LSE DRIVE

ES600 MODEL
SPACE VECTOR CONTROLLER
LONG SHENQ ELECTRONIC CO., LTD.
 LONG SHENQ ELECTRONIC

About
LONG SHENQ
Long Shenq Electronic co., Ltd., founded in 1985, located in New Teipei City, Taiwan . For many years, we
produce AC motor vector inverters, permanent magnet servo drivers, controller units and peripheral equipment .
We sell these products all over the world with good quality and at reasonable price . In 2002, we passed and we
were recognized by the international quality standard certification ISO9001:2000(new version is 2015), increasing
products quality and customer trust .

The ES600 series is a series of AC drives and servo drives beyond perfection. This series adopts the principle of
voltage space vector control, combined with advanced "direct field conduction" technology to accurately
estimate the magnetic flux, and uses DSP software and hardware for engineering calculations to achieve the
output conversion of the best output excitation torque.

LS1000 apply to precious speed control, for example, AC/DC motor control, servo machine, BLDC, crane
equipment, elevators, vacuum pump and constant pressure water pump control, smart drilling machine etc.
Also, LS1000 can be used in angles and position control, constant speed and torque control . if you have any
required, please contact us .

ES600
1. Built-in SVPWM two-phase modulation.
2. Space vector:
voltage space vector control, automatic current compensation, low output loss and high energy
saving effect.
3. Unique overload capacity: 150%/60 seconds
4. High performance, low noise IGBT module
5. Output frequency 0.1 Hz ~ 480.0Hz, AVR automatic voltage regulator output
6. Serial communication interface RS-485 (baud rate 34800)
7. V/F curve, decreasing curve
8. 8 groups of acceleration and deceleration time options, 8 speeds can be preset
9. The set parameters can be stored/read in pages 1~3
10. Two groups of output Do and Relay can be edited for positive and negative logic functions
ES600 SPECIFICATION

Control Characteristics

Operation method 6 digit number of LED digit display operation. 32- bit DSP-MCU, sine
wave SVPWM control mode, using high-performance low-noise IGBT.
control mode Sine wave SVPWM two-phase modulation, V/F space vector control
Max. output frequency 0.1 ～480.0Hz
Frequency accuracy ： ～
Digital instruction ± 0. 1%(-10℃ +40℃)
(temperature change) ：
Analog instruction ± 0.1%, (25℃ ± 10℃)

Frequency command resolution Digital command:：0.1Hz, Analog command：0.03Hz ( 11bit/60Hz )

Frequency output resolution Digital instruction：± 0.1Hz；Analog instruction：± 0.5 %

Acceleration / deceleration time 0.0 ～ 3000.0( seconds), 8-stage individual & independent setup of
acceleration /deceleration time duration.
V/F curve Automatic torque compensation
5-channel digital manipulator cycle display, decrement curve, digital output
positive and negative logic control, editable digital function terminal,
Control functions parameter memory read and store control, low frequency automatic torque
current compensation, DC brake at start/stop, stall prevention action control,
MODBUSS RS-485 communication, 4 groups of fault history
Signal for frequency setup About 20%, up to 125% with brake controller

Protection functions

Operation method Inverter rated current - heavy duty (HD): 150 % / 1 minute
Motor overload (OL) Electronic overload curve protection (motor rated current)
Instantaneous overcurrent (OC) When over 200% rated current drive trip, motor stops

Automatic restart after Power off for more than 15 ms.

instantaneous power failure

Over Voltage (OL) DC voltage in main circuit ( OU ) : Vdc>410V (220V) / 820V (460V)
Low Voltage (LU) DC voltage in main circuit ( LU ) : Vdc<190V (220V) / 380V(460V)

Over-heat (OH) protected by thermo-switch, include heating sink and charge Resistor.

Stall protection To protect the device from stall during acceleration/deceleration and operation.

Grounding protection Electronic circuit protection.

Environment specifications
Ambient temperature ～
-10℃ +50℃(open type), no freezing
Storage temperature -20℃～+60℃
Humidity Below 95%RH (no condensation condition)
Vibration 20HZ 1G, 20 ~ 50HZ, 0.2G
 Standard type control terminal circuit wiring diagram

Terminal Description
Terminal Designatin
Mark
DI1 Forward command When Di1-COM is connected (ON), it is forward rotation, and when it is

Multi-function Input
open (OFF), it is stopped.
DI2 Reverse instruction When Di2-COM is connected (ON), it is reverse rotation, and when it is
open (OFF), it is stopped.

Terminals
DI3 Input when external abnormality When the external abnormal signal is ON, the inverter will trip and stop.
Abnormal reset
DI4 Inching operation Execute the jog frequency with ON.
DI5 Multi-speed command 1 Multi-stage speed commands 1and 2, with binary 2 bit, can perform
DI6 Multi-speed command 2 four-stage speed control.
COM Input common terminal +24 V output power supply reference ground.
COM Input common terminal +24 V output power supply reference ground.
PNP
OP Digital input common terminal Digital input common terminal.
NPN 24V Power output terminal Power output 24 V/200 mA.
10V Power supply for frequency +10 V/+15 V power supply, current: 30 mA / 50 mA.
frequency setup

setting
AVG Analog signal common terminal The common terminal of analog power, input and output signals.
Analog

AVI Analog voltage frequency DC 0V～10V / 4mA～20mA input。(SW2 pin2 optional setting)。
command
AV2 Analog current frequency DC 0V～10V / 4mA～20mA input。(SW2 pin3 optional setting)。
instructions
DO1 Detected in zero speed It is ON in the stop state or below the zero speed level.
DO2 Detected in Forward It is ON in the Forward state
Multi-function Output

TA1 Contact capacity: AC 250 V/1 A, DC 30 V/1 A

TB1 Output when abnormal *When abnormal, Ta1-Tc1 is ON. *When abnormal,Tb1-Tc1 is OFF.
TC1 When the abnormal protection function of the inverter is activated, it
Terminals

will output with 1a and 1b contacts.

TA2 Contact capacity: AC 250 V/1 A, DC 30 V/1 A
TB2 When in operation *During operation, Ta2-Tc2 is ON. *During operation, Tb2-Tc2 is OFF.
TC2 The inverter output starting frequency is above the set value, and
output with 1a, 1b contact action.
AO Reference output frequency Analog signal output -10 V~10 V.
*With parameter F49 and F56 setting AVG Analog signal common terminal The common terminal of analog power, input and output signals.
*The terminal mark is +10V, when SW2-1 switches ON, the SG+ Serial Communication ：
RS485 serial communication port Positive input.
contact output is 15V, and OFF is 10V Modbus
SG- Serial Communication ：
RS485 serial communication port Negative terminal input
PE Shield isolation ground terminal Covered isolation wire, connection selection ground wire dedicated.

M-type control terminal circuit wiring diagram

(miniaturization)
Terminal Description
Terminal Designatin
Mark
DI1 Forward command When Di1-COM is connected (ON), it is forward rotation, and when it is
Multi-function Input

open (OFF), it is stopped.

DI2 Reverse instruction When Di2-COM is connected (ON), it is reverse rotation, and when it is
open (OFF), it is stopped.
Terminals

DI3 Input when external abnormality When the external abnormal signal is ON, the inverter will trip and stop.
Abnormal reset
DI4 Inching operation Execute the jog frequency with ON.
DI5 Multi-speed command 1 Multi-stage speed commands 1and 2, with binary 2 bit, can perform
DI6 Multi-speed command 2 four-stage speed control.
COM Input common terminal +24 V output power supply reference ground.
COM Input common terminal +24 V output power supply reference ground.
PNP
OP Digital input common terminal Digital input common terminal.
NPN 12V Power output terminal Power output 12 V/200 mA.
10V Power supply for frequency +10 V/+15 V power supply, current: 30 mA / 50 mA.
frequency setup

setting
AVG Analog signal common terminal The common terminal of analog power, input and output signals.
Analog

AVI Analog voltage frequency ～ ～ 。

DC 0V 10V / 4mA 20mA input (SW2 pin2 optional setting)。
command
AV2 Analog current frequency DC 0V～10V / 4mA～20mA input。(SW2 pin3 optional setting)。
instructions
DO1 Detected in zero speed It is ON in the stop state or below the zero speed level.
DO2 Detected in Forward It is ON in the Forward state
Output Terminals
Multi-function

DO3
TA1 Contact capacity: AC 250 V/1 A, DC 30 V/1 A
Output when abnormal *When abnormal, Ta1-Tc1 is OFF.
When the abnormal protection function of the inverter is activated, it
TC1 will output with 1a and 1b contacts.
AO Reference output frequency Analog signal output -10 V~10 V.
AVG Analog signal common terminal The common terminal of analog power, input and output signals.
*With parameter F49 and F56 setting
SG+ Serial Communication ：
RS485 serial communication port Positive input.
*The terminal mark is +10V, when SW2-1 switches ON, the Modbus SG- Serial Communication ：
RS485 serial communication port Negative terminal input
contact output is 15V, and OFF is 10V
ES600 model instructions

E S 6 0 0 X - 2 4 K 0 X X - X X
Version
Drive ES600 series
：：
N No dynamic brake function
D Built-in dynamic brake
： ：
No text Standardization
M Economical type (simplified function)
S：Single phase input
T：Three phase input
2 = 220V Class
4 = 420V Class Input voltage Model specification
4K0=4.0KW
：
ES600 type dimension, Specification
Brake Circuit
Input Voltage KW HP Amps Frame Mode code
Option Built-in

110V 0.4 0.5 3.7 1 ES600M-10K4SN-A1 ○ ×

1Phase input 0.75 1 5 1 ES600M-10K7SN-A1 ○ ×
ES600M economical type

0.4 0.5 3.7 1 ES600M-20K4SN-A1 ○ ×

220V
0.75 1 5 1 ES600M-20K7SN-A1 ○ ×

1Phase input
1.5 2 7.5 1 ES600M-21K5SN-A1 ○ ×
2.2 3 10 1 ES600M-22K2SN-A1 ○ ×
4.0 5 17.5 2 ES600M-24K0SN-A1 ○ ×
0.4 0.5 3.7 1 ES600M-20K4TN-A1 ○ ×

220V 0.75 1 5 1 ES600M-20K7TN-A1 ○ ×

3Phase input 1.5 2 7.5 1 ES600M-21K5TN-A1 ○ ×
2.2 3 10 1 ES600M-22K2TN-A1 ○ ×
4.0 5 17.5 2 ES600M-24K0TD-A1 × ○
0.75 1 3.7 2 ES600M-40K7TN-A1 × ○
380V 1.5 2 5 2 ES600M-41K5TN-A1 × ○
3Phase input 2.2 3 7.5 2 ES600M-42K2TN-A1 × ○
4.0 5 10 2 ES600M-44K0TD-A1 × ○
0.75 1 5 3 ES600-20K7TD-A1 × ○
1.5 2 7.5 3 ES600-21K5TD-A1 × ○
2.2 3 10 3 ES600-22K2TD-A1 × ○
4.0 5 17.5 3,4 ES600-24K0TD-A1 × ○
5.5 7.5 25 4 ES600-25K5TD-A1 × ○
7.5 10 34 5 ES600-27K5TD-A1 × ○
220V 11 15 50 5 ES600-2011TD-A1 × ○
3Phase input 15 20 68 5 ES600-2015TD-A1 × ○
220V 18.5 25 82 6 ES600-2018TN-A1 ○ ×
○
ES600 standard type

3Phase input 22 30 100 6 ES600-2022TN-A1 ×

30 40 130 6 ES600-2030TN-A1 ○ ×
37 50 165 7 ES600-2037TN-A1 ○ ×
45 60 190 7 ES600-2045TN-A1 ○ ×
55 75 230 7 ES600-2075TN-A1 ○ ×
0.75 1 3.7 3 ES600-40K7TD-A1 × ○
1.5 2 5 3 ES600-41K5TD-A1 × ○
2.2 3 7.5 3 ES600-42K2TD-A1 × ○
4.0 5 10 3,4 ES600-44K0TD-A1 × ○
5.5 7.5 15 4 ES600-45K5TD-A1 × ○
7.5 10 17.5 4 ES600-47K5TD-A1 × ○
11 15 25 5 ES600-4011TD-A1 × ○
380V 15 20 38 5 ES600-4015TD-A1 × ○
3Phase input 18.5 25 43 5 ES600-4018TN-A1 ○ ×
22 30 50 6 ES600-4022TN-A1 ○ ×
30 40 68 6 ES600-4030TN-A1 ○ ×
37 50 82 6 ES600-4037TN-A1 ○ ×
45 60 100 7 ES600-4045TN-A1 ○ ×
55 75 130 7 ES600-4075TN-A1 ○ ×
75 100 165 7 ES600-4100TN-A1 ○ ×
 ES600 DIMENSION
UNIT ：m/m

Size 1 2 3 4 5 6 7

Height 145 169 199 286 335 458 563

Width 83 92 115 129 175 253 345

Depth 138 147 151 176 193 227 276

Customized project planning and development services

01 02 03 04 05
Demand Project Development Mass After-sales
Test sample
Planning and Design production service

Confirm customer needs, Development and The products are The products are If the customer makes
product function size, design stage: assembled and mass-produced and necessary modifications
planning and design, Dimension design integrated, and verified verified by customers, to the product, we
and set up a project. Software design by software and and then they can support the following:
Circuit design hardware integration enter the mass Product Hardware
PCB design tests to achieve production stage ModificationsProduct
customer goals. version update

LONG SHENQ ELECTRONIC .CO., LTD.

NO.12-2,WULIN STREET,SHULIN DISTRICT, NEW TAIPEI CITY 23876 , TAIWAN
： ：
Tel +886-2-26842888 Fax +886-2-26842889
LSE DRIVE Email ：[email protected], [email protected]
www.acinverter.com.tw