Easy7 VMS UserManual
Uploaded by
alftechsolusiEasy7 VMS UserManual
Uploaded by
alftechsolusiUser Manual
Easy7 VMS User Manual
User Manual
Statement
This manual may contain inaccuracies, discrepancies in the operation of product
functions, or typographical errors.
Our company will update this manual according to the reinforcement and change of
product functions, also regularly improve and update the software and hardware
products described in this manual. The updated information will be reflected in the
latest version of the manual without further notice.
Due to our continuous adoption of new technologies, product parameters are
subject to change without prior notice.
This manual is only for the customer's reference and guidance, and does not
guarantee that it is completely consistent with the real object. Please take the real
object as the standard.
All text, tables, and image information in this manual are protected by relevant
national laws and cannot be used without permission.
Please be aware of the open characteristics of the Internet. If you connect your
product to the Internet, there may be risks such as network attack, hacker attack
and virus infection. Our company will not be responsible for the problems such as
abnormal product operation and information leakage caused by this, but we will
provide you with technical support related to the product in a timely manner.
When using this product, please strictly comply with applicable laws and
regulations to avoid infringing on third-party rights, including but not limited to
User Manual
intellectual property, data rights, or other privacy rights. You are also not allowed to
use this product for weapons of mass destruction, biological and chemical weapons,
nuclear explosions, or any unsafe use of nuclear energy or for human rights
violations.
If the content of this document conflicts with applicable laws, the legal provisions
shall prevail.
The copyright and final interpretation right of this document belong to our
company.
User Manual
Preface
This user manual is based on video surveillance system. Provide a brief function
description for the system to help users understand the operation process of the
system.
The purpose of this document is to ensure that the user uses the product properly
to avoid danger or property damage. Before using this product, please read it carefully
and keep it for future reference. If you have any questions in use, please consult our
after-sales service.
Symbolic agreement
For symbols that appear in the document, the description is as follows:
Icon Instruction
Indicates a potential risk that, if ignored, may result in a function that cannot
Notice：
be used properly or an unpredictable result.
The expression is the additional information of the text, which is the emphasis
Explain：
and supplement to the text.
User Manual
Content
1 Product overview ....................................................................................................................................... 1
1.1 Product profile ................................................................................................................................1
1.2 Product highlights .......................................................................................................................... 1
1.3 Update instructions ........................................................................................................................2
1.4 Terms and abbreviations ............................................................................................................... 2
1.5 Precautions for use .........................................................................................................................3
2 Login and Configuration ............................................................................................................................5
2.1 Software login .................................................................................................................................5
2.2 Homepage framework introduction ............................................................................................. 7
2.2.1 Real-time alarm ...................................................................................................................9
2.2.2 P2P Account Login ............................................................................................................ 10
2.2.3 Other button operations .................................................................................................. 11
3 Equipment management ........................................................................................................................ 15
3.1 Encode device ...............................................................................................................................15
3.1.1 Auto search ........................................................................................................................ 16
3.1.2 Add ..................................................................................................................................... 21
3.1.3 Modify ................................................................................................................................ 23
3.1.4 Delete ................................................................................................................................. 24
3.1.5 Invert Selection ................................................................................................................. 24
3.1.6 Refresh ............................................................................................................................... 25
3.2 Decoding device ........................................................................................................................... 25
User Manual
3.3 Gate Equipment ............................................................................................................................25
3.4 Group ............................................................................................................................................. 27
3.4.1 Add device to custom groups ...........................................................................................30
3.4.2 Modify the channel name .................................................................................................31
3.4.3 Get and modify the device alarm port ............................................................................ 32
3.4.4 Modify group ..................................................................................................................... 33
3.4.5 Delete group ...................................................................................................................... 33
4 Live view ................................................................................................................................................... 35
4.1 Custom Device List ....................................................................................................................... 35
4.1.1 Customize the device list with the right-click menu ...................................................... 35
4.1.2 Device grouping right-click menu ....................................................................................36
4.1.3 Device channel right-click menu ..................................................................................... 37
4.1.4 Alarm entry port right-click menu ................................................................................... 39
4.1.5 Alarm output port right-button menu .............................................................................39
4.2 Video preview window .................................................................................................................40
4.2.1 Video preview window displays the information ...........................................................41
4.2.2 Video preview window toolbar ........................................................................................ 43
4.2.3 Video preview screen toolbar .......................................................................................... 46
4.2.4 Video preview window right-click menu .........................................................................48
4.3 Cruise Plan .................................................................................................................................... 50
4.3.1 Modify the cruise intervals ............................................................................................... 52
4.3.2 Delete view ........................................................................................................................ 52
User Manual
4.3.3 Move view .......................................................................................................................... 52
4.4 Group switch set ........................................................................................................................... 53
4.4.1 Modify number of components ....................................................................................... 54
4.4.2 Open/close group switch ..................................................................................................54
4.5 Target information ........................................................................................................................55
4.6 Favorites ........................................................................................................................................ 55
4.7 View ............................................................................................................................................... 56
4.8 PTZ Control ................................................................................................................................... 56
4.9 Unlocks the encrypted channel function ................................................................................... 58
4.10 Fish eye unfold ............................................................................................................................59
4.11 USB keyboard control ................................................................................................................ 60
5 Video playback ......................................................................................................................................... 62
5.1 Video query ................................................................................................................................... 62
5.2 Video playback ..............................................................................................................................65
5.3 Playback control ...........................................................................................................................65
5.3.1 Replay window right-click menu ..................................................................................... 67
5.4 Video download ............................................................................................................................68
5.4.1 Download by file ............................................................................................................... 68
5.4.2 Download by time period .................................................................................................70
5.5 Recently browse ........................................................................................................................... 70
5.6 Fish eye unfold ..............................................................................................................................70
6 System configuration ...............................................................................................................................71
User Manual
6.1 Common Settings .........................................................................................................................71
6.2 Video Settings ............................................................................................................................... 73
6.3 Storage management ...................................................................................................................75
6.4 Intelligent application ..................................................................................................................76
6.5 Record plan ................................................................................................................................... 77
7 Alarm management ................................................................................................................................. 79
7.1 Real-time alarm ............................................................................................................................ 79
7.2 History alarm ................................................................................................................................ 80
8 TV Wall .......................................................................................................................................................82
8.1 Create layout .................................................................................................................................82
8.2 Bind decoding ...............................................................................................................................83
8.3 Scene generation ..........................................................................................................................86
8.4 Preview & Wall up ......................................................................................................................... 88
8.4.1 Demo Mode ....................................................................................................................... 89
9 Vehicle management ............................................................................................................................... 91
9.1 Region creation .............................................................................................................................93
9.1.1 Basic Information ..............................................................................................................93
9.1.2 Entrance/Exit Settings ...................................................................................................... 95
9.1.3 On duty management .......................................................................................................96
9.1.4 Black and White List ..........................................................................................................98
9.2 Region binding ............................................................................................................................100
9.3 Area Preview ............................................................................................................................... 102
User Manual
10 Access Control ......................................................................................................................................106
10.1 Basic Configuration .................................................................................................................. 107
10.1.1 Device Binding .............................................................................................................. 108
10.1.2 Holiday Settings ............................................................................................................ 114
10.1.3 Time Template .............................................................................................................. 115
10.2 Personnel Management ...........................................................................................................119
10.2.1 Permission Group Establishment ................................................................................ 119
10.2.2 Personnel binding .........................................................................................................120
10.3 Access Control Permissions .....................................................................................................122
10.3.1 Controller Configuration .............................................................................................. 122
10.3.2 Permission Configuration ............................................................................................ 130
10.3.3 Interlock Settings ..........................................................................................................132
10.4 Access Control Preview ............................................................................................................133
10.4.1 Access Control Preview Interface ................................................................................ 133
10.4.2 Personnel positioning .................................................................................................. 135
10.4.3 Record Center ................................................................................................................135
11 Face recognition ...................................................................................................................................137
11.1 Face database management ................................................................................................... 137
11.1.1 Face database addition/modification/delete .............................................................137
11.1.2 Face Image Addition ..................................................................................................... 138
11.1.3 Personnel query ............................................................................................................139
11.1.4 Add Existing Face Image ............................................................................................... 139
User Manual
11.1.5 Delete (All) Face Image(s) ............................................................................................. 140
11.1.6 Face Image Import/Export/Export All ..........................................................................140
11.2 Face database download ......................................................................................................... 141
11.2.1 Face library synchronization ........................................................................................142
11.3 Face configuration ....................................................................................................................143
12 Access Management ............................................................................................................................ 145
12.1 Gate Management .................................................................................................................... 145
12.2 Live View ....................................................................................................................................145
12.2.1 Equipment sequencing ................................................................................................ 146
12.3 History of the Gate ....................................................................................................................147
12.3.1 Access to areas .............................................................................................................. 148
12.4 Checkpoint preview ................................................................................................................. 148
12.4.1 Device sorting ................................................................................................................149
12.5 Checkpoint history ................................................................................................................... 150
12.5.1 Access area .................................................................................................................... 150
13 Electronic Map ......................................................................................................................................152
13.1 Electronic Map configuration .................................................................................................. 152
13.1.1 Add map .........................................................................................................................152
13.1.2 Delete map .................................................................................................................... 152
13.1.3 Modify map ....................................................................................................................153
13.1.4 Add / delete devices ......................................................................................................153
13.2 Configure heat zone ................................................................................................................. 154
User Manual
13.3 Electronic map preview ........................................................................................................... 155
14 User management ............................................................................................................................... 157
14.1 Add user .................................................................................................................................... 157
14.2 Edit user .................................................................................................................................... 159
14.3 Delete user ................................................................................................................................ 160
15 Intelligent search ................................................................................................................................. 161
15.1 Face retrieval .............................................................................................................................161
15.2 Behavior analysis and retrieval ............................................................................................... 163
16 Data statistics ....................................................................................................................................... 166
16.1 Face statistics ............................................................................................................................166
16.1.1 Statistics by age group ................................................................................................. 167
16.1.2 Statistics by gender .......................................................................................................168
16.1.3 Statistics by the number of people ..............................................................................170
16.1.4 Statistics by whether wearing glasses .........................................................................172
16.1.5 Statistics by whether wearing mask ............................................................................174
16.1.6 Statistics by body temperature measurement ...........................................................175
16.2 Visitor flow statistics .................................................................................................................177
16.2.1 Real-time Statistics Device List .................................................................................... 178
16.2.2 Real-time Statistics Area List ........................................................................................181
16.2.3 Real-time Data of Real-time Statistics ......................................................................... 183
16.2.4 Video Page of Real-time Statistics ............................................................................... 184
16.2.5 Report statistics ............................................................................................................ 184
User Manual
16.3 Heat map statistics ................................................................................................................... 186
17 Alarm configuration ............................................................................................................................. 189
17.1 Alarm configuration of Monitoring point ................................................................................189
17.1.1 Linkage notification ...................................................................................................... 191
17.1.2 Linking video ................................................................................................................. 193
17.1.3 Linkage alarm output ................................................................................................... 194
17.1.4 Linkage deployment time ............................................................................................ 195
17.2 Alarm configuration of device ................................................................................................. 197
17.3 Alarm configuration of People counting area ........................................................................ 198
18 Operation logs ......................................................................................................................................199
19 Video player ..........................................................................................................................................201
User Manual
1 Product overview
1.1 Product profile
Video monitoring system is a dedicated application for managing, previewing and
operating network monitoring devices based on MacOS and Windows operating
systems, which is applicable to a full range of NVR, IPC and other devices. The software
can realize grouping management of monitoring points according to different scenes,
customize grouping names, conduct real-time video browsing, audio preview, voice
intercom and other operations based on equipment, control equipment PTZ, set preset
bits and calls, switch video playback between custom groups, support front-end and
local video playback, and control playback through the timeline. At the same time,
video files can be downloaded to the client. The software has rich video surveillance
business functions and is suitable for various video surveillance scenarios.
1.2 Product highlights
Comprehensive function
It provides abundant management and operation functions for small and
medium-sized monitoring systems, such as Live view control of audio and video,
retrieval and playback of historical video data, reception of alarm information, linkage
disposal, etc.
Strong extensibility
Video monitoring software capable of integrated management of NVR/IPC.
1
User Manual
1.3 Update instructions
See the update instructions at the time of software release for details.
1.4 Terms and abbreviations
No.
2
User Manual
1.5 Precautions for use
Current monthly largest quantity of human face pictures received from single
channel is 1 million. The current upper limit of quantity of human face pictures received
from all channels is 5 million. If the quantity exceeds the upper limit, result of
intelligent retrieval cannot be acquired.
Standalone version can support 500 point locations at most at present.
Present screen supporting 3,840*2,160 (4K) resolution at most.
This platform is not compatible with cameras in sky-eye series cameras at
present.
MAC AIO only supports external microphones.
As for the equipment added in P2P account number way, audio sampling
frequency shall be set to be 8kHz. Other sampling frequency may cause program failure
on standalone version, so please use it cautiously.
As for the same NVR and IPC, video playback and video download exist at the
same time. 5 channels at most are supported at present. Otherwise, download failure
or equipment overload will be reminder in download process and video playback will
fail.
MAC system authorizes standalone version, such as microphone authority.
Restart the standalone version.
As for MAC version, the Live view in full screen cannot quit from full screen by
pressing ESC (unless equipment list is closed).
3
User Manual
Firewall of computer may influence some normal functions of standalone
version. Please add white list or close firewall.
4
User Manual
2 Login and Configuration
During network access, in order to protect the security and privacy of personal
accounts and improve the security of monitoring, please set the login password and
prevent others from logging in the device to obtain monitoring data.
2.1 Software login
Premise：
The VMS software is installed.
Operation steps:
1. Double-click the application icon on the desktop to enter the system login interface.
You need to set the initial password for the first login, as shown in the following figure.
2. After the initial password is set, enter the password protection setting interface, and
you can choose to skip, as shown in the following figure.
5
User Manual
3. After setting the password protection question or skipping, you can enter the login
interface, as shown in the following figure.
Notice：
In order to protect your personal privacy and corporate data and avoid network security
problems, it is recommended that you set a strong password that meets the security specifications.
In order to improve the security of product network use, the password should be two or more
combinations of numbers, letters and special characters, and support 6-32 bits.
If you do not set the security problem, when you forget the password, you can only uninstall
and reinstall the software.
The interface parameters are described as follows:
Parameter Instruction
6
User Manual
Tick and enable the check box. If the user name and password is correct,
there ’ s no need to input user name and password anymore the next
Auto login time, you may enter automatically.
Cancel automatic login: System configuration -> Common
Settings->Login Settings->Automatic Login Software.
Tick and enable the check box. If the user name and password is correct,
Save password the current password will be saved and it will automatically fill in the
password for the next time.
Click and enable it. If the user name and password is correct, you may
Login
log in the program.
Click enable and click to enter the password verification page. After the
Forget the password password security question is successfully verified, you can re-enter the
initial password setting page to set the password.
English Support shifting between multiple languages.
Click and enable it. Click to close login interface.
2.2 Homepage framework introduction
Introduce the home page interface parameters and function modules.
Operation steps:
1. Enter the correct user name and password in the platform registration and login
interface, and click [Login] to enter the main program interface of the platform. The
default grouping of the Home page is shown in the following figure.
7
User Manual
The functional parameters of the module are described as follows:
Module name Instruction
Live view View the live images at the monitoring point.
Equipment management Add, modify and delete groups.
Video playback Search and play the recording file at the monitoring point.
TV Wall Configuration and preview of TV wall.
Vehicle management Support regional rehicle management
Real-time indication of unit alarm message to facilitate access to
Alarm management
unit exception.
System configuration Typical operation on client configuration.
Manage client users in a unified way, and add, edit, delete and
User management
configure permissions.
Alarm configuration Coordinated configuration of various alarms
Intelligent search Retrieve the received intelligent analysis information, such as face
8
User Manual
retrieval.
Electronic Map Management and operation function of electronic map.
The total amount, proportion and trend of data are displayed
Data statistics
through statistical charts and lists.
Face recognition Management and distribution of face database.
Access Management Bayonet preview and information query
Query the operation log of the system to understand the usage of
Operation logs
the system.
Video player Local video files can be played.
Access control equipment management, personnel and permission
Access Control
addition, real-time monitoring of access control.
2.2.1 Real-time alarm
Premise：
The device has been added to the client software, and relevant alarms, such as
intelligent alarm and mobile alarm, are configured on the device. When an alarm
occurs on the device, the real-time alarm will push the alarm information.
Operation steps：
1. Click the " " button in the upper right corner of the interface to display the real-time
alarm information, as shown in the following figure.
9
User Manual
2. Click " " to enter the alarm setting function module interface. For details, please
refer to Chapter 8 Alarm Setting.
2.2.2 P2P Account Login
Premise：
You have registered an account in the APP.
Operation steps：
1. After entering the interface, click the " " button in the upper right
corner, and the [P2P account login] interface will pop up, as shown in the following
figure.
2. Enter the P2P account and password to log in to the P2P account. Some regions
support mobile phone number or email account registration, please choose according to
the actual situation.
3. After successful login, automatically synchronize the device information under the
P2P account to the cloud device. Operations such as adding, deleting and sharing
devices on the APP will be synchronized and prompted.
10
User Manual
Notice：
The P2P account synchronization device does not support modification and deletion operations
on the client.
2.2.3 Other button operations
Operation steps：
1. Click the " " button in the upper right corner to display the current login status, as
shown in the following figure.
2. Click the " " button in the upper right corner to display the user manual and
version information. Select [User Manual] or [Version Information] to jump to the
corresponding file.
3. Click the " " button in the upper right corner to display the version information and
date.If a new version needs to be upgraded and updated, the icon will change to " ".
Click the icon to pop up an interface to prompt the new version.After clicking "Software
Update", the update interface will pop up, as shown in the figure below. Follow the
11
User Manual
prompts to upgrade to the new version.
4. When the mouse slides over the " " button in the upper right corner of the interface,
the current CPU occupancy and memory occupancy will be displayed, as shown in the
following figure.
5. Click the " " button in the upper right corner of the interface to lock the screen.
After entering the correct unlock password (i.e. login password), the screen will be
unlocked, as shown in the following figure.
12
User Manual
6. Click the " " logout button in the upper right corner of the interface to pop up a
logout prompt box; click [OK] to exit the current platform and return to the login
interface; click [Cancel] or " " in the upper right corner of the prompt box to exit the
current prompt box, as shown in the following figure.
7. Click the " "button in the upper right corner of the interface to minimize the
program; click the" / / "button in the upper right corner of the interface to
restore/maximize/full-screen program; click the " " button in the upper right corner of
the interface to exit the program.
8. To ensure that the user closes the program by mistake during use, when clicking the
" " button to exit the program, a prompt box will pop up to confirm whether to exit
the program, as shown in the following figure.
13
User Manual
9. If " " is clicked by mistake, click "Cancel" to return to previous operation interface;
if you are sure to quit the system, click "OK" to quit.
Explain：
Only accounts with [System Lock Permission] and [System Unlock Permission] can be locked
and unlocked.
The current system time is displayed in the upper right corner of the interface.
The navigation menu bar at the top of the interface can be separated from the main interface by
dragging the menu, and can also be exchanged by dragging.
Interface function items are divided into common functions and basic functions. The module
icons in the basic function area and the common function area can be dragged to each other, and
the user can select the common function for use.
14
User Manual
3 Equipment management
Add, delete, modify and group devices.
3.1 Encode device
Operation steps:
In the Equipment Management interface, click Coding Equipment to enter the
Coding Equipment interface, as shown in the following figure.
Parameters related to the interface are described as follows:
Parameter Instruction
Automatically search for devices under the same network segment,
Auto Search
batch addition supported.
Manually add encode device, support IP method, Standard domain
Add name method, EasyDDNS method , P2P direct connection method,
P2P account number method to add device.
Modify Modify information of already added device.
Delete Delete already added device, batch deletion of device supported.
15
User Manual
Select the device, and output the device information in three forms
Output of Equipment List, Organization Chart, and Organization
Relationship Table.
Click the device, and input the information in Equipment List,
Import Organization Chart, and Organization Relationship Table, which are
contained in the file.
Invert Selection Select all device that are not selected at that moment.
Refresh Update the status of device at current interface.
Name Display the name of all already added device.
Device Type Display the device type of all already added device.
IP Address Display the IP address of all already added device.
Port Display the port of all already added device.
Display the maximum number of video channels allowed to play of
Video Channel
all already added device.
Display the current connection status of all already added device.
Connection Status
The reason will be displayed, if equipment login fails.
Operation Click and enable it to open the web user-side interface of the device.
3.1.1 Auto search
Operation steps:
1. Click the [Auto Search] button to automatically search all devices in the same
network segment and pop up the [Add Device] window, as shown in the following
16
User Manual
figure.The connection mode can be filtered to display devices with different connection
modes, including All, IP and Onvif.
2. Fill in the starting and ending IP in the [device network segment]. You can set the IP
range of the search device. When filling in the IP segment, it supports automatic
completion and verification. After filling, click [Search], and the devices that can be
searched in the IP range of the filled network segment will appear in the search results
below, as shown in the following figure.
17
User Manual
3. Check one or more devices in the device box in the list, and then click the [Add]
button to pop up the [Add Device] window, as shown in the following figure. If you do
not enter a name, the device IP is used as the device name.
4. You can modify the connection mode of the device, including TCP, MCAST (SRTP),
and MCAST (RTSP). Some devices do not support multicast. When MCAST (SRTP) and
18
User Manual
MCAST (RTSP) modes are selected, a prompt will pop up and video preview cannot be
performed.
5. If [Add Offline] is checked, the device that is not online or has an incorrect user name
and password will also prompt successful addition, and the device that failed to be
added will be displayed in the device list; if [Add Offline] is not checked, the number of
devices that were added successfully or unsuccessfully will be prompted, and the
device list will not display the device that failed to be added.
6. Select Import to Group to automatically import the device into the group. Otherwise,
you need to manually add it to the group.
7. If an unactivated device is added, check [Automatic Activation] to activate the device.
After activation, the device IP and the computer IP are in the same network segment. If
the computer has multiple network cards, you need to select them.
19
User Manual
8. You can modify the IP of the discovered device. Select the device to be modified in
the device list, and click [Modify] to pop up the [Modify Device IP] window. Enter the
new IP address and the correct user name and password, and the modification will be
successful and the [Prompt] window will pop up, as shown in the following figure.
9. Click the [Refresh] button to refresh the information of all devices in the search
results list.
Explain：
Device search results are displayed in order of IP.
When MCAST (SRTP) and MCAST (RTSP) modes are selected, different multicast addresses shall
be configured for different devices and different code streams of the same device, otherwise
cross-screen phenomenon will occur.
When adding devices in batches, it is recommended to set a unified user name and password
for multiple devices. If the user name and password information are wrong, it will lead to the failure
of adding some devices.
20
User Manual
3.1.2 Add
Operation steps:
1. Click the [Add] button to enter the [Device Add] interface, as shown in the following
figure.
The interface parameters are described as follows:
Parameter Instruction
Select different add type: IP type, Standard domain name type,
Add mode
EasyDDNS type ,P2P direct connection type and onvif type.
Check to add online or offline devices. Only online devices can be
Off-line Add
added after the check is removed.
Device Name Enter a device name. (There is an illegal character limit when
21
User Manual
adding a device name. The following characters are not allowed to
be entered ~! # $% ^ () = [] { }, ":; '< >? * ` +/\ &)
Device Type This is required when the standard domain name mode is selected.
Device IP Device IP. This field is required when IP and Onvif are selected.
Device ID number. This item is required to be filled in when
Device ID
selecting P2P direct connection mode.
Domain name of device. This is required when selecting the
DNS
standard domain name and EasyDDNS mode.
The communication port of the device. Onvif defaults to 80. IP and
Port
standard domain name defaults to 3000.
User Name The login user name for the device.
Password The login password for the device.
Video Channel The total number of video channels owned by the device.
After checking, the system automatically adds the device to the
lmport to Group
custom list and creates a group (the same as the device name).
After checking, the system automatically adds the device to the
Alarm Input
custom list and creates a group (the same as the device name).
Alarm Output Number of alarm output ports owned by the device.
Connection Mode Select TCP, MCAST (SRTP), or MCAST (RTSP) modes.
If you add a device that is not activated, you can check Auto Activate
Automatic Activation
to activate the device.
2. Select the [Add Device] mode in the [Add Device] window, fill in the corresponding
22
User Manual
information, and check whether to add a device offline and whether to import a group
as required.
3. After entering the correct information, click [Add], and the display shows that the
device is added successfully. The added device information appears in the list, as
shown in the following figure.
Explain：
The device connection status is green for online devices and red for offline devices.
3.1.3 Modify
Operation steps:
1. Check the device to be modified in the added device list, and click the [Modify]
button to pop up the [Modify Device] window, as shown in the following figure.
23
User Manual
2. Click the "Modify" button to show "Modify Successfully".
Notice：
Only one device can be modified at a time.
3.1.4 Delete
Check one or more devices to be deleted in the list of added devices, click the [Delete]
button to enter the [Device Delete] interface, and select [OK] to delete them
successfully.
3.1.5 Invert Selection
In the list of added devices, check one or more devices that do not need to be operated
on the current page, click the [Invert Selection] button, and select all devices except
24
User Manual
those in the currently selected range to perform the [Invert Selection] operation on the
selected devices.
3.1.6 Refresh
Click the [Refresh] button in the [Device List] to refresh the information of all devices on
the current interface.
3.2 Decoding device
All operations are the same as the coding equipment management. Refer to 3.1
Coding Equipment.
3.3 Gate Equipment
Click [Gate Equipment] on the [Equipment Management] interface to enter the
gate equipment interface, as shown in the following figure.
Click the [Add] button to add the man gate equipment, as shown in the following
figure.
25
User Manual
Operation steps:
1. The equipment serial number is the factory number of the personnel gate
equipment, which can be obtained from the web interface of the personnel gate
equipment [Configuration-System Settings-System Maintenance-System Upgrade],
such as ID0602181090922201900XXX.
26
User Manual
2. When connecting the gate equipment, it is necessary to note that the port number is
80.
3. If the device is configured as a PAD, you need to enter the PAD interface [Main
Menu-Communication Settings-Network Settings] to change the server address to the
IP address of the computer where the client is located, so that the PAD and the client
can communicate.
4. Enable the intelligent application picture collection function in the client [System
Settings-Intelligent Application] to ensure that the client can receive the pictures of the
human gate equipment.
3.4 Group
In the [Device Management] interface, enter the [Group Management] interface, as
shown in the following figure.
27
User Manual
The interface parameters are described as follows:
Parameter Instruction
Set the channel name on the local device tree synchronously to the
Sync to device
front-end channel.
Obtain the front-end channel name of the online channel in the device
Get Device Name list; if the channel name is modified locally, clicking [Obtain Name] will
not obtain the front-end channel name.
Obtain the alarm input and output information of IPC and NVR
Get alarm port
equipment.
Tick and select a Customized list group, click to delete the group and
Delete Group
delete the sub-groups and channels in the group at the same time.
Tick and select the channel in left Device list, select a group in right
Import Customized list, click to import the device to the customized device
list.
28
User Manual
Tick and select the channel in Customized list group, click to export
Export
that channel.
Quick search of channel name, input key information and the channel
name including that key information will be displayed in Device list
and Customized list.
Sync to device, move the mouse to Device list channel node, click
synchronize the channel name to the front-end channel.
Get the name, move the mouse to Device list channel node, click to get
the front-end channel name of single channel.
Modify channel name, move the mouse to Device list channel node,
（in Device list） click to modify the channel name
Upon acquiring the alarming port information of the present
equipment list channel, click to modify the name, No. and descriptions
（in alarm list）
of alarming port.
Add group, move the mouse to Customized list group, click to add the
sub-group of the group.
Modify watch point group, move the mouse to Customized list group,
（in Customized list） click to modify the name of the watch point group
Delete group, move the mouse to Customized list group, click to delete
（in Custom List
the group, and delete the sub-groups and channels in the group at the
Grouping）
same time
Explain：
29
User Manual
The information in the [Equipment List] is the information of all the added encoding equipment
and their channels automatically generated by the system.
[User-defined list] User-defined grouping information.
Users can add the encoding equipment and its channel in [Equipment List] to [Custom Group]
according to their own needs, which is convenient for users to manage.
3.4.1 Add device to custom groups
For example, add all channels of the device 192.168.14.68 in [Device List] to the
custom group [Test Group] in [Custom List].
Operation steps:
1. Check all channels of 192.168.14.68 in [Device List].
2. Select (highlight) the custom group to be added in the [Custom List], as shown in the
following figure.
3. Click "Import" to void and add lines.
Explain：
Select the corresponding device channel in the [Custom Group], and click the [Move Out]
button to delete the device channel from the custom group.
30
User Manual
All modules except the device management module load the custom device list, and the user
needs to add the device to be used to the custom list.
3.4.2 Modify the channel name
In [Device List], slide the mouse to the corresponding channel name and click " " to
modify the channel information and set the decryption password of the encrypted
channel, as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
Name Modify the name of the current channel.
Type Support channel and bayonet.
Modify the connection mode to support TCP, MCAST (RTSP) and
Connection mode
MCAST (SRTP).
Default decryption password Set the video channel encryption password here.
31
User Manual
3.4.3 Get and modify the device alarm port
Operation steps:
1. Select the corresponding device in the [Device List], and click the [Obtain Alarm
Port] button. The alarm port will appear under the device, as shown in the following
figure.
2. Select the corresponding alarm port and click " " to pop up the [Modify Alarm Port]
window, as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
Obtain the information about the present alarming port and
Type of alarming port
support two types of ports, i.e., alarm input and alarm output.
Name of alarming port Name of alarming port can be self-defined.
32
User Manual
The No. of alarming port can be self-defined (ensure port No.
No. of alarming port
cannot be repeated).
Obtain name of the present host automatically. Modify host name
Host name
by Equipment-> Coding device -> Modify.
Host IP Obtain the IP of the present host automatically
Descriptions of alarming For encrypted channels, the default is to use the set decryption
port password for decryption.
3.4.4 Modify group
Select the list grouping in [User-defined Grouping], and click " " to pop up the [Modify
Monitoring Point Group] window, as shown in the following figure.
3.4.5 Delete group
Check the list grouping in [Custom Grouping], and click "Delete Grouping" to pop up a
confirmation box. After confirmation, you can delete the grouping. Multiple selections
or all selections can be deleted, as shown in the following figure.
33
User Manual
34
User Manual
4 Live view
View the real-time picture of the monitoring point, and perform live service
operation on the monitoring point.
4.1 Custom Device List
Select [Custom Device List] to display all custom grouping lists, and enter information
in the [Search Box] to fuzzy search the corresponding channel or port, as shown in the
following figure.
4.1.1 Customize the device list with the right-click menu
Right click on [Custom Device List] to pop up a right-click menu, as shown in the
following figure.
The related Parameters are described as follows:
Parameter Instruction
35
User Manual
Turn off all videos Turn off all videos connected at that moment.
All the videos in current list are added and played in main code stream
Main code stream mode (as for the channel being played, the playing code stream will
not be changed)
All the videos in current list are added and played in subcode stream
Subcode stream mode (as for the channel being played, the playing code stream will
not be changed)
Time calibration Conduct time calibration on on-line devices in all group lists.
Manual alarm Cancel the current alarm in the channel in video manually.
4.1.2 Device grouping right-click menu
Select a group in Device list and click right key, the right key menu of device group list
will pop up, as shown in below figure.
The related Parameters are described as follows:
Parameter Instruction
Turn off all videos Turn off all videos connected at that moment.
Turn off this video Turn off all videos connected in current group.
Added to the list of switch
Add selected encode device to automatic switch group list.
groups
36
User Manual
All the videos in current list are added and played in main code stream
Main code stream mode (as for the channel being played, the playing code stream will
not be changed)
All the videos in current list are added and played in subcode stream
Subcode stream mode (as for the channel being played, the playing code stream will
not be changed)
Time calibration Conduct time calibration on on-line devices in selected group lists.
Manual alarm Cancel the current alarm in the channel in video manually.
4.1.3 Device channel right-click menu
Select a channel watch point of a device in device list group, click right key, the right
menu of device list will pop up, as shown in below figure.
The related Parameters are described as follows:
Parameter Instruction
Collect Add the channel to [Favorites].
Soft boot When the device is in the soft shutdown state, click Soft Startup to
37
User Manual
start the device. Suitable for low power consumption series
products.
When the device is powered on, click Soft Shutdown to shut down
Soft-off
the device. Suitable for low power consumption series products.
Login to the affiliated host Right click on the device channel to restore the connection between
computer the device host to which the channel belongs and the platform.
Log off the affiliated host Right click on a device channel to disconnect the device host to
computer which the channel belongs from the platform.
Turn off all videos Turn off all videos connected at that moment.
In the channel of login encode device, click this button to connect
Main code stream
the main code stream video of the channel.
In the channel of login encode device, click this button to connect
Subcode stream
the subcode stream video of the channel.
In the channel connected to video, click this button to disconnect
Video interruption
the video of the channel.
In the channel of login encode device, click this button to talk to the
video source of the channel. Click this button in the channel of
DVR/NVR device, the intercom box "Talking to XXXX" will pop up to
Start intercom
start talking with DVR/NVR; click this button in the channel of IPC
device, the intercom box "Talking to XXX" will pop up to start talking
with IPC device.
Stop intercom In the channel of login encode device, click this button to stop the
38
User Manual
intercom with video source of the channel.
Time calibration To conduct time calibration on this on-line device.
Change channel name Change the name of currently selected channel.
Manual alarm Cancel the current alarm in the channel in video manually.
4.1.4 Alarm entry port right-click menu
Select the corresponding alarm input port in the group in [Device List], and right click
to pop up the context menu of the alarm input port, as shown in the following figure.
The related Parameters are described as follows:
Parameter Instruction
Manual alarm If the equipment alarm inputs alarm, click “Manual alarm
cancellation cancellation” to clear the alarm in process.
4.1.5 Alarm output port right-button menu
Choose one alarming output port in group in the equipment list, click the right key and
the right key menu of equipment list will pop out, as shown in the figure below.
The related Parameters are described as follows:
Parameter Instruction
Open/close alarm output Control the on/off status of alarm output port.
39
User Manual
4.2 Video preview window
The right side of the [Video Preview] interface is the video preview window.
Double-click to maximize it. Double-click again to restore it. When the main video is
previewed, the split-screen window supports self-adaptation according to the number
of linked videos, and supports real-time video playback by devices added in various
ways.
The video played in real time supports watermark by default, and the watermark
information displays the current client login user, the computer IP of the client, and the
device channel name. The user can configure the watermark display in [System
Settings-Video Related].
Notice：
Only the administrator user of the VMS client can configure and turn off the watermark display.
The target bar below the main video can display face information, age, gender,
whether to wear a mask, whether to wear glasses and body temperature. The target bar
on the right side of the main video shows similar results compared with the face
database (strangers are not displayed), as shown in the following figure.
40
User Manual
4.2.1 Video preview window displays the information
When the video is previewed, the lower left status bar of the video supports closing
the video, audio preview, snapshot video and instant playback.
The channel name can be displayed in the lower left corner of the main video
screen. When the alert is turned on, the alert icon is displayed in the upper right corner
of the video window. When it is turned off, the alert icon is cancelled.
Low-power battery series products can display the battery level and the playing time in
the upper left corner of the screen, as shown in the figure below.
41
User Manual
Click the battery icon to pop up the [Battery Management] interface to switch the
power mode of the device, as shown in the following figure.
42
User Manual
4.2.2 Video preview window toolbar
When browsing the channel video, you can continue to operate the channel in the
lower toolbar of the screen, as shown in the following figure.
The icon description is as follows:
Icon Explain
Disconnect the current channel video
Turn on/off the video sound of the current channel
Turn on the intercom
Capture current channel video
Record the current channel video
Enter the instant replay interface
Fisheye expansion, see 4.11 Fisheye expansion function for details.
Intelligent detection, supporting high-altitude parabolic alarm and
electric vehicle detection alarm settings, requiring equipment
support.
Manual one-key alarm elimination
4.2.2.1 Intelligent detection
Support high-altitude parabolic alarm and electric vehicle detection alarm settings,
requiring equipment support.
43
User Manual
The interface description is as follows:
Function Explain
Set the sensitivity. The larger the value is, the more sensitive it is.
Sensitivity The detection rate will increase, and the false detection will also
increase.
When checked, a character prompt is displayed when an alarm is
Overlay text tips
triggered.
Displays the alarm rules When checked, the Alarm Rule box is displayed.
Displays the trace When checked, the trajectory of the dropped object is displayed.
44
User Manual
The interface description is as follows:
Function Explain
Set the maximum and minimum size of the target, which represents
Target Max/Min Size
the percentage of the target width in the picture.
Set the sensitivity. The larger the value is, the more sensitive it is.
Sensitivity The detection rate will increase, and the false detection will also
increase.
Set the alarm threshold, support the input range of 2 ~ 3600 values,
alarm threshold that is, the alarm occurs when the electric vehicle stays beyond the
threshold.
Displays the alarm rules When checked, the Alarm Rule box is displayed.
Display the target When checked, the test object is framed.
45
User Manual
4.2.3 Video preview screen toolbar
When browsing the main video preview, the operation functions of the main video
interface can be displayed in the lower toolbar of the main video screen, as shown in
the following figure.
The toolbar icons in the video preview interface are described as follows:
Icon Instruction
Capture all, to capture windows of all connected videos at current
screen.
Start all recording, record windows of all connected videos at
current screen.
Intercom list, display current intercom status.
3D control, adjust the scene to be monitored to the video center
through mouse click control. Specific operations:
1. Left click on the monitoring video screen and move the
corresponding point to the center of the video;
2. Hold down the left button and pull down a rectangular area to the
right, then move the center of the designated area to the center of
the video and zoom in;
3. Hold down the left button and pull out a rectangular area to the
46
User Manual
top left, then move the center of the designated area to the center
of the video and zoom out to view it.
Electronic zoom-in. After this function is enabled, select the channel
picture and slide the mouse wheel to zoom in the picture. After
zoom-in, drag the picture. After dragging to a certain part of the
picture, you can continue to zoom in.
Connection status. Shows/does not show how the channel is
connected.
Save view and the user can save the current information.
Rotating display plan, allow users to set their own switch mode, so
that software can automatically switch video channels on
[Real-time preview] interface for users’ convenient browse.
Start rotating display, automatically switch video channels to
preview according to rotating display plan.
Group switching list, click this button to display group switching list.
There will have devices in the list only when right click the device
group in customized device list of device list on the left to select and
add devices to [Add to group switching list].
Last group, which supports the manual switch group to switch the
last screen of group.
Start/Stop group switching, open video window, click this button to
conduct group switching; click again to stop group switching.
47
User Manual
Next group, which supports the manual switch group to switch the
next screen of group.
Set number of video views, click and the setting menu of displayer
will pop up.
Full screen, click to display video window at full screen. Click ESC
button or right click the video to cancel full-screen display to escape
from full-screen model.
Indicate that the video connecting status is direct connection
The video is currently experiencing an alarm.
Turn off the video, i.e. disconnect the connection of present video.
/ Turn on audio / Turn off audio
Screen capture, capture the picture of the present video。
Turn on tape recording / turn off tape recording
Instant replay, which supports timely view of present playback
based on demands. The time of instant replay can be modified
according to System settings -> Video-related -> Time of instant
playback.
Return to preview to exit the page of instant playback.
4.2.4 Video preview window right-click menu
Operation steps:
Right-click the main video browsing window to pop up the right-click menu of the
48
User Manual
video preview window, as shown in the following figure.
The related Parameters are described as follows:
Parameter Instruction
Click on the single video window of connected video to turn off the
collect
video in the window.
Click on the single video window of connected video to listen to the
Turn off the video
audio of video channel in the window.
Click on the single video window of connected video to take snap
Audio pre-view
shot of the window.
Adjust the video's aspect
Electronic amplification and fast ball 3D control are available.
ratio
Click on the single video window of connected video to turn off the
control
video in the window.
Electronic amplification Same as the icon of the video preview window toolbar“ ”。
Fast ball 3D control Same as the icon of the video preview window toolbar“ ”。
49
User Manual
Switching of main code and Auto switch between main code and subcode streams. Support
subcode streams simultaneous switch among native video.
Set the display parameter of currently selected video: brightness,
Video parameter
contrast, saturation and Hue.
Time calibration Conduct time calibration on the on-line device.
Change channel name Change the name of currently selected channel.
Full screen Display video view window at full screen.
Manual alarm Cancel the current alarm in the channel in video manually.
Device support is required. See 4.11 Fisheye Deployment Function for
fish eye expanslon
details.
Device support is required. The watermark can be displayed on the
Watermmark
video interface.
4.3 Cruise Plan
The main function of the polling plan is to allow users to set their own switching mode,
so that the platform can automatically switch video channels in the [real-time preview]
interface, which is convenient for users to browse.
Operation steps:
1. Add a view. After configuring the split-screen scheme and the video to be played
according to the above operations, click the " " button in the toolbar of the preview
interface and enter the customized [view name] to save the view, as shown in the
following figure.
50
User Manual
2. Add a polling schedule. First, click the view bar on the left, select the view to be
added, and then right click to pop up the right-click menu, and select [Add to polling
plan] in the menu, as shown in the following figure.
3. Set the polling schedule. Click " " in the toolbar of the preview interface at the
lower right corner to enter the interface for setting the polling plan, as shown in the
following figure.
51
User Manual
4. Enable/disable the polling plan. Click the " " button in the toolbar of the preview
interface at the lower right corner to enable the polling plan, and click again to close
the polling plan.
4.3.1 Modify the cruise intervals
Check the view to be modified and click the [Modify] button to change the polling
interval, as shown in the following figure.
4.3.2 Delete view
Check the view to be deleted and click [Delete] to delete the view, as shown in the
following figure.
4.3.3 Move view
Operation steps:
Check the view to be moved and click the [Move Up]/ [Move Down] button to adjust
52
User Manual
the view playback order.
4.4 Group switch set
Operation steps:
1. Create a group cut. Right click the group in the [Custom Device List] column, and
click [Add to Switch Group List] to create a group switch and pop up a prompt box, as
shown in the following figure.
2. Set up group cuts. Click the " " button in the toolbar of the preview interface at
the lower right corner of the main video to set the group switching time interval and the
number of group split screens, as shown in the following figure.
53
User Manual
Notice：
Set the time interval of group cutting: set the time interval of group cutting on the upper part of
the interface, and the value range of the time interval is 30 ~ 3600 s.
Set the number of split screens, support-×-screen (do not change the number of split screens,
keep the original number of split screens), 1 × 1 screen, 2 × 2 screen, etc.
4.4.1 Modify number of components
Operation steps:
1. Click the [Modify] button to enter the interface for setting the number of split
screens.
2. Double-click the number of split screens in the group to enter the interface for
setting the number of split screens, as shown in the following figure.
4.4.2 Open/close group switch
Click the " " button in the toolbar of the preview interface at the lower right corner
of the main video to open the group cutting, and click again to close the group cutting.
54
User Manual
4.5 Target information
Below and on the right side of the main video interface of the real-time preview, the
information of the identified person and the information in the comparison face
database are displayed respectively, as shown in the following figure.
Explain：
Target information can identify the age, gender, whether to wear masks, whether to wear
glasses, temperature detection and detection time of personnel in real time.
At the same time, it can identify whether the person is a person in the face database, if so, it will
be compared with the picture uploaded in the face database, and the similarity, the name of the
person and the detection time will be displayed.
If you want to view the previous records, you can switch to [History] to view the history
information.
4.6 Favorites
Operation steps:
1. Collection Channel. Right click the channel menu under the grouping in the [Device
List] column and select Favorite, or right click the currently playing screen and select
[Favorite] to collect the channel.
2. View favorite channels. Select [Favorite] in the drop-down box on the upper left to
55
User Manual
see the favorite channels, as shown in the following figure.
4.7 View
Select [View] in the drop-down box on the upper left to display the currently saved view.
Double-click to preview the view information. Right click the list view node menu to
pop up an interface, as shown in the following figure.
The related Parameters are described as follows:
Parameter Instruction
Name change Click to change view name.
Add to the regular rotating
Click to add the view to the regular rotating switch plan list.
switch plan
Delete Click to delete this view information node from view list.
4.8 PTZ Control
Expand the [PTZ Control] list on the left side of the interface to display the PTZ
56
User Manual
operation interface. The PTZ control can control the PTZ speed, preset position, etc., as
shown in the following figure.
The cradle control icon is described as follows:
Icon Instruction
8-direction key, press corresponding direction key to control PTZ to
rotate in the direction accordingly; the center button is scan shortcut
key.
Zoom control button, press " " to control the device to perform
zoom-out operation, the field of view angle becomes larger and the
/ scene becomes smaller; press " " control device to perform
zoom-in operation, the field of view angle becomes smaller and the
scene becomes larger.
Focus control button, press " " to control the device to perform
focusing-in operation, the near scene is clear and the far scene is
/
fuzzy; press " " to control the device to perform focusing-out
operation, the far scene is clear and the near scene is fuzzy.
/ Aperture control button, press " " to control the device to perform
57
User Manual
aperture reduction operation, press " " to control device to
perform aperture enlargement operation.
The slider can adjust the rotation speed of the device.
Set the preset number for calling.
Call the preset. Select saved preset, click to call and the screen will
jump to the preset part.
Set the preset. Select the preset number to be saved, adjust the
screen to the preset to be saved, click Set to save this position.
Click to expand or hide advanced features. Advanced features
include lights and wipers, which can be switched on and off.
4.9 Unlocks the encrypted channel function
The video can be played normally by entering the correct password in the prompt box
for entering the password in the playback screen, as shown in the following figure.
58
User Manual
4.10 Fish eye unfold
Operation steps:
1. Right click and select [Fisheye Expansion] during video preview, or click the " "
icon in the menu bar at the lower left corner of the video screen to pop up the [Fisheye
Expansion] window.
2. There are three installation methods, which are "installation", "wall installation" and
"ground". As shown, the following is "installation".
3. In the [top installation] installation mode, the display mode is to select [fisheye +
3ptz] as an example, and the rest is similar to this operation. The left screen in the small
window is the fisheye screen, and the remaining areas are the other three screens. In
these areas, the screen can be enlarged. After selecting a specific area, the screen can
be dragged by using the PTZ control. You can control the speed of the drag by
controlling the speed bar. Click " " in the PTZ control, and the selected screen will
cruise according to a certain track.
4. The remaining display modes are the same as the [fisheye + 3ptz] operation.
59
User Manual
4.11 USB keyboard control
Enable the joystick keyboard in [System Settings-Common Settings].
Operation steps:
1. Connect the keyboard to the computer and click the connection status icon to
display the instruction manual, as shown in the following figure.
2. Click the Debug button to debug the keyboard, as shown in the following figure.
60
User Manual
3. Use the keyboard to control the preview operation according to the instructions.
61
User Manual
5 Video playback
Search and play the video file of the monitoring point, and perform playback service
operation on the monitoring point.
5.1 Video query
Operation steps:
1. In the [Video Playback] interface, click the monitoring point on the left to set the
query time range, as shown in the following figure.
The function parameters are described as follows:
Parameter Instruction
62
User Manual
Select the time range to be queried. The maximum query range is
Time Range
seven days.
Choose remote storage, local storage, or cloud storage. Remote
storage: the video stored in the storage medium of the ipc. Local
Storage Location Storage: Video stored on the computer disk where the VMS software is
installed. Cloud storage: The P2P account device is available, and the
device needs to open the cloud storage service on the APP.
Remote storage and local storage support. Select the stream type of
Stream Type
video recording.。
Remote storage support. Select the video type to be queried,
including All, Manual Video Recording, Timing Video Recording and
Warning Video Recording. Playback by video type is supported. For
Recording Type
example, if the video type is selected for query, only the color bar of
the alarm video is displayed on the playback axis, and only the
Warning video is played.
2. After selecting the condition, click the query button to display the query result
prompt box, as shown in the following figure.
63
User Manual
3. Click [Query Result] below to see the current result, as shown in the figure below.
Explain：
For more accurate query, you can click the [More] button to set the storage location and code
stream type filter conditions for query. Click the [More] button again to hide the detailed filter
conditions.
Select the time range. On the time range start calendar, select the start time. On the end time
calendar, select the end time.
When the storage location is selected as front-end storage, the following code stream types can
be selected, and two code stream types of main code stream and sub-code stream are supported.
The query result will be displayed on the progress bar after the query result is obtained, which
can be played back by clicking the time point on the progress bar.
Synchronous playback is supported, and four-way synchronous playback is supported at most.
64
User Manual
5.2 Video playback
Play mode 1: Click [OK] in the query result prompt box to play back the first video file of
the query result.
Playback mode 2: Select a video file in the query result and click " " in the operation
bar to play back the file.
Playback mode 3: Select a playback window and directly click the time point on the
timeline to play back from that time point.
5.3 Playback control
In the video playback interface, display each function key in the playback control menu
bar. The playback control menu is shown in the following figure.
The icon function is described as follows:
Icon Instruction
Video type filter button. Click it to filter the video timeline type. The
unselected video type will not be displayed on the timeline, but will
continue to play. Support the screening of all formats, alarm video,
timing video and manual video.
Window 1 Displays the current window number.
Click to configure daylight saving time. Once configured, the Playback
Timeline will be displayed according to the Daylight Saving Time
setting.
65
User Manual
On/off synchronous playback; asynchronous playback is set by
default. Click to enter synchronous playback mode and click again to
exit it. Note: Synchronous playback not supported for local video.
Slow forward button, click to make the video file play slowly.
Note: as for the equipment added by P2P direct connection, click the
“slow play” button to slow from 4x to 2x and from 2x to 1x. 1x speed
is the slowest. 1/2 speed is not supported.
Fast forward button, click to make the video file play quickly.
Note: the equipment added by P2P direct connection supports 4X
speed playing at most.
/ Play/Pause button, click to control the start/pause of video file.
Step forward button, click to make the video file play frame by frame.
Stop button, click to stop the playback of current video file.
Capturing button. Click it to capture the video file that is selected and
being played.
Video clip button: click it to start video clip and click it again to finish
that. The time axis of clipped section will become red and the target
section will be saved. The format of video saved can be modified by
setting “system settings -> video -> download video format”; three
formats sdv ,mp4, and avi are available.
Set screen number button, click to pop up the menu of playback
window split screen.
66
User Manual
1×1 screen playback supported, click and the video playback window
will display in single screen.
Same as " " in real-time preview 4.2.1.
Volume adjustment bar, drag to adjust the sound of video playback.
Click on the horn to turn sound on/off.
/ Used to adjust the accuracy of time axis.
5.3.1 Replay window right-click menu
Right-click the video playback window to pop up the right-click menu of the playback
window, as shown in the following figure.
The related Parameters are described as follows:
Parameter Instruction
Stop playback Click to stop the playback of current video.
Snap shot Click to snap shot of selected playback window.
Change channel name Click to change channel name of selected playback window.
Click to display the playback window at full screen. Click again to turn
Full screen
off full screen display.
Device support is required. See 4.11 Fisheye Deployment Function for
fish eye expanslon
details.
67
User Manual
Device support is required. The watermark can be displayed on the
Watermmark
video interface.
5.4 Video download
There are two ways to download videos: download by file and download by time
period.
5.4.1 Download by file
Operation steps:
1. Batch download. Click the query result in the [Video Playback] interface to pop up
the query result interface. After checking multiple video files, click the [Download]
button to download them in batches, as shown in the following figure.
2. Select [Download List] to enter the export progress list interface to view the progress
of downloaded files, as shown in the following figure.
68
User Manual
3. Stop the export. Select the file to be exported in the export progress list, right click
the file, and select [Stop Export] to stop downloading the file, as shown in the following
figure.
4. Re-export. Select the file to be re-exported in the export progress list, right click the
file, and select [Re-export] to re-export the file for download.
5. Clear the record. Right-click a file in the export progress list and select [Clear Record]
to delete the downloaded record.
6. Clear all. Right-click a file in the export progress list and select [Clear All] to delete all
download records in the list.
Notice：
When downloading video files, only one video file can be downloaded at the same time.
69
User Manual
5.4.2 Download by time period
Select the channel you want to download through the drop-down menu or by clicking
the channel in the tree list, select the time period you want to download, and then click
the [Download by Time Period] button.
5.5 Recently browse
Record the recently viewed video. Click the query result in the [Video Playback]
interface to pop up the query result interface. Click [Recent View] to quickly preview, as
shown in the following figure.
5.6 Fish eye unfold
See the real-time preview 4.10 fisheye expansion function for details.
70
User Manual
6 System configuration
Configure common client operations.
6.1 Common Settings
Click [Common Settings] in the [System Settings] interface to display the function items
of [Common Settings], as shown below.
The interface parameters are described as follows:
Parameter Instruction
Tick and select, after fill in correct [User name]
Login Settings Automatic Login Software and [Password] by users, the software will realize
automatic software login function when the
71
User Manual
operation system starts.
Set the language of software system, effective
Language
after restart.
System
Set the skin of software system, effective after
Skin
restart.
Backup: Backup all configurations, devices, etc. Of
the current program. Restore: Import the backup
file to restore the program to the state when it was
backed up. Scheduled backup: backup operations
are performed on a scheduled basis. Restore
factory settings: restore factory settings. Rebuild
Data backup path
index: scan all disks of the computer where the
Data backup stand-alone version is located, and automatically
generate records and save them to the database
after finding the files saved by the stand-alone
version (such as intelligent analysis pictures,
manual video files, etc.).
Import/export relevant configuration information
Configuration with one key, such as equipment list, user
authority and electronic map.
Period of keeping
Log Settings Set the save time of each operation log.
operation log
72
User Manual
Period of keeping alarm log Set the save time of each alarm log.
Restore the configuration of current page to the
Restore Default
configuration information when initially installed.
Set whether to enable the joystick keyboard; if
Peripheral related not, the joystick keyboard cannot be used by the
client after it is inserted into the computer.
6.2 Video Settings
Click [Video Related] in the [System Settings] interface to display the [Video Related]
function item, as shown in the following figure.
The interface parameters are described as follows:
73
User Manual
Parameter Instruction
Automatically restore the
The video connected to video preview, when turns on the software
state last time you exit
again, the video before turn-off will restore connection.
from the system
Set switching screen number, when the number of windows displayed
Switch between Main and
in the client-side video browsing interface is greater than the number
Sub Streams, Automatic
of split screens, the connected channel video will default to the
Switching Screen Number
subcode stream.
Manual Default Connection Set the code stream type of default play.
Available to set Good fluency/Minimum delay. Take effect after
Play property setting
replaying video.
Software decode and hardware decoding are supported, effective
Decoding mode setting
after restart. Take effect after reboot.
The download recording may set SDV (private format) ,MP4 (general
Video download format
format) and AVI format.
Show or conceal frame rate on preview screen. Take effect after
Preview frame rate
accessing video again.
Automatically restore the
The video connected to video preview, when turns on the software
state last time you exit
again, the video before turn-off will restore connection.
from the system
Set whether to display the watermark in the preview screen of the
Watermark display
[Live Preview] channel. Only admin users can set it.
74
User Manual
Watermark IP selection Select the watermark IP to display.
6.3 Storage management
Click [Storage Management] in the [System Settings] interface to display the function
items of [Storage Management], as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
Continuous recording time Set the time of continuous recording (recording packaging), the
(min) time range is 5~120 min.
SDV format , mp4 format and AVI format are supported for
Record format
recording storage.
75
User Manual
Type of record streaming Main code stream and minor stream supported.
Supported to set by percentage (%) or by space (G), fill in
Min. disk space
corresponding parameter in the text box below.
Supported to select and delete the earliest local recording or stop
Disk full
recording.
Storage location Set the storage location of files.
The save path of capture, preview and playback photo.
Path Setting
The save path of video download.
6.4 Intelligent application
In the [System Settings] interface, click [Smart App] to display the function items of
[Smart App], as shown in the following figure.
Explain：
After the smart application is enabled, it can receive face and human gate pictures, and the
76
User Manual
retention time of snapshot pictures can be defined according to the needs.
After the deletion strategy is checked, this strategy can be executed after the upper limit of
the storage time of passenger flow (which can support 6 ~ 24 months) is reached.
6.5 Record plan
Click [Video recording plan] in [System setting] interface to display the function item of
[Video recording plan], as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
Enable local recording
Check the box to enable the local recording schedule.
schedule
After selecting a device from [Custom Device List] on the left, the
Channel name
corresponding channel name appears.
Code stream types Support main stream and sub stream.
Time template Full-cycle templates and custom templates are supported. Custom
77
User Manual
templates can be set by clicking the " " icon on the right or
dragging the blue slider.
The recording plan configuration of the current channel can be
Copy to
copied to other channels.
Recover Click to restore the settings before the change.
Save Click to save the current configuration.
78
User Manual
7 Alarm management
Real-time display of equipment alarm information, timely understanding of
equipment abnormalities.
7.1 Real-time alarm
Click the [Real-time alarm] option in the [Alarm management] interface to display the
real-time alarm list in the lower area, as shown in the following figure.
Premise:
The device has a storage medium (such as SD card), and is configured with alarm
recording and alarm capture, and the picture receiving function is enabled in the client
[System Settings-Smart Application].
Operation steps:
Double clicking on an alarm record can display alarm information, alarm recording, and
alarm capture in the details section on the right; If the alarm device does not have
79
User Manual
storage media, the alarm information and real-time video will be displayed in the
details on the right.
7.2 History alarm
Click the [Historical Alarm] option in the [Alarm Management] interface to display the
real-time alarm list in the lower area, as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
Starting time Available to set the starting time of history alarm query.
End time Available to set the end time of history alarm query.
You can set the alarm type for querying historical alarms and select it
Alarm type
from the drop-down menu.
Available to set the source of alarm of history alarm query, search by
Source of alarm
key word supported.
Available to set the checking status of history alarm query, including
Status check
all, unchecked and checked.
80
User Manual
User check Available to set the checking user of history alarm query
Click to search history alarm information conforms to search
Query
condition.
Reset Click to restore to default query condition.
Tick and select alarm records need to be checked, click to fill in
Check handling suggestion. Update verification status, verify users, verify
real-time, and process comments after verification.
Output Click to output query results to local device.
Tick and select filter level, the selected level will be displayed in the
Filter level
list, nothing will be displayed if on level selected.
Click to play the video 10s before and after the time of alarm, if there’
Play
s no video, real-time preview will be displayed.
Starting time Available to set the starting time of history alarm query.
81
User Manual
8 TV Wall
Video wall configuration and preview.
8.1 Create layout
Operation steps:
1. After entering the interface, if the TV wall is not configured, select the [Go to
Configuration] option to enter the TV wall configuration interface, as shown in the
following figure.
2. Set [TV Wall Name], select [TV Wall Type] and [TV Wall Layout], and click [Save] to
generate the layout, as shown in the following figure.
82
User Manual
Explain：
[TV wall type] There are two types of LCD and LED, which can be selected according to the
display used.
[TV wall layout]: Support the setting of 1 * 1 ~ 8 * 8 pictures.
8.2 Bind decoding
Operation steps:
1. Add a decoding device on the left side of the interface, as shown in the following
figure.
83
User Manual
Explain：
You can also add a decoding device in the [Device Management] interface.
2. Drag the decoder channel into the layout screen, as shown in the following figure.
3. After selecting the bound output channel, click [Resolution Setting] in the lower left
corner of the interface to set the resolution for the channel, as shown in the following
figure.
84
User Manual
Explain：
Set the resolution to the width and height of a single screen, ranging from 240-1920 in width
and 240-1080 in height.
4. Press and hold the left mouse button and slide to select the bound output channel,
and then click [Merge] in the lower left corner of the interface to merge the selected
channel into one output channel, as shown in the following figure.
Notice：
Only output channels of the same decoder can be combined.
85
User Manual
Merging into regular rectangles is only supported.
5. Click [Cancel merge] to cancel the merging of output channels.
The other parameters of the interface are described as follows:
Parameter Instruction
Display offline channels Display information about channels that are not online
Display the last frame After the network is disconnected, the last frame of the channel is
connected retained.
Clear To clear all the image channels.
8.3 Scene generation
Operation steps:
1. Click [Add Code] in [Coding Equipment List] on the left of the interface to add coding
equipment, as shown in the following figure.
Explain：
The coding equipment added in [Equipment Management] will be displayed in [Coding
86
User Manual
Equipment List] on the TV wall interface.
2. Set [scene name] and code stream.
3. Drag the encoding device channel into the layout screen to complete the binding, as
shown in the following figure.
4. Select a binding channel and click the " " icon in the lower left corner to view the
channel information, as shown in the following figure.
5. Click the " " icon in [Coding Equipment List] to set the decryption password or
modify the polling time for the channel, and click the " " icon to save, as shown in the
following figure.
6. Click the " " icon in [Coding Equipment List] to unbind the channel.
87
User Manual
The other parameters of the interface are described as follows:
Parameter Instruction
Display video Check it to display the video image of the bound channel.
Check it to bind multiple encoding device channels in the same screen
Append mode
and automatically switch according to the polling time.
Clear Remove (delete) all bound encoding device channels.
After selecting a channel, you can divide the output channel into
multiple screens. Each screen supports binding to one encoding
Split
device channel and supports 0-16 split-screen screens. 0 screens
means disabling the output channel.
8.4 Preview & Wall up
Operation steps:
1. Click on "Start Preview" to start previewing the video images of each channel in the
current scene, and click on "Stop Preview" to stop the current preview, as shown in the
following figure.
88
User Manual
2. Click on "One-click wall mounting" to send the current scene configuration to the
bound decoder.
3. The control of the pan-tilt unit is the same as that in Chapter IV 4.8 PTZ control.
8.4.1 Demo Mode
Demo mode: instant display mode. In this mode, as long as the decoder device is added
to the device management and online, the bound decoding output channel is online,
and the online encoding device channel is dragged to the decoding channel, you can
preview and upload it to the wall. This mode does not interfere with the set scene. After
exiting the demo mode, you will return to the set scene.
Operation steps:
1. Click [Demo Mode] in the [Preview & Wall] interface to jump to the [Scene Generation]
interface.
89
User Manual
2. In this interface, you can directly drag the online channel to the decoding channel to
bind and put it on the wall.
Select a channel and click [Split-screen] to divide the output channel into multiple
images. Each image supports binding one channel of encoding equipment and
supports 0 ~ 16 split-screen images.
90
User Manual
9 Vehicle management
Vehicle management is used for entrance and exit control of parking lot or set area,
mainly for information registration and access control of black and white list vehicles
and temporary vehicles.
Premise:
1. Add a LPR device. After successful addition, edit the channel in the group and
change the type from channel to bayonet.
2. The added device has been configured in the web interface.
The device configuration can refer to the following:
1. Select [entrance and exit] in [Configuration-System Settings- Allocation of Resource]
on the device web interface.
2. Select [Event Parameters] in the device web interface [Configuration-System
Settings-Vehicle Detection-Event Parameters] to set the trigger conditions. Then set the
effective time and linkage action according to the use requirements.
91
User Manual
3. If you want to lift the garage pole, you need to connect a peripheral to the alarm
output port of the device and set the port mode in [Configuration-Alarm
Management-Alarm Output]. Whether the port mode is normally open or normally
closed depends on the type of peripheral. Then the linkage output is turned on in the
linkage action.
Notice：
The client does not recognize the vehicle detection or unfamiliar license plate alarm, so the
selection of the alarm type does not affect the use of the VMS vehicle module function.
4. License plates can be added in [License Plate Library Management] and [License
92
User Manual
Plate Management], similar to the white list. The license plates in the license plate
library can automatically lift the pole when entering and leaving the garage.
9.1 Region creation
After entering the interface, if the area is not configured, select the [Go to Configuration]
option to enter the area configuration interface, as shown in the following figure.
9.1.1 Basic Information
Operation steps:
Fill in [Basic Information], set the detention duration and area creation, and click
[Save] to generate an area, as shown in the following figure. After saving, it will jump to
the entry/exit setting interface.
93
User Manual
The interface parameters are described as follows:
Parameter Instruction
Vehicle detention time. 4 default durations can be set. Click to select
Detention duration
and switch to the corresponding duration
Support equipment timing setting, and perform timing immediately
Equipment timing
or automatically.
Reqion Name Fill in the area name
Regional Address Not required, set the area address
Responsible person Not required, set up the area responsible person
Telephone Not required, set up the area responsible person telephone
Total number of
Set up the total number of parking Spaces
parkina spaces
Display the parking space status icon in the area preview interface
Full space reminder
after opening
94
User Manual
Remarks Not required
9.1.2 Entrance/Exit Settings
Operation steps:
Set the entry and exit, and add and delete operations. At most one video device
can be added to each entrance or exit, and at most four entrances or exits can be added,
as shown in the following figure. After saving, it will jump to the on-duty management
interface.
Explain：
Click " " to add an entry or exit, or click " " to delete an entry or exit.
Click " " to add a video device, and click " " to delete a video device.
The bayonet equipment is used to monitor the entrance and exit equipment, and the video
equipment is used to monitor the bayonet equipment and around the gate. Please determine the
installation location of the equipment when using it.
95
User Manual
9.1.3 On duty management
Operation steps:
1. Set the on-duty account and on-duty team members, as shown in the following
figure.
2. Click the [Add] button under the on-duty account to add an on-duty account and
assign permissions. The account will be added to the ordinary user of the stand-alone
version synchronously. By default, the name of the on-duty team will be set in order, as
shown in the following figure.
96
User Manual
3. The on-duty account can be edited and deleted, and the name of the shift team can
be modified, as shown in the following figure.
4. Click the [Add] button under the duty member to add a duty member to the duty
group, as shown in the following figure.
97
User Manual
5. You can edit and delete the on-duty members, and modify their names and phone
numbers, as shown in the following figure.
6. Click [Next] to enter the black and white list interface.
9.1.4 Black and White List
Operation steps:
1. Set the black and white license plate library as shown in the following
figure.
2. Click [Add Whitelist] to add a white license plate library, as shown in the following
98
User Manual
figure.
3. Click the icon next to the whitelist library to edit the name and delete the whitelist
library, as shown in the following figure.
4. Click the [Add] button to add white license plate information, as shown in the
following figure.
5. Click " " on the right side of the interface to export the white license plate
template, as shown in the following figure.
6. Click the [Import] button to import the white license plate file and import the white
license plate information in batches.
99
User Manual
7. Click the [Export] button to export the white license plate library information.
8. After entering the keywords, click [Query] to query the white license plate
information.
9. Click the [Synchronize] button to synchronize the white license plate information to
the exit/entrance.
Explain：
To use the synchronization function, the license plate library needs to be bound to the
entry/exit first.
10. The interface and operation of the blacklist are basically the same as the whitelist.
11. Click [Next] to enter the area binding interface.
9.2 Region binding
Bind the bayonet and video for the entrance/exit, as shown in the following figure.
100
User Manual
The interface parameters are described as follows:
Parameter Instruction
Name In/out name port.
For exit or entrance, click [Details] to jump to the [Exit/Entrance
Type
Setting] interface.
Select the added bayonet device for binding, or click " " to pop up
Bayonet device the automatic search interface, and add the bayonet device for
binding.
Select the added video device for binding, or click " " to pop up the
Video device
automatic search interface, and add a new video device for binding.
Select the blacklist license plate library and click [Details] to jump to
Blacklist
the [Blacklist and Blacklist] interface.
Select the white list license plate library and click [Details] to jump to
Whitelist
the [Black and White List] interface.
Set the traffic mode for temporary vehicles that are not in the black
and white list.
Manual registration: temporary vehicle parking is required, and the
Mode of passage
information is manually registered.
Automatic registration: No need for temporary vehicle stop, automatic
registration of information.
Select the duty team. After selection, the list of duty team members
On duty team
will be displayed in the blank box.
101
User Manual
Explain：
The binding bayonet device shall be used after the relevant algorithm is configured.
The operation of the entry/exit binding is the same.
The bayonet devices bound to the entrance/exit cannot be the same.
Click [Save] to automatically jump to the [Area Preview] interface.
9.3 Area Preview
Preview the entrance and exit of the setting area, as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
When the administrator user admin is used to log in, the duty group is
On duty team not displayed; when the ordinary user is used to log in, the duty group
of the on-duty personnel is displayed.
Total parking Displays the total number of parking spaces set when the area is
space created.
102
User Manual
The remaining available free parking spaces are displayed, and all
Remaining registered and released vehicles (including temporary vehicles and
parking spaces white list vehicles) entering the area will occupy the parking spaces,
and will not occupy the parking spaces after leaving the area.
Enter a dwell time, such as 24 hours, to view the number of vehicles
Parking vehicles
that have been there for that time.
Show whether the parking space
Parking space status
is full.
The real-time pictures of the entrance/exit bayonet equipment are
displayed respectively. In the following four pictures, the leftmost
picture displays the video equipment picture bound with the
Entrance/Export
entrance/exit, and the three right pictures display the license plate
photos captured by the bayonet equipment. The photo size needs to
be set in the web interface of the bayonet equipment.
The vehicle registration information is divided into two parts. The upper part is the
real-time license plate registration information, which can be used to register and
release the current vehicle (lift the pole) or prohibit the passage (do not lift the pole).
The lower part is the license plate registration information record, which can be used to
classify and filter all information, entrance information, exit information and
unprocessed information, as shown in the following figure.
Operation steps:
103
User Manual
1. Select different categories to view different vehicle information.
2. Click [Details] to jump to the [Record Center] interface to view the information of the
record and operate it, as shown in the following figure.
3. Click the record center interface [Details] to pop up the vehicle details interface,
where you can view the vehicle information and snapshot pictures, as shown in the
following figure. In this window, you can click Edit to manually modify the vehicle
information, or add the vehicle to the black/white list.
4. After exiting the details pop-up window, return to the [Record Center] interface to
add the vehicle to the black/white list or delete the record.
5. In the [Record Center] interface, you can also query all the vehicle registration
104
User Manual
information in the area. Select the area, entrance, exit and other information, and click
[Query] to view all the vehicles that meet the requirements, as shown in the following
figure.
6. Click [Reset] to reset the query criteria.
7. Check two pieces of data and click [Merge] to merge the two pieces of data into one.
Notice：
Requirements for merging two pieces of data: the two records shall be the same license
plate in the same area, and one is the entry record and the other is the departure record, and the
time of the departure record shall be longer than that of the entry record.
105
User Manual
10 Access Control
Access control equipment management, personnel and permission addition,
real-time monitoring of access control.
Access controller configuration can refer to the following contents:
1. The access controller is directly plugged into the power supply and network cable.
2. After connecting the power supply and network cable, press the button below for a
long time (10 seconds), hear the sound of "drip drip", and restore the factory equipment
successfully.
3. Configure the computer IP to 192.168.1 segment, connect the computer to the
106
User Manual
access controller directly with the network cable, and use the Internet Explorer browser
to access the http://192.168.1.2. The user name is admin, and the password is 1111.
4. After logging in, enter the [Device Management] interface and change the IP address
of the device to the IP address of the computer where the client is located.
5. Enter the [Network Settings] interface, modify the IP address, subnet mask, and
gateway, so that the access control equipment can communicate with the network of
the computer where the client is located.
Notice：
The port number of the network access control device is the start port + 6, and the network port
of the device is the 18807. The network port number of the PC client is the 18809, which is the
open port of the PC client and is used to transmit data with the access controller. If the PC client
cannot receive the data transmitted by the access controller, the problem can be solved by
checking the port occupancy.
After modifying the IP address and web port, you need to log in to the web interface again using
the new IP and port.
For configuration of PAD equipment, please refer to 3.3 Man-brake equipment.
10.1 Basic Configuration
After entering the interface, if the access management is not configured, select the
[Go to Configuration] option to enter the basic configuration interface, as shown in the
following figure.
107
User Manual
10.1.1 Device Binding
Operation steps for adding access control equipment:
1. Add access control equipment in the access control list, click " " next to [Access
Control List], fill in the controller (access control equipment) information and
communication mode in the pop-up window, and add it successfully after saving.
Interface and parameters of access controller are as follows:
108
User Manual
Parameter Explain
Device type Select the access controller.
Controller Name Fill in the custom controller name.
Select the controller type. Note: If the selection is wrong, the device
Controller Type
will fail to add.
Check Batch Add to add access control equipment in batch. Enter the
Batch Add IP address, end IP address and port number. Note that the equipment
should be set with a unified port number.
IP address IP address of the device.
End IP If Batch Add is checked, it is required to fill in.
Port number Fill in the port number of the access control device.
The PAD equipment parameters are described as follows:
Parameter Explain
109
User Manual
Device type Select the PAD device.
Device Name Fill in the custom PAD device name.
IP address IP address of the PAD device.
Port number Fill in the port number 80 of the PAD device.
Fill in the factory number of PAD equipment. Refer to 3.3 Man-brake
Factory number
equipment.
Login name Fill in the login name of the PAD device.
Password Fill in the PAD device password.
Controller information interface:
1. Select the access control device, and the information of the device will be displayed
on the right side, as shown in the following figure.
The interface parameters are described as follows:
Parameter Explain
Controller Name Displays the name of the controller, which you can modify.
Controller Type Displays the type of the controller.
110
User Manual
IP Address Displays the IP address of the controller, which can be modified.
Port number Displays the IP address of the controller, which can be modified.
Check Enable to set automatic timing every day to synchronize with
Automatic timing
the computer where the client is located.
Copy to Copy the configuration of this access control device to other devices.
Manual timing and synchronization with the computer where the
Time synchronization
client is located.
Operation steps for setting controller parameters:
1. Click [Set Controller Parameters] to pop up a window for parameter setting.
The interface parameters are described as follows:
Parameter Explain
When the access controller network is disconnected from the
network, the event log is stored locally. It is divided into cycle
Offline storage mode coverage and storage full alarm.
Circular Overwrite: When the local storage is full, the oldest record is
deleted in a circular manner, and then the storage continues.
111
User Manual
Storage full alarm: when the local storage record is full, it will not be
stored and a storage full alarm record will be generated.
Generally, access control systems require reading and entering
personal passwords before the door can be opened; When
encountering an emergency situation, it is necessary to open the door.
Anti coercion password
At this time, simply enter the anti coercion code after reading the
access card, and the system will sound an alarm at the same time as
opening the door.
Anti-sneak back function: the anti-trailing function of the access
control system requires the card holder to enter from a certain door
and exit from a certain door, and the card swiping records must be
strictly corresponding to one entry and one exit.
Anti submarine return Set the anti-backwash range.
range Door range: the card holder enters from the door and must exit from
the door.
Controller range: the card holder enters from door A of the controller
and exits from other doors of the controller. This range is mostly used
for two-door and four-door controllers.
Operation steps for setting the alarm elimination mode:
1. Click [Set Alarm Elimination Mode] to pop up a window for parameter setting.
112
User Manual
Delay alarm elimination enable: After checking, the alarm will be eliminated after a
period of time. Alarm delay time can be set in [Access Control Authority].
Enable the legal card to eliminate the alarm: After checking, you can use the card
reader of the legal card close to the access controller to eliminate the alarm. Note:
Before using this alarm elimination method, it is necessary to ensure that the access
controller is connected to the card reader.
Operation steps for setting door magnetic port:
1. Click [Set Door Magnetic Port] to pop up a window for parameter setting.
PAD device information interface:
1. Select the PAD device, and the information of the device will be displayed on the
right.
You can view the information of the PAD device and set the device to synchronize time
with the computer where the client is located.
113
User Manual
10.1.2 Holiday Settings
Operation steps:
1. Click [Holiday Setting] to enter the holiday setting interface.
2. Click [Add] and configure the holiday information in the pop-up window.
3. After selecting the holiday, click Download and select the access controller to
download the holiday to the corresponding controller.
114
User Manual
4. Click [Clear Controller Holiday] to clear the holiday settings on the access controller.
10.1.3 Time Template
Set the effective time of the access controller.
Time Period Settings:
1. Click [Time Template] to enter the time template interface and select the time period
setting.
115
User Manual
2. Select the time period number and set 31 time period numbers at most. Drag the
blue bar to modify the time period. Set four time periods at most for each time period
number. Click [Copy To] to copy the time period of this time period number to another
time period number. Click the " " icon to modify the name of the period number.
3. Click [Download] to download all time slots to the controller.
116
User Manual
Schedule settings:
1. Click [Time Template] to enter the time template interface and select the schedule
setting.
117
User Manual
2. When the schedule is selected as [valid all day], it is valid from Monday to Sunday
and holidays.
3. Select the schedule number and set up 31 schedules at most. Each schedule can set
the time period from Monday to Sunday and holidays. Set Timesheet 1. Set Monday
and Tuesday to be valid for the whole day, set Wednesday to be period number 1, set
Thursday to be period number 2, and so on. You can select one period number from 31
period numbers every day, or valid for the whole day.
4. Click [Copy to] to copy the capital involved in this time period table to other time
period tables. Click the " " icon to modify the name of the time period table.
5. Click [Download] to download all time tables to the controller.
118
User Manual
10.2 Personnel Management
Set up people and permission groups.
10.2.1 Permission Group Establishment
1. Click [Add], fill in the name, and add [Permission Group].
119
User Manual
10.2.2 Personnel binding
Create departments and people.
1. Create a department. Place your mouse next to [Department List] and click the "+"
icon to add a department.
2. Click [Add] in the right part to add personnel in the department.
120
User Manual
The interface parameters are described as follows:
Parameter Explain
Name Fill in the name of the person
Gender Select the person's gender
Job ID Fill in the personnel job number
Department Select Personnel Department from Existing Departments
Staff Group That is, permission group. Select the permission group of the person
Card issuing controller Select the access controller
Set the personnel card password; when the door opening mode is
Password card swiping + password, the password shall be input; the password
shall not exceed 4 characters.
3. Enter the card number, select the card permission, and click [Add] to add a card for
the person.
121
User Manual
4. Click [Edit] or [Delete] to edit or delete the card.
10.3 Access Control Permissions
10.3.1 Controller Configuration
1. In the controller configuration interface, you can see the list of all added access
control.
2. Select the access controller or PAD device to be configured, and you can set its
parameters.
122
User Manual
Access controller setting method:
Event logging settings:
1. Configure access controller events, which are card number related and card number
independent. When the event is enabled, a record will be generated when the
corresponding event occurs in the access controller. When the event is disabled, no
record will be generated. Select the schedule to set the effective time of the event. The
schedule can be configured in [Basic Configuration-Time Template].
2. Click [Batch Enable] or [Batch Disable] to enable or disable events in batch.
Set door parameters:
1. Configure door parameters, such as basic parameters, alarm settings, multi-card
door opening, first card door opening, etc.
123
User Manual
The basic parameter interface is described as follows:
Parameter Explain
Door opening time The time when the door is opened by swiping the card or password.
Automatic Door opening Set the automatic door opening schedule. After setting, the door will
Schedule remain open for a period of time within the schedule.
Set the cancellation password schedule. After setting, the password
Cancel Password Schedule cannot be used to open the door in the time period within the
schedule range.
After checking the password to open the door, you can open the door
Password to open door
by entering the password.
Set the password for opening the door. When the password is enabled
Door opening password
to open the door, the door can be opened through this password. This
124
User Manual
password supports 8 characters at most.
After inputting the wrong opening password for three times, it will be
Three error suspension
locked for a period of time, that is, the suspension time. After the
time
suspension time is over, it is allowed to input the password again.
After selecting, enter the anti coercion password to open the door; If
Anti coercion password to not checked, entering the anti coercion password will not open the
open the door door, but an alarm will still be generated. The anti coercion password
can be set in 【 Basic Configuration - Device Binding 】.
The alarm setting interface is described as follows:
Parameter Explain
When enabled, an alarm will be generated when the access control
Illegal door opening alarm
controller experiences an illegal door opening event.
Door opening timeout When enabled, an alarm will be generated when the access controller
alarm opens the door overtime.
Door opening timeout Set the timeout for opening the door; When the opening time exceeds
alarm time this event, an alarm occurs.
The multi-card door opening interface is described as follows:
Parameter Explain
Multi card door opening After the multi-card door opening is enabled, the door can be opened
enabled only after a set number of door cards are used.
Number of multi card door Set the number of multi-card door opening. For example, if the
openings quantity is set to 2, two different cards must be swiped to open the
125
User Manual
door.
Set the timeout, which is the interval. For example, if the timeout time
is set to 10 s, after the first card is swiped, the second card cannot be
Timeout
swiped for more than 10 s, otherwise the first card needs to be swiped
again.
Operation steps for opening the first card:
1. Opening the door for the first time, that is, opening the door for the first time every
day, requires some people to swipe their cards, and then other people's cards can open
the door.
2. Check to enable the first card to open the door, select the personnel card number
from the options to be selected, move it into the options and save it. For example, after
[X] is moved into the selected item, the door must be opened by swiping the card of X
before other cards can open the door.
Countdown door closing operation steps:
1. Countdown closing, that is, select certain people, limit their opening time, when the
126
User Manual
countdown closing time is over, the door will be closed. For the personnel not selected,
the door opening time follows the door opening time set in [Basic Parameters].
2. Check to enable the first card to open the door, select the personnel card number
from the options to be selected and move it into the options to be saved. For example,
after [X] is moved to the selected option, the countdown closing time is set to 10s, and
the door will automatically close 10 seconds after X opens the door.
PAD device setting method:
Basic parameter setting:
1. Configure the basic parameters of the PAD device.
127
User Manual
The basic parameter interface is described as follows:
Parameter Explain
Select the PAD device authentication method, including face, swipe
Host authentication
card, face/swipe card, face + password, face + swipe card, swipe card +
method
password, face + password/swipe card + password.
If the host is connected to an external card reader, set the
Secondary card reader authentication mode of the card reader, including card swiping and
card swiping + password.
Wiegand output Set the Wiegand output protocol.
Wigan output type Sets the Wiegand output type.
Key type Set the key type to normally open or normally closed.
Anti dive return Set to enable/disable anti-reentry.
Door magnetic type Set the door magnet type as normally open or normally closed.
128
User Manual
Door lock action time Set the duration after the door lock is unlocked.
Special user door lock
Sets the duration after the door lock is unlocked for a particular user.
action time
Alarm parameter setting:
1. Configure PAD device alarm parameters.
The alarm parameter interface is described as follows:
Parameter Explain
Coercion card alarm Whether to activate the coercion card alarm.
Local anti disassembly
Alarm when the device host is disassembled.
alarm
129
User Manual
Extemal card reader anti
Alarm when external card reader is removed.
disassembly alarm
External card reader type Normally closed or normally open.
Intrusion alarm Alarm when breaking into the gate.
Door opening timeout
The door opening time exceeds the set time, triggering an alarm.
alarm
Door opening timeout Set the maximum time the door is open.
An alarm is triggered when an illegal card is used more than the set
Illegal card timeout alarm
number of times.
Illegal card exceeding the
Set the maximum number of times an illegal card can be used.
limit
Strangers reported Strangers (people who are not in the face database) are recognized on
multiple times the screen more than a set number of times to trigger an alarm.
Strangers exceeded the Set the maximum number of times a stranger can be identified on the
limit screen.
Illegal password timeout The number of illegal password input exceeds the set number to
alarm trigger the alarm.
Illegal password exceeds Sets the maximum number of times an illegal password can be
the number of times entered.
10.3.2 Permission Configuration
1.Select and highlight a certain permission group and access control device, and
130
User Manual
configure the permission of this access control device for this permission group.
The parameters in the permission configuration interface are described as follows:
Parameter Explain
After the access control device is selected, the currently selected door
Door name
will be displayed.
Whether to grant access permission to this permission group? If it is
Traffic Control checked, all personnel cards in this permission group can be
accessed.
Check to enable password control, that is, after swiping the card, you
Password Control still need to enter the password. This password is set and modified in
HR Management-Personnel Binding.
131
User Manual
Anti submarine return
Check the Enable anti-sneak back setting.
control
Check to enable the holiday setting, otherwise it will not be enabled,
Holiday control
and only the time from Monday to Sunday will be followed.
2.After saving the configuration, click [Download] to download the permission group to
the access controller, click [Copy Permission] to copy the permission to other
permission groups, and click [Clear Download] to clear the permission group on the
access controller and download the selected new permission group.
10.3.3 Interlock Settings
1.Only one of the interlocked doors is allowed to be opened. If the door A is opened, the
door B cannot be opened. Interlock settings are only allowed on the same access
controller.
132
User Manual
2.Click the [Add] button in the upper right corner to add an interlocking door.
10.4 Access Control Preview
10.4.1 Access Control Preview Interface
1. In the access control preview interface, the access control controller can be operated
remotely, such as opening the door remotely, and the real-time monitoring information
of access control can also be viewed.
133
User Manual
The parameters of the access control preview interface are described as follows:
Parameter Explain
Control the door opening once on the client, follow the door opening
Remote door opening
time, and close the back door after the time.
Personnel positioning Click the pop-up search box to view the passers.
Click the pop-up search box to view the people in the door for the
Internal personnel inquiry
corresponding date range.
Remote continuous door Click to open the door, and the door does not close automatically.
opening Click to close the rear door remotely and continuously.
Click to close the door, and the door cannot be opened by swiping the
Remote continuous door
card or password. You need to click to restore the automatic control
closing
before you can use other functions.
Click on the rear door and follow the countdown closing time, after
Countdown door closing
which the rear door closes.
Restore self-control Automatic control of access control equipment is restored.
134
User Manual
10.4.2 Personnel positioning
Support personnel positioning, and query the location and time of personnel card
swiping.
10.4.3 Record Center
The access control history monitoring information can be viewed in the record center.
Select the query condition and click Query to query the access control record.
135
User Manual
Access control extraction record status extraction, you can view the event record
when the access control is offline.
136
User Manual
11 Face recognition
Management and distribution of face database.
11.1 Face database management
11.1.1 Face database addition/modification/delete
Face database add operation steps:
In [Face Database Management], right click [Face Database List] and select [Add] to
create a new face database, as shown in the following figure.
Notice：
The face library name is unique.
Face database modify operation step:
Right click the name of the face library to be modified, select the [Modify] modification
option, re-enter the name of the face library, and click the [OK] button to complete the
modification of the face library.
Face database delete operation step:
Right click the name of the face database to be deleted, select the [Delete] deletion
137
User Manual
option, and click the [OK] button to complete the deletion of the face database.
11.1.2 Face Image Addition
Operation steps:
1. Select the face database to add a face picture, and click the [Add] button to add a
person, as shown in the following figure.
2. Click Next to save the current employee information and create a new employee
details interface.
3. Click OK to save the current employee information and close the current employee
details interface.
4. Click [Cancel] to close the current personnel details interface.
Explain：
Click the [Local Upload] button to upload a face image (note that this item is required).
138
User Manual
Note that the image format is JPG format, the size is between 300 * 300 and 800 * 800, and the size
cannot be greater than 1MB. The image should be kept as clear as possible to facilitate face
recognition.
Enter the name of the person corresponding to the picture, which is required.
Enter the personnel number corresponding to the picture, which is required. Numbering
supports values between 0 and 999999999.
Other information is not required, and the corresponding information can be filled in
according to the actual needs.
11.1.3 Personnel query
After entering the face database management interface, query personnel in the right
area, enter [Name], [Number] and [Gender] in turn, and click the [Query] button to
query personnel.
Explain：
Support query based on name, number and gender.
11.1.4 Add Existing Face Image
Operation steps:
1. Select the face database to be added, click the [Add Existing] button, and select the
person to be added, as shown in the following figure.
139
User Manual
2. Click [OK] to add successfully, and click [Cancel] to close the current personnel
details interface.
11.1.5 Delete (All) Face Image(s)
Select the face image to be deleted and click [Delete] to delete the selected face image.
To delete all face images, click [Delete All] to delete all face images.
11.1.6 Face Image Import/Export/Export All
Operation steps:
1. Click the [Import] button to enter the import operation interface, as shown below.
Click [Download and Import Template] to download the employee information
template.
140
User Manual
2. You can fill in the personnel information according to the downloaded template
content, as shown in the following figure.
Explain：
Check [Personnel Information Table] or [Personnel Information Picture (Name # Job No.)], click
[Select File] to import the file, click [OK] to upload the file, and click [Cancel] to close the interface.
11.2 Face database download
Select [Face Library Download] in the face recognition interface to display its function
content, as shown in the following figure.
141
User Manual
Explain：
In the device list, select the channel that needs to download the face database. This channel
needs to support the face recognition function.
11.2.1 Face library synchronization
After selecting the corresponding channel, click the [Add] button to pop up the
[Face Database] window, as shown in the following figure. Select the face database to
be synchronized, and click [Confirm] to start synchronization.
Explain：
142
User Manual
The synchronization status and synchronization result can be viewed in the current interface. If
the synchronization fails, click the operation result in the [Operation] interface to view the
synchronization failure information, as shown in the following figure. To try to synchronize the
information again, select the synchronization content and click the [Synchronize] button to
synchronize again.
Explain：
Click [Remove] to delete the current face library in the current channel.
Click [Copy to] to copy to other channels.
11.3 Face configuration
Operation steps:
1. After entering the face recognition interface, select [Face Library Configuration] in
the menu in the upper right corner of the left column of the interface to display its
function content in the right column area, as shown in the following figure.
143
User Manual
2. You can set whether to enable the face database and set the similarity. The data
above the similarity is valid and can be recognized.
144
User Manual
12 Access Management
Bayonet preview and information query.
12.1 Gate Management
The human gate management interface is shown in the figure below, and the operation
is the same as that in 10.1 Face Database Management.
12.2 Live View
Select the [Real-time preview] option in the access management interface to display
the video screen of the passenger gate equipment when there is a face, as shown in the
following figure.
145
User Manual
Explain：
In the real-time preview interface, you can view the real-time preview map of the current
monitoring area, and support operations such as opening the gate and lifting the bar of the linkage
equipment.
The IP address of the VMS client needs to be set in the device web side network storage-push
map settings.
12.2.1 Equipment sequencing
Click " " on the right to expand the device list. You can set the real-time preview sorting
of devices and the displayed devices. As shown in the following figure. Select the
equipment to be moved and click [Move Up/Move Down] to change the display order.
146
User Manual
12.3 History of the Gate
In the access management interface, select the [Passenger Gate History] option in the
right column to display the [Passenger Gate History] list screen in the right area, as
shown in the following figure.
Explain：
In the human gate history interface, it supports the search and query of the access area, user
147
User Manual
name and access time.
12.3.1 Access to areas
Select one item in the [Gate History] list, and click the [View] button to view the current
personnel access to the area.
12.4 Checkpoint preview
Premise:
1. Add a device at Device Management-Coding Device. After successful addition, edit
the channel in the group and change the type from channel to bayonet.
2. The added device needs to support the vehicle detection function.
3. Refer to Chapter 9 Vehicle Management for equipment configuration.
In the access management interface, select the [Bayonet Preview] option in the
right column to display the [Bayonet Preview] video screen in the right area, as shown
in the following figure.
148
User Manual
Explain：
In the bayonet preview interface, you can view the real-time snapshot preview of the bayonet in
the current monitoring area, and you can view the current vehicle information.
12.4.1 Device sorting
Click " " on the right to expand the device list. You can set the real-time preview sorting
of devices and the displayed devices. As shown in the following figure. Select the
equipment to be moved and click [Move Up/Move Down] to change the display order.
149
User Manual
12.5 Checkpoint history
Select [Checkpoint History] in the access management interface to display the
[Checkpoint History] list, as shown in the following figure.
Explain：
In the bayonet history interface, the access area, license plate number and access time can be
searched and queried.
12.5.1 Access area
In the [Checkpoint History] list, select one of them and click the [View] button to view
the current vehicle access area, as shown in the following figure.
150
User Manual
151
User Manual
13 Electronic Map
Operation function and management of electronic map.
13.1 Electronic Map configuration
13.1.1 Add map
Click the [Add Map] button, as shown in the following figure, enter the map name and
select the map picture path, click [OK] to save the current map, and click [Cancel] to
close the current interface.
13.1.2 Delete map
Select the electronic map to be deleted in the interface, click the [Delete Map] button,
and a prompt box of the deletion button will appear, as shown in the following figure.
Click [OK] to delete the electronic map, and click [Cancel] to close the prompt box and
cancel the deletion.
152
User Manual
13.1.3 Modify map
To modify the map name or map base picture, click the [Modify Map] button, as shown
in the following figure, click [OK] to save the current map, and click [Cancel] to close the
current interface.
13.1.4 Add / delete devices
Operation steps:
1. In the user-defined equipment list on the right side of the editing interface, select the
equipment to be added to the electronic map, and drag the mouse to the area where
the equipment needs to be added to complete the addition of the data acquisition
channel. Drag the " " channel device icon to change where you want to add it. When
an alarm occurs on this channel, the " " icon flashes with a red border.
2. Support to add two nodes of alarm input " " and alarm output " " in the
153
User Manual
electronic map. The input node will flicker when receiving the alarm of alarm input. The
alarm can be eliminated through the context menu [Eliminate alarm]. The alarm output
can be controlled to open and close the alarm output through the context menu [Open
alarm output/Close alarm output].
3. For devices that have been added, [Added] will be prompted in the custom device
list.
4. To delete the device, select and right click the [Delete Device] button in the figure, or
select the device to be deleted in the electronic map list on the left, and click the
[Delete Device] button above to delete the device on the current electronic map.
13.2 Configure heat zone
Operation steps:
1. Click the [Configure Hotspot] button to associate other electronic maps on the
current electronic map, as shown in the following figure.
2. Check the electronic map on the left and click the [Move In] button to add the
electronic map to the associated area on the right, as shown in the following figure.
3. Click the [Move Out] button to move the electronic map from the right associated
area back to the electronic map area.
154
User Manual
4. Click the [Confirm] button to display the "" hotspot icon on the current electronic
map, and drag it to reset the location of the hotspot.
5. Click the [Cancel] button to close the current interface.
Explain：
To delete the hotspot, select the hotspot button and right click Delete.
13.3 Electronic map preview
Operation steps:
1. Click the [Preview] button to preview the current electronic map.
2. Click the [Full Screen] button to view the preview interface in full screen.
3. Click the [Back] button to return to the previous preview operation.
Explain：
In the electronic map preview interface, it is supported to manually drag the picture or the
mouse wheel to change the display position of the picture or enlarge the picture of the position.
4. Double-click the device button on the map to open the device video preview, as
shown in the following figure.
155
User Manual
5. Right click the equipment icon to pop up the selection box to play the video, play
back the video and eliminate the alarm, as shown in the following figure. Select the
video playback to jump to the video playback interface.
156
User Manual
14 User management
Unified management of client users, add, delete, edit and configure permissions.
Explain：
The interface displays the basic information of all currently added users.
Only the Admin super administrator account has permission to enable this function.
14.1 Add user
Click Add in the User Management interface to pop up the Add User window, as
shown in the following figure.
157
User Manual
The interface parameters are described as follows:
Parameter Instruction
User level Set administrator or operator for current system.
User name Users to fill in any name.
【 Note 】 There ’ s illegal character limit when adding user name,
following characters are not allowed to be input
~!#$%^()=[]{},":;'<>?*`+/\&.
Password To set password for newly added user.
Confirm password Needs to be the same as input "Password".
Validity Set the expire date of the authority for users.
Description Supplement and describe user information.
User authority Set the user authority of administrator or operator, such as the
authority of video browsing, audio preview authority ,PTZ control,
video playback, video download, system lock, system delock,
intercom, alarm check, etc.
Permissions Set devices permit user authority to apply.
Explain：
The audio preview permission is mainly used to control all audio opening operations in the
platform.
The audio preview permission, PTZ control permission, video playback permission, and video
download permission depend on the video preview permission. If you want to open any one of the
audio preview permission, PTZ control permission, video playback permission, and video download
158
User Manual
permission of a channel, you must open the video preview permission first;
The intercom permission depends on the audio permission. Only when at least one channel
under the host has enabled the audio permission, can the intercom permission of the host be
enabled.
14.2 Edit user
Select the user to be edited in [User List], and click [Edit] to pop up the [Modify
User] window, as shown in the following figure.
Notice：
The related information of the user can be modified in the editing interface, including user level,
user name, validity period, password, description, user authority and authority configuration.
Admin Super Admin user can only modify the password.
159
User Manual
14.3 Delete user
Select the user to be deleted in User List, click Delete to pop up a prompt box, click
OK to delete the selected user, and click Cancel to cancel the deletion, as shown in the
following figure.
Notice：
You can delete multiple users at the same time. The superuser admin cannot be deleted.
160
User Manual
15 Intelligent search
Retrieve the received Intelligent information.
15.1 Face retrieval
Premise:
1. The device channel has a storage medium and is configured with a face detection
algorithm.
2. Enable the smart application image collection function in the client [System
Settings-Smart Application].
Operation steps:
1. After entering the [Intelligent Retrieval] interface, select [Face Retrieval] in the
rightmost display bar, and the relevant functions and contents will be displayed in the
left area, as shown in the figure.
2. The user can select any channel in the monitoring point on the left, set the query
conditions, and click the [Search] button to query the detailed information of all the
161
User Manual
records of the monitoring point in the time period. Two display forms, list and chart,
are supported.
3. Click [List] to display the search results in the form of a list, including the snapshot
time, channel name, gender, age, whether to wear a mask, whether to wear glasses and
body temperature. Click [Details] to see the detailed information of the snapshot, as
shown in the following figure. Click [Playback] to see the playback video.
4. Click [Figure] to display the search results in the form of a chart. You can view the
details and playback information of the captured pictures, as shown in the following
figure.
162
User Manual
5. Select any piece of data in the search results and click the [Export] button to
download the data results to the local. The export results are shown in the following
figure.
6. Click the [Export All] button to export all the search results.
15.2 Behavior analysis and retrieval
Premise:
1. The NVR device has a storage medium, and the device channel is configured with a
behavior analysis algorithm.
2. Enable the smart application image collection function in the client [System
Settings-Smart Application].
3. This function supports NVR devices and queries up to 32 channels at the same time.
Operation steps:
The user can select the equipment supporting the algorithm in the monitoring point on
the left, set the query conditions, and click the [Search] button to query the detailed
information of all records of the monitoring point in the time period, including the
alarm time, channel name, alarm type, etc., as shown in the following figure.
163
User Manual
The interface parameters are described as follows:
Parameter Instruction
Start Time The start time of query behavior analysis alarm can be set.
End Time End time of query behavior analysis alarm can be set.
Types of behavior analysis can be selected, including tripwire,
Behaviors Type double tripwire, perimeter, wandering, parking, running, stolen
items, and items left behind.
Retrieve Click to display the search results.
Select any piece of data in the search results and click the button
Export
to download the data to the local.
Select All Click to select all search results.
Select all search results except those in the currently selected
Reverse election
range.
164
User Manual
Details Click to see the snapshot details of the search results.
Click to see the playback video of the retrieval result. If there is no
Playback
video, the real-time preview screen of the channel will be played.
165
User Manual
16 Data statistics
Face data, passenger flow data and heat map are counted, and the total amount,
proportion and trend of data are displayed through statistical charts and lists.
16.1 Face statistics
Premise:
1. Device has a storage medium and is configure with a face detection algorithm.
2. Enable the smart application image collection function in the client [System
Settings-Smart Application].
Operation steps:
After entering the data statistics interface, select [Face Statistics] in the leftmost
column to display the relevant contents and functions in the right sidebar.
Explain：
Face statistics support statistics according to age, gender, number of people, whether wearing
166
User Manual
glasses, whether wearing masks, and abnormal body temperature.
16.1.1 Statistics by age group
Operation steps:
1. In the [Face Statistics] function interface, select [Statistics Type-> Age] at the top of
the left column to perform statistics according to age, as shown in the following figure.
Explain：
Face statistics can be divided into four age groups: youth, youth, middle age and old age.
2. The platform supports list display and chart display, as shown in the following
figure.
167
User Manual
16.1.2 Statistics by gender
Operation steps:
1. In the [Face Statistics] function interface, select [Statistics Type-> By Gender] at the
top of the left column to perform statistics according to gender, as shown in the
following figure.
168
User Manual
Explain：
[Unknown] Displays [Unknown] when a human form is detected for the device but no face is
detected.
Face statistics can be divided into male, female and unknown according to gender statistics.
2. The platform supports list display and chart display, as shown in the following
figure.
169
User Manual
16.1.3 Statistics by the number of people
Operation steps:
1. In the [Face Statistics] function interface, select [Statistics Type-> By Number of
People] at the top of the left column to perform statistics according to the number of
people, as shown in the following figure.
170
User Manual
2. Face statistics counts the number of people per hour according to time. The platform
supports list display and chart display. In the graphic interface, click " " to switch to
line chart display, and click " " to switch to histogram display, as shown in the
following figure.
171
User Manual
16.1.4 Statistics by whether wearing glasses
Operation steps:
1. In the [Face Statistics] function interface, select [Statistics Type-> Wear Glasses] at
the top of the left column to perform statistics according to the number of people, as
shown in the following figure.
172
User Manual
Explain：
Face statistics are based on whether the inspector wears glasses or not, which can be divided
into two kinds of display: without glasses and with glasses.
2. The platform supports list display and chart display, as shown in the following
figure.
173
User Manual
16.1.5 Statistics by whether wearing mask
Operation steps:
1. In the [Face Statistics] function interface, select [Statistics Type-> Wear Masks] at the
top of the left column to perform statistics according to the number of people, as
shown in the following figure.
2. The platform supports list display and chart display, as shown in the following
figure.
174
User Manual
16.1.6 Statistics by body temperature measurement
Operation steps:
1. After selecting [Statistics Type-> Abnormal Body Temperature] in the [Face Statistics]
function interface, statistics can be made according to the number of people, as shown
in the following figure.
175
User Manual
Explain：
Face statistics counts the number of people with abnormal body temperature per hour
according to time.
2. The platform supports list display and chart display, as shown in the following
figure.
176
User Manual
16.2 Visitor flow statistics
Premise:
1. The device has a storage medium and is configured with a headcount algorithm.
2. Turn on the picture receiving function in the client [System Settings-Smart
Application].
Select [Passenger Flow Statistics] in the [Data Statistics] interface to display its
relevant contents and functions. Passenger flow statistics supports real-time statistics
and report statistics. Real-time statistics can monitor the passenger flow in real time
according to the set area, and alarm when the number of people increases too much.
The report statistics can count the number of people entering, leaving and passing
according to the set area, and display it in the form of list or graph, as shown in the
following figure.
177
User Manual
16.2.1 Real-time Statistics Device List
Operation steps:
1. After entering the [Data Statistics] interface, select [Real-time Statistics] in the
middle column, expand [Equipment List] below to enter the equipment list column,
enter key information in the search box, and double-click to locate the passenger flow
equipment, as shown in the following figure.
2. Select the equipment in the list of passenger flow equipment and right click to pop
up the right-click menu of the list of passenger flow equipment, as shown in the
following figure.
3. Select [Analysis Configuration] to enter the configuration tool interface to view the
current configuration of each channel, as shown in the following figure.
178
User Manual
The interface parameters are described as follows:
Parameter Instruction
Analysis channel name Switch channels and analyse the configuration of each channel.
Read the algorithm supported by the front-end device and draw it in
Mode
the right video frame or directly in the video frame.
Sample Display the effect sketch shown in the video box.
Display the maximum size of the target, and the range can be set from
Max. Size of the target
6% to 30%
Display the minimum size of the target, and the range can be set from
Min. Size of the target
5% to 20%
Set the detection sensitivity. The higher the sensitivity, the more
Sensitivity
sensitive it is. The range can be set from 0 to 100.
Video frame Display the video and its algorithm under the channel.
179
User Manual
Hide prompt Hide the prompts in the configuration information on the left.
Redraw the statistical area in the video graph.
Redraw the statistical lines in the video graph.
Eliminate the lines.
Analysis channel name Switch channels and analyse the configuration of each channel.
4. Click [Add Device] in the device list to enter the passenger flow camera configuration
interface, as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
In the left device list, select the device or device channel. In the right
Import guest flow camera list, select a group, and click to add the device or
device channel to the guest flow camera group.
In the right guest flow camera list, select a group or device channel,
Export and click to delete the group and its device channel or device channel
from the guest flow camera list.
180
User Manual
In the right guest flow camera list, select the node and click to add the
Add Group
guest flow group.
In the right guest flow camera list, select a group and click to delete
Delete Group
the guest flow group.
In the right guest flow camera list, select the node and click to modify
Modify Group
the guest flow group name.
16.2.2 Real-time Statistics Area List
Operation steps:
1. After entering the [Data Statistics] interface, select [Real-time Statistics] in the
middle column, and expand [Area List] at the bottom to enter the equipment list
column. After entering the area list, you can switch the area scene, as shown in the
following figure.
2. In the area list, click “ ” to delete established area.
3. Click “ ” to update the configuration information of present area
4. Click “Add area” to enter the area configuration page to set information of area
detection time, capacity, number of people surge, whether or not to enable alarm,
detection device channel, etc, as is shown in below figure
181
User Manual
The interface parameters are described as follows:
Parameter Instruction
Set the name of the detection area to facilitate the rapid positioning
Area name
of the area.
Start time/End time Set the time of starting and finishing of statistics.
People capacity Set the upper limit of the capacity. This is required.
Rapidly increased number Set the upper limit of the increase of the number of people in the unit
of people time (10 minutes, 30 minutes, 1 hour, 2 hours). This is a required field.
Alarm interval Set alarm interval, supporting 10, 20, 30, 40, 50, 60 minutes.
Number of people staying Set the current number of existing people.
Set the detected channel video to be detected. Multiple channel
Add
videos adding is possible.
182
User Manual
Select the channel video to be deleted. Multiple channel videos
Delete
deletion is possible.
16.2.3 Real-time Data of Real-time Statistics
Select the area to be viewed in the area list, and the configuration information of
the area can be viewed at the bottom of the interface, as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
Recount Click to eliminate the recorded number of people.
Peak Record the maximum number of people in current area.
Record the number of people at current time. If the number exceeds
Current number of people the one that can be accommodated, it will turn into a red box;
otherwise, it will be a green box.
Record the number of people in three status namely entering / leaving
Enter/Leave/Passing / passing by. At the same time, the color of each case is distinguished.
Red colour represents entering, green leaving, and blue passing by.
The number of people is displayed in real time according to minutes.
Real-time Line Chart Red represents entering, green represents leaving, and blue
represents passing.
183
User Manual
Capture, capture picture save path can be changed from [system
settings] > [common settings] > [path settings].
Start all videos. The video download and save path can be changed
from system Settings > Common Settings > Path Settings.
Set the number of pictures, supporting picture display amount 1, 4, 9,
36, 49, 64.
Full screen, full screen display of video page and real-time data page.
Click again to cancel the full screen.
16.2.4 Video Page of Real-time Statistics
View the video effect of real-time preview in video page, as is shown in below figure:
Explain：
See the [Video Preview] window for relevant Parameters of the interface.
16.2.5 Report statistics
Operation steps:
1. Count the number of people in a selected area in the report statistics interface. It
supports the statistics of the number of people entering, leaving, and passing by
184
User Manual
according to detailed time, as shown in the following figure.
2. Select the report type and statistics time. If you want to make statistics by detailed
time, enable the Detailed Time check box. During statistics, the number of people in the
detailed time period will be displayed. Click Export to export the statistics data to the
local machine, as shown in the following figure.
185
User Manual
3. Data can be displayed in list form and graph form. Graph form supports line chart
and column chart, as shown in the following figure.
16.3 Heat map statistics
Premise:
186
User Manual
1. The device has a storage medium and is configured with a behavior analysis-heat
map statistical algorithm.
2. Turn on the picture receiving function in the client [System Settings-Smart
Application].
Operation steps:
After entering the data statistics interface, select [Heat Chart Statistics] in the
leftmost column, and select the corresponding equipment in the equipment list to
display its related contents and functions in the right sidebar, as shown in the following
figure.
Explain：
Heat map is to show the distribution of people in each part of the screen with the color of heat.
A detection area is set to detect the active information of personnel in the specified area. Through
the heat chart report, the personnel distribution can be visually presented in terms of time or space.
187
User Manual
188
User Manual
17 Alarm configuration
Configure linkage for various types of alarms.
17.1 Alarm configuration of Monitoring point
Operation steps:
1. After entering the [Alarm Configuration] interface, expand [Monitoring Point] in the
left column to perform the operation of monitoring point alarm configuration, as
shown in the following figure.
2. Select the channel to set the alarm at the monitoring point on the left, and the alarm
type supported by the monitoring point will be displayed, as shown in the following
figure.
189
User Manual
3. Click [Alarm Level Setting] to modify the alarm level. The alarm level is divided into
emergency, high level, medium level and low level. The alarm types in different level
boxes can be dragged to other levels, as shown in the following figure.
4. Uncheck or check the alarm level to filter different alarm levels, as shown in the
following figure.
190
User Manual
5. Uncheck or check the alarm level to filter different alarm levels, as shown in the
following figure.
6. After the channel and alarm type are selected, the alarm linkage can be configured,
as shown in the following figure.
17.1.1 Linkage notification
Operation steps:
1. Enable alarm linkage. Alarm linkage is a general configuration item. If it is not
enabled, even if notification and linkage video are configured, alarm linkage will not
191
User Manual
take effect.
2. Enable automatic saving of alarm pictures. Before enabling this function, it is
necessary to ensure that the equipment alarm linkage is configured with linkage
snapshot, and the client has enabled the function of collecting pictures in [System
Settings-Intelligent Applications].
3. After the alarm sound is turned on, when an alarm occurs, the computer where the
client is installed will play the alarm sound. You can use the default sound or upload the
voice by yourself.
4. After the bubble prompt is turned on, when an alarm occurs, the client will pop up
an alarm prompt box in the lower right corner.
5. After sending mails is enabled, when an alarm occurs, an alarm mail will be sent to
the set receiving mailbox. The configuration is shown in the following figure.
192
User Manual
The interface parameters are described as follows:
Parameter Instruction
SMTP service Configure the E-mail server address.
Port Manually fill in the server port.
Encrypton method Point encryption methods, including SSL and TSL.
User name Configure sender E-mail name.
Authorization code Configure sender E-mail authorization code.
theme Manually fill in the subject of the message.
Receiver Configure the recipient E-mail address.
CC Configure the CC mailbox address.
17.1.2 Linking video
After setting the linkage notification, click Next to set the linkage video.
193
User Manual
Linkage video means that when an alarm occurs, the real-time video screen of the
configured channel will pop up, as shown in the following figure.
Linkage video recording means that when an alarm occurs, the configured channel will
record the video, and the video recording duration can be set.
17.1.3 Linkage alarm output
After setting the linkage video, click Next to set the linkage alarm output. This function
can only be used after the open linkage is checked. Linkage alarm output requires that
the equipment supports alarm output and has an alarm output port. The equipment
can realize the specific alarm function through the external alarm. The IPC generates an
alarm and transmits the signal to the alarm, and then the alarm takes effect. Commonly
used alarms, such as external alarm lights, alarm bells, buzzers and other equipment,
are connected to the ALARM OUT interface of the equipment. The signal type is divided
into open and close, that is, the open and close of the line, as shown in the following
194
User Manual
figure.
17.1.4 Linkage deployment time
After setting the linkage alarm output, click Next to enter the linkage defense time
configuration, and configure the effective time for the linkage mode, as shown in the
following figure.
195
User Manual
Click the [Copy to] button in the upper right corner of the linkage deployment time to
copy the set linkage mode to other channels, as shown in the figure below.
196
User Manual
17.2 Alarm configuration of device
Operation steps:
The alarm types supported by the device are shown in the following figure, and the
specific operation is the same as the 16.1 monitoring point alarm configuration.
197
User Manual
17.3 Alarm configuration of People counting area
Operation steps:
The alarm types supported by the passenger flow area are shown in the following
figure, and the specific operation is the same as the alarm configuration at the 16.1
monitoring point.
198
User Manual
18 Operation logs
Query the operation log of the system to understand the usage of the system, as shown
in the following figure.
Explain：
Support query of login log, operation log and configuration log.
The interface parameters are described as follows:
Parameter Instruction
Starting time Available to set the starting time of log query.
Ending time Available to set the ending time of log query.
User name Available to query the operation record of one user. Admin-super
administrator user may check the operation record of all users.
Log Type Available to query logs by type, including all, login, operation and
configuration.
199
User Manual
Detail Type Available to conduct detailed classified query of all, login, operation
and configuration by type.
Log description Search key word to query log information.
Export Logs Click Export Logs, available to output and save logs.
Query Click Query, available to query logs according to query conditions.
Reset Click Reset, to restore query conditions to default status.
Total X Pages Display how many pages does the query result has.
To X Page Select a page to jump to the log record on that page.
200
User Manual
19 Video player
Play the local playback video, as shown in the following figure.
The interface parameters are described as follows:
Parameter Instruction
Local video can be selected for playback.
Step button. Click it to play the video file frame by frame, but the
/
player does not support this function.
Slow button. Click it to slow down the video file.
/ Play/Pause button, click to control the start/pause of the video file.
Stop button, click to stop the current video file playback.
Fast-play button, click to fast-play the video file.
You can adjust the playback speed of the video. The available
playback speeds are 1/16 X, 1/8 X, 1/4 X, 1/2 X, 1x, 2 X, 4 X, 8 X, 16x.
201
User Manual
Full Screen button. Click it to display the playback window in full
screen. Press the ESC key to turn off the full screen.
Volume adjustment bar. Drag to adjust the volume of video playback
sound. Tap the speaker to turn the sound on/off.
Click to view recently viewed video files.
/ Zoom in/out on the current player interface.
Close the player.
202
You might also like
- Dahua CyberCity - User's Manual - V1.3.0No ratings yetDahua CyberCity - User's Manual - V1.3.0186 pages
- DMC8000 Video Wall Controller User Manual-V1.00No ratings yetDMC8000 Video Wall Controller User Manual-V1.0017 pages
- UD09493B Baseline User Manual of iDS-96 6700NXI-I 4F Network Video Recorder V4.1.10 20180316No ratings yetUD09493B Baseline User Manual of iDS-96 6700NXI-I 4F Network Video Recorder V4.1.10 20180316208 pages
- Uniarch Network Video Recorders User Manual-V1.00No ratings yetUniarch Network Video Recorders User Manual-V1.0099 pages
- Network Video Recorders User Manual-V1.17No ratings yetNetwork Video Recorders User Manual-V1.17170 pages
- REVO Ultra L-Series IP Camera User Manual - V1.01 (181023)No ratings yetREVO Ultra L-Series IP Camera User Manual - V1.01 (181023)42 pages
- Easy7 Smart Client Express For Windows V8.5No ratings yetEasy7 Smart Client Express For Windows V8.5159 pages
- DSS7016D-S2 Users-Manual V8.2.0 20230423 ENNo ratings yetDSS7016D-S2 Users-Manual V8.2.0 20230423 EN277 pages
- Network Video Recorder Series Quick Start Guide V1.1No ratings yetNetwork Video Recorder Series Quick Start Guide V1.149 pages
- Galaxy Pro Series 4MP VF IR Dome Camera - 2.8 12mm User Manual-V1.05No ratings yetGalaxy Pro Series 4MP VF IR Dome Camera - 2.8 12mm User Manual-V1.05125 pages
- Network Video Recorders User Manual-V1.14No ratings yetNetwork Video Recorders User Manual-V1.14147 pages
- Network Video Recorder - Quick Start Guide - V1.0.0No ratings yetNetwork Video Recorder - Quick Start Guide - V1.0.028 pages
- Manual de Usuario para Serie DS-96000NI-INo ratings yetManual de Usuario para Serie DS-96000NI-I188 pages
- UD12787B - Baseline - User Manual of DS 96000NI I Series Network Video Recorder - 20230303No ratings yetUD12787B - Baseline - User Manual of DS 96000NI I Series Network Video Recorder - 20230303193 pages
- Safire - User Manual of Truesense Network Video RecorderNo ratings yetSafire - User Manual of Truesense Network Video Recorder175 pages
- Embedded+Multi-Screen+Controller User's+Manual V2.0.0No ratings yetEmbedded+Multi-Screen+Controller User's+Manual V2.0.0100 pages
- Dahua-DSS-Express - User-Manual - V8 6 0 1No ratings yetDahua-DSS-Express - User-Manual - V8 6 0 1278 pages
- DSS General Surveillance Management Center: User 'S ManualNo ratings yetDSS General Surveillance Management Center: User 'S Manual203 pages
- Digital Video Recorder Quick Start Guide V1.0.0-EngNo ratings yetDigital Video Recorder Quick Start Guide V1.0.0-Eng37 pages
- IP Indoor Monitor - Quick Start Guide - V1.0.0-EngNo ratings yetIP Indoor Monitor - Quick Start Guide - V1.0.0-Eng31 pages
- EYEONET DVR User Manual - 1.3.5 VersionNo ratings yetEYEONET DVR User Manual - 1.3.5 Version133 pages
- DSS-Express Users-Manual V8.4.0 20240117No ratings yetDSS-Express Users-Manual V8.4.0 20240117242 pages
- Network Video Recorder - Quick Start Guide - V1.0.0-EngNo ratings yetNetwork Video Recorder - Quick Start Guide - V1.0.0-Eng33 pages
- Computerised Systems Architecture: An embedded systems approachFrom EverandComputerised Systems Architecture: An embedded systems approachNo ratings yet
- SIMATIC Process Control System PCS 7 SIMATIC Route Control V7.1 Rchelp - B - en-USNo ratings yetSIMATIC Process Control System PCS 7 SIMATIC Route Control V7.1 Rchelp - B - en-US686 pages
- X230 Series: Command Reference For Alliedware Plus™ Version 5.4.6-1.XNo ratings yetX230 Series: Command Reference For Alliedware Plus™ Version 5.4.6-1.X1,851 pages
- Performance Benchmarks For ODBC vs. Oracle, MySql, SQL Server PDFNo ratings yetPerformance Benchmarks For ODBC vs. Oracle, MySql, SQL Server PDF3 pages
- "Mini Project Title": A Mini Project Report Submitted To University of Pune, PuneNo ratings yet"Mini Project Title": A Mini Project Report Submitted To University of Pune, Pune16 pages
- PROGRAMMING PARADIGMS Categories of Programming Paradigms TheNo ratings yetPROGRAMMING PARADIGMS Categories of Programming Paradigms The17 pages
- Getting Started With ABAP Cloud DevelopmentNo ratings yetGetting Started With ABAP Cloud Development15 pages
- Solutions Manual To Irodov General Problems in Physics - Mechanics - Problems From 76 To 100No ratings yetSolutions Manual To Irodov General Problems in Physics - Mechanics - Problems From 76 To 10030 pages
- Create New SKEY For Isometric Drawing in PDMS DRAFT - PDMSidNo ratings yetCreate New SKEY For Isometric Drawing in PDMS DRAFT - PDMSid13 pages
- How To Customize Linux Terminal With OH MY ZSH (2023)No ratings yetHow To Customize Linux Terminal With OH MY ZSH (2023)1 page
- Salwico GS5000 - Configuration Manual - M - EN - 2015 - DNo ratings yetSalwico GS5000 - Configuration Manual - M - EN - 2015 - D50 pages
- A Consultancy Project On Master Tiles & Ceramic Industries LTD SUBMITTED TO: Sir Salman Khan MangolNo ratings yetA Consultancy Project On Master Tiles & Ceramic Industries LTD SUBMITTED TO: Sir Salman Khan Mangol68 pages
- SIEMonster V4 Starter Edition Operations Guide V1.0100% (1)SIEMonster V4 Starter Edition Operations Guide V1.0210 pages
