Scribd
Upload
45 views4 pages

Track Link Master Torque

This document outlines the connection procedure for track installation, detailing the required tools and steps involved. It specifies the use of specific tooling and the importance of cleaning surfaces before installation, as well as the torque specifications for bolts. Additionally, it instructs on adjusting track tension after installation.

Uploaded by

Jhein Arundaa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
45 views4 pages

Track Link Master Torque

This document outlines the connection procedure for track installation, detailing the required tools and steps involved. It specifies the use of specific tooling and the importance of cleaning surfaces before installation, as well as the torque specifications for bolts. Additionally, it instructs on adjusting track tension after installation.

Uploaded by

Jhein Arundaa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

2/17/24, 3:59 PM SIS 2.

Track - Connect (M0076745-06)

SMCS - 4170 i09756482

Connection Procedure
PC
Table 1 P- 0
Required Tools 202 005
06: 4 /0 C E
Tool Part Number Part Description

59: 2 /1 7 6
Qty
A 284-5122 Support Stand As
7 2
B 260-9412
M0 48+
Chain As 1
C -
076 09:0
Loctite C-5A Copper Anti-Seize -

©2 745 0
024
Cat
erp
illar
Inc
.

Illustration 1 g01125782

1. Attach Tooling (B) and a suitable lifting device to track (5).

https://sis2.cat.com/#/print-preview /service/87a1b0f4-8455-469e-a509-19603626b85c 1/4


2/17/24, 3:59 PM SIS 2.0

2. Install track (5).

Illustration 2 g01126767

Illustration 3 g01234180

3. Attach Tooling (B) and a suitable lifting device to track shoe (4). The weight of track shoe (4) is
approximately 45 kg (100 lb).
Note: Remove all dirt, rust, and paint from the mating master link surfaces, the threads, and the
master shoe mating surfaces.

https://sis2.cat.com/#/print-preview /service/87a1b0f4-8455-469e-a509-19603626b85c 2/4


2/17/24, 3:59 PM SIS 2.0

4. Connect track master link (2).

5. Apply Tooling (C) to the threads, the body, and the washer face of new bolts (3).

6. Install track shoe (4) and new bolts (3). Tighten bolts (3) to a torque of 750 ± 70 N·m (553 ± 52 lb ft)
in the sequence shown. Turn bolts (3) to an additional angle of 120 ± 5 degrees in the same
sequence.

7. Remove Tooling (B).

Illustration 4 g01125778

8. Raise the blade and remove Tooling (A) from under both sides of the blade.

https://sis2.cat.com/#/print-preview /service/87a1b0f4-8455-469e-a509-19603626b85c 3/4


2/17/24, 3:59 PM SIS 2.0

Illustration 5 g06316061
9. Position the machine to remove the suitable cribbing.

10. Adjust the track tension. Refer to Operation and Maintenance Manual, "Track Tension -
Check/Adjust" for the correct procedure.

PCP-0005CE76
2024/02/17
06:59:16+09:00
i02231598
© 2024 Caterpillar Inc.

https://sis2.cat.com/#/print-preview /service/87a1b0f4-8455-469e-a509-19603626b85c 4/4

You might also like