Technological University

Department of Electromechanical Engineering

Systems Branch
Second Stage Section (B)
Report Name: THERMAL POWER STATIONS

Prepared by
Sahera Jaloud Suleiman
 THERMAL POWER STATIONS

Introduction
 In Steam power plants, the heat of combustion of fossil fuels is utilized by the boilers to
raise steam at high pressure and temperature. The steam so produced is used in driving
the steam turbines or sometimes steam engines couples to generators and thus in
generating electrical energy.
 Steam turbines or steam engines used in steam power plants not only act as prime movers
but also as drives for auxiliary equipment, such as pumps, stokers fans etc.
 Steam power plants may be installed either to generate electrical energy only or generate
electrical energy along with generation of steam for industrial purposes such as in paper
mills, textile mills, sugar mills and refineries, chemical works, plastic manufacture, food
manufacture etc.
 The steam for process purposes is extracted from a certain section of turbine and the
remaining steam is allowed to expand in the turbine. Alternatively the exhaust steam
may be used for process purposes.
 Thermal stations can be private industrial plants and central station.

Major Components of a Thermal Power Plant

• Coal Handling Plant

• Pulverizing Plant
• Draft or Draught fan
• Boiler
• Ash Handling Plant
• Turbine and Generator
• Condenser
• Cooling Tower And Ponds

• Feed Water Heater

• Economiser
• Super heater and Reheater
• Air pre heater
• Alternator with Exciter
• Protection and control equipment
• Instrumentation

BOILER

 A boiler (or steam generator) is a closed vessel in which water, under pressure , is converted
into steam. The heat is transferred to the boiler by all three modes of heat transfer i.e.
conduction ,convection and radiation.
 Major types of boilers are: (i) fire tube boiler and (ii) water tube boiler
 Generally water tube boilers are used for electric power stations.
Fire Tube Boiler
• The boiler is named so because the products of combustion pass through the tubes which are
surrounded by water.
• Depending on whether the tube is vertical or horizontal the fire tube boiler is divided into
two types
1. Vertical tube boiler
2. Horizontal tube boiler
• A fire tube boiler is simple ,compact and rugged in construction. Its initial cost is low.
• Water being more and circulation being poor they cannot meet quickly to changes in steam
demand.
• As water and steam ,both are in the same shell, higher pressure of steam are not possible ,
the maximum pressure which can be had is 17.5 kg/cm2 with a capacity of 15,000kg of steam
per hour.
• For the same output the outer shell of a fire tube boiler is much larger than that of a water
tube boiler.
• In the event of a sudden and major tube failure. Steam explosions may be caused in the
furnace due to rush of high pressure water into the hot combustion chamber which may
generate large quantities of steam in the furnace.
• Fire tube boilers use is therefore limited to low cost small size and low pressure plants.

Figure : Fire Tube Boiler

Water Tube Boilers

• In this boiler, the water flows inside the tubes and hot gases flow outside the tube .
• Water tube boiler are classified as
1. Vertical tube boiler
2. Horizontal tube boiler
3. Inclined tube boiler
• The circulation of water in the boiler is may be natural or forced.
• For Central steam power plants large capacity of water tube boilers are used.
• The tubes are always external to the drum they can be built in smaller size and therefore
withstand high pressure.
• The boiler drum contains both steam and water, the former being trapped from the top of
the drum where the highest concentration of dry steam exists.

Figure :Water tube bolier

SUPERHEATER AND REHEATERS

• The function of the super heater is to remove the last trash of moisture from the saturated
steam leaving the boiler tubes and also increases its temperature above the saturation
temperature.

• For this purpose the heat of the combustion gases from the furnace is utilized.
• Super heated steam is that steam which contains more heat than the saturated steam at the
same pressure. The additional heat provide more energy to the turbine hence power out put
is more.
• Superheated steam causes lesser erosion of the turbine blades and can be transmitted for
longer distance with little heat loss
• A superheater may be convention type, radiant type or combination. However ,convention
•
 superheatersare more commonly used.








Figure : Functions of superheater

Figure: Superheaters

REHEATER
• In addition to super heater modern boiler has reheater also. The function of the reaheater is to
superheat the partly expanded steam from the turbine, this ensure that the steam remain
dry through the last stage of the turbine.
• A reheater may be convention type, radiant type or combination.
Feed Water Heaters: These heaters are used to heat the feed water by means of blend steam
before it is supplied to the boiler. Necessity of heating feed waterbefore feeding it back to the
boiler arises due to the following reasons.

• Feed Water heating improve overall efficiency.

• The dissolved oxygen which would otherwise cause boiler corrosion are removed in the feed
water heater.
• Thermal stresses due to cold water entering the boiler drum are avoided.
• Quantity of steam produced by the boiler is increased.
• Some other impurities carried by steam and condensate, due to corrosion in boiler and
condenser, are precipitated outside the boiler.

Figure: Water steam flow diagram

ECONOMIZER

• Boilers are provided with economizer and air pre-heaters to recover heat from the flue
gases. An increase of about 20% in boiler efficiency is achieved by providing both
economizer and air pre-heaters.

• Economizer alone gives only 10-12% efficiency increase, causes saving in fuel consumption
5-15 %. The feed water from the high pressure heaters enters the economizer and picks
up heat from the flue gases after the low temperature super
heater.

• Economizer can be classified as an inline or staggered arrangement based on the type of

tube arrangement.

• For pressure of 70 Kg/cm2 or more economizer becomes a necessity.

• The tubes are arranged in parallel continuous loops. 

• Feed water flows through the tubes and the flue gases outside the tubes across them. The

feed water should be sufficiently pure not to cause forming of scales and cause internal

corrosion and under boiler pressure. 

• The temperature of the feed water entering the economizer should be high enough so

that moister from the flue gases does not condense on the economizer tubes.

AIR PREHEATERS

• After the flue gases leave economizer, some further heat can be extracted from them and is
used to heat the incoming air for combustion.
• Air preheaters may be of following types:
 Plate type
 Tubular type
 Regenerative type

• Cooling of flue gases by 200increase the efficiency of the plant by 1%.

• The use of air preheaters is more economical with pulverized fuel boilers because the
temperature of flue gases going out is sufficiently large and high air temperatures (250 to
3500 C) is always desirable for better combustion.
• Air preheaters should have high thermal efficiency, reliability of operation, less maintance
charges, should occupy small space, should be reasonable in initial cost and should be
accessible.
• In order to avoid corrosion of the air preheaters, the flue gases should not be cooled below
the dew point.

Figure : Air Preheater

STEAM TURBINES

• Steam entering from a small opening attains a very high velocity.

• The velocity attained during expansion depends on the initial and final content of the steam.
• The difference in initial and final heat content represent the heat energy to be converted to
kinetic energy.
 There are two types of steam turbines:

1)Impluse turbine and

2)Reaction Turbine

Impuse Turbine:

 In this turbine there are alternate rows of moving and fixed blades. The moving blades are
mounted on the shaft and fixed blades are fixed to the casing of the turbine.
 A set of fixed nozzle is provided and steam is passed through these nozzles. The P.E in steam
due to pressure and internal energy is converted to K.E. The steam comes out of the nozzles
with very high velocity and impinges on the rotor blades.
 The direction of steam flow changes without changing its pressure.
 Thus due to the change in momentum the turbine rotor starts rotating.

Reaction Turbine:
 Reaction turbine have no nozzles. These two have alternate rows of moving and fixed
blades. The moving blades are mounted on shaft, while fixed blades are fixed in casing
of turbine.
 When high pressure steam passes through fixed blades, then steam pressure drops
down and velocity of steam increases.
 As steam passes over moving blades, the steam expands and imparts energy,resulting
in reduction in pressure and velocity of steam.
Compounding of steam turbines:

Single stage turbines are of low efficiency.

In compounding, a number of rotors are connected or keyed to the same shaft Two types

of compounding are used: velocity compounding and pressure compounding

Governing of steam turbines:

Governing signifies the process of controlling the volume of steam to meet the load fluctuation.

Figure : Steam Turbines

CONDENSERS

The function of the condenser is to condense the steam exiting the turbine. The condenser helps
maintain low pressure at the exhaust.

Two types of condensers are used.

Table : Jet and Surface Condensers
Jet condenser (contact type) Surface condenser (non-contact type)

Exhaust steam mixes with cooling water. Steam and water do not mix.

Temperature of the condensate and cooling Condensate temperature higher than the
water is same while leaving the condenser. cooling water temperature at outlet.

Condensate cannot be recovered. Condensate recovered is fed back to the boiler.

Heat exchanged by direct conduction Heat transfer through convection.

Low initial cost High initial cost.

High power required for pumping water. Condensate is not wasted so pumping power is
less.

Figure: Surface Condenser

Figure: Surface Condenser

Figure : Jet Condenser

DEAERATORS

 A deaerator is a device that is widely used for the removal of oxygen and other dissolved
gases from the feedwater to steam-generating boilers.

 In particular, dissolved oxygen in boiler feedwaters will cause serious corrosion damage in
steam systems by attaching to the walls of metal piping and other metallic equipment and
forming oxides (rust).
 There are two basic types of deaerators,
1. the tray-type an
2. the spray-type
 The tray-type (also called the cascade-type) includes a vertical domed deaeration section
mounted on top of a horizontal cylindrical vessel which serves as the deaerated boiler
feedwater storage tank.
 The spray-type consists only of a horizontal (or vertical) cylindrical vessel which serves as
both the deaeration section and the boiler feedwater storage tank.
COOLING TOWERS AND SPRAY PONDS
• Condensers need huge quantity of water to condense the steam.
• Water is led into the plants by means of circulating water pumps and after passing
through the condenser is discharged back into the river.
 • If such a source is not available closed cooling water circuit is used where the warm
water coming out of the condenser is cooled and reused.
• In such cases ponds and cooling towers are used where the water loses heat to the
atmosphere.

Figure : Cooling Tower

Figure : Cooling Towers

REFERENCES

1.and Simulation Plant Power Thermal .ed ,D Flynn

2003. ;Press IEE :UK ,Stevenage .Control
2.-Analy Performance Plant Power Thermal .GFM Souza
2012. ;Springer :Heidelberg .sis
3.,ISA ,engineering system control Boiler ,GF Gilman .
2005. ,USA ,Park Triangle Research
4.Engi Plant Power .M Dwivedi ,AP Srivastava ,AK Raja .
;Publishers International Age New :Delhi New .neering
2006.
5.:Instrumentation and Control Plant-Power .D Lindsey
,Stevenage .Systems HRSG and Boilers of Control The
2000. ;Press IEE :UK
6.in control station power of Role .E Ferrari ,G Quazza
Symposium of Proceedings :In .operation system overall
,Baden ,Systems Power Electric of Control Time-Real on
1972. 257,–215 ,Switzerland
7.Society Instrument .controls end front Utility .T Russell
1988. 122,–113 #88-0418, paper ,America of
8.unit a for philosophy control The .E Wulfsohn ,R Landis
boiler a of operation ordinated-co for system control
23.–:19February 1988, Electron .turbine and
9.-Instru .control coordinated of evolution The .HC Gery
112,–109 #88-0417, paper ,America of Society ment
1988