RICHPEACE

EMBROIDERY CONTROL SYSTEM

Model III - User Manual

 Contents

Operation Instructions for Generation III Embroidery Machine ................................. 1

Chapter 1 Overview ...................................................................错误！未定义书签。

1.1 Safety Warnings and Precautions ...................................................................1

1.2 Main features of embroidery machine ........................................................... 3

1.3 Main Specifications of Machinery .................................................................6

Chapter 2 Embroidery Wizard ..................................................................................... 7

2.1 The structure and operation instructions of the operation box ...................... 7

2.2 Operation Panel Description ..........................................................................7

2.3 Description of the main interface ...................................................................8

2.4 Sudoku module at the right bottom column ...............................................188

2.5 Embroidery function description ................................................................. 25

Chapter 3 Parameter Configuration Wizard .............................................................355

3.1 Parameter configuration of embroidery machine ...................................... 355

3.2 Parameter import and export ........................................................................46

3.3 Parameter setting ..........................................................................................48

3.4 Specifications of headboard parameters .................................................. 4852

3.5 User Notice .............................................................................................. 5555

Chapter 4 Detailed Description of Shortcut Functions ..............................................56

4.1 All zeroing ....................................................................................................56

4.2 Flat embroidery thread hooking ...................................................................58

4.3 Spindle Jogging ............................................................................................59

4.4 Spindle rotation ........................................................................................6060

 4.5 Back to work point ...................................................................................6161

4.6 Back to origin ...........................................................................................6262

4.7 Set offset point ......................................................................................... 6363

4.8 Back offset point ...................................................................................... 6363

4.9 Set embroidery start-point ........................................................................... 65

4.10 Back to embroidery start-point .............................................................. 6666

4.11 Stitching Border checking ..........................................................................67

4.12 Bobbin Thread Trimming .......................................................................... 68

4.13 Flat Emb. Thread trimming ......................................................................688

4.14 Manual color change ..................................................................................69

4.15 Forward and backward ...............................................................................70

4.16 Quantitative frame Moving ........................................................................71

4.17 Needle bar positioning ............................................................................... 71

4.18 Frame Simulating .......................................................................................72

4.19 Manual oiling .............................................................................................73

Chapter 5 Detailed Description of Auxiliary Functions ............................................ 73

5.1 Sensor signals .............................................................................................. 74

5.2 Control actions ...........................................................................................766

5.3 Software Settings ......................................................................................... 78

5.4 Software authorization .................................................................................79

5.5 Network Management ..................................................................................81

5.6 Needle bar setting ........................................................................................ 82

5.7 Common settings ......................................................................................... 84

 5.8 Time setting ..................................................................................................85

5.9 Version Information ..................................................................................... 86

5.10 Production statistics ................................................................................. 877

5.11 Peripheral board version information .................................................... 8888

5.12 Upper thread detection ...........................................................................8888

5.13 Bobbin thread detection ............................................................................. 89

5.14 Spindle Test ................................................................................................90

5.15 Super User ..................................................................................................91

5.16 Main control upgrade .................................................................................92

5.17 Interface Upgrade ...................................................................................... 93

5.18 Error log instructions ................................................................................. 94

Chapter 6 Memory Pattern Management ...................................................................96

6.1 Pattern selection .......................................................................................9696

6.2 Pattern parameters ......................................................................................100

6.3 Color sequence setting ............................................................................... 104

6.4 Pattern import ............................................................................................ 107

6.5 Pattern Export ............................................................................................ 109

6.6 Pattern deletion .......................................................................................... 109

Chapter 7 Pattern Repeat and Transform Setting ................................................... 111

7.1 Repeat mode setting ................................................................................. 113

7.2 Description of Main board control repeat mode .........................................117

Chapter 8 Super User Interface .................................................. 错误！未定义书签。

8.1 HMI Configuration Instruction .................................................................. 122

 8.2 Interface debugging mode description ....................................................... 124

8.3 Description of CSV file .............................................................................. 126

8.4 Reset Install and Debug Progress ...............................................................126

8.5 Explanation of machine parameters ........................................................... 127

8.6 Explanation of working parameters ........................................................... 132

8.7 Flat embroidery headboard parameters ...................................................... 141

8.8 Explanation of Pattern Parameters ............................................................. 146

8.9 Explanation of traversal settings ................................................................ 147

8.10 Explanation of headboard bus detection .................................................. 149

8.11 Description of automatic soft limit setting ............................................... 151

8.12 Explanation of flat embroidery headlock test ...........................................150

8.13 Explanation of flat embroidery hook knife test ........................................153

8.14 Explanation of pattern clearing ................................................................ 154

8.15 Interface decryption ..................................................................................155

8.16 Modify Level 1 Password .........................................................................156

8.17 IoT Configuration .....................................................................................157

8.18 Moving frame angle setting ......................................................................159

8.19 Gear ratio test of main shaft for flat embroidery ......................................160

8.20 Setting the working area for flat embroidery ........................................... 161

8.21 Import and export of moving frame parameters .......................................162

8.22 Delete pattern fcg file ............................................................................... 164

Chapter 9 Wireless PatternTransmission Operation Instructions .............................165

9.1 Operation instructions for wireless Pattern transfer ................................... 165

Chapter 10 Basic steps to start embroidery .............................................................. 169

10.1 Basic flow chart of embroidery ................................................................ 169

10.2 Power on and start up ............................................................................... 169

10.3 Use of the embroidery operating bar ........................................................170

10.4 Instructions for darning operation ............................................................ 170

10.5 How to start embroidery for the first time ................................................171

Chapter 11 Optional Functions of Flat Embroidery ................................................. 172

11.1 Operation instructions for Automatic Bobbin Change ............................. 172

11.2 Operation Instructions for Double-Sequin Device ................................... 179

11.3 Operation Instructions for Multi-Sequin Device ......................................179

11.4 Instructions for handling single loose beads Device ................................ 182

11.5 Operation Instructions of double loose beads Device................................ 185

11.6 Operating Instructions for Simple Chenille Device ................................. 188

11.7 Operation Instructions for Tracing Cording Device...................................191

11.8 Operating Instructions for Laser Cutting Device....................................... 191

Chapter 12 Operation Instructions for Chenille Embroidery ................................... 194

12.1 Parameter setting of chenille .................................................................. 194

12.2 Instructions for the first start-up of chenille embroidery ......................... 197

12.3 Working parameters of chenille embroidery ............................................ 202

12.4 Color-changing board parameters for chenille embroidery ......................202

12.5 Headboard parameters of chenille embroidery ........................................ 207

Chapter 13 Operation Instructions for Coiling Embroidery .....................................206

13.1 Instructions for the first start-up of coiling embroidery ........................... 209
 13.2 Coiling parameter settings ........................................................................213

13.3 Working parameters of coiling embroidery ..............................................215

13.4 Description of coiling headboard parameters ...........................................218

Appendix 1 Error code list ................................................................................. 220217

Chapter 1 Overview
Welcome to use the computerized embroidery machine control system produced by
Tianjin Richpeace AI Co., Ltd. Please read the operation manual carefully before use,
in order to run the computerized embroidery machine correctly.

1.1 Safety Warnings and Precautions

Safety Warnings and Precautions

Do not modify or process the embroidery machine without authorization,

let alone use embroidery machine parts for other machines.

In the process of troubleshooting, must carry out in accordance with the

guidance in the manual, disassembly and maintenance without
instruction are not allowed.

Never put your fingers or other objects into the working area of the
embroidery machine, and machine inside should be cleaned regularly.

Do not use damaged embroidery machine.

No one is allowed to touch the embroidery machine except the operator,

so as not to endanger the personnel safety.

When the embroidery machine is in normal running, neither any

repairing nor maintenance operations are allowed.

Keep the machine away from heat sources, flammable items and
high-density power sources, etc.

After machine working completing, Turn off the power and plug out,
clean the machine, cover it with plastic and place in a designated place.

第 1 页 共 218 页
When the embroidery machine is abnormal, must stop immediately to
troubleshoot.

Before starting the embroidery machine, must check and ensure that the
electrical appliances and magnets are unobstructed and installed in place.

Place the embroidery machine in a moisture-proof, dry and

well-ventilated environment.

Understand the operation instructions of the machine, and pay attention

to the maintenance, before using the machine.

Before stitching operations, it is necessary to check whether the machine

is working properly and well lubricated.

When the embroidery machine is running, keep clean and quiet, make
sure no sharp objects or other sundries around the machine in avoid to
collide with it.

Set the electric voltage and current according to the manual instruction.

When choosing a power socket, make sure its power supply and voltage
are stable and comply with relevant national and local safety standards.

Check the wiring and electrical components regularly when using the
embroidery machine, to avoid damage caused by wiring failures.

The laying of various cables must be reasonably fixed, and the cables
must not be stressed. When the cables pass through sharp surfaces such
as structural holes, they must be handled to avoid damage to the cables.
If necessary, additional insulation such as cable bushing can be added to
improve the insulation function of the cable.

第 2 页 共 218 页
 When using an embroidery machine, the appropriate distribution wire
diameter should be selected according to the working conditions of the
machine, so as to avoid circuit instability caused by too thin or too long
wires, which will affect the embroidery quality and equipment life.

Decide the power supply, voltage and frequency according to the

operating area, to ensure the safety of using the embroidery machine.

1.2 Main features of embroidery machine

1. Humanized touch screen interface
Interface icons and text are concise and clear, so that users can understand at a
glance. Users can define the icons and layout of the interface to make it more
convenient for using. The interface is simple and easy to understand, and the
arrangement of controls is reasonable, allowing users to complete operations quickly.
The interface conform to the principles of ergonomics, adopt appropriate fonts and
color matching, and avoid too dazzling colors or too small fonts. Touch-screen
interface is able to respond to user input timely to avoid stuttering and delays. When
users encounter operational difficulties, they can easily find guidance. Guarantee user
privacy and data security, and prevent attacks and intrusions by bad software.
2. Super large pattern storage
Single pattern can reach 1 million stitches, and the computer storage of total
stitches can reach 1GB, meeting the pattern storage requirements for various users.
3. Normal parameters of each pattern
Pattern parameters and the sequence of color change (needle bar), can record the
work settings of each pattern. When the machine is working on the existing pattern,
the next patterns can be set at the same time, saving time and improving productivity.
More importantly, it is one of the foundations for centralized network management.
4. Group management of embroidery parameters

第 3 页 共 218 页
 The embroidery parameters can be grouped according to the frequently modified
parameters, machine application parameters used by the embroidery technicians and
parameters used by the production factory. The parameters which are used by the
technicians and factory can be saved and restored. And the machine with encryption
function can be encrypted.
5. Input and output patterns by USB port
Users can use the USB disk through USB port to operate the directory, which is
convenient for users to manage patterns.
6. Multiple heads
The number of heads can be customized made to 128, for higher production
efficiency.
7. Multiply patterns input
USB disks support multi-pattern input in the same directory.
8. Network input patterns and color-changing sequence, etc.
The system has network interface, for pattern reading and color-changing sequences
input, etc.
9. Multiply machines networking function
The embroidery monitoring Local Area Network(LAN) can be set up through the
network interface, and connected to the internal network of the embroidery factory, so
as to realize centralized management of the network, improve production efficiency,
and reduce error links in the production process. It is the best choice of embroidery
equipment in the transition from embroidery enterprises to modern enterprise
management.
10. Applique embroidery function
This function can set the pattern changing color code or stop code as the patch
point. When the pattern is embroidered to the patch point, the machine will
automatically stop and move out of the frame. After the cloth is pasted, pulling rod to
continue to embroider.
11. Brake adjustment function

第 4 页 共 218 页
 Users can adjust the braking process parameters according to the different
characteristics of their own embroidery machines to make the main shaft stop
accurately.
12. Stitching Start-port Memory function
This function can memorize embroidery start-point of each pattern, so as to avoid
the tedious work of manual frame-moving to find the start-point every time for the
same pattern.
13. Maintenance and debugging functions of various machines
Including: photoelectric encoder self-inspection, spindle speed self-inspection,
spindle parking at any position, various machine component tests, etc. The application
of this function makes the debugging and fault judgment of the embroidery machine
more convenient.
14. Supports multiple languages
The system supports switching between Chinese, English, Spanish and other
languages.
15. Pattern output
The patterns stored in the computer can be exported and stored to the USB disk.
16. Repeated embroidery function
Set the repeated embroidery for the same pattern to improve production efficiency,
and can be working together with cycle embroidery.
17. Cycle embroidery function
When completing one pattern embroidery, it will return to the origin automatically
to start the next embroidery process. This function cooperates with special pattern
making or repeated embroidery, which can greatly improve the work efficiency.
18. Speed regulation function
The maximum embroidery speed can be set in advance, and the speed will be
automatically adjusted according to the needle distance during the embroidery
process.
19. Thread trimming function

第 5 页 共 218 页
 It can realize the manual control of the thread trimming operation, and automatic
thread trimming during color changing or after embroidery finishes.
20. Thread-breakage detection
If the thread is broken during the embroidery process, or the bobbin thread is used
up, machine will stop automatically with the red light on to give an alarm.
21. Color changing function
Color change can be performed by manual at the color change position, or
according to the preset color change sequence, it will change automatically.
22. Special embroidery function
Including chenille embroidery, coiling embroidery, tape embroidery, zigzag
embroidery, realizes rich and colorful embroidery.

1.3 Main specifications of the machine

The main specifications of the machinery are shown in Table 1-1 as below.
Table 1-1 Main specifications of the machine

1 Memory storage 1GB

2 Single Pattern Stitches 1,000,000 stitches
capacity
3 Screen size and Rated Power 10.1 inches (6W) or 15.6 inches(15W)
4 Touch screen Four-wire resistive
5 Screen resolution(dpi) 1024x600 and 1920x1080
6 Input voltage DC 24 V ±20%
7 Ambient temperature 0°C- 50°C (working); 0°C-60°C ( storage )
8 Humidity 5% -9 0 % ( non-condensing )
9 Number of heads 1～ 128
11 Running speed 100rpm ～ 1500rpm
12 Number of needles 1 to 15

第 6 页 共 218 页
Chapter 2 Embroidery Wizard
2.1 The structure and operation instructions of the operation box
1. Operation box structure
(1) Touch screen
This machine adopts high-brightness LCD display and touch screen human-machine
interface.
(2) USB host interface
This model can be connected with an external USB disk for data input and output.
2. Touch screen operation instructions
As the input device, do not use excessive force or use sharp and hard objects to
click on the touch screen, in order to ensure the service life and performance of the
touch screen.
3. USB disk instructions
Pay special attention to the anti-static issues when using USB disks. Before
inserting or removing the USB disk, please touch the metal frame or machine stand
with your hands to discharge. The USB disk is directional when inserted. Avoid
pulling out the USB disk suddenly when data reading. If the USB is pulled out before
the data is written, or the power is suddenly cut off, the data may be lost. You should
check the integrity of the USB disk data in PC and repair it before continuing to use it.
Note: If power off or USB pulled out suddenly during the process of formatting, it
may cause the USB disk unusable.
4. Network Connection Instructions
Set the machine network parameters before the system is connected to the network,
and then connect, otherwise other machines in the network may not be able to
communicate

2.2 Operation Panel Description

The operation panel is touch screen display as a whole, to control the machine
operation is through the virtual keys on the screen.

第 7 页 共 218 页
2.3 Description of the main interface
The Fig. below is a schematic diagram of the touch screen overall operation main
interface with all functions. Check the display screen if normal or not, or any
appearance damage when getting the machine. If not, then turn on the power, and the
initial screen interface (HMI) will be shown as in Fig. 2-1.

Fig. 2-1 Initial interface

Table 2-1 below shows the names and brief descriptions of the icon functions on the
main interface.

第 8 页 共 218 页
 1 2

3
6

Fig. 2-2 Main interface

8
4

As shown in Fig. 2-2, the main interface of the system is divided into 8 modules for
different functions.
1. System and Software Name at Upper column
2. Pattern working display in the Middle
3. Main Menu at Left column
4. Common Setting at Bottom column
5. Production status at right upper column
6. Speed adjusting at right middle column
7. Basic operation at right bottom column
8. Machine status at Bottom column

第 9 页 共 218 页
2.3.1 Function description of the HMI Upper Column

Fig. 2-3 Upper area display

(1)System Name: Richpeace Embroidery Control System

(2)System version: RSAPL EMB-V230508 (Note: The system version number
depends on the interface version number)
(3)Master control version: DewMock-V230519 (Note: The system version number
depends on the master control version number)

2.3.2 Pattern working display column description in the middle HMI

2
1

3
Fig. 2-4 The main interface display column

There is no any files in the display column when using the machine first time.
Check the pattern from "Pattern Selection" in the "Pattern Setting" menu. And the

第 10 页 共 218 页
pattern parameters setting will pop up after one pattern selected, click "OK", then the
pattern will appear in the display area. The interface is shown in Fig. 2-4 .
There are several columns in display area:
1. Pattern file name
2. Pattern colors sequence,
Click the "Color Sequence Setting" icon to set the color sequence.
3. Pattern stitching information,
Pattern information includes: start-point X coordinate, start-point Y coordinate, W-
width, H-height, C-color sequence number, N-total stitches number;
Click the main interface, it will show the pattern preview. You can click the four

direction keys to move the pattern, icon to center the pattern, icon to zoom

in the pattern and icon to zoom out the pattern. Shown as below:

第 11 页 共 218 页
2.3.3 Main Menu at left

Fig. 2-5 Main Menu

As shown in Fig. 2-5, the main menu at left includes the following information:
1.Pattern setting
2.Parameter setting
3.Embroidery function
4.Shortcut function
5.Auxiliary function
6.Main interface
Their functions are shown in the following table 2-1.
Table 2-1 Functions of main menu icons

Icon Icon Name Description

Pattern Enter "pattern setting" sub-interface, select patterns and set
setting pattern parameters, import and export or delete patterns.
See Chapter 6 for details.
Parameter Enter "Parameter Setting" sub-interface, set embroidery
setting parameters, thread trimming parameters and other

第 12 页 共 218 页
 functions. See Chapter 3 for details.
Embroidery Enter "embroidery function" sub-interface, there are: border
function embroidery, fabric embroidery, applique embroidery,
alternate-head embroidery, positioning line embroidery,
stitch shifting and repeated embroidery. See 2.5 in chapter 2
for the detailed introduction.
Shortcut It is convenient and fast to find the functions from the
function shortcut list. There are: thread hooking, thread trimming,
manual color change, etc. See Chapter 4 for details.
Auxiliary Including bobbin thread and upper thread inspection, super
function user, peripheral board information and main control
upgrading, etc. Auxiliary functions are the interconnection
of the main board and sensors with the display screen. It
plays a key role. See Chapter 5 for details.

2.3.4 Common settings at bottom column

Fig. 2-6 Common setting

第 13 页 共 218 页
As shown in Fig. 2-6, the common functions setting includes the following
information:
1. Pattern selection
2. Set embroidery start-point
3. Back to start-point
4. Border check
5. Back to stitching point
6. Back to origin point
7. Back to offset point
8. Spindle Jog
9. Flat embroidery thread-trimming
10.Manual color change
Note: This column functions are not fixed, set according to operators habits.
Steps to switch the common setting functions as follows:
Open <Main Interface>, click <Assist Function> at left, then find <Common
Settings> in the middle interface, as shown in Fig. 2-7 below.

Fig. 2-7 Switching flow of bottom functions menu

After entering the Common Settings interface, it will display as in Fig. 2-8, then

第 14 页 共 218 页
select the frequently-used functions buttons.

Fig. 2-8 Common settings switching function

After the above steps are completed, click to confirm your selections, and

the menu function buttons at the bottom column will change to the buttons as ordered.

Click to cancel the operation.

Table 2-2 as below shows the names and descriptions of the bottom menu icons
Table 2-2 Bottom menu icon names and descriptions

Display Name Description

Pattern This is the shortcut key for pattern selection on the main
selection interface, for directly entering the pattern selecting
interface, which is more convenient to set the patterns. See
chapter 6 for details.
Set This icon is the button to set the embroidery start-point.
embroidery System will pop up a dialog box to prompt the operator if
start-point setting the current coordinates as the new starting point. If
yes, click , otherwise click .

第 15 页 共 218 页
Back to This icon is the button to return to the embroidery starting
embroidery point. System will pop up a dialog box, and the embroidery
start-point frame will move automatically.
Border This function will check whether the frame is within the
check embroidery range or not. If it is out of range, the frame will
be calibrated automatically.
Back to By this function, machine returns to the position where
stitch-point embroidery stopped, and continues to complete the work of
previous step.
Needle bar The needle bar automatically lifts down to get closer to the
positioning embroidered cloth, in order to make the needle bar stitch at
the set position better. It mainly plays positioning function.
Back to Machine will return to the preset offset-point from the
offset point current position. Offset-point coordinate parameters can be
set according to the x-axis coordinates, y-axis coordinates,
and x/y-axis coordinates.
Spindle jog Click and enter "Spindle jog", it will prompt with one
pop-up "The machine is about to work, please pay attention
to safety!", click " " to execute the operation and the
spindle will rotate to the position of 100 degrees with the
pop-up off. If click " " on the pop-up prompt, the
spindle will not move.
Flat-emb Flat embroidery thread trimming refers to a technique to cut
thread the bobbin thread and upper thread of the flat embroidery
trimming head. The mechanism will automatically complete the
thread trimming through a set of combined actions.
Manual Click manual color change, system will pop up the window
color change

第 16 页 共 218 页
 as , operator can change the

color according to their own requirements, select the needle

position to be changed and click , the needle bar

will change to the selected needle position .

2.3.5 Production status at Upper right column

Fig. 2-8 Upper right Menu

As shown in Fig. 2-8, there are 7 items to show the production status:
1. Working time counting: minutes as the time unit is minutes, it will not be saved
when power off, and it will be counted again after power on.
2. Current needle position: Display the current working needle bar serial number.
Note: When it shows as a negative, it means that the needle bar is not in the correct
position.
3. Main shaft angle: The range of the main shaft angle is 0°~360°. When the icon

shows as a hollow circle " " , it means that the main shaft is not at zero position;

when it shows as a circle with cross " ", it means that the main shaft is at zero
position;

第 17 页 共 218 页
4. Current color sequence: the sequence number of working color.
5. Stitches Qty. index: it shows total number of stitches which has worked.
6. Absolute coordinates: Display the actual coordinate position of current embroidery
frame .
7. Relative coordinates: the coordinate position of current embroidery frame relative
to the embroidery start-point .

2.3.6 Speed Adjusting at right middle column

Fig. 2-9 Speed Adjusting column

Fig. 2-9 is the nixie tube display, indicating current working spindle rotation speed. It

can be adjusted by clicking the higher and lower arrow-icons, for speed

decreasing and for speed increasing, and the digital tube display will change

accordingly.

Note: When the working spindle is unknown (no pattern selected), the rotation speed
is displayed as 0.

2.4 Sudoku module at the right bottom column

Fig. 2-10 The nine-square grid at the bottom right

Fig. 2-10 is Sudoku module for the basic operations tool menu.
1. Forward and backward function: through decreasing or increasing the total
numbers of stitches, to move backward or forward the pattern working position, and

第 18 页 共 218 页
the frame will move to the corresponding position after confirmation.
2. Machine-locking function: to switch machine working state, when it is set to not
allow to work, the machine will not start. Note: This function is used for machine
safety maintenance.
3. Simulating work function: this operation will help to pattern simulating work, but
the spindle does not move, and the others work normally.
4. Interface screen locking function: switch between screen locking and unlocking,
all other keys on the interface cannot be operated if the screen locked.
5. Manual frame-moving function: to control the front, back, left, and right
movement of the embroidery frame)
6. Speed level adjusting function: to adjust the variation of manual frame-moving and
main shaft speed. Manual frame-moving speed can be adjusted to one, two, three
levels by parameters. And the main shaft speed are fixed to three levels: 10r/min,
50r/min, 100r/min. )

2.4.1 Forward and backward

Fig. 2-11 Forward and backward interface

第 19 页 共 218 页
Click the "Forward and Back" icon, middle screen will display the embroidery pattern,

as shown in Fig. 2-11 . Click to , it will return to the first stitch of

pattern; click then , it will move to the last stitch of the pattern; if click

then , the stitches index will be reduced back 100, and the pattern in
the screen will show as 100 stitches backward. The stitches display as in icon

on top will also change. Click and , it returns to the previous

color sequence; click and , it enters the next color sequence. At same

time, the value of displayed color sequence in icon will also change. After
confirmation, the embroidery frame will also move to the corresponding position.

2.4.2 Machine lock function

The default icon is " " with “√” in it, which means the machine is allowed to
work currently. The interface is shown in Fig. 2-1 2 .

Fig. 2-12 Machine-locking function interface

When click the icon button, it switches to " " with “×” in it, and an icon " " will
appear in the status column at bottom, indicating that the machine is not allowed to
work. The interface is shown in Fig. 2-13 .

第 20 页 共 218 页
 When this icon
appears, it indicates
that the machine is
not allowed to work

Fig. 2-13 Machine lock function interface

2.4.3 Simulation work function

The default icon is " " with two hyphens under the two needles, indicating

normal working status, the main shaft and x, y can move, as shown in the interface of
Fig. 2-14.

Fig. 2-14 Simulating work function interface

When click the icon button, it will switch to " " without two hyphens, and icon

第 21 页 共 218 页
" " will appear in the status column at bottom, indicating that the machine is
currently in the simulated working state. In this state, the spindle will not move after
start, and X,Y shafts can move. As shown in Fig. 2-15 .

When machine in
simulation working，
the status will show
this icon.

Fig. 2-15 Simulating work state

2.4.4 Interface Screen-locking function

In default state, the screen is unlocked, as shown with icon " " in Fig. 2-16.

Screen Unlock

Fig. 2-16 Unlocked state

第 22 页 共 218 页
 When click the icon, it will switch to " ", indicating that the screen is currently

locked. As shown in Fig. 2-1 7 interface.

Screen locked

Fig. 2-17 Lock screen status

Under this state, no operation can be performed on the interface, and it will be
forced to change to the main interface. To unlock, Need to click the icon button again
to exit the screen-locking state.

2.4.5 Manual frame-moving function

4 direction buttons

第 23 页 共 218 页
 Fig. 2-18 Manual frame-moving function

There are four direction buttons to adjust the embroidery frame location. As shown
in Fig. 2-18.

2.4.6 Speed Level Adjusting function

Motor speed level

Fig. 2-19 Speed level adjusting interface

The default motor speed level is level two, and the icon is displayed as " ". The
icon button is used to adjust motor speed level of manual frame moving. When click
the icon, it will switch to " " , and the motor speed will change to level three. Click
again, it will change to level one as shown with the icon " ". (Note: The three
speed levels of manual frame-moving can be adjusted by parameters, but the three
levels of main shaft running speed are fixed at 10r/min, 50r/min, and 100r/min.)

2.4.7 Machine status column at HMI bottom

第 24 页 共 218 页
 Fig. 2-20 The bottom status bar display

The bottom status bar is shown in Fig. 2-20 .

Connection status: Indicates whether the machine is properly connected to the

motherboard . There are three values: Not connected, Connecting, Ready.

Not connected: When the machine is not connected to the motherboard , it will
display not connected.

Connecting: When the machine is connecting but not successfully connected, it will
display connecting.

Ready: When the machine is connected to the main board , it will display ready.

Machine status: Current working head, such as chenille, flat embroidery, coiling, etc.

System Time: Displays the current system time.

2.5 Embroidery function description

User Guide: to do embroidery, first click the embroidery function on the main
interface, system enters a sub-interface; and customers can choose the corresponding

第 25 页 共 218 页
functions according to their own requirements.

2.5.1 Border embroidery

When click the border embroidery icon, a dialog as Fig. 2-21 will pop up, click
to operate, and pay attention to the prompts, “machine will move, please operate
carefully”. After the operation done, system calculates the pattern border to generate
temporary data, ready for embroidery, and returns to the main interface with the
auxiliary embroidery icon. Pull the bar to start border embroidery. Border embroidery
is to take the maximum value of the border of the pre-selected pattern to create a
rectangle. After the border embroidery is finished, it will automatically return to the
previous state of preparation for pattern embroidery. If accidentally enter the wrong
interface, click to exit. See Fig. 2-21.

Fig. 2-21 Border embroidery interface

2.5.2 Applique embroidery

The following Fig. 2-2 2 is the applique embroidery setting interface.

第 26 页 共 218 页
 Fig. 2-22 applique interface

There are two kinds of applique embroidery: by color and by stitches number. By
color is to set the distance of the frame corresponding to the color sequence, by
stitches number is to set the distance of the frame corresponding to the stitch. After
setting, embroidery work will stop when it reaches the set color order or the set stitch
order, and frame moves out for manual patching. Following table 2-4 is the parameter
descriptions.
Table 2-4 Parameter icons and descriptions

Parameter icon Description

Displaying pattern colors sequence, and setting the frame
moving distance of each color sequence.
Displaying and setting stitches number index and its moving
distance.
Clear the settings of color sequence and its moving distance,
stitches number index and its moving distance.

2.5.3 Fabric embroidery

Following Fig. 2-23 is the interface for the fabric embroidery with the pop-up at

第 27 页 共 218 页
upper-right.

Fig. 2-23 Matching interface

This function is used to embroider the whole piece of fabric.

Click "Fabric Embroidery" button, and enter the function, as described in following
Table 2-3.
Table 2-3 Fabric Embroidery Mode

Parameter name Description

Needle down Command for needle down. This is to fix the fabric or
adjust the needle bar position, when needle stitches to the
lowest point.
Needle lift Command for needle lifting up.
Exit Exit the fabric embroidery mode and exit this interface.

2.5.4 Positioning Line embroidery

Stitch one line or one curve on the backing fabric, to make a position for the piece
fabric embroidery.

第 28 页 共 218 页
 Fig. 2-24 Positioning Line embroidery interface

Table 2-5 Parameter icons and descriptions

Parameter name Description

Current motor coordinate. Real-time display of frame position.

Manually selected stitching point as the index of current node.

The X coordinate of current node

The Y coordinate of current node

Return to previous node and display its index number. Min. node
index number is 1.
Enter to next node and display its index number. Max. node index
number is 20.
Confirm the current node coordinates.

Delete current nodes index.

Save current operation result.

第 29 页 共 218 页
 Exit position line embroidery function.

2.5.5 Alternate-Head Embroidery

1.Alternate-Head embroidery
It is the embroidery that separates one or several heads between two heads.
First click Super User and enter Interface configuration, then set the three functions to
YES as shown in Fig. 2-25 below.

Fig. 2-25 Interface configuration

Click , and pop-up "Settings will take effect after interface restarts", confirm
with . Wait for the interface to restart, as shown in Fig. 2-26 below.

第 30 页 共 218 页
 Fig. 2-26 Interface restart dialog

Click Pattern Setting, then click Color Sequence Setting and click Alternate-head

embroidery icon , as shown in Fig. 2-27 below.

Fig. 2-27 Color sequence setting interface

第 31 页 共 218 页
Fig. 2-28 (1) Alternate-head embroidery setting interface

Fig. 2-28 (2) Alternate-head embroidery setting interface

第 32 页 共 218 页
 Fig. 2-28 (3) Alternate-head embroidery setting interface

When select mode , the flat embroidery heads will work in odd numbers, and

lights on the working head will also turn green; when select mode, flat
embroidery heads will work in even numbers, and green lights on these heads will be

on. When select mode, all the flat embroidery heads will work, and green light
on all heads. Under the three modes, operator can manually click any head number to
cancel or add to do embroidery work.
2.Double heads combination embroidery
It is based on the combination of two flat embroidery heads. If one head has 9 color
sequences, then the two heads are 18 color sequences. In this way, patterns of more
colors can be done.
Enter color sequence setting interface, click the double-head combined embroidery

icon , and the second head color sequence will pop up. Then set the color

sequence for each needle. As shown in Fig. 2-29 below.

第 33 页 共 218 页
 Fig. 2-29 Double-head Combined Color sequence setting interface

3.Three-head combination embroidery

This is based on the combination of three flat embroidery heads. If one head has 9
color sequences, then three heads have 27 color sequences. So, patterns of more
colors can be embroidered.
Same enter color sequence setting interface, click the three-head combination

embroidery icon , and the second and third heads color sequence will pop up, then

to set the each needle’s color sequence, as shown in Fig. 2-30 below.

第 34 页 共 218 页
 Fig. 2-30 Three-head Combination Emb. Color sequence setting interface

Double-head combined embroidery and three-head combined embroidery are

suitable for large area embroidery or large color quantity embroidery.

Chapter 3 Parameter configuration Wizard

In order to do the embroidery work correctly and achieve the best embroidery effect
as per actual needs, the embroidery machine parameter configuration guidance is very
important for the operators. Therefore, must carefully study and understand how to set
and use the parameters, to ensure high-quality embroidery.

3.1 Parameter configuration of embroidery machine

After getting the embroidery machine, first check whether any main parts or control
panel are damaged. If no damages, then connect power to the whole system, and Pay
attention to the safety of electricity. After power-on, observe whether the control HMI
lights up. If it does not light up, contact the supplier immediately.

第 35 页 共 218 页
 Fig. 3-1 Main interface

Open <main interface>, as shown in Fig. 3-1, find <<Super User>> in <Auxiliary
Function>, super user password 951103. The super user interface is shown in Fig. 3-2.

Fig. 3-2 Super User Interface

Click Interface configuration to set the parameters, as shown in Fig. 3-3, Fig. 3-4,
and Fig. 3-5.

第 36 页 共 218 页
Fig. 3-3 interface configuration

Fig. 3-4 interface configuration

第 37 页 共 218 页
 Fig. 3-5 interface configuration

There are two resolutions, one is 1024*600, and the other is 1920*1080.
Communication method is fixed as network port com., machine type is fixed as 000
embroidery machine, and model is fixed as flat embroidery. The remaining functions
can be config.d as per requirements, such as the intelligent beads embroidery, if have
this function then click YES after the option, or else, click NO. And so on. After
setting up, confirm and Click . And the interface will restart automatically. As
shown in Fig. 3-6.

第 38 页 共 218 页
 Fig. 3-6 Main interface

Fig. 3-7 Super User Interface

Next, set the machine parameters, same to find “Super User” in “Assist function”.
Shown as in Fig. 3-7.

See Fig. 3-8 below for the machine parameter setting interface.

第 39 页 共 218 页
 Fig. 3-8 Machine parameter setting interface

Restore default parameter with its password: 123456. Interface shown as followed

pop-up: “If need to restore to main board default parameter?” Click , the
interface will return automatically.

Clicking then exit the parameter interface. The data becomes the default

parameter value. Shown as below Fig..

第 40 页 共 218 页
 After the parameters are restored to default, enter machine parameters interface to
set flat embroidery heads quantity, needles quantity of each flat head, type of thread
tension-base (Note: Model II thread-tension base have upper and bobbin thread
detection, and Model III thread-tension integrates upper and bobbin thread detection),
and head-locking type. See Fig. 3-9.

Fig. 3-9 Parameter setting interface

第 41 页 共 218 页
 The third step is to set the traversal function. Return to the main interface, same
find “Super User” in the “Assist Function”, See Fig. 3-10.

Fig. 3-10 Main interface

Click to find “Traversal setting” on the second page and set it. As shown in Fig.
3-11.

Fig. 3-11 Super user interface

If the machine parameters are set to 10 heads, there will be 1N, 2N, ... 9N, 10N

第 42 页 共 218 页
signs below, click Nos of traversals, from single traversal to all traversals, click

, all the heads will turn red , Turn up the DIP switch on the machine heads, the

LED light will flash red and green alternately, observe that 1N, 2N, etc. on the screen
change to 1Y, 2Y, etc., then it is successfully done. (Note: When turning on the heads
switch, need to wait for the previous head to flash then proceed to the next head
traversal.) As shown in Fig. 3-13. After the traversal of all machine heads is
completed, all machine heads lights will be off first, and then automatically turn on
sequentially.

Fig. 3-12 Traverse function setting interface

The fourth step is to set the headboard parameters of flat embroidery.

Same, return to the main interface, click Assist function, and find “Super user”. See
Fig. 3-13.

第 43 页 共 218 页
 Fig. 3-13 Main interface

Click to find the headboard parameters of the flat embroidery on the second
page . See Fig. 3-14.

Fig. 3-14 Super User Interface

Three types of head-locking: electromagnet, motor, and none; choose as per

machine configuration. As shown in Fig. 3-15.
Q1 function is connected to the peripheral port, for laser light control and

第 44 页 共 218 页
electromagnet locking, and Q2 function is connected to the peripheral port for laser,
one-way thread-clamping electromagnet, and tracing cording embroidery. Set the
configuration as per order. As shown in Fig. 3-16.

Fig. 3-15 Parameters of flat embroidery machine headboard

Fig. 3-16 Parameters of flat embroidery machine headboard

第 45 页 共 218 页
3.2 Parameter import and export

3.2.1 Import of parameters

Find the “Parameter Import” in the “Auxiliary Function” , and the interface will
show as in Fig. 3-18. Enter the password 290810 .

Fig. 3-17 Parameter import interface

Before importing, insert the USB with parameters in. If no USB inserted, a prompt
"No USB disk detected!" will pop up when click the "Parameter Import" button, as

第 46 页 共 218 页
shown in Fig. 3-17.

Fig. 3-18 Parameter import interface

Insert the USB and click the "Parameter Import", the interface will display the files
of extension format .paradat. Confirm the file and import, as shown in Fig. 3-18.

3.2.2 Export of parameters

Fig. 3-19 Parameter export

Insert the USB before exporting parameters, otherwise prompt "No USB disk

第 47 页 共 218 页
detected!" will pop up, as shown in Fig. 3-19.

Fig. 3-20 Parameter export

After inserting USB, click the "Parameter Export", then a prompt of "Parameter
Export Successful" will pop up. Select the parameter file to be exported, and click
to complete the parameter export. The interface is shown in Fig. 3-20.

3.3 Parameter setting

Back to the Main Interface, find Set Parameters in “Parameter Setting”, as shown in
Fig. 3-21.

第 48 页 共 218 页
Fig. 3-21 (1) Parameter setting

Fig. 3-21 (2) Parameter setting

第 49 页 共 218 页
 Fig. 3-21 (3) Parameter setting

Click "Set Parameter" to the parameters setting interface shown in Fig.s 3-21.
Parameter name Description
Two methods: auto start/manual start.
This is to set the starting mode after color-changing.
Color change start One is to start embroidery automatically without
method stopping after automatic color change, another is to
manually pull the bar to continue working after
automatic color change.
EMB spindle working Spindle motor running speed during flat embroidery
speed
The mending methods have: Manual /Automatic /Full
EMB Mending Method
Full-head / None
Mending Advanced Mending embroidery advanced ending stitches, during
Ending Stitches the range of 0-10.
There are two values: offset point and offset distance.
Applique Offset Method Offset point: move to the set offset point.
Offset distance: distance moving to the offset point.

第 50 页 共 218 页
 The input value range is between (0~999,999,999). 0
Output Preset
presents to turn off the function.
Parking location after The options are: start point /offset point /current
completion position.
Valid Offset point There are: X valid/Y valid/XY valid/invalid.
coordinate
Offset point X X coordinate value range is between
coordinate (-9,999,999.99~9999999.99) mm.
Offset point Y Y coordinate value range is between
coordinate (-9999999.99~9999999.99) mm.
Valid Feeding point There are: X valid/Y valid/XY valid/invalid.
Coordinate
Feeding point X X coordinate value range is between
coordinate (-9999999.99~9999999.99) mm.
Feeding point Y Y coordinate value range is between
coordinate (-9999999.99~9999999.99) mm.
The options are: no oiling / oiling as per working hours /
oiling as per working stitches /continuous oiling.
“Oiling as per working hours” needs to match with
Oiling Method
“oiling stitches interval”.
“Oiling as per working stitches” needs to match with
“oiling hours interval”.
Set a value of stitches interval, when the machine
reaches the value, it will oil automatically.
Oiling Stitches Interval
When choosing the oiling method as per working
stitches, it need to set the stitches interval.
Set a value of hours interval, when the machine reaches
Oiling Hours interval
the value, it will oil automatically.

第 51 页 共 218 页
 When choosing the oiling method as per working hours,
it needs to set the hours interval.
Oiling duration The duration during oiling the machine.
Air duration during The air storage duration during oiling the machine.
oiling Sectional oiling delay (to avoid insufficient pressure).
This is a switch. The default is "off" state. The
Air pressure safety input
parameter "on" is to detect whether the air pressure
Enable
reaches the standard.
It can be detected according to the coordinates to
XY movement limit
prevent moving out of the embroidery position.
After selecting the pattern file, machine will start
Set the start embroidery stitching at the original place when turning on, and take
point automatically the current frame position as the start-point. (this
function can only be enabled when stitches index is 0.)

3.4 Specifications of headboard parameters

1. N5 headboard parameters

Enter “Super User” in “Assist function”, as shown in Fig. 3-22.

第 52 页 共 218 页
 Fig. 3-22 Main interface

Enter password 951103, select flat embroidery headboard parameters, as shown in Fig.
3-22 below.

Fig. 3-22 Super User Interface

Click the icon at the upper right corner. See Fig. 3-23.

第 53 页 共 218 页
 Fig. 3-23 Parameter interface of flat embroidery headboard

Select the corresponding headboard parameters, click to import the

corresponding parameters. As shown in Fig. 3-24 below

Fig. 3-24 Import interface of flat embroidery headboard parameters

After the import done, it will prompt that the parameters have been imported
successfully, as shown in Fig. 3-25 below.

第 54 页 共 218 页
 Fig. 3-23 Parameter Import Popup

3.5 Notice to users

3.5.1 The default parameters before machine shipment

Note: No need to change the default parameters set before machine shipment.
1.Parameter configuration of embroidery machine
For details, see Chapter 3 3.1 Embroidery Machine Parameter configuration
2.Headboard parameter configuration
For details, see Chapter 3 3.4 Embroidery Machine Headboard Parameter
configuration
3. Super user parameter configuration
No need to reconfig. all parameters in the super user, see Chapter 8 for details
4. Machine parameter configuration
Embroidery heads number, needles number in each head, thread trimming mode,
thread tension-base, flat embroidery head locking mode, X zero position sensor, main
shaft parking angle. X-axis homing compensation, Y-axis homing compensation. See
Chapter 8, 8.5 Machine Parameters for details.

3.5.2 Optional Parameters

第 55 页 共 218 页
1. Among the interface configurations in the super user, some functions needs to be
selected according to the actual needs, see the interface configuration description in
Chapter 8 for details.
2. The machine parameters and working parameters in the super user have been
config.d before delivery. For the parameters that users need to set, please refer to
Chapter 8, 8.5 Machine Parameters and Chapter 8, 8.6 Working Parameters.
3. Machine parameter configuration
Flat embroidery head X offset, flat embroidery head Y offset, needs to be selected
according to actual machine configuration.

Chapter 4 Detailed Description of Shortcut Functions

The shortcut functions are some quick operation functions set in the software or
system, which can facilitate users to quickly access commonly used functions or
commands without frequently searching in the interface, improving work efficiency
and user satisfaction.

4.1 All Zeroing

"All zeroing" usually refers to zeroing of X, Y and spindle , and zeroing of motors,
for re-calibrating the motor position.

第 56 页 共 218 页
 Fig. 4-1 All Zeroing

Click the "All to zero" icon, and a pop-up with prompt "Machine is going to move,

please pay attention to safety!"; click to continue and X, Y return to zero,

and click to cancel the operation. As shown in Fig. 4-1.

第 57 页 共 218 页
4.2 Flat embroidery thread hooking

Fig. 4-2 Flat embroidery thread hooking

Click the "EMB hooking" icon, the pop-up with prompt "Machine is going to move,

please pay attention to safety!" is shown in Fig. 4-2. Click to continue, and

the hook knife will be extended and retracted once. Click to cancel the
operation.

第 58 页 共 218 页
4.3 Spindle jogging

Fig. 4-3 Spindle jogging

The operation of main shaft zeroing.

Click the "Spindle Jog" icon, a pop-up with prompt "The machine is going to move,
please pay attention to safety!", as shown in Fig. 4-3. Click " " to perform the
operation, pop-up closed, and then the spindle will rotate to the position of 100
degrees. Click " " button, pop-up closes, and the main shaft keeps still.

第 59 页 共 218 页
4.4 Spindle rotation

Fig. 4-4 Spindle rotation

Click the "Spindle Rotate" icon, a pop-up for setting the spindle rotation angle will
pop up. Set the spindle angle, among range of 0~360 degrees. You can input the
spindle angle, click 0°, 90°, 180°, 270°to control the rotation angle, turn to the
corresponding angle, and confirm with" " to execute the operation . Press and

hold to rotate clockwise, and hold to rotate counterclockwise. When

click " " button, the pop-up closes and the main shaft will not move. The
interface is shown in Fig. 4-4. (Note: When click the rotation button, the speed of the
rotation speed is set in the machine parameters in the auxiliary function)

第 60 页 共 218 页
4.5 Back to work point

Fig. 4-5 Back to work point interface

Click the "Back to Work Point" icon, and a pop-up with prompt "Machine is going
to move, please pay attention to safety!", return to the embroidery stop position,
continue to complete the work of the previous step, and click " " to execute the
operation. Click " " button to cancel the operation, and pop-up closes, main
shaft keeps still. The interface is shown in Fig. 4-5.

第 61 页 共 218 页
4.6 Back to origin

Fig. 4-6 Back to origin interface

It means returning to the machine original position.

Click the "Back to Origin" icon, and a pop-up with prompt "Machine is about to move,
please pay attention to safety!", click " " to execute the operation, and the
machine will return to the preset starting point. Click" " to cancel the operation,
and pop-up closes, main shaft keeps still. The interface is shown in Fig. 4-6.

第 62 页 共 218 页
4.7 Set offset point

Fig. 4-7 Set offset point

The offset point is the position of frame stopping when the applique fabric needs to
put or embroidery work finishes. After setting the offset point, the frame will move to
the preset offset point when the machine receives the offset command, waiting for
next operation. Or the frame moves to the offset point when the embroidery work
done.
Click the "Set Offset Point" icon, the pop-up with prompt "If to set the current point
as the offset point?", click " " to execute the operation, and it will set the current
position as the offset point . Click " " to cancel the operation. The interface is
shown in Fig. 4-7.

4.8 Back to offset point

第 63 页 共 218 页
 Fig. 4-8 Back to Offset interface

It is to let the embroidery frame quickly return to the offset point. This operation
function is valid only after setting the offset point. Click "Back to Offset Point" , a
pop-up with prompt "Machine is about to move, please pay attention to safety!" Click
" " to execute the operation, and the machine will return to the preset offset
point from the current position. Offset point coordinate parameters are related to:
X-axis coordinates, Y-axis coordinates, X/Y-axis coordinates.

第 64 页 共 218 页
4.9 Set the embroidery start-point

Fig. 4-9 Interface of setting start-point

Embroidery start-point has to be set before pattern stitching work. Click icon "Fix
EMB start point", a pop-up with prompt "If to set the current point as the start point?"
Click" " to execute the operation, and set the current position as the start point
of embroidery. Click " " to cancel the operation and pop-up will close. As
shown in Fig. 4-9.

第 65 页 共 218 页
4.10 Back to embroidery start-point

Fig. 4-10 Back to embroidery start-point interface

This is to make the frame return to the EMB start point. Computer has memory
function for EMB start point. Under normal circumstances (for example, the power is
not turned off to push the embroidery frame, etc.), after re-selecting the pattern in the
memory, operate "return to the start-point" will make the embroidery frame move to
the last embroidery start point of the pattern; In abnormal circumstances, please pay
attention whether the limit switch is working properly, to prevent frame collision.
Click "Back to Emb. start-point" icon, a pop-up with prompting "Machine is about
to move, please pay attention to safety!", click " " to execute the operation, and
the machine will return to the preset start emb point from current position. Click "
" to cancel the operation, pop-up closes. As shown in Fig. 4-10.

第 66 页 共 218 页
4.11 Stitching border Checking

Fig. 4-11 Border Check interface

After defining the starting embroidery point, check the stitching border to avoid it
over the frame and damage the machine.
Click "Border Check" icon, a pop-up with prompt "Machine is going to move,
please pay attention to safety!" Click " " to execute the operation. Move left,
right, up, and down to check whether the pattern will exceed the frame range. Click
" " to cancel the operation.
If the pattern does not exceed the range of the embroidery frame, it will
automatically return to the EMB start-point after the check is completed; if it exceeds
the frame range, the computer will automatically find a nearby point as the start-point,
and check the border again. When the pattern embroidery exceeds the range, an error
message will be displayed: X positive limit/X negative limit/Y positive limit/Y
negative limit. As shown in Fig. 4-11.

第 67 页 共 218 页
4.12 Bobbin Thread-trimming

Fig. 4-12 Bobbin-Thread trimming interface

Click "Thread trimming" icon, the pop-up with prompting "The scissors are about
to move, please pay attention to safety!", click " " to execute the operation, and
the scissors open and close once, bobbin thread cut done. Click " " to cancel the
operation, as shown in Fig. 4-13.

4.13 Flat Emb.Thread trimming

第 68 页 共 218 页
 Fig. 4-13 Flat Embroidery Thread trimming interface

Click the "Flat Emb.thread trim" icon, a pop-up with prompt "The machine is about to
cut the thread, please pay attention to safety!", click " " to execute the operation,
main shaft runs and scissors cuts the thread, after trimming done, the hooking knife
works. Click " " to cancel the operation. As shown in the interface shown in Fig.
4-12.

4.14 Manual color change

Fig. 4-14 Manual color change interface

Manual color changing is needed to choose the embroidery needles some times.
Select needle position or color to perform color changing. Click "manual color
change" icon to select the corresponding needle position on the pop-up, clicks " "
to perform the operation , and the embroidery head will change to the corresponding
needle position, for color changing. Click " " to cancel the operation, and the
manual color-changing pop-up will close, as shown in Fig. 4-14 .

第 69 页 共 218 页
4.15 Forward or backward

Fig. 4-15 Forward / backward interface

Click "Forward and Back" icon, the pattern will be displayed on the screen, as shown

in Fig. 2-11 . Click , then , the needle will return to the start position;

click , then , it will move to end stitch position; if click then

, the stitch index will be reduced by100 stitches, and the displayed pattern will

show 100 stitches backward, same time the total stitches will also change.

Click then , the machine returns to the previous color sequence; click

then , machine enters the next color sequence. Same time the color

sequence value will also change. After confirmation, the embroidery frame
will also move to the corresponding position.

第 70 页 共 218 页
4.16 Quantitative Frame Moving

Fig. 4-16 Quantitative frame moving interface

Click the "Quantitative Frame Moving" icon, the pop-up is on, as in Fig. 4-16. The
embroidery frame can be moved in X and Y directions. The moving value range for X
or Y is between (-9,999,999.99~9,999,999.99) mm. Click " " to execute the
operation. Click " " to cancel the operation, pop-up will close.

4.17 Needle bar positioning

第 71 页 共 218 页
 Fig. 4-17 Needle bar positioning interface

Click "needle bar positioning" button, the pop-up with prompt "The needle bar is
going to fall, please pay attention to safety!". Click “ ” to execute the operation,
and the needle bar is lowered . Click " " to cancel the operation, the pop-up
closes. As shown in Fig. 4-17.

4.18 Frame Simulating

Fig. 4-18 Simulate-Frame interface

Click "SimulateFrame" icon, a pop-up with prompt "The machine is going to move,
please pay attention to safety !", as shown in the interface. Click " " to execute
the operation, machine will automatically analyze the current pattern size and draw a
rectangle with the maximum XY direction of the irregular Fig., and move a circle
above the rectangle and stop at the four corners. Click " " to cancel the
operation, pop-up will close.

第 72 页 共 218 页
4.19 Manual Oiling

Fig. 4-20 Manual Oiling interface

Click " Manual oiling " icon, then a pop-up with prompt "The machine is about
to oil ", as shown in the interface in Fig. 4-20. Click “ ” to execute the operation,
and the machine will complete oiling according to oiling time and needles / heads set
in the parameters. Click " " to cancel the operation, pop-up will close.

Chapter 5 Detailed Description of Auxiliary Functions

Auxiliary functions include bobbin-thread inspection and upper-thread inspection,
super user, peripheral board information and main control upgrade, etc. The auxiliary
function, as the interconnection of the main board, sensor and display, plays a key

role. Click the Auxiliary Function icon , the sub-interface will be shown on the

main screen as in the Fig. below. The parameters in the sub-interface can be set and
adjusted. As shown in Fig. 5-1.

第 73 页 共 218 页
 Fig. 5-1 Auxiliary Function interface

5.1 Sensor signal

Fig. 5-2 Sensor signal interface

Click the "Sensor signal" Button, and its interface will appear as shown in Fig. 5-2.
Parameter name Description
Start button Sensor signal for start button, pull the lever to right to
start

第 74 页 共 218 页
Pause button Pull the lever to left to pause the machine
Jog button Press the Jog button, frame moving to Zero
Main frame X zero Main frame X in zero position, generally in the center
position
Main frame Y zero Main frame Y in zero position, generally in the center
position
Main frame X negative Main frame X direction at negative limit
limit
Main frame Y negative Main frame Y direction at negative limit
limit
Main frame X positive Main frame X direction at positive limit
limit
Main frame Y positive Main frame Y direction at positive limit
limit
Air pressure detection 1 To detect the air pressure
Scissors return Scissors return back
Chenille M-axis zero Chenille M-axis in zero position (No display if machine
position no this function.)
Chenille Looping-axis Chenille Looping-axis in zero position (No display if
zero position machine no this function.)
Automatic bobbin Alarm for bobbin changing abnormal
change alarm
Tracing cording alarm Alarm for tracing cording embroidery abnormal
(Note: when press the button, the button grid on the display will light up; after the
sensor receives signal, the sensor grid on the display will also light up.)

第 75 页 共 218 页
5.2 Control Action

Fig. 5-3 Control action interface

Click "Control Action" button, and the interface will be shown as in Fig. 5-3.
Parameter name Description
X moving motor Enable: Enable the driving motor of X-direction moving
Disable: Disable the driving motor of X-direction moving
JogP: X direction moving motor rotates positively
JogN: X direction moving motor rotates negatively
Zeroing: X-direction moving motor returns to zero
Y moving motor Enable: Enable the driving motor of Y-direction moving
Disable: Disable the driving motor of Y-direction moving
JogP: Y direction moving motor rotates positively
JogN: Y direction moving motor rotates negatively
Zeroing: Y-direction moving motor returns to zero
EMB spindle Enable: Enable the EMB spindle
Disable: Disable the EMB spindle

第 76 页 共 218 页
 JogP: EMB spindle rotates positively
JogN: EMB spindle rotates negatively
Zeroing: EMB spindle returns to zero
EMB Color change Enable: Enable flat embroidery color-changing motor
motor Disable: Disable flat embroidery color-changing motor
JogP: EMB color-changing motor rotates positively
JogN: EMB color-changing motor rotates negatively
Zeroing: EMB color-changing motor returns to zero
EMB thread-buckle ON: Turn on the operation of Flat Emb. Thread-buckle
OFF:Turn off the operation of Flat Emb. Thread-buckle
EMB thread-clamp ON: Turn on the operation of emb. upper thread clamping
OFF: Turn off the operation of emb.upper thread clamping
EMB head-locking ON: Turn on flat emb head-locking
OFF: Turn off flat emb head-locking
EMB Oiling ON: Turn on Oiling
EMB hook knife ON: Flat embroidery hook knife stretched
OFF: Flat embroidery hook knife retracted
EMB scissors ON: Flat embroidery scissors stretched
OFF: Flat embroidery scissors retracted
Laser positioning ON: Turn on laser positioning
OFF: Turn off laser positioning
(Note : Turn on EMB head-locking, when the head-locking is electromagnet and
operate ON, the head will not move; when the head-locking is motor and operate ON,
the head will move.)

第 77 页 共 218 页
5.3 Software Settings

Fig. 5-4 Software setting interface

Click the "Software Settings" button, and the interface will be shown as Fig. 5-4
Below is the interpretation for each parameter.
Parameter Description
Different languages are available to suit different requirements,
Language and can be switched at any time as needed.
Language options are: Chinese/English/Spanish/Bengal/Portugal
Font size Normal or Enlarged

Click after setting , and a popup will remind to restart for taking effect,

continue to click to complete the operation. Click to cancel the

operation. As shown in Fig. 5-5.

第 78 页 共 218 页
 Fig. 5-5 Popup Remind interface

5.4 Software authorization

After clicking "Software Authorization" button, pop-up of "Authorization" will be
shown as below, displaying ID, password, time and other information.

Fig. 5-6 Software authorization interface

第 79 页 共 218 页
 Fig. 5-7 Software authorization interface

Click to continue the “authorization”, as shown in Fig. 5-8, and input the

authorization code in the name input box.

Fig. 5-8 Enter authorization password interface

第 80 页 共 218 页
5.5 Network Management
Find and enter “Network Management” in the auxiliary function sub-interface,
and a pop-up for password will appear, as shown in Fig. 5-9. Password: 951103.

Fig. 5-9 Network management password interface

Fig. 5-10 Network management password interface

After enter "Network Management" interface, it will be shown in Fig. 5-10.

第 81 页 共 218 页
 Parameter name Description
MB1 IP setting The default value is 192.168.16.253; ip can be set for main
board 1.
MB1 port settings The default port number is 5000. The input value range of
the port number is between (0~65535).
Local IP settings The default value is 192.168.16.41; the local ip can be set.
Local 1 port setting The default value is 5001, which can be set for the local 1
port, and the input value range is between (0~65535).

5.6 Needle bar setting

Find “Needle bar setting” icon in the auxiliary function and enter the

sub-interface, as shown in Fig. 5-11.

Fig. 5-11 Needle Bar Setting Interface

Click the icon for the number of embroidery needle bar as marked in blue 1, and a
pop-up will appear to set the needle bar number. As shown in Fig. 5-12.

第 82 页 共 218 页
 Fig. 5-12 Needle bar setting interface

The number entered represents needle bars quantity for each head. Select the required
color from the palette at right for the corresponding needle bar. The specific operation
is as follows:
1. Select the embroidery needle bar first, and click the needle bar;
2. Select the required color, click on the color;
3. Then, the selected color will be shown on the embroidery needle bar icon;

第 83 页 共 218 页
5.7 Common settings

Fig. 5-13 Common settings interface

Click and enter "Common Settings" , interface will be shown in Fig. 5-13.
The optional values of these 10 shortcut buttons are: pattern selection /no function/all
zeroing /EMB thread-hooking /spindle jog /spindle rotation /return to working point
/return to origin /offset point setting /return to offset point /Set start- point /return to
start-point /border check /EMB thread trim /bobbin-thread trim /manual color change
/forward and backward /quantitative frame moving /hardcore positioning /simulating
frame /process reset /back to loading point.
Setting "Shortcut Buttons" can change the icons and functions of the menu buttons at
the bottom of the main interface.

第 84 页 共 218 页
5.8 Time setting

Fig. 5-14 Time setting interface

Click and enter "Time Setting", the interface will be shown as Fig. 5-14.

Fig. 5-15 Time setting interface

After setting, click to confirm; and follow the pop-up reminder to restart the

machine to make the time setting effect. As shown in Fig. 5-15.

第 85 页 共 218 页
 Parameter name Description
Year The input value range is between (1000~9999)
Month The input value range is between (1~12)
Day The input value range is between (1~31)
Hour The input value range is between (0~23)
Minute The input value range is between (0~59)
Second The input value range is between (0~59)

5.9 Version Information

Fig. 5-16 Version information interface

Click "Version Information" button to the system info interface, shown as in Fig. 5-16.
This version information includes N1 board main control software version, MB
hardware version, and MB N1 software version. (Note: The first two digits of the
main board version and N1 board version must be same. If they are not the same,
please contact the relevant personnel firstly.)

第 86 页 共 218 页
5.10 Production Statistics

Fig. 5-17 Production statistics interface

Click and enter "Production Statistics" interface, shown as Fig. 5-17.

Parameter name Description
Total Patterns Total patterns processed from machine starting to the present
processed
Total emb. stitches Total stitches embroidered from machine starting to the present
Pattern name Name of current working pattern
Thread-breakages Total times of thread-breakages from machine start to the
present
Clear “Total patterns processed”, “Total emb. Stitches” and
“Thread-breakages”;
Delete
When click "Delete" button, a pop-up with prompt "Do you
want to clear the production statistics?" will remind you.

第 87 页 共 218 页
5.11 Peripheral board version information

Fig. 5-18 Peripheral board version information interface

Click and enter "Peripheral Board Information" interface shown as in Fig. 5-18. there
will display the program information of N5, N6, D86 and other peripheral boards
(N5C board for chenille embroidery, N5E board for coiling embroidery).

5.12 Upper thread detection

Click and enter "Upper thread detection" interface, as shown in Fig. 5-19:

第 88 页 共 218 页
 Fig. 5-19 Upper thread detection interface

Click the button to start detection. When the thread take-up spring touches

the needle bar case, the head light will flash in red. When the thread take-up spring

leaves the head, and the head light is in green, then press the button to pause

the detection. (Note: model III thread tension base integrates upper thread and bobbin
thread. )

5.13 Bobbin thread detection

Fig. 5-20 Bobbin thread detection interface

Click and enter "Bobbin thread detection" interface, shown as in Fig. 5-20. Select a

needle firstly, then click the button to start detection, the head light will flash

in red, turn the bobbin thread wheel, and the light will always be green, then click

button to pause the detection.

第 89 页 共 218 页
5.14 Spindle Test

Fig. 5-21 Spindle test interface

Click and enter "spindle test" , as shown in Fig. 5-21.

Set EMB spindle turns and EMB spindle speed. Fig. 5-22 is pop-up of EMB spindle
turns, set the turns of spindle rotating for test; and Fig. 5-23 is pop-up of EMB spindle
speed for test (testing speed is not suitable to set too high, 100r/min - 400r/min).

Fig. 5-22 EMB spindle turns

第 90 页 共 218 页
The two parameters description shown in the table below.
Parameter name Description
EMB spindle turns Flat embroidery spindle rotating turns;
The input value range is between (1~999,999,999).
EMB spindle speed Flat embroidery spindle rotating speed;
The input value range is between (1~3000) r/min.

5.15 Super User

Fig. 5-24 Super user interface

Some commands that are not commonly used or only for administrators can be
operated by entering passwords, the super user function is for manufacturer technical
person. Superuser password is 262574. And 951103 is the highest authority password.
Click "Super User" button, and a pop-up of "Password Input" will appear as
shown in Fig. 5-24.

第 91 页 共 218 页
5.16 Main control upgrade

Fig. 5-26 Main control upgrade operation interface

Find and click “MC Upgrade” in Auxiliary Function, as shown in Fig. 5-26 above.

Fig. 5-27 Upgrade password input interface

Input the password as shown in Fig. 5-27, then click .

Select the program that needs to be upgraded, and click , then machine will

第 92 页 共 218 页
automatically upgrade. During the upgrading process, don’t turn off the machine
neither operate. After upgrade completed, machine will automatically restart.
The main control upgrade file supports .rnpu files.

Fig. 5-28 Upgrade waiting interface

Waiting for the main control upgrade complete, as shown in Fig. 5-28.

5.17 Interface upgrade

Fig. 5-29 Interface upgrade interface

第 93 页 共 218 页
Insert USB before importing parameters.If no USB disk inserted, when click “HMI
Update”, there will be pop-up with a prompt "No USB disk detected!".

Fig. 5-30 Interface after importing parameters

Insert USB disk, click "HMI Upgrade " button and select the parameter file to be
upgraded, as shown in Fig. 5-30. Files with the .rcc suffix are pictures, files with
the .qm suffix are language packs, and files with the .XPlatForm suffix are
applications. The .aut suffix file is the above overall package file.

5.18 Error log description

Click and enter ErrorLog interface, you will see the date and time and error content,
as shown in Fig. 5-31 below.

第 94 页 共 218 页
 Fig. 5-31 Error log interface

Click export icon at the upper right, pop-up with prompt “ Do you want to

export journal?” Click to continue. Click to cancel the operation. As

shown in Fig. 5-32 below.

Fig. 5-32 Log file export interface

Icon is thread-breakage statistics, click export button, the file exported will be

CSV file in an excel form, and the current language will be the exported language.

第 95 页 共 218 页
Chapter 6 Memory Pattern Management
Memory pattern management refers to the function of storing various patterns and
pattern data in the memory and being able to manage, retrieve and use these data in
the embroidery machine. Usually, the pattern data is generated by a computer or input
into the embroidery machine from other sources, imported into the system through a
USB disk, and stored in the memory of the embroidery machine.

6.1 Pattern selection

Find and enter "Pattern Setting" from "Main Interface", then find "Pattern
Selection". There in the interface will display all the existing patterns of the machine.
Click the required pattern file, and the relevant information of the pattern will be
displayed on the right. Followings are the operation steps.

1. Click “Pattern Selection” icon " " in “Pattern Setting” interface shown in Fig.
6-1.

Fig. 6-1 Pattern setting interface

第 96 页 共 218 页
pattern

Fig. 6-2 Pattern selection file interface

2. After enter “Pattern Selection” interface, there will be all the patterns displaying.
Click page up “ ” or page down “ ”to browse the pattern. Directly click
the pattern, and all the relevant information and parameter settings of the pattern will
be displayed on the preview image at right, as shown in Fig. 6-2, parameters meaning
will be interpreted in Table 6-1. Click " " to enter the interface shown in Fig.
6-3:

Pattern information

Pattern parameter

Fig. 6-3 Pattern parameter information

第 97 页 共 218 页
 Table 6-1 Parameter names and descriptions

Parameter name Description

Pattern name HTEST~1.DST is the name of the pattern
N The total number of stitches of the pattern
C The color sequence number of the pattern
W The width of the pattern
H The height of the pattern
X X-direction range
Y X-direction range
Zoom ratio(x,y) Setting of pattern scaling ratio
Rotation angle Setting the rotation angle of the pattern
Pattern direction Set the pattern direction reversal style for the pattern
Priority Setting the priority mode for patterns during repeated
embroidery
Repeated way Repeat pattern setting
Nos of repetitions (x,y) Set the number of repetitions of the pattern (x, y)
Repeat interval(x,y) Set the repetition interval for the (x, y) of the pattern

第 98 页 共 218 页
 Fig. 6-4 Parameter Modify Interface

3. The interface lists some default values of the currently selected pattern, and you
can also click the item to be modified, and a dialog box will pop up to modify the
parameter value (see the second part of Section 6.2 for the parameter meaning), as
shown in the interface in Fig. 6-4.

第 99 页 共 218 页
 Fig. 6-5 Lock stitches times interface

4. After modification, click " "to save the pattern information in the memory;
after saving, click the confirmation icon " ", it will return to the main interface.

6.2 Pattern parameters

Fig. 6-6 (1) Pattern parameters interface

第 100 页 共 218 页
 Fig. 6-6 (2) Pattern parameters interface

Fig. 6-6 (3) Pattern parameters interface

Parameter name Description

Times of lock stitches before embroidery starts. The range of
Lock stitch times
input value is between (0~10).
Lock stitch steps Number of stitches for locking stitches before embroidery

第 101 页 共 218 页
 starts. The range of input value is between (0~10).
The length of the interval between two stitches when locking
Lock stitch length
stitches. The input value range is between (0.00~1.00) mm.
There are 8 commonly used rotation styles for the pattern flip.
Flip style (for details, see the section 4.1 transformation mode setting in
chapter 4)
Use the rotation angle to modify when the common flip styles
cannot be satisfied. The input range of numbers is 0~90
Rotation angle
degrees. After modification, the effect is that the pattern rotates
clockwise by an angle, and input value is 0~9.
Zoom in or out to the pattern at X direction. Input value from
the number key, which is between 50 and 200. Inputting 100
X- magnification
means same size as the original, 50 means half of the original
size ( 50% ), and 200 means double the size ( 200% ).
Zoom in or out to the pattern at Y direction. Input value from
the number key, which is between 50 and 200. Inputting 100
Y- magnification
means same size as the original, 50 means half of the original
size ( 50% ), and 200 means double the size ( 200% ).
Set horizontal priority or vertical priority in repeated
embroidery. Optional values are: Horizontal embroider
first/vertical embroider first.
1.Horizontal-embroidery first: doing embroidery horizontally
Order of priority (x-direction) firstly during repeat-embroidering, and continue to
embroider other rows one after another (x-direction).
2.Vertical-embroidery first: doing Embroidery vertically
(y-direction) first during repeated embroidery, and continue to
embroider other columns one after another (y-direction).
X-repetition times Set how many patterns to embroider repeatedly in the x

第 102 页 共 218 页
 direction, that is, nos of patterns produced by embroidery, and
the setting value is between 1 and 200.

Set how many patterns to embroider repeatedly in the y

Y-repetition times direction, that is, nos of patterns produced by embroidery, and
the setting value is between 1 and 200.
The distance between the x-direction edges of two patterns.
X-repeat spacing
The input value is between (-3000.0~3000.0)mm.
The spacing between the two patterns edges in the y direction.
Y-repeat spacing
The input value is between (-3000.0~3000.0) mm.
X-direction compensation is a small displacement adjustment in
the horizontal direction to make the embroidery thicker or
X -compensation thinner in the x-direction to meet customer needs. The input
value is between (-3000.0~3000.0) mm. The unit is 0.1mm, that
is, 200 means 20mm.
Y-direction compensation is a small displacement adjustment in
the vertical direction to make the embroidery thicker or thinner
Y- compensation in the y-direction to meet customer needs. The input value is
between (-3000.0~3000.0) mm. The unit is 0.1mm, that is, 200
means 20mm.
The inserted jump stitch size is each step distance along the
processing path , and the input value is between
Jump-stitch size
(7.00~100.00)mm. When the stitch size is larger than the set
inserted
value, the stitch distance will be divided into two stitches, and
the first stitch is the jump stitch.
"X-axis Offset allowance" refers to the allowable offset degree
X-axis Offset of the workpiece in the x-axis direction during processing or
Allowance production. The X offset point can only be set after state is
"On". The priority is higher than the general offset point. And

第 103 页 共 218 页
 the previous offset point will be invalid once this offset point
set.

"Y-axis Offset allowance" refers to the allowable offset degree

of the workpiece in the y-axis direction during processing or
Y-axis Offset production. The Y offset point can only be set after state is
Allowance "On". The priority is higher than the general offset point. And
the previous offset point will be invalid once this offset point
set.
The x coordinate of the offset point. The input value range is
X Offset point
between (-9999999.99~9999999.99) mm.
The y coordinate of the offset point. The input value range is
Y Offset point
between (-9999999.99~9999999.99) mm.
Offset point x The x coordinate of the offset point. The input value range is
coordinate between (-9999999.99~9999999.99) mm.
Offset point y The y coordinate of the offset point. The input value range is
coordinate between (-9999999.99~9999999.99) mm.
Click and enter "Pattern Parameters" interface shown as Fig.s 6-6:

6.3 Color sequence setting

Color sequence setting, is to set the color sequence of the current pattern according
to the provided embroidery needle bar.

第 104 页 共 218 页
 Show

Colors needs to be
set in the pattern

Fig. 6-7 Pattern color sequence interface

Click and enter "Pattern Color Sequence" interface as shown in Fig. 6-7. The color
sequence of the pattern can be set in the yellow box area on the left. The Fig. shows
that there are 3 color sequences in this pattern. The operation of setting the color
sequence is as follows:
1. Click the color sequence icon that needs to be set in this pattern.
2. Then click the icon from the embroidery needle bar, which is the position indicated
by the mark 2.
3. At this time, the corresponding color sequence icon of the pattern is displayed
same color in embroidery needle bar 1, as shown in Fig. 6-8.

第 105 页 共 218 页
 Fig. 6-8 Set color sequence interface

The preview image at right dynamically displays which embroidery needle bar is
used in which position of the design according to the selected color sequence. In
addition, it also displays pattern name, total stitches, total colors, beginning stitches of
the current color sequence, end stitches of the current color sequence, needle bar
selection and other information.
Parameter Description
name
Color sequence cycling: in a 6-needle position, if you want to set the
color of the last three needle positions to be the same as the first

three, firstly set the first three needle positions color and click ,

then the last three are exactly the same as the first three color
sequences, which avoids complicated operation due to multiple color
sequences.
Clear the current color sequence settings and restore the default color
sequence settings. If there is a pattern color sequence table, then
restore to the default value. If there is no pattern color sequence table,
then clear it, and regenerate the preview image.

第 106 页 共 218 页
6.4 Pattern import
Insert a USB disk, the interface will display the files and folders in the USB, select
the pattern file you need to import, and the preview image of the pattern and related
information of the pattern will be displayed at right.

Fig. 6-9 Pattern import interface (without USB disk)

If no USB disk inserted, click "Pattern Import" icon, the interface will be shown as
Fig. 6-9.

第 107 页 共 218 页
 Fig. 6-10 Pattern import interface (with USB disk)

After inserting the USB disk and clicking "Pattern Import" button, the interface will
be shown in Fig. 6-10. Select the pattern file you want to import, and pattern preview
will be shown at right, as in Fig. 6-11.

Show

Choose pattern

Fig. 6-11 Pattern import preview interface

Parameter name Description

Pattern name The name of the imported pattern
X X coordinate

第 108 页 共 218 页
Y Y coordinate
W Pattern width
H Pattern height
C Number of color sequences
N Total stitches
Select all files with the suffix dst/dsr
Back to the previous directory
If importing the patterns with same name, system interface will prompt to replace
or rename.

6.5 Pattern export

Fig. 6-12 Pattern export interface

Click and enter "Pattern Export" interface, as shown in Fig. 6-12. All existing
patterns in the machine will display, and select the required pattern file to export
(multiple pattern files can be selected for export, and the preview at right only shows
the last selected pattern).

第 109 页 共 218 页
 Show

Choose pattern output

Fig. 6-13 Pattern export preview interface

After selecting the pattern file to be exported, the preview image will show the
pattern effect and pattern information at right. You can also select multiple patterns to
export. By default, it will display the last pattern image and related information, as
shown in Fig. 6-13.

6.6 Pattern deletion

Fig. 6-14 Pattern delete interface

Click and enter “Pattern Deletion” interface, it will display all the existing pattern

第 110 页 共 218 页
files of the machine, just select the file you want to delete. As shown in Fig. 6-14.

Fig. 6-15 Pattern delete interface

Select the pattern file you want to delete, or multiple pattern files, and the pattern
and information of the last selected file (encryption test 01.dsr) will be displayed on
the right, as shown in Fig.-15. Click OK to execute the operation of deleting the
pattern.

Chapter 7 Pattern Repeat and Transform Setting

“Repeat & Transform” refers to the setting of repeating mode and transforming
mode for patterns.

1. Click and enter “Pattern Setting” interface, shown as in Fig. 7-1.

第 111 页 共 218 页
 Pattern

parameter

Fig. 7-1 Pattern setting interface

2. Click and enter “Pattern Parameter icon” interface, as shown in Fig. 7-2. The

yellow block area is to set the parameters for embroidery pattern.

Fig. 7-2 (1) Pattern parameter setting interface

第 112 页 共 218 页
 Fig. 7-2 (2) Pattern parameter setting interface

7.1 Repeat mode setting

Fig. 7-3 (1) Pattern repeat mode setting interface

第 113 页 共 218 页
 Fig. 7-3 (2) Pattern repeat mode setting interface

There are 6 parameters related to the repeating mode setting in the red block area :
1. Repeat mode: including 4 options, usual repeat, X-axis symmetry, Y-axis symmetry,
and XY symmetry.
(1) Usual Repeat: In the case of multiple repetitions (when the parameters values "X
-direction repetitions" and " Y -direction repetitions" are bigger than 1), images
generated by all embroidery are the same;
For example: the original image of the displayed pattern is P, X-direction repetitions is
5 , and Y direction repetitions is 3. Then the group array generated by embroidery is
as follows:
P P P P P
P P P P P
P P P P P

(2) X -axis symmetry: In the case of multiple repetitions (when the parameters values
"X -direction repetitions" and " Y -direction repetitions" are bigger than 1), the image
produced by embroidery is p and q as alternate ;
For example : the original image of the displayed pattern is P , X-direction repetitions
is 5 , and Y direction repetitions is 3. Then the group array generated by embroidery is

第 114 页 共 218 页
as follows:
p q p q p
q p q p q
p q p q p

(3) Y -axis symmetry: In the case of multiple repetitions (when the parameters values
"X -direction repetitions" and " Y -direction repetitions" are bigger than 1), the image
produced by embroidery is p and b as alternate ;
For example: the original image of the displayed pattern is P , X-direction repetitions
is 5 , and Y direction repetitions is 3. Then the group array generated by embroidery is
as follows:
p b p b p
b p b p b
p b p b p

(4) XY symmetry: In the case of repeated repetitions, the pattern produced by

embroidery is p and d as alternate ;
For example: the original image of the displayed pattern is P , X-direction repetitions
is 5 , and Y direction repetitions is 3. Then the group array generated by embroidery is
as follows:
p d p d p
d p d p d
p d p d p

第 115 页 共 218 页
2.Priority: set horizontal or vertical as priority in repeated embroidery.
(1) Horizontal first: doing embroidery work in horizontal (X-direction) first during
repeated embroidery, then embroider one row after another;
(2) Vertical first: doing embroidery work in vertical (Y-direction) first during repeated
embroidery, then embroider one column after another.
The schematic diagram is as follows:

Horizontal Embroidery first Vertical Embroidery first

F F F F F F
(9) (8) (7) (9) (6) (3)

F F F F F F
(6) (5) (4) (8) (5) (2)

F F F F F F
(3) (2) (1) (7) (4) (1)

1. X-Repetitions: set patterns quantity to be embroidered repeatedly in X direction,

that is, columns of patterns produced by embroidery, and the set value is between

1~200 ;

2. Y-Repetitions: set patterns quantity to be embroidered repeatedly in Y direction,

that is, rows of patterns produced by embroidery, and the set value is between 1~200 ;

3. X -direction repeat distance: Distance between two pattern-edges in X -direction.

Input value is between -30000~30000. The unit is 0.1mm , that is, 200 means 20mm .
The schematic diagram of X direction repeated spacing is as follows:
When X- direction repeated spacing When X- direction repeated spacing
+10mm -10mm

第 116 页 共 218 页
 F. ..
反复方向

花样起点 F. F. 反复方向

F. . 花样起点
反复间距 反复间距

+10mm -10mm

4. Y -direction repeat distance: Distance between the Y- direction edges of two

designs, input value is between -30000~30000. The unit is 0.1mm, that is, 200 means
20mm . The schematic diagram of Y-direction repeated spacing is as follows:
When the Y- direction repeated spacing When the Y- direction repeat spacing is
+15mm -15mm

F. F. ..
花样起点

F. F.
反复方向 反复方向
反复间距 +15mm 反复间距 -15mm

.. 花样起点

7.2 Description of Main Boards Control repeat mode

Click “Repeat Embroidery” from “Embroidery Function”, as shown in Fig. 7-5.

第 117 页 共 218 页
 Fig. 7-5 Embroidery function setting interface

Then enter Repeated embroidery setting interface, as shown in Fig. 7-6 below .

Fig. 7-6 Repeated embroidery parameter setting interface

Para. Name Function Description

X-Repetitions The value of repetitions corresponds to patterns quantity at X

第 118 页 共 218 页
 direction, 0 and 1 represents no repetitions.

X-Repetition Distance between the two patterns starting points at X direction.

spacing

Y-Repetition The value of repetitions corresponds to patterns quantity at Y

direction, 0 and 1 represents no repetitions.

Y-Repetition Distance between the two patterns starting points at Y direction.

spacing

Priority order Prior to embroider in X direction or in Y direction first.

Chapter 8 _ Super User Interface Description

Super user refers to the user with the highest authority of the system. Superusers
are often referred to as administrators or ROOT users. Set parameter configuration,
etc. (Customers are prohibited from modifying without manufacturer’s permission)
The following describes Super User configuration password and basic functions.
Find and enter the super user management interface from Main Interface, shown as
Fig. 8-1. The super user password is 262574. And the highest authority password is
951103, which can modify more things.

第 119 页 共 218 页
 Fig. 8-1 Enter the password interface before entering the super user

After input the password, then enter the super user interface, as shown in Fig. 8-2
below. Users can set some highest authority functions in this interface.

Fig. 8-2 (1) Super user interface

第 120 页 共 218 页
Fig. 8-2 (2) Super user interface

Fig. 8-2 (3) Super user interface

第 121 页 共 218 页
 Fig. 8-2 (4) Super user interface

8.1 HMI configuration Instructions

Fig. 8-3 Super User Interface

Click HMI configuration as shown in Fig. 8-3, and do the settings for the interface,
as shown in Fig. 8-4.

第 122 页 共 218 页
Fig. 8-4 (1) Interface configuration

Fig. 8-4 (2) Interface configuration

第 123 页 共 218 页
 Fig. 8-4 (3) Interface configuration

There are two resolutions, one is 1024×600, and the other is 1920 × 1080. The

communication method is fixed as network port communication, the machine type is

fixed as 000 embroidery machine, and the product type is fixed as pure flat
embroidery machine. The remaining functions are config.d according to the user's
requirements, such as whether there is a function of beads embroidery; click YES if
have, otherwise click NO. Click after setting is complete.

8.2 Description of interface debugging mode

Click the interface debugging mode from super user, as shown in Fig. 8-5 below.

第 124 页 共 218 页
 Fig. 8-5 interface debugging mode

After clicking, the system will pop up a dialog box "whether to enter the debugging
mode", as shown in Fig. 8-6 below

Fig. 8-6 Enter the debug mode interface

Click to enter the debugging mode. In the debugging mode, no need

password every time when doing operation the Super User.

第 125 页 共 218 页
8.3 Description of CSV file

Fig. 8-7 Super User Interface

Deleting configuration Files, importing CSV files, and deleting CSV files in the super
user interface are all well-config.d before leaving the factory, please do not operate at
will.

8.4 Reset Install and Debug Progress

Click to reset the installation and debugging progress, as shown in Fig. 8-8 below

Fig. 8-8 Super User Interface

第 126 页 共 218 页
System will pop up a prompt as shown in Fig. 8-9 below. Notify the user that the reset
was successful.

Fig. 8-9 Reset Install and Debug progress interface

Click to reset the installation and debugging progress. It’s mainly used in
Internet monitoring.

8.5 Explanation of machine parameters

第 127 页 共 218 页
 Fig. 8-10 Machine parameter setting interface

After the parameters are restored to default, set the machine parameters including Nos
of EMB Heads, nos of needles per EMB head, thread tension-base, and head-locking
mode according to the machine configuration. Other parameters keep same as
config.d as EXW factory.

Para. Name Function

Nos of EMB Heads Number of flat embroidery heads, which has been
config.d before EXW factory.
Nos of needles per EMB Set the number of needles for each head of the flat
head embroidery head, which has been config.d before leaving
the factory.
Thread-trimming method There are two methods: static thread trimming and
dynamic thread trimming. The default is dynamic thread
trimming. It has been config.d before leaving the factory.
Static thread trimming mode is not recommended.
Thread-Tension Base There are two types: model II Individual Tension Base
and III Individual Tension Base, the default is II
Individual Tension Base
, which has been config.d before EXW factory.
EMB head-locking There are two modes for flat embroidery: motor lock and
electromagnet lock, switchable according to the actual
situation, and it has been config.d before EXW factory
X-Zero sensor According to the actual situation, it can be set. Click Yes
if has, or No if hasn’t. It has been config.d before EXW
factory.
EMB color-changing There are two modes for flat embroidery color-changing:
method automatic and manual. Automatic changing means that
after detecting one needle position completes, the

第 128 页 共 218 页
 machine automatically moves to the next needle position.
In manual mode, the machine does not automatically
change colors and waits for manual pulling the lever to
proceed to the next step.
Repeat embroidery Optional modes: manual start and automatic start,
automatic or not
Whether to pause the Click Yes, then the starting point of repeated embroidery
start-point of repeat will be paused; click No, then it will not be paused
embroidery
EMB jump-stitch Flat embroidery jump-stitch frame-changing stitches, if
frame-changing stitches inputting 0 stitches, it means no shift. If the number of
consecutive jumping stitches is bigger than the set value,
the jumping stitches will shift the frame. When jumping
stitches shift the frame by stitches number, the stitches
jump distance is bigger than the set value, jump-stitches
will shift the frame.
Frame-changing distance The distance of frame-changing for jump-stitch
of jump-stitch
X frame sensor zero X frame sensor coordinates, the value set when homing
coordinate
Y frame sensor zero Y frame sensor coordinates, the value set when homing
coordinate
X-axis zero In order to make the machine position moving on the X
compensation axis more accurate
Y-axis zero In order to make the machine position moving on the Y
compensation axis more accurate
EMB spindle parking The parking angle of the flat embroidery main shaft,
angle usually refers to the angle when flat embroidery main
shaft stops normally.

第 129 页 共 218 页
EMB spindle zero The zero-finding compensation of the flat embroidery
compensation main shaft is to correct the error of the main shaft to
ensure that the embroidery machine stops more accurately
when the main shaft returns to zero.
Movable area ( X- ) The maximum value of machine moving range at the
negative direction of X-axis. The X- axis is usually a
horizontal movement axis, and its positive direction is the
positive X direction on the right side when facing the
screen.
Movable area ( X+ ) The maximum value of machine moving range at the
positive direction of X-axis.
Movable area ( Y- ) The maximum value of machine moving range at the
negative direction of Y-axis.
Movable area ( Y+ ) The maximum value of machine moving range at the
positive direction of Y-axis.
EMB Working area (X-) The maximum value of the flat embroidery head working
range at the negative direction of the X axis.
EMB Working area (X+) The maximum value of the flat embroidery head working
range at the positive direction of the X axis.
EMB Working area( Y- ) The maximum value of the flat embroidery head working
range at the negative direction of the Y axis.
EMB Working area (Y+) The maximum value of the flat embroidery head working
range at the positive direction of the Y axis.
EMB head offset X The distance between the two heads, based on one head.
EMB head offset Y The distance between the two heads, based on one head.
EMB head spacing Flat embroidery head spacing refers to the distance
between two embroidery heads. In the design of
embroidery machines, the size of head spacing is
generally fixed, and usually determined by the machine

第 130 页 共 218 页
 structure and embroidery head size, etc..
XY start-stop speed XY start-stop speed is the speed of start and stop in the
direction of X axis and Y axis.
XY zeroing running XY zeroing running speed, is the speed of the machine
speed moving on X-axis and Y-axis during returning to zero
position. Homing to zero position is mainly to ensure the
machining accuracy, so zeroing running speed needs to be
controlled within an appropriate range.
XY no-load running XY no-load running speed is the frame automatic moving
speed speed, with moving at the direction of X axis and Y axis.
XY walking acceleration XY travel acceleration is the acceleration in the X- axis
and Y -axis directions. Acceleration is the amount by
which an object's speed increases per unit of time.
XY braking acceleration XY braking acceleration is the deceleration movement
when braking in the X- axis and Y -axis directions. At this
time, the acceleration during braking needs to be set. The
magnitude of the acceleration determines the speed and
smoothness during braking process.
XY max. moving speed XY maximum moving speed is the maximum achievable
moving speed in the directions of X- axis and Y- axis.
XY manual moving It is the manual operation speed, the first level speed of
speed 1 Sudoku area manual adjustment.
XY manual moving It is the manual operation speed, the second level speed of
speed 2 Sudoku area manual adjustment.
XY manual moving It is the manual operation speed, the third level speed of
speed 3 Sudoku area manual adjustment.
Spindle start-stop speed Speed when the spindle starts working and finishes
processing.
Spindle zeroing speed Speed of the spindle when returning to zero.

第 131 页 共 218 页
Spindle rotation speed Speed when the main shaft running
Spindle running It’s the acceleration when the spindle is running, that is,
acceleration the time and force required for the spindle to reach the
actual working speed from a static state.
Spindle braking It refers to the acceleration required when the spindle
acceleration stops, that is, the time required for the spindle to stop
from the running state to the static state.
Max. EMB spindle The maximum acceleration of the flat embroidery main
acceleration shaft, the limit of the maximum acceleration when the
main shaft is accelerated in the flat embroidery machine.
Spindle manual moving Speed set when the manual wheel adjusts the spindle
speed position.

8.6 Explanation of working parameters

第 132 页 共 218 页
 Fig. 8-14 Working parameter setting interface

Click and enter "Working Parameters" interface, as shown in Fig. 8-14.

The following table is interpretation of the working parameters:
Parameter name Interpretation
Two modes are: by stitches and by distance.
By distance: frame will shift when the jump-stitch
Frame-changing mode
exceeds the set distance.
of Jump-stitch
By stitch: frame will shift when the jump-stitch exceeds
the set stitches number.
Set the rotation speed of the flat embroidery main shaft
Spindle corner speed
when passing the corner.
Deceleration minimum The angle of the spindle during deceleration must be
deviation angle bigger than the minimum deviation angle
EMB spindle working Spindle motor running speed during flat embroidery
speed
EMB spindle speed Running speed of the spindle back stitching during flat
embroidery
EMB starting spindle Slow moving speed when the main shaft starts during

第 133 页 共 218 页
slow-moving speed flat embroidery
Max. spindle speed of Maximum spindle speed during jump stitching in flat
EMB jump stitch embroidery
EMB work acceleration Acceleration during working of flat embroidery main
shaft
EMB frame-moving Maintaining-angle of moving frame in flat embroidery
duration angle
Maximum speed limit of Maximum speed limit of moving speed in flat
EMB moving frame embroidery
When flat embroidery starts embroidery, if it is allowed
EMB thread clamping of
to clamp the thread or not.
start-stitch Enable
This is a switch, default is "off"; "on" means to enable.
When flat embroidery starts embroidery, if it is allowed
EMB thread-buckling of
to buckle the thread or not.
start-stitch Enable
This is a switch, default is "off"; "on" means to enable.
Emb. thread-break No detection when thread-breakage in flat embroidery
detect. Disable
The rotation speed of the flat embroidery main shaft
Thread trimming speed
during thread-trimming.
of EMB spindle
Input value is between ( 1~150 ), unit is r/min .
Whether thread trimming is allowed during flat
embroidery.
EMB thread-trim Enable
Optional values are: no thread trimming/ automatic
thread trimming/ last trimming/ data trimming
Frame moving direction during thread trimming in flat
embroidery.
Frame direction in EMB
Optional values are: left / forward / right / backward /
thread-trim
non-moving. Default is backward, for static trimming
operation.

第 134 页 共 218 页
Frame-moving Frame moving distance during thread trimming in flat
displacement in EMB embroidery, for static thread trimming operation.
thread-trim Input value is between ( 0.01~10.00 ) mm.
Thread-distribute angle Thread distributing angle during dynamic thread
in EMB dynamic thread trimming in flat embroidery
trimming Input value range is between ( 0.00~360 ) degrees.
Thread-clamp angle in Thread clamping angle during dynamic thread trimming
EMB dynamic in flat embroidery.
thread-trim Iinput value range is between ( 0.00~95 ) degrees.
The angle of hooking knife stretching-out during
Hook Out Angle in EMB
dynamic thread trimming in flat embroidery.
dynamic thread-trim
Input value range is between (0.00~360.00) degrees.
Hook Back Angle in Angle of hooking knife taking back during dynamic
EMB dynamic thread trimming in flat embroidery.
thread-trim Input value range is between ( 0.00~360.00 ) degrees.
Completion angle in Angle of scissors completing movement during dynamic
EMB dynamic thread thread trimming in flat embroidery.
trim Input value range is between ( 0.00~360.00 ) degrees.
Stitches qty. detected during upper thread breakage in
EMB upper thread-break
flat embroidery.
detected stitches
The input value range is between ( 0~50 ).
EMB bobbin Stitches qty. detected during bobbin thread breakage in
thread-break detected flat embroidery.
stitches The input value range is between ( 0~50 ).
Reminder function when changing the bobbin in flat
embroidery
EMB Bobbin change
Optional values are: count by pieces/ immed.remind by
reminder function
length / disable this function / delay remind by length.
Just set the pieces of bobbin changing in counting by

第 135 页 共 218 页
 pieces; or set the length of bobbin changing in counting
by length in flat embroidery.
EMB bobbin thread Bobbin thread length of flat embroidery
length Input value range is between (0.00~900,000.00)mm.
Correction amount of bobbin thread per stitch in flat
EMB Bobbin thread
embroidery.
correction amt per stitch
Input value range is between ( 0.00~900,000.00 ) mm .
Bobbins qty counted by pieces in flat embroidery
EMB bobbins qty by
working.
pieces
Input value is between (0~999,999,999).
Same color pause in Machine will pause if same color during flat embroidery
EMB color-change color changing.
Appliqué Offset Method Including offset distance and offset point
Cap frame in-place Detect whether the embroidery frame is in place
detection Enable
Advance deceleration Stitches that require to reduced speed when parking or
stitches corner turning.
The mending methods of flat embroidery have: manual
EMB mending method mending/ automatic mending/ all heads mending/ no
mending
EMB thread-hooking Delay time of thread hooking in flat embroidery.
Delay Input value range is between ( 0~100 ).
Scope of thread-hooking contraction during flat
EMB thread-hooking
embroidery.
contraction
The input value range is between ( 0~70 ).
No stitches detect. when No detection of stitches when flat embroidery upper
EMB upper thread starts thread starts.
No stitches detect. when No detection of stitches when flat embroidery bobbin
EMB bobbin thread thread starts.

第 136 页 共 218 页
starts
manual mending/ automatic mending/ all heads
Mending methods
mending/ no mending
Mending Advance Number of stitches in mending embroidery completion
Ending Stitches in advance.
EMB mending advance Stitches before mending when thread-breakage.
stitches Input value range is between ( 0~10 ).
Boring needle position Position for the boring needle
Position difference of boring needle position to the flat
Boring Offset amt. embroidery needle position, the boring needle position
will protrude from the flat embroidery needle position.
When turn " ON " boring offset enable, the boring
Boring Offset Enable needle position will automatically move according to
the value of boring offset during machine working.
This is a switch. Default is " off " state, when it is " on" ,
XY movement limit
it means that XY movement limit enables.
This is a switch. Default is " off " state, when it is " on" ,
EMB bar-drop limit
it means that embroidery bar-dropping enables.
Output preset The input value range is ( 0~999,999,999 ).
Parking location after Optional values are: start point / offset point / current
completion position.
Valid offset point Optional values are: X valid /Y valid /XY valid /
coordinate invalid.
Offset point X X coordinate of the offset point. Input value range is
coordinate ( -9999,999.99~9999,999.99 ) mm .
Offset point Y Y coordinate of the offset point . Input value range is
coordinate ( -9999,999.99~9999,999.99 ) mm .
Valid feeding point Optional values are : X valid /Y valid /XY valid /
coordinate invalid.

第 137 页 共 218 页
X coordinate of feeding Input value range is between
point (-9999,999.99~9999,999.99) , and unit is mm .
Y coordinate of feeding Input value range is between
point (-9999,999.99~9999,999.99) , and unit is mm .
The options are: no oiling / oiling as per working hours /
oiling as per working stitches /continuous oiling.
“Oiling as per working hours” needs to match with
Oiling Method
“oiling stitches interval”.
“Oiling as per working stitches” needs to match with
“oiling hours interval”.
Set a value of stitches interval, when the machine
reaches the value, it will oil automatically.
Oiling Stitches Interval
When choosing the oiling method as per working
stitches, it need to set the stitches interval.
Set a value of hours interval, when the machine reaches
the value, it will oil automatically.
Oiling Hours interval
When choosing the oiling method as per working hours,
it needs to set the hours interval.
Oiling duration The duration during oiling the machine.
Rotary hook oiling Duration for rotary hook oiling
duration
Air duration during The air storage duration during oiling the machine.
oiling Sectional oiling delay (to avoid insufficient pressure).
Boot bus detection Boot bus does not detect
disable
Air pressure safety input Air pressure safety input function open
Enable
Light curtain safety Light curtain safety input function open
input Enable

第 138 页 共 218 页
Material-short detection Material in shortage detection function open
Enable
Bus shield Two options: Shielded / unshielded
This is a switch. The default is " off " state. Only when
Needle speed limit
it is " on ", the value of the needle position speed limit
Enable
setting will really take effect.
This is a switch to check whether the hook knife returns
to its original position. Default is "OFF" state.
Centralized thread-hooking means Enable; individual
hooking means disable.
Hook knife detection If it is "ON", after the thread trimming is completed, it
Enable will detect whether the hook knife returns to its original
position. If it is not in place, it will report 'the hook
knife not returns'; if the parameter is " off ", it will not
detect whether the hook knife is in place after thread
trimming.
After selecting the pattern file, machine will start
Set the start embroidery stitching at the original place when turning on, and take
point automatically the current frame position as the start-point. (this
function can only be enabled when stitches index is 0.)
The maximum spindle speed allowed for needle bar 1. 0
means that the spindle speed is not limited. It needs to
Needle 1 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 2. 0
means that the spindle speed is not limited. It needs to
Needle 2 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
Needle 3 speed limit The maximum spindle speed allowed for needle bar 3. 0

第 139 页 共 218 页
 means that the spindle speed is not limited. It needs to
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 4. 0
means that the spindle speed is not limited. It needs to
Needle 4 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 5. 0
means that the spindle speed is not limited. It needs to
Needle 5 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 6. 0
means that the spindle speed is not limited. It needs to
Needle 6 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
Needle 7 speed limit The maximum spindle speed allowed for needle bar 7. 0
means that the spindle speed is not limited. It needs to
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 8. 0
means that the spindle speed is not limited. It needs to
Needle 8 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 9. 0
means that the spindle speed is not limited. It needs to
Needle 9 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 10.
Needle 10 speed limit
0 means that the spindle speed is not limited. It needs to

第 140 页 共 218 页
 match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 11.
0 means that the spindle speed is not limited. It needs to
Needle 11 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 12.
0 means that the spindle speed is not limited. It needs to
Needle 12 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 13.
0 means that the spindle speed is not limited. It needs to
Needle 13 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 14.
0 means that the spindle speed is not limited. It needs to
Needle 14 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".
The maximum spindle speed allowed for needle bar 15.
0 means that the spindle speed is not limited. It needs to
Needle 15 speed limit
match with "needle position speed limit enable". Needle
position speed limit can only be set when it is "ON".

8.7 Flat embroidery headboard parameters interpretation

Click “EMB Headboard parameters” in Super User interface, shown as Fig. 8-16.

第 141 页 共 218 页
 Fig. 8-16 Super user interface

Fig. 8-17 EMB headboard parameters interface

第 142 页 共 218 页
 Fig. 8-18 EMB headboard parameters interface

Fig. 8-19 EMB headboard parameters interface

Fig. 8-17, 8-18 and 8-19 as above are parameters of flat embroidery headboard.
Parameter Name Function Description
Two-way electromagnet The time for the two-way electromagnet to energize;
hold time long-time energizing will burn out the electromagnet.

Headlock motor Headlock motor segmentation amount

第 143 页 共 218 页
segmentation
Headlock motor work The operating current size of the headlock motor
current
Headlock motor locking Locking current size of the headlock motor
current
Headlock motor stop Stop current size of the headlock motor
current
Head-locking automatic Head-locking has continuous power supply / automatic
power off power off
Headlock motor work Operation angle of headlock motor
angle
Headlock motor start Angle to skip when the headlock motor starts to work
skipping angle
Headlock motor start Starting frequency of headlock motor
frequency
Headlock motor work Running frequency of headlock motor
frequency
Headlock motor accel. Acceleration of headlock
Thread-hook motor Segmentation amount of thread-hooking motor
segmentation
Thread-hook motor work The operating current size of the thread-hooking motor
current
Thread-hook motor Locking current size of the thread-hooking motor
hooking current
Thread-hook motor stop Stop current size of the thread-hooking motor
current
Thread-hook automatic The hook thread is divided into continuous power supply
power off / automatic power off
Thread-hook motor Thread-hooking motor running angle

第 144 页 共 218 页
running angle
Thread-hook motor start Skipping angle when Thread-hooking motor starts
skipping angle
Thread-hook motor start Starting frequency of thread-hooking motor
frequency
Thread-hook motor work Running frequency of thread-hooking motor
frequency
Thread-hook motor Acceleration of thread-hooking motor
acceleration
Thread-hook relax angle Relaxing angle of thread-hooking
One-way electromagnet One way electromagnet PWM shutdown time
PWM shutdown time
Headlock type Options are: no locking / stepping motor locking /
electromagnet locking
Q1 function type Headlock electromagnet / laser light out control
Q2 function type One-way thread-clamping electromagnet/ laser
positioning light
Laser positioning light off Laser positioning light turn-off delay (this function will
delay be shown in headboard parameters only when it’s set in
Interface Setting)
Bead out completion Completion angle when loose beads fed-out. Finishing
angle angle of loose beads and bead discharge (this function
will be shown in headboard parameters only when it’s set
in Interface Setting)
Simple chenille action Completion angle of simple chenille action (this function
completion angle will be shown in headboard parameters only when it’s set
in Interface Setting)
Simple chenille swing Simple chenille swing(this function will be shown in
headboard parameters only when it’s set in Interface

第 145 页 共 218 页
 Setting)
Sequin out completion Completion angle when sequin fed-out (this function will
angle be shown in headboard parameters only when it’s set in
Interface Setting)
Sequin cut close Completion angle when sequin-cut knife-closing (this
completion angle function will be shown in headboard parameters only
when it’s set in Interface Setting)
Sequin cut opening angle Opening angle of sequin cutting (this function will be
shown in headboard parameters only when it’s set in
Interface Setting)

8.8 Description of Pattern Parameters

Fig. 8-20 Pattern parameter setting interface

Click and enter "Pattern Parameters" interface, as shown in Fig. 8-20:

Parameter name Interpretations
Stitch-locking Times of stitches-locking before embroidery starts.
times Input value range is between ( 0~10 ).
Locking Stitches Number of stitches for locking before embroidery starts.

第 146 页 共 218 页
 Input value range is between ( 0~10 ).
Lock Stitch The length of the interval between two stitches.
Length Input value range is between ( 0.00~1.00 ) mm .
X- direction compensation is a small displacement adjustment in
the horizontal direction, so that the system can reach the target
X- compensation
position more accurately.
The input value is between (-1.00~1.00)mm .
Y -compensation is a small displacement adjustment in the
Y- compensation vertical direction so that the system can reach the target position
more accurately. The input value is between (-1.00~1.00)mm .
Zoom in or out to the pattern at X direction. Input value from the
number key, which is between 50 and 200. Inputting 100 means
X- magnification
same size as the original, 50 means half of the original size
( 50% ), and 200 means double the size ( 200% ).

8.9 Description of traversal settings

Click and enter traverse settings, after the machine is powered on for the first time, all
traverses need to be performed. As shown in Fig. 8-21 below.

第 147 页 共 218 页
 Fig. 8-21 Traverse Setting interface

If the machine parameters are set to 10 heads, there will be 1-N, 2-N, ... 9-N,
10-N signs below, click “Nos of traversals”, change the single traversal to all traversal,
click all the machine heads and all will turn red, and turn the switches on the heads,
the LED light will flash red and green alternately, when 1-N, 2-N, etc. on the screen
change to 1-Y, 2-Y, etc., then traverse successfully done. (Note: When turning the
head switch, need to wait for the previous head to flash then proceeding to the next
head traverse.) As shown in Fig. 8-22. After all heads traversal completed, all heads
lights will go out, and then automatically turn on sequentially.

第 148 页 共 218 页
 Fig. 8-22 Single traversal function setting interface

If machine needs to replace a board, it needs to be traversed separately after the

replacement, click "Single Traverse". set the head which needs to traverse, click
, and the head light will turn red, then turn up the switch of this head, all heads
lights will flash red and green in sequence. After all the lights are off, traverse done.
The machine head information will appear at the bottom of the interface.

8.10 Explanation of headboard bus detection

第 149 页 共 218 页
 Fig. 8-23 Headboard bus detection interface

Click “Headboard bus detection”, as shown in Fig. 8-23 above,

Fig. 8-24 Headboard bus detection interface

System will pop-up “Whether to perform head board bus detection?” shown as in
Fig. 8-24 , click , the lights on the headboard will light up one by one. If the
headboard lights are off, it means abnormality in the communication, and a bus error
pop-up window will display in the interface. It reflects the communication status
between peripheral boards. Click to cancel the operation.

第 150 页 共 218 页
8.11 Description of automatic soft limit setting

Fig. 8-25 Automatic software limit setting interface

Click " Auto Set Soft Limit ", system will remind “ Machine is going to move,
please pay attention to safety!” as shown in Fig. 8-26, click , X, Y will return to
zero first, and the machine will move to the limit sensor and calculate the soft limit
value automatically. Note: Adjust the position of the sensors in advance, and adjust
the sensor to both edges to prevent limit prematurely.

Fig. 8-26 Automatic software limit setting interface

第 151 页 共 218 页
Note: The system soft limit has been config.d before leaving the factory, no need to
change

8.12 Explanation of Flat Embroidery HeadLock Test

Fig. 8-27 Flat embroidery lock test interface

Click and enter "EMB Headlock test" interface, then click "Simulated Spindle
Speed " , and input the simulation speed in the pop-up. This function is available only
when the head locking is motorized. Shown as in Fig. 8-27 .

第 152 页 共 218 页
 Fig. 8-28 Simulated spindle speed interface

Click after inputting the required speed, as shown in Fig. 8-28 above.

Fig. 8-29 Flat embroidery lock test interface

Then follow the steps and click shown as in Fig. 8-29, and the flat

embroidery headlock test will start.

8.13 Description of Flat Embroidery Hook Knife Test

Fig. 8-30 EMB hook knife test interface

第 153 页 共 218 页
 Fig. 8-31 EMB Hook Knife Test Interface

Click “EMB Hook-knife Test”, as shown in Fig. 8-30 above, and system will
pop-up “Hook knife is going to move, please pay attention to safety!” Press ,
the hook knife will start to move, and press , the hook knife will stop moving.
As shown in Fig. 8-31 above .

8.14 Explanation of pattern clearing

Fig. 8-32 Pattern clearing interface

第 154 页 共 218 页
 Fig. 8-33 Dialog box of pattern clearing interface

Click “Pattern Clear”, system will pop-up “Whether to clear patterns?”, shown as in

Fig. 8-32 and 8-33. Click to clear all patterns in the system, and click to

cancel the operation.

8.15 Interface Decryption

Fig. 8-34 Interface decryption dialog box

When click “HMI decrypt”, system will require to input the password, shown as
第 155 页 共 218 页
in Fig. 8-34. After entering the password, it can be decrypted and connected with the
display interface of the motherboard. (Disable)

8.16 Modify Level 1 Password

Fig. 8-35 Modify Level 1 Password pop-up

Click and enter “Modify Level 1 Password”, interface will popup for the new

password, shown as in Fig. 8-35. Input new password and confirm , then

password is successfully modified. Click to cancel the operation.

第 156 页 共 218 页
8.17 IoT configuration

Fig. 8-36 Internet of Things setting interface

Click and enter “IoT configuration” interface, find “Network settings” ,as shown in
Fig. 8-36. It will enter the network setting sub-interface as in Fig. 8-37.

Fig. 8-37 Network setting interface

第 157 页 共 218 页
 Fig. 8-38 Server IP setting interface

Set the IP address, fist click the server IP setting, system will pop-up to require

the new IP address as shown in Fig. 8-38. Click to complete the operation, or

click to cancel the operation.

(The IP address of the IoT server and the IP address of the network management
cannot be the same.)

第 158 页 共 218 页
8.18 Moving frame angle setting

Fig. 8-39 Moving frame angle setting interface

Fig. 8-40 Moving frame angle setting interface

After the machine is powered on, click “Frame Angle Setting”, and the data
shown in Fig. 8-40 above will be displayed on the screen. If a certain speed is not
ideal, the XY value of the frame-moving angle can be adjusted minutely.

第 159 页 共 218 页
8.19 Gear ratio test of main shaft for flat embroidery

Fig. 8-41 EMB Spindle Gear Ratio Test

Click “EMB Spindle Gear Ratio Test”, system will pop-up “whether to test the gear
ratio of the main shaft of flat embroidery” shown as in Fig. 8-41, click , if the
gear ratio is normal, then the status bar at the bottom will display that the gear ratio of
flat embroidery is normal. If the gear ratio is abnormal, an alarm message window
will pop up. Click to cancel the operation.

第 160 页 共 218 页
8.20 Set the workable area for flat embroidery

Fig. 8-42 EMB setting workable area

Click to set the workable area of flat embroidery, and a pop-up will be shown in Fig.
8-43.

Fig. 8-43 Interface of EMB setting workable area

There are four buttons X+, X-, Y+, and Y- to operate. Machine head will not
move with the buttons. Click the direction keys to control the frame movement. When

the embroidery frame moves to a suitable position, Click , then this position
第 161 页 共 218 页
is the maximum value of X+, X-, Y+, Y- workable area. (Note: These four working
areas are set sequentially and cannot be completed at the same time) Click to

cancel the operation.

8.21 Import and export of moving frame parameters

Fig. 8-44 Parameter import interface

Before importing parameters, you need to insert a USB disk. If no USB disk
inserted, click the "Parameter Import" button, and a prompt "No USB disk detected!"
will pop up, as shown in Fig. 8-44.
第 162 页 共 218 页
 Fig. 8-45 The interface of successful importing of frame parameters

After inserting the USB disk and clicking the "Parameter Import" button, the
interface will display the file with the name of frameparadat in the USB disk. Select
the parameter file to be imported, as shown in Fig. 8-45.

Fig. 8-46 Parameter export

Before exporting parameters, you need to insert a USB disk. If no USB disk is
inserted, click the "Parameter Export" button, and a prompt "No USB disk detected!"
will pop up, as shown in Fig. 8-46.

第 163 页 共 218 页
 Fig. 8-47 Parameter export

After inserting the USB disk, click the "Parameter Export" button, and a
"Parameter Export Successful" prompt will pop up. Select the parameter file to be
exported, and click to complete the parameter export. The interface is shown in
Fig. 8-47.

8.22 Delete pattern fcg file

Fig. 8-48 Clear Pattern fcg file

This has been well-configured before EXW factory. Not allowed to operate this
without manufacturer’s permission.

第 164 页 共 218 页
Chapter 9 Wireless Pattern Transmission Operation
Instructions
The "wireless pattern transfer" operation is a data transmission method
realized by wireless communication technology, and is usually used to transfer data or
files between devices. Turn on the device that needs to transmit data and the device
that receives data, make sure they are both connectable and support the same wireless
communication protocol. Select data or files to be transferred from the sending device,
usually by long pressing the file and selecting an option such as "Share" or "Send".
“Wireless Pattern Transfer” or “Wifi” can be found in the menu, some interface are
slightly different for different devices and operation systems. Search for devices that
can be connected around and select one to receive data. The wireless pattern transfer
operation needs to establish a stable connection between the transmitting devices.

9.1 Operation instructions for wireless pattern transfer

1. Click << Auxiliary Function >> on the < Main Interface > , and find
<<<WIFI>>> . As shown in Fig. 9-1 .

Fig. 9-1 WIFI interface

Select the required WIFI (same wifi network as the machine), see Fig. 9-2 below .

第 165 页 共 218 页
 Fig. 9-2 WIFI connection display

Click Dynamic IP , and the IP address will be displayed . As shown in Fig. 9-3 below .

Fig. 9-3 Dynamic IP display

Set the dynamic IP, and set Static IP in the same gateway.
第 166 页 共 218 页
2. Open the software

Click the connect button as shown in Fig. 9-4

Fig. 9-4 Software interface

Set the static IP and click . As shown in Fig. 9-5. (No need too set the port)

Fig. 9-5 Set static IP interface

The toolbar functions description is as follows

1. Connect the operation box, after the connection is successful, it will show
“ Connected” at bottom-left corner.
2. Disconnecting status will also show at bottom-left corner the same.

第 167 页 共 218 页
3. Upload local files to the operation box;
4. Refresh local directory and operation box files list.
5. Return to the parent directory;
6. Directory selection;
7. The current directory;
The files in the operation box will be displayed only after the connection is
successful, and the buttons such as upload can be operated. Right-click the file to
delete the selected file. This transfer software only supports local uploading of files to
the operation box, and does not support directory uploading. Double-clicking local
files can also upload files. As shown in Fig. 9-6 :

Fig. 9-6 Software interface

第 168 页 共 218 页
Chapter 10 Basic Steps to Start Embroidery
10.1 Basic flow chart of embroidery
Following operation flow instructions for the operators who is the first time to
use the machine, and much helpful for the experienced operators to reconfirm the
operation process.

【Explanation】: The dotted line box indicates an operation that is not required every
time, you can skip it and go to the next step directly.

10.2 Power on and start

Connect the power supply to the electric control cabinet, press the green start
button on the front of the electric control box, and operation panel box will light on,
then enter the main interface to start the operation.
If there is no main switch, connect the power supply, and release all emergency
stop buttons, then press the green start button to start.

第 169 页 共 218 页
10.3 Use of Embroidery Operating Pull-Bar
Parking state: In the parking state, pull it to left to continue reversing, and the
embroidery frame will move synchronously, and pull it again to stop reversing; keep
pulling to left for quick-back, embroidery frame keeping still at this time, release the
bar to reverse the frame, and move to the corresponding position .
Working state: During the working state, hold the pulling bar to the right for
low-speed embroidery, release it to return to the original speed; pull the lever to the
left to stop embroidery;
Switching from Working state to the Simulating state: continuously pulling the bar to
the right, the stitches index will move forward rapidly, and after releasing, the index
stops, and the embroidery frame works to the corresponding position.

10.4 Instructions for mending embroidery

After the stitches index returns, pull the bar to mend the embroidery to the
thread-breakage head and other heads keep still. During the embroidery process, due
to thread breakage and other reasons, some machine heads may lose stitches. At this
time, the indicator light on the head will light up in red in time. Reverse the bar to the
missing stitching point, flip the switch upward, and the light will flash red and green
alternately, then pull the bar to start the mending embroidery. After mending job done,
light will not flash, and all the machine heads will work normally with green lights
on.

第 170 页 共 218 页
10.5 How to start embroidery for the first time
Computerized machine embroidery is based on the patterns stored in its memory.
Follow the steps below before using the new machine for the first time:
Step 1 : Import the patterns you need to embroider into the system memory with USB
disk, select and confirm the stitching pattern from the memory. (See 6.2
Pattern Parameter Setting in Chapter 6 for details )
Step 2 : Set embroidery parameters, mainly including:
(1) Setting of starting embroidery point and offset point (see Chapter 4 Shortcut
Function Introduction 4.9 Setting Embroidery Start-Point, 4.10 Back to Embroidery
Start-Point, 4.8 Back to Offset Point)
(2) Border checking, confirm the embroidery range of the pattern, to prevent frame
collision during embroidery. (For details, please refer to the detailed description of the
shortcut function in Chapter 4 , 4.11 Border Check)
(3) Setting of color sequence and color-changing start mode (see Chapter 6 Memory
Design Management 6.1 Pattern Setting, 6.3 Color Sequence Setting and 6.2 Pattern
Parameters for color change start mode)
(4) If color sequence is not set, Color changing and working head switching can be
done by manual. (see Chapter 6 Memory Pattern Tube 6.1 Pattern Setting 6.3 Color
Sequence Setting and 6.2 Pattern Parameters for color change start mode)
Step 3: After finishing the above steps, pull the embroidery bar under the table to the
right to start embroidering.

第 171 页 共 218 页
Chapter 11 Optional functions on flat embroidery
Now, Richpeace can provide many advanced attached devices and functions on
normal flat embroidery machine, such as automatic bobbin change function,
double-sequin device, single loose-beading device, simple chenille device, 8-sequin
device, double loose-beading device, tracing cording device and laser cutting device,
etc.

11.1 Operation instructions for Automatic Bobbin Change (ABC)

Power on the machine before operation. Find “Interface configuration” from
“Super User”, then find “ Whether there is ABC function”, turn the option from No to
Yes, and click to confirm, as shown in Fig. 11-1 below.

Fig. 11-1 Interface configuration interface

The interface pops up "Settings will take effect after HMI restarts". Confirm with
, and wait for the screen to exit the interface, then restart.

第 172 页 共 218 页
 Fig. 11-2 Restart interface

Click “Automatic Bobbin Change” function on the auxiliary function interface, as

shown in Fig. 11-3 below

Fig. 11-3 Interface configuration interface

Then a prompt will pop-up “Whether to set to change a bobbin automatically?” as

shown in Fig. 11-4.

第 173 页 共 218 页
 Fig. 11-4 Interface configuration interface

Set Parameters in automatic shuttle change,

Parameters Name Function Description

Automatic bobbin Options: No ABC / Others ABC / Richpeace ABC Ⅰ /

changer Richpeace ABC Ⅱ

Bobbins quantity Number of bobbins: Min. is 4 and max. is 6

Bobbin-changing Waiting time of the machine during bobbin changing;

time automatic bobbin-changing needs some time and machine
will wait until the bobbin-changing finishes; if the
bobbin-changing time is exceed the set parameter value, it
will report error.

Bobbin number 1-15 Bobbin corresponding to 1-15 Needle position

Function of automatic bobbin changing: can set as per patterns number or stitches
number. The automatic bobbin change device is installed below the rotary hook case,

第 174 页 共 218 页
according to the instruction, the manipulator next to it will take out the empty bobbin
case with bobbin from the rotary hook and put it to a vacant position of the ABC
roulette; the roulette motor will rotate and send the bobbin case and bobbin with
thread to the manipulator, and the manipulator takes and put it to the rotary hook. In
this way, embroidery efficiency can be greatly improved, saving much bobbin
changing time.
This section explains how to set the station number of the device (485
communication ) and some other uses , and the normal functions of the device ( such
as grippers , swing arms, etc. ) are not described here.
1. How to disable the device :
Click the all-head-changing button, and the digital tube will display - ; if you want to
make the device work again , click the initial button on this basis.
If the device is controlled by 485 communication mode, it is necessary to set the
station number ; if it is controlled by IO mode , this operation is not required.
2. How to enter the station number setting state :
Click the all-head-changing button three times continuously (the first time displays -,
the second time displays _, the third time enters the station number setting state ,
displays the current station number of the device , and the station numbers are sorted
from 0 to 9, and then from A to Z, Indicates 0-9, 10-35 respectively, where 0 indicates
that the device has no station number )
After the setting is completed , click the all-head-changing button again to save the
station number and restart the device
When in the state of setting the station number :
Gripper button : station number +10
Swing arm button : station number +1
Turntable button : station number -10
Single-change button : station number -1
Initial key : exit station number setting
After installing the automatic bobbin changing device, it is difficult to pick up and
put on the bobbins by manual, so add one button of automatic bobbin pick-up and
第 175 页 共 218 页
put-on.
Click the all-head-changing button, the digital tube displays - , then click the
single-change button to automatically take off the bobbin (when there is vacancy on
the roulette. )
Click the all-head-change button, the digital tube displays _ , then click the
single-change button to install the bobbin case with bobbin automatically ( when there
is bobbin in the roulette and no bobbin on the machine head. )

11.2 Description of Double Sequins Device

Power on the machine with sequin devices before operation. Find “Interface
configuration” from “Super User”, then find “ Whether there is sequin function”, turn
the option from No to Yes, and click to confirm, as shown in Fig. 11-5 below.

Fig. 11-5 Interface configuration interface

The interface pops up "Settings will take effect after HMI restarts". Confirm with
, and wait for the screen to exit the interface, then restart.As shown in Fig. 11-6.

第 176 页 共 218 页
 Fig. 11-6 Restart interface

Click “Sequin Device Type” and set it to double sequins, as shown in Fig. 11-7 below.

Fig. 11-7 Sequin setting machine parameter interface

Parameter name Function Description

Sequin device type There are double sequins and non-double sequins, choose
double sequins

第 177 页 共 218 页
Left Sequin A Double Sequin Left Sequin 1

left sequin B Double Sequin Left Sequin 2

1st sequin size at left 1st sequin size for left double-sequin device

2nd sequin size at left 2nd sequin size for left double-sequin device

Right Sequin A Double Sequin Right Sequin 1

Right Sequin B Double Sequin Right Sequin 2

1st sequin size at right 1st sequin size for right double-sequin device

2nd sequin size at right 2nd sequin size for right double-sequin device

Sequin device lift delay Delay and waiting time after sequin device lifting
operation. This parameter is depending on factory air
pressure and adjustment of valve on device; if device lifts
faster, parameter value can reduce; if lifting slowly, then
change the parameter bigger.

The double sequin device is controlled by the D46 board, and divided into left
double sequins and right double sequins.
During the debugging process, if you encounter the problem that the motor moves
in the opposite direction, please check whether the program version is correct (left
sequin motor and right sequin motor run in opposite directions)
Note:
1. The switch button does not work under the spindle dynamic state
2. The feeding button does not work in the automatic state
Switch button K1:
Self-reset button, when the button is moved up or down, the corresponding feeding
fork will be retracted, and when the button is released, the fork will be pushed out to
complete the sequin feeding out (if the parameter value of the sequin size is 0, the red
第 178 页 共 218 页
light will flash)
Switch button K2;
Non-self-resetting button, when the button is in the upper position, it is in automatic
state, the device lifting up and down according to the master control command, and
the green light is always on; when the button is in the lower position, it is in manual
state, the device is lowered, and the green light flashes; when the button is in the
middle, it’s disabled, device lifts at this time, and does not participate in work, green
light off.

11.3 Operation instructions of multi-sequin device

Use N8B to control multi-sequin device, currently it can control 8-sequin device.
Select non-double sequins in the sequin device type, as shown in Fig. 11-8 below .

Fig. 11-8 Machine parameter - 8-sequin setting interface

Parameter name Function Description

Sequin device type There are double sequins and non-double sequins, choose
non-double sequins

Left sequins A-H Left sequins 1 to 8 of 8-sequin device

第 179 页 共 218 页
1st -8th sequin size at left 1st to 8th sequin size for Left 8-sequin device

Sequin device lift delay Delay and waiting time after sequin device lifting
operation. This parameter is depending on factory air
pressure and adjustment of valve on device; if device lifts
faster, parameter value can reduce; if lifting slowly, then
change the parameter bigger.

Parameter setting instructions :

1. After power on, reset the motor to zero first, and then display CPXX after
successful zeroing, where XX is the current color sequence
2. Click MODE button to switch the digital tube display to PARA
3. Click SET button to enter the parameter setting
4. Click + or - button to modify the parameters, short-press the SET button to switch
the digit to be modified ( unit’s or ten’s ), and the modified digit will flash; if you are
not satisfied with the modified value and want to restore to the original value, press
and hold + or - button.
5. Short press the MODE button to switch the parameter type
6. P-XX indicates sequin out displacement of the current color sequence, Y-XX
indicates the vertical color-changing displacement of current color sequence , d-XX
indicates the current device type , and XX is the parameter value
7. After parameters modified, click PUSH button to feed out sequins, or press and

第 180 页 共 218 页
hold the LEFT or RIGHT button to make the vertical color change motor move to the
modified parameter position to check whether the parameters are applicable.
8. After current color sequence parameters modified, click LEFT or RIGHT button to
change the color, and the digital tube will flash shortly to display the color sequence
after color-changing, and the parameter value will also be switched synchronously ; at
this time, you can directly modify it without exiting
9. After modification , you can press and hold SET button to save the data.
10. If need to quit halfway, press and hold MODE button to exit the parameter setting.
Button Keys description :
1. UP/DOWN, Controlling device lifting up and down
2. LEFT, short press to switch to the previous color, and long press to reset the
horizontal color change motor to zero
3. RIGHT, short press to switch to the next color, long press for vertical color change
motor to return to zero
4. PUSH, when pressed, sequin feeding fork retracts, and sequin out when it lifted.
5. CUT, sequin cutter closes when pressed, and open when it lifted.
6. MODE, used to switch between working mode and parameter setting mode ;
When entering the parameter setting, short press to switch the parameter type (cycle
switching among sequin out displacement, longitudinal color change distance, and
device type ), long press to exit the parameter setting.
7. SET, if in parameter setting mode (digital tube displays PARA), short press to enter
parameter setting; during parameter setting, SET button can be used to switch the
unit’s and tens digits of the parameter value (the changed bit will flash ); long press
SET to save the parameters; and if the device type is changed , it will automatically
restart the operation.
8. + , during parameter setting, the current digit ( unit’s or ten’s ) of the parameter
value can be 1 plus when short-pressing; long press to restore to the original value
before modifying
9. SHIFT (-), during parameter setting, the current digit ( unit’s or ten’s ) of the
parameter value can be 1 minus when short-pressing; long press to restore to the
第 181 页 共 218 页
original value before modifying.

11.4 Operating Instructions for Single Beads Device

Power on the machine with beads devices before operation. Find “Interface
configuration” from “Super User”, then find “ Whether there is beads emb. function”,
turn the option from No to Yes, and click to confirm, as shown in Fig. 11-9
below.

Fig. 11-9 Interface configuration

The interface pops up "Settings will take effect after HMI restarts". Confirm with
, and wait for the screen to exit interface, then restart, as shown in Fig. 11-10.

第 182 页 共 218 页
 Fig. 11-10 Restart interface

Set the parameters in machine parameter configuration, as shown in Fig. 11-11.

Fig. 11-11 Beads emb. in Machine parameter setting interface

Parameter name Function Description

Left beads device A single beads emb. Device at left
Right beads device A single beads emb. Device at right
Beads device lift delay Delay and waiting time after beads emb. device
lifting operation. This parameter is depending
on factory air pressure and adjustment of valve
第 183 页 共 218 页
 on device; if device lifts faster, parameter value
can reduce; if lifting slowly, then change the
parameter bigger.
Max. speed of beads embroidery Max. speed of beads device in flat embroidery
Note: Single beads emb. device is controlled by D46 board, and different programs
for left device and right device.
Operating Instructions :
1.MODE: mode key, for working mode switching
Display " A ": automatic (auto) mode, green light on, device will work in the auto
mode during embroidery. It will display A when it is in working state.
Display " H ": manual (hand) mode, green light flashing, this mode is used for manual
debugging of device action.
Display " _ ": device doesn’t work, green light off.
Display " P ": parameter setting mode , green light off.
(When in parameter setting mode, you can click the MODE button to exit, and the
parameter value will not be saved at this time, but this modification is valid )
2. Up/down key: When in manual mode, it can control the lifting of device; when in
parameter setting mode, it can switch parameters (F1 light indicates that the current
parameter is the clamping force, and F2 light indicates that the current parameter is
the feeding speed )
3. OK key: When in manual mode, it can control the device to switch between
bead-out position, preparation position and bead extraction position; when in
parameter setting mode, it can enter to set parameter, click it again to save the
parameters and exit this mode.
4. ↓ key: In automatic mode or manual mode, it is for manual bead feeding; in
non-working mode, it is for bead-out motor test, and click again to stop the test; in
parameter setting mode, it is for reducing the parameter value.
5. ↑ key: When in automatic mode (not in the process of embroidery ) or manual
mode, it can stop feeding; when in non-working mode, it can reset the bead motor to

第 184 页 共 218 页
zero; when in parameter setting mode, it can increase the parameter value.
Debugging instructions :
When using the device for the first time , it is necessary to adjust the zero position of
the bead-out motor. Loosen the load side of the bead-out motor, and then reset the
bead-out motor through the keypad until the motor is zeroing successful, then push
the load side to the ready position and fix. This position is motor zero position.
Parameter Description:
F1 on: bead-clamping force, the bigger the value, the greater the force.
F2 on: feeding speed, the bigger the value, the faster the speed.

11.5 Operation instructions of Double Beads Device

Name Function Description
Left beads A Device A of double beads device at left
Left beads B Device B of double beads device at left
Right beads A Device A of double beads device at right
Right beads B Device B of double beads device at right
Bead device lift delay Delay and waiting time after simple chenille
device lifting operation. This parameter is
depending on factory air pressure and
adjustment of valve on device; if device lifts
faster, parameter value can reduce; if lifting
slowly, then change the parameter bigger.
Max. speed of beads embroidery Max. speed of beads device in flat embroidery
Note: The double bead device is controlled by N8B board, please check whether the
device type is correct after power on for the first time (see below for the method). If
the device type is incorrect, click any "↑" or "↓" button to switch the type. After
finishing, click the set button again, the device can change the types and restart
automatically. When in the parameter setting mode, you can switch Bead A
parameters or Bead B parameters.

第 185 页 共 218 页
Operating Instructions :
1.MODE: mode key, used to switch working mode.
The first digital tube displays :
Display " A ": automatic (auto) mode, device will work in the auto mode during
embroidery. If the machine is in the working state, it will display A.CP.X (X
represents the current color sequence )
Display " H ": manual (hand) mode, used for manual debugging of device action.
Display " _ ": device doesn’t work.
Display " P ": parameter setting mode.
2. Up/down key: Control the device lifting up and down in manual mode.
3. OK_A key: When in manual mode, it can control the A bead-out motor to switch
between bead-out position, preparation position and bead extraction position; when in
parameter setting mode, it can enter to set parameter, click it again to save the
parameters and return to auto mode.
4. OK_B key: When in manual mode, it can control the B bead-out motor to switch
between bead-out position, preparation position and bead extraction position; when in
parameter setting mode, it can enter to set parameter, click it again to save the
parameters and return to auto mode.
5. ↓ _A key: In automatic mode or manual mode, it is for manual bead A feeding; in
non-working mode, it is for bead-out motor test, and click again to stop the test; in
parameter setting mode, for modify the parameter value.
6. ↓ _B key: In automatic mode or manual mode, it is for manual bead B feeding; in

第 186 页 共 218 页
non-working mode, it is for bead-out motor test, and click again to stop the test; in
parameter setting mode, for modify the parameter value.
7. ↑ _A key: When in automatic mode (not in the process of embroidery ) or manual
mode, it can stop bead A feeding; when in non-working mode, it can reset the bead A
motor to zero; when in parameter setting mode, it can modify the parameter value.
8. ↑ _B key: When in automatic mode ( not in the process of embroidery ) or manual
mode , it can stop Bead B feeding; when it is in non-working mode , it can reset the
bead output motor of Bead B; when it is in parameter setting mode, can modify
parameter value.
9. SET key: When in non-working mode , it can display the current device type.
The 2nd, 3rd, and 4th digital tube display. If it is left double beads device, it will
display as " d-L "; if it is right double beads device, it will display as " d-r ".
Debugging instructions :
When using the device for the first time, it is necessary to adjust the zero position of
the bead-out motor. Loosen the load side of the bead-out motor, and then reset the
bead-out motor through the keypad until the motor is zeroing successful, then push
the load side to the ready position and fix. This position is motor zero position. Or
after motor zeroing successfully, switch to manual mode, click OK button to make the
motor in bead extraction position, and push load to the end ( leave about 2mm gap to
the final end) and fix it.
Parameter Description:
Four digital 8-segment digital tube is used as the display module.
The 1st digital tube displays " P " , it indicates that it is in the parameter setting mode
at this time.
The 2nd digital tube displays " A " or " B " , indicating that the current setting is the
parameter of Bead A or Bead B.
The 3rd digital tube displays the beads clamping force, the bigger the value, the greater
the strength.
The 4th digital tube displays the bead-feeding speed, the bigger the value, the faster
the speed.
第 187 页 共 218 页
Press SET button: switch Bead A or Bead B parameters; and Press "↑" or "↓" button to
modify the corresponding parameter data. After modification is completed, click OK
button to save the data and exit; or directly click MODE button to return to the
automatic mode when the modified parameter value is valid but will not be saved.

11.6 Operating Instructions for Simple chenille device

Power on the machine with simple chenille devices before operation. Find
“Interface configuration” from “Super User”, then find “ Whether there is simple
chenille function”, turn the option from No to Yes, and click to confirm, as
shown in Fig. 11-12 below.

Fig. 11-12 Interface configuration

The interface pops up "Settings will take effect after HMI restarts". Confirm with
, and wait for the screen to exit interface, then restart, as shown in Fig. 11-13.

第 188 页 共 218 页
 Fig. 11-13 Restart interface

Set the parameters of simple chenille embroidery in Machine Parameter, as shown in

Fig. 11-14 .

Fig. 11-14 Simple chenille configuration in machine parameter interface

Para Name Function Description

Simple chenille lift delay Delay and waiting time after simple chenille device
lifting operation. This parameter is depending on factory
air pressure and adjustment of valve on device; if device
lifts faster, parameter value can reduce; if lifting slowly,

第 189 页 共 218 页
 then change the parameter bigger.
Simple chenille needle Each head can install max. 5 simple chenille presser feet,
position 1 and choose any one to realize the simple chenille
embroidery function.
Simple chenille needle Each head can install max. 5 simple chenille presser feet,
position 2 and choose any one to realize the simple chenille
embroidery function.
Simple chenille needle Each head can install max. 5 simple chenille presser feet,
position 3 and choose any one to realize the simple chenille
embroidery function.
Simple chenille needle Each head can install max. 5 simple chenille presser feet,
position 4 and choose any one to realize the simple chenille
embroidery function.
Simple chenille needle Each head can install max. 5 simple chenille presser feet,
position 5 and choose any one to realize the simple chenille
embroidery function.
Max. Speed of Simple Maximum speed of simple chenille embroidery
chenille
Operating Instructions :
1. Key MODE: used to switch working modes.
When the digital tube displays " A ": Automatic (auto) mode, green light on, device
works when embroidery in the automatic mode.
When the digital tube displays " H ": Manual (hand) mode, green light flashing, this
mode is used for manual debugging of device action.
When the digital tube displays " _ ": device doesn’t work, green light off.
2. Up/down key: When in manual mode , it can control the device to rise and fall
3. OK key: When in manual mode , it can control the motor to swing left and right
4. ↑ key: When in the non-working mode , the motor can be reset

第 190 页 共 218 页
11.7 Operation Instructions for Tracing Cording Device

Fig. 11-15 Tracing cording work parameter setting interface

The parameter setting of tracing cording device, as shown in Fig. 11-10 above .

Para Name Function Description

Tracing cording needle positions Options: first needle / last needle / none

Tracing cording speed Track cording rotation speed

Material-short detection Enable Turn on the function, machine will automatically

detect the cording embroidery, if there is no
material detected, it will automatically alarm.

11.7 Operating Instructions for Laser Cutting Device

Power on the machine with laser cutting device before operation. Find “Interface
configuration” from “Super User”, then find “ Whether there is laser cutting function”,
turn the option from No to Yes, and click to confirm, as shown in Fig. 11-16
below.

第 191 页 共 218 页
 Fig. 11-16 Laser cutting configuration machine parameter interface

The interface pops up "Settings will take effect after HMI restarts". Confirm with
, and wait for the screen to exit interface, then restart, as shown in Fig. 11-17.

Fig. 11-17 Restart interface

第 192 页 共 218 页
Set the laser cutting parameters in Machine Parameter interface.

Para Name Function Description

Laser workable area ( X- ) Maximum value of the laser head working range at the
negative direction of the X axis.

Laser workable area Maximum value of the laser head working range at the
( X+ ) positive direction of the X axis.

Laser workable area ( Y- ) Maximum value of the laser head working range at the
negative direction of the Y axis.

Laser workable area Maximum value of the laser head working range at the
( Y+ ) positive direction of the Y axis.

Laser head offset X The amount of deviation between the laser device and
flat emb.head during laser cutting. Set a certain value of
laser cutting offset on the X axis, to make the laser cut
more accurately in the specified area.

第 193 页 共 218 页
Laser head offset Y The amount of deviation between the laser device and
flat emb.head during laser cutting. Set a certain value of
laser cutting offset on the Y axis, to make the laser cut
more accurately in the specified area.

Min. cutting speed Minimum speed of laser cutting.

Laser airblow off delay During the laser cutting process, the blowing nozzles that
are turned on after the cutting need to delay the time of
closing before stopping working.

Laser airblow on delay During the laser cutting process, the blowing nozzles that
are turned on after the cutting need to delay the time of
open before stopping working.

Laser on delay (light out During laser cutting, the delay time is required when the
delay) laser light starts to emit.

Laser off delay (light off During the laser cutting process, the delay time is
delay) required when the laser is turned off when the cutting is
completed.

Chapter 12 _ Operation instructions for chenille embroidery

12.1 Parameter setting of chenille embroidery
Set the machine parameters of chenille embroidery from super user interface,
according to the machine configuration, set the number of chenille heads and the
number of needles on each chenille head. As shown in Fig. 12-1 below.

第 194 页 共 218 页
 Fig. 12-1 Chenille machine parameter setting

Fig. 12-2 Chenille machine parameter setting

Para Name Function Description

Nos of chenille heads Quantity of chenille heads, which has been configured
before EXW factory.

第 195 页 共 218 页
Nos of needles per Quantity of chenille needles on each head, which has been
chenille head configured before EXW factory.

Chenille Spindle Parking Mixed chenille embroidery machine main shaft angle at
Angle normal stopping.

Chenille spindle zero Correction to the chenille spindle error, to make sure the
compensation spindle zeros and stops more accurately.

Chenille M-axis parking The angle value after zeroing completed, this is a fixed
angle value and cannot be modified, otherwise there is error.

Chenille M-axis zero Correction to the chenille M-axis error, to make sure the
compensation M-axis zeros and stops more accurately.

Chenille Looping Shaft Correction to the chenille looping shaft error, to make
Zero Compensation sure the looping shaft zeros and stops more accurately.

Chenille workable area Maximum value of the chenille head workable range at
( X- ) the negative direction of X axis.

Chenille workable area Maximum value of the chenille head workable range at
( X+ ) the positive direction of X axis.

Chenille workable area Maximum value of the chenille head workable range at
( Y- ) the negative direction of Y axis.

Chenille workable area Maximum value of the chenille head workable range at
( Y+ ) the positive direction of Y axis.

Chenille head offset X Distance between the two types heads at X direction,
normally based on flat emb. head.

Chenille head offset Y Distance between the two types heads at Y direction,

第 196 页 共 218 页
 normally based on flat emb. head.

Chenille color-changing Two modes chenille color-changing: automatic start and

mode manual start. Automatic start means that the machine
automatically moves to the next needle position after
detecting one needle position finishes working. In manual
mode, the machine does not automatically change colors
and waits for manual pulling the lever to proceed to the
next step.

Max. speed of chenille The maximum rotation speed of the chenille spindle
spindle during normal operation.

12.2 Instructions for the first start-up of chenille embroidery

Power on the machine with mixed chenille embroidery function before operation.
Find “Interface configuration” from “Super User”, then find “ Whether there is
chenille embroidery function”, turn the option from No to Yes, and click to
confirm, as shown in Fig. 12-3 below.

Fig. 12-3 Interface configuration interface

The interface pops up "Settings will take effect after HMI restarts". Confirm with

第 197 页 共 218 页
 , and wait for the screen to exit interface, then restart, as shown in Fig. 12-4.

Fig. 12-4 Restart interface

As shown in Fig. 12-5 below, the updated functions about mixed chenille embroidery
will be displayed in the Auxiliary Function interface, click Chenille Debug, enter
chenille debugging interface as shown in Fig. 12-6.

Fig. 12-5 Chenille debugging interface

第 198 页 共 218 页
 Fig. 12-6 Enter the chenille debugging interface

Click “Lift Motor Control”, and pop-up shown in Fig. 12-7.

Fig. 12-7 Lift Motor Control Pop-up

第 199 页 共 218 页
 Fig. 12-8 Gear Setting Pop-up

The user can change the potentiometer value through the gear position, and the motor
drives the needle bar to rise and fall to judge the height.

If switch the motor gear to 10 , click and the motor drives the needle bar to lift

to the 10th gear position, and the potentiometer value will also change to the value
corresponding to the 10th gear. If the gear value is 10 for the current gear, click
to cancel the changes. As shown in Fig. 12-8 .

Click “Thread-tighten/loosen Control”, and pop-up shown in Fig. 12-9.

第 200 页 共 218 页
 Fig. 12-9 Thread-tighten/loosen Control Pop-up

Click color-change position, chain-stitch position, thread-trim position, and chenille

position to switch the current position of thread-tighten/loosen control.

When choose color-change bit button , click , thread-tighten/loosen

control motor turns to the color-change position and the potentiometer value will
display color-changing position value. The current position of the
thread-tighten/loosen will also display the color change position.
Click “Chenille Color Change Debug”, and its pop-up as shown in Fig. 12-10.

第 201 页 共 218 页
 Fig. 12-10 Chenille color change debugging pop-up

Choose the needle bar to switch the color, and the current needle bar will display
the needle bar number.

12.3 Working parameters of Chenille embroidery

According to the machine configuration, set the commonly-used working
parameters of chenille embroidery in Super User, as shown in Fig. 12-11 below .

Fig. 12-11 Chenille working parameter setting

第 202 页 共 218 页
Para. Name Function Description

Chenille spindle working speed Spindle motor running speed during chenille
embroidery

Chenille working acceleration Acceleration at chenille spindle working

Chenille start slow motion stitches Slow motion stitches when chenille embroidery
starts stitching

Chenille spindle start slow speed Chenille spindle starting slow motion speed
during chenille embroidery spindle working.

Chenille moving frame max. speed The maximum speed limit during frame moving
limit on chenille embroidering.

Chenille looping rotation angle Looping shaft rotating angle during working.

Starting angle of Chenille There are 12 parameters from 100rpm to

looping( 100rpm-1200rpm ) 1200rpm, representing under each speed,
machine starts looping action when the spindle
angle is at the set value.

Chenille trimmer off-thread Enable After thread-trim, the thread will be off.

Chenille trimming Enable Automatic thread trimming

Chenille working height gear The height of needle bar during chenille
stitching.

Chain-stitch working height gear The height of needle bar during chain-stitch
embroidering.

第 203 页 共 218 页
No thread-trim for same color at During switching between chenille and
chenille and chain-stitch chain-stitch, if it is the same color, and the frame
changing distance is less than 12mm, the thread
will not be trimmed ( in order to improve
production efficiency )

Chenille looping start deviation The deviation angle of looping shaft relative to
angle the correct position during chenille
embroidering.

Chain-stitch loop start deviation The deviation angle of looping shaft relative to
angle the correct position during chain-stitch
embroidering.

Chenille start locking stitches Nos of locking stitches during chenille

embroidery starting.

Chenille ending stitches Nos of locking stitches during chenille

embroidery finishing.

Parking Loop-shaft zeroing Whether the loop shaft automatically return to

zero when parking.

Chenille thread-break detect. Turn on this function and set the chenille
disable thread-break non-detection.

Chenille thread-break detect During chenille embroidery work, Nos of

start-jump stitches. skipped stitches when detecting bobbin thread
breakage.

Chenille dusting There are options: no dust removal / dusting as

per work hours / dusting as per work-stitches /

第 204 页 共 218 页
 keep dusting

Dusting stitches interval Set the dusting removal data as per working
stitches, when the machine reaches the set
stitches value, it will dust automatically.

Dusting hours interval Set the dusting removal data as per working
hours, when the machine reaches the set time
value, it will dust automatically.

Dusting duration The duration of each dust removal

12.4 Color-changing board parameters for chenille embroidery

To modify the parameters of chenille debugging, set the parameters of the chenille
headboard in the super user, as shown in Fig. 12-12 below .

Fig. 12-12 Chenille color change board parameter interface

Para Name Function Description

第 205 页 共 218 页
Color-change position Click color-change position, the motor drives the
potentiometer to rotate. When the motor rotates to the
color-change position, the potentiometer value is just
parameter set value. (This is reference value, do not
modify)

Thread trim position Click thread-trim position, the motor drives the
potentiometer to rotate. When the motor rotates to the
thread-trim position, the potentiometer value is just
parameter set value. (This is reference value, do not
modify)

Chain-stitch position Click chain-stitch position, the motor drives the

potentiometer to rotate. When the motor rotates to the
chain-stitch position, the potentiometer value is just
parameter set value. (This is reference value, do not
modify)

Chenille position Click chenille position, the motor drives the

potentiometer to rotate. When the motor rotates to the
chenille position, the potentiometer value is just
parameter set value. (This is reference value, do not
modify)

Thread-tighten/loosen motor Starting speed of the thread-tighten/loosen motor

start speed

Thread-tighten/loosen motor Running speed of the thread-tighten/loosen motor

running speed

Thread-tighten/loosen motor The acceleration of thread-tighten/loosen motor during

start-stop acceleration starting and stopping

第 206 页 共 218 页
Error range of Error range of the thread-tighten/loosen motor
thread-tighten/loosen motor

Zero braking duration The time of braking for the motor to reach the zero
position

Chenille Needle Bar qty. Number of chenille needle bars

Color change brake time The time required for the color change motor to brake

Thread-tighten/loosen motor The ratio between the degree of deceleration of motor

braking range ratio braking and its max. speed.

12.5 Parameters of headboard for chenille embroidery

Fig. 12-13 below is the description of chenille embroidery headboard parameters

Fig. 12-13 Chenille machine head board parameter setting

第 207 页 共 218 页
Para. Name Function Description

ADC error range The error range when ADC collects potentiometer value

Gear 1-11ADC value The value of the potentiometer when the gear reaches
1-11, this data is reference value, No modification.

Lift-motor starting speed Speed when the lift-motor starts

Lift-motor running speed Speed during the lift-motor working

Lift-motor start-stop Acceleration when the lift-motor starts and stops

acceleration

Lift-motor braking Braking acceleration of the lift-motor

acceleration

Scissor-motor starting Speed when the scissors-motor starts

speed

Scissor-motor running Speed during the scissors-motor working

speed

Scissor-motor start and Acceleration when the scissors-motor starts and stops
stop acceleration

Scissor-motor brake Braking acceleration of the scissors-motor

acceleration

Scissors motor The movement displacement of the scissors motor when

displacement it is working

Chenille thread clip open The thread clip open displacement during chenille
displacement embroidery; the scissors take the thread to the clip after
thread-cutting, and when stitches start, the scissors

第 208 页 共 218 页
 move forward and push open the thread-clip, to make it
loosen.

Thread-break detection Waiting time during thread-breakage detection

duration

Nos of chenille heads The number of Chenille heads on each embroidery

machine

Chapter 13 _ Operation instructions for coiling embroidery

13.1 Instructions for the first start-up of coiling embroidery
Power on the machine with mixed coiling embroidery function before operation.
Find “Interface configuration” from “Super User”, then find “ Whether there is coiling
emb. function”, turn the option from No to Yes, and click to confirm, as
shown in Fig. 13-1 below.

Fig. 13-1 Interface configuration interface

第 209 页 共 218 页
The interface pops up "Settings will take effect after HMI restarts". Confirm with
, and wait for the screen to exit interface, then restart, as shown in Fig. 13-2.

Fig. 13-2 Restart interface

As shown in Fig. 13-3 below, the updated functions about mixed coiling embroidery
will be displayed in the Auxiliary Function interface, including Coiling M-axis angle,
Coiling bobbin-thread detection and Coiling upper-thread detection,

Fig. 13-3 Mixed Coiling embroidery interface

第 210 页 共 218 页
Click “Coiling M axis angle” to set M-axis rotate angle as shown in pop-up Fig. 13-4.

Fig. 13-4 Pop-up of M-axis rotation angle

Set the M axis angle, the input value range is 0~360 degrees. Click spindle angle
0°, 90°, 180°, 270° in the middle column to control the M-axis rotation angle, turn to
the corresponding angle position, and confirm with to execute the operation .

Press and hold to rotate clockwise, and hold to rotate

counterclockwise. When click , Pop-up will close and M axis will not move.
(Note: When pressing the rotation button, Set the rotation speed in Machine
Parameters from Auxiliary Function)
Click “Coiling Bobbin thread detection”, and pop-up will be shown as in Fig. 13-5.

第 211 页 共 218 页
 Fig. 13-5 Coiling Bobbin thread detection dialog box

Click to start detection, and the light on the machine head will flash red,

turn the bobbin thread wheel, and the light will turn green. is for detection
pausing.

Click “Coiling upper thread detection”, and pop-up will be shown as in Fig. 13-6.

Fig. 13-6 Elastic Line Control Dialog Box

第 212 页 共 218 页
 Click to start detection, and the light on the machine head will flash

red, turn the bobbin thread wheel, and the light will turn green. is for
detection pausing.

13.2 Coiling parameter settings

According to the machine configuration, set the machine parameters of coiling
embroidery from Super User interface, and there are Coiling headlock type, Coiling
jump-stitch frame-changing stitches, etc. As shown in Fig. 13-7 below.

Fig. 13-7 Parameter setting of mixed coiling embroidery

Para Name Function Description

Coiling headlock type Electromagnetic Headlocking or Motor Headlocking.

Coiling jump-stitch Mixed coiling embroidery jump-stitch frame-changing

frame-changing stitches stitches, if inputting 0 stitches, it means no jump. If the
number of consecutive jumping stitches is bigger than the
set value, then there will jump-stitch frame-changing.
When jumping stitches change the frame by stitches
number, the stitches jump distance is bigger than the set

第 213 页 共 218 页
 value, jump-stitches will shift the frame.

Coiling spindle parking Mixed coiling embroidery machine main shaft angle at
angle normal stopping.

Coiling spindle zero Correction to the coiling spindle error, to make sure the
compensation spindle zeros and stops more accurately.

Coiling workable area Maximum value of the coiling head workable range at the
( X- ) negative direction of X axis.

Coiling workable area Maximum value of the coiling head workable range at the
( X+ ) positive direction of X axis.

Coiling workable area Maximum value of the coiling head workable range at the
( Y- ) negative direction of Y axis.

Coiling workable area Maximum value of the coiling head workable range at the
( Y+ ) positive direction of Y axis.

Coiling head offset X Distance between the two types heads at X direction,
normally based on flat emb. head.

Coiling head offset Y Distance between the two types heads at Y direction,
normally based on flat emb. head.

Coiling color-changing Two modes coiling color-changing: automatic start and

start mode manual start. Automatic start means that the machine
automatically moves to the next needle position after
detecting one needle position finishes working. In manual
mode, the machine does not automatically change colors
and waits for manual pulling the lever to proceed to the
next step.

第 214 页 共 218 页
Max. speed of coiling The maximum rotation speed of the coiling spindle during
spindle normal operation.

13.3 Working parameters of coiling embroidery

According to the machine configuration, set the commonly-used working
parameters of coiling embroidery in Super User, as shown in Fig. 13-8 below .

Fig. 13-8 Working parameter setting of coiling embroidery

Para. Name Function Description

Coiling Spindle working Spindle motor running speed during mixed coiling
speed embroidery work

Coiling stitch-jump max. The maximum spindle speed during mixed coiling
spindle speed embroidery with stitches jumping.

Coiling M-axis bar-pull to M- axis of coiling machine returns to zero position

stop and zero. when pulling the bar to stop.

第 215 页 共 218 页
Coiling M-axis thread-break M-axis of coiling machine returns to zero position
to stop and zero when thread-breakage to stop.

Coiling M-axis normal stop Coiling M -axis normal stop and return to zero
and zero position

Coiling M-axis rotation Angle when mixed coiling machine M-axis keeps
duration angle rotating.

Coiling M- axis rotation start Angle when the mixed coiling machine M-axis starts
angle rotating.

Coiling thread-trim method Options: no trim / bobbin-trim / bobbin-and-upper

trim

Coiling thread-break detect.. Coiling embroidery thread-breakage will not be

Disable detected when turning on this function.

Coiling upper thread-break Nos of stitches during upper thread-breakage detected

detected stitches in coiling embroidery, Set a value of thread-breakage
stitches, it will be judged as thread-breakage if it
reaches the value.

Coiling bobbin thread-break Nos of stitches during bobbin thread-breakage

detected stitches detected in coiling embroidery, Set a value of
thread-breakage stitches, it will be judged as
thread-breakage if it reaches the value.

Coiling upper thread-break Skipped stitches in upper thread-breakage detection

detect. skipped stitches during coiling embroidery work.

Coiling bobbin thread-break Skipped stitches in bobbin thread-breakage detection

detect. skipped stitches during coiling embroidery work.

第 216 页 共 218 页
Pleated upper thread-break Nos of stitches during upper thread-breakage detected
detect.stitches in pleated embroidery, Set a value of thread-breakage
stitches, it will be judged as thread-breakage if it
reaches the value.

Pleated bobbin thread-break Nos of stitches during bobbin thread-breakage

detect.stitches detected in pleated embroidery, Set a value of
thread-breakage stitches, it will be judged as
thread-breakage if it reaches the value.

Pleated emb. locking stitches Nos of stitches for pleat embroidery stitch-locking

Pleating distance Pleat spacing during pleating embroidery

Coiling mode max. speed The fastest rotation speed in coiling embroidery mode

Zigzag emb. swing starting The starting position of zigzag swing in zigzag
position embroidery

Zigzag Mode 2 Frame Zigzag Mode 2 Frame Compensation

Compensation

Coiling tracing motor zeroing Turn on this function, the coiling head tracing motor
in starting will automatically return to zero position when
starting.

第 217 页 共 218 页
13.4 Description of Coiling headboard parameters

Find the coiling embroidery headboard parameters in the super user

Para Name Function Description

Headlock type Options: No Locking / Electromagnet lock /

stepper motor lock

Headlock running angle Running angle of the headlock motor when it

is working

Headlock start speed Speed when headlocking starts.

Headlock running speed Speed when headlocking work.

Headlock acceleration Acceleration during head-locking

One way electromagnet PWM Closing time of one-way electromagnet PWM

shutdown time

M-axis rotation start-stop speed M axis rotation start and stop speed

第 218 页 共 218 页
M-axis rotation zeroing speed M- axis rotation zeroing speed

M- axis rotation speed M- axis rotation working speed

M-axis rotation acceleration M- axis rotation working acceleration

M-axis manual movement speed M- axis manual movement speed

Presser foot lift displacement Displacement of presser foot lifts up and

down.

Presser foot start speed Speed of presser foot starts

Presser foot zeroing speed Speed when presser foot returns to zero

Presser foot running speed Presser foot running speed

Presser foot acceleration Presser foot acceleration

Zigzag start speed Zigzag start speed

Zigzag zeroing speed Zigzag return to zero speed

Zigzag running speed Zigzag running speed

Zigzag acceleration Zigzag acceleration

Presser foot down start angle Starting angle of presser foot descending down

Presser foot lift start angle Starting angle of presser foot rising up

Duration angle of presser foot action Duration angle during presser foot movement

Presser foot amplitude Amplitude of presser foot

Zigzag swing start angle Angle of zigzag device starting swing.

第 219 页 共 218 页
Zigzag swing duration angle Duration angle of zigzag device swing

Zigzag swing Zigzag device swing

Zigzag Top Position Top position of Zigzag lifting

Appendix 1 Error Code List

1. Single bead device error code

Error Code Error Description

r F1-F3 light on motor alarm

r F1 lights up Bead-out motor is abnormal

r F2 lights up Material shortage alarm

r F3 lights up Bead-out action Abnormal, may be communication problem

2. Double-bead device error code

Error Code Error Description

r.01 Bead A motor alarm

r.02 Bead A motor zeroing failure

r.03 Bead A lack of material

r.04 Bead A action error

r.10 Bead B motor alarm

r.20 Bead B motor zeroing failed

r.30 Bead B lack of material

r.40 Bead B action error

3. Simple chenille device error code

第 220 页 共 218 页
Error Code Error Description

F1-F3 light on Motor zeroing failed

4. 8-sequin device error code

Error Code Error Description

Er.01 Sequin Color-changing motor zeroing failed

Er.02 Sequin Spec-changing motor zeroing failed

Er.03 Sequin Color-changing motor alarm

Er.04 Sequin Spec-changing motor alarm

Er.05 Sequin Color-changing Failed, Sequin-out motor position Wrong

Er.06 Sequin Color-changing Failed, color change motor is in motion

Er.07 Sequin-out motor movement abnormal, displacement is 0, please check

whether sequin size has been set.

Er.08 Color is changing, sequin-out unable.

Er.09 Sequin-out motor starts abnormally.

Er.10 Sequin-cut motor moves abnormally, displacement is 0, please check the

parameters

Er.11 Sequin-cut motor starts abnormally

5. Error code of the needle position detection board device

Error Code Error Description

E1 The driver alarms, and please check whether there is a machinery stuck

E2 The needle position detection board is abnormal, please check whether the

magnet is installed high or low, or any board is damaged.

E3 Needle zero sensor is out of position

E4 Not near the needle position , the needle-position detection board responds

wrong position.

第 221 页 共 218 页