performance Serial ATA III (SATA III) on ECS-9000.
It supports higher storage capacity with less cabling effort and smaller required
space.

SATA2 SATA1

SATA3

The pin assignments of SATA1 and SATA2 , SATA3 are listed in the following
table:
Pin No. Definition Pin No. Definition

1 GND 5 RXN

2 TXP 6 RXP

3 TXN 7 GND

4 GND

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 46

2.4.5 SATA Power Connector
The ECS-9000 also equip with a SATA power connector. The one port supports
5V (up to 2A) and 12V (up to 2A) current to the hard drive or SSD.

J3

J4

The pin assignments of J3, J4 are listed in the following table:

Pin No. Definition Pin No. Definition

1 +12V 3 GND

2 GND 4 +5V

2.4.6 Internal USB

CN14

The USB 3.0 connections available supporting up to 5GB per second data rate.
It also compliant with the requirements of SuperSpeed (SS), Hgh Speed (HS),
Full Speed (FS) and Low Speed (LS). The pin assignments of CN14 are listed
in the following table:

Connector Pin No. Description Pin No. Description

1 USB_VCC 6 StdA_SSRX+

2 USBD- 7 GND_DRAIN
CN12 3 USBD+ 8 StdA_SSTX−

4 GND 9 StdA_SSTX+

5 StdA_SSRX−

GETTING TO KNOW YOUR ECS-9000 47

 2.4.7 DDR4 Slot
There are 2 DDR4 channel onboard, support DDR4 2400/2133, max 64GB,
each channel 32GB

SODIMM 2 SODIMM 1

Slot Description Slot Description

SODIMM_1 DDR4 Channel A SODIMM_2 DDR4 Channel B

2.4.8 BIOS Socket

If the BIOS needs to be changed, please contact the Vecow RMA service team.

BIOS

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 48

2.4.9 SUMIT A, SUMIT B
This system have standard SUMIT A and SUMIT B for SUMIT type add on cards.

SUMITB

SUMITA

SUMIT A Pin Out:

Pin No. Function Pin No. Function

1 +5V_AUX 2 +12V

3 +3.3V 4 SMB_DATA

5 +3.3V 6 XMB_CLK

7 Reserved 8 Reserved

9 Reserved 10 SPI_MISO

11 USB_OC# 12 SPI_MOSI

13 Reserved 14 SPI_CLK

15 +5V 16 SPI_CS10

17 USB_3+ 18 SPI_CS1#

19 USB_3- 20 Reserved

21 +5V 22 LPC_DRQ1#

23 USB_2+ 24 LPC_AD0

25 USB_2- 26 LPC_AD1

27 +5V 28 LPC_AD2

29 USB_1+ 30 LPC_AD3

31 USB_1- 32 LPC_FRAME#

33 +5V 34 SERIRQ#

35 USB_0+ 36 Reserved

37 USB_0- 38 CLK_33MHz

39 GND 40 GND

GETTING TO KNOW YOUR ECS-9000 49

 41 A_PET_P0 42 A_PER_P0

43 A_PET_N0 44 A_PER_N0

45 GND 46 APRSNT#/A_PE_CLKREQ#

47 PERST# 48 A_CLKP

49 WAKE# 50 A_CLKN

51 +5V 52 GND

SUMIT B Pin Out:

Pin No. Function Pin No. Function

1 GND 2 GND

3 B_PET_P0 4 B_PER_P0

5 B_PET_N0 6 B_PER_N0

7 GND 8 GND

9 C_CLKP 10 B_CLKP

11 C_CLKN 12 B_CLKN

13 CPRSNT#/C_PE_CLKREQ# 14 GND

15 C_PET_P0 16 C_PER_P0

17 C_PET_N0 18 C_PER_N0

19 GND 20 GND

21 C_PET_P1 22 C_PER_P1

23 C_PET_N1 24 C_PER_N1

25 GND 26 GND

27 C_PET_P2 28 C_PER_P2

29 C_PET_N2 30 C_PER_N2

31 GND 32 GND

33 C_PET_P3 34 C_PER_P3

35 C_PET_N3 36 C_PER_N3

37 GND 38 GND

39 PERST# 40 WAKE#

41 Reserved 42 Reserved

43 +5V 44 Reserved

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 50

 45 +5V 46 +3.3V

47 +5V 48 +3.3V

49 +5V 50 +3.3V

51 +5V 52 +5V_AUX

2.4.10 Mini PCIe

Standard full length Mini PCIe slot:

Mini PCIe 1

Mini PCIe 2
Mini PCIe 3

Pin Out:

Pin No. Function Pin No. Function

51 Reserved 52 +3.3Vaux

49 Reserved 50 GND

47 Reserved 48 +1.5V

45 Reserved 46 Reserved

43 GND 44 Reserved

41 +3.3Vaux 42 Reserved

39 +3.3Vaux 40 GND

37 GND 38 USB_D+

35 GND 36 USB_D-

33 PETp0 34 GND

31 PETn0 32 SMB_DATA

GETTING TO KNOW YOUR ECS-9000 51

 29 GND 30 SMB_CLK

27 GND 28 +1.5V

25 PERn0 26 GND

23 PERp0 24 +3.3Vaux

21 GND 22 PERST#

19 Reserved 20 reserved

17 Reserved 18 GND

Mechanical Key

15 GND 16 UIM_VPP

13 REFCLK+ 14 UIM_RESET

11 REFCLK- 12 UIM_CLK

9 GND 10 UIM_DATA

7 CLKREQ# 8 UIM_PWR

5 Reserved 6 1.5V

3 Reserved 4 GND

1 WAKE# 2 3.3Vaux

2.4.11 RTC Battery

The system’s real-time clock is powered by a lithium battery. It is recommended
that you do not the lithium battery on your own. If the battery needs to be
changed, please contact the Vecow RMA service team.

Battery

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 52

2.4.12 FAN Header
FAN power connector supports for additional thermal requirements. The pin
assignments of FAN 1 are shown in the following diagram:

FN1

Pin out:
Pin No. Function Pin No. Function

1 GND 2 +12V (1.5A max)

3 Fan speed sensor 4 Fan PWM

2.4.13 LPC Port 80 Header

ECS-9000 provides a LPC Port 80 Header for debug card.
CN37

Pin out:
Pin No. Function Pin No. Function

1 SERIRQ 7 LFRAME#

2 +3.3V 8 LAD0

3 LA3 9 N/C

4 RESET# 10 Ground

5 LAD1 11 CLOCK

6 LAD2 12 Ground

GETTING TO KNOW YOUR ECS-9000 53

 2.4.14 Speed LED Header

J6

J7

Pin out:
J6 J7
Pin No. LAN Function Pin No. LAN Function
1 LAN 3 LINK100# 1 LAN 5 LINK100#
2 LAN 4 LINK100# 2 LAN 6 LINK100#
3 LAN 3 LINK1000# 3 LAN 5 LINK1000#
4 LAN 4 LINK1000# 4 LAN 6 LINK1000#
5 LAN 3 ACT# 5 LAN 5 ACT#
6 LAN 4 ACT# 6 LAN 6 ACT#
7 LAN 3 +3V 7 LAN 5 +3V
8 LAN 4 +3V 8 LAN 6 +3V

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 54

2.5 Main Board Jumper & DIP Switch Settings
2.5.1 Top View of ECS-9000 With Jumper and DIP Switch

JP9

JP8

JP3 JP4 JP6 JP5

JP7

CN14

JP1 JP2

SW1

The figure below is the top view of the system board, and it shows the location
of the jumpers and the switches.

You may configure your card to match the needs of your application by setting
jumpers. A jumper is a metal bridge used to close an electric circuit. It consists
of two metal pins and a small metal clip (often protected by a plastic cover) that
slides over the pins to connect them. To “close” a jumper, you connect the pins
with the clip. To “open” a jumper, you remove the clip. Sometimes a jumper will
have three pins, labeled 1, 2, and 3. In this case you would connect either pins
1 and 2, or 2 and 3.

You may configure your card to match the needs of your application by DIP
switch as shown below (the DIP switch on and off)
ON ON ON
1 : OFF 1 : ON 1 : ON
2 : OFF 2 : OFF 2 : ON
1 2 1 2 1 2

GETTING TO KNOW YOUR ECS-9000 55

 2.5.2 USB Power Jumper

JP7

Jumper Setting Function

JP7 2:3 Non Wake Up support
JP7 1:2 Supported Wake Up (Default)

2.5.3 COM Port RI pin Select

JP3 JP4 JP6 JP5

Pin Header Pin No. Description

1-2 +5V (1A max.)

COM 1
3-4 +12V (0.5A max.)
JP3
5-6 RI (Default)

Pin Header Pin No. Description

1-2 +5V (1A max.)

COM 2
3-4 +12V (0.5A max.)
JP4
5-6 RI (Default)

Pin Header Pin No. Description

1-2 +5V (1A max.)

COM 3
3-4 +12V (0.5A max.)
JP5
5-6 RI (Default)

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 56

 Pin Header Pin No. Description

1-2 +5V (1A max.)

COM 4
3-4 +12V (0.5A max.)
JP6
5-6 RI (Default)

2.5.5 PoE Power ON Select

JP8

Jumper Setting Function

JP8 1:2 PoE power on at standby power ready

JP8 2:3 PoE power on after system power on (Default)

2.5.6 CMOS & ME Clear

JP1 JP2

Jumper Setting Function

JP1 1:2 *Normal (Default)

JP1 2:3 Clear CMOS

GETTING TO KNOW YOUR ECS-9000 57

 Jumper Setting Function

JP2 1:2 *Normal (Default)

JP2 2:3 Clear ME

2.6 Ignition Control

ECS-9000 series provides ignition power control feature for in-vehicle
applications. The built-in MCU monitors the ignition signal and turns on/off the
system according to pre-defined on/off delay periods.

2.6.1 Adjust Ignition Control Modes

ECS-9000 series provides 16 modes of different power on/off delay periods
adjustable via SW5 switch. The default rotary switch is set to 0 in ATX/AT power
mode.

SW1

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 58

The modes are listed in the following table:

Item Power on delay Power off delay Switch Position

ON

0 ATX mode 1 2 3 4

ON

1 No delay No delay 1 2 3 4

ON

2 No delay 5 seconds 1 2 3 4

ON

3 No delay 10 seconds 1 2 3 4

ON

4 No delay 20 seconds 1 2 3 4

ON

5 5 seconds 30 seconds 1 2 3 4

ON

6 5 seconds 60 seconds 1 2 3 4

ON

7 5 seconds 90 seconds 1 2 3 4

ON

8 5 seconds 30 minutes
1 2 3 4

ON

9 5 seconds 1 hour 1 2 3 4

ON

A 10 seconds 2 hours 1 2 3 4

ON

B 10 seconds 4 hours 1 2 3 4

ON

C 10 seconds 6 hours 1 2 3 4

ON

D 10 seconds 8 hours 1 2 3 4

ON

E 10 seconds 12 hours 1 2 3 4

ON

F 10 seconds 24 hours
1 2 3 4

GETTING TO KNOW YOUR ECS-9000 59

 2.6.2 Ignition Control Wiring

To activate ignition control, you need to provide IGN signal via the 3-pin
pluggable terminal block located in the back panel. It is below the general wiring
configuration.

V+

Pin No. Definition

IGN
1 Ignition (IGN)

2 External Power S/W +

3 External Power S/W +

For testing purpose, you can refer to the picture above to simulate ignition
signal input controlled by a latching switch.
Note:
1. DC power source and IGN share the same ground.
2. ECS-9000 supports 6V to 36V wide range DC power input in ATX/AT
mode. In Ignition mode, the input voltage is fixed to 12V/24V for car battery
scenario.
3. For proper ignition control, the power button setting should be “Power down”
mode.
In Windows, for
example, you need
to set “When I press
the power button” to
"Shut down."

©Vecow ECS-9000 User Manual GETTING TO KNOW YOUR ECS-9000 60

3
SYSTEM SETUP
3.1 How to Open Your ECS-9000
3.1.1 ECS-9000-R Series

Step 1 Remove front panel six KHS#6-32 screws then pick up front
panel.

Step 2 Remove rear panel five KHS#6-32 screws.

SYSTEM SETUP 61
 Step 3 Remove bottom four F#6-32 screws.

Step 4 Finish.

©Vecow ECS-9000 User Manual SYSTEM SETUP 62

3.1.2 ECS-9000-F/G/PoE Serise

Step 1 Remove front panel six KHS#6-32 screws then pick up front
panel.

Step 2 Remove rear panel five KHS#6-32 screws.

SYSTEM SETUP 63
 Step 3 Remove bottom four F#6-32 (circled in red) and one F-M3 (circled
in yellow) screws.

Step 4 Finish.

©Vecow ECS-9000 User Manual SYSTEM SETUP 64

3.2 Installing CPU
Step 1 Remove one F#6-32 and pick up chock bracket.

Step 2 Remove eleven PH-M3 screws and pick up mother board.

SYSTEM SETUP 65
 Step 3 CPU Socket.

Step 4 Open the cover of CPU Socket. (Be careful CPU pin)

©Vecow ECS-9000 User Manual SYSTEM SETUP 66

Step 5 Match CPU with the CPU socket.

Step 6 Installing CPU on the socket.

Step 7 Close and lock the cover of CPU socket.

SYSTEM SETUP 67
 3.3 Installing DDR4 SO-DIMM Modules
Step 1 Install DDR4 RAM module into SO-DIMM slot.

Step 2 Make sure the RAM module is locked by the memory slot.

©Vecow ECS-9000 User Manual SYSTEM SETUP 68

3.4 Installing Mini PCIe Card
Step 1 Install Mini PCIe card into the Mini PCIe socket.

Step 2 Fasten one M2.5 screw.

SYSTEM SETUP 69
 3.5 Installing Antenna Cable
Step 1 Check antenna cable and washers.

3
1 2

Step 2 Put Antenna cable connector into the hole on rear panel and
fasten the washer 1, washer 2 and washer 3 on Antenna cable
connector.

©Vecow ECS-9000 User Manual SYSTEM SETUP 70

3.6 Installing CFast Card
Step 1 Remove two F-M3x4 screws on CFast Card and SIM Card cover
from the front panel.

Step 2 Remove CFast Card and SIM Card cover.

SYSTEM SETUP 71
 Step 3 Before Inserting CFast & SIM Card, make sure the system power
is not plugged.

Step 4 Insert CFast card and push to lock.

Step 5 Finish.

©Vecow ECS-9000 User Manual SYSTEM SETUP 72

3.7 Installing SIM Card
Step 1 Remove two F-M3x4 screws on CFast Card and SIM Card cover
from the front panel.

Step 2 Remove CFast Card and SIM Card cover.

SYSTEM SETUP 73
 Step 3 Before Inserting CFast & SIM Card, make sure the system power
is not plugged.

Step 4 Insert SIM card and push to lock.

Step 5 Finish.

©Vecow ECS-9000 User Manual SYSTEM SETUP 74

3.8 Installing SSD/HDD
3.8.1 ECS-9000-R Series

Step 1 SSD/HDD tray.

Step 2 Use the trigger and open SSD/HDD tray.

SYSTEM SETUP 75
 Step 3 Installing 2.5” SSD/HDD into the tray.

Step 4 Lock the SSD/HDD tray with key.

©Vecow ECS-9000 User Manual SYSTEM SETUP 76

3.8.2 ECS-9000-F/G/PoE Series

Step 1 Remove F-M3 screw.

Step 2 Install SSD/HDD with HDD bracket.

SYSTEM SETUP 77
 Step 3 Lock KH-M3 screw. (One SSD/HDD with four KH-M3 screws)

Step 4 Installing power and SATA cable with SSD/HDD.

©Vecow ECS-9000 User Manual SYSTEM SETUP 78

3.9 Mounting Your ECS-9000
3.9.1 Wall Mount Bracket

Step 1 Ensure the screw holes on the right and left side of the upper
case match the ones on ECS-9000 wall mount bracket.

SYSTEM SETUP 79
 Step 2 Fasten 4pcs KHS#6-32 screws then finish.

©Vecow ECS-9000 User Manual SYSTEM SETUP 80

3.9.2 VESA Mount

Step 1 ECS-9000 and VESA Mount.

Step 2 Take ECS-9000 and VESA Mount with fasten four KHS#6-32
screws

SYSTEM SETUP 81
 Step 3 Fasten four KHS#6-32 screws and then finish.

Step 4 Finish.

Step 5 ECS-9000 supports 75x75mm (squared in red) and 100x100mm

(squared in yellow).

©Vecow ECS-9000 User Manual SYSTEM SETUP 82

3.9.3 Din Rail Kit

Step 1 ECS-9000 and Din Rail Kit.

Step 2 Take ECS-9000 and VESA Mount with fasten four KHS#6-32
screws

SYSTEM SETUP 83
 Step 3 Fasten four KHS#6-32 screws and then finish.

Step 4 Finish.

Step 5 ECS-9000 With Din Rail.

©Vecow ECS-9000 User Manual SYSTEM SETUP 84

4
BIOS SETUP
4.1 BIOS Settings

Figure 4-1: Entering Setup Screen

BIOS provides an interface for users to check and change system configuration.
The BIOS setup program is accessed by pressing the <Del> key when POST
display output is shown.

BIOS SETUP 85
 4.2 Main

Figure 4-2: BIOS Main Menu

The main menu displays BIOS version and system information. There are two
options on the main menu, system date and system time.

System Date
Set the date. Use <Tab> to switch between date elements.

System Time
Set the time. Use <Tab> to switch between time elements.

4.3 Advanced

Figure 4 3: BIOS Advanced Menu

Select advanced tab to enter advanced BIOS setup options, such as CPU
configuration, SATA configuration, and USB configuration.

©Vecow ECS-9000 User Manual BIOS SETUP 86

4.3.1 ACPI Settings

Figure 4 3-1: ACPI Settings

Enable Hibernation
Enables or Disables system's ability to hibernate (OS/S4 sleep state). This
option may not be effective with some OS.

ACPI Sleep State

Selects the highest ACPI sleep state the system will enter when the SUSPEND
button is pressed.

S3 Video Repost
Enables or Disables S3 video repost.

ACPI Low Power S0 Idle

Enables or Disables ACPI low power S0 idle support.

4.3.2 AMT Configuration

Figure 4 3-2: Intel AMT Settings

Intel AMT
Enables/Disables Intel (R) Active Management Technology BIOS extension.
Note: iAMT H/W is always enabled. This option just controls the BIOS extension
execution. If enabled, this requires additional firmware in the SPI device.

BIOS SETUP 87
 4.3.3 PCH-FW Configuration

Figure 4 3-3: PCH-FW Settings

ME Unconfig on RTC Clear State

Disabling this option will cause ME not to unconfigure on RTC clear.

ME State
Set ME to Soft temporarily Disabled.

4.3.4 SMART Settings

Figure 4 3-4: SMART Settings

SMART Self Test

Run SMART self test on all HDDs during POST.

4.3.5 IT8786 Super IO Configuration

Figure 4-3-5: Super IO Settings

Serial Port 1 Configuration

Set parameters of serial port 1 (COM1).

Serial Port 2 Configuration

Set parameters of serial port 2 (COM2).

©Vecow ECS-9000 User Manual BIOS SETUP 88

Serial Port 3 Configuration
Set parameters of serial port 3 (COM3).

Serial Port 4 Configuration

Set parameters of serial port 4 (COM4).

4.3.6 Hardware Monitor

Figure 4 3-6: Hardware Monitor Settings

The IT8786 SIO features an enhanced hardware monitor providing thermal, fan
speed, and system voltages' status monitoring.

4.3.7 Serial Port Console Redirection

Figure 4 3-7: Serial Port Console Redirection Settings

Console Redirection
Console redirection enable or Disable.

Console Redirection Settings

These settings specify how the host computer and the remote computer (which
the user is using) will exchange data. Both computers should have the same or
compatible settings.

BIOS SETUP 89
 4.3.8 CPU Configuration

Figure 4 3-8: CPU Function Settings

Hyper-threading
Enabled for Windows XP and Linux (OS optimized for Hyper-Threading
Technology) and Disabled for other OS (OS not optimized for Hyper-Threading
Technology). When Disabled, only one thread per core is enabled.

Active Processor Cores

Number of cores to enable in each processor package.

Intel Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided
by Vanderpool Technology.

Hardware Prefetcher
To turn on/off the MLC streamer prefetcher.

Adjacent Cache Line Prefetch

To turn on/off prefetching of adjacent cache lines.

CPU AES
Enable/Disable CPU Advanced Encryption Standard instructions.

Boot performance mode

Select the performance state that the BIOS will set before OS handoff.

Intel(R) SpeedStep(tm)
Allows more than two frequency ranges to be supported.

Turbo Mode
Turbo Mode.
©Vecow ECS-9000 User Manual BIOS SETUP 90
CPU C state
Enable or Disable CPU C states.

Enhanced C-states
Enable/Disable C1E. When enabled, CPU will switch to minimum speed when
all cores enter C-State.

Package C State limit

Package C State limit.

Intel TXT(LT) Support

Enables or Disables Intel (R) TXT (LT) support.

4.3.9 Intel TXT Information

Figure 4 3-9: Intel TXT Information

Display Intel TXT information.

4.3.10 SATA Configuration

Figure 4 3-10: SATA Devices Settings

BIOS SETUP 91
 SATA Controller(s)
Enable or Disable SATA Device.

SATA Mode Selection

Determines how SATA controller(s) operate.

Software Feature Mask Configuration

RAID OROM/RST driver will refer to the SWFM configuration to enable or
Disable the storage features.

Aggressive LPM Support

Enable PCH to aggressively enter link power state.

SATA Controller Speed

Indicates the maximum speed the SATA controller can support.

Options for each SATA port

Port 0
Enable or Disable SATA Port.

SATA Device Type

Identifies that the SATA port is connected to solid state drive or hard disk drive.

4.3.11 Acoustic Management Configuration

Figure 4 3-11: Acoustic Management Settings

Acoustic Management Configuration

Option to enable or Disable automatic acoustic management.

©Vecow ECS-9000 User Manual BIOS SETUP 92

4.3.12 CSM Configuration

Figure 4 3-12: CSM Settings

CSM Support
Enable/Disable CSM support

GateA20 Active
UPON REQUEST - GA20 can be Disabled using BIOS services.
ALWAYS - do not allow GA20 to be Disabled; this option is useful when any RT
code is executed above 1MB.

Option ROM Messages

Set display mode for Option ROM.

INT19 Trap Response

BIOS reaction on INT19 trapping by Option ROM:
IMMEDIATE - execute the trap right away;
POSTPONED - execute the trap during legacy boot.

Boot option filter

This option controls Legacy/UEFI ROM's priority.

Network
Controls the execution of UEFI and Legacy PXE OpROM.

Storage
Controls the execution of UEFI and Legacy Storage OpROM.

Video
Allows more than two frequency ranges to be supported.

Other PCI devices

Determines OpROM execution policy for devices other than network, storage,
or video.

BIOS SETUP 93
 4.3.13 USB Configuration

Figure 4 3-13: USB Settings

Legacy USB Support

Enables Legacy USB support.
AUTO option Disables Legacy support if no USB devices are connected.
Disable option will keep USB devices available only for EFI applications.

XHCI Hand-off
This is a workaround for OS-es without XHCI hand-off support. The XHCI
ownership change should be claimed by XHCI driver.

USB Mass Storage Driver Support

Enable/Disable USB mass storage driver support.

Port 60/64 Emulation

Enables I/O port 60h/64h emulation support. This should be enabled for the
complete USB keyboard legacy support for non-USB aware OS-es.

USB transfer time-out

The time-out value for control, bulk, and interrupt transfers.

Device reset time-out

USB mass storage device start unit command time-out.

Device power-up delay

Maximum time the device will take before it properly reports itself to the Host
Controller. 'Auto' uses default value, for a root port it is 100 ms, for a hub port
the delay is taken from the hub descriptor.

©Vecow ECS-9000 User Manual BIOS SETUP 94

4.4 Chipset

Figure 4-4: BIOS Chipset Menu

System Agent (SA) Configuration

System Agent (SA) parameters.

PCH-IO Configuration
PCH parameters.

GPIOManager Configuration
GPIOManager parameters.

4.4.1 System Agent (SA) Configuration

Figure 4-4-1: System Agent Settings

VT-d
VT-d capability.

GMM Device (B0:D8:F0)

Enable/Disable SA GMM device.

Above 4GB MMIO BIOS assignment

Enable/Disable above 4GB MemoryMappedIO BIOS assignment. This is
Disabled automatically when aperture size is set to 2048MB.

BIOS SETUP 95
 4.4.2 Graphics Configuration

Figure 4-4-2: Graphics Settings

GTT Size
Select the GTT Size.

Aperture Size
Select the Aperture Size.
Note: Above 4GB MMIO BIOS assignment is automatically enabled when
selecting 2048MB aperture. To use this feature, please Disable CSM Support.

DVMT Pre-Allocated
Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the
Internal Graphics Device.

DVMT Total Gfx Mem

Select DVMT 5.0 Total Graphic Memory size used by the Internal Graphics
Device.

Cd Clock Frequency
Select the highest Cd Clock frequency supported by the platform.

4.4.3 PEG Port Configuration (SA)

Figure 4-4-3: PEG Port Configuration

PEG port options for PCIe device.

©Vecow ECS-9000 User Manual BIOS SETUP 96

4.4.4 Memory Information

Figure 4-4-4: Memory Information

Displays memory information.

4.4.5 PCH-IO Configuration

Figure 4-4-5: PCH-IO Settings

PCH LAN Controller

Enable or Disable onboard NIC.

Wake on LAN
Enable or Disable integrated LAN to wake the system. (The Wake on LAN
cannot be Disabled if ME is on at Sx state.)

Serial IRQ Mode

Configure serial IRQ mode.

State After G3
Specify what state to go to when power is re-applied after a power failure (G3 state).
S0 State: Always turn-on the system when power source plugged-in.
S5 State: Always turn-off the system when power source plugged-in.

BIOS SETUP 97
 4.4.6 PCI Express Configuration

Figure 4-4-6: PCH-IO Settings

DMI Link ASPM Control

Enable/Disable the control of active state power management on SA side of the
DMI link.

Native PCIE Enable

PCI Express Native Support Enable/Disable. This feature is available in vista
and beyond Windows OS.

4.4.7 BIOS Security Configuration of PCH-IO

Figure 4-4-7: BIOS Security Settings

BIOS Lock
Enable/Disable the PCH BIOS Lock Enable (BLE bit) feature.

©Vecow ECS-9000 User Manual BIOS SETUP 98

4.4.8 SB Porting Configuration of PCH-IO

Figure 4-4-8: RAID ROM Settings

SATA RAID ROM

Legacy ROM: Legacy option ROM
UEFI Driver: UEFI Raid Driver
Both: Run the Legacy Option ROM and UEFI driver.

4.4.9 GPIO Manager Configuration

Figure 4-4-9: GPIO Manager Settings

VGA Enable
Enable: VGA display output enabled
Disable: VGA display output Disabled

BIOS SETUP 99
 4.5 Security

Figure 4-5: BIOS Security Menu

Administrator Password
Set administrator password.

User Password
Set user password.

4.5.1 HDD Security Configuration

Figure 4-5-1: HDD Security Settings

Set User Password

Set HDD user password.
*** Advisable to power cycle system after setting hard disk passwords ***
Discard or save changes option in setup does not have any impact on HDD
when password is set or removed. If the 'Set HDD User Password' option is
gray, do power cycle to enable the option again.

©Vecow ECS-9000 User Manual BIOS SETUP 100

4.6 Boot

Figure 4-6: BIOS Boot Menu

Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535 (0xFFFF) means
indefinite waiting.

Bootup NumLock State

Select the keyboard NumLock state.

Quiet Boot
Enables or Disables Quiet Boot option.

Boot Option #x
Sets the system boot order.

New Boot Option Policy

Controls the placement of newly detected UEFI boot options.

Hard Drive BBS Priorities

Set the order of the Legacy devices in this group.

BIOS SETUP 101

 4.7 Save & Exit

Figure 4-7: Bios Save and Exit Menu

Save Changes and Exit

Exit system setup after saving the changes.

Discard Changes and Exit

Exit system setup without saving any changes.

Save Changes and Reset

Reset the system after saving the changes.

Discard Changes and Reset

Reset system setup without saving any changes.

Save Changes
Save changes done so far to any of the setup options.

Discard Changes
Discard changes done so far to any of the setup options.

Default Options:
Restore Defaults
Restore/Load default values for all the setup options.

Save as User Defaults

Save the changes done so far as user defaults.

Restore User Defaults

Restore the user defaults to all the setup options.

©Vecow ECS-9000 User Manual BIOS SETUP 102

A
APPENDIX A : Isolated DIO Guide
A.1 Function Description
The ECS-9000 offers a 16-bit DIO (Isolated/Non-Isolated) 20-pin terminal block
connector, a watchdog timer, and a 4-port PoE.

Isolated DIO pins are fix by Hardware design that cannot change in/out direction
in runtime process. DIO definition is shown below:

Non Non
Pin Isolated DIO Pin Isolated DIO
Isolated DIO Isolated DIO
No. Definition No. Definition
Definition Definition

1 DI0 DIO0 11 DO0 DIO8

2 DI1 DIO1 12 DO1 DIO9

3 DI2 DIO2 13 DO2 DIO10

4 DI3 DIO3 14 DO3 DIO11

5 DI4 DIO4 15 DO4 DIO12

6 DI5 DIO5 16 DO5 DIO13

7 DI6 DIO6 17 DO6 DIO14

8 DI7 DIO7 18 DO7 DIO15

9 DI COM NC 19 DIO GND DIO GND

10 DIO GND DIO GND 20 External VDC NC

Appendix A 103
 Isolated DIO jumper setting is shown below:

JP9

DIO Jumper Setting Status

DIO1 JP9 1-2 NPN (Sink)

2-3 PNP (Source)

PoE definition is shown below:

Port No. Definition Port No. Definition

1 PoE 0 3 PoE 2

2 PoE 1 4 PoE 3

Do NOT use these functions in below:

1. PE-2000: DIO1 (ID = 0), PoE
2. PE-3000: PoE
3. UE-1000: USB (ID = 0)

A.2 Isolated DIO Signal Circuit

DI Reference Circuit:
Sink Mode (NPN) Power DIO Connector
Supply V+ DI_COM (Pin 9)
6-48V DC
V-

DI (Pin1-8)

Source Mode (PNP) Power DIO Connector

Supply V+ DI_COM (Pin 9)
6-48V DC
V-

DI (Pin1-8)

©Vecow ECS-9000 User Manual Appendix A 104

DO Reference Circuit:
Sink Mode Device DIO Connector
(NPN, Default) 6-48V DC
V+ DIO_VDC (Pin 20)

IO DO (Pin11-18)

V- DIO_GND (Pin10,19)

Source Mode Device DIO Connector

(PNP) 6-48V DC
V+ DIO_VDC (Pin 20)

IO DO (Pin11-18)

V- DIO_GND (Pin10,19)

A.3 Software Package Contain

Distribution folder include x32 and x64 versions, use batch
file for installation.
There are included as fallowed:
Win7_32.bat:
Installation for 32-bit driver
Win7_64.bat:
Windows update package which driver required
(need to restart), and Installation for 64-bit driver
Win8_32.bat, Win8_64.bat:
Installation for driver, and guideline to
Framework 3.5 distribution for sample
Win10_32.bat, and Win10_64.bat:
Installation for driver, and
installation to Framework 3.5 distribution for sample
Uninstall_32.bat, and Uninstall_64.bat:
Uninstallation for driver
Run batch file as Administrator.
Support Windows 7 above.
Make sure Windows version before installation.
Runtime folder include head file for software developer or System Integration.
Sample folder include sample program, driver library, and API library.
Source folder include sample program source code that compile on Visual
Studio 2008.

Appendix A 105
 A.4 Sample
Execute DIO demo tool (ECS9K.exe).

Sample ECS9K.exe, as shown below:

DIO1 group:
Isolate check button:
DIO type of DIO configuration, isolated/non-isolated, defined in ECS-9000
series user manual.
Read button:
Set DIO configuration to get DI/DIO input state.
DO type check button:
User setting, DO type of DIO configuration to setup 8 pins - Source/Sink.
Use for Write (DO) button activate.
Write button:
Set DIO configuration to set DO/DIO output state.
DI preference text:
User setting, DI type of DIO configuration by hexadecimal bitmask - Source
/Sink.
Use for Read (DI) button activate.

©Vecow ECS-9000 User Manual Appendix A 106

 DO/DIO output text:
User setting, DO/DIO output state by hexadecimal bitmask - on/off.
Use for Write button activate.
DO/DIO writable text:
User setting, DO/DIO writable of DIO configuration by hexadecimal
bitmask - yes/no.
Use for Read (DIO)/Write button activate.
DI/DIO input text (read only):
DI/DIO input state by hexadecimal bitmask – on/off.
Use for Read button activate.
DO/DIO text (read only):
DO/DIO output state with input state (DIO) and configuration.
Use for Write button activate.
DO/DIO output text (read only):
DO/DIO output state with configuration.
Use for Write button activate.
DI type pin check button (pin 8 ~ pin 1):
User setting, DI pin type of DIO configuration - Source/Sink.
DI/DIO input pin texts (read only, pin 8 ~ pin 1/pin 18 ~ pin 11, pin 8 ~ pin 1):
DI/DIO input pin state
Use for Read button activate.
DO/DIO output pin check button (pin 18 ~ pin 11/pin 18 ~ pin 11, pin 8 ~ pin 1):
User setting, DO/DIO output pin state
Use for Write button activate.
DO/DIO pin writable check button (pin 18 ~ pin 11/pin 18 ~ pin 11, pin 8 ~ pin 1):
User setting, DO/DIO pin writable of DIO configuration.
Use for Read (DIO)/Write button activate.

WDT group:
Write button:
Set WDT when WDT setup text is valid.
Stop button:
Cancel WDT and counting.
Use after Write button action.
WDT setup text:
User setting, WDT value, unit: second.
Use for Write button activate.
WDT counting text (read only):
WDT counting by program timer after set WDT.
Shown after Write button action.
WDT setup day format texts (user setting):
User setting, WDT value, format: day‘hour’minute’second.
WDT counting day format text (read only):
WDT counting, format: day‘hour’minute’second.

Appendix A 107
 PoE group:
Read button:
Set PoE configuration to get PoE state.
Write button:
Set PoE configuration to set PoE state.
PoE output text:
User setting, PoE output state by hexadecimal bitmask - on/off.
Use for Write button activate.
PoE writable text:
User setting, PoE writable of PoE configuration by hexadecimal bitmask -
yes/no.
Use for Write button activate.
PoE mode text:
User setting, PoE mode of PoE configuration by hexadecimal bitmask -
Auto/Manual.
Use for Write button activate.
PoE input text (read only):
PoE input state by hexadecimal bitmask - on/off.
Use for Read button activate.
PoE text (read only):
PoE output state with input state and configuration.
Use for Write button activate.
PoE output text (read only):
PoE output state with configuration.
Use for Write button activate.
PoE input port texts (read only, port 4 ~ port 1):
PoE input port state
Use for Read button activate.
PoE output port check button (port 4 ~ port 1):
User setting, PoE output port state
Use for Write button activate.
PoE port writable check button (port 4 ~ port 1):
User setting, PoE port writable of PoE configuration.
Use for Write button activate.
PoE port mode check button (port 4 ~ port 1):
User setting, PoE port mode of PoE configuration.
Use for Write button activate.

©Vecow ECS-9000 User Manual Appendix A 108

B
APPENDIX B : Software Functions
B.1 Driver API Guide
In Runtime folder, on ECS9K.h:
_DLL_IMPORT_ definition is used on LoadLibrary API for ECS9K.dll.
ECS9K_EXPORTS definition is used on ECS9K.dll building.
Otherwise, that is used to compile with ECS9K.lib.

BOOL Initial(BYTE Isolate_Type, BYTE DIO_NPN)

Initial machine for DIO, watchdog timer, and PoE
Isolate_Type: DIO type
1: Isolated DIO; 0: Non-Isolated DIO
DIO_NPN: DI / DO type
1: PNP (Source) mode for European rule;
0: NPN (Sink) mode for Japanese rule
Return:
TRUE (1): Success;
FALSE (0): Fail (Driver not exists, or initial error (version is too old,
or machine not match))

BOOL GetDIO1Config(BYTE *Isolate_Type, BYTE *DI_NPN,

WORD *Mask)
Get DIO configuration (by variable)
Isolate_Type: DIO type
1: Isolated DIO; 0: Non-Isolated DIO
DI_NPN ([7:0]): DI type, pin setting by hexadecimal bitmask
1: PNP (Source) mode for European rule;
0: NPN (Sink) mode for Japanese rule
DO_NPN: DO type
1: PNP (Source) mode for European rule;
0: NPN (Sink) mode for Japanese rule
Mask ([15:0]): In / Out, pin setting by hexadecimal bitmask
1: Output; 0: Input
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or call by pointer error, or hardware
problem)

Appendix B 109
 BYTE Isolate_Type, BYTE DI_NPN, BYTE DO_NPN, WORD Mask
Set DIO configuration
Isolate_Type: DIO type
1: Isolated DIO; 0: Non-Isolated DIO
DI_NPN ([7:0]): DI type, pin setting by hexadecimal bitmask
1: PNP (Source) mode for European rule;
0: NPN (Sink) mode for Japanese rule
DO_NPN: DO type
1: PNP (Source) mode for European rule;
0: NPN (Sink) mode for Japanese rule
Mask ([15:0]): In / Out, pin setting by hexadecimal bitmask
1: Output; 0: Input
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or hardware problem)

BOOL GetDI1(BYTE *DI)

Get isolated DIO input (DI)
DI ([7:0]): Input state, pin setting by hexadecimal bitmask
1: High; 0: Low
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or call by pointer error, or hardware
problem)

BOOL GetDO1(BYTE *DO)

Get isolated DIO output (DO)
DO ([7:0]): Output state, pin setting by hexadecimal bitmask
1: High; 0: Low
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or call by pointer error, or hardware
problem)

BOOL SetDO1(BYTE DO)

Set isolated DIO output (DO)
DO ([7:0]): Output state, pin setting by hexadecimal bitmask
1: High; 0: Low
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or hardware problem)

BOOL GetDIO1(WORD *DI)

Get non-isolated DIO input (DIO input)
DI ([15:0]): Input state, pin setting by hexadecimal bitmask
1: High; 0: Low
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or call by pointer error, or hardware

©Vecow ECS-9000 User Manual Appendix B 110

 problem)

BOOL SetDIO1(WORD DO)

Set non-isolated DIO output (DIO output)
DO ([15:0]): output state, pin setting by hexadecimal bitmask
1: High; 0: Low
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or hardware problem)

BOOL GetWDT(DWORD *WDT)

Get watchdog timer setup
WDT: watchdog timer setup
Unit: second. (Range: 0 ~ 65535 sec, 1093 ~ 65535 min
(=65580 ~ 3932100 sec))
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or call by pointer error, or hardware
problem)

BOOL SetWDT(DWORD WDT)

Set watchdog timer setup
WDT: watchdog timer setup
Unit: second. (Range: 1 ~ 65535 sec, 1093 ~ 65535 min
(=65580 ~ 3932100 sec))
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or setup 0 error, or hardware problem)

BOOL CancelWDT()
Cancel watchdog timer
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or hardware problem)

BOOL GetPoEConfig(BYTE *Auto, BYTE *Mask)

Get PoE configuration (by variable)
Auto ([3:0]): Auto mode, pin setting by hexadecimal bitmask
1: Auto; 0: Manual
Mask ([3:0]): DC Enable / Disable, pin setting by hexadecimal bitmask
1: Enable; 0: Disable
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or call by pointer error, or hardware
problem)

Appendix B 111
 BOOL SetPoEConfig(BYTE Auto, BYTE Mask)
Set PoE configuration
Auto ([3:0]): Auto mode, pin setting by hexadecimal bitmask
1: Auto; 0: Manual
Mask ([3:0]): DC Enable / Disable, pin setting by hexadecimal bitmask
1: Enable; 0: Disable
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or out of range error, or hardware problem)

BOOL GetPoE(BYTE *PoE)

Get PoE input
PoE ([3:0]): PoE state, pin setting by hexadecimal bitmask
1: On; 0: Off
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or call by pointer error, or hardware
problem)

BOOL SetPoE(BYTE PoE)

Set PoE output
PoE ([3:0]): PoE state, pin setting by hexadecimal bitmask
1: On; 0: Off
Return:
TRUE (1): Success;
FALSE (0): Fail (Initial error, or out of range error, or hardware problem)

©Vecow ECS-9000 User Manual Appendix B 112

C
APPENDIX C : RAID Functions
C.1 SATA Mode for RAID
Please select SATA device to RAID mode on BIOS menu.
Advanced → SATA Configuration → SATA Mode Selection

C.2 OS Installation
ECS-9000 is featured with seven SATA, include two internal SATA, two mSATA,
1 SATA DOM, and 1 CFast.

You can select one of SATA ports for OS installation

We used CFast card for Windows 10 OS installation as an example.

C.3 Install All Device Drivers of ECS-9000 System

The instructions are as follows:
1. Install Chipset driver
2. Install VGA driver
3. Install ME driver (if available)
4. Install Network driver
5. Install Audio driver

Appendix C 113
 C.4 Install “Intel Rapid Storage Technology” Software
You can get the latest information and the software directly from Intel website.

http://www.intel.com/p/en_US/support/highlights/chpsts/imsm

The RAID environment has been done if you completed the steps above.

C.5 Insert SATA HDD for RAID 1

Please notice, you can use seven SATA ports for SATA storage devices.

C.6 Create RAID Volume on “Rapid Storage

Technology” Software
ECS-9000 is featured with seven SATA storage devices for RAID volume, so
there are three options for choose on this page. Let’s take RAID 1 as example,
please select ”RAID 1”.

©Vecow ECS-9000 User Manual Appendix C 114

C.7 Disk Management : Partition the Disk
After RAID 1 volume created, you can see the figure of SATA device allocation.

You will find “Volume_0000” in

SATA device at BIOS menu.

To start Disk Management tool, select "initialize disk."

Then add “Logical Device” for Windows access.

C.8 If One SATA HDD on RAID Volume is Out-of-use

After RAID 1 volume created, you can see the figure of SATA device allocation.

HDD CAUTION Sign

Appendix C 115
 C.9 Recovery and Auto Re-build When Use the SAME
RAID HDD

C.10 Recovery and Auto Re-build When Use DIFFERENT

RAID HDD
There is a warning will pop-up to ask you if the disk is not a member of original
RAID volume.

If you press “Rebuild”, it will replace the broken SATA HDD to the last one SATA
HDD of RAID volume.

©Vecow ECS-9000 User Manual Appendix C 116

D
APPENDIX D : Power Consumption
Testing Board ECS-9000

RAM 16GB x2

USB-1 USB Keyboard Logitech K120

USB-2 USB Mouse Microsoft 1113

USB-3 USB Flash Transcend 3.0 8GB

USB-4 USB Flash Transcend 3.0 8GB

CFAST Transcend CFX600

SATA 0 Transcend SSD370 64GB

SATA 1 TOSHIBA SSD 64GB

LAN 1 (i219) 1.0Gbps

LAN 2 (i210) 1.0Gbps

Graphics Output DVI

Power Plan Balance(Windows7 Power plan)

Power Source Chroma 62006P-100-25

Appendix D 117
 D.1 Intel® Core™ [email protected] (8M Cache, 4.0GHz)
Power on and boot to Win7 (64-bit)
Idle Status :
Standby Mode
Power CPU usage less 3%
CPU
Input Max Max Max Max
Current Consumption Current Consumption
Core™ i7-
06V 0.984A 05.90W 3.166A 19.00W
6700
Core™ i7-
09V 0.650A 05.85W 2.391A 21.52W
6700
Core™ i7-
12V 0.471A 05.65W 1.814A 21.77W
6700
Core™ i7-
24V 0.370A 08.88W 0.945A 22.68W
6700
Core™ i7-
36V 0.322A 11.59W 0.730A 26.28W
6700

Run 100% CPU Run 100% CPU

Power usage without 3D usage with 3D
CPU
Input Max Max Max Max
Current Consumption Current Consumption
Core™ i7-
06V 7.911A 47.47W 10.899A 65.39W
6700
Core™ i7-
09V 5.211A 46.90W 7.114A 64.03W
6700
Core™ i7-
12V 3.984A 47.81W 5.434A 65.21W
6700
Core™ i7-
24V 2.044A 49.06W 2.788A 66.91W
6700
Core™ i7-
36V 1.430A 51.48W 1.931A 69.52W
6700

©Vecow ECS-9000 User Manual Appendix D 118

D.2 Intel® Core™ [email protected] (6M Cache, 4.0GHz)
Power on and boot to Win7 (64-bit)
Idle Status :
Standby Mode
Power CPU usage less 3%
CPU
Input Max Max Max Max
Current Consumption Current Consumption
Core™ i5-
06V 1.057A 06.34W 3.497A 20.98W
6500TE
Core™ i5-
09V 0.693A 06.24W 2.263A 20.37W
6500TE
Core™ i5-
12V 0.495A 05.94W 1.704A 20.45W
6500TE
Core™ i5-
24V 0.371A 08.90W 0.965A 23.16W
6500TE
Core™ i5-
36V 0.332A 11.95W 0.695A 25.02W
6500TE

Run 100% CPU Run 100% CPU

Power usage without 3D usage with 3D
CPU
Input Max Max Max Max
Current Consumption Current Consumption
Core™ i5-
06V 5.457A 32.74W 7.617A 45.70W
6500TE
Core™ i5-
09V 3.482A 31.34W 4.934A 44.41W
6500TE
Core™ i5-
12V 2.622A 31.46W 3.677A 44.12W
6500TE
Core™ i5-
24V 1.421A 34.10W 1.899A 45.58W
6500TE
Core™ i5-
36V 1.004A 36.14W 1.340A 48.24W
6500TE

Appendix D 119
 D.3 Intel® Core™ [email protected] (3M Cache, 3.7GHz)
Power on and boot to Win7 (64-bit)
Idle Status :
Standby Mode
Power CPU usage less 3%
CPU
Input Max Max Max Max
Current Consumption Current Consumption
Core™ i3-
06V 1.196A 07.18W 3.504A 21.02W
6100
Core™ i3-
09V 0.773A 06.96W 2.313A 20.81W
6100
Core™ i3-
12V 0.561A 06.73W 1.728A 20.74W
6100
Core™ i3-
24V 0.405A 09.72W 0.981A 23.54W
6100
Core™ i3-
36V 0.347A 12.49W 0.745A 26.82W
6100

Run 100% CPU Run 100% CPU

Power usage without 3D usage with 3D
CPU
Input Max Max Max Max
Current Consumption Current Consumption
Core™ i3-
06V 6.711A 40.27W 10.041A 60.25W
6100
Core™ i3-
09V 4.405A 39.65W 6.617A 59.55W
6100
Core™ i3-
12V 3.256A 39.07W 4.821A 57.85W
6100
Core™ i3-
24V 1.722A 41.33W 2.593A 62.23W
6100
Core™ i3-
36V 1.253A 45.11W 1.802A 64.87W
6100

©Vecow ECS-9000 User Manual Appendix D 120

E
APPENDIX E : Supported Memory &
Storage List
E.1 Supported Memory List
Testing Board ECS-9000

Memory Test Version: 5.1

Burn-in Test V8.1

E.2 Test Item

Remove
Channel Memory Test Burn-in Flash BIOS
Battery

*2 PASS PASS PASS PASS

*1 (Socket 1) PASS PASS N/A PASS

*1 (Socket 2) PASS PASS N/A PASS

Appendix E 121
 E.3 NON-ECC
Test Temp.
Brand Info NOTE & S/N
(Celsius)

TS9CBSESE0000 25ºC
8G 2Rx8 DDR4
Transcend 8GB C96645-0001 25ºC
2400 SO
C96645-0002 25ºC

4GB Innodisk M0S11601080040001 25ºC

M4S0-4GSSNCRG
DDR4 SODIMM M0S11601080040002 25ºC

8GB Innodisk M0S21606010020001 25ºC

DDR4 2133 W/T M4S0-8GSSO5RG
SODIMM M0S21606010020002 25ºC

16GB Innodisk M0S11608040020001 25ºC

DDR4 2133 W/T M4S0-AGS1O5RG
SODIMM M0S11608040020002 25ºC

Kingston 16GB BKMM1641607 25ºC

2Rx8 2Gx64-Bit KVR21S15D8/16
PC4-2133 BKMM1661618 25ºC

E.4 ECC
Test Temp.
Brand Info NOTE & S/N
(Celsius)

Transcend 16GB 16G 2Rx8 DDR4 C94147-0001 85ºC

ECC Wild Temp. 2133 ECCSO C94147-0002 85ºC

8GB Innodisk M0S11601080090001 25ºC

MSD0-8GSSQCRG
DDR4 2133 ECC M0S11601080090002 25ºC

©Vecow ECS-9000 User Manual Appendix E 122

E.5 Supported Storage Device List
Type Vendor Model Capacity

Intel Intel-310 SSDMAEMC080G2 80GB

mSATA
Silicon Power SP128GMSA301SWO 128GB

Transcend SSD370 TS64GSSD370 64GB

3MG2-P DGS25-64GD81BW1QC 64GB

SATA SSD Innodisk
3MR3-P DRS25-64GD70BCAQC 64GB

MEMXPRO 3MG2-P DGS25-B56D81BW3QC 128GB

SATA HDD TOSHIBA MK5055GSX 500GB

Appendix E 123
 F APPENDIX F : Install Win11
(BIOS TPM Setting)
Step 1 Click on “Advanced”, then click on “PCH-FW Configuration”

Step 2 Click on “PTT Configuration”

©Vecow ECS-9000 User Manual Appendix F 124

Step 3 Click on “dTPM” (TPM Device Selection)

Step 4 Please save the BIOS settings by pressing F4. Please press Enter
when the pop‑up window which asks “Save configuration and exit?”
appears. The computer will then restart.

Appendix F 125
 Step 5 Click on “Trusted Computing”

Step 6 If the window shows “TPM2.0 Device Found Firmware Version:5.62”,

then the setting is completed.

** If more help is needed, please contact Vecow technical support **

©Vecow ECS-9000 User Manual Appendix F 126

For further support information, please visit www.vecow.com

This document is released for reference purpose only.

All product offerings and specifications are subject to change without prior notice.
No part of this publication may be reproduced in any form or by any means, electric, photocopying, or recording,
without prior authorization from the publisher.
The rights of all the brand names, product names, and trademarks belong to their respective owners.
© Vecow Co., Ltd. 2023. All rights reserved.