USER MANUAL

Please read this manual carefully before use

Please keep this manual for future reference ROHS
CONTENTS
1. INTRODUCTION AND SAFETY 1
2. PRESENTATION 3
3. INSTALLATION 6
4. CONTROL PANEL 10
5. USE 11
6. APP USER MANUAL 12
7. MAINTENANCE AND STORAGE 16
8.TROUBLE SHOOTING 17
9. EXPLODED VIEW 19
 1. INTRODUCTION AND SAFETY
1. INTRODUCTION AND SAFETY 1. WARNING-this is a dangerous power tool. Use
care when operating and follow all safety
1.1 Introduction instructions and warnings.
2. Read the owners/operating manual carefully
and follow all safety instructions before operating
Thank you for purchasing our product. the machine.
You will have and enjoy the extra free time while using
our robot lawn mower to mow your lawn. You will be 3. Objects can be thrown from mower while
impressed with your lawn's appearance and best of all, operating, keep a safe distance from the machine
robot makes it for you. when operating, take caution.

The robot mower may be used only by those who know 4. Keep children, pets and bystanders away from
how to operate it after reading and understanding the mower when operating.
instructions in this manual. 5. WARNING-Operate the disabling device before
Model: E1800 working on or lifting the machine.
CE, RoHs approved.
6. Never use a high-pressure washer or even
Product, product specifications and this document are running water to clean the mower.
subject to change without notice. All other trademarks
are property of their respective owners. 7. Sharp rotating blades. Keep hands and feet
away and do not attempt to lift mower from this
area.
8. WARNING-Do not ride on the machine.
IMPORTANT!
The following pages contain important safety and 2. Specifications symbol
operating instructions. Please read and follow all
instructions in this manual. Carefully read and review Taizhouname:
Product Tianchen
RobotIntelligence
lawn mower &Electrics Co,Ltd Product name: Robot lawn mower
Product
Model: name: Robot
E1800 Ip54lawn mower Model: E1800 Ip54
all safety instructions, warnings and cautions contained Model:
Input: XXXXX
29.4 V 4A IPX485W
Input: XXX V --- 2A 85W
Input: 29.4 V 4A
Ouput : 29.4 V 4A
Made in China
in this manual. Made in China
S.N.:XXXXXXXXXXX
Made in China
S.N.:XXXXXXXXXXX

Failure to read and follow these instructions, warnings ROHS

RoHS ROHS
20XX
and cautions statements may result in severe injury or Pasted on mower Pasted on charging station
death to persons and pets or damage to personal
property. It’s not permitted to modify the original design
S.N.: XXXX XX XX XXX
of robot. All modifications are made at your own risk. year month date number
: Waste electrical products should not be disposed
WARNING of as household waste. Please recycle where
facilities exist. Check with your Local Authority or
Robot lawn mower can be dangerous
retailer for recycling advice.
if incorrectly used!

IMPORTANT INFORMATION
Read through the Operators Manual
carefully and understand the content before
using your Robot.

1.2 Symbols on Mower

These symbols can be found in the mower. Study them
carefully so you understand their significance.
1. The symbol is pasted on the top cover,
Please read the means carefully before use
the appliance.
1 2
4 5 6
7 8 9
0

-1-
 1. INTRODUCTION AND SAFETY
4. Charging station symbol. - Inspect and clear the mowing area of all debris (toys,
tree branches, items of clothing, anything with a height
less than 6cm) before operating the mower.
CAUTION! - Never raise the mower or attempt to inspect the
Position this side of the Charging Station blades while the mower is operating.
towards lawn interior.
- Always turn off the power before lifting the mower or
attempting any adjustment.

- When operating the mower in manual mode, maintain

This label is pasted on charging station, please make a safe distance from behind or around the mower and
sure to position this side towards lawn interior. Failure wear proper foot apparel.
to do may result in damage to property or persons.
- Do not operate the mower on slopes greater than 30
degrees or use it in manual operation on slopes where
5. Warning symbol. a firm footing is not possible.

DANGER! Sharp rotating DANGER - Do not operate the mower if any safety feature or
blade. Keep hands and feet device is damaged or inoperable.
away. Serious injury can
- Do not attempt to disable or defeat any safety feature
occur. or device.
- Use heavy gloves when inspecting or servicing the
blades.
1.3 Symbols in the User Manual - Wear eye protection and use gloves when installing
the virtual wire and driving the wire stakes/pegs. Firmly
These symbols can be found in this user manual. drive all pegs in order to keep the wire from becoming
a tripping hazard.

WARNING - Do not use the charging station power supply with an

extension cord.
xxxxxxxxxxxxxxxxxxxxxxxxx. - Use only the original equipment power pack and power
supply/charger with this mower.
A warning box indicates a risk of personal injury exist.
- Do not use the power supply/charger if the cord has
become damaged.

IMPORTANT INFORMATION - Do not place metal objects in the area of the charging
sheets on the charging station.
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx. - Do not place metal objects across the charging heads
of the mower.
An information box indicates a risk of material damage - Do no spray water directly into the docking area of the
exist, especially when the stated instructions are not charging station or onto the control panel on charging
station.
followed. The box is also used where there is a risk of
user error. - The mower has sharp rotating blades! Please care the
mower when it is mowing, in case of serious injury occur.
1.4 Safety instructions - Keep the lawn mower in perfect operating conditions
- Read the owners/operation manual carefully and by performing the maintenance procedures outlined
follow all the safety and warning instructions. by the manufacturer. Good maintenance guarantees
better performance and longer service life.
- This machine has sharp rotation blades! Never allow
the mower to operate unattended; keep bystanders, - In order not to irreversibly damage electric and
children and pets away from mower when in operation. electronic parts, do not wash the robot with water jets
- Never allow anyone to ride or sit on mower. at a high pressure and do not plunge it partially or
thoroughly in water, as it is not watertight.
- Never allow anyone or person who is not familiar with - It is absolutely forbidden to use the robot in explosive
the safe operation of the mower to operate the mower. and flammable environments.
- Keep hands and feet away from the cutting blades - The operator or user is responsible for accidents or
and other moving parts. hazards occurring to other people or their property.
- Never attempt to service or adjust the mower while it - Fill up all small holes and even all small mounds inside
is in operation. working area. It’s to keep the robot with perfect operating.
-2-
 2. PRESENTATION
2. PRESENTATION
This chapter contains information you should be aware of before placing the installation.
2.1 What’s in box
14 15
1
2 6

5 16 17

4
18 19

7
12 13

8
20 21
9
10
11

22

1 Emergency button 14 Charger

Press it to turn on the mower .
Press it to turn off the mower.
15 Virtual wire (100m):
Used to mark mowing area and
2 Control panel create a virtual wall for the mower.
4 Cutting height adjustment knob 16 Virtual wire connectors (10pcs):
5 Charging sheet Used to connect virtual wire.
6 Blade 17 Pegs (100pcs):
7 Home button Used to fix the virtual wire to the
Press it when the mower is on, ground around the lawn perimeter
it goes back to charging station and around obstacles.
automatically. 18 Blades for replacement (3pcs)
8 Charging light
Red: charging 19 Stakes (4pcs):
Green: full charged / idle. Used to fix the charging station to Consumable parts:
the ground. 1. Blades
9 Virtual wire light
2. Virtual wire
Colorless: in good connecting 20 English user manual 3. Virtual wire connectors
Red: Broken wire/ idle 4. Pegs
10 Power terminal 21 Charging head 5. Stakes
11 Virtual wire terminal 22 Cutting height adjustment spanner 6. Rear running wheels
red terminal 7. Front wheels
black terminal 8.Cutting height adjustment
12 Hole for stake
spanner
13 Charging head

-3-
 2. PRESENTATION
2.2 Function of E1800 - Two cutting modes
- Lift sensor There are two cutting modes of the mower, go straight
There are lift sensors located between the top and middle and go circle (high efficiency).
cover. If the mower is lifted from ground, it will stops In Auto, mower selects cutting mode intelligently.
working within 1 second. It goes straight if the grass is sparse or it has be cut off,
and it goes circle if the grass is dense or long.
- Tilt sensor In manual mode, the mower will go where you direct it.
There are tilt sensors installed on the mower too, when
the mower is tilted over 30 degrees in any direction, it
stops working within 2 seconds. - Virtual wire
The robot lawn mower can't be operated without a virtual
- Bump sensor wire. (we suggest to use 100m-600m of virtual wire). The
The whole top cover is movable. Both front and side mower will follow virtual wire to charging station, the virtual
of mower equipped with bump sensors that will wire acts as a virtual fence. It will get on the virtual wire
activate when the mower strikes solid, fixed object when until it meets charging sheets, then it gets off from virtual
that object is at least 6cm in vertical height from the wire and starts cutting inside.
supporting surface of the mower. When the bump sensor
activated, the mower will back up for working. - Mower stops working if virtual wire is cut off or
charging station is power off.
- Rain sensor If virtual wire is cut or broken, or the charging station
There are two rain sensors located on the mower. loose power, the mower will stop working within 3 seconds
The mower will go back to the charging station
automatically when it's raining. - Four steps to safely start the mower
Rain sensors can be selected ON/OFF from APP.
Turn on: the mower will go back home if it is raining. 1. Connect charging station with power supply by charger
Turn off: the mower will go on mowing when it is raining. and make sure the recharging light is in green color.
2. Connect virtual wire to charging station and make sure
- Wifi it is in good connecting(virtual wire light in colorless).
The IOS user can search “EGROBOT” in the Apple 3. Press emergency button and start auto mode.
Store to download the application.
The Android user search “EGROBOT” in the Google
- Overload protect
Play to download the application. The cutting motor and running motor are monitored
continuously during operation for any situation that
- Touch sensor may cause these motors to over-load.
Touch the handle when the mower is cutting, it will In the event this is detected, the mower stops operating.
cease function.
- Waterproof
- Area working time setting(mowing schedule) Waterproof design, which protect inside parts from
Set up one week (From Monday to Sunday, once for humidity.
each day) cutting schedule from APP. This function The waterproof class is I P54.
should be used together with Area location setting.
- Gyroscope
- Cutting width: 21cm The mower has gyroscope to keep it going straight on
inclines.
- Easy cutting height adjustments
. the mower
The cutting height could be adjusted on - Area location setting(Subarea setting)
bottom cover cutting height adjustment knob via the You can select Subareas for the mower to cut. This works
equipped spanner. well for large lawn. See Section 6.4.

- Auto recharge system

- Different languages selection on App.
When the mower senses a low battery situation, it will
shut off the cutting motor and search for the virtual wire.
- Range
Once found it will follow the virtual wire to the charging
station for recharge automatically. Once charging is There are four range options, user can choose the
complete, the mower will back up a few centimeters distance when robot hit virtual wire according the
ready to go again in stand by mode. condition of different lawns.

- Emergency stop switch

There is an emergency button located on the top of
mower and in red color.
Press it to turn on the mower .
Press it again to turn off the mower.

-4-
 2. PRESENTATION

2.3 Technical data

Model No. H750 H750T Battery
Mower technical date Type of battery Lithium
Gross weight 15KGS Battery capacity 2.2Ah 4.4Ah
Net weight 12KGS Charging time ≤1.5hours ≤3hours
Mower size 48*36*21.5cm(LWH) Average working time 60mins 120mins
Rated power 75W Functions:
Noise ≤60db Follow virtual wire walking is optional
Qty for cutting blades 3pcs Mower is disabled without power to charging station
Cutting height 2.5-5.5cm Mower is disabled if virtual wire is cut or broken
Cutting width 18cm Cutting height adjustment
Cutting speed 35m/min Rain sensor
Blades rotate speed 3200rpm Auto recharge
Hill capability 20degree Max slope Intelligent spiraling
Max ambient functioning temp. 40℃ Go straight
Coverage(for once charging) 200m ±20％ 400m ±20％
2 2
Anti theft
800m ±20％
2
Working capacity Lift sensor
Tilt sensor
Note:
How large an area is mow per recharged depends WIFI Application
primarily on the condition of the blade and the type of Bump sensor
grass, growth rate and humidity. The shape of garden
is also significant. If the garden mainly consists of open Waterproof
lawns, mower can mow more area per hour than if the Touch sensor
garden consists of several small lawns separated by
trees, flower beds and passages. Time set-up system
Emergency switch
Charging station and virtual wire Password set-up
Charging station size 44*48.2*15cm(LWH) Gyroscope
Virtual wire maximum length 300m/0.5mm Language option
Standard virtual wire length 100m/0.5mm Subarea setting
Range option

2.4 Working route

-5-
 3. INSTALLATION
3. INSTALLATION 3.3 Charging station installation
This chapter describes how you to install this mower. - Choose best installation place, please make sure
Before starting the installation, read the previous it is flat, no water, no magnetic interference and no
chapter 2. Presentation. obstacle in the front of charging station.
Read the whole of this chapter before starting the
installation. How the installation is made also affects
how well the mower will work. It is therefore important
to plan the installation carefully.
3.1 Preparations
Training
- Read the instructions carefully. Be familiar with the
controls and the proper use of the mower.
- Never allow people unfamiliar with these instructions
or children to use the mower. Local regulations
may restrict the age of the operator.
- The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Charging station best install place:
3.2 Hardware adjustments 1. Make sure it is flat
2. No magnetic interference
Blade adjustment 3. No water and far away from puddle
The mowing system used by this mower is based on 4. No obstacle in front of charging station
an effective and energy efficient principle. Unlike
normal lawn mowers, the mower cuts the grass instead - Please fix the charging station on horizontal place and
of striking it off. correct direction.
Rain sensors on the mower is optional,suggest operate the
mower in dry weather to obtain best possible result.
Even though the mower can mow in rain,wet grass - Lay virtual wire
collects on mower easily and the risk of slipping as picture shows. Peg
on steep slopes increases.

The blades must be in good condition to obtain the best - Fix the charging
mowing result. In order to keep the blade sharp for as station with four
stakes by
long as possible it is important to keep the lawn free hammer.
from branches, small stones and other objects
(especially the objects less than 6cm height). Please fill
up small holes and even out small mounds to make sure
lawn is flat. IMPORTANT INFORMATION
How to adjust the cutting height: Before locate the charging station, please make sure
mower must follow the virtual wire and back to
1. Turn power off station in CLOCKWISE direction.
2. Use height adjustment spanner rotate knob clockwise.
3. Adjust cutting height device manually 2.5cm-5.5cm.
4. Use tool rotate knob anticlockwise. IMPORTANT INFORMATION
Do not tread or walk on the charging station plate.

Cutting height adjustment knob

Cutting height explanation: take 3cm level for example.

Cutting height: 3cm

Grass
Height
3cm
3CM

-6-
 3. INSTALLATION

3.4 Virtual wire installation - Bury virtual wire below grass and fasten it on
the ground with pegs, so that the mower should
The virtual wire can be installed in one of the following not cut the wire.
ways:
- Securing the wire to the ground with pegs. Add pegs in order to pull the
virtual wire virtual wire down to the ground
It is preferable to staple down the virtual wire, if you surface, below the grass tips.
want to make adjustments to the virtual wire during
the first few weeks of operation.
- Bury the wire
It is preferable to bury the virtual wire(max depth: 5cm)
if you want to detach or aerate the lawn.
If necessary both methods can be combined so one IMPORTANT INFORMATION
part of the virtual wire is stapled down and the Hard or dry ground may cause pegs to break when
remainder is buried. driving them in. In extreme cases, watering the lawn
- Install virtual wire with pegs 1 meter apart. It’s where the pegs will be driven.
best to use smooth radius corners than sharp
angles. See pictures.
- A minimum distances between the front of the charging
station and an obstacle is 2 meters. And make sure the
distance from corner to front of charging station is at least
OK 2.5 meters. Make sure to lay a 2.5 meters minimum
straight-light of virtual wire in front of charging station.

- If a high obstacle, for example a house, wall, fence or

other obstacle which is higher than the cutting lawn
borders the working area, the virtual wire should be laid
at least 40cm from the obstacle. This will prevent mower
from colliding with the obstacle.

- If a passage or a ground with same height of cutting lawn,

the virtual wire should be laid at least 10cm from the edge.

- A minimum distance between the pool edge of virtual

wire is 40cm.

- A minimum distance between two corners is 1meter.

>90

Min:40cm

10cm
Max:1cm - A maximum distance of the virtual wire
Passage or Pool to and from the island is 1cm, and fix the
a ground with two wires with one peg.
same level
of the lawn.

- There are two types of set up of the

virtual wire around the charging station.

Min:40CM Put the charging station near corner.

please take location for reference.

House, wall, fence or Please make sure to set a straight-line

other obstacle higher at least of 2.5m in front of charging
than the lawn station. The charging station should be
far away from puddle.
Straight-line
at least:2.5m
Min:40CM
Location
-7-
 3. INSTALLATION
- Use the virtual wire to isolate areas inside the working - Care must be taken not to create a corner sharper
area by creating islands around obstacles that can shorter than 90 degrees when setting up virtual wire.
not withstand a collision, for example, flower beds and A corner sharper less than 90 degrees can cause the
fountains. Run the wire out to the area, route it mower to lose track of virtual wire. We can make
around the area to be isolated and then back along greater than 90 degrees corner like follow picture
the same route. If pegs are used, the wire should be shows.
laid under the same peg on the return route. When
the virtual wire to and from the island with a maximum
distance of 1cm, the mower can drive over the wire.
Correct corner set up,
using several angle to
- If protected obstacles are grouped closely together avoid an angle of less
isolate them individually. Continuous virtual island Incorrect corner than 90°.
if obstacles are close to edge, leave them out of the setup
mowing area.

Greater than
Max: 1cm Max: 1cm 2m

Min: 2m

Max: 1cm

40cm
Proper setup in sharp corners
Virtual wire
Virtual wire

- The distance between charging station and virtual Virtual wire connecting
loop should be 2 meters at least.
- Joining the virtual wire .
If the virtual wire is not long enough
and needs to be spliced: Use supplied
wire connector. It is waterproof and
gives a reliable electrical connection.

To splice: Insert both cable ends in the

connector. Now press down the button on
top of the connector fully. Use a pair of
pliers or the like, as the button on the
connector is difficult to press down by
hand.

1cm
Tree with hole or flowers
Greater around require placing a
than 2m wire around it

- 8-
 3. INSTALLATION
3.5 Charging head installation. 3.7 Power connection.
1. Connect charger terminal b with charging station power
terminal a.
Connect 1 from plug a to 1 from plug b and screw it
it tightly.

- + + -
2 1 1 2

Power terminal Power terminal

on charging station on charger

Please fasten the charging heads on the charging 2. Connect the charger with power supply.
station in clockwise. 3.Charging light on station in green: Non-recharging.
charging light on station in red: recharging.
3.6 Virtual wire and charging station connecting. 3.8 Recharge.
1. When the mower senses a low battery situation, it will
1. Cut the two ends of virtual shut off the cutting motor and search for the virtual wire.
wire to a length of 1cm that’s Once found it will follow the virtual wire to the charging
convenient for reaching station for recharge automatically. Once charging is
the virtual wire terminal on complete, the mower will back up a few centimeters
charging station. and stand by.
Strip the two ends of wire.
2. The mower will go back to the charging station
2. Connect the cut two ends of virtual wire to virtual wire automatically when it's raining.
terminal located on charging station. Rain sensors can be selected ON/OFF from APP.
Pls take care of positive and negative terminal. Turn on: the mower will go back home if it is raining.
Turn off: the mower will go on mowing when it is raining.

IMPORTANT INFORMATION
All the buttons (except the emergency switch and
power button ) are locked which can not be used
during the robot is in recharging.

3. The mower reverses several centimeters and stop

there with entering standby mode after fully
recharged.

3.The virtual wire light turns colorless while virtual wire

connected well with charging station.
A failed connecting between virtual wire and charging
station cause a blinking red light and send out a
beeping from charging station.

WARNING
Redundant virtual wire at back of charging station
must be cut off.

-9-
 4. CONTROL PANEL
4. CONTROL PANEL
4.5Match mower with charging station:
4.1Control Panel view Take mower close to charging station, turn on the emergency
switch,press auto button A and home button
simultaneously, the signal light starts flickering, press the
home button on the charging station, the signal light - turns
bright,press confirm button on the mower panel until the
signal light is off, the matching complete, turn off the
mower and started again.
Note: Mower was matched with charging station before leave
the factory.

A Auto mode

Confirm button(to confirm your selection)

Home button

Power light(lighted when power is on)

Signal light
(lighted when mower detect signal from charging station)

Alarm light(flickering when mower alarms)

4.2AUTO MODE
Turn on the emergency switch, when the signal light flickers
to bright, press auto button A , indicator light start flickering,
press confirm button , indicator light off, mower enter into
the auto mode.

4.3HOME MODE
Turn on the emergency switch, when the signal light flickers
to bright, press home button , indicator light - starts
flickering, press confirm button , indicator light off, mower
enter into home mode.
Note: If the signal light keeps flickering all the time, need to
rematch the address between mower and charging station.

4.4Mower alarming
When the mower stops with alarm, the alarm indicator light
will keeps flickering, cancel alarm by press confirm button ,
alarm indicator light will be off.
Note: If the mower stopped frequently, please check alarm
messages which showed on the APP.

- 10 -
 5. Use
5. USE 5.2 Starting the mower
IMPORTANT INFORMATION There are two locations of start the mower.
1.Take the mower clockwise onto virtual wire, make sure
- Do not leave the mower to operate unattended if you that the mower is not connected with two charging
know that there are pets, children or people in the sheets on charging station. Otherwise, the mower is in
vicinity recharging Mode, it can not be started.
- Mow only in daylight or in good artificial light. 2.Take the robot to start point.
- Avoid operating the mower in wet grass. If set Edge mowing off, the robot begins cutting inside
- Do not operate the mower when barefoot or wearing lawn directly.
open sandals. If set Edge mowing on, the robot will follow the virtual wire
- Always wear substantial footwear and long trousers. cutting for one circle, and back to station first.
- Always be sure of your footing on slopes.
- Use extreme caution when reversing the mower
towards you. To start the robot.
- Always switch on the mower according to instructions
1.Press the Emergency button to turn on the robot.
with feet well away from the blade.
2. Select AUTO A mode, the mower starts working.
Note:If the mower lost contact with station, AUTO or
WARNING
Read the safety instructions before you start HOME mode is not able to start.The signal light
your mower. is always flickering,then need rematch the mower with
charging station,pls refer to 4.5Match mower with charging
station.
WARNING
Keep your hands and feet away from the
rotating blade. Never put your hands or feet 5.3 Stopping mower /Turning off mower
close to or under the body when the motors
are running. 1. Press stop button from APP. Mower
stops and enters standby mode.
2. The mower can be turned off by pressing the
Emergency button directly.
5.1 Preparation

- Ensure the correct installation of the virtual wire.

5.4 Emergency Switch
- Periodically inspect the area where the mower
Press Emergency button at any time the mower power
is to be used and remove all stones, sticks, wires,
off at once. User has to restart it.
bones, and other foreign objects especially the height
of objects is less than 6cm.

- Periodically visually inspect that the blades, blade

bolts and cutter assembly are not worn or damaged.
Replace worn or damaged blades and bolts in sets to
preserve balance.

- Connect the two ends of virtual wire to the terminal

on charging station, and ensure virtual wire is in good
connecting. (Light on charging station is in colorless).
- Insert charger into charging station and secure it with
threaded cap. And then connect charger to power
supply. Ensure the charging station has a good connection
and the light on charging station is Green.
- Periodically inspect the lawn is without any small
hole or mound.

IMPORTANT INFORMATION
User can not start the mower if virtual wire or
charging station is not in good connection.

- 11 -
 6.APP USER MANUAL

The APP is available for IOS and Andriod phone.

Download and Install：
The Android user pls search “EGROBOT” in Google Play to download.
.
The IOS user pls search “EGROBOT” in the Apple Store to download.
For the first time please connect the charging station and virtual wire
and turn on the mower according to the user manual.Then enter the smart
phone setting interface--WI-FI to connect the device.Pls note for first time it takes
about 3-5minutes to connect device, and the device can only connect with one phone
at the same time.
The using of the App:
Click the APP you installed and enter it.

- 12 -
 6.APP USER MANUAL
6.1 Remote control function 3.For the functions like rain sensor,touch sensor,audio alarm
are optional.
Rain sensor:
ON: mower goes back to charging station when it
is raining.
OFF: mower goes on working when it is raining.

After finish setting function,pls press Send to save the

settings.

1.Press ”Auto”, the mower will 6.3 Date&Week&Time settings

work automatically.
2.Press “Remote”, the mower
will work in manual and user
could direct the mower to work
with indication.
Pls note in Remote mode, robot does not recognize the
wire and station.
3. Press “Home”, the robot will go back to station
1.You can synchronize the
automatically.
mower time to cellphone time.
4.Press “Stop” can stop the robot and stand by.
2.After setting new time, pls
Pls note this does not work when mower is charging.
. press Send to save the
5.The blades could be turned on or off by press “MOW” . settings.

6.2 Function settings

6.4 Working Area Setting

1. There are 13 languages

for option: English/French/ 1.This function is to increase
German/Danish/Swedish/ the mowing efficiency for
Finnish/Norwegian/Italian/ large area.It allows to
Spanish/Russian/Polish/ separate a large area into
Dutch/Chinese. maximum 6 small areas.

2.Range function:there are four range options, user can 2.Area location setting
2.1 before entering into this interface, pls separate the
choose the distance when mower hit virtual wire according
garden into several areas as per your own demand.
the condition of different lawns.
Take separate 3areas for example below:

3 4
1 2
- 13 -
 6.APP USER MANUAL
3.Area working-time setting
3.1.The Area working-time setting should be used
together with Area
location setting.
3.2.Choose the mower
working day per week.
3.3Set the start time,
then set the working
time for each area
and Send.
-Pls note if the working
areas are for example
3areas,do not set the
time for other
unselected areas.
-If set Area 1 with 0min,
it means Non-cutting in
Area 1.
-If unselect working in
Area 2,even has set
working time in Area 3,
mower will not work in
-Route the wire around the passage to separate the Area 3.
the area.The virtual wire to and from the edge of 3.4.Edge mowing:
passage is 1meter at least.pls refer to below picture. ON:every time mower
-A minimum distance between the virtual wire which will cross to the back
is to make passage is 50cm. of station to mow the
2.2 choose the areas that you set accordingly: edge grass on virtual
2-1Area 1 is non-optional,selects by default. wire and follow the wire
2-2After select Area, the symbol back to station first.
* will be in red color.
2-3 Start locating to set memory
point.
A memory point is to program the
where to leave virtual wire and 4.Put the mower back to station and wait for working.
go inner lawn.Each area needs
a memory point.
Pls make sure the mower voltage
more than 27V before setting the
memory points,and pls put the
mower at charging station before
locating.

-It is best to set the memory point

in the middle of two corners.
--A better position of memory point is 3meter distance
from the beginning or the end of an area.

- 14 -
 6.APP USER MANUAL

6.5 Password

1.This is for setting the

mower password.
2. and you can set 4-digit
password.
Initial password:1234.
Input old password,then
Input new password and
Send.
3.Password function is optional.

6.6 Mower-state Query

1.You can get the mower

voltage info.
2.Click “Mower-state Query”
to view alarm info.

- 15 -
 6. MAINTENANCE AND STORAGE
6. MAINTENANCE AND STORAGE 15. Servicing of the mower should be according
to manufacturers instructions. This product
- During maintenance operations, use the individual (include battery pack)must be disposed of at a
protections indicated by the Manufacturer , especially designated collection pint for electrical and
when intervening on the blade. electronic waste. For more information, contact
- Before performing maintenance operations, make your local city office or the shop where you
sure that the robot has stopped in safety conditions. purchased the product.
6.2 Robot Storage
PROGRAMMED MAINTENANCE INTERVALS CHART
Packed the mower and all spareparts with the original
Frequency Component Type of operation Reference
package, and storage the carton off the ground in a
Clean and check the See “Robot cool, dry place. Temperature should not be colder
efficiency of the cleaning”
blade than 14F°(-10℃)
Every week Blade
If the blade is bent due See “Blade 6.3 Blade replacement
to an impact or if it is replacement”
worn-out, replace it. Blade replace steps:
1.Stop the robot in safe conditions.
Robot Carry out cleaning See “Robot
Every month
cleaning” 2. Wear protective gloves.
3. Turn the Robot upside down.
Every 3 months Robot Carry out for rechage See “Battery” 4. Unscrew the blade and remove it.
5. Replace a new blade and screw it tightly.

6.1 Robot cleaning

1.Stop the robot in safety conditions.
2. Wear protective gloves.
3.Clean all the outside surfaces of the
robot with a sponge soaked in warm water.
4.Do not use solvents or benzene so not to damage
the varnished surfaces and the plastic components.
5.Do not wash the inside parts
of the robot and do not use water
jets in pressure so not to damage 6.4 Front wheel cleaning
the electric and the electronic When front wheels are not easy to rotate, please turn robot
components. upside down, check it and dismantle the screw cap to take
the front wheel out of robot, dismantle end caps and
remove the residues, like mud, grass etc from end cap,
then reinstall it on the robot.
WARNING
6.5 Battery
Never use a high-pressure washer or The battery is maintenance-free, but has a limited life
even running water to clean the robot. span of 1-3years. Battery life is dependent on the
length of the using season and how many hours per
week the robot is used. A long season or many hours
6.Check the lower part of the robot (cutting blade area of use per week, means that the battery must be
and wheels) and remove the deposits and/or residues replaced more regularly.
that might obstruct the correct functioning of the robot. - Attentions of lithium batteries
7. To remove the deposits and/or other residues from Please charge the lithium batteries in accordance with
the blade, use a suitable brush. standard time and procedures.
8. Clean the outside of the charging station from any When the power is too low. It should be started
accumulated residues. charging as soon as possible.
Storage, we suggest the optimum storage of lithium
9. Keep all nuts, bolts and screws tight to be sure the
battery is with 80% power and keep in the shade.
appliance is in safe working condition.
Don’t connect the anode and cathode of battery.
10. Replace worn or damaged parts for safety. Don’t take apart, repair or modify the battery privately.
11. Ensure that only replacement cutting means of the - Disused battery processing
right type are used. Please contact the nearest waste treatment center
12. Ensure that batteries are charged by using the correct and consultation with recycling and proper disposal
charger recommended by the manufacturer. of views.
13.Incorrect use may result in electric shock, IMPORTANT INFORMATION
overheating or leakage of corrosive liquid from the
battery. Charge the battery fully at the end of the season
14. In the event leakage of electrolyte flush with before winter storage. And recharge it every 3
water/neutralising agent, seek medical help if it comes months.
into contact with the eyes etc.
- 16 -
 7.TROUBLE SHOOTING
7. TROUBLE SHOOTING

Problem Alert info Possible reasons Solutions

Auto mode is not able to 1.The virtual wire fails to 1.Check the virtual wire
send signals. light on charging station.
start,charging station is Virtual wire was cut off. Be sure the virtual wire is
beeping. 2.The virtual wire was connected to the charging
Signal light is off. station well (light in
cut off. colorless).
2. Connect the virtual wire
with wire connectors.

Auto mode is not able to 1. Check the power and

1.main power is shut off. make sure the charger is
start,charging station is Charging station is out of Bad communication connecting well with power
beeping. power. between charging station supply and charging
and mower. station.
Signal light is off.

1. Mower is lifted from 1. Take the mower to level

Mower stops working Lift sensor or pressure sensor ground. ground and restart it.
and beeps. activated. 2. Someone or object ride 2. Take the object away
or sit on the mower. from mower and restart it.

1. Running wheel strike 1. Clean the lawn and make

Current of right running motor sure it is free from hard objects.
hard objects.
is too large,check it.
2. The mower is trapped 2. Clean the lawn where mower
Mower stops working is trapped or restart the mower
in lawn. in another place.
and beeps.
Current of left running motor
is too large,check it.

1. Adjust the cutting height

1. Cutting height is too low. to suitable height.
Mower stops working Current of cutting motor is too 2. Blade strikes hard 2. Clean the lawn and make
and beeps. sure it is free from hard objects.
large,check it. objects.
3. Clean the lawn where mower
3. Mower is trapped in lawn is trapped or restart the mower
in another place.
- 17 -
 7.TROUBLE SHOOTING

Problem Display Possible reasons Solutions

Mower stops working Robot is over tilted. Mower is tilted over than Turn off the mower and take
and beeps. 30 degrees from the the mower to level ground.
ground. Then restart the mower.

The batteries can not 1.Charger is not powered 1. Check whether charger
recharge on. is well connected.

2.Battery lifetime 2. Send the mower to service

decreases. station and replace the
battery.
1. Grass is extremely 1. Cut the grass appropriate
overgrown or very wet, height.
Mower gets stuck,
does not move. 2. Terrain needs 2. Fill in all holes, cover or
landscaping repairs. exclude all exposed roots
in order to smooth the
terrain.

Mower does not complete Obstacle along the path. Watch the full operation of
the edge. follow virtual wire walking
and confirm no obstacle
is present.

Mower does not detect

The ground before the Reset the charging station
the charging station charging station isn’t flat.
contacts. in a flat place.

Mower reaches charging Height difference between Confirm the ground before
station when its contacts the charging station and the charging station is leveled
are above the charging lawn surface at the with the station if necessary
sheets. entrance to charging station. fill area with dirt and level off.

The mower behaves in an Virtual wire incorrectly Relocate the virtual wire.
anomalous around flower placed
beds.

1. Damaged cutting blade. 1. Replace a new blade.

2. Cutting blade flooded by 2. Stop the mower in safety,
residues(tapes, ropes, plastic use protection gloves to
fragments, etc) avoid the risk of cuts on
hands, remove the fold
3.The start of mower occurred cause from blade.
The mower is very noisy. with obstacles being too
closed (less than 1m away) 3. Start the robot in new place.
or in presence of unexpected
obstacles (fallen branches, 4. Get the motor repair or
forgotten objects, etc.) replace by service station.
4. Damaged running motor 5. Increase the cutting height
or cutting motor. or use a normal lawn mower.
5. Grass too high.
- 18 -
 8. EXPLODED VIEW

Robot Exploded View

- 19 -
 8. EXPLODED VIEW

Robot spareparts list:

1:Cutting motor 20:Front wheel

2:Cutting motor base 21: Emergency switch
3:Protective shield 22:wire sensor board
4:Blade shield 23:Main PCB
5:M8 screw nut 24:Rain sensor
6:M4 screw nut 25: Emergency stop
7:Blade 26:Control panel PCB
8:Flat washer 27:Battery cover
9:M4 screw bolt 28:Battery
10:Running motor 29:bolt
11:Rear wheel 30:Eccentric shaft
12:Wheel shell 31:Snap ring-2
13:Bottom case 32:Locking spring for blade adjusting frame
14:Dust proof ring 33:Seal strip
15:Gasket for dust proof ring 34:Top cover
16:Hall PCB-03 35:Recharging sheet
17:Holder for hall PCB
18:Magnet-01
19:Snap ring-1

Charging Station Exploded View

1.Station cover
2.PCB
3.Power terminal
4.Virtual wire terminal
5.Short plate
6.Charging head
7.Charging head permanent seat

- 20 -
Robot lawn mower
USER MANUAL