0% found this document useful (0 votes)
285 views97 pages

Eco Solvent Printer User Manual

The document provides detailed instructions for operating and setting up a printing system, including panel and button descriptions, menu navigation, calibration tools, and driver installation. It outlines various settings and maintenance procedures necessary for optimal printer performance. Users are advised to restore factory settings in case of exceptions and to consult customer service for any issues.

Uploaded by

quarkmachines
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
285 views97 pages

Eco Solvent Printer User Manual

The document provides detailed instructions for operating and setting up a printing system, including panel and button descriptions, menu navigation, calibration tools, and driver installation. It outlines various settings and maintenance procedures necessary for optimal printer performance. Users are advised to restore factory settings in case of exceptions and to consult customer service for any issues.

Uploaded by

quarkmachines
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 97

AILY GROUP

1: Panel description;
2: Button description;
3: Menu description;
4: Calibration tools onlineinstructions;
5: Mongolia Thai driver installation instructions
6: Basic setup instructions
7: Interface test specification
8:Initial settings
9:3D Machine Installation Instruction

Set the system attribute values need to be familiar with Senyang


system knowledge, please read the instructions carefully.
Setting a special property value needs to be restarted to take effect.
After setting the property value, restore the factory settings if an
exception occurs.
For any objection, please contact customer service.
1:panel description

LCD display

Keyboard
1:panel description

Icon is displayed
online, a fork is not
online
2:Button description
On (UP) key: at the standby interface, the button controls the movement of paper (paper back). Non
standby interface, the button control upward selection. When setting the inking station, control the motor to
move upward

Lower (DOWN) key: at the standby interface, the button controls the movement of paper (feed). Non standby
interface, the button control down selection. When setting the ink station, control the motor to move
downwards

Left (LEFT) key: at the standby interface, the button controls the movement of the car to the left. Non
standby interface, you should press the key to select the left (last item). When setting the car position,
control the car to move to the left.

Right (RIGHT) key: at the standby interface, the button enters the maintenance menu. Non - standby
interface, the key control to the right selection (next item). When setting the car position, control the
car to move to the right.

Exit (EXIT) key: when the standby interface, the button does not operate. The non - standby interface
controls the return of the previous menu (cancel) operation.

Confirm (ENTER) key: at the standby interface, the button enters the main menu. Non - standby interface.
This key functions as OK or hold operations

*****If an exception occurs, restore the factory settings and restart*****


3:Menu description

Menu
Press the up and down key to switch options
Press the confirm key to confirm the options
Press the exit key to return to the previous level

3.1 Setup Menu


3.2 Maintenance
3.3 Dev.Mgr.
3.4 Restore Default
3.5 Delivery set
3.6 Heating mode
3:Menu description
3.1 Setup Menu
Press the up and down key to switch options
Press the confirm key to confirm the options
Press the exit key to return to the previous level
The following are not mentioned and can be
ignored

1) Speed: set print speed


2) Fan Setup
3) Spurt
4) LCD contrast
5) Auto Clean
6) Device Address
7) Warn Paper
8) Station Setup
9) Heat Setup
3:Menu description

3.2 Maintenance Menu


Press the up and down key to switch options
Press the confirm key to confirm the options
Press the exit key to return to the previous level

1)Nozzle Test
2)Clean Nozzle
3)Manual Pump
4)Wipe Nozzle
5) Flush
6) Cap Head
7) Inking
3:Menu description
3.3 Station Setup

Press the up and down key to switch options


Press the confirm key to confirm the options
Press the exit key to return to the previous level
The following are not mentioned and can be
ignored

1) Wiper POS
2) Wiper Hight
3) Car Cap POS
4) Cap Hight
5) Print Spurt POS
6) Station POS
7) Spurt POS
8) Wipe POS
4Calibration tools online instructions
1: after the printer is switched on, check the
4:Calibration tools IP address of the device information,
online instructions
2: set the computer's IP address, as follows;
4Calibration tools online instructions

open 4:Calibration tools online instructions


Printer IP Computer IP Connect
4Calibration tools online instructions
Single head is online
Hidi Align:Add the value of the test line overlap to the current value
4:Calibration tools online instructions
Step align:Enter the measurement size in the input box, mm, for example 406.4mm, click “Calculate” and “save”
Tune: enter the corresponding value of the test line overlap in the input box, click “Calculate” and “save”
Print Setup: Click “Save” to save the properties and set the width when the color bar is set to On.

V114ST XP600 Dual NET CV910H FV8332A UV860 DEV;0866-0000


4Calibration tools online instructions

4:Calibration tools online instructions

This interface is the advanced settings


interface
Voltage regulation: waveform voltage
regulation (450~580)
Voltage type:select Print waveform
Color: according to the color of the test bar,
the order of ink arrangement
Rint: choose print empty
Dual seq: according to the color of the test
bar,the order of ink arrangement
Make sure to save attributes
Cancel: go back to the next level
4Calibration tools online instructions

4:Calibration tools online instructions


This interface is an advanced calibration
color calibration interface
This setting is the calibration of nozzle
width
Click one-way to the left (right) and fill in
the corresponding input box, depending
on the value of the overlap of the
chromatic lines
The double head needs to select one of
the nozzles
5:蒙泰驱动安装说明
Mongolia Thai driver installation instructions
1. installed Meng Thai software, inserted into the Meng Thai softdog, open MengThai
software
2. click on the file - click the printer to set Y...
5:蒙泰驱动安装说明
Mongolia Thai driver installation instructions
3:安装蒙泰打印机---》自定义打印机---》选择蒙泰驱动---》设置为默认打印机;
3: install Meng Thai printer - - Custom printer - select "Meng Thai drive" - set as
default printer
5:蒙泰驱动安装说明
Mongolia Thai driver installation instructions
4:制图(文件--》新建文件--》设置文件的属性---》载入图片 。如图);
4: Drawing (file -- new file -- properties of settings file] loads pictures. As shown in fig;
5:蒙泰驱动安装说明
Mongolia Thai driver installation instructions
5:打印:(文件--》打印--》打印机设定---》选择打印精度 ---》打印。如图); 5:
Print: [file] print - - printer settings - select Print precision - - print. As shown infig.;
6:Basic setup instructions
This interface is the starting point for printing
Press the left and right keys to move the car
Press the up and down key to add and
subtract the current position
Press confirm to save the grating position of
the current car as the starting point of
printing
Press exit and exit the start setting
Note: press the up and down key to change
the value, you need to press the left key to
move to the appropriate location to enter into
force

20
6:Basic setup instructions

This interface is the printing speed setting


interface
Press the up and down key to switch options
Press the confirm key to confirm the options
Press the exit key to return to the previous
level

21
6:Basic setup instructions

This interface is the LCD contrast setting


interface
Press the up and down key to switch options
Press the confirm key to confirm the options
Press the exit key to return to the previous
level

22
6:Basic setup instructions

The interface for automatic maintenance


settings interface
Press the up and down key to switch options
Press the confirm key to confirm the options
Press the exit key to return to the previous
level

23
6:Basic setup instructions

This interface sets the interface for the paper


switch
Press the up and down key to switch options
Press the confirm key to confirm the options
Press the exit key to return to the previous
level
Note: do not open the function without
installing the paper detector

24
6:Basic setup instructions

This interface sets the interface for the ink


station origin
Press the left and right keys to move the car
Press the confirmation key to save the current
position as the origin of the ink station
Press the exit key to return to the previous
level

25
6:Basic setup instructions

This interface is used to maintain the flash


jet position selection interface
Press the up and down key to switch
options
Press the confirm key to confirm the options
Press the exit key to return to the previous
level

26
6:Basic setup instructions

This interface is the wiper position setting


interface
Press the left and right keys to move the car
Press the confirm key to save the current
position for the wiper position
Press the exit key to return to the previous
level
* * * scraping mouth position for the car
moving, scraping the mouth when the stop
position

30
6:Basic setup instructions
This interface is the wiper setting interface
Press the up and down key to move the
wiper blade
Press the left and right keys to move the car
Press the confirm key to save the current
position for the wiper position
Press the exit key to return to the previous
level
The location of the wiper blade is the
position of the scraper before and after the
wiper is moved
Wiper location is only valid for motor
scrapers

31
6:Basic setup instructions
This interface is the wiper height setting interface
Press the up and down key to move the wiper
blade
Press the left and right keys to move the car
Press the confirm key to save the current position
as wiper height
Press the exit key to return to the previous level
* * * wiper blade height is the upper and lower
position of the wiper blade when the dolly is
moving
The wiper blade height is only valid for the wiper
blade that can move up and down the ink station

32
6:Basic setupinstructionS
This interface is the head height setting
interface
Press the up and down keys to move up
and down the ink station

Press the left and right keys to move the car


Press the confirmation key to set
Press the exit key to return to the previous
level

34
6:Basic setupinstructionS
This interface is to set the head height interface
Press the up and down key to switch options
Press the confirm key to confirm the options
Height of the head: the height of the ink station
at the head

Save the origin of the ink station: the position of


the car at the head
Note: the head height is only valid for the lifting
type ink station, and the head position of the
inking station is the origin position of the ink
station

35
6:Basic setup instructions

This interface is for printing flash jet position setting


interface

Press the up and down key to modify the flash frequency


Press the left and right keys to move the car
Press the confirm key to save the current flash position
and flash frequency
Press the exit key to return to the previous level
Print flash spray flash spray position refers to the position
in the process of printing, print in some blocks of solid
color pictures, in order to prevent a part of nozzle hole for
a long time without the use of broken ink, printing can be
opened in the flash spray, spray flash numerical
frequency refers to the number of pass flash of a jet

36
6:Basic setup instructions

This interface is heating setting interface


Press the up and down key to switch
settings
Press the confirmation key to save the
current settings
Press the exit key to return to the previous
level

37
6:Basic setup instructions

This interface is device information interface


Press the exit key to return to the previous level
1H: single head
B180: grating type 180
S: waveform type
300: has been registered SW:
software version number
SN: hardware version number
196.12.0.25: printer IP
CarPara:a5383904: parameter number

38
6:Basic setup instructions

This interface is to restore the factory


settings interface
Press the up and down key to switch options
Press the confirm key to confirm the options
Select Yes and verify that you need to enter
the password 16753
Press the exit key to return to the previous
level

39
6:Basic setup instructions

Press the up and down key to change the


time
Press the confirmation key to confirm the
time
Press the exit key to return to the previous
level
The setting time of the paper is from the
length of the paper every time the paper is
removed

40
6:Basic setup instructions

This interface is the print interface


Press the confirmation button to stop
printing
Press the exit key to set step two way
000000: total print square
000.0: square number of prints this time

41
6:Basic setup instructions

The interface is set up in the printing step


two way interface
Press the up and down key to change steps
Press the left and right keys to change both
directions
Press the exit key to return to the previous
level

42
6:Basic setup instructions

This interface is for printing pause interface


Press the exit key to cancel the print
Press the OK button to continue printing
Press left to remove the car
Press right to enter the print maintenance
menu

43
6:Basic setup instructions

This interface is for printing to cancel the


interface
Press the up and down key to change steps
Press the left and right keys to change both
directions
Press the exit key to return to the previous
level

44
6:Basic setup instructions

This interface is the maintenance menu


interface in print
Press the up and down key to switch options
Press the confirmation key to confirm the
options and perform corresponding actions
Press the exit key to return to the previous
level

45
7:Interface test specification

* * after the car starts to move, hold (on, right,


exit) key at the same time, enter the test
menu * *
This interface is a machine aging interface
Press left and right key to switch options
Press the confirmation key to confirm the test
Note: click on the confirmation will be
displayed as * * *. Sometimes wait for about
3 minutes the car began to exercise, to
determine whether the correct print width
before aging

46
7:Interface test specification

This interface is flash jet test interface


Press left and right key to switch options
Press the up and down key to switch the
test items
Press the confirmation key to confirm the
test
Under normal circumstances, press the OK
nozzle will flash spray

47
7:Interface test specification

This interface is the SDRM test interface


Press left and right key to switch up and
down items
Press the up and down key to switch the
test items
Verify the SDRM by displaying 3 * numbers
If there is a problem with the trolley panel, it
will display fall
?

48
7:Interface test specification

The interface is grating test interface


Press left and right key to switch options
Press the up and down key to switch the test
items
Confirm to get the current raster value,
move the car 1cm away from the direction of
the ink stack, and press again to confirm
that if the value is not changed, the grating
is not read. If the value becomes smaller,
the grating AB is connected and reversed,
and if the value becomes larger, it is normal

49
7:Interface test specification

This interface is ink pump 1 test interface


Press left and right key to switch options
Press the up and down key to switch the test
items
Press the confirmation key to confirm the
test
Press OK to make ink pump 1 work, and
display to OFF, again press confirm, ink
pump 1 stop work, display to ON

50
7:Interface test specification

This interface is ink pump 2 test interface


Press left and right key to switch options
Press the up and down key to switch the test
items
Press the confirmation key to confirm the
test
Press OK to make ink pump 2 work, and
display to OFF, again press confirm, ink
pump 2 stop work, display to ON

60
7:Interface test specification

This interface is air suction test interface


Press left and right key to switch options
Press the up and down key to switch the
test items
Press the confirmation key to confirm the
test
Press the confirmation to make the air
suction work, and press again to confirm
that the air suction can be stopped

61
7:Interface test specification

This interface is a paper test interface


Press left and right key to switch options
Press the up and down key to switch the
test items
Press the confirmation key to confirm the
test
Press the confirmation material to move
forward, display to stop, again press
confirm to stop paper, show restore

62
7:Interface test specification

This interface is a paper test interface


Press left and right key to switch options
Press the up and down key to switch the test
items
Press the confirmation key to confirm the
test
Press the confirmation material to move
back, display to stop, again press confirm to
stop paper, show restore

63
7:Interface test specification

This interface is a lifting ink stack test


interface
Press left and right key to switch options
Press the up and down key to switch the test
items
Press the confirmation key to confirm the
test
Press the confirmation that the ink stack
should move up, display to stop, and press
again to confirm that the ink stack stops
moving and displays the restore

64
7:Interface test specification

This interface is a wiper sensor test


interface
Press left and right key to switch options
Press the up and down key to switch the
test items
Press the confirmation key to confirm the
test
The normal connection sensor is not
detected and is displayed as OFF, and is
displayed as ON at the time of detection

70
8:Initial property setting instructions

** * before booting, hold down (up, down, left,


right) key, and then switch on, enter the initial
settings menu * *

This interface is the ink stack type setting interface


Press left and right key to switch options
Press the up and down key to change properties
Press the confirm key to save the current selected
property
Lifting type: lifting type ink stack
Type CAP: crash ink stack

71
8:Initial property setting instructions

This interface is the wiper type setting interface


Press left and right key to switch options
Press the up and down key to change properties
Press the confirm key to save the current selected
property
Pop up, fixed: electromagnetic valve type wiper, can
not rise and fall with the ink stack
Up and down: electromagnetic valve type wiper,
follow the ink stack lifting
Motor, fixed: stepper motor type wiper blade, can not
move up and down with the ink stack
Motor lifting: stepper motor type wiper, follow the ink
stack lifting

72
8:Initial property setting instructions

This interface is the print width setting


interface
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the confirm key to save the current
display print width
Note: setting this value is about 10CM larger
than the actual platform width

73
8:Initial property setting instructions

This interface is raster type setting interface


Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
A:150 grating B:180 grating
Other types are invalid
Note: This set should not be changed at will

74
8:Initial property setting instructions

The interface for the car type of motor


settings interface
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
DC: DC motor
Servo: servo motor
BLDC: brushless motor

75
8:Initial property setting instructions

This interface sets the interface for the type of


paper motor
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Step by step: stepper motor
Servo: servo motor

76
8:Initial property setting instructions

The interface for the paper motor steering


settings interface
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property

80
8:Initial property setting instructions

The interface for the car motor steering


settings interface
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Note: this setting item is invalid

81
8:Initial property setting instructions

This interface is the speed setting interface


of paper motor
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property

82
8:Initial property setting instructions

This interface is the LCD type settings


interface
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
AB two items for each other rotation 180
degrees LCD display mode

83
8:Initial property setting instructions

This interface is automatic cleaning type


settings interface
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Flash spray: flash ink action in standby
mode
Cleaning: automatic cleaning action in
standby mode

84
8:Initial property setting instructions

This interface is for entering the cleaning


settings interface
Press left and right key to switch options
Press the (down) button to enter the
cleaning settings menu

85
8:Initial property setting instructions

This interface is the first stage of ink


pumping time setting
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

86
8:Initial property setting instructions

This interface is the first stage of inking off


time setting
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

87
8:Initial property setting instructions

This interface is the first stage of inking


settings
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

88
8:Initial property setting instructions

This interface for the second stage ink set


time settings
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

90
8:Initial property setting instructions

This interface for the second stage ink set


time settings
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

91
8:Initial property setting instructions

This interface for the second stage ink set


Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

92
8:Initial property setting instructions

This interface maintains the head time after


pumping ink
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

93
8:Initial property setting instructions

This interface is the setting interface of


flash spraying times
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

94
8:Initial property setting instructions

This interface is the flash frequency setting


interface
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the previous
layer
This setting item is invalid

95
8:Initial property setting instructions

This interface is the opening time settings of


the ink
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the previous
layer

96
8:Initial property setting instructions

This interface is the time setting for pumping


ink off
Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the previous
layer

97
8:Initial property setting instructions

The interface for the number of ink set


Press left and right key to switch options
Press the up and down key to change
properties
Press the confirm key to save the current
selected property
Press the return key to return to the
previous layer

98
9: 3D Machine Installation Instruction

99
9: 3D Machine Installation Instruction

100
9: 3D Machine Installation Instruction

101
9: 3D Machine Installation Instruction

102
9: 3D Machine Installation Instruction

103
9: 3D Machine Installation Instruction

104
9: 3D Machine Installation Instruction

105
9: 3D Machine Installation Instruction

106
9: 3D Machine Installation Instruction

107
9: 3D Machine Installation Instruction

108
9: 3D Machine Installation Instruction

109
9: 3D Machine Installation Instruction

110
9: 3D Machine Installation Instruction

111
9: 3D Machine Installation Instruction

112
9: 3D Machine Installation Instruction

113
9: 3D Machine Installation Instruction

114
9: 3D Machine Installation Instruction

115
9: 3D Machine Installation Instruction

116
9: 3D Machine Installation Instruction

117
9: 3D Machine Installation Instruction

118
9: 3D Machine Installation Instruction

119
9: 3D Machine Installation Instruction

120
9: 3D Machine Installation Instruction

121

You might also like