TOYOTA CAMRY 2005 - SUB WOOFER

Section I - Installation Preparation

Part Number: PT233-33020
Section I - Installation Preparation
Kit Contents General Applicability
Item # Quantity Reqd. Description Note:- LE, SE
1 1 Sub Woofer Assy
2 1 Wire Harness Recommended Sequence of Application
Item # Accessory
1 EC Mirror
Hardware Bag Contents 2 TVIP
Item # Quantity Reqd. Description 3 Sub Woofer
1 7 Wire Ties
*Mandatory
2 1 50mm x 50 mm Butyl Rubber
Pad Legend
3 1 Seat Clip STOP: Damage to the vehicle may occur. Do not
STOP
proceed until process has been complied with.
4 3 3" x 6" Foam Tape
5 1 Operation Manual OPERATOR SAFETY: Use caution to avoid risk of
injury
CRITICAL PROCESS: Proceed with caution to ensure
Additional Items Required For Installation a quality installation. These points will be audited on a
Item # Quantity Reqd. Description completed vehicle installation
1 GENERAL PROCESS: This highlights specific
2 processes to ensure a quality installation. These
points will be audited during the accessory installation
3
TOOLS & EQUIPMENT: This calls out the specific
Conflicts tools and equipment required for this process
Note:- Premium Audio System, Passenger Power Seat
Recommended Tools
Safety Tools
Vehicle Protection Blankets
Hand Protection Gloves

Special Tools
Carpet Cutting Template CAD IADS P/N:
CAM02-027-01
Small Tip Nylon Pry Tool

Installation Tools
Phillips Screwdriver
Socket 10 mm, 14 mm
Ratchet
Extension 6 in.
Nylon Pry Tool
Side Cutter
Torque Wrench 3 lbf-ft, and 27 lbf-ft
Utility Knife K nife

Special Chemicals
Cleaner 3MTM Prep Solvent-70

Issue: C 07/08/04 Page 1 of 6 pages DIO

 TOYOTA CAMRY 2005 - SUB WOOFER
Section II - Installation Procedure
Section II - Installation Procedure

NOTE: For vehicles equipped with side impact

air bags - before disconnecting the SRS connector STEP 2
located under the passenger seat, wait 90 seconds
minimum after battery disconnection.

A. Remove Center Cluster and Radio/Combo

STEP 1
1. Disconnect negative battery cable before any
disassembly starts.
Figure A1
STOP 2. Place all removed parts on protected surface. Nylon Pry Tool

3. Remove AC/Heat control panel (Step 1 in

Figure A1). Pry four clips using nylon pry
tool. Then disconnect wires from AC/Heat
controls. Clip location is depicted by arrows
in Figure A1.
4. Remove AC Duct faceplate (Step 2 in
Figure A1). Disconnect clock wire harness.
Figure B1 Nylon Pry Tool
5. Use 10 mm socket to remove four bolts on
Radio/Combo, disconnect wires and remove
Radio/Combo.

A. Remove the Scuff Plate and Kick Panel

1. Remove scuff plate using nylon pry tool as
indicated by arrows in Figure B1
2. Remove under dash cover by pressing on the
indented areas (3 places) as indicated in
Figure B2 and then pulling in a downward
motion.
Figure B2
3. Remove kick panel using pry tool making sure
to unscrew nut as shown in Figure B3

Figure B3 Nylon Pry Tool

Issue: C 07/08/04 Page 2 of 6 pages DIO

 TOYOTA CAMRY 2005 - SUB WOOFER
Section II - Installation Procedure

B. Remove the Glove Compartment

1. Remove the bolt on lower right side of glove
box. (Figure C1).
2. Remove cap on lower left side of glove box
using the small tip NRT to reveal Phillips
screw and remove. (Figure C1 inset). SCREW

3. Remove 3 Phillips screws from top of glove

box. (Figure C1) and remove glove box. CAP

10mm Hex
C. Prepare Passenger Seat Head

1. Remove the two forward seat bolts using

Figure C1 Ratchet 10 mm Socket
14 mm socket. Tilt seat forward and slide Phillips Screwdriver
forward.
2. Remove rear bolt covers.
3. Remove the 2 rear bolts.
NOTE: Before disconnecting the SRS connector Remove these connectors
located under the passenger seat, if equipped,
ensure 90 seconds has passed since removing
battery negative cable.
STOP 4. Apply vehicle protection to the center console
area and tilt the seat back (be careful not to
scratch vehicle and pull on wire harness),
revealing bottom of seat and disconnect the
connectors depicted in the circled area and Remove and Replace W/H Clip

remove the seat clip depicted by the arrow in

Figure D1. A replacement clip is in the kit. Figure D1

D. Route Wire Harness

1. Starting under the passenger seat, leave 3"-4"
out of the carpet hole.
2. Route wire harness along same path as seat
ATTACH FOAM
harness under the carpet until you get to scuff TAPE HERE

plate. Then route wire harness, using wire tie

to fix bend, under the scuff plate on the
outside of vehicle, use the existing clips to
secure the wire harness along the scuff plate. Figure E1
(Figure E1).
Issue: C 07/08/04 Page 3 of 6 pages DIO
TOYOTA CAMRY 2005 - SUB WOOFER
Section II - Installation Procedure
3. Route wire harness from scuff plate clips up
through the glove compartment to back of
head unit. (See Figure E2) Bundle excess wire harness

4. Route wire harness through center cluster as

shown in Figure E3.
5. Secure the wire harness using one foam tape
and one wire tie as indicated in Figure E1.
6. Secure the wire harness using the six wire ties
as indicated by the circled areas in Figure E2.
7. Bundle any excess wire harness with the wire
tie closest to the radio (Figure E2).
8. Use the T-connection plus 10 pin connector Figure E2
and plug into back of radio. Wrap the loose
connectors with foam tape and wrap the fuse
to the main harness with foam tape.
9. Clip the wire ties.
E. Install Sub Woofer
1. Place carpet cutting template in vehicle. The
template is aligned to the rear seat bolts.
2. Using a razor knife, cut the carpet and foam
padding. Lift the flap of carpet/padding up
that was cut to expose the floor of the vehicle.
3. Clean floor of vehicle and rear bracket bottom Figure E3
with cleaner to remove dust and oils. Peel off
paper coating from one side of butyl rubber 20mm
VEHICLE FRONT

adhesive and attach to rear of sub woofer

Hinged Piece of Carpet
bracket. Remove the other tape cover then
install the sub woofer in vehicle using front
locator pins as guides. (Figure F1) Replace
carpet flap over rear bracket.
4. Lower seat to original position, making sure
the seat locator pins go through the front Butyl Rubber Adhesive
brackets and into the floor holes.
Figure F1
5. Hand start the seat bolts and then torque to
37 N-m (27 lbf-ft)
Issue: C 07/08/04 Page 4 of 6 pages DIO
TOYOTA CAMRY 2005 - SUB WOOFER
Section II - Installation Procedure
F. Reassemble Vehicle
1. When reinstalling the radio, hand start the
bolts before using a wrench.
2. Reinstall all removed panels and parts. Be sure
all panel clips are engaged properly.
3. Re-connect negative battery terminal with
4.1 N-m (3 lbf-ft). of torque.
4. NOTE: The sunroof may not operate
correctly when the battery has been
disconnected. If this is the case the sunroof
needs to be reset do the following:
i. Cut the plastic roof protection wrap (if
present) using a Nylon Removal Tool or a
Plastic squeegee on the right, left, and rear
edges of the sunroof.
ii. Then normalize the sunroof by pushing
and holding the switch to the "TILT UP"
side until the sunroof tilts all the way up
and then tilts down a little automatically
(approx. 10 mm at the rear).
iii. Confirm SLIDE/OPEN and TILT/UP
functions.
iv. When completed, make sure the sunroof is
completely closed.

5. Place Operation Manual into glove box.

Issue: C 07/08/04 Page 5 of 6 pages DIO

TOYOTA CAMRY 2005 - SUB WOOFER
Section III - Functional Verifications

Section III - Functional Verifications

Check: Look For:

Accessory Function Checks
Turn on radio Radio display turns on
Antenna is functioning Reception of AM/FM stations
Sub woofer operation Sub woofer - Listen to sub woofer to make
sure it is functioning properly or by feeling
the sub woofer for vibration

Vehicle Function Checks

Power Sunroof (if equipped) Functioning Sunroof.

Hazard Lights Functioning Hazard Lights
HVAC All HVAC Controls Function
Clock (if equipped) Functioning Clock
Rear Window Deffoger (if equipped) Functioning Rear Window Deffoger
Seat Belt Warning Light Functioning Seatbelt Warning Light. If the
warning light remains "ON", it may indicate
a system malfunction.
Glove Box Light (if equipped) Functioning Glove Box Light

Security, (if equipped) Security lamp illuminates (flashes)

SRS Lamp, (if equipped with passenger side SRS Warning lamp illuminates
air bag) approxinmately 3 seconds then goes off.

Issue: C 07/08/04 Page 6 of 6 pages DIO