1

PHY 107/105: BASIC PHYSICS II

Handout I

1.0 ELECTRICITY AND MAGNETISM

1.10 Magnetic Properties of Materials and Their Uses

We begin the discussion of magnetic materials by defining the different terms used. The
laws of electricity and magnetism have a central role in the operation of such devices as
radios, televisions, electric motors, computers, high-energy accelerators, and other
electronic devices. More fundamentally, the inter atomic and intermolecular forces
responsible for the formation of solids and liquids are electric in origin.

1.11 Flux Density in the Magnetic material

The magnetic field intensity B

We define the space around a magnet or a current carrying conductor as the site of a
magnetic field. The magnetic field is represented by the field vector H characterizing the
force due to this field. Its direction at a point is the direction of the force experienced by
a north seeking pole at a point. The other basic magnetic field vector B, is called the

magnetic field induction or the magnetic flux density. It is represented by lines of

induction. The tangent to a line of induction at any point gives the direction of B at that
point.

The lines of induction are drawn so that the number of lines per unit cross-sectional area
is proportional to the magnitude of B. Where the lines are close together B is large and
where they are far apart then B is small.

In order to define B and its units consider a positive charge qo moving with velocity v
through a point and it experiences a force F due to the field. Then we say that the
magnetic field is present at the point, and B is the vector whose magnitude is given by
the relation
F = qovBsin

Where F is in a direction perpendicular to both v and B and  is the angle between v and
B. The units for B from the above relation is thus Newton/(metre/second) which is
referred to as tesla, T. B may also be defined from this relation as the force per unit
current length and at right angles to the magnetic field.
 2

Note: The product qv is a current so any assembly of moving charges or current

will experience a sideways force when in a magnetic field
In general B is proportional to H and the constant of proportionality  (called the
permeability ) depends on the medium of the space where H is present

Thus B = H
In a vacuum  = o and is called the permeability of free space. The ratio of  to o is
called the relative permeability and is thus the ratio of the value of B when there is
material medium to the value when there is only vacuum i. e.

 B
r = =
o Bo
Q: What is the relative permeability of vacuum
What are the units of r
Magnetic flux 
The product of intensity B normal to an area and the cross-sectional area A through
which B passes is called the flux. Flux is thus the number of field lines crossing an area
A and is usually denoted by  and its SI unit is the Weber (Wb). Thus we can write

 =Bacos

where  is the angle between the lines and the area.

Magnetic moment
The orientation of a magnet is specified by means of a vector (called the magnetic
moment) along the axis of the magnet pointing in the direction from the south seeking
end toward the North seeking pole. The orientation of the magnetic moment due to a coil
is specified by the vector  lying along the axis of the coil and pointing in the direction
related to the current by the right hand rule. The magnetic moment of a small plane coil
is a vector whose magnitude is the product of the number of turns,N, the current in each
turn, I, and the area A of the circuit. The direction of the vector is perpendicular to the
plane of the coil in the same sense given by the right hand rule, that is
 = NAI
And is measured in Am2

A magnet in a uniform magnetic field experiences a couple which gives it an angular

acceleration and provided there is damping ultimately comes to rest with its axis parallel
to the field and so the magnetic moment vector and the field vector align. The direction
of the magnetic intensity at a point is the direction into which the magnetic moment
vector of either a small plane coil or a small magnet tends to turn when the small coil or
magnet is placed at that point in space.
 3

1.12: Magnetization
In materials the electrons moving round the nucleus constitute current loops and so the
atoms may have resultant magnetic moments. This may happen in the presence or
absence of a magnetic field. The physical quantity used to describe the magnetic state of
a material is the magnetic moment per unit volume. This is called the magnetization M
i. e.
Total magnetic dipole moment
M =
Volume
Q: What are the units of M

Let us now evaluate the expressions for B and M and their relationship for a point in a
material placed in a magnetic field. Consider a toroid of length L, as shown:

Let the total number of turns = N, mean radius = r, and circumference = L. The total flux
density B depends on the following factors:
(i) the current flowing in the wire
(ii) the magnetization of the material.
Thus we have
B  Bo  Bm
where Bo is the flux density due to the current I in the wire, and Bm is the flux density due
to the magnetization of the material. Usually Bo>> Bm .
Magnetization is related to the average magnet dipole moment for many molecules. The
magnetization flux density Bm is produced by many small circulating currents inside the
magnetic material, due to the circulating and spinning electrons in the atoms. This is
shown in the diagram below:

In the same way, the small circulating currents inside the magnetic materials add up to a
single current Im flowing in the coil wound round the core. This current is called Surface
 4

or Magnetization current, which adds up to the actual current I flowing in the coil. The
actual current produces a flux density Bo.
Let n be the turns per unit length (n = N/L), where L = 2r. Then
 NI N
Bo   o nI  o  o L
2r 2r
Surface current Im produces a flux density Bm, which is given by the equation below

Bm   o nI m

Therefore, the total flux density B is given by

1.13 Intensity of Magnetization B  Bo  Bm
B   n I  I 
The magnetic moment of each current turno due to mthe surface current Im is given as
  A Im
where A is the cross-sectional area of each turn. For the whole toroid, the magnetic moment
is given by

  nLAI m , nL  N
Magnetic moment per unit volume, i.e. intensity of magnetization M, is then

nLAI m nLAI m
M    nI m
V AL
 Bm   o nI m   o M

Similarly, the magnetic field density or magnetic intensity due to the actual(applied) current
I is given by
B = onI

Hence the total flux density B in the material is given by

B  Bo  Bm   o nI   o nI m  o H  o M
  o H  M 
Q: 1. What are the units for H
2. What are the units for  Also find out the value for o

1.14 Relative Permeability and magnetic susceptibility

From the foregoing discussion

B   o H  M 
 H   o  H  M 
And r =  H M M
  1
o H H
 5

The ratio M/H is called the magnetic susceptibility, M, of the material. Hence

r = 1 + M
Thus we see that M is also proportional to H and the constant of proportionality is the
magnetic susceptibility i. e.
M =MH
When a magnetic material, originally unmagnetized, is subjected to an increasing field, the
intensity of magnetization M increases until it reaches a maximum value, as shown below.

Then the material is saturated, i.e. it’s magnetic domains are completely aligned with the
field H. But B can still continue to increase with H.

1.15 Types of Magnetic Materials

Various materials respond differently to changes in the field H. The magnetic materials are
put into three main categories of magnetic behaviour, mainly;
(i) Diamagnetism
(ii) Paramagnetism
(iii) Ferromagnetism

(i) Diamagnets
These are materials whose induced current gives rise to a magnetic field which opposes the
applied magnetic field H. Thus magnetization, M will be in the opposite direction to H and
therefore H/M is negative, and hence susceptibility  is negative. Example is Bismuth with
 = -0.000015.
(ii) Paramagnets
In these materials that atoms are always in thermal motion which causes the magnetic
moments to be oriented purely at random and therefore no resultant magnetization. But if a
field is applied, each atomic moment will try to align in the direction of the field even
though thermal motion will prevent complete alignment. In this case there will be weak
magnetization in the direction of the applied field. Hence susceptibility  of a paramagnet
substance is very small and positive. Example is Platinum with  = +0.0001.
(iii) Ferromagnets
 6

In a ferromagnetic material the magnetization due to orbital electrons is in the same

direction as the applied field. Thus a ferromagnetic material aligns itself with an applied
field. Hence it has high positive susceptibility . Ferromagnetic materials are further
grouped into two:
(a) Soft Magnetic Materials
These magnetise easily and demagnetise when the applied field is removed.
Example is Iron used in transformers.
(b) Hard Magnetic Materials
These are hard to magnetise but retain their magnetism when the applied field is
removed. Example is Steel used in making permanent magnets.

1.16 Hysteresis Loop

The variation of B with applied field H when magnetic material specimen is taken through a
complete circle is as shown below

oa  the field B increases with increase in applied field H.

ab  the applied field H is reduced to zero and the field B follows the path ab.
bc  the applied field H is increased in the opposite direction.
The same process is done with cd and da.
 The point ‘a’ is the saturation point for the material. When the applied field H is reduced
to zero, there is still some magnetic field remaining in the specimen as indicated at b. This
is because the specimen is strongly magnetised, setting up a flux density Br. This flux
density is called the remanance; it is due to the tendency of groups of molecules, or domains
to stay put once they have been aligned. At the point b, the reverse applied H is applied to
the specimen. Each increment of applied field causes a decrease in flux density.
Eventually, the flux density is reduced to zero, when the opposing field H has a value Hc.
Hc is called the coercive force of the specimen. This is a measure of the difficulty of
breaking up the alignment of the domains. We observe that once a specimen is magnetised,
its magnetisation curve never passes through the origin again. Instead it forms a closed loop
called hysteresis loop. Hysteresis is defined as the lagging of the magnetic induction B
behind the applied field H when the specimen is taken through a magnetic cycle.
 7

HomeWork 1

1. (a) Give an account of the domain theory of magnetisation

(b) How does the theory explain the process of magnetization and demagnetization?
2. (a) What is meant by magnetic hysteresis? Sketch a typical hysteresis curve and
explain. What can be deduced from this about the magnetic properties of the material?
(b) What are the desirable magnetic properties for the material of (i) the core of an
electromagnet and (ii) a permanent magnet?
3. A toroid core has N = 1200 turns, length L = 80cm, cross-sectional area A = 60cm2,
current I = 1.5A. Compute B and H. Assume an empty core.
4. A cast iron ring has a mean diameter of 0.2m and an area of cross-section of 5x10-4m2.
It is uniformly wound with 2000 turns carrying a current of 2.0A and the magnetic flux
in the iron is 8x10-3Wb. What is the relative permeability of the iron?
5. The current in the windings on a toroid is 2.0A. There are 400 turns and the mean
circumferential length is 40cm. With the aid of a search coil and charge measuring
instrument, the magnetic field is found to be 1.0T. Calculate
(a) the magnetic intensity
(b) the magnetization
(c) the magnetic susceptibility
(d) the equivalent surface current
(e) the relative permeability