a product of MVTec

Extension Package
Programmer’s Manual

HALCON 24.11 Progress-Steady

This manual shows how to create HALCON extension packages based on new operators written in C, Version 24.11.1.0.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Copyright © 1997-2024 by MVTec Software GmbH, Munich, Germany

Protected by the following patents: US 7,239,929, US 7,751,625, US 7,953,290, US 7,953,291, US 8,260,059, US 8,379,014,
US 8,830,229, US 11,328,478. Further patents pending.
OpenCL™ and the OpenCL logo are trademarks of Apple Inc. used by permission by Khronos.
OpenGL® and the oval logo are either trademarks or registered trademarks of Hewlett Packard Enterprise in the United States
and/or other countries worldwide.
Linux ® is a registered trademark of Linus Torvalds.
Microsoft, Windows, Microsoft .NET, Visual C++ and Visual Basic are either trademarks or registered trademarks of Microsoft
Corporation.
Sun is a trademark of Oracle Corporation.
UNIX® is a registered trademark of The Open Group.
All other nationally and internationally recognized trademarks and tradenames are hereby recognized.

More information about HALCON can be found at: http://www.halcon.com

About This Manual

This manual describes how to extend HALCON by additional operators encapsulated in HALCON packages us-
ing the Extension Package Interface. Before starting to use the Extension Package Interface, MVTec strongly
recommends that the user should be familiar with the normal HALCON system.
This manual is written for the expert HALCON user who wants to extend the system for specific requirements.
Thus, the reader should be familiar with the normal HALCON system. Furthermore, programming skills are
required. Finally, the reader should know about his/her development environment (that is how to invoke the
compiler/linker etc.).
This manual is divided into the following parts:
• Introduction
This chapter provides a short overview of HALCON packages and their creation. Furthermore, an example
showing the integration of a simple operator is presented.
• Operator Description (DEF file)
This chapter summarizes the minimum required operator description used by the HALCON compiler hcomp
as well as the complete operator description which is needed to provide a full integration of new operators in
HDevelop and to generate documentation files.
• Style Guide for Programming
This chapter introduces basic style guides for how to program HALCON operators. Especially, the HALCON
memory management is explained.
• HALCON Data Types
In this chapter the most important HALCON data structures to handle iconic data and control parameters are
presented.
• Handling Iconic Objects and Control Parameters
This chapters contains a set of routines to facilitate the programming of the operator interface and accessing
the basic HALCON data structures.
• Special Routines for Typical Supply Procedures
This chapter describes a set of convenience routines for standard situations.
• Creating a New HALCON Package
The last chapter explains how to use the HALCON compiler hcomp to generate HALCON packages for
different platforms.

Symbols

The following symbol is used within the manual:

! This symbol indicates an information you should pay attention to.

Contents

1 Introduction 9
1.1 HALCON Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1.1 Using HALCON Operators in C, C++, and .NET Languages . . . . . . . . . . . . . . . . 10
1.1.2 Internal Structure of HALCON Operators . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2 HALCON Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2.1 Packages and HALCON XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2.2 Directory Structure of a HALCON Package . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2.3 How to Create and Use a HALCON Package . . . . . . . . . . . . . . . . . . . . . . . . 13
1.3 Installing a HALCON Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.3.1 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.3.2 Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.4 An Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2 Operator Description (DEF File) 19

2.1 Short Operator Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.2 Extended Operator Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.2.1 Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.2.2 short . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.2.3 warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.2.4 abstract . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.2.5 module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.2.6 chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.2.7 functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.2.8 keywords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.2.9 predecessor, successor, alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.2.10 see_also . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.2.11 attention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.2.12 result_state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.2.13 parallelization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.2.14 complexity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.2.15 example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.2.16 references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.2.17 class Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.3 Describing the Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.3.1 Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.3.2 default_type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.3.3 sem_type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.3.4 modified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.3.5 multivalue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.3.6 costs_weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.3.7 postprocessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.3.8 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.3.9 type_list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.3.10 default_value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.3.11 values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.3.12 value_list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.3.13 value_min, value_max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
 2.3.14 step_rec, step_min, value_function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.3.15 value_number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.3.16 assertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.3.17 multichannel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.3.18 multiinstance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.3.19 file_ext, file_ext_descr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.4 Text in DEF Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.5 Chapter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

3 Style Guide for Programming 39

3.1 Basic Numeric Data Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.1.1 Attributes of Iconic Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.1.2 Local Variables / Temporary Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3.1.3 Procedure Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3.1.4 Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3.2 Memory Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.2.1 Temporary Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.2.2 Global Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.2.3 Debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.3 Structuring Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.4 Extension Package Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.5 Name Conventions for Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.6 Input / Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.7 Error Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.7.1 Defining Own Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.7.2 Extending Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.8 Notes on Image Processing Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4 HALCON Data Types 49

4.1 Pixel Data (Himage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.2 Region Data (Hrlregion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.3 XLDs (Hcont, Hpoly) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.4 Control Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

5 Handling Iconic Objects and Control Parameters 57

5.1 Basic Access to Iconic Input Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.1.1 HGetObj . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.1.2 HGetComp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
5.1.3 HGetRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
5.1.4 HGetImage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5.1.5 HGetXLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
5.2 Additional Routines for Accessing Input Image Objects . . . . . . . . . . . . . . . . . . . . . . . 62
5.2.1 HGetDRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
5.2.2 HGetFDRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
5.2.3 HGetURL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.2.4 HGetDImage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
5.2.5 HGetObjNum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5.3 Loop Macros for Accessing Single Input Objects . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5.3.1 HAllObj . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.3.2 HAllComp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4 Creating Objects and Writing Output Object Parameters . . . . . . . . . . . . . . . . . . . . . . . 67
5.4.1 HCrObj . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.4.2 HCopyObj . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
5.4.3 HPutDRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.4.4 HPutImage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.4.5 HDefObj . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.4.6 HPutDImage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
5.4.7 HCrImage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
5.4.8 HCrXLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5.5 Reading and Writing Control Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
 5.5.1 HGetPElemX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
5.5.2 HGetPPar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
5.5.3 HGetPElem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
5.5.4 HGetCElemX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.5.5 HGetElemX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.5.6 HCopyElemX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
5.5.7 HGetCPar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
5.5.8 HGetSPar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
5.5.9 HGetCParNum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
5.5.10 HAllocStringMem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5.5.11 HPutPElem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.5.12 HPutPPar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.5.13 HPutElem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
5.5.14 HPutElemH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
5.5.15 HPutCPar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
5.6 Auxiliary Extension Package Interface Macros and Procedures . . . . . . . . . . . . . . . . . . . 82
5.6.1 HCkP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.6.2 HCkNoObj . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.6.3 HRLDecomp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.6.4 HNumOfChannels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
5.6.5 HIncrRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

6 Special Routines for Typical Supply Procedures 87

6.1 Loop Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.1.1 HAllReg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.1.2 HAllSegm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.1.3 HAllFilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
6.1.4 HAllFilter2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.2 Object Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.2.1 HNewRegion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
6.2.2 HPutRect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
6.2.3 HDupObj . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

7 Creating a New HALCON Package 97

7.1 The HALCON Compiler ’hcomp’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7.1.1 Selection of the Host Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7.1.2 Creating the Help Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
7.1.3 Creating HTML Reference Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
7.1.4 Creating the PDF Reference Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
7.1.5 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
7.2 Generating HALCON Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
7.2.1 Creating the Operator Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
7.2.2 Creating the C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
7.2.3 Creating the C++ Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
7.2.4 Creating the .NET Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
7.2.5 Creating New Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
7.2.6 Additional Information for Specific Platforms . . . . . . . . . . . . . . . . . . . . . . . . 101
7.3 HALCON Directories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

A HALCON Error Codes 105

B HALCON Semantic Types 141

Index 143
 Introduction 9

Introduction
Chapter 1

Introduction

HALCON can be extended by up to 99 additional operator packages. During the initialization of the system,
all packages indicated by the environment variable HALCONEXTENSIONS are automatically loaded. A package
typically contains libraries with the new operators, their prototypes, the operator information needed by HDevelop,
and the HTML online documentation. For the programming of such a package, the HALCON Extension Package
Interface is used, e.g., to manipulate parameters of HALCON operators and to read or write iconic data (images,
regions, XLDs1 ) from the HALCON database of iconic objects.
Furthermore, the operators provided by HALCON itself are also based on the functionality of the Extension Pack-
age Interface. Thus, the Extension Package Interface is both the interface between application programs and the
operator layer of the HALCON system and the interface between the operator layer and the iconic object database.
A reason why to extend the capabilities of HALCON by using the Extension Package Interface might be one of
the following:
• Extension of the pool of image processing operators,
• Integration of special image processing hardware,
• Integration of a special graphics software package.
The new extension package example program is an Easy Extension Interface example for .NET, and shows how to
easily integrate a .NET function, based on the HALCON/.NET interface, to HALCON’s operator set. It can be used
within HDevEngine and HDevelop. For more information, see the README.md in the Easy Extension Interface
for .NET example under %HALCONEXAMPLES%\extension_package\easy_extensions\dotnet. Once the users have
extended HALCON by a package containing their own operators, these can be used within all supported host
languages and the interactive tool HDevelop.
This chapter gives a short introduction to HALCON packages and operators, including an example describing the
integration of a simple operator. The following chapters present detailed information that will allow you to write
your own packages. As a common example, a package called halconuser will be used (see %HALCONEXAMPLES%\
extension_package\halconuser).
Except for Linux-specific sections, file paths and environment variables are printed in the Windows convention in
this manual, e.g.,
%HALCONEXAMPLES%\extension_package\halconuser
to denote the subdirectory halconuser containing an example package within the HALCON base directory ref-
erenced by the environment variable HALCONEXAMPLES. The same expression in Linux convention would look
like
$HALCONEXAMPLES/extension_package/halconuser

1.1 HALCON Operators

This section describes the external interface of HALCON operators, i.e., how to use them in a programming
language, and their internal structure.
1 eXtended Line Description; i.e., subpixel contours and polygons.
10 Introduction

1.1.1 Using HALCON Operators in C, C++, and .NET Languages

There are two different modes of calling operators from HALCON/C: One way is to call operators for simple
applications with only one value per control parameter (simple mode). This is the easiest way and sufficient
for many applications. When using complex procedures that need more than one value per parameter, data is
transferred within tuples (Htuple). Iconic objects are represented with the type Hobject, so that one object can
contain several images, regions, or XLDs.
In contrast, the HALCON/C++ and the HALCON/.NET interface support a flexible management of several types.
However, the defined class hierarchy has a fixed mapping between the HALCON operators and the provided
classes. This mapping follows predefined rules and is therefore partly generic. A user-defined HALCON operator
cannot be linked to an arbitrary position inside the class hierarchy. Thus, these operators are integrated using the
generic data type Hobject in order to pass arguments to and from the operator. This kind of integration is also
used, e.g., if you export your HDevelop program as C++ or C# code.
For further information on using HALCON in programming languages please refer to the Programmer’s Guide.

1.1.2 Internal Structure of HALCON Operators

HALCON operators (like the new operators in halconuser) typically consist of two procedures: One procedure
– the supply procedure – receives the input data, tests its consistency, passes it to the processing action procedure
and returns the output data after the processing. If the input data contains any composed iconic objects, e.g., image
tuples, the supply procedure has to extract the single parts. An iconic object key can represent an unlimited number
of iconic objects and every image object may consist of several components (one region and an unlimited number
of gray value channels; see also figure 5.2 on page 58). Generally, a user may assume that a HALCON operator
is able to handle single iconic objects as well as composed objects (i.e., multivalue is set to optional; see
page 30) and that it can work on multi-channel images (i.e., multichannel is set to optional; see page 34). So,
the author of a new HALCON operator should implement appropriate mechanisms for extracting the needed data
from composed iconic objects (or multi-channel images) within the supply procedure. The name of this procedure
designates the internal C-procedure name specified in the DEF file (cf. section 2.1 on page 19 and section 2.2 on
page 20).
After preprocessing the input data, the action procedure is called within the supply procedure. This procedure
performs the specific image processing. In most cases the action procedure receives only the already extracted
single components (e.g., regions of type Hrlregion, channels of type Himage, or pointers to the raw image data)
and parameter values. The results are returned to the supply procedure where they are passed to the generated
interface that returns them to the calling system. Every supply procedure returns an error code of type Herror.
Thus, it is necessary to return an error code, which is H_MSG_TRUE if no error occurred.
Only one parameter (a so called procedure handle) is passed to a supply procedure. All other input data (iconic
objects and control values) is read and written with the help of this identifier. Moreover, it allows the unique identi-
fication of a HALCON operator call while running HALCON on parallel hardware. Instead of further parameters,
all in- and output to and from the supply procedure is done with the help of several (internal) buffers, as illustrated
in figure 1.1.
The buffer contains input data as well as output data. Control parameters (containing all kind of control values
like integers, floating-point values, strings or handles) are stored directly in the buffers, whereas all iconic data
(including images, regions and XLDs) are stored in the database and represented by an iconic object key. Iconic
data can be accessed with the help of database procedures by using these keys. The Extension Package Interface
provides special procedures and macros for reading and writing elements of the parameter buffer within the supply
procedure. Every parameter belongs to one of the four classes
• input iconic object
• output iconic object
• input control parameter
• output control parameter
that determines the name of the suitable procedures/macros (e.g.: HGetCPar is used to get an input control value).
To identify a specific parameter within a class, its number is passed to the procedure/macro. This is the number of
 1.2 HALCON Packages 11

Introduction
Application Programs
Input Output

HALCON
C / C++ / .NET Interface Database

Buffer Buffer

Control Iconic Control Iconic

Parameter Objects Parameter Objects

Supply Procedure

Action Procedure

Figure 1.1: Data flow within HALCON.

the parameter within the parameter-list of a HALCON operator counted for every parameter class (e.g.: to get the
value of the second input control parameter, the number 2 must be passed to HGetCPar).
The read-/write access on the buffer is done automatically by the generated interface. The code of this interface is
generated by the HALCON compiler hcomp (see page 16 and section 7.1 on page 97) from a so-called definition
file (DEF file). Any programmer of a new HALCON operator must provide such a definition file, which contains
all relevant information, e.g., concerning in- and output parameters: information about the parameter class (input-
/output,iconic object/control), about the parameter type, etc. The syntax and semantics of the definition file is
explained in chapter 2 on page 19.

1.2 HALCON Packages

Similar to the standard HALCON system a programmer has to provide (at least) two libraries (DLLs in Windows,
shared libraries in Linux environments) in order to extend HALCON by a new operator package (see chapter 7 on
page 97).

• A library containing the new operators (written in C). Most of this manual is about how to write such opera-
tors based on internal data structures / procedures of the HALCON system. This library has the same name
as the package itself, in our example halconuser.
• Libraries encapsulating the generated interface code (for C, C++, .NET). These libraries (i.e., the operator
library and one of the interface libraries) have to be used in new applications in order to provide the interface
of the new operators to the host language of your choice. Most of the work concerning these libraries is
done by the HALCON compiler hcomp, see section 7.1 on page 97 for details. In the example package these
libraries are called halconuserc, halconusercpp, and halconuserdotnet.

The names of all these libraries are derived from the name of the package itself: A package package contains the
libraries2 package, packagec, packagecpp, and packagedotnet.
2 This is true for the Windows version. For Linux, the prefix lib is added to the libraries, resulting in libpackage, libpackagec, and

libpackagecpp.
12 Introduction

1.2.1 Packages and HALCON XL

Extension packages can also be used in HALCON XL. Similar to the HALCON libraries, which exist in two ver-
sions (e.g., halcon.dll and halconxl.dll), you must provide separate versions of your package libraries to be
used together with HALCON XL. The names of these libraries must have the suffix xl; e.g., the HALCON XL ver-
sion of the example package halconuser consists of the libraries halconuserxl.dll, halconusercxl.dll, hal-
conusercppxl.dll, and halconuserxxl.dll (Windows), libhalconuserxl.so, libhalconusercxl.so,
and libhalconusercppxl.so (Linux), and halconuserdotnetxl.dll (.NET).
The HALCON XL version of the libraries is created analogously to the standard HALCON version with only small
differences. See section 7.2 on page 100 for details.

1.2.2 Directory Structure of a HALCON Package

A HALCON package resides in a directory with the same name as the package itself. In our example this is the
directory halconuser in %HALCONEXAMPLES%\extension_package. This directory must at least contain the
following subdirectories

• bin\%HALCONARCH%: For Windows, this subdirectory has to contain the DLLs package.dll, pack-
agec.dll, and packagecpp.dll, corresponding to the above libraries (and their HALCON XL versions).
We also recommend to place compiled example programs or additional utilities of a package in this subdi-
rectory.
• lib\%HALCONARCH%: In this subdirectory the libraries encapsulating the new operators (package) and
the corresponding C and C++ language interfaces (packagec, packagecpp) reside3 , together with their
HALCON XL versions. Note that neither the name of these libraries nor their position within the
package should be changed. Otherwise, the HALCON system cannot load the package. The environment
variable HALCONARCH is set during the installation of HALCON; it describes the platform HALCON is
running on. See the Installation Guide, section 1.4 on page 8, for details.
• bin\dotnet: This subdirectory has to contain the extension package’s .NET assembly packagedot-
net.dll (and its HALCON XL version, packagedotnetxl.dll).
• help: This subdirectory contains files with data for the online access to the knowledge base. They must
be generated and placed in this directory in order to use a package inside of HDevelop. Without these files
HDevelop cannot retrieve the information needed to access the operators of a package.

We also recommend providing additional subdirectories:

• def: In this directory the DEF file(s) with the description of the operators of a package should be placed.
• include: In this directory the generated include files containing the prototypes for the operators of a
package should be placed.
• doc: In this directory the documentation of the package should be placed (see also %HALCONROOT%\doc for
comparison). Especially, it is necessary to put the generated HTML files in doc\html\reference in order
to enjoy the online help from the operator window of HDevelop.
• examples: This directory might contain some typical example programs (e.g., HDevelop dev-files) demon-
strating the use of the new operators.
• images: If the provided examples need specific images, they should be placed in this directory. In that
case we recommend including the path to this subdirectory in the environment variable HALCONIMAGES
to allow access to these images without using an absolute file path in the programs.
3 For Linux systems the prefix lib has to be added to the libraries resulting in libpackage, libpackagec, and libpackagecpp
 1.2.3 How to Create and Use a HALCON Package 13

1.2.3 How to Create and Use a HALCON Package

In summary, the following steps are necessary to create a HALCON package with the name package integrating

Introduction
new operators into the HALCON system. As noted in section 1.2.1, to create a HALCON XL package, you must
create a second version of the libraries. A detailed description of the steps can be found in the referenced sections
of this manual:
1. Description of the new operator(s) in one or more DEF files (cf. chapter 2 on page 19). We recommend
placing these files in the package subdirectory def.
2. Creation of a library (called package) containing the supply procedures in C and the corresponding
action procedures (cf. chapters 3 to 6). This library has to be placed in the package subdirectory
lib/$HALCONARCH (Linux) or bin\%HALCONARCH% (Windows).
3. Creation of a library containing the language-dependent operator interfaces (packagec, packagecpp,
packagex, and packagedotnet) based on the DEF files with the help of hcomp (cf. section 7.1 on page
97). These libraries have to be placed in the subdirectory lib/$HALCONARCH (C, C++ under Linux) or
bin\%HALCONARCH% (C, C++ under Windows) or bin\dotnet of the package.
4. Generation of files for online access to the knowledge base with the help of hcomp. These files are used,
e.g., by HDevelop. They have to be placed in the subdirectory help of the package.
5. Generating the HTML reference files with the help of hcomp (optional). The generated files have to be
placed in the subdirectory doc\html\reference of the package.
6. Generating PDF manuals with the help of hcomp (optional).
7. Extension of the package list in the environment variable HALCONEXTENSIONS by the complete file path of
the new package, e.g.,

%HALCONEXAMPLES%\extension_package\halconuser

For some platforms, additional environment variables have to be modified; see section 1.3 and section 7.2.6
on page 101.
8. Linking of the generated libraries together with the HALCON library to the image analysis application (cf.
chapter 7 on page 97). For this, you have to modify additional environment variables, depending on the
operating system (see below). Please note that HDevelop is able to access the new operators dynamically
without linkage.

1.3 Installing a HALCON Package

To install a HALCON package you have to copy the package to your hard disk and add the complete path of the
package to the environment variable HALCONEXTENSIONS, e.g.,

%HALCONEXAMPLES%\extension_package\halconuser

Note that the delimiter between paths in an environment variable is a semicolon on Windows systems and a colon
on Linux systems. Never change the name of a package or the corresponding names of the libraries or DLLs
contained in a package. These names are encoded within the libraries/DLLs. If you change the names this !
information will not match any longer. Thus, the loader of the operating system will fail to open the dynamic
libraries. To use the new package within HDevelop, you have to restart the program. For generating a stand-alone
application using the package you have to link the C or C++ interface library, or reference the .NET assembly of
the package in the application code, see section 7.2 on page 100.
If the package contains images used, e.g., within example programs you might want to include the corresponding
directory (e.g., images within the package) in the environment variable HALCONIMAGES to access those images
without specifying a complete path.
Furthermore, you must modify additional environment variables in order to use your new package (see below).
14 Introduction

1.3.1 Additional Information for Windows

To be able to link the package DLL to your application program, the complete DLL file path of the new package,
e.g.,

%HALCONEXAMPLES%\extension_package\halconuser\bin\%HALCONARCH

has to be added to the environment variable PATH, see section 7.2.6.1 on page 101.
! Do not copy a package DLL into the Windows system directories, as it would be loaded twice in this case!
Note that you must extend the variable PATH also for .NET applications, even if you do not explicitly link the main
package library (package.dll): The referenced .NET assembly automatically loads this library.

1.3.2 Additional Information for Linux

On Linux systems you have to include the package library subdirectory lib/$HALCONARCH in the environment
variable LD_LIBRARY_PATH in order to use a package.
This has to be done in any case – regardless whether you plan to use a package within HDevelop only or you want
to create stand-alone applications.
For .NET applications, an alternative to setting LD_LIBRARY_PATH is described in the Programmer’s Guide in
section 12.2.3 on page 87.

1.4 An Example
The following example illustrates the steps described in section 1.2 on page 11. Assume, one wants to implement
a new operator named user_thresh to extract all pixels with a gray value larger than a threshold value specified
in an input parameter. The use of user_thresh within a C program is illustrated in figure 1.2; a more detailed
example is provided in %HALCONEXAMPLES%\extension_package\halconuser\source\testthreshold.c.

main()
{
Hobject Image,Region;
int Thresh;

read_image(&Image,"monkey");
Thresh = 100;
user_thresh(Image,&Region,Thresh);
}

Figure 1.2: Calling the operator user_thresh in C.

To use user_thresh in this way within C programs4 ,

• The new operator must be implemented.

• The corresponding HALCON interface code must be generated.
• The corresponding package must be created especially containing the operator and interface libraries.
• The application must be linked.

First of all one has to create a definition file (file extension .def), as illustrated in figures 1.3 and 1.4. Figure 1.3
shows only the absolute minimum of information that a definition file must contain in order to call a new operator
within C programs. When using HDevelop, C++, or C#, an extended version is necessary as described in section 2.2
on page 20. The minimal form of such an extended definition is illustrated in figure 1.4. The definition file
specifies:
4 To use it within C++, C#, or Visual Basic basically the same steps are necessary, see chapter 7 on page 97.
 1.4 An Example 15

user_thresh <- CIPUserThreshold[Image:Region:Threshold$i:];

Introduction
Figure 1.3: Defining a new operator user_thresh.

user_thresh <- CIPUserThreshold[Image:Region:Threshold:]

short.german
Schwellenwert-Operator.;

short.english
Selection of gray values by thresholding.;

module
foundation;

chapter.german
BenutzerErweiterungen;

chapter.english
UserExtensions;

functionality
image;

parameter
Image: input_object;
sem_type: image;

parameter
Region: output_object;
sem_type: region;

parameter
Threshold: input_control;
default_type: integer;
multivalue: false;
sem_type: number;

Figure 1.4: An example for an extended DEF file of the operator user_thresh (minimal form), cf. %HALCONEXAMPLES%\
extension_package\halconuser\def\threshold.def.

• the name of the operator (user_thresh),

• the name of the supply procedure that has to be implemented in C (CIPUserThreshold),
• names and types of the operator’s parameter(s). The names of the parameters are only important for the
manuals and within HDevelop.
The minimal form of the extended operator DEF file includes: A short description (short), the HALCON mod-
ule (module) the operator belongs to, the mapping to a chapter (chapter) of the manual, the mapping to an
iconic object (functionality), and for every parameter its semantic type (sem_type). In addition, the type
(default_type) and number (multivalue) must be specified for control parameters.
Our operator user_thresh has got the following parameters:
• one input iconic object parameter (Image),
• one output iconic object parameter (Region),
• one input control parameter (Threshold) of type int with exactly one value and
• no output control parameter.
The operator definition within the DEF file now is used by hcomp to generate the appropriate interface code.
figure 1.5 shows the calls of hcomp. Note, that within this manual halconuser is used as name of the HALCON
16 Introduction

hcomp -u -H -phalconuser threshold.def

hcomp -u -C -phalconuser threshold.def

Figure 1.5: Calls of hcomp for HALCON/C.

package to be created. By calling hcomp with these options5 the files Hhalconuser.c (HALCON interface code),
HChalconuser.c (C-specific interface code) and HChalconuser.h (prototype of the new HALCON operator)
are created.
In the next step one has to program the new HALCON operator. This is done by implementing the supply and
action procedure. This results in the typical structure of HALCON operators as illustrated in figure 1.6.

/* action procedure */
Herror IPBThreshold(proc_handle,region,image,
width,threshold,region_out)
{
...
}

/* supply procedure - always with this parameter! */

Herror CIPUserThreshold(Hproc_handle proc_handle)
{
HGetCPar(..,&Threshold,..); /* get control */
/* parameter */
HAllSegm(proc_handle,&region,&image,1,i) /* work on all */
/* input images */
{
HCkP(proc_handle,IPBThreshold(...)); /* call action */
/* procedure */
HNewRegion(proc_handle,region_out); /* store (result) */
/* region */
}
return(H_MSG_TRUE);
}

Figure 1.6: Sample source code of supply CIPUserThreshold() and action IPBThreshold() procedure.

Compiling the source code generates an object file (in the example cipuserthreshold.o) that should be inte-
grated into the user extension library (halconuser). Moreover, the generated interface code must be converted
to the corresponding language dependent interface library: In case of a C application, this is halconuserc con-
taining HChalconuser.o. The example CMake file CMakeLists.txt in the directory %HALCONEXAMPLES%\
extension_package\halconuser can be used for generating the example package under Linux or Windows
and test programs as well.
Now we can use our new operators within C programs. But they are not yet available within HDevelop, because
the online help files have not been generated so far. There is also still missing any kind of documentation, such as
the HTML manual pages.

hcomp -u -M threshold.def

Figure 1.7: Calling the HALCON compiler hcomp to create the help files.

The online help files (as they are used e.g., by HDevelop) can also be generated with the help of the HALCON
compiler hcomp, see figure 1.7. However, to do so an extended version of the DEF file must be available. The
generated help files must be placed in the subdirectory help of the package.
The help files generated by now are used to access information about the new operators by calling specific HAL-
CON operators like get_operator_info. This important especially for constructing graphical user interfaces
5 see section 7.1 on page 97 for a complete description.
 1.4 An Example 17

like HDevelop. For the user a more convenient way to access information online is to browse through HTML
documents. The HTML documentation of HALCON operators can be generated by hcomp as well. The HTML
files have to be placed in the corresponding subdirectory doc\html\reference of the package.

Introduction
If you now add the package path to HALCONEXTENSIONS and start HDevelop the user extensions, e.g.
user_thresh, are automatically available in the specified menu (i.e., chapter). In our example this
menu is called UserExtensions as specified in %HALCONEXAMPLES%\extension_package\halconuser\def\
threshold.def.6 You can select and execute the user-defined operators like all the built-in operators of the
HALCON system. The HTML documentation is available via the Help button within the operator window.
Examples of how to use the user defined extensions in HDevelop can be found in the subdirectory examples of
%HALCONEXAMPLES%\extension_package\halconuser (*.dev). Furthermore, the *.dev programs have been
exported as C++ and C programs. The *.cpp and *.c files can be found in the subdirectory source. You can
compile them using the already mentioned CMake file. These *.cpp and *.c files also serve as an example for the
integration of user defined operators into the host languages C++ and C. Note that before compiling the exported
C++ and C code containing operators from the package halconuser, the corresponding user extension libraries
have been created. This can be done via the CMakeLists.txt in %HALCONEXAMPLES%\extension_package\
halconuser which will also generate the needed user extension C++ library halconusercpp and C library hal-
conuserc.
Please note that on some systems not all users have write permissions in the directories mentioned above. To
experiment with the example package we recommend to create a private copy in your working directory. In such a
case you must of course use the actual path to your copy when modifying environment variables.

6 UserExtensions is integrated into the menu Operator of HDevelop.

18 Introduction
 Operator Description (DEF File) 19

Chapter 2

Operator Description (DEF File)

DEF files
Note that DEF files with non-ASCII characters should be UTF-8 encoded.
The following chapters give a detailed description of the steps mentioned in chapter 1 on page 9. This is done
with respect to system-defined HALCON operators as well as to the examples within the directory %HALCONEX-
AMPLES%\extension_package\halconuser. We start with the generation of an operator description.

2.1 Short Operator Description

Before implementing an operator the author should think about the task of the operator and what kind of user
interface is best for calling the operator. This specification is used to automatically generate the interface code for
the desired host language with the HALCON compiler hcomp.
To do this, it is necessary to describe at least the following features beside the operator name in a DEF file:
• the name of the operator as used within the application programming language,
• the name of the C-procedure (supply procedure) called by HALCON in order to start the processing (this
procedure must be implemented later on),
• all iconic objects and control parameters that are needed by the operator as input (input parameters),
• all iconic objects and control parameters that are returned by the operator as result (output parameters),
• the types of these parameters,
• the number of values per parameter (there is only a distinction between parameters that need or can process
exactly one value and those expecting more than one value).

There exist two kinds of parameters within HALCON: Iconic object parameters and parameters containing any
other data – so called control parameters. By distinguishing input and output parameters we get four parameter
classes: Input iconic object parameters, output iconic object parameters, input control parameters, and output
control parameters. Basically, specifying the number of parameters per class would suffice to describe the operator.
The internal access (in particular within the supply procedure) on individual parameters works this way by using
the parameter’s position within its class. But to refer to single parameters and add further information regarding a
parameter, it is useful to give it a name.
The information specified up to now is already sufficient to integrate an operator within the HALCON/Extension
Package Interface by using hcomp. It describes the operator properly and may be specified as a “one line short
version” of the DEF file according to the following syntax:

extern_operator_name <- InternCProcedure

[InputObjects:OutputObjects:InputCtrlParams:OuputCtrlParams];

Section 2.2 explains the meaning of the single identifiers and the name convention. Please note that in contrast
to the header mentioned there, the short version header must be finished by a semicolon (;) and that the default
type and the number of values is specified together with the name of a control parameter (InputCtrlParams and
20 Operator Description (DEF File)

user_inside <- CIPUserSelect[Regions:RegionSelected:Row$i,Column$i:];

Figure 2.1: Short version of the definition of the operator user_inside (cf. %HALCONEXAMPLES%\extension_package\
halconuser\def\regionfeatures.def).

OuputCtrlParams). This is done by concatenating a dollar sign and an additional character to the name encoding
the type and number of values (cf. the example in figure 2.1).
The following table shows how to code types and number of values into a character. Lower-case characters stand for
exactly one value in the specified parameter. This corresponds to assigning multivalue: false in the extended
version. Capital letters specify parameters that contain one or more than one value (multivalue: optional).

Code
Type C-type
One Value Unlimited Number
Integer long i I
Floating-point Value double f F
String char * s S

The specification described so far is sufficient to integrate the operator into C applications. However, in general
the new operators should also be usable by HDevelop or within C++ or .NET applications. To achieve this, an
extended version of the operator description must be generated. This is described in the following section.

2.2 Extended Operator Description

An operator description within a DEF file must start with a header. The following entries are variable in their
order. All of these slots begin with a determined keyword and are finished by a semicolon (;). Semicolons within
the text not defining the end of a slot must be quoted with a backslash (\;).
Some slots are language dependent: For example short.english contains a short description of the operator
in English, short.german the same description in German. The currently supported languages are English and
German. In order to allow an international usage of operators we strongly recommend always to provide all
.english slots.
Note that all slots specified within the operator description are accessible online within the HALCON system
using the operator get_operator_info, see the Reference Manuals for details. Describing the single parameters
completes the operator description. Section 2.3 on page 28 explains how to do this.

2.2.1 Header

The operator description starts with the header

extern_operator_name <- InternCProcedure

[InputObjects:OutputObjects:InputCtrlParams:OuputCtrlParams]

Note that in contrast to the short version described in section 2.1, the header doesn’t contain any information about
the types of the control parameters (e.g. $f) and does not end with a semicolon (;).
The following example is a short version of the operator description for the dynamic threshold operator
dyn_threshold. For better legibility, there should be a comment at the beginning of every operator description,
like

/*********************** dyn_threshold *************************/

dyn_threshold <- CIPDynThreshold

[OrigImage,ThresholdImage:RegionDynThresh:Offset,LightDark:]

Comments within DEF files are indicated according to the C syntax (/* ... */).
 2.2.2 short 21

There are a couple of conventions/restrictions concerning the names of parameters: All word parts should begin
with a capital letter (for example, RegionDynThresh). They are directly concatenated without any separating
character. Especially, they must not contain any underscore (‘_’). The external operator name exclusively consists
of lower-case characters with word parts separated by underscores. This operator name is used within C programs,
low-level calls1 of the operator in C++, or within HDevelop.
The four parameter classes (input-/output iconic object/control) are separated by colons (:). One class is described
by a list of all parameter names within the class separated by commas. If there is no member of a class for an
operator, the list remains empty. The example described above defines the following mapping between parameters
and parameter classes:

parameter class keyword (cf. page 29) parameter in the example

DEF files
input iconic objects input_object OrigImage, ThresholdImage
output iconic objects output_object RegionDynThresh
input control parameters input_control Offset, LightDark
output control parameters output_control ∅

It is helpful to follow certain conventions when choosing names for parameters. They should be meaningful and
consequently should be given in English. It is convention to denote parameters that specify a position within an
image matrix by Row(s) (not line!) and Column(s) or Col(s). Parameters defining a dimension are called Width
and Height.

2.2.2 short

The keyword short starts the short description of the operator, in our example

short.english
Segment an image using a local threshold.;

As all slots specified by the keyword .english, this slot contains purely textual information. Text can be written
in different languages and can contain LATEX-commands according to special syntactic rules that are defined in
section 2.4 on page 35.

2.2.3 warning

With the slot warning, you can show a warning text in bold at the beginning of an operator description, for example

warning.english
This operator is obsolete.;

As all slots specified by the keyword .english, this slot contains purely textual information. Text can be written
in different languages and can contain LATEX-commands according to special syntactic rules that are defined in
section 2.4 on page 35.

2.2.4 abstract

A more detailed description of the operator is given within the slot abstract. The description of the example is
here shown as a shortened version:
1 Within the HALCON/C++ and HALCON/.NET class hierarchy, corresponding methods use slightly different conventions: ex-

tern_operator_name is transformed into ExternOperatorName.

22 Operator Description (DEF File)

abstract.english
\OpRef{dyn_threshold} selects from the input image those regions in which the
pixel fulfill a threshold condition. Let $g_{o} = g_{\ParRef{OrigImage}}$,
and $g_{m} = g_{\ParRef{ThresholdImage}}$. Then the condition for
\ParRef{LightDark} = \ValRef{'light'} is:
@a
g_o >= g_m + Offset
@l\[
g_{o} \ge g_{m} + \ParRef{Offset}
\]
@e
For \ParRef{LightDark} = \ValRef{'dark'} the condition is:
@a
g_o <= g_m - Offset
@l\[
g_{o} \le g_{m} - \ParRef{Offset}
\]
@e
Finally, for \ParRef{LightDark} = \ValRef{'equal'} it is:
@a
g_m - Offset <= g_o <= g_m + Offset
@l\[
g_{m} - \ParRef{Offset} \le g_{o} \le g_{m} + \ParRef{Offset}
\]
@e
This means that all points in \ParRef{OrigImage} for which the gray value is
larger or equal to the gray value in \ParRef{ThresholdImage} plus an offset
are aggregated into the resulting region.;

Again, refer to section 2.4 on page 35 for the special syntax of text.

2.2.5 module

module
foundation;

This slot denotes the module inside HALCON the operator should belong to. For user extensions the module
‘foundation’ is recommended.

2.2.6 chapter

To achieve a useful structuring of HALCON operators, they are all arranged in a hierarchy of chapters and sections.
The assignment defined in the slot chapter is reflected in the reference manuals and in the menu Operator of
HDevelop.

chapter.english
Segmentation;

The structuring can be refined by specifying a section: chapter[,section], for example:

chapter.english
Filter,Edges;

Note that it is not allowed to insert operators and sections into the same chapter at the same level of hierarchy. So
if you decide to use sections within a chapter, all operators within this chapter must be assigned to one of these
sections.
The chapters and sections created using the slot chapter may be supplemented by an optional chapter description
as described in section 2.5 on page 38.
 2.2.7 functionality 23

2.2.7 functionality

functionality
image;

This slot denotes the class of which the operator should become a method within an object-oriented programming
language like C++ or C#2 . Generally this corresponds to the semantic type of the first parameter, for example,
an image object (image). The specified name is only a symbolic one. The actual class name depends on the
programming language and is provided by the HALCON compiler hcomp. Possible values for functionality in
the current version are

DEF files
any, window, image, region, object, xld_cont, xld_poly, xld_para, xld_mod_para, xld_ext_para

2.2.8 keywords

Furthermore, one can assign a list of keywords to an operator. They are used by HDevelop to support the search
for the proper operators for a given problem, for example.

keywords.english
threshold, gray-value threshold, dynamic threshold, local threshold;

2.2.9 predecessor, successor, alternatives

The following slots also support interactive development of image processing application with HALCON.
They are used to define potential, convenient or necessary predecessor (predecessor) and successor operators
(successor) or to define alternatives (alternatives). All operators within these lists are referenced by their
name.

predecessor
mean_image,smooth_image,gauss_filter;

successor
connection,select_shape,reduce_domain,select_gray,rank_region,
dilation1,opening;

alternatives
highpass,threshold,background_seg;

2.2.10 see_also

The slot see_also contains a list of operators that are used for similar tasks or help to understand how an operator
works.

see_also
mean_image,smooth_image,gauss_filter,connection,rank_region,dilation1;

2.2.11 attention

The slot attention contains hints for using the operator or specific limitations.
2 User-defined extensions are not inserted in the class hierarchy but considered as global methods.
24 Operator Description (DEF File)

attention.english
If \ParRef{Offset} is chosen from @a -1 .. 1 @l$-1\dots1$@e
usually a very noisy region is generated, requiring large storage.
If \ParRef{Offset} is chosen too large ($>$ 60, say) it may happen
that no points fulfill the threshold condition (i.e.\ an empty
region is returned). If \ParRef{Offset} is chosen too small ($<$
-60, say) it may happen that all points fulfill the threshold
condition (i.e.\ a full region is returned).;

2.2.12 result_state

The slot result_state defines the result value of an operator and the corresponding exception handling. The
syntactical rules for the text are again the same as described in section 2.4 on page 35.

result_state.english
\OpRef{dyn_threshold} returns 2 (H\_MSG\_TRUE) if all parameters are
correct. The behavior with respect to the input images and output
regions can be determined by setting the values of the flags
\ValRef{'no_object_result'}, \ValRef{'empty_region_result'}, and
\ValRef{'store_empty_region'} with \OpRef{set_system}.
If necessary, an exception is raised.;

2.2.13 parallelization

The slot parallelization results in the manual entry Execution Information. It contains information about
the timeout and parallelization characteristics of the operator. On the one hand, this regards the possibility of using
the operator in a parallel, for example, multithreaded application and on the other hand this regards the automatic
parallelization which HALCON uses to speed up the operator’s processing when working with multi-processor or
multi-core hardware.
The slot parallelization consists of several sub-slots, each starting with a characteristic keyword followed by a
colon and finishing with a semicolon. The example below shows the slot for the operator dyn_threshold, which
is not “local”, needs neither complete nor mutual exclusion, and is parallelized on tuple and domain level. The
single subslots and their meaning will be described in the following sections.

parallelization
process_exclusively: false;
process_locally: false;
process_mutual: false;
method: split_tuple, split_domain;
region_postprocessing: domain_concat_si_inp;

• process_exclusively: true, false, none;

This subslot of parallelization assigns whether an operator is processed completely exclusively (‘true’)
by the main HALCON process/thread or not. An exclusive processing means that no other operator will
be processed by HALCON while the exclusive operator is running. If an exclusive operator is started and
other operators are still running, the processing of the exclusive operator is delayed until all other (currently
running) operators have completed.
An exclusively processed operator is always processed without any parallelization by the main HALCON
thread/process. Note that even if HALCON is reentrant for most of the operators, there are still some
operators that have to be processed exclusively due to reasons of their implementation.
If no subslot process_exclusively is filled in with an operator, it is assumed that the operator needs no
completely exclusive processing (“optimistic” assumption).
If the subslot contains none, the operator is processed by HALCON independently of other operators (even
exclusive ones). This value is only used internally by MVTec.
 2.2.13 parallelization 25

• process_mutual: true, false;

This subslot of parallelization assigns whether HALCON processes an operator under mutual exclusion
(‘true’) against itself or not. Here, a mutual exclusion means that the same operator may not run twice or
more at the same time (but other HALCON operators can).
An mutually processed operator is always processed without any parallelization by the main HALCON
thread/process.
If no subslot process_mutual is filled in with an operator, it is assumed that the operator needs no mutual
exclusion (“optimistic” assumption).

• process_locally: true, false;

This subslot of parallelization assigns, whether an operator must be processed locally (‘true’) by a

DEF files
program thread, or whether it may called by any (“external”) thread without problems.
If process_locally is set to ‘true’, this signals the programmer that the corresponding operator must
be used carefully within multithreaded applications. The simplest way to avoid any problems with such
operators is to process them all under mutual exclusion within the main thread of the program.
As a side effect, HALCON processes an operator without parallelization regardless the settings of the sub-
slots method and domain_split, if process_locally is set to ‘true’. This avoids problems with ‘local’
operators and multithreading and makes sense because ‘local’ operators normally are responsible for graph-
ical interaction and thus are not suitable for parallelization.
If no subslot process_locally is filled in with an operator, it is assumed that the operator must be pro-
cessed “locally” (“pessimistic” assumption). However, this subslot should be filled in in any case, because
it contains a very useful information for programmers of multithreaded applications.
• method: none, split_tuple, split_channel, split_domain, split_partial,
split_partial_domain;
This subslot of parallelization can contain one or more of the strings above and specifies, which type
of (automatic) parallelization the operator is suitable for:
• none: HALCON does not automatically parallelize the operator.
• split_tuple: HALCON parallelizes the operator by splitting every input image tuple into several
subsets of the tuple; the tuple subsets are then processed in parallel.
• split_channel: HALCON parallelizes by splitting every multichannel (input) image into several
subsets of the channels; the subsets are then processed in parallel.
• split_domain: HALCON parallelizes by splitting the domain of every input image into several parts;
the parts are then processed in parallel.
• split_partial, split_partial_domain: These methods are only used by MVTec to indicate the
internal parallelization of HALCON operators.
If method is set to anything other but ‘none’, the parameter slot costs_weight must be filled in for every
input control parameter and the parameter slot postprocessing must be filled in for every output control
parameter of the operator (see page 31)!
If method is set to ‘split_domain’, the slot region_postprocessing (see below) must also be set correctly
and may not be omitted!
If the slot process_locally is set to ‘true’, method should be set to ‘none’, because the operator won’t be
parallelized then (see description of process_locally above).
Note that the slot method may contain any combination of the strings ‘split_tuple’, ‘split_channel’, and
‘split_domain’, because an operator may be parallelized by using any combination of those three methods.
However, if ‘none’ is specified with the slot method, no other string should be specified with it in order to
keep the description consistent.
If no slot method is filled in with an operator, it is assumed that the operator is not suitable for being
automatically parallelized (“pessimistic” assumption).
• region_postprocessing: none, domain_concat_si_inp,domain_concat_mult_inp;
This subslot of parallelization must (only) be set for operators that are suitable for being parallelized
by splitting the domain of input objects (i.e. slot method contains ‘split_domain’). For such operators
HALCON supports a simple postprocessing of output region components: After splitting the domain of
input objects and processing the operator in parallel (within the subparts of the original domain), HALCON
26 Operator Description (DEF File)

creates the overall output iconic objects based on the output objects of the parallel processing. At this, it
supports three methods for determining the domain/region components of overall output objects. Those
three methods correspond to the three possible values of region_postprocessing:
• none: no postprocessing of region/domain components. Here, HALCON directly adopts the region
components of input objects and re-uses them unchanged as the region components of the correspond-
ing overall output objects. This method is especially suitable for operators which output solely image
objects and where the domain is left unchanged, such as filter operators (e.g. mean_image).
• domain_concat_si_inp: postprocess region components by concatenation for operators which have
only a single input iconic parameter. Here, HALCON creates the region components of overall output
objects by concatenating the region components of the corresponding output objects of the parallel
processing. At this, the latter regions must not overlap! Therefore, domain_concat_si_inp can only
be used for operators, for which the subslot domain_split (see below) is set to ‘0’. This method is
suitable, for example, for the operator threshold which outputs a region containing all pixels of a
certain gray value range. Here, HALCON splits the input domain into disjunctive parts, processes the
threshold operator in parallel, and finally concatenates the single result regions to one overall result
region.
• domain_concat_mult_inp: postprocess region components by concatenation for operators which
have multiple input iconic parameter and which need a specific handling of the input objects. This
method is quite similar to that above, i.e., HALCON also creates the region components of overall
output objects by concatenating the region components of the corresponding output objects of the par-
allel processing. Again, the latter regions must not overlap! Therefore, domain_concat_mult_inp
can only be used for operators, for which the subslot domain_split (see below) is set to ‘0’. For
domain_concat_mult_inp HALCON uses a specific handling of input objects. Normally, HAL-
CON splits the domains of all objects of all input iconic parameters in the same manner (e.g. by
splitting into the first and the second half of the chords, independent from the row index of the chords).
This does not mean any problem as long as all input image domains are the same — especially, if
domains of corresponding objects of different input parameters are the same. Because then also the
split domains will match each other. This is not the case, if we have to expect that domains of objects
of different input iconic parameters may differ. Here, it may happen that split domain parts of the first
parameter and that of the second parameter do not overlap because of the simple splitting mechanism
which does not take into account the row index of chords. If so, and if an operator uses, for example,
an intersection of the input domains of different input parameters for defining the valid domain of
the processed operation, it would get an empty region — in contrast to the sequential processing of
the same operator. Therefore, we must assign domain_concat_mult_inp for such operators. This
will force HALCON to only split the domains of the objects of the first input iconic parameter. The
domains of input objects of all other input iconic parameters are left unchanged so that they fit to the
domains of the first input iconic parameter regardless of their position in the image.
This method is suitable, for example, for the operator add_image which adds two images and sets the
domain of the result image to the intersection of the domains of the two input images. By defining
domain_concat_mult_inp for add_image, HALCON only splits the domain of the first image to
add, then calculates the intersection of the split domain parts with the unchanged domain of the second
image in parallel, performs the addition of gray values in parallel, and finally merges the resulting
region components (domains) by concatenation into the region component of the overall output image
which also contains the added gray values.
• abort_mode: break, cancel, both;
This subslot of parallelization must only be used to determine the supported timeout mode. In case no
timeout is supported, this slot must be omitted. For an explanation of the different modes, see the reference
manual entry for set_operator_timeout.

Though, we recommend to specify the whole slot parallelization, it is also possible to completely leave it
out in an operator’s description. In this case, it is assumed that the operator is reentrant, i.e. it is not processed
under (complete or mutual) exclusion, and that it must be processed “locally”. The latter also means that no
parallelization is used when processing the operator. This assumption corresponds exactly to those which are used
in the case of missing single subslots (see descriptions above).
 2.2.14 complexity 27

2.2.14 complexity

The slot complexity describes the complexity of the operation in terms of number of points along a contour, the
area of an image region etc.

complexity.english
Let $F$ be the area of the input region. Then the runtime
complexity is $O(F)$.;

2.2.15 example

DEF files
It is possible to describe an example under the keyword example in order to illustrate the usage of an operator. An
extension of the keyword specifies the programming language of the example.

example.trias
/* Looking for regions with the diameter D: */

mean_image(Imaged,Mean,D*2,D*2)
dyn_threshold(Image,Mean,Seg,5,'light')
connection(Seg,Objects);

The extension .trias indicates a HDevelop example. Moreover, the extensions .c, .cpp, and .c# can be used.
The text of the example is processed unmodified, so it must not contain any LATEX-special characters. The only
exception is the semicolon that needs a prefixed backslash, because it would signal the end of the example text
otherwise. This must be considered especially for C, C++, and C# examples.

2.2.16 references

The slot references (not specified in the dyn_threshold example) is used to insert references to literature into the
documentation, for example:

references
R.M. Haralick, K.G. Shapiro: ``Computer and Robot Vision''\;
Vol. 1, Addison-Wesley Publishing Company, 1992.;

2.2.17 class Information

At the end of the DEF file, i.e., after the parameter section described in the following section, information about the
classes generated for HALCON/.NET must be added, in particular the COM class and library IDs in the subslots
iid, clsid, and libid. The example below shows the corresponding information in threshold.def.

class halconuser <- user

short.english
Sample extension package.;

iid
{bf6a1001-0b95-11d4-b295-00e0293dc2ac};

clsid
{bf6a1002-0b95-11d4-b295-00e0293dc2ac};

library halconuser <- user_library

libid
{bf6a1000-0b95-11d4-b295-00e0293dc2ac};
28 Operator Description (DEF File)

2.3 Describing the Parameters

Please note that the number of parameters is limited for an extension package operators as listed in the Installation
Guide, section 1.5.6 on page 13.
Again, the definition of dyn_threshold is used as an example. Every description of a single parameter starts
with the keyword parameter and contains several slots. A slot begins with a characteristic keyword followed by
a colon and is finished by a semicolon. All slots specified for the parameters of an operator are accessible online
within the HALCON system using the operator get_param_info, see the Reference Manuals for details.
parameter
OrigImage: input_object;
description.english: Image to be segmented.;
sem_type: image;
type_list: byte,int2,int4,real;
multivalue: optional;

parameter
ThresholdImage: input_object;
description.english: Image containing the local thresholds.;
sem_type: image;
type_list: byte,int2,int4,real;
multivalue: optional;

parameter
RegionDynThresh: output_object;
description.english: Segmented regions.;
sem_type: region;
multivalue: optional;

parameter
Offset: input_control;
description.english: Offset added to ThresholdImage.;
sem_type: number;
type_list: integer,real;
default_type: real;
default_value: 5.0;
values: 1.0, 3.0, 5.0, 7.0, 10.0, 20.0, 30.0;
multivalue: false;
assertion: -255 < Offset && Offset < 255;
costs_weight: 0;

parameter
LightDark: input_control;
description.english: Extract light, dark or similar areas?;
sem_type: string;
type_list: string;
default_type: string;
default_value: light;
value_list: dark,light,equal,not_equal;
multivalue: false;
costs_weight: 0;

The minimum of information needed for every parameter is its name and type, its default type, its semantic type,
the number of values allowed (multivalue), and, if the operator should be automatically parallelized, the “costs
weight” of input control parameters and the “postprocessing” of output control parameters, see below.

2.3.1 Name
parameter
Name: input_object,output_object,input_control,output_control;
 2.3.2 default_type 29

This defines the name and the class of a parameter. The parameters must be described in the same order as in their
definition within the header of the operator description.
Note that in order to create PDF hyperlinks referencing parameters (see section 2.4 on page 35 and section 7.1.4
on page 99) a parameter name must consist of alphanumerical characters only!

2.3.2 default_type

default_type: handle, integer,real,string;

Only for control parameters! This slot specifies, what C-type to use in general. It must have exactly one of the four

DEF files
above values.

2.3.3 sem_type

sem_type: class[.spec];
This slot determines the semantic type, i.e., it specifies the class of data passed as parameters, when using an
object-oriented language. Names of classes within the DEF file are only symbolic. The mapping to the actual class
names is provided by the HALCON compiler hcomp.
HDevelop also uses the semantic types, for example, to provide specific inspection routines. A list with the
semantic types is given in appendix B on page 141. Some exemplary semantic types (classes) are shown below.

• Iconic data (object parameters):

– object (any iconic object: images, regions, XLDs)
– image (images)
– region (regions)
– xld (any XLDs: lines in eXtended Line Description)
– xld_cont, xld_poly, xld_para, xld_mod_para, xld_ext_para

• Elementary data (control parameters):

– number (unspecific)
– integer, real, string
– channel (channel number)

• Handles (control parameters):

– window (HALCON graphics window)

• Arrays (control parameters):

– histogram.values (gray value histogram)
– distribution.values (distribution)

• Geometric data (control parameters):

– point.x, point.y (position; (column, row) except for 2D transformations to get mathematically
positive rotation)
– extent.x, extent.y (dimensioning)
– angle.deg, angle.rad (angle given in degrees or radians, respectively)
– circle.center.y, circle.center.x, circle.radius (circle)
– line.begin.y, line.begin.x, line.end.y, line.end.x (line)
30 Operator Description (DEF File)

– rectangle.origin.y, rectangle.origin.x (rectangle: upper left corner),

rectangle.corner.y, rectangle.corner.x (lower right corner) or
rectangle.extent.x rectangle.extent.y (expansion – as alternative to specifying the 2nd cor-
ner)
– rectangle2.center.y, rectangle2.center.x (rectangle with arbitrary orientation: center),
rectangle2.angle.rad (orientation – in radians),
rectangle2.hwidth, rectangle2.hheigth (half the size)
– ellipse.center.y, ellipse.center.x (ellipse: center),
ellipse.angle.rad (orientation – in radians),
ellipse.radius1, ellipse.radius2 (radii)
– arc.center.y, arc.center.x (circle: center),
arc.angle.rad (angle stretched by the circular arc – in radians),
arc.begin.y, arc.begin.x (starting point of circular arc).
– hom_mat2d (2D homogeneous transformation matrix)
hom_mat3d (3D homogeneous transformation matrix)
pose (3D pose)

• Numerical region descriptions (control parameters):

– coordinates.y, coordinates.x (coordinates)
– contour.y, contour.x (points of a contour)
– chord.y, chord.x1, chord.x2 (runlength code)
– polygon.y, polygon.x (polygonal representation)
– chain.begin.y, chain.begin.x, chain.code (chain code)

• Miscellaneous (control parameters):

– filename (name of a file)
filename.read (name of an input file)
filename.write (name of an output file)
– attribute.name (name of a generic parameter)
attribute.value (value of a generic parameter)

Please note:

• Please use the above semantic types for characterizing parameters whenever they are applicable.
• For control parameters characterizing a composed object like a circle etc.: Please use the specific order of
parameters like indicated above.

2.3.4 modified

modified: false,true;
This slot is used to indicate input parameters that may be modified by the operator, for example, handles. If
modified is set to ’true’, a respective note is automatically created in the corresponding reference manual entry.

2.3.5 multivalue

multivalue: true,false,optional;
This slot describes the number of values passed in a parameter: ‘true’ means that an array (tuple) of values must
be passed. If ‘false’ is specified, exactly one value must be passed. ‘optional’ allows both. If a parameter may also
return no values at all, multivalue must be set to ‘true’ or ‘optional’.
All slots mentioned so far must appear in any extended operator description. Moreover, the following optional
slots are recommended to provide further information about parameters:
 2.3.6 costs_weight 31

2.3.6 costs_weight

costs_weight: an unsigned integer value;

This slot must only be used for input control parameters of operators which are suitable for being automatically par-
allelized (i.e. for operators for that the parallelization subslot method does not contain ‘none’; see page 25).
Here, it assigns, whether the time for processing the operator directly depends on the content (value) of the corre-
sponding input control parameter. If costs_weight is set to ‘0’, the duration of the operator processing does not
directly depend on the content of the corresponding input control parameter. In this case, the parameter will not
be taken into account when HALCON decides, whether an operator should be parallelized for a given allocation
of input parameters or not. This also means, that this parameter will not be checked during the hardware training
(compare the description of optimize_aop in the Reference Manuals). This helps to speed up the training. If

DEF files
costs_weight contains a value greater than ‘0’, this assigns that there is a direct dependency between the content
of the corresponding input control parameter and the computation time of the operator. In this case, HALCON will
take into account this parameter during its hardware check (optimize_aop) in order to determine its influence on
the operator’s processing time. Note that the slot costs_weight must be filled in for every input control parame-
ter, if the operator should be automatically parallelized, i.e. if the operator’s slot method does not contain ‘none’
(see page 25).

2.3.7 postprocessing

postprocessing: none,tuple_add,tuple_min,tuple_max,tuple_concat,
channel_add,channel_min,channel_max,channel_concat,
domain_add,domain_min,domain_max,domain_concat;
This slot must only be used for output control parameters of operators which are suitable for being automati-
cally parallelized (i.e. for operators for that the parallelization subslot method does not contain ‘none’; see
page 25). Here, postprocessing specifies, which kind of postprocessing is used with the single result values of
a parallel processed operator. If, for example, an operator is parallelized by splitting a tuple of iconic input objects
and the single result values of the parallel processed operator must be put into one output control object again, the
slot postprocessing should contain the keyword ‘tuple_concat’ which means “concatenate result values”. Or
if an operator is parallelized by splitting the single channels of iconic input objects and the overall result value is
the minimum of the single result values of the parallel processed operator, postprocessing should contain the
keyword ‘channel_minimum’. Obviously, the slot postprocessing can contain several strings in order to define
different postprocessing steps for different levels of parallelization (tuple, channel, and domain); of course, there
should only be one string per level. If ‘none’ is specified (in this case, no other string should be specified), no
postprocessing is done on every parallelization level. This means, that the overall result value of the corresponding
output control parameter is directly determined by the result value of the first parallelized operator instance (e.g.
the instance which worked on the first tuple element).
Altogether, HALCON currently supports the following postprocessing steps:

• none: no postprocessing; adopt first value;

• tuple_add: overall result value is the sum of the single result values of the tuple parallelization;
• tuple_min: overall result value is the minimum of the single result values of the tuple parallelization;
• tuple_max: overall result value is the maximum of the single result values of the tuple parallelization;
• tuple_concat: overall result value is a tuple which contains all the result values of the tuple parallelization
(“concatenation”);
• channel_add: overall result value is the sum of the single result values of the channel parallelization;
• channel_min: overall result value is the minimum of the single result values of the channel parallelization;
• channel_max: overall result value is the maximum of the single result values of the channel parallelization;

• channel_concat: overall result value is a tuple which contains all the result values of the channel paral-
lelization (“concatenation”);
• domain_add: overall result value is the sum of the single result values of the parallelization on domain level;
32 Operator Description (DEF File)

• domain_min: overall result value is the minimum of the single result values of the parallelization on domain
level;
• domain_max: overall result value is the maximum of the single result values of the parallelization on domain
level;
• domain_concat: overall result value is a tuple which contains all the result values of the parallelization on
domain level (“concatenation”);

The example below shows the definition of postprocessing for the operator circularity, which calculates the
shape factor for the circularity (similarity to a circle) of input regions. If circularity is tuple parallelized the
overall result is a tuple of values, of which the single elements contain the “circularity” of the single input regions.
Thus the postprocessing of the corresponding output control parameter is assigned by ‘tuple_concat’.

parameter
Circularity: output_control;
description.english: Roundness of the input region(s).;
sem_type: real;
type_list: real;
default_type: real;
multivalue: optional;
assertion: 0 <= Circularity && Circularity <= 1.0;
postprocessing: tuple_concat;

Note that the slot postprocessing must be filled in for every output control parameter, if the operator should be
automatically parallelized, i.e. if the operator’s slot method does not contain ‘none’ (see page 25).

2.3.8 description

description.english: LATEX/Ascii-Text;

This slot contains a short description of the parameter. The extension .english refers to a English description. In
addition to that a German description might be given in description.german. For the syntax of LATEX/Ascii-Text
see section 2.4 on page 35.

2.3.9 type_list

The slot type_list is only used in connection with object parameters with sem_type = image and for control
parameters.
For images (sem_type = image):
type_list: any,byte,int1,int2,int4,real,cyclic,direction,complex;
For images this slot contains an enumeration of all supported pixel types. Note that in many cases there will be
more than one supported pixel type. Thus, type_list is a list separated by commas.
For control parameters:
type_list: handle, integer,real,string;
For control parameters this slot contains a list of all C-types allowed for the parameter.

2.3.10 default_value

default_value: Default;
This slot defines the default value used by HDevelop to initialize the parameter in the operator window, for example.
Suggesting default values can help the programmer to find suitable values of parameters. Generally, strings are
unquoted in the description (not 'theString', but theString); exceptions: empty string ('') and strings with
special characters ('the string').
 2.3.11 values 33

2.3.11 values

values: Suggested values;

This slot contains a collection of possible values. This list does not have to be complete. It just suggests some
typical values the user might want to try.

2.3.12 value_list

value_list: List of values;

DEF files
This slot contains a complete list of all allowed values. So, if a parameter can hold only a discrete number of
specific values, value_list should be specified, otherwise values might be used to provide some typical values.

2.3.13 value_min, value_max

value_min: Number;
value_max: Number;
Instead of a list an interval may be used to specify a range of values for a parameter. The interval may be unlimited
in one direction. The slot value_min specifies the minimum of the allowed values, value_max the maximum.
Please note that the range is not used to check the passed parameter values. The slots are provided for applications
that need the possible range of values to create sliders or other graphical elements to interact with parameters.
To restrict the values of a parameter, please use the slot assertion further below.

2.3.14 step_rec, step_min, value_function

step_rec: Number;
step_min: Number;
value_function: lin,log,quad, . . . ;
If a range of values is possible for a parameter it might be a useful information to specify a suitable step width
(step_rec) between distinct values to be tested. Based on this information a user interface might generate a
list of suggestions for parameter values. The corresponding minimum reasonable step width can be provided by
step_min. The step width can also be modified by specifying a function in the slot value_function.

2.3.15 value_number

value_number: boolean expression;

This slot contains a boolean expression that determines how the number of passed or returned values of a parameter
is absolutely or relatively connected to the number of values in other parameters or some absolute values. The
operators and functions listed in table 2.1 may appear within the expression.
Examples:

• Param1 == Param2 && Param2 > 0

This means that the same number of values and at least one value must be passed with parameter 1 and
parameter 2.
• Param2 == 3
This means that exactly three values must be passed with parameter 2.

For output parameters this can be seen as an assertion. This may also refer to input parameters, e.g.:
RegionOut <= RegionIn in connection with the HALCON operator select_shape expresses the fact that the
number of output regions does not exceed the number of input regions.
34 Operator Description (DEF File)

Group Symbol meaning

Unary Operators ! logical NOT
- negation
Binary Operators && logical AND
|| logical OR
== equal
!= not equal
> greater
>= greater or equal
< less
<= less or equal
+ sum
- difference
* multiplication
/ division (DIV)
% rest of division (MOD)
Functions odd true, if odd
even true, if even
ld binary logarithm
length length
number number of values (only for assertion)
width (image-)width
height (image-)height

Table 2.1: Operators and functions used for the slots value_number and assertion.

2.3.16 assertion

assertion: boolean expression;

This slot contains a boolean expression that determines how the passed or returned values of parameters are ab-
solutely or relatively connected to the values of other parameters or some absolute values. The same expressions
may appear as described above for value_number, see table 2.1.
Examples:

• Param1 == Param2 && Param2 > 0

This means that parameter 1 and 2 must have the same value and this value is greater than 0.
• 0 <= Param2 && Param2 <= 255
This means that parameter 2 must have a value between 0 and 255.
• Param1 <= number(ImageIn)
This means that the value of parameter 1 must be less or equal the number of input images.
• Param2 < width(ImageIn) && Param2 >= 0 && odd(Param2)
This means that the value of parameter 2 must be between 0 and the width of the input image and must be
an even number.

2.3.17 multichannel

multichannel: true,false,optional;

This slot is only used in connections with image objects. It contains an assertion about the necessary or supported
number of channels of an image. If set to false, the processing is done only on the first channel (all others are
ignored), if set to true, a multichannel image must be passed. optional specifies operators that can work on
more than one channel but can also work on only one channel as well.
 2.3.18 multiinstance 35

2.3.18 multiinstance

multiinstance: true,false,optional;

This slot is used for semantic tuples. A semantic tuple is a tuple of values that, put together, describes a single
instance, for example, a pose (consisting of seven values) or calibration parameters (consisting of several values,
depending on the camera type).
The slot multiinstance is only used if multivalues = true. As for one instance multiple values need to be
permitted you can use multiinstance in order to specify if multiple semantic tuples may be passed (true) or
not (false). optional specifies operators that can work on both one or more semantic tuples.

DEF files
2.3.19 file_ext, file_ext_descr

file_ext: List of file extensions;

file_ext_descr.english: List of descriptions;

These slots are used for parameters of the semantic type filename (see section 2.3.3 on page 29). In file_ext,
you can specify a list of possible file extensions. HDevelop, for example, uses this information when opening file
selectors.
In file_ext_descr.english (and file_ext_descr.german), you can add descriptions for the extensions. If
file_ext contains a list of extensions, you can either pass a single description for all of them or one for each
extension. When passing a list of descriptions, you can insert a period to indicate that the previous value should
be used. If a description contains a space, you must enclose it in single quotes. Note that HDevelop automatically
appends the text Files to the descriptions.
Example 1: file_ext: tif,tiff,gif;
file_ext_descr.english: Image;
results in: Image Files (*.tif; *.tiff; *.gif)

Example 2: file_ext: tif,tiff,gif;

file_ext_descr.english: 'TIFF Image',.,'GIF Image';
results in: TIFF Image Files (*.tif)
TIFF Image Files (*.tiff)
GIF Image Files (*.gif)

2.4 Text in DEF Files

Note that DEF files with non-ASCII characters should be UTF-8 encoded.
Within a DEF file, the semicolon (;) is used to separate the single slots. So, when using a semicolon within a text,
it must be quoted with a backslash (\;).
DEF files are not only used to create interface code, but also allow the generation of PDF reference manuals,
the HTML documentation, and the help files used to access operator knowledge via HALCON operators like
get_operator_info. For the online help and the HTML files an ASCII version of each text is needed, whereas
the reference manuals are produced compiling a LATEX-file generated from the DEF files. To avoid the necessity
of writing two text blocks for one operator (ASCII and LATEX), both versions are generated by using one text.
Therefore, the following conventions must be observed:

Quotation marks: There are two kinds of quotation marks

’string’: This notation signals that the quoted text is a string as used within programming languages. So
hcomp treats 'string' as a string-parameter.
36 Operator Description (DEF File)

“Text”: This notation must be used in all other cases, particularly when quoting a word or text segment
because of its content. So hcomp treats ``Text'' as a quoted section of a text. Please do not forget or
permute the quotation marks (starting with `` and ending with '').
Underscores: Underscores can be used directly for both the ASCII and the LATEX output. The HALCON compiler
hcomp automatically prefixes them with the necessary backslashes for the LATEX output (\_).
Please note that if you want to use an underscore in a LATEX part to create a subscript, you must encase the
subscript text in curly braces ({}) even if the subscript is only a single character. For example, to create the
output “Sx ” you must write $S_{x}$. If you leave out the braces, an underscore is printed, for example,
$S_x$ results in “S_x”.
Backslash: All backslashes (\) within the text are ignored while generating the ASCII version. So the LATEX-
linefeed-symbol (\\) can be used without any problems. To embed a literal backslash in the output, use
\textbackslash{} in the DEF file.
Tilde: To use the tilde (for example, as symbol for negation: set_check(::'~clear':)), the following special
notation must be used for the LATEX-text: set_check(::'\~{}clear':).
Formulas: Short formulas can be bracketed by dollar symbols ($) just as in LATEX. These symbols are ignored for
the ASCII version of the text.
To set an index of one character (for example, Ab ) LATEX allows to simply write $A_b$. This is not possible
here, because of the special underscore handling. Therefore, any index must be written exactly as any longer
index within LATEX: A_{b}.
HALCON: The string HALCON is generated by \Halcon. Note that in the PDF files derived from the generated
LATEX version of the DEF files, no space is generated after the string HALCON. Thus, if you do not want
to start the next character/string without a blank, that is concatenated to the string HALCON, you should
use \Halcon\ instead. So “\Halcon XYZ” results in “HALCON XYZ” and “\Halcon\ XYZ” results in
“HALCON XYZ”. With the ASCII version all backslashes are ignored (see above).
Names of parameters and operators: Any reference to extension package operators or their parameters must be
written as \OpRef{operator_name}, respectively as \ParRef{parameter_name}. These keywords and the
brackets are ignored, when generating the ASCII version so that only operator_name or parameter_name
remains in the ASCII file. In the HTML and PDF documents, hyperlinks are generated from these references.
Parameter values: A specific value for a parameter should be written as \ValRef{parameter_value}. For ex-
ample, the parameter \ParRef{LightDark} of the operator \OpRef{dyn_threshold} can hold one of the
values \ValRef{’light’}, \ValRef{’dark’}, or \ValRef{’equal’}. The keyword ValRef and the brackets
are ignored, when generating the ASCII version so that only parameter_value remains in the ASCII file.
Paragraphs: If you want to divide a longer text into paragraphs to increase the readability, all you need to do is
to insert an empty line between the paragraphs:

This is a paragraph ...

.. which ends here.

The next paragraph starts after an empty line ...

This corresponds to the standard LATEX way of separating paragraphs; in the HTML documents, the para-
graphs are enclosed with the tag <P>.
Chapter references: You can add a link to a certain chapter or section using \ChapRef{chapter} or
\ChapRef{chapter, section}, respectively. The chapter/section names must match the English names of
an existing chapter definition, see section 2.2.6 on page 22.
Formatted text: You can use the following LATEX commands to format text both in the LATEX and HTML ver-
sion:
• \emph{text}: results in text (HTML tag <E>)
• \texttt{text}: results in text (HTML tag <TT>)
• \textbf{text}: results in text (HTML tag <B>)
• \textit{text}: results in text (HTML tag <I>)
 2.4 Text in DEF Files 37

Please note that these commands cannot be nested!

Links: The following special environment adds a hyperlink to the specified URL into the HTML version of the
documentation. In the LATEX version, the link text appears as plain text.

\begin{External}{URL}
Link text...
\end{External}

Lists: You can use the following LATEX environments to format text in lists both in the LATEX and HTML version:

DEF files
description lists:
\begin{description}
\item[title 1] text ...
\item[title 2] text ...
\end{description}

lists with bullet points:

\begin{itemize}
\item text ...
\item text ...
\end{itemize}

enumerated lists:
\begin{enumerate}
\item text ...
\item text ...
\end{enumerate}

Paragraph alignment: You can use the following special environment to specify the alignment of the included
text. The parameter format may be set to left, center, or right.

\begin{Alignment}{format}
...
\end{Alignment}

Tables: You can use the following special environment to format text in tabular format both in the LATEX and
HTML version. This table environment is not to be confused with the standard LATEX table or tabular
environment. Tables are centered by default. To change the alignment of a table, enclose it in the Alignment
environment (see above).

\begin{Table}[style]{format}
column & column & .. \\
column & column & ..
\end{Table}

Columns are separated by &, and a new row is started with \\. Note that the last row of the table has no
trailing \\.
The style specification (including the square brackets) is optional. The following values are available:
layout: Simple table without any borders. This is the default if no table style is specified.
grid: Each table cell has a border.
table: The first row is formatted as the table header. The header and the bottom of the table are marked
with horizontal lines.
38 Operator Description (DEF File)

The format specification defines the number of columns, their alignment, and (optionally) their width.
Each occurrence of one of the letters l, r, or c defines a left-aligned, right-aligned or centered column,
respectively. The column specifier may be followed by a number which defines the relative width of the
column in percent. Note that the alignment of a column is disregarded in the LATEX version if the width is
specified. In that case the text of the corresponding column is justified.
For readability, the column specifications may be separated by commas. Extra spacing is ignored. Thus the
following table specifications are equivalent:
\begin{Table}{l 40, c 30, r 30}

\begin{Table}{l40c30r30}

Other LATEX commands: If you want to use additional LATEX command within a text segment, two versions of
this segment must be provided – one for ASCII (with @a signaling the start of the ASCII section) and another
as pure LATEX text (with @l starting the LATEX version and @e ending the special section). In particular, this
technique is necessary for tables and larger formulas.
Example:
@a g_o >= g_m + \ParRef{Offset}
@l\[ g_{o} \ge g_{m} + \ParRef{Offset} \]@e
This parenthesis can also be used for only one of the two text types:
... text text @l \aSpecialLatexCommand @e text text ...
In fact, the ASCII mode has two sub-modes: If @a is immediately followed by a carriage return, the following
lines are enclosed with the HTML tag <PRE>. Thus, they appear “as they come”, including all spaces and
carriage returns. Otherwise, i.e., if @a is followed by any character (including a space!), carriage returns and
spaces are not preserved in the HTML document.

2.5 Chapter Description

Chapters and sections define the structuring of HALCON operators. Sometimes, it is desirable to add an introduc-
tory text to a certain chapter or section, for example, to explain some common concepts of the contained operators.
These chapter descriptions are defined at an arbitrary place in the DEF file outside of an operator description.
They are linked to the corresponding chapter using a header that lists the English chapter name, and optionally the
English section name:

chapter_ref chapter[,section] <- user_chapter

The chapter/section names must match the English names of an existing chapter definition, see section 2.2.6 on
page 22.
The text of the chapter description is given within the slot abstract. It follows the rules of the slot abstract
used in the operator descriptions. The syntax is explained in section 2.2.4 on page 21.
Thus, a full chapter description looks like this:

chapter_ref Filter,Edges <- user_chapter

abstract.english
Text of the chapter description
...
;

abstract.german
...
;

...

Again, refer to section 2.4 on page 35 for the special syntax of text.
 Style Guide for Programming 39

Chapter 3

Style Guide for Programming

The following chapter contains some recommendations for implementing new HALCON operators. They aim on
portable code that should be easy to understand for other HALCON programmers. One of the major topics is the
memory management discussed in section 3.2 on page 41.

Style Guide
3.1 Basic Numeric Data Types

This section describes the usage of basic numeric data types. Since C made no assumption about the size of integers
prior to the introduction of the C99 standard, HALCON versions 20.11 and earlier define the following types:

Type Name C99 Type Name Size/Range of Values

INT1 int8_t one byte with sign
HBYTE uint8_t one byte, unsigned
UINT1 uint8_t the same as HBYTE
INT2 int16_t two bytes with sign (generally short)
UINT2 uint16_t two bytes, unsigned
INT4 int32_t four bytes with sign
UINT4 uint32_t four bytes, unsigned
INT4_8 four (on 32 bit systems) or eight (on 64 bit systems) bytes with sign
UINT4_8 four (on 32 bit systems) or eight (on 64 bit systems) bytes, unsigned
HINT int At least two, maximal eight bytes with sign
HUINT unsigned At least two, maximal eight bytes, unsigned

Using these types ensures the portability of HALCON operators. If the extension package need not be compilable
for HALCON 20.11 or earlier versions, the C99 data types (defined in the stdint.h header file) should be used
where applicable. Note that C99 does not define any types that exactly match the INT4_8 or UINT4_8 types.

3.1.1 Attributes of Iconic Parameters

To use operators in HALCON and HALCON XL, the following types have been introduced. With a compiler
define (see chapter 7 on page 97), they are mapped to the suitable basic types for the corresponding image size.
40 Style Guide for Programming

#if !defined(HC_LARGE_IMAGES)
typedef int32_t HIMGDIM; /* Image dimension, e.g., width and height */
typedef int16_t HIMGCOOR; /* Image coordinates, e.g, row and column */
typedef int32_t HLINCOOR; /* Linearized image coordinates */
typedef int32_t HIMGCNT; /* Number of pixels, e.g., area or buffer size */
typedef int32_t HITEMCNT; /* Number of elements (contours or runlengths) */
typedef float HSUBCOOR; /* Sub-pixel precise coordinates */
typedef float HSUBATTR; /* Sub-pixel precise attributes of contours */
#else
typedef int32_t HIMGDIM;
typedef int32_t HIMGCOOR;
typedef INT4_8 HLINCOOR;
typedef INT4_8 HIMGCNT;
typedef INT4_8 HITEMCNT;
typedef double HSUBCOOR;
typedef double HSUBATTR;
#endif

Examples for their use can be found in chapter 4 on page 49.

3.1.2 Local Variables / Temporary Results

Types and sizes for local variables (no arrays) should be handled as follows:

Type Size C-Data Type

1 byte
int (HINT) or unsigned (HUINT)
2 byte
Integer
3 byte
INT4_8 or UINT4_8
4 byte
Floating-point Number double

3.1.3 Procedure Parameters

Parameters of procedures should be of the following types within HALCON:

Type Size C-Data Type

1 byte
HINT
2 byte
Integer
3 byte
INT4_8
4 byte
Floating-point Number double
Structure pointer

3.1.4 Arrays

For arrays or structures (i.e. larger sets) always the smallest possible data type should be used.

Type Size C-Data Type

1 byte int8_t
2 byte int16_t or uint16_t
Integer
3 byte
int32_t or uint32_t
4 byte
4 byte float
Floating-point Number
8 byte double
Structure pointer
 3.2 Memory Management 41

3.2 Memory Management

HALCON provides a sophisticated memory management not only to handle iconic objects, but also to allo-
cate/deallocate arbitrary data. Please use the corresponding HALCON Extension Package Interface routines exclu-
sively. Do not create/destroy memory blocks on the heap with the standard routines of the operating system (like
malloc and free) since the HALCON routines provide a caching mechanism, garbage collection for temporary
data, and debugging facilities. See the technical note HALCON Memory Management for details on the caching
mechanisms in HALCON.
We strongly recommend not to use global variables within HALCON operators. If they are not avoidable at
least make them static within the file of usage. If even this is undesirable group them into structures to keep the !
number of global names small.
If you use static variables, be aware that they are shared between multiple threads. Please note that HALCON
uses multithreading to exploit multi-processor or multi-core hardware. This means, that multiple instances of your
code will actually share all the static variables! Furthermore, be aware that large static arrays consume a lot of
memory – keep in mind that HALCON is a very large system enfolding hundreds of operators.

3.2.1 Temporary Data

Style Guide
Names

HAllocTmp, HFreeTmp, HFreeNTmp, HFreeUpToTmp, HFreeAllTmp,

HAllocRLTmp, HAllocRLNumTmp, HFreeRLTmp

Synopsis

#include "Halcon.h"

Herror HAllocTmp( Hproc_handle proc_handle,

void **pointer,
size_t size)

Herror HFreeTmp( Hproc_handle proc_handle,

void *pointer)

Herror HFreeUpToTmp( Hproc_handle proc_handle,

void *pointer)

Herror HFreeAllTmp( Hproc_handle proc_handle)

Herror HAllocRLTmp( Hproc_handle proc_handle,

Hrlregion **region)

Herror HAllocRLNumTmp( Hproc_handle proc_handle,

Hrlregion **region,
size_t size)

Herror HFreeRLTmp( Hproc_handle proc_handle,

Hrlregion *region)

Figure 3.1: HALCON stack management for temporary data.

Figure 3.1 shows HALCON routines to allocate/deallocate temporary memory blocks. Internally, those blocks are
stored within a stack. Therefore, the memory must be deallocated in reverse order of it’s allocation. There are two
major advantages of using these routines:

• The underlying stacks are initially allocated as large blocks of memory. Thus, the memory is not fragmented
and memory allocation is fast for subsequent calls.
42 Style Guide for Programming

• An automatic garbage collection deallocates all temporary data after a HALCON operator was executed.
This is especially of importance in case of an error during the execution of the operator (otherwise, the data
should have been deallocated anyway).

HAllocTmp is used for arbitrary data with the corresponding deallocation routine HFreeTmp. HFreeUpToTmp
deallocates all recently allocated blocks up to (and including) the specified block. HFreeAllTmp deallocates all
temporary blocks.
HAllocRLTmp and HAllocRLNumTmp are convenience routines that are based on HAllocTmp. HAllocRLTmp
allocates as much memory as is necessary for the largest region currently stored in the HALCON database of
iconic objects (the minimal size is DEF_RL_LENGTH = 50000 chords). Using HIncrRL (section 5.6.5 on page
84), HAllocRLTmp allocates more memory. HAllocRLNumTmp allows you to determine the size of memory to be
allocated by specifying the number of chords. Furthermore, HAllocRLTmp and HAllocRLNumTmp initialize the
data structure Hrlregion for the new region (see section 4.2 on page 50 for a description of Hrlregion). Note
that since these routines are based on HAllocTmp the corresponding memory blocks are interleaved with the blocks
allocated directly via HAllocTmp. This has to be considered while deallocating the corresponding memory.

Temporary data on arbitrary heap positions

Names

HAllocLocal, HReallocLocal, HFreeLocal,

HAllocRLLocal, HAllocRLNumLocal, HReallocRLNumLocal, HFreeRLLocal

Synopsis

#include "Halcon.h"

Herror HAllocLocal( Hproc_handle proc_handle,

size_t size,
void **pointer)

Herror HReallocLocal( Hproc_handle proc_handle,

void *pointer
size_t size,
void **new_pointer)

Herror HFreeLocal( Hproc_handle proc_handle,

void *pointer)

Herror HAllocRLLocal( Hproc_handle proc_handle,

Hrlregion **region)

Herror HAllocRLNumLocal( Hproc_handle proc_handle,

Hrlregion **region,
size_t num)

Herror HReallocRLNumLocal( Hproc_handle proc_handle,

Hrlregion *region
size_t num_new,
Hrlregion **new_region)

Herror HFreeRLLocal( Hproc_handle proc_handle,

Hrlregion *region)

Figure 3.2: Temporary data on arbitrary heap positions.

The temporary data management routines described so far use a stack. This is of advantage concerning runtime,
but it lacks flexibility if you do not want to deallocate memory in a fixed order again. Therefore, HALCON also
provides routines for allocating temporary memory on an arbitrary position of the heap, see figure 3.2. Memory
blocks allocated by HAllocLocal can be deallocated by HFreeLocal in an arbitrary order. However, similar
 3.2.2 Global Data 43

to the stack-based temporary data management, all these blocks are automatically deallocated at the end of a
HALCON operator. Again this mainly aims on preventing memory leaks in case of errors. As usual, the routine
HReallocLocal is used to allocate a new memory block with modified size while preserving the data of the
original memory block. The latter is deallocated. So never try to access pointer subsequent to HReallocLocal–
use new_pointer exclusively.
The convenience routines HAllocRLLocal , HAllocRLNumLocal HReallocRLNumLocal, and HFreeRLLocal
are used for handling temporary region data based on HAllocLocal. Otherwise their behavior is similar to
HAllocRLTmp etc., see above. E.g., using HIncrRL (section 5.6.5 on page 84), HAllocRLLocal allocates more
memory. However, note that it is possible to change the size of regions (i.e., the number of chords) using this set of
routines (HReallocRLNumLocal) since the underlying memory blocks are not allocated within the internal stacks.

Handle Data

Name

HAllocOutputHandle

Synopsis

Style Guide
#include "Halcon.h"

Herror HAllocOutputHandle( Hproc_handle proc_handle,

int par,
Hphandle elem,
H_HANDLE_TYPE HHandleInfo)

Figure 3.3: Memory management for handles.

The routine HAllocOutputHandle allocates one handle in the output control parameter par. HHandleInfo holds
handle type information. elem is modified to point to where the new tool can be allocated.
The output control variable gains ownership of the pointer in elem. When aborting an operator with an error,
the value must not be cleared inside the operator’s code, but will be cleared automatically when cleaning the output !
control variable.

3.2.2 Global Data

The HALCON Extension Package Interface also provides routines for globaly allocating/deallocating memory
(see figures 3.4 and 3.5). They work similar to the standard C procedures malloc and free, but use a caching
mechanism for small data blocks and provide additional debugging information.
Note that in contrast to HAllocLocal, memory allocated by HAlloc is not deallocated automatically after the
execution of a HALCON operator. Thus, this routine should be used to allocate global data. For example, all the
iconic objects stored in the HALCON database of iconic objects are allocated with this routine (see chapter 5 on
page 57 and chapter 6 on page 87).

HNewImage allocates raw image data inside1 the data structure Himage (see section 4.1 on page 49) based on
HAlloc. Furthermore, image is initialized and the timestamp is set to the current time. The image matrix itself is
initialized with 0 if ’init_new_image’ has been set to ’true’ using the HALCON operator set_system. This
flag can be read inside HALCON using the Extension Package Interface call HReadGV.

HReadGV(proc_handle, HGInitNewImage, &init_new_img);

with init_new_img of type bool and set

HWriteGV(proc_handle, HGInitNewImage, {true,false});

1 So HNewImage does not allocate memory for the Himage structure itself.
44 Style Guide for Programming

Names

HAlloc, HRealloc, HFree, HNewImage, HNewImagePtr,

HAllocXLDCont, HFreeXLDCont

Synopsis

#include "Halcon.h"

Herror HAlloc( Hproc_handle proc_handle,

size_t size,
void **pointer)

Herror HRealloc( Hproc_handle proc_handle,

void *pointer
size_t size,
void **new_pointer)

Herror HFree( Hproc_handle proc_handle,

void *pointer)

Herror HNewImage( Hproc_handle proc_handle,

Himage *image,
int kind,
HIMGDIM width,
HIMGDIM height)

Herror HNewImagePtr( Hproc_handle proc_handle,

Himage *image,
int kind,
HIMGDIM width,
HIMGDIM height,
void *data,
bool initImg)

Herror HAllocXLDCont( Hproc_handle proc_handle,

Hcont **cont,
HITEMCNT num_points)

Herror HFreeXLDCont( Hproc_handle proc_handle,

Hcont *cont)

Figure 3.4: General memory management within HALCON.

Thus, it is possible to buffer the global setting of this flag, set the flag to false prior to HNewImage, and restore
the old value afterward, if you would like to prevent an initialization in any case.
HNewImagePtr does not allocate memory for the image data, but inserts the pointer data in the Himage structure
image instead. For this routine, the initialization of the image data is controlled via the parameter initImg. Note
that you will encounter program crashes during deallocation of image objects, if you insert a memory block that
has not been allocated via HAlloc in the underlying Himage structure (see, for example, HPutImage in section 5.4
on page 67).
For both HNewImage and HNewImagePtr the pixel type of the raw data within image is specified by the parameter
kind. Please see figure 4.2 on page 50 for the supported values.

HAllocXLDCont allocates an XLD contour2 of type Hcont (see section 4.3 on page 52) including memory for
num_points contour points. Internally this routine is based on HAlloc. HFreeXLDCont is used to deallocate a
contour again (including all the points and all attributes defined for cont, see page 54).
2 In contrast to HNewImage and HNewImagePtr HAllocXLDCont also allocates memory for the structure Hcont itself, not only for the data

inside that structure.

 3.2.3 Debugging 45

Names

HAllocRL, HAllocRLNum, HReallocRLNum, HFreeRL

Synopsis

#include "Halcon.h"

Herror HAllocRL( Hproc_handle proc_handle,

Hrlregion **region)

Herror HAllocRLNum( Hproc_handle proc_handle,

Hrlregion **region,
size_t len)

Herror HReallocRLNum( Hproc_handle proc_handle,

Hrlregion *region
size_t len,
Hrlregion **new_region)

Style Guide
Herror HFreeRL( Hproc_handle proc_handle,
Hrlregion *region)

Figure 3.5: General memory management for region data.

The convenience routines HAllocRL , HAllocRLNum, HReallocRLNum, and HFreeRL (see figure 3.5) are used for
handling global region data based on HAlloc. Otherwise, their behavior is similar to HAllocRLTmp etc. E.g.,
using HIncrRL (section 5.6.5 on page 84), HAllocRL allocates more memory, see page 42. Note that it is possible
to change the size of regions (i.e., the number of chords) using HReallocRLNum.

3.2.3 Debugging

The HALCON memory management provides debugging mechanisms. The debugging is enabled with set_check
(’memory’), and can be switched off with set_check(’~memory’). Every time a memory block is deallocated
a couple of consistency checks are performed automatically. Moreover, the consistency of memory blocks can be
checked for debugging reasons at any time using specific Extension Package Interface routines, see figure 3.6.

Names

HTestMem, HTestPtr, HTestAllTmp, HTestTmp

Synopsis

#include "Halcon.h"

Herror HTestMem( void)

Herror HTestPtr( void *pointer)

Herror HTestAllTmp( Hproc_handle proc_handle)

Herror HTestTmp( Hproc_handle proc_handle,

void *pointer)

Figure 3.6: HALCON memory management: Check of consistency.

HTestMem checks all the memory allocated with HAlloc or HAllocLocal, whereas HTestPtr checks only the
specified memory block, which must have been allocated with HAlloc. Similar to that, HTestAllTmp checks
46 Style Guide for Programming

all the memory allocated via HAllocTmp, and HTestTmp checks the specified block. With any failure of the
consistency check, the routines return an error code (H_ERR_ICM – inconsistent memory). Furthermore, if the
global variable HDoLowError is set to true, they display a description of the error either on stderr (Unix-like
systems) or within an alert box (Windows). This variable can be set in an application with the operator set_system
("do_low_error","true"/"false") or used directly inside the newly written operator.

3.3 Structuring Programs

HALCON operators are typically implemented by at least two routines: one procedure (supply procedure) re-
ceives/unpacks all input data and checks its consistency. Afterward, it calls the action procedure, which performs
the image processing. In some cases, it can be convenient to implement several action procedures dependent on
special parameter values or pixel types of image data. Generally, these steps are performed within a loop over all
input iconic objects that may include further loops over different parameter values and over all image channels.
The results are collected and finally returned to the HALCON interface to the application.
Supply procedures are of type Herror and have only one parameter (a handle of type Hproc_handle for instances
of HALCON operators or HALCON threads). Do not forget to return an appropriate value at the end of every
supply procedure (standard value: H_MSG_TRUE) and every action procedure (standard value: H_MSG_OK).
Typically, action procedures perform the image processing itself. They should return an error code of type Herror
as well. It is convenient to implement an action procedure for each pixel type of image data.

3.4 Extension Package Initialization

To initialize an extension package, the following optional function may be defined:

extern HUserExport Herror HXPkgMain(Hproc_handle)

If defined, HALCON will call this function upon loading the extension package. For example, this mechanism is
useful to initialize synchronization objects (for example, mutexes) that will be used in the extension package.

3.5 Name Conventions for Procedures

To ease the interpretation of program code, HALCON introduces some conventions for procedure names. The
most important ones are summarized in the following section.
The names of action procedures typically begin with “IP” (image processing procedure), “IO” (input/output pro-
cedure), or “DB” (data base procedure). The rest of the name describes the task performed by the procedure (in
English language, beginning with a capital letter). In case of filters an additional token might be inserted between
these two parts of the name encoding the pixel type(s) of images to be processed, for example, “B” (HBYTE), “I4”
(INT4) or “F” (float).
Examples:
IPBLowpas
IPI4Threshold
IODispRegion
DBGetTuple
Basic routines performing a small task that might be used by many other routines should start with “H” (for Help).
The leading “H” should be followed by a string encoding the data the routine works on, for example, “RL” for an
auxiliary routine processing region data, or “XLD” for routines working on XLDs.
Examples:
HRLUnion
HXLDContLen
HXLDContRegress
 3.6 Input / Output 47

Names of supply procedures start with “C” (this stands for Core). The rest is determined by the name of the
underlying action procedure (if there is only one). If there are several action procedures with names differing only
by the symbols for different pixel types, the pixel type is left out in the name of the supply procedure.
Examples:
CIPLowpas
CIPThreshold
CIOOpenWindow

3.6 Input / Output

Except explicit IO routines HALCON procedures should not contain any input/output commands, especially no
print commands. Any interaction should be done either via parameters or via Extension Package Interface in-
/output procedures. Error messages should be encoded by proper error code returned by the procedure (see next
section).

3.7 Error Handling

Style Guide
3.7.1 Defining Own Error Codes

Error messages are represented by integer constants, the error codes of type Herror. If an error occurs, the
corresponding error code should be returned by the procedure.
The file %HALCONROOT%\include\HErrorDef.h contains predefined error messages for all typical errors, see
also appendix A on page 105. It may still happen that none of them fits an error occurring in a new, user-defined
operator. Therefore, you can define new codes, which should be greater than 10 000 to avoid re-using an already
allocated code or a code reserved for future extensions of the HALCON system. If the user-defined operator returns
a user-defined error, the error will be reported as

No error message available for this error code (<error code>) .

In order to provide user-defined errors with error messages, the function HSetErrText

Herror HSetErrText(char *error_message)

can be called immediately before the operator returns the error code with return H_ERR_*. In this case, the error
message error_message will be displayed by the next call of the HALCON operator get_error_text. Within
this call, the error message is reset to “No error message available ...” again to ensure that the user-defined error
message is up to date.
Error codes are specified via #define and are called H_ERR_XYZ.
Examples:
H_ERR_WIPN1 /* wrong number of values in input control */
/* parameter 1 */
H_ERR_WIPV3 /* wrong parameter value (control param. 3) */
H_ERR_WIPT2 /* wrong type of values (control param. 2) */
H_ERR_WION1 /* wrong number of objects in input object */
/* parameter 1 */
H_ERR_WIT /* wrong image type */
H_MSG_TRUE /* no error (supply procedure) */
H_MSG_OK /* no error (any other procedure) */
All HALCON procedures return an error code. This code has to be checked after calling any HALCON procedure,
for example, by encapsulating the procedure call in the macro HCkP. This macro checks the return value and exits
the current procedure if an error occurred (a detailed description of the macro is given in the section 5.6.1 on
page 83). Please note that some of the Extension Package Interface macros described in chapter 5 on page 57 and
chapter 6 on page 87 (for example, HGetCPar) implicitly use the macro and therefore automatically return a proper
error code.
48 Style Guide for Programming

3.7.2 Extending Error Codes

There is also a mechanism to add some extended error information about the thread’s current HALCON error. The
function HSetExtendedErrorInfo

Herror HSetExtendedErrorInfo(Hproc_handle proc_handle, INT4_8 error_code,

char const *error_message)

can be called immediately before the operator returns the error code with return H_ERR_*. In this case, the
extended error information (error_code and error_message) will be set thread-locally and can be queried by
the next call of the HALCON operator get_extended_error_info. The set information gets cleared by both
the next occurring HALCON error or the next call of HSetExtendedErrorInfo.
In error_code, a user-defined error code can be set, for example, a third-party SDK error code or a 0 value
(indicating that no extended error code is set).
In error_message, a user-defined error message can be specified, for example, a third-party SDK error message
or an empty string "" (indicating that no extended error message is set).
When HSetExtendedErrorInfo is called, it creates a copy of the error message. This means that you do not have
to ensure the input remains valid after the function has been called. For example, apart from a string literal, you
can also use a dynamically generated value for error_message.
Instead of HSetExtendedErrorInfo, you can also use the function HSetExtendedErrorInfoF

Herror HSetExtendedErrorInfoF(Hproc_handle proc_handle, INT4_8 error_code,

char const* error_message, ...)

which allows you to use printf-like formatting of the error_message.

An example showing how to use HSetExtendedErrorInfo is provided in the file
$HALCONEXAMPLES/extension_package/useropencl/source/CIPOpenCLFilter.c.
An example showing how to obtain the extended error information by means of get_extended_error_info is
provided in $HALCONEXAMPLES/extension_package/useropencl/examples/testuseropencl.hdev.

3.8 Notes on Image Processing Operators

• HALCON images are variable in their size (format). Therefore, no constants should be used for image
formats (except MAX_FORMAT for the maximum format). The actual format of an image can be extracted
from the structure Himage (cf. figure 4.1 on page 50).
• Notice that more than one pixel type may occur, when performing gray value operations. An operator should
be able to work on all of them, see also the discussion in section 6.1.3 on page 90. If an operator can only
process a reduced set of types, this can be specified in the DEF file with type_list (cf. page 32). An
operator should reject all images that it can not process by returning H_ERR_WIT – wrong image type.
• In many cases an operator might receive more than one iconic object as input, i.e. the supply procedure must
contain a loop over all iconic objects (for example, using HAllReg and HAllSegm described in section 6.1
on page 87 or HAllObj in section 5.3.1 on page 66). This is true for regions as well as images or XLDs.
Furthermore, images may contain more than one channel. So a second loop over all channels (components)
within an image is needed (see HAllComp, section 5.3.2 on page 66).
• All procedures should only work within the image’s area of definition, especially when performing feature
extraction, filter or segmentation tasks.
 HALCON Data Types 49

Chapter 4

HALCON Data Types

The HALCON Extension Package Interface provides special data types to handle iconic objects. All iconic objects
in the application layer are represented by a key referring to the HALCON database of iconic objects. The internal
structure is hidden from the HALCON user. However, using the Extension Package Interface it is possible to work
directly on the data structures for images, regions, and XLDs. Special macros can be used to access the internal
representation of such an iconic object. Furthermore, data structures for control parameters are provided. All
data types described in the following sections are defined in the files %HALCONROOT%\include\IPType.h and
%HALCONROOT%\include\HBase.h.

4.1 Pixel Data (Himage)

Data Types
Gray value images are represented by a rectangular image matrix. Several matrices (called channels) can be
combined to a multi-channel image. Each channel can be accessed separately, i.e. the channels are not interleaved.
The structure Himage contains size, pixel type, and pixel data of one channel. Furthermore, a time-stamp is
included. Figure 4.1 shows the corresponding type declaration.
The maximum for width and height, which describe the image size, is determined with MAX_FORMAT (HALCON:
32 768, HALCON XL: 1 073 741 824). The origin of an image matrix is at position (0, 0). Row coordinates range
from 0 to height - 1, column coordinates from 0 to width - 1. The image pointer (HPixelImage) refers to
the first pixel of the matrix (index: 0,0). Different pixel types are supported. They are distinguished by a selector
(kind), see figure 4.2. The pixel types include basic types like uint8_t, int8_t, int32_t, and float as well as
composed types. Their definitions can be seen in figure 4.3.
The pixel data is stored as a one-dimensional array (image vector) of one of the pixel types. The indices of the
array range from 0 to width*height-1. A linear coordinate L within an image is derived from the row index R
and column index C as follows:

L = R * image.width + C

This transformation is performed by the following macro HLinCoor:

L = HLinCoor(R,C,image.width);

There are two additional macros for computing rows (HRow) and columns (HCol):

R = HRow(L,image.width);
C = HCol(L,image.width);

Please see section 3.2.2 on page 43 for routines to allocate image data within Himage.
50 HALCON Data Types

typedef union {
uint8_t* b; /* 0..255 (BYTE_IMAGE) */
uint8_t* z; /* 0..255 mod 256 (CYCLIC_IMAGE) */
uint8_t* d; /* orientation 0..180 (DIR_IMAGE) */
int8_t* i; /* -128..127 (INT1_IMAGE) */
int32_t* l; /* 4 byte integer (LONG_IMAGE) */
int64_t* i8; /* 8 byte integer (INT8_IMAGE) */
float* f; /* 4 byte real (FLOAT_IMAGE) */
HVFPixel* vf; /* vector field (VF_IMAGE) */
HComplexPixel* c; /* complex image (COMPLEX_IMAGE) */
HInt2Pixel s; /* 2 bytes with sign (INT2_IMAGE) */
HUInt2Pixel u; /* 2 bytes without sign (UINT2_IMAGE) */
} HPixelImage;

typedef struct {
int kind; /* pixel type */
HPixelImage pixel; /* pixel data */
HIMGDIM width; /* image width */
HIMGDIM height; /* image height */
HImageFreeProc free_proc; /* function for deallocating image data */
bool free; /* free image data when deleting image */
/* time of creation of image */
uint16_t msec; /* milliseconds 0..999 */
uint8_t sec; /* seconds 0..59 */
uint8_t min; /* minutes 0.59 */
uint8_t hour; /* 0..23 */
uint8_t day; /* 1..31 */
uint16_t yday; /* 1..366 */
uint8_t mon; /* 1..12 */
uint16_t year; /* 19xx */
} Himage;

Figure 4.1: Data type Himage for images.

#define BYTE_IMAGE (int)1 /* 1 byte per pixel (0..255) */

#define INT4_IMAGE (int)2 /* Type: 4 bytes per pixel (int32_t) */
#define LONG_IMAGE (int)2 /* 4 byte per pixel (int32_t) */
#define FLOAT_IMAGE (int)4 /* 4 byte per pixel (float) */
#define DIR_IMAGE (int)8 /* edge orientation 0..180 */
#define CYCLIC_IMAGE (int)16 /* 0..255 cyclic */
#define INT1_IMAGE (int)32 /* -128..127 */
#define COMPLEX_IMAGE (int)128 /* 2 float images */
#define INT2_IMAGE (int)512 /* 2 bytes with sign */
#define UINT2_IMAGE (int)1024 /* Type: 2 bytes (unsigned short) */
#define VF_IMAGE (int)2048 /* Two float images */
#define INT8_IMAGE (int)4096 /* 8 byte per pixel (int64_t) */

Figure 4.2: Definitions of pixel types.

4.2 Region Data (Hrlregion)

In HALCON region data is represented by a special variant of the runlength encoding – a chord encoding: For
every line (chord) of a region its row index (“y coordinate”,“line number”) and the column index (“x coordinate”)
of its start and end point is stored. Both the start point and the end point belong to the region.
Chord data must fulfill the following conditions:

• a chord is limited to one row

• chords may not overlap
 4.2 Region Data (Hrlregion) 51

typedef struct {
float re; /* real image part */
float im; /* imaginary image part */
} HComplexPixel;

typedef struct {
int16_t* p; /* gray values */
int8_t num_bits; /* number of used bits */
} HInt2Pixel;

typedef struct {
uint16_t* p; /* gray values */
int8_t num_bits; /* number of used bits */
} HUInt2Pixel;

typedef struct {
float* row; /* row direction */
float* col; /* column direction */
} HVFPixel;

Figure 4.3: Data types for Himage.

• chords are sorted in ascending order

If a region is read from the HALCON database of iconic objects, its representation fulfills all the conditions above.
When writing a region, condition 2 and 3 need not to be sufficed in all cases, as the Extension Package Interface
automatically modifies the data (at cost of computation time).

Data Types
typedef struct {
HIMGCOOR l; /* line number (row) of run */
HIMGCOOR cb; /* column index of beginning of run */
HIMGCOOR ce; /* column index of ending of run */
} Hrun;

typedef struct {
bool is_compl; /* region is complement */
HITEMCNT num; /* number of runs */
HITEMCNT num_max; /* maximum number of runs */
HRegFeature feature; /* already processed features */
Hrun* rl; /* pointer on array of run lengths */
} Hrlregion;

Figure 4.4: Data type Hrlregion for region encoding.

Figure 4.4 shows the type declaration for chords. In the structure Hrlregion, all chords are stored in an array of
the type Hrun, where num is the current and num_max the maximum allowed number of chords (depending on the
size of the region specified at its creation, see also section 3.2 on page 41). The flag is_compl allows an easy
transformation of a region in its complement. Operators that work on regions must consider this flag and react
according to its value. The structure HRegFeature (see figure 4.5) contains all region shape features extracted so
far to avoid repeating a computation. HFeatureFlags encodes, which features already have been extracted. Do
not forget to reset these flags if you modify a region.
Normally, a variable of type Hrlregion is allocated with the procedure HAllocRLTmp or HAllocRLNumTmp, see
section 3.2 on page 41. These routines initialize the data, especially num_max that is needed for tests of overflow.
When allocating a variable “by hand”, the programmer must provide a suitable initialization by himself/herself.
Whereas all coordinates within runlength codes are stored as (row,column), linear coordinates are used to address
HALCON image matrices. Thus, the macros CB and CE are very helpful, especially when processing gray values
(in linear coordinates) along a chord. The programs in figure 6.5 on page 91 and figure 6.7 on page 93 illustrate
how to use them. Their functionality can be seen in figure 4.6. The first parameter (rl) contains a pointer to the
chords as it is used within Hrlregion. index specifies the index of the chord to work on and width contains the
image width. CB returns the linear coordinate of the start point and CE that of the end point of the chord.
52 HALCON Data Types

typedef struct {
union {
HFeatureFlags single;
long all; /* if possible use 64 bits!
} def;
uint8_t shape; /* SHAPE_*
bool is_convex;
bool is_filled;
bool is_connected4;
bool is_connected8;
bool is_thin; /* one pixel thin
double circularity;
double compactness;
double contlength;
double convexity;
double phi;
double ra, rb; /* elliptic_axis
double ra_, rb_; /* elliptic_shape
double anisometry, bulkiness, structure_factor;
double m11, m20, m02, ia, ib;
double row, col;
HIMGCNT area;
HIMGCOOR row1, col1, row2, col2;
double row_rect, col_rect, phi_rect, length1, length2;
double row_circle, col_circle, radius;
HIMGCOOR min_chord, max_chord;
HIMGCOOR min_chord_gap, max_chord_gap;
double rectangularity;
} HRegFeature;

Figure 4.5: Data type HRegFeature for region shape features.

Names
CB, CE

Synopsis
#include "Halcon.h"

HLINCOOR CB(Hrun* rl,

HITEMCNT index,
HIMGDIM width)

HLINCOOR CE(Hrun* rl,

HITEMCNT index,
HIMGDIM width)

Figure 4.6: Linear coordinates from Hrlregion.

4.3 XLDs (Hcont, Hpoly)

XLDs (eXtended Line Descriptions) are specific iconic HALCON objects to represent subpixel accurate contours
and polygons. The corresponding data types Hcont and Hpoly are listed in figures 4.7 and 4.8.
HALCON contours of type Hcont contain an array of subpixel points along a contour. A contour might be clas-
sified concerning to topological considerations (cont_class). Additionally, an arbitrary number of additional
contour attributes for each point along the contour can be included (attribs), for example, the edge amplitude
of subpixel edge points or the orientation of the local gradient. Finally, an arbitrary number of additional global
attributes, i.e., attributes valid for the entire contour, can be included (global), for example, the individual param-
eters of a regression line to the contour or the parameters of an ellipse segment fitted to the contour.
 4.3 XLDs (Hcont, Hpoly) 53

typedef enum cont_class {

cont_unknown, /* unknown */
cont_no_junc, /* neither start nor end point points */
/* are junctions */
cont_start_junc, /* start point is a junction */
cont_end_junc, /* end point is a junction */
cont_both_junc, /* both start and end point are junctions */
cont_closed /* closed contour */
} Hcont_class;

typedef struct cont_attrib {

char *name; /* name of the attribute */
HSUBATTR *val; /* value of the attribute (per point) */
} Hcont_attrib;

typedef struct cont_global_attrib {

char *name; /* name of the global attribute */
HSUBATTR val; /* value of the attribute (per contour) */
} Hcont_global_attrib;

typedef struct cont_type {

HITEMCNT num; /* number of points along the contour */
HSUBCOOR* row; /* points / row indices (y coordinates) */
HSUBCOOR* col; /* points / column indices (x coord.) */
Hcont_class cont_class; /* contour class */
int32_t num_attrib; /* number of additional attributes */
Hcont_attrib* attribs; /* additional attributes (for each point) */
int32_t num_global; /* number of additional global attributes */
Hcont_global_attrib* global;/* additional attributes (per contour) */
int32_t h; /* auxiliary (temporary) */

Data Types
} Hcont;

Figure 4.7: The XLD data type Hcont for subpixel contours.

typedef struct lin_seg_type {

HSUBCOOR row,col; /* a control point of the polygon: */
/* row (y) and column (x) coordinate */
HSUBATTR length; /* length of the line from the */
/* current to the next point */
HSUBATTR phi; /* orientation (rad) of this line */
Hkey ref; /* database key of the underlying */
/* contour */
HITEMCNT first; /* index of the first point of the */
/* underlying contour belonging to */
/* current side of the polygon */
HITEMCNT last; /* index of the last contour point */
} Hline_seg;

typedef struct poly_type {

HITEMCNT num_line; /* number of lines */
HITEMCNT len_line; /* maximum number of lines (size */
/* of the array lines) */
Hline_seg* lines; /* control points of the polygon */
} Hpoly;

Figure 4.8: The XLD data type Hpoly for subpixel polygons.

Please see section 3.2.2 on page 43 for routines to allocate/deallocate contours. Two important auxiliary rou-
tines to copy contours are listed in figure 4.9 on page 54. HCopyXLDCont copies a complete contour, whereas
HCopyXLDContPart copies only a part of the original contours specified by two indices min_index and
max_index. They refer to the first and the last point along the contour to be copied (starting with index 0).
54 HALCON Data Types

Names

HCopyXLDCont, HCopyXLDContPart

Synopsis

#include "Halcon.h"

Herror HCopyXLDCont( Hproc_handle proc_handle,

Hcont* cont_in,
bool preserve_attribs,
bool preserve_global_attribs,
Hcont** cont_out)

Herror HCopyXLDContPart( Hproc_handle proc_handle,

Hcont* cont_in,
INT4_8 min_index,
INT4_8 max_index,
bool preserve_attribs,
bool preserve_global_attribs,
Hcont** cont_out)

Figure 4.9: Auxiliary routines for contours of type Hcont.

Names
HAddXLDContAttrib, HLookupXLDContAttrib,
HAddXLDContGlobalAttrib, HLookupXLDContGlobalAttrib

Synopsis
#include "Halcon.h"

HAddXLDContAttrib( Hproc_handle proc_handle,

Hcont* cont,
char* name,
int32_t* index)

HLookupXLDContAttrib( Hcont* cont,

char* name,
int32_t* index)

HAddXLDContGlobalAttrib( Hproc_handle proc_handle,

Hcont* cont,
char* name,
int32_t* indx);

HLookupXLDContGlobalAttrib( Hcont* cont,

char* name,
int32_t* indx);

Figure 4.10: Handling contour attributes of contour pixels (within Hcont).

For closed contours a negative value might be specified for min_index. This will lead to a “wrap-around”,
that is the part of the contour to be copied starts at cont_in->num + min_index. Both HCopyXLDCont and
HCopyXLDContPart allocate the output contour themselves. So just pass a pointer to a pointer to Hcont with-
out allocating any memory for cont_out. Both routines provide two additional parameters, preserve_attribs
and preserve_global_attribs, to control whether the non-global and the global contour attributes should be
copied.
The routines provided for handling contour attributes of contour points are summarized in figure 4.10.
HAddXLDContAttrib is used to add a new class of contour attributes to a given contour cont. Note that this
routine allocates memory for the attribute values, but it does not set the values themselves. An arbitrary name for
 4.4 Control Parameters 55

the attribute can be specified by the parameter name. The index of the new attribute within the attribs array
in cont is returned in index and can be used to address the values by cont->attribs[index].val[xxx].
The same holds for global attributes: HAddXLDContGlobalAttrib is used to add new global attributes,
which can be accessed by cont->global[index].val. Note that these values can be accessed within
the HALCON system (that is on the application layer) using the operators get_contour_attrib_xld and
get_contour_global_attrib_xld. See the Reference Manuals for details. Within HALCON, a specific at-
tribute of a contour can be accessed using HLookupXLDContAttrib, while a specific global attribute can be
accessed using HLookupXLDContGlobalAttrib. These routines return the index of the desired attribute within
attribs or global of cont, or the error code H_ERR_XLD_CAND as result of the procedure call, if no attribute
with the specified name is defined.
The XLD data type Hpoly, displayed in figure 4.8 on page 53, encodes subpixel accurate polygons. Basically it
contains an array of control points. In many applications such polygons are derived from contours. Thus, the data
structure can also hold a reference to the underlying part of a contour specified by a HALCON database key.

4.4 Control Parameters

typedef union {
INT4_8 l; /* 4/8 byte integer */
double d; /* 8 byte real */
char* s; /* string */
Hphandle H; /* Pointer to handle */
} Hpar;

typedef struct {
Hpar par;
int type;

Data Types
} Hcpar;

Figure 4.11: Data types Hpar and Hcpar for control parameters.

HALCON’s basic and essential view on control data are arrays. These arrays are used to pass control parameter
values to supply procedures and can assume five different types, four basic or a mixed type, see section 2.3 on page
28.
Basic types are supported INT4_8 arrays, coded as LONG_PAR, double arrays coded as DOUBLE_PAR, handle
arrays coded as HANDLE_PAR, and string arrays, i.e., char* arrays, coded as STRING_PAR. Note that all
strings passed to and from the HALCON library must be encoded in UTF-8. The legacy encoding mode
(set_system(’filename_encoding’,’locale’) is not supported for extension packages that use strings with
non-ASCII characters.
The structure Hcpar enables HALCON to pass a mixed type (MIXED_PAR), holding any of the basic types in the
union Hpar, encoded by the specifyer type. Figure 4.11 shows the corresponding definitions. Thus, it is possible
to pass a native array type or to combine different types within an array of Hcpar values. For it, the selector type
must be set to one of the basic type codes LONG_PAR, DOUBLE_PAR, HANDLE_PAR or STRING_PAR.
The Extension Package Interface procedures described in section 5.5 on page 72 are used to access the control
parameters of HALCON operators and pass the control data arrays through the interface.
56 HALCON Data Types
 Handling Iconic Objects and Control Parameters 57

Chapter 5

Handling Iconic Objects and Control

Parameters

The HALCON Extension Package Interface provides a large set of procedures and macros for handling control
parameters and iconic objects. It supports tasks like:

• Accessing iconic input objects in the HALCON database.

• Accessing single iconic objects within a tuple of objects.
• Accessing specific components (regions, gray value channels) of image objects.

• Accessing XLDs.
• Creating iconic output objects in the HALCON database based on the computed results.
• Reading input control parameters.
• Writing output control parameters.

Parameter Handling
The routines of the Extension Package Interface described in this and the following chapter especially facilitate the
programming of support procedures (that is the access of the HALCON database and all the parameter handling).
In this chapter the “low level” interface routines are introduced. They allow a straightforward access to all param-
eters of an operator – to iconic objects (and their components) and to control parameters. Moreover, some routines
for creating iconic objects and writing output iconic parameters and control parameters are introduced.
Based on these low level routines a set of convenience routines are presented in chapter 6 on page 87. They are
designed to further facilitate the programming of very typical support procedures.

5.1 Basic Access to Iconic Input Objects

This section introduces some basic routines for accessing iconic objects (regions, gray value channels, XLDs), see
figure 5.1. They form a basic interface to the HALCON database of iconic objects. Figure 5.2 illustrates how they
are used to read image and region data from input iconic parameters.

5.1.1 HGetObj

HGetObj (see figure 5.1) returns the database key (type: Hkey) of an iconic object corresponding to the input
object parameter with the index par_num of the HALCON operator.
Note that HGetObj automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HGetObj yourself.
!
58 Handling Iconic Objects and Control Parameters

Names

HGetObj, HGetComp, HGetRL, HGetImage, HGetXLD

Synopsis

#include "Halcon.h"

HGetObj( Hproc_handle proc_handle,

int par_num,
INT4_8 obj_num
Hkey *obj_key)

HGetComp( Hproc_handle proc_handle,

Hkey obj_key,
int comp
Hkey *comp_key)

HGetRL( Hproc_handle proc_handle,

Hkey region_key,
Hrlregion *region)

HGetImage( Hproc_handle proc_handle,

Hkey image_key,
Himage *image)

HGetXLD( Hproc_handle proc_handle,

Hkey obj_key,
int xld_type,
Hpoly|Hcont **xld)

Figure 5.1: Basic routines for accessing iconic input objects.

operator call

1st input object parameter 2nd input object parameter

1st input object parameter

parameter number
1st object Hkey
of 1st input object parameter HGetObj obj_key
HGetComp Hkey comp_key
region channel1 channel2

HGetImage Himage
image
HGetRL Hrlregion
region

Figure 5.2: Direct access to input image objects.

The iconic object can either be a region (iconic object that contains only a region component), an image (iconic
object that contains a region component and one or more image channels), or an XLD (iconic object that contains
 5.1.2 HGetComp 59

int8_t inp_pars;
int32_t num_objs;
int p,o;
Hkey key;
...
/* get number of input iconic parameters: */
/* note: This number is known in general - it is specified by */
/* the operator header in the corresponding DEF file of the */
/* operator */
HReadGV(proc_handle,HGinp_obj,&inp_pars);
for (p=1; p<=inp_pars; p++) {
/* get number of input iconic objects per input obj. parameter: */
HReadGVA(proc_handle,HGnum_obj,&num_objs,p);
for (o=1; o<=num_objs; o++) {
HGetObj(proc_handle,p,o,&key); /* get key of iconic object */
/* further processing ... */
}
}

Figure 5.3: Example for HGetObj: Database keys of all iconic objects of all input object parameters.

a contour or a polygon).
The parameters of a HALCON operator are numbered consecutively from 1 to n (not from 0 to n − 1) for each
parameter class (input/output iconic object/control). The parameter par_num of HGetObj refers to this index,
thus specifying the desired input iconic parameter. All objects passed within a single input iconic parameter are
numbered from 1 to m, with the first iconic object in the list having the index 1. The parameter obj_num of
HGetObj denotes the index of a desired iconic object within this list (1 ≤ obj_num ≤ m).
The total number of input iconic parameters for an operator is specified in the corresponding DEF file1 , but the
number of objects within an input iconic parameter is dynamic. This value is accessible via the Extension Package
Interface routine HReadGVA:

HReadGVA(proc_handle,HGnum_obj,&num_objs,p);

Parameter Handling
where p denotes the parameter index and num_objs is the desired number of iconic objects. As an alternative for
reading the number of iconic objects of an input iconic parameter without the routine HReadGVA, you can use the
macro HGetObjNum (see section 5.2.5 on page 65).
Note that a loop over all iconic objects passed to an operator within an input iconic object parameter is a very
common task. Therefore, HALCON provides a macro for this problem: See HAllObj in section 5.3.1 on page 66.

5.1.2 HGetComp

HGetComp (see figure 5.1 on page 58) returns the database key of an image component (image matrix, i.e., channel:
image_key or domain, i.e., area of definition: region_key) of an image object that is stored under the key
obj_key in the HALCON database of iconic objects.
Note that HGetComp automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HGetComp yourself.
All components of an iconic object are consecutively numbered from 0 to n, with 0 denoting the region (domain)
!
and 1 . . . n denoting the channels (image matrices). To get a better legibility of program code, the constants
REGION (= 0), IMAGE_INDEX (= 1), IMAGE1 (= 1), IMAGE2 (= 2), etc. have been defined globally and may be used
as parameter values.
The number of channels per image object obj_num of parameter par_num is accessible via HPNumOfChannels,
see figures 5.4 and 5.5:
1 So this number is actually known by the programmer. However, using HReadGV it can be read from the operator context as well, see

figure 5.3.
60 Handling Iconic Objects and Control Parameters

int obj_channels;
Hkey obj_key;
Hkey region_key;
Hkey image_key;
...
/* get key of object: */
HGetObj(proc_handle,p,o,&obj_key);
/* get key of region: */
HGetComp(proc_handle,obj_key,REGION,&region_key);
/* get number of channels: */
HCkP(HPNumOfChannels(proc_handle,p,o,&obj_channels));
for (i=1; i<=obj_channels; i++) {
/* get image matrix key: */
HGetComp(proc_handle,obj_key,i,&image_key);
/* ...further processing */
}

Figure 5.4: Example for HGetComp: Database keys of all regions and channels within an input image object.

Names

HPNumOfChannels

Synopsis

#include "Halcon.h"

Herror HPNumOfChannels( Hproc_handle proc_handle,

int par_num,
INT4_8 obj_num,
int *chn_num)

Figure 5.5: Auxiliary routine HPNumOfChannels .

HPNumOfChannels(proc_handle,par_num,obj_num,&obj_channels)

See also HNumOfChannels in section 5.6.4 on page 84 for a convenience version of this routine when dealing with
the first input iconic parameter. More examples of how to use HGetComp can be found in figure 5.6 on page 61 and
figure 5.7 on page 61.

5.1.3 HGetRL

HGetRL (see figure 5.1 on page 58) reads the runlength encoding of a region (type: Hrlregion, see section 4.2 on
page 50) denoted by the database key region_key (type Hkey) from the HALCON database.
Note that HGetRL automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HGetRL yourself.
Since the region data is copied to region, it might be overwritten with new values (in contrast to HGetImage and
HGetFDRL, cf. section 5.1.4 and section 5.2.2 on page 62). However, this means that enough memory for region
must be allocated before calling HGetRL, see section 3.2.1 on page 41.
Figures 5.6 and 5.7 show example applications of HGetRL.
 5.1.4 HGetImage 61

Hrlregion *region;
Hkey obj_key;
Hkey region_key;
...
HCkP(HAllocRLTmp(proc_handle,&region));
HGetObj(proc_handle,p,o,&obj_key);
HGetComp(proc_handle,obj_key,REGION,&region_key);
HGetRL(proc_handle,region_key,region);
/* processing (in general this should be done calling an action proc.) */
area = 0;
for (i=0; i<region->num; i++)
area += region->rl[i].ce - region->rl[i].cb + 1;
HCkP(HFreeRLTmp(proc_handle,region));

Figure 5.6: Example for HGetRL: Calculate the area of a region.

5.1.4 HGetImage

HGetImage (see figure 5.1 on page 58) reads the image data (type: Himage, see section 4.1 on page 49) of a
specific gray value component (i.e., channel) of an image object referenced by its database key (type Hkey) in the
HALCON database.
Note that HGetImage automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HGetImage yourself.
!
Hkey obj_key;
Hkey image_key;
Hkey region_key;
Himage image;
Hrlregion *region;
...
HGetComp(proc_handle,obj_key,IMAGE_INDEX,&image_key);
HGetComp(proc_handle,obj_key,REGION,&region_key);
HGetImage(proc_handle,image_key,&image);
HGetRL(proc_handle,region_key,region);

Parameter Handling
switch (image.kind) {
case BYTE_IMAGE:
/* processing (in general this should */
/* be done calling an action procedure) */
area = sum = 0;
for (c=0; c<region->num; c++) {
for (i=CB(region->rl,c,image.width);
i<=CE(region->rl,c,image.width); i++, area++)
sum += image.pixel.b[i];
}
average = sum / area;
break;
default: return(H_ERR_WIT); /* wrong image type */
}

Figure 5.7: Example for HGetImage: Average gray value of first channel.

The data structure Himage contains the gray values, the gray value type, and the size of the image matrix. Instead of
copying the image matrix, HGetImage only returns a pointer to the raw data in image.pixel. This is much more
efficient, but means that only read access to the image matrix is recommended (otherwise you will encounter
unpredictable side effects). Figure 5.7 shows an application of HGetImage. !
62 Handling Iconic Objects and Control Parameters

5.1.5 HGetXLD

HGetXLD (see figure 5.1 on page 58) is used to access XLD objects in the HALCON database of iconic objects. The
object of interest is specified by the database key obj_key. The parameter xld_type allows to specify the kind
of XLD data to be accessed: It has to be set to XLD_CONTOUR_ID in case of a contour and to XLD_POLYGON_ID in
case of a polygon. Corresponding to the selected type, HGetXLD expects a pointer to Hcont or a pointer to Hpoly
in the parameter xld. In both cases not the underlying data within the structures Hcont or Hpoly but only the
! pointers to the data are copied from the database. Thus, please avoid any write access to this data. Otherwise
you will encounter unpredictable side effects (changing other iconic objects). Figure 5.8 shows a simple example
for how to use HGetXLD.
Note that HGetXLD automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HGetXLD yourself.

Hkey obj_key;
Hcpar num_points;
Hcont *cont;

HGetObj(proc_handle,par_num,obj_num,&obj_key);
HGetXLD(proc_handle,obj_key,XLD_CONTOUR_ID,(void*)&cont);

/* processing (in general this should be done calling an action proc.) */

num_points.type = LONG_PAR;
num_points.par.l = cont->num;
HPutCPar(proc_handle,1,&num_points,1);

Figure 5.8: Example for HGetXLD: Return the number of points of the contour with the index obj_num within input
iconic parameter par_num.

5.2 Additional Routines for Accessing Input Image Objects

This section introduces some routines that ease the programming of supply procedures in many applications, see
figure 5.9. Basically they are combinations of the routines described in the previous section. These additional
routines only require the database keys of the input iconic objects that can be extracted by using the routines
HGetObj (see section 5.1.1 on page 57) or HAllObj (see section 5.3.1 on page 66). For HGetURL, even this step
can be omitted.

5.2.1 HGetDRL

HGetDRL (see figure 5.9) combines HGetComp (section 5.1.2 on page 59) and HGetRL (section 5.1.3 on page 60). It
reads the runlength encoding of a region (type: Hrlregion, see section 4.2 on page 50) specified by the database
key obj_key of an image object. The region data is copied to region, which must have been allocated before
with a suitable size (for example, by using HAllocRLTmp, see section 3.2.1 on page 41). Therefore, this region
data can be overwritten without side effects. On the other hand, the memory must be deallocated at the end of the
supply procedure (for example, by using HFreeRLTmp). Figure 5.10 shows an example application of HGetDRL.
Note that HGetDRL automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HGetDRL yourself.

5.2.2 HGetFDRL

In contrast to HGetDRL, only a pointer to the region data is returned by HGetFDRL (see figure 5.9). So there is no
need to allocate memory for the data. On the other hand, only read access to the data is allowed. An example
application of HGetFDRL can be seen in figure 5.11.
Note that HGetFDRL automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HGetFDRL yourself.
 5.2.3 HGetURL 63

Names

HGetDRL, HGetFDRL, HGetURL, HGetDImage, HGetObjNum

Synopsis

#include "Halcon.h"

HGetDRL( Hproc_handle proc_handle,

Hkey obj_key,
Hrlregion *region)

HGetFDRL( Hproc_handle proc_handle,

Hkey obj_key,
Hrlregion **region)

HGetURL( Hproc_handle proc_handle,

int par_num,
Hrlregion *region)

HGetDImage(Hproc_handle proc_handle,
Hkey obj_key,
int channel,
Himage *image)

HGetObjNum(Hproc_handle proc_handle,
int par_num,
INT4_8 *num)

Figure 5.9: Additional routines for accessing input image objects.

Hrlregion *region;
Hkey obj_key;
...
HCkP(HAllocRLTmp(proc_handle,&region));
HGetObj(proc_handle,par_num,obj_num,&obj_key);
HGetDRL(proc_handle,obj_key,region);

Parameter Handling
/* processing (in general this should be done calling an action proc.) */
area = 0;
for (i=0; i<region->num; i++)
area += region->rl[i].ce - region->rl[i].cb + 1;
HCkP(HFreeRLTmp(proc_handle,region));

Figure 5.10: Application of HGetDRL.

5.2.3 HGetURL

HGetURL (see figure 5.9) reads all regions passed in the input iconic parameter with the index par_num, com-
putes the union of all these regions, and returns the resulting region in region. The Hrlregion data referenced

Hkey obj_key;
Hrlregion *region;
...
HGetFDRL(proc_handle,obj_key,&region);
/* processing (in general this should be done calling an action proc.) */
area = 0;
for (i=0; i<region->num; i++)
area += region->rl[i].ce - region->rl[i].cb + 1;

Figure 5.11: Application of HGetFDRL.

64 Handling Iconic Objects and Control Parameters

by region must have been allocated before with a suitable size (for example, by using HAllocRLTmp, see sec-
tion 3.2.1 on page 41, which can be increased for example, by using HIncrRL, see section 5.6.5 on page 84).
Therefore, this region data can be overwritten without side effects. On the other hand, the memory must be deal-
located at the end of the supply procedure (for example, by using HFreeRLTmp). Figure 5.12 shows an application
of HGetURL. Note that the area calculated in the example may differ from the sum of the areas of all single regions,
because the single regions may overlap.
Note that HGetURL automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HGetURL yourself.
If you do not want to have the result state checked with HCkP, use HPGetURL instead. HPGetURL and HGetURL
only differ regarding HCkP.

Hrlregion *region;
...
HCkP(HAllocRLTmp(proc_handle,&region));
HGetURL(proc_handle,par_num,region);
/* processing (in general this should be done calling an action proc.) */
area = 0;
for (i=0; i<region->num; i++)
area += region->rl[i].ce - region->rl[i].cb + 1;
HCkP(HFreeRLTmp(proc_handle,region));

Figure 5.12: Application of HGetURL.

5.2.4 HGetDImage

HGetDImage (see figure 5.9 on page 63) combines HGetComp (section 5.1.2 on page 59) and HGetImage (sec-
tion 5.1.4 on page 61). It reads the data of the gray value component channel of the image object specified by the
database key obj_key and returns it in the Himage structure (image).
Note that HGetDImage automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HGetDImage yourself.

Himage image;
Hcpar row,col,gray;
...
HGetSPar(proc_handle,1,LONG_PAR,&row,1); /* row */
HGetSPar(proc_handle,2,LONG_PAR,&col,1); /* column */
coord = HLinCoor(row.par.l,col.par.l,image.width);
HGetDImage(proc_handle,obj_key,IMAGE_INDEX,&image);
/* processing (in general this should be done calling an action proc.) */
switch (image.kind) {
case BYTE_IMAGE:
gray.par.l = image.pixel.b[coord];
gray.type = LONG_PAR;
break;
case FLOAT_IMAGE:
gray.par.d = image.pixel.f[coord];
gray.type = DOUBLE_PAR;
break;
default:
return(H_ERR_WIT); /* wrong image type */
}
HPutCPar(proc_handle,1,&gray,1);

Figure 5.13: Application of HGetDImage: Return the gray value at position (row,col) in the first channel of the input
iconic object obj_key.

For the sake of efficiency, only a pointer to the image matrix is copied to image, instead of copying the data itself.
So, only read access to the image data is recommended in order to avoid unpredictable side effects. Figure 5.13
shows an application of HGetDImage.
 5.2.5 HGetObjNum 65

5.2.5 HGetObjNum

HGetObjNum (see figure 5.9 on page 63) returns the number of iconic objects which are stored in the input iconic
parameter denoted by its index par_num (from 1 to n). It is an alternative to the usage of HReadGVA (compare
page 59). By using HGetObjNum, the example of figure 5.3 on page 59 looks as follows (see figure 5.14).
Note that HGetObjNum automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HGetObjNum yourself.
!
int inp_pars;
INT4_8 num_objs;
Hkey key;
int p,o;
...
/* get number of input iconic parameters: */
/* note: This number is known in general - it is specified by */
/* the operator header in the corresponding DEF file of the */
/* operator */
HReadGV(proc_handle,HGinp_obj,&inp_pars);
for (p=1; p<=inp_pars; p++) {
/* get number of iconic objects per input iconic parameter: */
HGetObjNum(proc_handle,p,&num_objs);
for (o=1; o<=num_objs; o++) {
HGetObj(proc_handle,p,o,&key); /* get key of iconic object */
/* further processing ... */
}
}

Figure 5.14: Application of HGetObjNum: Access the number of iconic objects of an input iconic parameter.

5.3 Loop Macros for Accessing Single Input Objects

This section describes two macros that ease the access of all iconic objects and image components within an input
iconic parameter, see figure 5.15. Please see also the additional loop macros in section 6.1 on page 87 that further

Parameter Handling
facilitate the programming of typical supply procedure.

Names

HAllObj, HAllComp

Synopsis

#include "Halcon.h"

HAllObj( Hproc_handle proc_handle,

int par_num,
Hkey &obj_key,
INT4_8 &index)

HAllComp(Hproc_handle proc_handle,
Hkey obj_key,
Hkey &image_in_key,
Himage &image_in,
INT4_8 &index)

Figure 5.15: Basic loop macros to access iconic objects. “&” denotes output parameters of the macros. This is only
a special notation to make clear that these parameters are changed by the macros. So do not pass
pointers to variables but the variables itself to the macro.
66 Handling Iconic Objects and Control Parameters

5.3.1 HAllObj

HAllObj (see figure 5.15) performs a loop over all iconic objects of a specified input iconic parameter and returns
their database key.

Hkey obj_key;
Hrlregion *region;
Himage image;
INT4_8 index;
...
HAllObj(proc_handle,1,obj_key,index) {
HGetFDRL(proc_handle,obj_key,&region);
HGetDImage(proc_handle,obj_key,IMAGE_INDEX,&image);
}

Figure 5.16: Application of HAllObj: Access the domain (area of definition) and the first gray value channel of all
iconic objects of the first input iconic parameter.

Within the loop, all iconic objects contained in the input iconic parameter with the index2 par_num are accessed
one by one. index is set to the index of the current iconic object to be processed and obj_key is set to the
corresponding database key. Thus, using HAllObj is equivalent to programming an explicit loop over all iconic
objects contained in a parameter and determining the database keys via HGetObj, see also figure 5.3 on page 59.
Figure 5.16 shows an application of HAllObj.

5.3.2 HAllComp

HAllComp performs a loop over all gray value channels (components) of the image object denoted by the database
key obj_key. Within the loop, image_in_key is set to the database key of the current image object and the
corresponding image data is delivered in image_in. Using HAllComp is equivalent to programming an explicit
loop over all channels of an image object using HGetDImage. This also implies that the raw image data, i.e., the
image matrix itself, is not copied. Instead, only a pointer to this data is inserted in image_in. So please restrict
! yourself to reading this data. Any write access to the image matrix will cause unpredictable side effects.

! Note that HAllComp does not check, whether the image object contains at least one channel. Note further, that any
region processing should be performed outside the loop (otherwise you will process the same region again and
again for each channel).

Hkey obj_in;
Hkey obj_out;
Hkey image_in_key;
INT4_8 comp_index;
Himage image_in,image_out;
...
HAllObj(proc_handle,1,obj_in,j) {
HCrObj(proc_handle,1,&obj_out);
HAllComp(proc_handle,obj_in,image_in_key,image_in,comp_index) {
HCkP(HCrImage(proc_handle,image_in_key,1,BYTE_IMAGE,
image_in.width,image_in.height,
&im_out_key,&image_out));
HCkP(IPBRot90(image_in.pixel.b,image_in.width,region_in,
image_out.pixel.b,width,height));
HDefObj(proc_handle,obj_out,im_out_key,comp_index);
}
}

Figure 5.17: Application of HAllComp: Rotate all channels of all image objects of the first input iconic parameter.

Figure 5.17 shows an example of how to use HAllComp. Within the HAllObj loop for each input image object, an
output image object is created and added to the iconic object list of the first output iconic parameter (HCrObj, see
2 So in contrast to the routines described in section 6.1 on page 87, HAllObj allows to specify the desired parameter by its index.
 5.4 Creating Objects and Writing Output Object Parameters 67

section 5.4.1). After that, a loop over all gray value channels of the current image object is performed (HAllComp).
Within this loop, for every gray value channel a new image matrix is created (HCrImage, see section 5.4.7 on
page 70) and filled with the rotated input matrix (IPBRot90). Finally, this matrix is installed as a new gray
value channel of the output image object (HDefObj, see section 5.4.5 on page 69). The corresponding region
transformation (rotating the region and defining the rotated region as new domain, i.e., area of definition, of the
output image object via HDefObj) is omitted in this example.

5.4 Creating Objects and Writing Output Object Parameters

This section describes routines for creating new iconic objects in the HALCON database of iconic objects and for
writing output iconic parameters of a HALCON operator, see figure 5.18. Note that regions, gray value channels,
and XLDs are all stored as individual iconic objects within the database. Thus, for example different image objects
can share the same gray value channels (image matrices) or domains (areas of definition). Therefore, in order to
return iconic objects as the result of a HALCON operator you have to

• store the computed regions, channels, and XLDs in the HALCON database of iconic objects,
• combine regions and channels to image objects,
• and add the appropriate iconic objects to the corresponding output iconic parameters.

Names

HCrObj, HCopyObj, HPutDRL, HPutImage

Synopsis

#include "Halcon.h"

HCrObj( Hproc_handle proc_handle,

int par_num,
Hkey *obj_key)

HCopyObj( Hproc_handle proc_handle,

Hkey obj_key,

Parameter Handling
int par_num,
Hkey *obj_key)

HPutDRL( Hproc_handle proc_handle,

Hkey obj_key,
Hrlregion *region,
Hkey *rl_key)

HPutImage( Hproc_handle proc_handle,

Himage *image,
bool copy,
Hkey *obj_key)

Figure 5.18: Basic routines for creating new iconic objects and writing output iconic parameters (to be continued).

5.4.1 HCrObj

HCrObj (see figure 5.18) creates a new image object in the HALCON database of iconic objects and adds it to
the list of iconic objects in the output iconic parameter with the index par_num. Note that more than one image
object can be returned in the same output parameter by iterating calls of HCrObj using the same par_num: Each
call appends the database key of the new iconic object at the end of the iconic object list for the parameter.
The new image object contains the following default image components:
68 Handling Iconic Objects and Control Parameters

Names

HDefObj, HPutDImage, HCrImage, HCrXLD

Synopsis

#include "Halcon.h"

HDefObj( Hproc_handle proc_handle,

Hkey obj_key,
Hkey comp_key,
int comp)

HPutDImage( Hproc_handle proc_handle,

Hkey obj_key,
int comp,
Himage *image,
bool copy,
Hkey *image_key)

Herror HCrImage( Hproc_handle proc_handle,

Hkey image_key_in,
int index,
int type,
HIMGDIM width,height,
Hkey *image_key_out,
Himage *image_out)

HCrXLD( Hproc_handle proc_handle,

int par_num,
XLD *xld,
int xld_type,
Hkey *used_xlds,
int num_used_xlds,
DBFreeProc free_proc,
Hkey *obj_key)

Figure 5.19: Basic routines for creating new iconic objects and writing output iconic parameters (continued).

• The region component specifying the area of definition, i.e., the domain of the image, is set to the empty
region. This component can be changed using HPutDRL (see section 5.4.3 on page 69) or HPutRect (see
section 6.2.2 on page 94).
• All channels are marked as undefined, i.e., the new image object contains no gray value components. Chan-
nels can be added to the iconic object using HPutImage (see section 5.4.4) and HDefObj (see section 5.4.5)
or HPutDImage (see section 5.4.6 on page 70).

Figure 5.17 on page 66 and figure 5.21 on page 70 show examples how to use HCrObj.
Note that HCrObj automatically checks the result state of the underlying procedure with the macro HCkP, (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HCrObj yourself.

5.4.2 HCopyObj

HCopyObj (see figure 5.18 on page 67) creates a new iconic object (image, region, or XLD) that contains the same
components as an already existing iconic object specified by its database key obj_key. The new iconic object is
stored in the HALCON database of iconic objects and appended to the list of iconic objects in the output iconic
parameter with the index par_num. The database key of the new image object is returned in obj_key.
Note that HCopyObj automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HCopyObj yourself.
 5.4.3 HPutDRL 69

Hkey obj_key_in,obj_key_out,reg_key_out;
Hrlregion *region_in;
Hrlregion *region_out;
INT4_8 num_objs;
...
par_in = 1; /* index of input parameter */
par_out = 1; /* index of output parameter */
HReadGVA(proc_handle,HGnum_obj,&num_objs,par_in);
for (o=1; o<=num_objs; o++) {
HGetObj(proc_handle,par_in,o,&obj_key_in);
HGetFDRL(proc_handle,obj_key_in,&region_in);
/* compute some region transformation ... */
transform(region_in,region_out);
HCopyObj(proc_handle,obj_key_in,par_out,&obj_key_out);
HPutDRL(proc_handle,obj_key_out,region_out,&reg_key_out);
}

Figure 5.20: Create an image object with HCopyObj and insert a region component.

Similar to HCrObj, the components of a new image object can be reassigned using HDefObj etc. HCopyObj is
especially useful, when output iconic objects hardly differ from the corresponding input objects.

5.4.3 HPutDRL

HPutDRL (see figure 5.18 on page 67) stores region data encoded in the Hrlregion structure region in the
HALCON database of iconic objects and returns the database key of the new iconic object. Note that HPutDRL
actually copies the data itself, not only a pointer to the data. In addition to that, the region object is assigned to the
image object specified by the database key obj_key as the region component. The latter might have been created
before by using HCrObj or HCopyObj, see figures 5.20 and 5.21.
Note that HPutDRL automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HPutDRL yourself.
!

Parameter Handling
5.4.4 HPutImage

HPutImage (see figure 5.19 on page 68) stores the gray value channel (image matrix) image in the database of
iconic objects and returns the corresponding database key in the parameter obj_key. This key can be used to insert
the gray value channel (now encapsulated in a database object) as a component of an arbitrary number of image
objects (see HDefObj in section 5.4.5). The parameter copy (false or true) specifies, whether the pixel data is
copied to the HALCON database3 or only the address of the data is passed to the database object. Figure 5.21
shows a typical example for how to use HPutImage.
Note that HPutImage automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HPutImage yourself.
!
5.4.5 HDefObj

HDefObj (see figure 5.19 on page 68) reassigns the component comp (0 . . . n) of an image object given by its
database key comp_key. A typical application of this routine is shown in figure 5.21: Image data is stored in a
database object using HPutImage. Furthermore, a new image object is created by HCrObj. This new object does
not contain any gray value channels, see section 5.4.1 on page 67. Using HDefObj, the previously stored image
data is assigned as default gray value component 1 (IMAGE_INDEX) of the new image object.
Note that HDefObj automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HDefObj yourself.
3 This is necessary if the original data is stored in temporary memory or if the data will be modified later on.
!
70 Handling Iconic Objects and Control Parameters

Himage image;
Hrlregion *region;
Hkey image_key,obj_key;
...
/* processed image data: image */
/* processed region data: region */
par_num = 1;
HPutImage(proc_handle,&image,true,&image_key);
HCrObj(proc_handle,par_num,&obj_key);
HDefObj(proc_handle,obj_key,image_key,IMAGE_INDEX);
HPutDRL(proc_handle,obj_key,region,&region_key);

Figure 5.21: Creating a new image object using basic Extension Package Interface routines.

5.4.6 HPutDImage

HPutDImage (see figure 5.19 on page 68) combines HPutImage and HDefObj. It stores the gray value channel
(image matrix) image in the HALCON database of iconic objects and returns the corresponding database key in
image_key. The parameter copy (false or true) is used as in HPutImage and specifies, whether the pixel data
is copied4 or only a pointer to the data is passed to the database. Moreover, the gray value channel is inserted into
the image object obj_key as component comp (1 . . . n). Figure 5.22 shows a typical application of this routine.
Note that HPutDImage automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HPutDImage yourself.

Hkey obj_key,k;
Himage image;
Hrlregion *region;
...
/* image: processed gray value data */
/* region: region data */
HCrObj(proc_handle,par_num,&obj_key);
HPutDImage(proc_handle,obj_key,IMAGE_INDEX,&image,false,&k);
HPutDRL(proc_handle,obj_key,region,&k);

Figure 5.22: Creating a new image object using HPutDImage and HPutDRL.

5.4.7 HCrImage

HCrImage (see figure 5.19 on page 68) is used for creating output images especially in the context of filter5
operations. As you know, HALCON image objects can share the underlying image matrices (gray value channels).
Thus, input image objects of a filter operation might only differ in their domain (i.e., in their region component),
but not in their gray values. Such objects have different database keys and different regions, but contain references
to the same gray value channels. Obviously, it is very desirable to propagate this relation to the resulting output
image objects as well.
HCrImage allocates memory for the image matrix within the Himage structure image_out (similar to HNewImage
in section 3.2.2 on page 43). The parameters type (BYTE_IMAGE, LONG_IMAGE, FLOAT_IMAGE, etc.; see figure 4.2
on page 50, width and height allow to specify the pixel type and the size of the new matrix. Note that new
matrices are by default initialized with 0. However, this can be suppressed from outside or inside of the operator,
see the discussion of HNewImage in section 3.2.2 on page 43 for details.
Furthermore, HCrImage creates a new database object encapsulating this image data and returns the corresponding
database key in image_key_out (similar to HPutImage in section 5.4.4 on page 69).
Finally, HCrImage establishes a link between the original input image data (referenced by the database key
image_key_in) and this new iconic object to avoid the allocation of multiple output matrices per input ma-
trix. HCrImage checks, whether there already exists an output matrix with the specified index index (see below)
4 This is necessary, if the pixel data was stored in temporary memory or if it will be modified later on.
5 This is due to the fact, that filtering only modifies the gray values but not the regions of image objects.
 5.4.8 HCrXLD 71

Hkey obj_key,image_key_in,image_key_out,key_out;
Hrlregion *region;
Himage image_in,image_out;

...
HGetSPar(proc_handle,1,LONG_PAR,&Rows,1); /* height: filter mask */
HGetSPar(proc_handle,2,LONG_PAR,&Cols,1); /* width: filter mask */

HAllObj(proc_handle,1,obj_key,i) { /* all input images */

HGetFDRL(proc_handle,obj_key,&region); /* get region data */
HGetComp(proc_handle,obj_key,IMAGE1,&image_key_in);
if (image_key_in == UNDEFINED)
return(H_ERR_UNDI); /* 'undefined image' */
HGetImage(proc_handle,image_key_in,&image_in); /*get image data*/
HCkP(HCrImage(proc_handle,image_key_in,1,image_in.kind,
image_in.width,image_in.height,
&image_key_out,&image_out));

HCkP(IPFilterOperation(&image_in,region,Rows,Cols,&image_out));

HCopyObj(proc_handle,obj_key,1,&key_out); /* create result obj.*/

HDefObj(proc_handle,key_out,image_key_out,IMAGE1);
/* insert the result image in output object */
}

Figure 5.23: A typical example for using HCrImage: Providing an empty image matrix for a filter operation.

for a given input image image_key_in. If there is any, only a reference to it is returned in image_out and
image_key_out instead of creating a new matrix. Without this mechanism, a new matrix would be created again
and again within the loop over all input iconic objects (HAllObj).
The parameter index is only of importance, if more than one output matrix per input matrix is needed: This is
necessary for example, if an edge filter is performed in x- and y-direction independently. In this case, HCrImage
must be called several times for every input component – one time for each output matrix to be created. Assign
increasing indices (1, 2, 3, . . . ) to the parameter index to indicate a new output matrix. If there is only one matrix
to create for the output image, set index to 1.

Parameter Handling
Figure 5.23 shows an exemplary application of HCrImage.
Note that HCrImage is no macro, i.e., it does not check the result state of the underlying procedure using HCkP (see
section 5.6.1 on page 83). Thus, you must call HCkP on HCrImage yourself as shown in the example.
!
5.4.8 HCrXLD

HCrXLD (see figure 5.19 on page 68) is used for creating XLD objects in the HALCON database of iconic objects.
The parameter xld_type allows to specify the kind of XLD to be created: It has to be set to XLD_CONTOUR_ID
in case of a contour and to XLD_POLYGON_ID in case of a polygon. Corresponding to the selected type, HCrXLD
expects a pointer to Hcont or a pointer to Hpoly in the parameter xld. In both cases, not the underlying XLD data
but only the pointers to the data are copied to the database. Thus, you must not deallocate or overwrite the XLD
structures after calling HCrXLD. !
Note that HCrXLD automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HCrXLD yourself.
HCrXLD expects an appropriate deallocation routine for the XLD data in the parameter free_proc. For XLD
!
contours, please use

(DBFreeProc) HXLDFreeContour

For XLD polygons allocated based on HAlloc use

72 Handling Iconic Objects and Control Parameters

Hcpar rows[99], cols[99];

INT4_8 i,num_points;
Hkey key_out;
Hcont *cont;

...
HGetCPar(proc_handle,1,DOUBLE_PAR,rows,1,99,&num_points);
HGetCPar(proc_handle,2,DOUBLE_PAR,cols,1,99,&num_points);

/* create a contour (in general, this should be done */

/* calling an appropriate action procedure) */
HCkP(HAllocXLDCont(proc_handle,&cont,num_points));
for (i=0; i < num_points; i++ {
cont->row[i] = rows[i].par.d;
cont->col[i] = cols[i].par.d;
}
cont->num = num_points;
HCrXLD(proc_id,1,cont,XLD_CONTOUR_ID,NULL,0,
(DBFreeProc)HXLDFreeContour,&key_out);

Figure 5.24: A typical example for using HCrXLD: Create an XLD contour from a list of points.

(DBFreeProc) HXLDFreePolygon

Finally, HCrXLD not only creates a new database object, but also appends this object to the output iconic parameter
with index par_num. Figures 5.24 shows a typical application of HCrXLD.

5.5 Reading and Writing Control Parameters

This section describes routines for reading and writing in-/output control parameters, see figure 5.25, figure 5.29,
figure 5.30, and figure 5.35. Interchanging control data with the host language is done via arrays of the data type
INT4_8 for LONG_PAR, double for DOUBLE_PAR, Hphandle for HANDLE_PAR, char* for STRING_PAR, or Hcpar
for MIXED_PAR array types (see section 4.4 on page 55).
Control parameters can be passed through the HALCON interface in two different ways: by reference or by
value. The former is more efficient but does not allow to modify the values. It is supported by the routines
HGetPElemL, HGetPElemD, HGetPElemS, and HGetPPar for reading, depending on the expected type of the input
array. HGetPElem provides a general, type independent read access. In case of writing output control param-
eters, HPutPPar and HPutPElem are provided. In contrast, the routines HGetElemL, HGetElemD, HGetElemS,
HGetCElemH1, HGetCElemH, HGetCElemHN, and HGetCPar return a copy of the input array, whereas HPutElem,
HPutElemH, and HPutCPar copy an array to an output control parameter.

5.5.1 HGetPElemL, HGetPElemD, HGetPElemS

HGetPElemL, HGetPElemD, and HGetPElemS (see figure 5.25) return a reference in elem to the value array of the
input control parameter at the position par (1 . . . n). According to the expected type of the array, HGetPElemL
is used to get LONG_PAR arrays, HGetPElemD for DOUBLE_PAR, and HGetPElemS for STRING_PAR arrays. The
behavior of the routines in case of passing array types different to the expected can be specified by the convert
parameter. Following values are supported:

CONV_NONE supports no conversion and accepts only the requested element type. Otherwise, the error ’wrong
type of input parameter x’ (H_ERR_WIPTx) will be returned.
CONV_CAST provides conversion of LONG_PAR and DOUBLE_PAR values to the requested type by a cast. In case of
conversion, the array is copied to an ad hoc allocated memory buffer. This buffer is freed automatically when
the operator returns. LONG_PAR and DOUBLE_PAR value types can not be casted to type STRING_PAR and
vice versa. In this case, error ’wrong type of input parameter x’ (H_ERR_WIPTx) will be returned.
 5.5.1 HGetPElemX 73

Names

HGetPElemL, HGetPElemD, HGetPElemS, HGetPPar, HGetPElem

Conversion Flags

CONV_NONE /* no conversion; do only consider original element types */

CONV_CAST /* <INT4_8>=(INT4_8)<double>; <double>=(double)<INT4_8> */
CONV_IDNT /* convert double to INT4_8, if double has no fraction */
CONV_RND /* <INT4_8>=(INT4_8)(<double>+0.5) */

Synopsis

#include "Halcon.h"

HGetPElemL( Hproc_handle proc_handle,

int par,
int convert,
INT4_8 const*restrict *elem,
INT4_8 *num)

HGetPElemD( Hproc_handle proc_handle,

int par,
int convert,
double const*restrict *elem,
INT4_8 *num)

HGetPElemS( Hproc_handle proc_handle,

int par,
int convert,
char const* const*restrict *elem,
INT4_8 *num)

HGetPPar( Hproc_handle proc_handle,

int par,
Hcpar const* restrict *val,
INT4_8 *num)

HGetPElem( Hproc_handle proc_handle,

Parameter Handling
int par,
void const*restrict *elem,
INT4_8 *num,
int *type)

Figure 5.25: Routines for reading control input parameters by reference.

CONV_IDNT converts DOUBLE_PAR values of a DOUBLE_PAR or MIXED_PAR array to type LONG_PAR when passed
to HGetPElemL. This conversion is performed only if all double values of the input array have no frac-
tion, i.e., the cast is reversible. When passed to HGetPElemD, values of type LONG_PAR are casted to type
DOUBLE_PAR. Any other conversion is not supported and in this case the error ’wrong type of input
parameter x’ (H_ERR_WIPTx) is returned. In case of conversion, the array is copied to an ad hoc allocated
memory buffer. This buffer is freed automatically when the operator returns.
CONV_RND provides conversion by rounding when DOUBLE_PAR values have to be converted to LONG_PAR type
(HGetPElemD). LONG_PAR values are casted to DOUBLE_PAR if passed to HGetPElemD. Otherwise, the er-
ror ’wrong type of input parameter x’ (H_ERR_WIPTx) will be returned. In case of conversion, the
array is copied to an ad hoc allocated memory buffer. This buffer is freed automatically when the operator
returns.

Any conversion of input array types will be paid for by performance and memory consumption. Refer to
HGetPElem (see section 5.5.3) if efficient support of different array types is important. The current number of
parameter values is returned in num.
74 Handling Iconic Objects and Control Parameters

Note that HGetPElemL, HGetPElemD, and HGetPElemS automatically check the result state of the underlying pro-
! cedure similarly to the macro HCkP (see section 5.6.1 on page 83). Thus, you must not use HCkP on HGetPElemL,
HGetPElemD, or HGetPElemS yourself.
Figure 5.26 shows the usage of HGetPElemL andHGetPElemS together with HGetPPar (compare section 5.5.2).

5.5.2 HGetPPar

HGetPPar (see figure 5.25 on page 73) returns the reference to a MIXED_PAR array of Hcpar structures, which
contain the parameter values of the input control parameter at the position par (1 . . . n). Contrary to HGetCPar
(see section 5.5.7 on page 76), HGetPPar is much more efficient in terms of memory overhead, because it just
returns pointers to the values instead of copying them. On the other hand, the parameter values may only be read
and must not be modified. Note that for every parameter value, its type (LONG_PAR, DOUBLE_PAR, STRING_PAR)
is also stored within the Hcpar structure. Therefore, the same control parameter may contain values of different
control data types. In case the input array is of different type to MIXED_PAR, the array is copied and converted to an
ad hoc allocated memory buffer of Hcpar structures. This buffer is freed automatically when the operator returns.
The current number of parameter values is returned in num.
Note that HGetPPar automatically checks the result state of the underlying procedure similarly to the macro HCkP
! (see section 5.6.1 on page 83). Thus, you must not use HCkP on HGetPPar yourself.
Figure 5.26 shows the usage of HGetPPar together with HGetPElemL and HGetPElemS (compare section 5.5.1 on
page 72).

INT4_8 const *ctrl1; /* LONG_PAR array */

char const*const *ctrl2; /* STRING_PAR array */
Hcpar const *ctrl3; /* MIXED_PAR array of Hcpar structures */
INT4_8 num; /* length of an input array */

/* Read all values of parameter number 1. Say, we expect a */

/* LONG_PAR array but also tolerate double values. */
HGetPElemL(proc_handle,1,CONV_CAST,&ctrl1,&num);
/* now ctrl1[0] == 5; ctrl1[1] == 6; */
/* Read a string in parameter number 2. Say, we expect a */
/* STRING_PAR array. */
HGetPElemS(proc_handle,2,CONV_NONE,&ctrl2,&num);
/* now ctrl2[0] == "Text" */
/* Read a tuple of float values in parameter number 3. */
/* At this parameter we handle any value type */
HGetPPar(proc_handle,3,&ctrl_val3,&num);
/* now ctrl3[0].type == DOUBLE_PAR, ctrl3[0].par.d == 1.7 */
/* ctrl3[1].type == LONG_PAR, ctrl3[1].par.l == 4 */
/* ctrl3[2].type == STRING_PAR, ctrl3[2].par.s == "ctrl" */
...

Figure 5.26: Read the control parameter values of the operator call demo([5,6.8],’Text’,[1.7,4,’ctrl’]) using
HGetPElemL, HGetPElemS, and HGetPPar.

5.5.3 HGetPElem

A general access on input control parameter without any implicite conversion is provided by the routine HGetPElem
(see figure 5.25). HGetPElem returns in elem a reference to the input array of arbitrary type of the input control
parameter with the index par (1 . . . n). The length of the array is returned in num. type holds the array type of the
returned array and can take the values LONG_PAR, DOUBLE_PAR, STRING_PAR, and MIXED_PAR, coding arrays of
type INT4_8, double, char*, and Hcpar, respectively.
Figure 5.27 shows the usage of HGetPElem.
 5.5.4 HGetCElemX 75

const void *restrict ctrl1;

INT4_8 n1;
int t1;

/* Read all values of parameter number 1 */

HGetPElem(proc_handle, 1, &e1, &n1, &t1);
switch( t1)
{
case LONG_PAR:
{
INT4_8 const *l = (INT4_8 const *)e1;
...
break;
}
case DOUBLE_PAR:
{
double const *d = (double const *)e1;
...
break;
}
case STRING_PAR:
{
char const *const *s = (char const *const *)e1;
...
break;
}
case MIXED_PAR:
{
Hcpar const *cpar = (Hcpar const *)e1;
...
break;
}
default:
return H_ERR_WIPT1;
}

...

Parameter Handling
Figure 5.27: Read the control parameter values of the first control parameter of an operator using HGetPElem.

5.5.4 HGetCElemH1, HGetCElemH, HGetCElemHN

HGetCElemH1 retrieves a single handle from an input parameter. HGetCElemH retrieves all handles from an input
parameter. HGetCElemHN retrieves a given number N of handles from an input parameter. The returned array
contains pointers to the data stored in the handles. It is freed automatically when the operator finishes.

5.5.5 HGetElemL, HGetElemD, HGetElemS

HGetElemL, HGetElemD, and HGetElemS (see figure 5.29) return a copy of the input control parameter array with
the index par (1 . . . n). According to the expected type of the array, HGetElemL is used to get LONG_PAR arrays,
HGetElemD for DOUBLE_PAR, and HGetElemS for STRING_PAR arrays. In contrast to HGetPElemL, HGetPElemD,
and HGetPElemS, the input arrays will be allocated and the values copied in any case. Therefore, the resulting array
can be modified with the drawback of memory overhead and loss of performance. The kind of memory allocation
(compare section 3.2 on page 41) can be specified by the parameter memtype. It supports the values HMEMglobal,
HMEMlocal, and HMEMtemp, specifying the allocation function HAlloc, HAllocLocal, or HAllocTmp that is used
internally. The specified function is used by the routines to allocate the array, respectively. But note that this array
must be freed explicitly with the according function HFree, HFreeLocal or HFreeTmp after usage. The behavior
of the routines in case of passing array types different to the expected can be specified by the convert parameter
according to the description in section 5.5.1 on page 72.
76 Handling Iconic Objects and Control Parameters

Names

HGetCElemH1, HGetCElemH, HGetCElemHN

Synopsis

#include "Halcon.h"

HGetCElemH1( Hproc_handle proc_handle,

int par,
H_HANDLE_TYPE const *htype,
Hphandle elem)

HGetCElemH( Hproc_handle proc_handle,

int par,
H_HANDLE_TYPE const *htype,
Hphandle elem,
INT4_8 *num)

HGetCElemHN( Hproc_handle proc_handle,

int par,
H_HANDLE_TYPE const *htype,
INT4_8 num,
Hphandle elem)

Figure 5.28: Routines for reading handles by copy.

Note that HGetPPar automatically checks the result state of the underlying procedure similarly to the macro HCkP
! (see section 5.6.1 on page 83). Thus, you must not use HCkP on HGetPPar yourself.

5.5.6 HCopyElemL, HCopyElemD

HCopyElemL and HCopyElemD (see figure 5.30) read the parameter values of the input control parameter with the
index par (1 . . . n) and write them to the array elem that must have been allocated before with a suitable size (see
HGetCParNum for information on getting the actual array length). According to the routine’s suffix, HCopyElemL
expects LONG_PAR, HCopyElemD DOUBLE_PAR arrays. The behavior of the routines in case of passing array types
different to the expected can be specified by the convert parameter according to the description in section 5.5.1
on page 72. The number of elements that have been allocated for elem must be passed to num. In return, num will
hold the number of actually copied array indices.
Note that HCopyElemL and HCopyElemD automatically check the result state of the underlying procedure similarly
! to the macro HCkP (see section 5.6.1 on page 83). Thus, you must not use HCkP on HCopyElemL and HCopyElemD
yourself.

5.5.7 HGetCPar

HGetCPar (see figure 5.30) reads the parameter values of the input control parameter with the index par (1 . . . n)
and writes them to the array val of Hcpar structures that must have been allocated before with a suitable size.
Note that HGetCPar automatically checks the result state of the underlying procedure similarly to the macro HCkP
! (see section 5.6.1 on page 83). Thus, you must not use HCkP on HGetCPar yourself.
For every input value, its type (LONG_PAR, DOUBLE_PAR, STRING_PAR) is also stored within the Hcpar structure.
Thus, it is possible to pass different control data types within one control parameter of a HALCON operator. The
current number of values is returned in num. HGetCPar allows to restrict the parameter access in two respects:
• The expected type can be specified by type. This also includes type combinations such as
LONG_PAR | DOUBLE_PAR.
• The expected number of values can be specified by the interval (min,max), whereas max should not exceed
the number of allocated Hcpar elements within the array val.
 5.5.8 HGetSPar 77

Names

HGetElemL, HGetElemD, HGetElemS

Conversion Flags

CONV_NONE /* no conversion; do only consider original element types */

CONV_CAST /* <INT4_8>=(INT4_8)<double>; <double>=(double)<INT4_8> */
CONV_IDNT /* convert double to INT4_8, if double has no fraction */
CONV_RND /* <INT4_8>=(INT4_8)(<double>+0.5) */

Synopsis

#include "Halcon.h"

HGetElemL( Hproc_handle proc_handle,

int par,
int convert,
int memtype,
INT4_8 *restrict *elem,
INT4_8 *num)

HGetElemD( Hproc_handle proc_handle,

int par,
int convert,
int memtype,
double *restrict *elem,
INT4_8 *num)

HGetElemS( Hproc_handle proc_handle,

int par,
int convert,
int memtype,
char *restrict*restrict *elem,
INT4_8 *num)

Figure 5.29: Routines for reading control input parameters by copy.

Parameter Handling
If the specified number or types of values are violated, HGetCPar exits the supply procedure with an appropriate
error message. Figure 5.32 shows an application of HGetCPar.
Note that in case of string parameters, memory has to be allocated for val[i].par.s. The easiest way to do this
is to use HAllocStringMem specifying the expected number of characters for all input strings, see section 5.5.10.

5.5.8 HGetSPar

HGetSPar is a simplified version of HGetCPar. In contrast to the latter, a fixed number of parameter values is read,
see figure 5.33. Therefore, the routine does not return the actual number6 of values.
Note that HGetSPar automatically checks the result state of the underlying procedure similarly to the macro HCkP
(see section 5.6.1 on page 83). Thus, you must not use HCkP on HGetSPar yourself.
!
5.5.9 HGetCParNum

HGetCParNum returns the length of input control arrays of the input control parameter with the index par (1 . . . n).
This makes it possible to allocate exactly as much memory for parameter values as needed for reading them,
for example, via HCopyElemL, HCopyElemD, or HGetCPar. As an alternative, you can use the reference passing
routines as HGetPElem or HGetPPar, or routines as HGetElemL that allocate memory implicitly. Figure 5.34
shows an application of HGetCParNum.
6 This number is fixed. If more or less values are passed to the HALCON operator, HGetSPar exits the supply procedure with an error.
78 Handling Iconic Objects and Control Parameters

Names

HCopyElemL, HCopyElemD, HGetCPar

Conversion Flags

CONV_NONE /* no conversion; do only consider original element types */

CONV_CAST /* <INT4_8>=(INT4_8)<double>; <double>=(double)<INT4_8> */
CONV_IDNT /* convert double to INT4_8, if double has no fraction */
CONV_RND /* <INT4_8>=(INT4_8)(<double>+0.5) */

Synopsis

#include "Halcon.h"

HCopyElemL( Hproc_handle proc_handle,

int par,
int convert,
INT4_8 *restrict elem,
INT4_8 *num);

HCopyElemD( Hproc_handle proc_handle,

int par,
int convert,
double *restrict elem,
INT4_8 *num);

HGetCPar( Hproc_handle proc_handle,

int par,
int type,
Hcpar *val,
INT4_8 min,
INT4_8 max,
INT4_8 *num)

Figure 5.30: Routines for reading control input parameters by copy to a preallocated array.

INT4_8 l[10]; /* maximum array length of 10 */

INT4_8 num = 10;

/* read a short/int/long value in parameter 1 */

HCopyElemL(proc_handle,1,CONV_RND,l,&num);
/* now l == [2,4], num = 2 */
...

Figure 5.31: Read the parameter values [1.7,4] of control parameter 1 using HCopyElemL.

Note that HGetCParNum automatically checks the result state of the underlying procedure similarly to the macro
! HCkP (see section 5.6.1 on page 83). Thus, you must not use HCkP on HGetCParNum yourself.

5.5.10 HAllocStringMem

In case of string parameters, additional memory for the parameter values has to be allocated, because the Hcpar
structure only contains a pointer to char. The easiest way to do this is to use HAllocStringMem specifying
the expected number of characters for all input strings (parameter size) at the begin of a supply procedure, see
figure 5.32 and figure 5.33. It is not necessary to free this memory explicitly — this is done automatically at the
end of the supply procedure.
Note that HAllocStringMem automatically checks the result state of the underlying procedure using HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HAllocStringMem yourself.
 5.5.11 HPutPElem 79

Hcpar par1,par2;
Hcpar par3[10];

/* allocate memory for strings */

HAllocStringMem(proc_handle,1000);
/* read a short/int/long value in parameter 1 */
HGetCPar(proc_handle,1,LONG_PAR,&par1,1,1,&num);
/* now par1.par.l == 5 */
/* read a string in parameter 2 */
HGetCPar(proc_handle,2,STRING_PAR,&par2,1,1,&num);
/* now par2.par.s == "Text" */
/* read a tuple of float values in parameter 3 */
/* (max. 10 values) */
HGetCPar(proc_handle,3,DOUBLE_PAR,par3,1,10,&num);
for (i=0; i<num; i++) {
/* par3[i].par.d == 0.5,1.7,4.4 */
...

Figure 5.32: Read the control parameter values of the operator call demo(5,’Text’,[0.5,1.7,4.4]) using
HGetCPar.

Hcpar par1,par2;
Hcpar par3[3];

/* allocate memory for strings */

HAllocStringMem(proc_handle,1000);
/* read a short/int/long value in parameter 1 */
HGetSPar(proc_handle,1,LONG_PAR,&par1,1);
/* now par1.par.l == 5 */
/* read a string in parameter 2 */
HGetSPar(proc_handle,2,STRING_PAR,&par2,1);
/* now par2.par.s == "Text" */
/* read a tuple of 3 float values in parameter 3 */
HGetSPar(proc_handle,3,DOUBLE_PAR,par3,3);
for (i=0; i<num; i++) {
/* par3[i].par.d == 0.5,1.7,4.4 */
...

Parameter Handling
Figure 5.33: Read the control parameter values of the operator call demo(5,’Text’,[0.5,1.7,4.4]) using
HGetSPar.

5.5.11 HPutPElem

HPutPElem (see figure 5.35 on page 81) writes a native array to the output control parameter with the index par.
val holds the reference to the array of the according type, coded in type (LONG_PAR for arrays of type INT4_8,
DOUBLE_PAR, for double, and STRING_PAR for char* arrays). The length of the array is passed in num. Instead
of copying the array like HPutElem does, HPutPElem directly stores the pointer to the output control parameter
and, thus, causes less overhead. Therefore, this array has to be allocated “permanently”, i.e. it must be allocated
by using HAlloc (see section 3.2.2 on page 43). Furthermore, the array must not be freed after passing it to
HPutPElem. Figure 5.36 shows how to write output control data with HPutPElem.
Note that HPutPElem automatically checks the result state of the underlying procedure similarly to the macro HCkP
(see section 5.6.1 on page 83). Thus, you must not use HCkP on HPutPElem yourself.
!
5.5.12 HPutPPar

HPutPPar (see figure 5.35 on page 81) is an alternative to HPutCPar and writes control data to the output control
parameter with the index par. However, instead of copying the num values like HPutCPar does, HPutPPar directly
stores the pointer to the array of Hcpar structures (val). Thus, it causes less overhead. As HPutPPar directly uses
the passed Hcpar array without copying, this array has to be allocated “permanently”, i.e. it must be allocated by
80 Handling Iconic Objects and Control Parameters

Hcpar par1,par2;
Hcpar *par3;
INT4_8 num;

/* allocate memory for strings */

HAllocStringMem(proc_handle,1000);
/* read a short/int/long value in parameter 1 */
HGetSPar(proc_handle,1,LONG_PAR,&par1,1);
/* now par1.par.l == 5 */
/* read a string in parameter 2 */
HGetSPar(proc_handle,2,STRING_PAR,&par2,1);
/* now par2.par.s == "Text" */
/* read a tuple of float values in parameter 3; */
/* first, get the number of values */
HGetCParNum(proc_handle,3,&num);
/* now num == 3 */
/* second, allocate memory for the values and read them */
HCkP(HAllocTmp(proc_handle,(void**)&par3,(size_t)(num*sizeof(Hcpar))));

HGetSPar(proc_handle,3,DOUBLE_PAR,par3,num);
for (i=0; i<num; i++) {
/* par3[i].par.d == 0.5,1.7,4.4 */
...

Figure 5.34: Use HGetCParNum to get the number of control values before reading the control parameter values of
the operator call demo(5,’Text’,[0.5,1.7,4.4]).

using HAlloc (see section 3.2.2 on page 43). Furthermore, the array must not be freed after passing it to HPutPPar.
Figure 5.37 shows how to write output control data with HPutPPar.
Note that HPutPPar automatically checks the result state of the underlying procedure similarly to the macro HCkP
! (see section 5.6.1 on page 83). Thus, you must not use HCkP on HPutPPar yourself.
As already mentioned, every data element may use a different type, because the types of the parameter values
(LONG_PAR, DOUBLE_PAR, STRING_PAR) are stored with each Hcpar structure.

5.5.13 HPutElem

HPutElem (see figure 5.35) writes a native array to the output control parameter with the index par of a HALCON
operator. The type of the array passed in val is coded by type, with LONG_PAR for arrays of type INT4_8,
DOUBLE_PAR, for double, STRING_PAR for char* arrays. In contrast to HPutPElem, the values are copied by this
routine.

5.5.14 HPutElemH

HPutElemH (see figure 5.35) writes num handle references to the output control parameter with the index par of
a HALCON operator. elem points to an array that holds num elements. HHandleInfo contains information about
the type of the corresponding handles. Most notably,HHandleInfo contains pointers to the functions that operate
on the handles (clear, serialize, deserialize and signal).
! Note that the output control variable gains ownership of all pointers that are in elem. When aborting an
operator with an error, those values must not be cleared inside the operator’s code, but will be cleared automatically
when cleaning the output control variable.

5.5.15 HPutCPar

HPutCPar (see figure 5.35) writes control data to the output control parameter with the index par of a HALCON
operator. The num values in the Hcpar structure val are copied by this routine. Because the types of the parameter
 5.5.15 HPutCPar 81

Names

HPutPElem, HPutPPar
HPutElemH, HPutCPar

Synopsis

#include "Halcon.h"

/* --- writing output parameters by reference */

HPutPElem( Hproc_handle proc_handle,
int par,
void *val,
INT4_8 num,
int type)

HPutPPar( Hproc_handle proc_handle,

int par,
Hcpar *val,
INT4_8 num)

/* --- writing output parameters by copy */

HPutElem( Hproc_handle proc_handle,
int parnr,
void const *val,
INT4_8 num,
int type)

HPutElemH( Hproc_handle proc_handle,

int par,
void const *elem,
INT4_8 num,
H_HANDLE_TYPE *HHandleInfo)

HPutCPar( Hproc_handle proc_handle,

int par,
Hcpar const *val,
INT4_8 num)

Parameter Handling
Figure 5.35: Routines for writing control output parameters.

double *d;

HCkP(HAlloc(proc_handle,sizeof(*d)*2,&d));

d[0] = 1.2;
d[1] = 4.4;
HPutPElem(proc_handle,1,d,2,DOUBLE_PAR);

Figure 5.36: Write the control parameter values [1.2,4.4] using HPutPElem.

values (LONG_PAR, DOUBLE_PAR, STRING_PAR) are stored with each Hcpar structure, you can use a different type
for every data element, see figure 5.38.
Note that HPutCPar automatically checks the result state of the underlying procedure similarly to the macro HCkP
(see section 5.6.1 on page 83). Thus, you must not use HCkP on HPutCPar yourself.
!
82 Handling Iconic Objects and Control Parameters

Hcpar *par;

HCkP(HAlloc(proc_handle,(size_t)(sizeof(Hcpar)*2),(void**)&par));

par[0].par.l = 6;
par[0].type = LONG_PAR;
par[1].par.d = 4.4;
par[1].type = DOUBLE_PAR;
HPutPPar(proc_handle,1,par,2);

Figure 5.37: Write the control parameter values [6,4.4] using HPutPPar.

Hcpar par[2];

par[0].par.l = 6;
par[0].type = LONG_PAR;
par[1].par.d = 4.4;
par[1].type = DOUBLE_PAR;
HPutCPar(proc_handle,1,par,2);

Figure 5.38: Write the control parameter values [6,4.4] using HPutCPar.

5.6 Auxiliary Extension Package Interface Macros and Procedures

In this section, a couple of auxiliary routines are described that facilitate the programming of supply or action
procedures, see figure 5.39.

Names

HCkP, HCkNoObj, HRLDecomp, HNumOfChannels, HIncrRL

Synopsis

#include "Halcon.h"

HCkP( Herror (*proc))

HCkNoObj( Hproc_handle proc_handle)

Herror HRLDecomp( Hrlregion const *reg_in,

int r1,
int c1,
int r2,
int c2,
Hrlregion *reg_inner,
Hrlregion *reg_outer)

HNumOfChannels( Hproc_handle proc_handle,

INT4_8 obj_index,
int *num_channels)

HError HIncrRL( Hproc_handle proc_handle)

Figure 5.39: Auxiliary Extension Package Interface Macros and Procedures.

 5.6.1 HCkP 83

5.6.1 HCkP

The macro HCkP (see figure 5.39) checks the result state of a procedure call. Most of the HALCON procedures are
of the type Herror. For internal HALCON procedures, the result code H_MSG_OK is returned if no error occurred,
see also section 3.7 on page 47. HCkP exits the current procedure if the encapsulated procedure returns any other
error code. Moreover, this error code is returned to the caller of the current procedure.
The macro is used to make source code more compact, but still safe with respect to error handling, see figure 5.40:
Here, the call of the procedure HRLDecomp is encapsulated within the macro. If any error occurs, the procedure
exits with an appropriate error code. Otherwise the processing is continued.
Note that most of the interface routines described in this chapter internally call HCkP, i.e. they exit the current
procedure returning an appropriate error code in case of an error.
Be aware that all memory permanently allocated within a procedure will not be deallocated in case of an
error if you exit the procedure using HCkP. This will lead to memory leaks. !

Herror err;

/* without HCkP: */
err = HRLDecomp(reg_in,r1,c1,r2,c2,
reg_inner,reg_outer);
if (err != H_MSG_OK) return err;

/* with HCkP: */
HCkP(HRLDecomp(reg_in,r1,c1,r2,c2,
reg_inner,reg_outer));

Figure 5.40: Error handling with HCkP.

5.6.2 HCkNoObj

The macro HCkNoObj (see figure 5.39 on page 82) is used to check whether all iconic input parameters of an
operator contain at least one iconic object. Otherwise, the supply procedure is exited with a return code depending

Parameter Handling
on the current setting of no_object_result accessible by the HALCON operators set_system and get_system
(see the Reference Manuals for details). The default setting for no_object_result is H_MSG_TRUE, that means
HCkNoObj reports “no error” in case of empty iconic input parameters. Note that in this case all output parameters
are also empty.
We recommend to call

HCkNoObj(proc_handle);

at the beginning of the supply procedure for every operator with iconic input objects to guarantee the existence of
iconic data to be processed within the operator.

5.6.3 HRLDecomp

HRLDecomp (see figure 5.39 on page 82) is an auxiliary procedure to ease border treatment within the action
procedures of filter operators based on filter masks. It’s prototype is included in hlib\HRLClip.h.
The region (respectively domain or area of definition) reg_in of the image to be processed is split into two parts:
reg_inner and reg_outer. Note that both new regions must have been allocated before, see section 3.2.1 on
page 41.
reg_inner is the original region reg_in minus the pixels around the image border. It contains all pixels within
the rectangle specified by the upper left corner7 (r1,c1) and the lower right corner (r2,c2). These coordinates
7 r1 and r2 denote row coordinates, c1 and c2 column coordinates.
84 Handling Iconic Objects and Control Parameters

Herror IPBFilter(HBYTE *in, /* input image */

Hrlregion *region, /* domain (area of def.) */
int width, /* image size: width */
int height, /* image size: height */
HBYTE *out) /* output image */
{
...
Hrlregion *inner,*outer;

HCkP(HAllocRLNumTmp(proc_handle,&inner,region->num));
HCkP(HAllocRLNumTmp(proc_handle,&outer,region->num*2));
HCkP(HRLDecomp(region,1,1,height-2,width-2,inner,outer));
/* filtering without border treatment */
for (i=0; i<inner->num; i++)
for (k=CB(inner->rl,i,width); k<=CE(inner->rl,i,width); k++)
out[k] = ...
/* filtering with border treatment */
for (i=0; i<outer->num; i++)
for (k=CB(outer->rl,i,width); k<=CE(outer->rl,i,width); k++)
out[k] = ...
HCkP(HFreeRLTmp(proc_handle,outer));
HCkP(HFreeRLTmp(proc_handle,inner));
}

Figure 5.41: Border treatment for a 3 × 3 filter.

should be selected that way, that the filter mask is completely within the image when placed on any pixel inside of
the rectangle. Thus, no border treatment is necessary within reg_in.
reg_out is set to all remaining pixels within reg_in. For those pixels an appropriate (and time consuming) border
treatment has to be performed. Figure 5.41 shows an application of HRLDecomp.
Note that HRLDecomp is no macro, i.e., it does not check the result state of the underlying procedure using HCkP.
! Thus, you must call HCkP on HRLDecomp yourself as shown in the example.
Note that the distinction of “inner” and “outer” area only refers to the image border, but not to the border of the
regions specifying the domain (area of definition). So, it is only ensured that no memory access to positions outside
the image matrix can happen, but there is no guarantee that all pixel values covered by the filter mask when placed
on pixels within reg_inner are defined, if they do not belong to reg_in. This means, a filter might use undefined
gray values along the border of the domain of the input images. The HALCON user should keep that in mind,
when applying a sequence of filters to restricted regions of interest.

5.6.4 HNumOfChannels

HNumOfChannels (see figure 5.39 on page 82) returns for the first input iconic parameter of a HALCON operator
the number of channels of the image object with the index obj_index. Thus, this routine is just a shortcut for
using HPNumOfChannels as defined in figure 5.5 on page 60 with par_num = 1.
Note that HNumOfChannels automatically checks the result state of the underlying procedure with the macro HCkP.
! Thus, you must not use HCkP on HNumOfChannels yourself.

5.6.5 HIncrRL

HIncrRL (see figure 5.39 on page 82) increases the value of the system parameter ’current_runlength_number’
by 50%, not exceeding 2*(width+1)*height, where width and height are the dimensions of the largest image.
These dimensions are accessible using get_system with ’width’ and ’height’ (see the Reference Manuals for
details). Note, DEF_RL_LENGTH can also be increased using set_system.
As a consequence the procedures HAllocRL (page 45), HAllocRLTmp (page 42), and HAllocRLLocal (page 43)
allocate regions of increased size. Figure 5.41 shows an application of HIncrRL.
 5.6.5 HIncrRL 85

Note that HIncrRL is no macro, i.e., it does not check the result state of the underlying procedure using HCkP.
Thus, you must call HCkP on HIncrRL yourself as shown in the example.
!
Hrlregion *region;
Herror err;
HCkP(HAllocRLTmp(proc_handle, &region));
do
{
/* Use HPGetURL instead of HGetURL, to perform explicit error handling. */
err = HPGetURL(proc_handle, 1, region);
if (err == H_ERR_WRRLN2)
/* Number of chords too big, increase /*
{
HCkP(HFreeUpToTmp(proc_handle, region));
HCkP(HIncrRL(proc_handle));
HCkP(HAllocRLTmp(proc_handle, &region));
}
else if (err != H_MSG_OK)
{
HCkP(HFreeRLTmp(proc_handle, region));
return err;
}
} while (err == H_ERR_WRRLN2);

Figure 5.42: Increasing memory allocated for regions.

Parameter Handling
86 Handling Iconic Objects and Control Parameters
 Special Routines for Typical Supply Procedures 87

Special Routines
Chapter 6

Special Routines for Typical Supply

Procedures

In the previous chapter, the basic routines for handling iconic objects, iconic object parameters, and control param-
eters of a HALCON operator have been introduced. Based on these, this chapter describes a set of convenience
routines that facilitate the programming of supply procedures in typical situations.

6.1 Loop Macros

A frequently needed task is to process all image objects (images or regions) passed to an operator by one or two
input iconic object parameters. This is true for most filter and many segmentation operators. Loop macros provide
a framework for this problem, see also section 5.3 on page 65.
The following table contains an overview of all loop macros, their areas of application, and the provided image
data. Their syntax is defined in figure 6.1.

Macro Application Image Data Provided

HAllReg region shape features, region data (Hrlregion) of input image
region transformation, object
binary morphology
HAllSegm gray value features, region and image data (Hrlregion and
segmentation Himage) of input image object
HAllFilter filter, region and image data (Hrlregion and
image transformations Himage) of input image object, image data
structure (Himage) for image output object
HAllFilter2 filter, intersection of the regions of both input im-
segmentation, age objects (Hrlregion), the image data
arithmetic with two input images of both objects, and a image data structure
(Himage) for the image output object

All macros described in this section have in common that they implement a loop over all image objects within the
first input iconic parameter. HAllFilter2 also includes a parallel loop over all objects within the second input
object parameter. It is assumed that the operator does not have any more input iconic parameters. The macros
provide users with the region (domain) and the pixel data of each image object so that they can work on the data
within the loop. Some also create output image objects.
The macros return the index of the current object obj_index (1 . . . n) within the input iconic object parameter.
Thus, obj_index can be seen as a reference parameter of the macro and therefore is notated1 with ’&obj_index’.
The macros return all regions as pointers to the original region data within the HALCON database. So the pro-
grammer is only allowed to read them. The only exception is again HAllFilter2 that computes the intersection
of the region data of both input images and stores it in a new region.
1 Note that this is a specific notation only - do not pass pointers to the macros!
88 Special Routines for Typical Supply Procedures

Names

HAllReg, HAllSegm, HAllFilter, HAllFilter2

Synopsis
#include "Halcon.h"

HAllReg( Hproc_handle proc_handle,

Hrlregion **region,
INT4_8 obj_index)

HAllSegm( Hproc_handle proc_handle,

Hrlregion **region,
Himage *image,
int max_channels,
INT4_8 obj_index)

HAllFilter( Hproc_handle proc_handle,

Hrlregion **region,
Himage *image_in,
Himage *image_out,
int max_channels,
INT4_8 obj_index)

HAllFilter2( Hproc_handle proc_handle,

Hrlregion *region,
Himage *image_in1,
Himage *image_in2,
Himage *image_out,
int max_channels,
INT4_8 obj_index)

Figure 6.1: Convenience loop macros to access iconic objects. “&” denotes output parameters of the macros. This
is only a special notation to make clear that these parameters are changed by the macros. So do not
pass pointers to variables but the variables itself to the macro.

6.1.1 HAllReg
HAllReg (see figure 6.1) implements a loop over all iconic objects of the first input image parameter. For every
object within this parameter, it returns the region of the iconic object (domain) in region2 . All gray value channels
are ignored.
HAllReg is a combination of HAllObj (see section 5.3.1 on page 66) and HGetFDRL (see section 5.2.2 on page
62). It is typically used within feature extraction operators: A list of input regions have to be examined concern-
ing special features. Some HALCON operators of this kind are circularity, area_center, or contlength,
for example . Moreover, it is possible to return new region(s) by using the interface macro HNewRegion (see
section 6.2.1 on page 94) as it is done, for example, by erosion_rectangle1 or shape_trans.
Figure 6.2 illustrates the application of HAllReg showing a complete supply procedure for a hypothetical operator
center that computes the center of gravity of all input regions. The operator has one input iconic object parameter
that exclusively contains regions and two output control parameters for returning the results as tuples of floating-
point numbers (the coordinates of the centers of gravity of all regions). The corresponding DEF file (short version)
might look like this:

center <- CIPCenter[Regions:::Rows$F,Columns$F];

center may be called with one or more regions as input. HAllReg implements a loop over all of them, sets the
loop index i to the current index of the region (1 . . . n), and passes a pointer to the region to the action procedure
that performs the center of gravity. In our case the action procedure is the internal HALCON procedure HRLArea.
The result values are written into two arrays of the type Hcpar and returned by HPutCPar (see section 5.5.15 on
page 80).
2 Remember: HALCON image objects consist of one region specifying the domain (area of definition) and an arbitrary number of gray

value channels containing the pixel data

 6.1.2 HAllSegm 89

Herror CIPCenter(Hproc_handle proc_handle)

{

Special Routines
Hcpar *Row,*Col;
INT4_8 num;
double row,col;
INT4_8 area;
INT4_8 i;
Hrlregion *region;

/* allocate memory corresponding to the number of regions. */

HGetObjNum(proc_handle,1,&num);
HCkP(HAlloc(proc_handle,sizeof(*Row)*num,&Row);
HCkP(HAlloc(proc_handle,sizeof(*Col)*num,&Col);
/* get the regions of all input iconic objects in the first param. */
HAllReg(proc_handle,&region,i)
{
HCkP(HRLArea(proc_handle,region,&area,&row,&col));
Row[i-1].type = DOUBLE_PAR; /* par. type is float */
Row[i-1].par.d = row; /* resulting row */
Col[i-1].type = DOUBLE_PAR; /* par. type is float */
Col[i-1].par.d = col; /* resulting column */
}
HPutPPar(proc_handle,1,Row,i); /* return result */
HPutPPar(proc_handle,2,Col,i); /* return result */
return(H_MSG_TRUE);
}

Figure 6.2: An application of HAllReg: Compute the center of gravity for all input regions in the first input iconic
object parameter.

6.1.2 HAllSegm

HAllSegm (see figure 6.1) extends HAllReg: Not only the region but also all gray value channels of an object within
the first input image object parameter are accessed within a loop. Thus, HAllSegm is a combination/modification of
HAllObj (see section 5.3.1 on page 66), HGetFDRL (see section 5.2.2 on page 62), and HAllComp (see section 5.3.2
on page 66). It is especially useful for segmentation operators (transition of gray value channels to regions). Some
typical HALCON operators that make use of HAllSegm are threshold, regiongrowing, auto_threshold, or
label_to_region.
A HALCON image object (in short a HALCON image) consists of one region (domain) that specifies its area of
definition and of one or more channels (gray value components) containing the pixel data. All channels of an
image are of the same size, but may have different pixel types. The data contained in a channel (pixel type, the
image matrix, etc.) is stored in a structure of type Himage (see section 4.1 on page 49). If the image has only one
channel, the address of a variable of the type Himage is passed to HAllSegm. For multi-channel images an array of
the type Himage[max_channels] must be passed. The maximal number of channels to be accessed by HAllSegm
is specified by the parameter max_channels, see figure 6.3.

Himage images[3];
HAllSegm(proc_handle,region,images,3,i) {
...
Himage image;
HAllSegm(proc_handle,region,&image,1,i) {
...

Figure 6.3: The parameters image and max_channels of HAllSegm.

The parameter max_channels only specifies the maximum number of channels. If an image contains less channels,
the corresponding Himage elements in the image array are undefined. The actual number of channels can be
accessed using HNumOfChannels, for example (see section 5.6.4 on page 84). An image must contain at least one
channel. Otherwise, HAllSegm returns an error. If the number of channels exceeds max_channels, the remaining
90 Special Routines for Typical Supply Procedures

channels are ignored. Furthermore, the size of all channels is checked for equality3 .

Herror IPSegm(Hproc_handle proc_handle, /* HALCON proc. handle */

Hrlregion *region, /* domain (area of definition) */
Himage *image, /* input image */
Hrlregion *out) /* segmentation result */
{
/* compute region "out" from "region" and "image" */
return(H_MSG_OK);
}

Herror CIPSegm(Hproc_handle proc_handle)

{
INT4_8 i;
Hrlregion *region, *new_region;
Himage image;

HCkP(HAllocRLTmp(proc_handle,&new_region)); /* allocate memory*/

HAllSegm(proc_handle,&region,&image,1,i) { /* all inp. images*/
HCkP(IPSegm(region,&image,new_region));
HNewRegion(proc_handle,new_region); /* allocate new */
} /* region */
HCkP(HFreeRLTmp(proc_handle,new_region)); /* free memory */
return(H_MSG_TRUE);
}

Figure 6.4: A typical application of HAllSegm: A segmentation operator.

Figure 6.4 shows a framework for a supply procedure for a segmentation operator using HAllSegm. The cor-
responding hypothetical operator segm has one input object parameter for input images containing at least one
channel. The DEF file (short version) might look like

segm <- CIPSegm[Image:Region::];

The macro HAllSegm used in CIPSegm performs a loop over all image objects within the first input object parame-
ter Image of segm. With every pass of the loop it returns the image data of the current input object in the variables
region (domain) and image (first gray value channel). The results of the segmentation (new_region) are stored
via the macro HNewRegion (see section 6.2.1 on page 94) as new objects of the HALCON database and returned
in the (first) output object parameter (Region). Note that this simple operator has no control parameters.
A new region is allocated for the action procedure via HAllocRLTmp (see section 3.2.1 on page 41) before entering
the loop. This region is used as temporary memory for the computation result and must be deallocated (via
HFreeRLTmp) before exiting the supply procedure.

6.1.3 HAllFilter

HAllFilter (see figure 6.1 on page 88) further extends the loop macros introduced so far: For every input image
object a new output image object is created (and added to the first output object parameter) with
• the same number of channels (components),
• the same pixel type (of the corresponding channels),
• the same image size and
• the same area of definition (region, domain).
Thus, HAllFilter is a combination/modification of HAllObj (see section 5.3.1 on page 66), HGetFDRL (see
section 5.2.2 on page 62), HAllComp (see section 5.3.2 on page 66), HCopyObj (see section 5.4.2 on page 68), and
HPutDImage (see section 5.4.6 on page 70). It has been designed for filter operators that typically create a modified
result image for every input image. The region remains unmodified. Typical examples for this functionality are the
HALCON operators sobel_amp, mean_image, scale_image_max, or texture_laws.
3 Remember: The sizes must be equal, whereas the pixel types of different channels may vary
 6.1.3 HAllFilter 91

Herror IPScaleNew(Hrlregion *region,

Himage *image_in,

Special Routines
Himage *image_out,
{
INT4_8 i,l,end;
double h;

for (i=0; i<region->num; i++) {

end = CE(region->rl,i,image_in->width);
for (l=CB(region->rl,i,image_in->width); l<=end; l++) {
HDFImage(h,image_in,l);
HImageFD(image_out,h*mult,l);
} }
return(H_MSG_OK);
}

Herror CIPScaleNew(Hproc_handle proc_handle)

{
Hcpar mult;
Hrlregion *region;
Himage image_in,image_out;
INT4_8 i;

HGetSPar(proc_handle,1,DOUBLE_PAR,&mult,1);
HAllFilter(proc_handle,&region,&image_in,&image_out,1,i) {
HCkP(IPScaleNew(region,&image_in,mult.par.d,&image_out));
}
return(H_MSG_TRUE);
}

Figure 6.5: A typical application of HAllFilter: A filter operator.

Figure 6.5 shows a typical application of HAllFilter – a hypothetical operator scale_new that multiplies all
gray values of the input objects within the first input object parameter with a constant. The corresponding DEF
file (short version) might look like

scale_new <- CIPScaleNew[Image:ImageScaled:Mult$f:];

The operator has one input object parameter (Image) that contains one or more input image objects (each consisting
of one or more gray value channels and one region as domain, i.e., area of definition). With every pass of the loop
an image object is accessed and its components are transferred to region and image_in, see also HAllSegm in
section 6.1.2 on page 89. These components are passed to the action procedure IPScaleNew. In this example only
the first channel of each input object is used.
HAllFilter also creates output objects (in the HALCON database) to return the modified data. Furthermore, these
objects are added to the list of objects for the first output object parameter (here ImageScaled). Their underlying
image matrices are accessible via image_out. Those are also passed to the action procedure IPScaleNew within
the loop. IPScaleNew calculates the new gray values for all pixels within the domain of the input image and writes
them into the provided image components image_out4 . The regions of the image objects remain unmodified so
that all pixels of output objects lying outside the region are undefined.
Note that HAllFilter creates all necessary image matrices, combines them with the input regions to new image
objects, and returns those in the first output object parameter. So the programmer of the supply procedure needs
not to bother about the handling of image objects etc. To access the input control parameter, HGetSPar (see
section 5.5.8 on page 77) is used in the example.
The structure image_in may contain different pixel types. There are several ways to handle this within an opera-
tor:
1. The simplest method is to implement the operator just for the most common pixel type BYTE_IMAGE and
return an error message (H_ERR_WIT) for any other pixel type.
4 Note that image_out contains a pointer to a pixel matrix with the same size and pixel type as image_in.
92 Special Routines for Typical Supply Procedures

2. Another way is to provide several action procedures – one for every pixel type – and call the appropriate
procedure via switch(image_in.kind).
3. The third (generic) method makes use of the macros HDFImage and HImageFD, see figure 6.6. They
encapsulate the access to gray values by buffering them in a double variable.
By writing pixel values via HImageFD, the double value val is converted into the current pixel type
of image_in (and therefore may be clipped) and stored in the pixel specified by the linear coordinate
lin_coord, see section 4.1 on page 49.
The other way around, the specified pixel value is converted to double and returned in val when using
HDFImage to read image data.
The third method has been used in our example, as it allows a very compact source code. But this variant naturally
shows drawbacks in terms of computation time: Two type conversions have to be computed with every pixel access
and all pixel arithmetic has to be done in double.

Names

HDFImage, HImageFD

Synopsis

#include "Halcon.h"

HDFImage( double &val,

Himage *image,
INT4_8 lin_coord)

HImageFD( Himage *image,

double val,
INT4_8 lin_coord)

Figure 6.6: Auxiliary macros for generic access to pixel data. “&” denotes an output parameter of HDFImage. This
is only a special notation to make clear that this parameter is changed by the macro. So do not pass a
pointer to double but the double variable itself to the macro.

6.1.4 HAllFilter2
The macro HAllFilter2 (see figure 6.1 on page 88) is a variation of HAllFilter introduced in the previous
section. It facilitates the implementation of filters with two input object parameters. Examples for this technique
are the HALCON operators add_image, mult_image, bit_and, and max_image.
HAllFilter2 extends HAllFiter so that with every image object of the first input object parameter also the
corresponding image object (with the same object index obj_index) of the second input object parameter is
provided. Moreover, it checks the image sizes of both image objects for equality. If the sizes are equal, the images
are provided in the loop variables image_in1 and image_in2, otherwise an error is returned.
Moreover, HAllFilter2 computes a new input region (region) by intersecting the domains (areas of definition)
of both input images. Note that memory for this region must have been allocated before (e.g. with HAllocRLTmp).
Furthermore, region must be deallocated at the end of the supply procedure (HFreeRLTmp).
Output image objects are created and returned in the first output object parameter in the same way as described for
HAllFilter in section 6.1.3 on page 90.
Figure 6.7 shows a typical application of HAllFilter2 – the implementation of an operator that adds the gray
values of two input images. As in procedure IPScaleNew in figure 6.5 on page 91, the macros HDFImage and
HImageFD are used to read and write pixel values. This example exhibits the additional advantage that the operator
can even add the gray values of two images with different pixel types.

6.2 Object Generation

This section describes the convenience routines HNewRegion, HPutRect, and HDupObj for creating new image
objects, see figure 6.8.
 6.2 Object Generation 93

Herror IPAddNew(Hproc_handle proc_handle,

Hrlregion *region,

Special Routines
Himage *image_in1,*image_in2,*image_out)
{
INT4_8 i,l,end;
double h1,h2;

for (i=0; i<region->num; i++) {

end = CE(region->rl,i,image_in->width);
for (l=CB(region->rl,i,image_in->width); l<=end; l++) {
HDFImage(h1,image_in1,l);
HDFImage(h2,image_in2,l);
HImageFD(image_out,h1+h2,l);
} }
return(H_MSG_OK);
}

Herror CIPAddNew(Hproc_handle proc_handle)

{
Hrlregion *region;
Himage image_in1,image_in2,image_out;
INT4_8 i;

HCkP(HAllocRLTmp(proc_handle,&region));
HAllFilter2(proc_handle,region,&image_in1,
&image_in2,&image_out,1,i) {
HCkP(IPAddNew(proc_handle,region,&image_in1,
&image_in2,&image_out));
}
HCkP(HFreeRLTmp(proc_handle,region));
return(H_MSG_TRUE);
}

Figure 6.7: A typical application of HAllFilter2.

HNewRegion creates a new image object in the HALCON database encapsulating the specified region and adds
this object to the first output object parameter. HPutRect inserts a rectangular region (as domain, i.e., area of
definition) into an already existing output image object. Finally, HDupObj adds an iconic input object to the object
list of the first output object parameter.

Names

HNewRegion, HPutRect, HDupObj

Synopsis

#include "Halcon.h"

HNewRegion(Hproc_handle proc_handle,
Hrlregion *region)

HPutRect( Hproc_handle proc_handle,

Hkey obj_key,
HIMGDIM width,height)

HDupObj( Hproc_handle proc_handle,

INT4_8 obj_index)

Figure 6.8: Convenience routines for creating output objects.

94 Special Routines for Typical Supply Procedures

6.2.1 HNewRegion

HNewRegion (see figure 6.8) is used to create a new image object in the HALCON database which is also added to
the first output object parameter. It contains a copy of region. It is common to call an image object region, when
only its region component is used.
Note that HNewRegion automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HNewRegion yourself.

Herror CIPConvex(Hproc_handle proc_handle)

{
Hrlregion *region;
Hrlregion *region_new;

HCkP(HAllocRLTmp(proc_handle,&region_new) /* allocate memory */

HAllReg(proc_handle,&region,i) { /* all regions */
HCkP(HRLConvex2(proc_handle,region,region_new));
/* create an output region object (first output param.) */
HNewRegion(proc_handle,region_new);
}
HCkP(HFreeRLTmp(proc_handle,region_new)); /* free memory */
return(H_MSG_TRUE);
}

Figure 6.9: A typical application of HNewRegion: The region transformation “convex hull”.

Typically, HNewRegion is used within segmentation procedures (see figure 6.4 on page 90) and region transforma-
tion procedures such as the procedure CIPConvex shown in figure 6.9. CIPConvex corresponds to a hypothetical
operator trans_convex which might be defined as

trans_convex <- CIPConvex[Region:RegionConvex::];

In the example, all regions within Region are provided in region by HAllReg (see section 6.1.1 on page 88)
one after the other. The internal HALCON procedure HRLConvex2 computes the convex hull for each region and
writes it to region_new. Furthermore, a new region object in the HALCON database is created and added to the
output object parameter RegionConvex.
Note that HNewRegion was also used in the example in figure 6.4 on page 90.

6.2.2 HPutRect

HPutRect (see figure 6.8 on page 93) inserts a rectangular region in an already existing output object with database
key obj_key. It is mostly used in connection with operators that create new image objects like in the example in
figure 6.10.
Note that HPutRect automatically checks the result state of the underlying procedure with the macro HCkP (see
! section 5.6.1 on page 83). Thus, you must not use HCkP on HPutRect yourself.
Note that HCrObj (see section 5.4.1 on page 67) creates an object with empty region. In many situations the default
domain (area of definition) for a new image will be the full image domain, which is a rectangle. In this situation
the use of HPutRect is very convenient.

6.2.3 HDupObj

HDupObj (see figure 6.8 on page 93) is a combination/simplification of HGetObj (see section 5.1.1 on page 57)
and HCopyObj (see section 5.4.2 on page 68). It duplicates iconic input objects (images, regions, XLD) in order
to pass them directly to the first output object parameter. The objects to be duplicated are specified by their index
obj_index within the first input object parameter. Note that this index corresponds to obj_index as defined for
 6.2.3 HDupObj 95

Herror CIOGrabImage(Hproc_handle proc_handle)

{

Special Routines
Hkey obj_key,image_key;
Himage image;

HCrObj(proc_handle,1,&obj_key);
HCkP(HNewImage(proc_handle,&image,BYTE_IMAGE,640,480));
/* grab an NTSC image 640 x 480 pixel, 8 bit */
HCkP(IOBGrabImage(&image));
HPutDImage(proc_handle,obj_key,1,&image,false,&image_key);
HPutRect(proc_id,obj_key,image.width,image.height);
return(H_MSG_TRUE);
}

Figure 6.10: A typical application of HPutRect: Grabbing an image.

the loop macros (HAll*) in section 6.1 on page 87. HDupObj is typically used for operators that examine objects
and select them by a given criterion. Some HALCON operators of this kind are select_shape or select_gray.
Note that HDupObj automatically checks the result state of the underlying procedure with the macro HCkP (see
section 5.6.1 on page 83). Thus, you must not use HCkP on HDupObj yourself.
Figure 6.11 shows an application of HDupObj: CIPUserSelect computes the length of the contour of each input
!
region (in parameter 1). All regions with a contour of at least the minimal length min are passed to the output.

Herror CIPUserSelect(Hproc_handle proc_handle)

{
Hrlregion *region;
Hrlregion *region_new;
double length;
Hcpar min;
INT4_8 i;

HGetSPar(proc_handle,1,DOUBLE_PAR,&min,1); /* get min. length */

HAllReg(proc_handle,&region,i) { /* all regions */
HCkP(HRLContLength(proc_handle,region,&length)); /* length */
if (length >= min.par.d) /* length o.k. ? */
HDupObj(proc_handle,i); /* duplicate object*/
}
return(H_MSG_TRUE);
}

Figure 6.11: A typical application of HDupObj: Duplicate input regions that fulfill a specific criteria (length of contour).

As HDupObj only increases the number of references to a database object instead of copying it physically, its
memory costs and computational costs are neglectable. In contrast, HNewRegion and HAllFilter always allocate
new memory for the output objects, for example. Therefore, use HDupObj whenever possible.
96 Special Routines for Typical Supply Procedures
 Creating a New HALCON Package 97

Chapter 7

Package Creation
Creating a New HALCON Package

This chapter explains step by step how to create a new package. Note that the description often references the
environment variable HALCONARCH, which is set during the installation. For more details about this variable please
refer to the Installation Guide, section 1.4 on page 8.

7.1 The HALCON Compiler hcomp

The HALCON compiler hcomp is the most important tool for creating a new HALCON package. It automati-
cally generates the interface code for the desired host language, the help files, and the documentation files. hcomp
processes DEF files that contain descriptions of all operators as a basic resource, see chapter 2 on page 19. The
HALCON compiler uses the same mechanism for generating the original system operators and user-defined oper-
ators.
The syntax of the hcomp command is as follows:

hcomp <options> <files>

Example:

hcomp -u -H -ppackage MyUserOps.def

The parameter “-u” signals that an interface for user-defined operators should be generated. This parameter can
be omitted as it is the default1 . The option -H generates the main package interface code (Hpackage.c). One or
more definition files that are separated by blanks must be specified as files argument. The extension .def may be
omitted:

hcomp -C -ppackage MyUserOps1 MyUserOps2 MyUserOps3

You either call hcomp in the directory of the DEF files (typically the package subdirectory def) or specify the path
to the DEF files.
To use the package in a programming language, you must also generate the appropriate interface code. In the
example above, the corresponding C files (HCpackage.c and HCpackage.h) are created with the option -C. Their
names depend on the host language and the specified package, not on the names of the input DEF files.

7.1.1 Selection of the Host Language

One call of hcomp can always create only one interface, i.e, the options described as follows can only be switched
on under mutual exclusion. Use
1 Note that hcomp also is used by MVTec to generate the interface code for the normal HALCON system.
98 Creating a New HALCON Package

hcomp -H [-ppackage] <DEF files>

to create the main interface code (Hpackage.c), which is necessary independent whether you want to use the
package in HDevelop or in a programming language.
Additionally, the commands in the following table create the needed files for the corresponding programming
languages.

Language Command Created Files

C hcomp -C [-ppackage] <DEF files> HCpackage.c
HCpackage.h
C++ hcomp -P [-ppackage] <DEF files> HCPPpackage.cpp
HCPPpackage.h
C# hcomp -N [-ppackage] <DEF files> HDOTNETpackage.cs

The generated source files are the basis for the interface libraries, see section 7.2 on page 100.

7.1.2 Creating the Help Files

Help files are necessary for the online access to the operator knowledge base via HALCON operators like
get_operator_info. For example, HDevelop uses their information to build up the menu tree ’Operator’
(chapter and section structuring) and ’Suggestions’ (alternatives, cross references, predecessor, successor, and
keywords). The help files are generated for the language selected with the (optional) -l option. The default
language is English.

hcomp -M -l<language> <DEF files>

creates files with the stem operators_, followed by the language (default: en_US), and the following extensions:

Extension Description
.ref The operator description (text, value lists, . . . ).
.idx Index for every operator specifying the start address of its entry within the *.ref file.
.key List of keywords (index entries) with the associated operators.
.num Specification of the number of parameters per parameter class for every operator.
.sta Specification of the parameter names and the chapter names for every operator.

In addition to the option -M

-c<TAGS-FILE>

can be set in order to insert the source file and the line number of the supply procedure of the operator into the
*.ref file. To do this, a TAGS-File (usually TAGS) must have been generated by the etags command before.

7.1.3 Creating HTML Reference Files

hcomp can generate HTML reference files. Thus, its easy to provide an online documentation of new operators
that can be accessed with an HTML browser. Use
hcomp -R [-p<package>] -l<lang> -a<author-info> -f<copyright-footer> <DEF files>

to create HTML files. Note that the created HTML files contain the information for all programming language
interfaces.
With the (optional) parameters -a and -f you can customize the created manual: The author information passed
with the parameter -a appears on the main HTML page; the string passed with the parameter -f appears at the
bottom of every generated HTML page.
The following files are generated:
 7.1.4 Creating the PDF Reference Manuals 99

• index.html
Home page containing the chapter structure and links to the different (sub-)chapters
(toc_<chapter>_<subchapter>.html)
• index_by_name.html
Alphabetical list of all operators with links to the corresponding operator description pages (files
<operator>.html)
• index_classes.html
List of all classes (for .NET) with links to the corresponding description pages (files <class>.html)
• toc_<chapter>_<subchapter>.html

Package Creation
For every (sub-)chapter: A list of all operators within the chapter with links to the corresponding operator
description pages (files <operator>.html)
• <operator>.html
A description page for each operator
• <class>.html
A description page for each class (for .NET)

7.1.4 Creating the PDF Reference Manuals

hcomp can also generate LATEX files containing the complete reference manuals adapted to the different supported
programming languages, i.e. the description of the operators is provided in a specific syntax. Use

hcomp -Rlatex:<plang> [-p<package>] -l<lang> -a<author-info> -f<copyright-footer> <DEF files>

to create LATEX files. plang can be set to c, cpp, com, dotnet, and hdevelop (HDevelop syntax). hdevelop
is default and may therefore be omitted. The package name specified with [-p] is used for the title page of the
manual.
The information passed with the parameter -a appears in the PDF version of the manual (see below) in the field
“Author” of the dialog describing the document. With the parameter -f you can pass a string, which then appears
on the back side of the title page. A typical use of this parameter is to print a copyright notice.
The generated LATEX files use the package halcon_reference_en_US.sty (or similar for other languages). This
package resides in the directory $HALCONROOT/doc/macros (Linux notation). You must include this directory in
the environment variable TEXINPUTS. If the variable is empty, set it to:

:$HALCONROOT/doc/macros

Otherwise, LATEX will be unable to find it (typical error message: File ’halcon_reference_en_US.sty’ not
found.
The LATEX file(s) can be transformed into PDF files by using pdflatex and makeindex. Note that pdflatex must
be called several times to get the references right; to get a correct table of context and index the sequence of calls
is pdflatex > pdflatex > makeindex > pdflatex > pdflatex.
The generated PDF contains interactive bookmarks and hyperlinks similar to the HTML version (and the author
information passed with the parameter -a). Note that this functionality requires that your LATEX distribution in-
cludes the package hyperref; if this package exists but is too old, a warning will be issued, as this can result in
errors during the LATEX process or in suboptimal PDFs.
For a printer-friendly variant of the PDF file, you can disable the interactive features by modifying the file
index.tex before starting pdflatex: Replace the line (possibly with different language key)

\usepackage[pdflinks]{halcon_reference_en_US}

by

\usepackage{halcon_reference_en_US}
100 Creating a New HALCON Package

If you want to create both documents with and without PDF links, please use different directories or remember to
delete all auxiliary LATEX files before starting to pdflatex the modified index.tex, because the two versions are
not compatible.

7.1.5 Miscellaneous

Here are some more options supported by hcomp:

Option Description
hcomp -i filename <DEF files> Consider only the operators listed in filename.
hcomp -x filename <DEF files> Do not consider the operators listed in filename.

7.2 Generating HALCON Packages

Once the new operators have been described in DEF files and implemented (supply and action procedures) a
couple of dynamic objects (DLLs in Windows, shared libraries in Linux environments, respectively) must be
created. Never change the name of a package or the corresponding names of the libraries/DLLs contained in
a package. These names are encoded within the libraries. If you change the names this information will not match
any longer. Thus, the loader of the operating system will fail to open the dynamic libraries. If you want to rename
a package, you must create the libraries/DLLs again.
To activate a package, its complete path must be added to the environment variable HALCONEXTENSIONS, e.g.,

%HALCONEXAMPLES%\extension_package\halconuser

Please note that the package paths in HALCONEXTENSIONS are separated by semicolons (Windows) or colons
(Linux), see also section 1.3 on page 13.

7.2.1 Creating the Operator Libraries

The supply and action procedures must be encapsulated in a DLL (Windows), shared library (Linux). The name of
this shared object must be consistent with the package name (plus file extension). For the use by HALCON XL, a
second version of the library must be created, with the additional suffix xl to the name. Please refer to section 7.2.6
and the documentation of your programming environment for more details (also about the following sections).
Under Windows the generated DLLs must be placed in the subdirectory bin\%HALCONARCH%, the libraries in the
subdirectory lib\%HALCONARCH%. Under Linux, the generated shared libraries must be placed in the subdirectory
lib/$HALCONARCH, binaries in the subdirectory bin/$HALCONARCH of the package. .NET assemblies must be
placed in the subdirectory bin\dotnet.
Independent of whether you want to use the package in HDevelop or in a programming language, you must create
the main interface library package. This library is based on a single C file Hpackage.c, which is generated via

hcomp -H -ppackage <DEF file(s)>

7.2.2 Creating the C Interface

To access new HALCON operators inside a package within C programs, you must create a C interface library
packagec residing in the subdirectory lib\%HALCONARCH% of the package. This library is based on a single C file
HCpackage.c, which is generated via

hcomp -C -ppackage <DEF file(s)>

from the DEF files of your new operators. Note that hcomp simultaneously generates the file HCpackage.h
containing the C prototypes of your new operators. Include this file in your C programs using these operators.
 7.2.3 Creating the C++ Interface 101

7.2.3 Creating the C++ Interface

To access new HALCON operators inside a package within C++ programs you must create a C++ interface library
packagecpp residing in the subdirectory lib\%HALCONARCH% of the package. This library is based on the file
HCPPpackage.cpp generated via

hcomp -P -ppackage <DEF file(s)>

from the DEF files of your self developed operators. Note that hcomp simultaneously generates the file
HCPPpackage.h containing the C++ prototypes of your new operators. Include this file in your C++ programs

Package Creation
using these operators.

7.2.4 Creating the .NET Interface

To access new HALCON operators inside a package within .NET programs, you must create the interface assembly
packagedotnet residing in the subdirectory lib\dotnet of the package. This assembly is based on the C# source
file HDOTNETpackage.cs, which is generated via

hcomp -N -ppackage <DEF file(s)>

from the DEF files of your new operators.

7.2.5 Creating New Applications

To create new application programs (written in C, C++, or .NET languages) based on your own HALCON oper-
ators, you must link the corresponding language interface libraries packagec or packagecpp to your objects, or
reference the corresponding .NET assembly packagedotnet. For C or C++ applications, you furthermore need
the HALCON library itself and the HALCON/C or HALCON/C++ library (as for any HALCON application). For
.NET applications, you need the HALCON/.NET assembly.

7.2.6 Additional Information for Specific Platforms

The previous sections summarized the generation of HALCON extensions in general. This section contains addi-
tional information for specific platforms. The main differences concern the name handling and the generation of
shared libraries / DLLs.

7.2.6.1 Generating Packages Under Windows

To activate a package, its complete path, e.g.,

%HALCONEXAMPLES%\extension_package\halconuser
must be included in the environment variable HALCONEXTENSIONS. In the Windows version the package paths in
HALCONEXTENSIONS are separated by semicolons.
Note that DLLs must be stored in the subdirectory bin\%HALCONARCH% of the package, the corresponding
libraries in the subdirectory lib\%HALCONARCH%.

• Creating object files for the HALCON XL version:

By default, using CMakeLists.txt, the package will be built with the normal version of HALCON. If you
want to build with HALCON XL, set the option HALCON_XL to ON or 1 in CMake during the configuration
step. For this, use the following syntax:

cmake -DHALCON_XL=1 %HALCONEXAMPLES%\extension_package\halconuser

102 Creating a New HALCON Package

• Creating the operator DLL package.dll and the library package.lib:

To create the operator DLL package.dll containing new HALCON operators and the corresponding library
package.lib, the object files containing the corresponding supply and action procedures and the HALCON
library halcon.lib must be linked.
To create the libraries packagexl.dll and packagexl.lib for HALCON XL, set the option HALCON_XL
to ON or 1 in CMake during the configuration step. The corresponding object files must be linked to the
HALCON XL library halconxl.lib instead of halcon.lib.
• Creating the C interface DLL packagec.dll and the library packagec.lib:
To create the libraries packagec.dll and packagec.lib, which provide the C interface to new HALCON
operators, the object file HCpackage.obj, the new operator library package.lib, the HALCON C library
halconc.lib, and the HALCON library halcon.lib must be linked.
To create the libraries packagecxl.dll and packagecxl.lib for HALCON XL, set the option HALCON_XL
to ON or 1 in CMake during the configuration step. The corresponding object files must be linked to the
HALCON XL version of the libraries, i.e., packagexl.lib, halconcxl.lib, and halconxl.lib.
• Creating the C++ interface DLL packagecpp.dll and the library packagecpp.lib:
To create the DLL packagecpp.dll providing the C++ interface to new HALCON operators and the
corresponding library packagecpp.lib, the object file HCPPpackage.obj, the new operator library
package.lib, the HALCON C++ library halconcpp.lib and the HALCON library halcon.lib must
be linked.
To create the libraries packagecppxl.dll and packagecppxl.lib for HALCON XL, set the option
HALCON_XL to ON or 1 in CMake during the configuration step. The corresponding object files must be linked
to the HALCON XL version of the libraries, i.e., packagexl.lib, halconcppxl.lib, and halconxl.lib.
• Creating the .NET interface assembly packagedotnet.dll:
The assembly packagedotnet.dll providing the .NET interface to new HALCON operators is created
directly from the source file HDOTNETpackage.cs, together with the XML file that documents the content
of the assembly.
To create the assembly packagedotnetxl.dll for HALCON XL, set the option HALCON_XL to ON or 1 in
CMake during the configuration step.
• Creating new applications:
To create new application programs written in C or C++, you must link packagec.lib or packagecpp.lib
to your objects. Furthermore, you will need halconc.lib or halconcpp.lib (as for any HALCON ap-
plication). For .NET applications, you reference the libraries packagex.lib and halconx.lib or the
assemblies packagedotnet.dll and halcondotnet.dll, respectively.
To create a HALCON XL version of your application, just use the HALCON XL version of the libraries
(e.g., packagecxl.lib and halconcxl.lib in case of a C application).
To be able to link the package DLL to your application program, the complete DLL file path of the new
package, e.g.,
%HALCONEXAMPLES%\extension_package\halconuser\bin\%HALCONARCH%
has to be added to the environment variable PATH. This is also true for .NET applications.
Do not copy a package DLL into the Windows system directories, as it would be loaded twice in this
case!
If you encounter program crashes, check the stack size allocated by your application. A stack size of 6 to 8
MB is recommended.

The directory %HALCONEXAMPLES%\extension_package\halconuser contains the example CMake file

CMakeLists.txt, which can be used to create the example package halconuser and the example applications
based on the package halconuser. If required, download CMake (version 3.7.1 or later) from the CMake website
and install it. To build the example package halconuser using CMake, do the following:
 7.2.6 Additional Information for Specific Platforms 103

mkdir build
cd build
cmake -DCMAKE_INSTALL_PREFIX=%HALCONEXAMPLES%\extension_package \
HALCONEXAMPLES%\extension_package\halconuser
cmake --build . --target install

By default, the normal version of HALCON is created. If you want to build using HALCON XL, set the option
HALCON_XL to ON or 1 in CMake during the configuration step.

Package Creation
7.2.6.2 Generating Packages Under Linux

To activate a package, its complete path, e.g.,

$HALCONEXAMPLES/extension_package/halconuser
must be included in the environment variable HALCONEXTENSIONS. In the Linux version, the package paths in
HALCONEXTENSIONS are separated by colons. Please see also the comments on installing a HALCON package on
a Linux system in section 1.3.2 on page 14.
• Compiling the source code:
To generate shared libraries, you must produce position-independent code. For the gcc/g++ com-
piler, this is done using the option -fPIC. For gcc, we also recommend the options -march=pentium
-mcpu=pentiumpro -ansi -fno-strict-prototype.
• Creating object files for the HALCON XL version:
By default, using CMakeLists.txt, the package will be built with the normal version of HALCON. If you
want to build with HALCON XL, set the option HALCON_XL to ON or 1 in CMake during the configuration
step. For this, use the following syntax:
cmake -DHALCON_XL=1 %HALCONEXAMPLES%\extension_package\halconuser

• Creating the operator library libpackage.so:

To create the operator library libpackage.so containing new HALCON operators, the object files contain-
ing the corresponding supply and action procedures must be linked. The linkage of shared libraries is done
with ld -shared. Specify the desired name libpackage.so and location of the library with the ld option
-o.
To create the library libpackagexl.so for HALCON XL, set the option HALCON_XL to ON or 1 in CMake
during the configuration step. The corresponding object files must be linked.
• Creating the C interface library libpackagec.so:
To create the C interface library libpackagec.so providing the interface to new HALCON operators, the
object file HCpackage.o and the new operator library libpackage.so must be linked.
To create the library libpackagecxl.so for HALCON XL, set the option HALCON_XL to ON or 1 in CMake
during the configuration step. The corresponding object file must be linked to the HALCON XL version of
the operator library, i.e., libpackagexl.so.
• Creating the C++ interface library libpackagecpp.so:
To create the C++ interface library libpackagecpp.so providing the interface to new HALCON operators,
the object files HCPPpackage.o and HCPPpackageGlobal.o, and the new operator lib libpackage.so
must be linked.
To create the library libpackagecppxl.so for HALCON XL, set the option HALCON_XL to ON or 1 in
CMake during the configuration step. The corresponding object files must be linked to the HALCON XL
version of the operator library, i.e., libpackage.so.
• Creating the .NET interface assembly packagedotnet.dll:
You can use the Mono compiler to create the assembly packagedotnet.dll providing the .NET interface
to new HALCON operators. This assembly is based on the C# source file HDOTNETpackage.cs, see sec-
tion 7.2.4 on page 101. Note that you need a successfully installed and configured version of Mono to create
the assembly.
104 Creating a New HALCON Package

For this, run the following commands in a shell:

mcs HDOTNETpackage.cs /target:library /out:Hpackage.dll /doc:Hpackage.xml /warn:1 -r:halcondotnet.dll

To create an executable you have to reference the new created assembly Hpackage.dll and the HALCON
.NET assembly as well.
• Creating new applications:
To create new application programs written in C or C++, you must link libpackage.so and
libpackagec.so or libpackagecpp.so to your objects (besides libhalcon.so and libhalconc.so or
libhalconcpp.so as for any HALCON application). For .NET applications, you reference the assemblies
packagedotnet.dll and halcondotnet.dll.
Furthermore, you must add the package library subdirectory lib/$HALCONARCH to the environment variable
LD_LIBRARY_PATH.
To create a HALCON XL version of your application, just use the HALCON XL version of the libraries
(e.g., libpackagexl.so, libpackagecxl.so, libhalconxl.so, and libhalconcxl.so in case of a C
application).

7.3 HALCON Directories

HALCON always presumes that the environment variable HALCONROOT contains the path of the HALCON instal-
lation directory. The following subdirectories are important for creating a new system:

• include
HALCON include files for compiling
• lib\%HALCONARCH%
HALCON libraries
• dotnet20,dotnet35
HALCON/.NET assemblies for the different versions of the .NET Framework (for more information, see the
Programmer’s Guide, table 10.1 on page 64)
• bin\%HALCONARCH%
HALCON compiler hcomp, under Windows also the HALCON DLLs
• doc\macros
LATEX files for generating PDF reference files or manuals

The environment variable HALCONEXAMPLES contains the path of the HALCON programming examples. The
following subdirectory is useful for creating a new system:

• extension_package\halconuser
Example for a HALCON extension package
 HALCON Error Codes 105

Appendix A

HALCON Error Codes

In this section all HALCON error codes are summarized, see also section 3.7 on page 47.

Error Name Code Description

Error Codes
H_ERR_WIPT1 1201 Wrong type of control parameter 1
H_ERR_WIPT2 1202 Wrong type of control parameter 2
H_ERR_WIPT3 1203 Wrong type of control parameter 3
H_ERR_WIPT4 1204 Wrong type of control parameter 4
H_ERR_WIPT5 1205 Wrong type of control parameter 5
H_ERR_WIPT6 1206 Wrong type of control parameter 6
H_ERR_WIPT7 1207 Wrong type of control parameter 7
H_ERR_WIPT8 1208 Wrong type of control parameter 8
H_ERR_WIPT9 1209 Wrong type of control parameter 9
H_ERR_WIPT10 1210 Wrong type of control parameter 10
H_ERR_WIPT11 1211 Wrong type of control parameter 11
H_ERR_WIPT12 1212 Wrong type of control parameter 12
H_ERR_WIPT13 1213 Wrong type of control parameter 13
H_ERR_WIPT14 1214 Wrong type of control parameter 14
H_ERR_WIPT15 1215 Wrong type of control parameter 15
H_ERR_WIPT16 1216 Wrong type of control parameter 16
H_ERR_WIPT17 1217 Wrong type of control parameter 17
H_ERR_WIPT18 1218 Wrong type of control parameter 18
H_ERR_WIPT19 1219 Wrong type of control parameter 19
H_ERR_WIPT20 1220 Wrong type of control parameter 20
H_ERR_WIPV1 1301 Wrong value of control parameter 1
H_ERR_WIPV2 1302 Wrong value of control parameter 2
H_ERR_WIPV3 1303 Wrong value of control parameter 3
H_ERR_WIPV4 1304 Wrong value of control parameter 4
H_ERR_WIPV5 1305 Wrong value of control parameter 5
H_ERR_WIPV6 1306 Wrong value of control parameter 6
H_ERR_WIPV7 1307 Wrong value of control parameter 7
H_ERR_WIPV8 1308 Wrong value of control parameter 8
H_ERR_WIPV9 1309 Wrong value of control parameter 9
H_ERR_WIPV10 1310 Wrong value of control parameter 10
H_ERR_WIPV11 1311 Wrong value of control parameter 11
H_ERR_WIPV12 1312 Wrong value of control parameter 12
H_ERR_WIPV13 1313 Wrong value of control parameter 13
H_ERR_WIPV14 1314 Wrong value of control parameter 14
H_ERR_WIPV15 1315 Wrong value of control parameter 15
H_ERR_WIPV16 1316 Wrong value of control parameter 16
H_ERR_WIPV17 1317 Wrong value of control parameter 17
H_ERR_WIPV18 1318 Wrong value of control parameter 18
106 HALCON Error Codes

Error Name Code Description

H_ERR_WIPV19 1319 Wrong value of control parameter 19

H_ERR_WIPV20 1320 Wrong value of control parameter 20
H_ERR_WCOMP 1350 Wrong value of component (see reset_obj_db())
H_ERR_WGCOMP 1351 Wrong value of gray value component (see reset_obj_db())
H_ERR_WIPN1 1401 Wrong number of values of control parameter 1
H_ERR_WIPN2 1402 Wrong number of values of control parameter 2
H_ERR_WIPN3 1403 Wrong number of values of control parameter 3
H_ERR_WIPN4 1404 Wrong number of values of control parameter 4
H_ERR_WIPN5 1405 Wrong number of values of control parameter 5
H_ERR_WIPN6 1406 Wrong number of values of control parameter 6
H_ERR_WIPN7 1407 Wrong number of values of control parameter 7
H_ERR_WIPN8 1408 Wrong number of values of control parameter 8
H_ERR_WIPN9 1409 Wrong number of values of control parameter 9
H_ERR_WIPN10 1410 Wrong number of values of control parameter 10
H_ERR_WIPN11 1411 Wrong number of values of control parameter 11
H_ERR_WIPN12 1412 Wrong number of values of control parameter 12
H_ERR_WIPN13 1413 Wrong number of values of control parameter 13
H_ERR_WIPN14 1414 Wrong number of values of control parameter 14
H_ERR_WIPN15 1415 Wrong number of values of control parameter 15
H_ERR_WIPN16 1416 Wrong number of values of control parameter 16
H_ERR_WIPN17 1417 Wrong number of values of control parameter 17
H_ERR_WIPN18 1418 Wrong number of values of control parameter 18
H_ERR_WIPN19 1419 Wrong number of values of control parameter 19
H_ERR_WIPN20 1420 Wrong number of values of control parameter 20
H_ERR_IONTB 1500 Number of input objects too big
H_ERR_WION1 1501 Wrong number of values of object parameter 1
H_ERR_WION2 1502 Wrong number of values of object parameter 2
H_ERR_WION3 1503 Wrong number of values of object parameter 3
H_ERR_WION4 1504 Wrong number of values of object parameter 4
H_ERR_WION5 1505 Wrong number of values of object parameter 5
H_ERR_WION6 1506 Wrong number of values of object parameter 6
H_ERR_WION7 1507 Wrong number of values of object parameter 7
H_ERR_WION8 1508 Wrong number of values of object parameter 8
H_ERR_WION9 1509 Wrong number of values of object parameter 9
H_ERR_OONTB 1510 Number of output objects too big
H_ERR_BREAK 20 Operator canceled by user
H_ERR_WNP 2000 Wrong specification of parameter (error in file: xxx.def)
H_ERR_HONI 2001 Initialize HALCON: reset_obj_db(Width,Height,Components)
H_ERR_WRKNN 2002 Used number of symbolic object names too big
H_ERR_LIC_NO_LICENSE 2003 No license found
H_ERR_LIC_NO_MODULES 2005 No modules in license (invalid VENDOR_STRING)
H_ERR_LIC_NO_LIC_OPER 2006 No license for this operator
H_ERR_LIC_BADPLATFORM 2008 Vendor keys do not support this platform
H_ERR_LIC_BADVENDORKEY 2009 Bad vendor keys
H_ERR_LIC_BADSYSDATE 2021 System clock has been set back. This error can only occur
when the FEATURE line contains an expiration date
H_ERR_LIC_BAD_VERSION 2022 Invalid format for version argument
H_ERR_LIC_CANTCONNECT 2024 Cannot establish a connection with a license server
H_ERR_LIC_MAXSESSIONS 2028 Maximum session limit reached
H_ERR_LIC_MAXUSERS 2029 All licenses in use
H_ERR_LIC_NO_SERVER_IN_FILE 2030 No license server specified for floating license
H_ERR_LIC_NOFEATURE 2031 Can not find feature in the license file
H_ERR_LIC_OLDVER 2033 License file does not support a version this new
H_ERR_LIC_PLATNOTLIC 2034 This platform not authorized by license - running on platform
not included in PLATFORMS list
 107

Error Name Code Description

H_ERR_LIC_SERVBUSY 2035 License server busy - the request should be retried (this is a
rare occurrence)
H_ERR_LIC_NOCONFFILE 2036 could not find license file
H_ERR_LIC_BADFILE 2037 Invalid license file syntax
H_ERR_LIC_NOSERVER 2038 Cannot connect to a license server
H_ERR_LIC_NOTTHISHOST 2041 Invalid host
H_ERR_LIC_LONGGONE 2042 Feature has expired
H_ERR_LIC_BADDATE 2043 Invalid date format in license file
H_ERR_LIC_BADCOMM 2044 Invalid returned data from license server
H_ERR_LIC_BADHOST 2045 Cannot resolve server name
H_ERR_LIC_CANTWRITE 2047 Cannot write data to license server
H_ERR_LIC_SERVLONGGONE 2051 License server does not support this version of this feature
H_ERR_LIC_TOOMANY 2052 Request for more licenses than this feature supports
H_ERR_LIC_CANTFINDETHER 2055 Cannot find ethernet device
H_ERR_LIC_NOREADLIC 2056 Cannot read license file
H_ERR_LIC_DATE_TOOBIG 2067 Date too late for binary format
H_ERR_LIC_NOSERVRESP 2069 Server did not respond to message

Error Codes
H_ERR_LIC_SETSOCKFAIL 2075 setsockopt() failed
H_ERR_LIC_BADCHECKSUM 2076 Message checksum failure
H_ERR_LIC_INTERNAL_ERROR 2082 Internal licensing error
H_ERR_LIC_NOSERVCAP 2087 Server does not support this request
H_ERR_LIC_POOL 2091 This feature is available in a different license pool
H_ERR_HEN_CANCEL 21 Operator canceled
H_ERR_WOOPI 2100 Wrong index for output object parameter
H_ERR_WIOPI 2101 Wrong index for input object parameter
H_ERR_WOI 2102 Wrong index for image object (too big or too small)
H_ERR_WRCN 2103 Wrong number region/image component (see: HGetComp)
H_ERR_WRRN 2104 Wrong relation name
H_ERR_AUDI 2105 Access to undefined gray value component
H_ERR_WIWI 2106 Wrong image width
H_ERR_WIHE 2107 Wrong image height
H_ERR_ICUNDEF 2108 Undefined gray value component
H_ERR_CANCEL 22 Operator canceled by interrupt_operator
H_ERR_IDBD 2200 Inconsistent data of data base (typing)
H_ERR_WICPI 2201 Wrong index for input control parameter
H_ERR_DBDU 2202 Data of data base not defined (internal error)
H_ERR_PNTL 2203 Number of operators too big
H_ERR_UEXTNI 2205 User extension not properly installed
H_ERR_NPTL 2206 Number of packages too large
H_ERR_NSP 2207 No such package installed
H_ERR_ICHV 2211 Incompatible HALCON versions
H_ERR_ICOI 2212 Incompatible operator interface
H_ERR_XPKG_WXID 2220 Wrong extension package id
H_ERR_XPKG_WOID 2221 Wrong operator id
H_ERR_XPKG_WOIID 2222 Wrong operator information id
H_ERR_TIMEOUT_BREAK 23 Operator canceled by userset timeout
H_ERR_LIC_NODONGLE 2300 Dongle not attached, or can’t read dongle
H_ERR_LIC_NODONGLEDRIVER 2301 Missing Dongle Driver
H_ERR_LIC_TIMEOUT 2318 Timeout
H_ERR_LIC_INVALID_CERTIFICATE 2321 License server certificate invalid
H_ERR_LIC_INVALID_TLS_CERTIFICATE 2335 License server SSL/TLS certificate invalid
H_ERR_LIC_BAD_ACTREQ 2339 Invalid activation request received
H_ERR_LIC_NOT_ALLOWED 2345 Specified operation is not allowed
H_ERR_LIC_ACTIVATION 2348 Activation error
H_ERR_LIC_NO_CM_RUNTIME 2379 No CodeMeter Runtime installed (version 6.30 or later
required)
108 HALCON Error Codes

Error Name Code Description

H_ERR_LIC_CM_RUNTIME_TOO_OLD 2380 Installed version of CodeMeter Runtime is too old (version

6.30 or later required)
H_ERR_LIC_WRONG_EDITION 2381 License is for wrong edition of HALCON
H_ERR_LIC_UNKNOWN_FLAGS 2382 License contains unknown FLAGS
H_ERR_LIC_PREVIEW_EXPIRED 2383 HALCON preview version expired
H_ERR_LIC_NEWVER 2384 License file does not support a version this old
H_ERR_CTPL_WTYP 2400 Wrong Hctuple element type
H_ERR_CPAR_WTYP 2401 Wrong Hcpar parameter type
H_ERR_CTPL_WIDX 2402 Wrong Hctuple index
H_ERR_WFV 2403 Unsupported file version
H_ERR_WRONG_HANDLE_TYPE 2404 Invalid handle type
H_ERR_WVTYP 2410 Wrong vector type
H_ERR_WVDIM 2411 Wrong vector dimension
H_ERR_WHDL 2450 Wrong (unknown) HALCON handle
H_ERR_WID 2451 Wrong HALCON id, no data available
H_ERR_IDOOR 2452 HALCON id out of range
H_ERR_HANDLE_NULL 2453 HALCON handle is NULL
H_ERR_HANDLE_CLEARED 2454 HALCON handle was already cleared
H_ERR_HANDLE_NOSER 2455 HALCON handle of this type cannot be serialized
H_ERR_HANDLE_CYCLES 2456 Cyclic references of handles were detected
H_ERR_WT_CTRL_EXPECTED 2460 Type mismatch: expected control value, got iconic value
H_ERR_WT_ICONIC_EXPECTED 2461 Type mismatch: expected iconic value, got control value
H_ERR_XPI_INIT_NOT_CALLED 2500 Init function of an HALCON extension that was build with
the hlibxpi interface was not called (check for correct hlibxpi
export)
H_ERR_XPI_NO_INIT_FOUND 2501 Init function of the required HALCON extension was not
found (old interface without hlibxpi support or the hlibxpi ex-
port failed)
H_ERR_XPI_UNRES 2502 Function call in HALCON extension couldn’t be resolved via
hlibxpi
H_ERR_XPI_HLIB_TOO_OLD 2503 The version of the HALCON library is too old for the required
HALCON extension
H_ERR_XPI_XPI_TOO_OLD 2504 The required HALCON extension uses an hlibxpi version that
is no longer supported by the current HALCON version
H_ERR_XPI_MAJOR_TOO_SMALL 2505 The current HALCON version uses an hlibxpi version that
is not supported by the required HALCON extension (major
number too small)
H_ERR_XPI_MINOR_TOO_SMALL 2506 The current HALCON version uses an hlibxpi version that
is not supported by the required HALCON extension (minor
number too small)
H_ERR_XPI_INT_WRONG_MAJOR 2507 Internal error: wrong version number in hlibxpi symbol list
H_ERR_XPI_UNKNOW_HLIB_VER 2508 hlibxpi cannot connect to hlib: unknown hlib version
H_ERR_HW_WFF 2800 Wrong hardware knowledge file format
H_ERR_HW_WFV 2801 Wrong hardware knowledge file version
H_ERR_HW_RF 2802 Error while reading the hardware knowledge
H_ERR_HW_WF 2803 Error while writing the hardware knowledge
H_ERR_HW_TF 2804 Tag in hardware knowledge file not found
H_ERR_HW_CPU 2805 No CPU information in hardware knowledge file found
H_ERR_HW_AOP 2806 No aop information in hardware knowledge file found
H_ERR_HW_HVAR 2807 No aop information for this HALCON variant found
H_ERR_HW_HARCH 2808 No aop information for this HALCON architecture found
H_ERR_HW_HOP 2809 No aop information for specified Operator found
H_ERR_HW_WAOPM 2810 Unknown aop model
H_ERR_HW_WTD 2811 Wrong tag derivate in hardware knowledge file
H_ERR_HW_IE 2812 Internal error while processing hardware knowledge
H_ERR_HW_CANCEL 2813 Optimizing aop was canceled
H_ERR_GV_WA 2830 Wrong access to global variable
H_ERR_GV_NC 2831 Used global variable does not exist
 109

Error Name Code Description

H_ERR_GV_NG 2832 Used global variable not accessible via GLOBAL_ID

H_ERR_HM_NT 2835 HALCON server to terminate is still working on a job
H_ERR_HM_NA 2837 No such HALCON software agent
H_ERR_AG_CN 2838 Hardware check for parallelization not possible on a single-
processor machine
H_ERR_AG_NC 2839 Sequential HALCON does not support parallel hardware check
(use Parallel HALCON instead)
H_ERR_AG_IN 2840 Initialization of agent failed
H_ERR_AG_NT 2841 Termination of agent failed
H_ERR_AG_HW 2842 Inconsistent hardware description file
H_ERR_AG_II 2843 Inconsistent agent information file
H_ERR_AG_IK 2844 Inconsistent agent knowledge file
H_ERR_AG_WV 2845 The file with the parallelization information does not match to
the currently HALCON version/revision
H_ERR_AG_WH 2846 The file with the parallelization information does not match to
the currently used machine
H_ERR_AG_KC 2847 Inconsistent knowledge base of HALCON software agent
H_ERR_AG_CT 2848 Unknown communication type

Error Codes
H_ERR_AG_MT 2849 Unknown message type for HALCON software agent
H_ERR_AG_WK 2850 Error while saving the parallelization knowledge
H_ERR_AG_WW 2851 Wrong type of work information
H_ERR_AG_WA 2852 Wrong type of application information
H_ERR_AG_WE 2853 Wrong type of experience information
H_ERR_AG_NU 2854 Unknown name of HALCON software agent
H_ERR_AG_NE 2855 Unknown name and communication address of HALCON
software agent
H_ERR_AG_RR 2856 CPU representative (HALCON software agent) not reachable
H_ERR_AG_CR 2857 CPU refuses work
H_ERR_AG_RN 2858 Description of scheduling resource not found
H_ERR_AG_TILT 2859 Not accessible function of HALCON software agent
H_ERR_WRT 2860 Wrong type: HALCON scheduling resource
H_ERR_WRS 2861 Wrong state: HALCON scheduling resource
H_ERR_UNKPT 2862 Unknown parameter type: HALCON scheduling resource
H_ERR_UNKPARVAL 2863 Unknown parameter value: HALCON scheduling resource
H_ERR_CTRL_WPP 2864 Wrong post processing of control parameter
H_ERR_GETTI 2867 Error while trying to get time (time query)
H_ERR_GETCPUNUM 2868 Error while trying to get the number of processors
H_ERR_TMPFNF 2869 Error while accessing temporary file
H_ERR_MQCNCL 2890 Message queue wait operation canceled
H_ERR_MQOVL 2891 Message queue overflow
H_ERR_MQCLEAR 2892 Threads still wait on message queue while clearing it
H_ERR_M_WRFILE 2893 Invalid file format for a message
H_ERR_DICT_KEY 2894 Dictionary does not contain requested key
H_ERR_DICT_TUPLE_LENGTH 2895 Tuple in dictionary has incorrect length
H_ERR_DICT_TUPLE_TYPE 2896 Tuple in dictionary is of incorrect type
H_ERR_DICT_INVALID_INDEX 2897 Invalid index for dict tuple
H_ERR_PTHRD_SCHED 2900 Error while forcing a context switch
H_ERR_SCHED_GAFF 2901 Error while accessing the CPU affinity
H_ERR_SCHED_SAFF 2902 Error while setting the CPU affinity
H_ERR_CO_WSO 2950 Wrong synchronization object
H_ERR_CO_WOCO 2952 Wrong thread object
H_ERR_CO_IOPNI 2953 Input Object was not initialized
H_ERR_CO_ICPNI 2954 Input control parameter is not initialized
H_ERR_CO_OOPNI 2955 Output Object parameter is not initialized
H_ERR_CO_OCPNI 2956 Output control parameter is not initialized
H_ERR_PTHRD_CR 2970 creation of pthread failed
H_ERR_PTHRD_DT 2971 pthread-detach failed
110 HALCON Error Codes

Error Name Code Description

H_ERR_PTHRD_JO 2972 pthread-join failed

H_ERR_PTHRD_MI 2973 Initialization of mutex variable failed
H_ERR_PTHRD_MD 2974 Deletion of mutex variable failed
H_ERR_PTHRD_ML 2975 Lock of mutex variable failed
H_ERR_PTHRD_MU 2976 Unlock of mutex variable failed
H_ERR_PTHRD_CS 2977 Failed to signal pthread condition variable
H_ERR_PTHRD_CW 2978 Failed to wait for pthread condition variable
H_ERR_PTHRD_CI 2979 Failed to init pthread condition variable
H_ERR_PTHRD_CD 2980 Failed to destroy pthread condition variable
H_ERR_PTHRD_ES 2981 Failed to signal event
H_ERR_PTHRD_EW 2982 Failed to wait for an event
H_ERR_PTHRD_EI 2983 Failed to init an event
H_ERR_PTHRD_ED 2984 Failed to destroy an event
H_ERR_PTHRD_TSDC 2985 Failed to create a tsd key
H_ERR_PTHRD_TSDS 2986 Failed to set a tsd key
H_ERR_PTHRD_TSDG 2987 Failed to get a tsd key
H_ERR_PTHRD_TSDF 2988 Failed to free a tsd key
H_ERR_PTHRD_BA 2989 Aborted waiting at a barrier
H_ERR_DCDG_FLE 2990 ’Free list’ is empty while scheduling
H_ERR_MSG_PNCI 2991 Communication partner not checked in
H_ERR_MSG_CSAI 2992 You can not start the communication system while running it
H_ERR_MSG_CSNI 2993 Communication partner not checked in
H_ERR_PTHRD_BI 2994 Failed to init a barrier
H_ERR_PTHRD_BW 2995 Failed to wait at a barrier
H_ERR_PTHRD_BD 2996 Failed to destroy a barrier
H_ERR_RCOIMA 3010 Region completely outside of the image domain
H_ERR_ROOIMA 3011 Region (partially) outside of the definition range of the image
H_ERR_RIEI 3012 Intersected definition range region / image empty
H_ERR_EDEF 3013 Image with empty definition range (=> no gray values)
H_ERR_IIEI 3014 No common image point of two images
H_ERR_FLTS 3015 Wrong region for image (first row < 0)
H_ERR_LLTB 3016 Wrong region for image (column in last row >= image width)
H_ERR_UENOI 3017 Number of images unequal in input parameters
H_ERR_HTS 3018 Image height too small
H_ERR_WTS 3019 Image width too small
H_ERR_CHSEG 3020 Internal error: multiple call of HRLInitSeg()
H_ERR_RLSEG1 3021 Internal error: HRLSeg() not initialized
H_ERR_WGAUSSM 3022 Wrong size of filter for Gauss
H_ERR_FSEIS 3033 Filter size exceeds image size
H_ERR_FSEVAN 3034 Filter size have to be odd
H_ERR_FSTOBIG 3035 Filter is too big
H_ERR_EMPTREG 3036 Input region is empty
H_ERR_DOM_DIFF 3037 Domains of the input images differ
H_ERR_ROWTB 3040 Row value of a coordinate > 2ˆ30-1
H_ERR_ROWTS 3041 Row value of a coordinate < -2ˆ30+1
H_ERR_COLTB 3042 Column value of a coordinate > 2ˆ30-1
H_ERR_COLTS 3043 Column value of a coordinate < -2ˆ30+1
H_ERR_WRTHR 3100 Wrong segmentation threshold
H_ERR_UNKF 3101 Unknown feature
H_ERR_UNKG 3102 Unknown gray value feature
H_ERR_EINCC 3103 Internal error in HContCut
H_ERR_EINCP1 3104 Error in HContToPol: distance of points too big
H_ERR_EINCP2 3105 Error in HContToPol: contour too long
H_ERR_TMR 3106 Too many rows (IPImageTransform)
H_ERR_SFZ 3107 Scaling factor = 0.0 (IPImageScale)
H_ERR_OOR 3108 Wrong range in transformation matrix
 111

Error Name Code Description

H_ERR_NEF 3109 Internal error in IPvvf: no element free

H_ERR_NOOB 3110 Number of input objects is zero
H_ERR_EMPOB 3111 At least one input object has an empty region
H_ERR_NPOT 3112 Operation allowed for rectangular images 2**n only
H_ERR_TMEP 3113 Too many relevant points (IPHysterese)
H_ERR_LTB 3114 Number of labels in image too big
H_ERR_NNLA 3115 No labels with negative values allowed
H_ERR_WFS 3116 Wrong filter size (too small?)
H_ERR_IWDS 3117 Images with different image size
H_ERR_IWTL 3118 Target image too wide or too far on the right
H_ERR_IWTS 3119 Target image too narrow or too far on the left
H_ERR_IHTL 3120 Target image too high or too far down
H_ERR_IHTS 3121 Target image too low or too far up
H_ERR_DNOC 3122 Number of channels in the input parameters are different
H_ERR_WRCFAFLT 3123 Wrong color filter array type
H_ERR_WRCFAINT 3124 Wrong color filter array interpolation
H_ERR_NO_AFFTRANS 3125 Homogeneous matrix does not represent an affine

Error Codes
transformation
H_ERR_INPNOBDRY 3126 Inpainting region too close to the image border
H_ERR_DSIZESD 3127 Source and destination differ in size
H_ERR_TMFEAT 3128 To many Features
H_ERR_AXIS_UNDEF 3129 Reflection axis undefined
H_ERR_COWTS 3131 Coocurrence matrix: too little columns for quantization
H_ERR_COHTS 3132 Coocurrence matrix: too little rows for quantization
H_ERR_NUM_COLMN 3133 Wrong number of columns
H_ERR_NUM_LINES 3134 Wrong number of rows
H_ERR_OVL 3135 Number has too many digits
H_ERR_NOT_SYM 3136 Matrix is not symmetric
H_ERR_NUM_COLS 3137 Matrix is too big
H_ERR_SYNTAX 3138 Wrong structure of file
H_ERR_MISSING 3139 Lesser than 2 matrices
H_ERR_COOC_MEM 3140 Not enough memory
H_ERR_NO_FILE 3141 Can not read the file
H_ERR_FILE_WR 3142 Can not open file for writing
H_ERR_NUM_LUCOLS 3143 Too many lookup table colors
H_ERR_WNOLI 3145 Too many Hough points (lines)
H_ERR_DITS 3146 Target image has got wrong height (not big enough)
H_ERR_WINTM 3147 Wrong interpolation mode
H_ERR_THICK_NK 3148 Region not compact or not connected
H_ERR_WIND3 3170 Wrong filter index for filter size 3
H_ERR_WIND5 3171 Wrong filter index for filter size 5
H_ERR_WIND7 3172 Wrong filter index for filter size 7
H_ERR_WLAWSS 3173 Wrong filter size; only 3/5/7
H_ERR_NE_NPTS 3175 Number of suitable pixels too small to reliably estimate the
noise
H_ERR_WNEE 3200 Different number of entries/exits in HContCut
H_ERR_REF 3201 Reference to the underlying contour is missing
H_ERR_XLDWT 3250 Wrong XLD type
H_ERR_XLD_RPF 3252 Internal error: border point is set to FG
H_ERR_XLD_MCL 3253 Internal error: maximum contour length exceeded
H_ERR_XLD_MCN 3254 Internal error: maximum number of contours exceeded
H_ERR_XLD_CTS 3255 Contour too short for operator
H_ERR_XLD_CRD 3256 Regression parameters of contours already computed
H_ERR_XLD_CRND 3257 Regression parameters of contours not yet entered! Please
compute them by calling regress_cont_xld
H_ERR_DBXC 3258 Data base: XLD object has been deleted
112 HALCON Error Codes

Error Name Code Description

H_ERR_DBWXID 3259 Data base: object has no XLD-ID

H_ERR_XLD_WNP 3260 Internal error: wrong number of contour points allocated
H_ERR_XLD_CAND 3261 Contour attribute not defined
H_ERR_FIT_ELLIPSE 3262 Ellipse fitting failed
H_ERR_FIT_CIRCLE 3263 Circle fitting failed
H_ERR_FIT_CLIP 3264 All points classified as outliers (ClippingFactor too small or
used points not similar to primitive)
H_ERR_FIT_QUADRANGLE 3265 Quadrangle fitting failed
H_ERR_INCOMPL_RECT 3266 No points found for at least one side of the rectangle
H_ERR_XLD_COI 3267 A contour point lies outside of the image
H_ERR_FIT_NOT_ENOUGH_POINTS 3274 Not enough valid points for fitting the model
H_ERR_NWF 3275 No ARC/INFO world file
H_ERR_NAIGF 3276 No ARC/INFO generate file
H_ERR_DXF_UEOF 3278 Unexpected end of file while reading DXF file
H_ERR_DXF_CRGC 3279 Cannot read DXF-group code from file
H_ERR_DXF_INAPP 3280 Inconsistent number of attributes per point in DXF file
H_ERR_DXF_INAPPN 3281 Inconsistent number of attributes and names in DXF file
H_ERR_DXF_INAPCN 3282 Inconsistent number of global attributes and names in DXF file
H_ERR_DXF_CRAPP 3283 Cannot read attributes from DXF file
H_ERR_DXF_CRAPC 3284 Cannot read global attributes from DXF file
H_ERR_DXF_CRAN 3285 Cannot read attribute names from DXF file
H_ERR_DXF_WPN 3286 Wrong generic parameter name
H_ERR_DXF_IEDT 3289 Internal DXF I/O error: Wrong data type
H_ERR_XLD_ISOL_POINT 3290 Isolated point while contour merging
H_ERR_NURBS_CCBF 3291 Constraints (MaxError/MaxDistance) cannot be fulfilled
H_ERR_NSEG 3292 No segment in contour
H_ERR_NO_ONE_P 3293 Only one or no point in template contour
H_ERR_SESF 3300 Syntax error in file for training
H_ERR_TMFE 3301 Maximum number of attributes per example exceeded
H_ERR_OPSF 3302 Not possible to open file for training
H_ERR_TMSS 3303 Too many data sets for training
H_ERR_TMSAM 3305 Too many examples for one data set for training
H_ERR_TMCLS 3306 Too many classes
H_ERR_TMBOX 3307 Maximum number of cuboids exceeded
H_ERR_OPCF 3308 Not possible to open classificator’s file
H_ERR_SCLA 3309 Error while saving the classificator
H_ERR_OPF 3310 Not possible to open protocol file
H_ERR_CLEX 3311 Classificator with this name is already existent
H_ERR_TMCLA 3312 Maximum number of classificators exceeded
H_ERR_CNTL 3313 Name of classificator is too long, >= 20
H_ERR_CLNNF 3314 Classificator with this name is not existent
H_ERR_NCCLA 3315 Current classificator is not defined
H_ERR_CLASS2_ID 3316 Wrong id in classification file
H_ERR_CLASS2_VERS 3317 The version of the classifier is not supported
H_ERR_CLASS_NOSITEM 3318 Serialized item does not contain a valid classifier
H_ERR_TM_NO_CL 3319 Text model does not contain a classifier yet (use
set_text_model_param)
H_ERR_KNN_CANNOT_ADD 3320 Adding new features is not possible, because the dataset has
been normalized during training. Please create a new classfier
and add all training data again or disable normalization during
training
H_ERR_ML_KMEAN_INITIALIZATION_ERROR 3325 Error in cluster initialization of the K-Mean algorithm
H_ERR_GMM_NOTRAINFILE 3330 Invalid file format for GMM training samples
H_ERR_GMM_WRTRAINVERS 3331 The version of the GMM training samples is not supported
H_ERR_GMM_WRSMPFORMAT 3332 Wrong training sample format
H_ERR_GMM_NOCLASSFILE 3333 Invalid file format for Gaussian Mixture Model (GMM)
 113

Error Name Code Description

H_ERR_GMM_WRCLASSVERS 3334 The version of the Gaussian Mixture Model (GMM) is not
supported
H_ERR_GMM_TRAIN_UNKERR 3335 Internal error while training the GMM
H_ERR_GMM_TRAIN_COLLAPSED 3336 Singular covariance matrix
H_ERR_GMM_TRAIN_NOSAMPLE 3337 No samples for at least one class
H_ERR_GMM_TRAIN_FEWSAMPLES 3338 Too few samples for at least one class
H_ERR_GMM_NOTTRAINED 3340 GMM has not been trained yet
H_ERR_GMM_NOTRAINDATA 3341 No training samples stored in the classifier
H_ERR_GMM_NOSITEM 3342 Serialized item does not contain a valid Gaussian Mixture
Model (GMM)
H_ERR_MLP_UNKOUTFUNC 3350 Unknown output function
H_ERR_MLP_NOT01ENC 3351 Target vector not in 0-1 encoding
H_ERR_MLP_NOTRAINDATA 3352 No training samples stored in the classifier
H_ERR_MLP_NOTRAINFILE 3353 Invalid file format for MLP training samples
H_ERR_MLP_WRTRAINVERS 3354 The version of the MLP training samples is not supported
H_ERR_MLP_WRSMPFORMAT 3355 Wrong training sample format
H_ERR_MLP_NOCLASSIF 3356 MLP is not a classifier; use OutputFunction = ’softmax’ in
create_class_mlp

Error Codes
H_ERR_MLP_NOCLASSFILE 3357 Invalid file format for multilayer perceptron (MLP)
H_ERR_MLP_WRCLASSVERS 3358 The version of the multilayer perceptron (MLP) is not
supported
H_ERR_WRNUMCHAN 3359 Wrong number of image channels
H_ERR_MLP_WRNUMPARAM 3360 Number of MLP parameters too large
H_ERR_MLP_NOSITEM 3361 Serialized item does not contain a valid multilayer perceptron
(MLP)
H_ERR_LUT_WRNUMCHAN 3370 The number of image channels and the number of dimensions
of the look-up table do not match
H_ERR_LUT_NRCHANLARGE 3371 A look-up table can be build only for a 2 or 3 channel classifier
H_ERR_LUT_CANNOTCREAT 3372 Cannot create a look-up table. Please choose a larger
’bit_depth’ or select ’fast’ for ’class_selection’
H_ERR_SVM_NOTRAINDATA 3380 No training samples stored in the classifier
H_ERR_SVM_NOTRAINFILE 3381 Invalid file format for SVM training samples
H_ERR_SVM_WRTRAINVERS 3382 The version of the SVM training samples is not supported
H_ERR_SVM_WRSMPFORMAT 3383 Wrong training sample format
H_ERR_SVM_NOCLASSFILE 3384 Invalid file format for support vector machine (SVM)
H_ERR_SVM_WRCLASSVERS 3385 The version of the support vector machine (SVM) is not
supported
H_ERR_SVM_WRNRCLASS 3386 Wrong number of classes
H_ERR_SVM_NU_TOO_BIG 3387 Nu was chosen too big
H_ERR_SVM_TRAIN_FAIL 3388 SVM training failed
H_ERR_SVM_DO_NOT_FIT 3389 Old SVM and new SVM do not match
H_ERR_SVM_NO_TRAIN_ADD 3390 SVM contains no trained support vectors
H_ERR_SVM_KERNELNOTRBF 3391 Kernel is not an RBF kernel
H_ERR_SVM_NO_TRAIND_FOR_CLASS 3392 Train data does not contain all classes
H_ERR_SVM_NOT_TRAINED 3393 SVM not trained
H_ERR_NOT_TRAINED 3394 Classifier not trained
H_ERR_SVM_NOSITEM 3395 Serialized item does not contain a valid support vector machine
(SVM)
H_ERR_ROTNR 3401 Wrong rotation number
H_ERR_GOL 3402 Wrong letter for Golay element
H_ERR_BEZ 3403 Wrong reference point
H_ERR_ITER 3404 Wrong number of iterations
H_ERR_MOSYS 3405 Morphology: system error
H_ERR_ART 3406 Wrong type of boundary
H_ERR_OBJI 3407 Morphology: wrong number of input objects
H_ERR_OBJO 3408 Morphology: wrong number of output objects
H_ERR_PARI 3409 Morphology: wrong number of input control parameter
H_ERR_PARO 3410 Morphology: wrong number of output control parameter
114 HALCON Error Codes

Error Name Code Description

H_ERR_SELC 3411 Morphology: structuring element is infinite

H_ERR_WRNSE 3412 Morphology: wrong name for structuring element
H_ERR_WRRLN1 3500 Wrong number of run length rows (chords): smaller than 0
H_ERR_WRRLN2 3501 Number of chords too big. Increase ’cur-
rent_runlength_number’ using set_system!
H_ERR_WRRLL 3502 Run length row with negative length
H_ERR_RLLTB 3503 Run length row >= image height
H_ERR_RLLTS 3504 Run length row < 0
H_ERR_RLCTB 3505 Run length column >= image width
H_ERR_RLCTS 3506 Run length column < 0
H_ERR_CHLTB 3507 For CHORD_TYPE: Number of row too big
H_ERR_CHLTS 3508 For CHORD_TYPE: Number of row too small
H_ERR_CHCTB 3509 For CHORD_TYPE: Number of column too big
H_ERR_MRLE 3510 Exceeding the maximum number of run lengths while auto-
matical expansion
H_ERR_ICCOMPL 3511 Internal error: Region->compl neither true/false
H_ERR_RLEMAX 3512 Internal error: Region->max_num < Region->num
H_ERR_WRRLN3 3513 Internal error: number of chords too big for num_max
H_ERR_OPNOCOMPL 3514 Operator cannot be implemented for complemented regions;
intersect the region with a finite region or set clip_region to
true with set_system
H_ERR_WIMAW1 3520 Image width must be positive
H_ERR_WIMAW2 3521 Image width > MAX_FORMAT
H_ERR_WIMAH1 3522 Image height must be positive
H_ERR_WIMAH2 3523 Image height > MAX_FORMAT
H_ERR_WIMAW3 3524 Image width <= 0
H_ERR_WIMAH3 3525 Image height <= 0
H_ERR_TMS 3550 Too many segments
H_ERR_NO_INT8_IMAGE 3551 ’int8’ images are available on 64 bit systems only
H_ERR_POINT_AT_INFINITY 3600 Point at infinity cannot be converted to a Euclidean point
H_ERR_ML_NO_COVARIANCE 3601 Covariance matrix could not be determined
H_ERR_RANSAC_PRNG 3602 RANSAC algorithm didn’t find enough point correspondences
H_ERR_RANSAC_TOO_DIFFERENT 3603 RANSAC algorithm didn’t find enough point correspondences
H_ERR_PTI_FALLBACK 3604 Internal diagnosis: fallback method had to be used
H_ERR_PTI_TRAFO_SING 3605 Projective transformation is singular
H_ERR_PTI_MOSAIC_UNDERDET 3606 Mosaic is under-determined
H_ERR_COV_NPD 3607 Input covariance matrix is not positive definite
H_ERR_TOO_MANY_POINTS 3608 Number of input points too large
H_ERR_INPC 3620 Inconsistent number of point correspondences
H_ERR_NOPA 3621 At least one image cannot be reached from the reference image
H_ERR_IINE 3622 The image with specified index does not exist
H_ERR_NOCM 3623 Matrix is not a camera matrix
H_ERR_SKNZ 3624 Skew is not zero
H_ERR_ILFL 3625 Illegal focal length
H_ERR_KANZ 3626 Distortion is not zero
H_ERR_VARA 3627 It is not possible to determine all parameters for variable cam-
era parameters
H_ERR_LVDE 3628 No valid implementation selected
H_ERR_KPAR 3629 Kappa can only be determined with the gold-standard method
H_ERR_IMOD 3630 Conflicting number of images and projection mode
H_ERR_PNIC 3631 Error in projection: Point not in any cube map
H_ERR_NO_SOL 3632 No solution found
H_ERR_TINZ 3633 Tilt is not zero
H_ERR_ILMD 3640 Illegal combination of estimation method and parameters to be
determined
H_ERR_NOFFTOPT 3650 Invalid file format for FFT optimization data
H_ERR_WRFFTOPTVERS 3651 The version of the FFT optimization data is not supported
 115

Error Name Code Description

H_ERR_WRHALCONVERS 3652 Optimization data was created with a different HALCON vari-
ant (Sequential HALCON / Parallel HALCON)
H_ERR_OPTFAIL 3653 Storing of the optimization data failed
H_ERR_FFTOPT_NOSITEM 3654 Serialized item does not contain valid FFT optimization data
H_ERR_RDS_NSC 3660 No contours suitable for self-calibration found
H_ERR_RDS_NSS 3661 No stable solution found: please change the inlier threshold or
select contours manually
H_ERR_RDS_ISS 3662 Unstable solution: please choose more or different contours
H_ERR_RDS_NEC 3663 Not enough contours for calibration: please select contours
manually
H_ERR_INVLD_DISP_RANGE 3690 Disparity range exceeds the maximum permitted
H_ERR_EPIINIM 3700 Epipoles are within the image domain: no rectification possible
H_ERR_EPI_FOV 3701 Fields of view of both cameras do not intersect each other
H_ERR_EPI_RECT 3702 The stereo rectification is impossible
H_ERR_BI_WT_TARGET 3710 Wrong type of parameter target_thickness
H_ERR_BI_WT_THICKNESS 3711 Wrong type of parameter thickness_tolerance
H_ERR_BI_WT_POSITION 3712 Wrong type of parameter position_tolerance
H_ERR_BI_WT_SIGMA 3713 Wrong type of parameter sigma

Error Codes
H_ERR_BI_WV_SIGMA 3714 Wrong value of parameter sigma
H_ERR_BI_WT_THRESH 3715 Wrong type of parameter threshold
H_ERR_BI_WV_TARGET 3716 Wrong value of parameter target_thickness
H_ERR_BI_WV_THICKNESS 3717 Wrong value of parameter thickness_tolerance
H_ERR_BI_WV_POSITION 3718 Wrong value of parameter position_tolerance
H_ERR_BI_WV_THRESH 3719 Wrong value of parameter threshold
H_ERR_BI_WT_REFINE 3720 Wrong type of parameter refinement
H_ERR_BI_WV_REFINE 3721 Wrong value of parameter refinement
H_ERR_BI_WT_RESOL 3722 Wrong type of parameter resolution
H_ERR_BI_WV_RESOL 3723 Wrong value of parameter resolution
H_ERR_BI_WT_POLARITY 3724 Wrong type of parameter polarity
H_ERR_BI_WV_POLARITY 3725 Wrong value of parameter polarity
H_ERR_SOL_EMPTY_MODEL_LIST 3751 No sheet-of-light model available
H_ERR_SOL_WNIW 3752 Wrong input image size (width)
H_ERR_SOL_WNIH 3753 Wrong input image size (height)
H_ERR_SOL_WPROF_REG 3754 The bounding-box around the profile region does not fit the
domain of definition of the input image
H_ERR_SOL_CAL_NONE 3755 Calibration extend not set
H_ERR_SOL_UNDEF_DISPARITY 3756 Undefined disparity image
H_ERR_SOL_UNDEF_DISPDOMAIN 3757 Undefined domain for disparity image
H_ERR_SOL_UNDEF_CAMPAR 3758 Undefined camera parameter
H_ERR_SOL_UNDEF_LPCS 3759 Undefined pose of the light plane
H_ERR_SOL_UNDEF_CCS 3760 Undefined pose of the camera coordinate system
H_ERR_SOL_UNDEF_CCS_2_LPCS 3761 Undefined transformation from the coordinate system of the
camera to the coordinate system of the light plane
H_ERR_SOL_UNDEF_MOV_POSE 3762 Undefined movement pose for xyz calibration
H_ERR_SOL_WV_SCALE 3763 Wrong value of scale parameter
H_ERR_SOL_WV_PAR_NAME 3764 Wrong parameter name
H_ERR_SOL_WT_METHOD 3765 Wrong type of parameter method
H_ERR_SOL_WT_AMBIGUITY 3766 Wrong type of parameter ambiguity
H_ERR_SOL_WT_SCORE_TYPE 3767 Wrong type of parameter score
H_ERR_SOL_WT_CALIBRATION 3768 Wrong type of parameter calibration
H_ERR_SOL_WT_NUM_PROF 3769 Wrong type of parameter number_profiles
H_ERR_SOL_WT_CAM_PAR 3770 Wrong type of element in parameter camera_parameter
H_ERR_SOL_WT_PAR_POSE 3771 Wrong type of element in pose
H_ERR_SOL_WV_METHOD 3772 Wrong value of parameter method
H_ERR_SOL_WT_THRES 3773 Wrong type of parameter min_gray
H_ERR_SOL_WV_AMBIGUITY 3774 Wrong value of parameter ambiguity
H_ERR_SOL_WV_SCORE_TYPE 3775 Wrong value of parameter score_type
116 HALCON Error Codes

Error Name Code Description

H_ERR_SOL_WV_CALIBRATION 3776 Wrong value of parameter calibration

H_ERR_SOL_WV_NUM_PROF 3777 Wrong value of parameter number_profiles
H_ERR_SOL_WV_CAMERA_TYPE 3778 Wrong type of camera
H_ERR_SOL_WN_CAM_PAR 3779 Wrong number of values of parameter camera_parameter
H_ERR_SOL_WN_POSE 3780 Wrong number of values of parameter pose
H_ERR_SOL_NO_TARGET_FOUND 3781 Calibration target not found
H_ERR_SOL_NO_VALID_SOL 3782 The calibration algorithm failed to find a valid solution
H_ERR_SOL_WT_CALIB_OBJECT 3783 Wrong type of parameter calibration_object
H_ERR_SOL_INVALID_CALIB_OBJECT 3784 Invalid calibration object
H_ERR_SOL_NO_CALIB_OBJECT_SET 3785 No calibration object set
H_ERR_SOL_WR_FILE_FORMAT 3786 Invalid file format for sheet-of-light model
H_ERR_SOL_WR_FILE_VERS 3787 The version of the sheet-of-light model is not supported
H_ERR_SOL_CAMPAR_UNSUPPORTED 3788 Camera type not supported by calibrate_sheet_of_light_model
H_ERR_SOL_PAR_CALIB 3790 Parameter does not match the set ’calibration’
H_ERR_SOL_WGV_DISP 3791 The gray values of the disparity image, which specify rows in
the camera image, do not fit the height of the camera
H_ERR_TI_WRONGMODEL 3800 Texture inspection model has the wrong type
H_ERR_TI_NOTTRAINED 3801 Texture inspection model is not trained
H_ERR_TI_NOTRAINDATA 3802 Texture inspection model has no training data
H_ERR_TI_NOTRAINFILE 3803 Invalid file format for a texture inspection model
H_ERR_TI_WRTRAINVERS 3804 The version of the texture inspection model is not supported
H_ERR_TI_WRSMPFORMAT 3805 Invalid file format for the training samples
H_ERR_TI_WRSMPVERS 3806 The version of the training sample file is not supported
H_ERR_TI_WRIMGSIZE 3807 At least one of the images within the texture inspection model
is too small
H_ERR_TI_WRSMPTEXMODEL 3808 The read samples do not match the current texture model
H_ERR_NOT_ENOUGH_IMAGES 3809 The texture model does not contain any images
H_ERR_SING 3850 The light source positions are linearly dependent
H_ERR_FEWIM 3851 No sufficient image indication
H_ERR_ZBR_NOS 3852 Internal error: Function has equal signs in HZBrent
H_ERR_DIMK 3900 Kalman: Dimension n,m or p has got a undefined value
H_ERR_NOFILE 3901 Kalman: File does not exist
H_ERR_FF1 3902 Kalman: Error in file (row of dimension)
H_ERR_FF2 3903 Kalman: Error in file (row of marking)
H_ERR_FF3 3904 Kalman: Error in file (value is no float)
H_ERR_NO_A 3905 Kalman: Matrix A is missing in file
H_ERR_NO_C 3906 Kalman: Matrix C is missing in file
H_ERR_NO_Q 3907 Kalman: Matrix Q is missing in file
H_ERR_NO_R 3908 Kalman: Matrix R is missing in file
H_ERR_NO_GU 3909 Kalman: G or u is missing in file
H_ERR_NOTSYMM 3910 Kalman: Covariant matrix is not symmetric
H_ERR_SINGU 3911 Kalman: Equation system is singular
H_ERR_SLM_NOT_PERSISTENT 3950 Feature or operation available only in ’persistent’ mode
H_ERR_SLM_MSW_TOO_LARGE 3951 ’min_stripe_width’ is too large for the selected ’pattern_width’
and/or ’pattern_height’
H_ERR_SLM_SSW_TOO_LARGE 3952 ’single_stripe_width’ is too large for the selected ’pat-
tern_width’ and/or ’pattern_height’
H_ERR_SLM_MSW_GT_SSW 3953 ’min_stripe_width’ has to be smaller or equal
’single_stripe_width’
H_ERR_SLM_SSW_LT_MSW 3954 ’single_stripe_width’ is too small for the selected
’min_stripe_width’
H_ERR_SLM_NOT_PREP 3955 The structured light model can only be decoded after calling
’gen_structured_light_pattern’
H_ERR_SLM_NO_OBJS 3956 The structured light model does not contain the queried object
H_ERR_SLM_WRVERS 3957 The version of the structured light model is not supported
H_ERR_SLM_WRFILE 3958 Invalid file format for a structured light model
H_ERR_SLM_WRONGPATTERN 3959 Parameter does not match the set ’pattern_type’
 117

Error Name Code Description

H_ERR_SLM_NOT_DECODED 3960 ’defect_image’ can only be computed after calling

’decode_structured_light_pattern’
H_ERR_SLM_WRONGMODEL 3961 The structured light model has the wrong type
H_ERR_SLM_WNUMCAMS 3962 The camera setup model has to contain two sets of camera
parameters
H_ERR_SLM_WPATTSIZE 3963 ’pattern_width’ and ’pattern_height’ do not match the projec-
tor parameters in the set ’camera_setup_model’
H_ERR_SLM_WRONGCTYPE 3964 Camera type not supported by the structured light model
H_ERR_SLM_WRONGPTYPE 3965 Projector type not supported by the structured light model
H_ERR_SLM_NO_CSM 3966 The structured light model does not contain a camera setup
model
H_ERR_SLM_NO_VERT 3967 ’pattern_orientation’ does not contain vertical orientation
H_ERR_SLM_NOT_DEC_REC 3968 ’reconstruct_surface_structured_light’ can only be called after
’decode_structured_light_pattern’
H_ERR_SLM_WCAMSIZE 3969 Size of correspondence image does not match the camera pa-
rameters in the set ’camera_setup_model’
H_ERR_DBOIT 4050 Image data management: object is an object tuple
H_ERR_DBOC 4051 Image data management: object has been deleted already
4052 Image data management: wrong object-ID

Error Codes
H_ERR_DBWOID
H_ERR_DBTC 4053 Image data management: object tuple has been deleted already
H_ERR_DBWTID 4054 Image data management: wrong object tuple-ID
H_ERR_DBTIO 4055 Image data management: object tuple is an object
H_ERR_DBIDNULL 4056 Image data management: object-ID is NULL (0)
H_ERR_WDBID 4057 Image data management: object-ID outside the valid range
H_ERR_DBIC 4058 Image data management: access to deleted image
H_ERR_DBWIID 4059 Image data management: access to image with wrong key
H_ERR_DBRC 4060 Image data management: access to deleted region
H_ERR_DBWRID 4061 Image data management: access to region with wrong key
H_ERR_WCHAN 4062 Image data management: wrong value for image channel
H_ERR_DBITL 4063 Image data management: index too big
H_ERR_DBIUNDEF 4064 Image data management: index not defined
H_ERR_NO_OPENCL 4100 No OpenCL available
H_ERR_OPENCL_ERROR 4101 OpenCL Error occurred
H_ERR_NO_COMPUTE_DEVICES 4102 No compute device available
H_ERR_NO_DEVICE_IMPL 4103 No device implementation for this parameter
H_ERR_OUT_OF_DEVICE_MEM 4104 Out of compute device memory
H_ERR_INVALID_SHAPE 4105 Invalid work group shape
H_ERR_INVALID_DEVICE 4106 Invalid compute device
H_ERR_CUDA_ERROR 4200 CUDA Error occurred
H_ERR_CUDNN_ERROR 4201 cuDNN Error occurred
H_ERR_CUBLAS_ERROR 4202 cuBLAS Error occurred
H_ERR_BATCH_SIZE_NOT_SUPPORTED 4203 Setting the batch size on CPUs is not supported. For more
information, please read the documentation of the parameter
H_ERR_CUDA_NOT_AVAILABLE 4204 CUDA implementations are not available
H_ERR_CUDNN_UNSUPPORTED_VERSION 4205 Unsupported version of cuDNN
H_ERR_CUDNN_FEATURE_NOT_SUPPORTED 4206 Current configuration requests a feature not supported by
cuDNN. Use different input size and/or the batch size!
H_ERR_CUDA_DRIVER_VERSION 4207 Your graphics driver does not support the required CUDA ver-
sion. Please update your graphics driver!
H_ERR_TRAINING_UNSUPPORTED 4301 Training is unsupported with the selected runtime.
H_ERR_CPU_INFERENCE_NOT_AVAILABLE 4302 CPU based inference is not supported on this platform
H_ERR_DNNL_ERROR 4303 Error occurred in DNNL library
H_ERR_HAI2_ERROR 4320 Error occurred in an AI Accelerator Interface
H_ERR_HAI2_INVALID_PARAM 4321 Invalid parameter for AI Accelerator Interface
H_ERR_ACL_ERROR 4400 Error occurred in ACL library
H_ERR_VISUALIZATION 4500 Internal visualization error
H_ERR_COLOR_TYPE_UNEXP 4501 Unexpected color type
H_ERR_NUM_COLOR_EXCEEDED 4502 Number of color settings exceeded
118 HALCON Error Codes

Error Name Code Description

H_ERR_WSCN 5100 Wrong (logical) window number

H_ERR_DSCO 5101 Error while opening the window
H_ERR_WWC 5102 Wrong window coordinates
H_ERR_NWA 5103 It is not possible to open another window
H_ERR_DNA 5104 Device or operator not available
H_ERR_UCOL 5105 Unknown color
H_ERR_NWO 5106 No window has been opened for desired action
H_ERR_WFM 5107 Wrong filling mode for regions (fill or margin)
H_ERR_WGV 5108 Wrong gray value (0..255)
H_ERR_WPV 5109 Wrong pixel value (use value of get_pixel(P) only)
H_ERR_WLW 5110 Wrong line width (see: query_line_width(Min,Max))
H_ERR_WCUR 5111 Wrong name of cursor
H_ERR_WLUT 5112 Wrong color table (see: query_lut(Name)
H_ERR_WDM 5113 Wrong representation mode (see: query_insert(Mode))
H_ERR_WRCO 5114 Wrong representation color (see: query_color(List))
H_ERR_WRDM 5115 Wrong dither matrix (binary image representation)
H_ERR_WRIT 5116 Wrong image transformation (name or image size)
H_ERR_IPIT 5117 Unsuitable image type for image transformation
H_ERR_WRZS 5118 Wrong zooming factor for image transformation
H_ERR_WRDS 5119 Wrong representation mode
H_ERR_WRDV 5120 Wrong code of device
H_ERR_WWINF 5121 Wrong number for father window
H_ERR_WDEXT 5122 Wrong window size
H_ERR_WWT 5123 Wrong window type
H_ERR_WND 5124 No current window has been set
H_ERR_WRGB 5125 Wrong color combination or range (RGB)
H_ERR_WPNS 5126 Wrong number of pixels set
H_ERR_WCM 5127 Wrong value for comprise (object or image)
H_ERR_FNA 5128 set_fix with 1/4 image levels and static not valid
H_ERR_LNFS 5129 set_lut not valid in child windows
H_ERR_LOFL 5130 Number of concurrent used color tables is too big
H_ERR_WIDT 5131 Wrong device for window dump
H_ERR_WWDS 5132 Wrong window size for window dump
H_ERR_NDVS 5133 System variable DISPLAY (setenv) not defined
H_ERR_WBW 5134 Wrong thickness for window margin
H_ERR_WDVS 5135 System variable DISPLAY has been set wrong (<host>:0.0)
H_ERR_TMF 5136 Too many fonts loaded
H_ERR_WFN 5137 Wrong font name
H_ERR_WCP 5138 No valid cursor position
H_ERR_NTW 5139 Window is not a textual window
H_ERR_NPW 5140 Window is not a image window
H_ERR_STL 5141 String too long or too high
H_ERR_NSS 5142 Too little space in the window rightwards
H_ERR_NMS 5143 Window is not suitable for the mouse
H_ERR_DWNA 5144 Here Windows on a equal machine is permitted only
H_ERR_WOM 5145 Wrong mode while opening a window
H_ERR_WWM 5146 Wrong window mode for operation
H_ERR_LUTF 5147 Operation not possible with fixed pixel
H_ERR_LUTN8 5148 Color tables for 8 image levels only
H_ERR_WTCM 5149 Wrong mode for pseudo real colors
H_ERR_WIFTL 5150 Wrong pixel value for LUT
H_ERR_WSOI 5151 Wrong image size for pseudo real colors
H_ERR_HRLUT 5152 Error in procedure HRLUT
H_ERR_WPFSL 5153 Wrong number of entries in color table for set_lut
H_ERR_WPVS 5154 Wrong values for image area
H_ERR_WLPN 5155 Wrong line pattern
 119

Error Name Code Description

H_ERR_WLPL 5156 Wrong number of parameters for line pattern

H_ERR_WNOC 5157 Wrong number of colors
H_ERR_WPST 5158 Wrong value for mode of area creation (0,1,2)
H_ERR_SWNA 5159 Spy window is not set (set_spy)
H_ERR_NSFO 5160 No file for spy has been set (set_spy)
H_ERR_WSPN 5161 Wrong parameter output depth (set_spy)
H_ERR_WIFFD 5162 Wrong window size for window dump
H_ERR_WLUTF 5163 Wrong color table: wrong file name or query_lut()
H_ERR_WLUTE 5164 Wrong color table: empty string?
H_ERR_WLUTD 5165 Using this hardware set_lut(’default’) is allowed only
H_ERR_CNDP 5166 Error while calling online help
H_ERR_LNPR 5167 Row can not be projected
H_ERR_NFSC 5168 Operation is unsuitable using a computer with fixed color table
H_ERR_NACD 5169 Computer represents gray scales only (no colors)
H_ERR_LUTO 5170 LUT of this display is full
H_ERR_WCC 5171 Internal error: wrong color code
H_ERR_WWATTRT 5172 Wrong type for window attribute

Error Codes
H_ERR_WWATTRN 5173 Wrong name for window attribute
H_ERR_WRSPART 5174 Negative height of area (or 0)
H_ERR_WCSPART 5175 Negative width of area (or 0)
H_ERR_WNCV 5176 Window not completely visible
H_ERR_FONT_NA 5177 Font not allowed for this operation
H_ERR_WDIFFTH 5178 Operation not possible (window was created in different
thread)
H_ERR_DEPTH_NOT_STORED 5179 Depth was not stored with window
H_ERR_CHA3 5180 Internal error: only RGB-Mode
H_ERR_NMWA 5181 No more (image-)windows available
H_ERR_INDEX_NOT_STORED 5182 Object index was not stored with window
H_ERR_PRIM_NO_POINTS 5183 Operator does not support primitives without point coordinates
H_ERR_REMOTE_DESKTOP_SIZE 5184 Maximum image size for Windows Remote Desktop exceeded
H_ERR_NOGL 5185 No OpenGL support available
H_ERR_NODEPTH 5186 No depth information available
H_ERR_OGL_ERROR 5187 OpenGL error occurred
H_ERR_UNSUPPORTED_FBO 5188 Required framebuffer object is unsupported
H_ERR_OGL_HSR_NOT_SUPPORTED 5189 OpenGL accelerated hidden surface removal not supported on
this machine
H_ERR_WP_IWP 5190 Invalid window parameter
H_ERR_WP_IWPV 5191 Invalid value for window parameter
H_ERR_UMOD 5192 Unknown mode
H_ERR_ATTIMG 5193 No image has been previously attached to window
H_ERR_OBJ_ATTACHED 5194 The drawing object has already been attached to another
window
H_ERR_NVG_WM 5195 Invalid value of navigation mode
H_ERR_FINTERN 5196 Internal file error
H_ERR_FS 5197 Error while file synchronization
H_ERR_FISR 5198 Insufficient rights on file
H_ERR_BFD 5199 Bad file descriptor
H_ERR_FNF 5200 File not found
H_ERR_DWI 5201 Error while writing image data (sufficient memory?)
H_ERR_DWID 5202 Error while writing image descriptor (sufficient memory?)
H_ERR_DRI1 5203 Error while reading image data (format of image too small?)
H_ERR_DRI2 5204 Error while reading image data (format of image too big?)
H_ERR_DRID1 5205 Error while reading image descriptor: file too small
H_ERR_DIMMAT 5206 Image matrices are different
H_ERR_HNF 5207 Help file not found (setenv HALCONROOT <HALCON-
Homedirectory>)
120 HALCON Error Codes

Error Name Code Description

H_ERR_XNF 5208 Help index not found (setenv HALCONROOT <HALCON-

Homedirectory>)
H_ERR_CNCSI 5209 File <standard_input> can not be closed
H_ERR_CNCSO 5210 <standard_output/error> can not be closed
H_ERR_CNCF 5211 File can not be closed
H_ERR_EDWF 5212 Error while writing to file
H_ERR_NFA 5213 Exceeding of maximum number of files
H_ERR_WFIN 5214 Wrong file name
H_ERR_CNOF 5215 Error while opening the file
H_ERR_WFMO 5216 Wrong file mode
H_ERR_WPTY 5217 Wrong type for pixel (e.g. byte)
H_ERR_WIW 5218 Wrong image width (too big?)
H_ERR_WIH 5219 Wrong image height (too big?)
H_ERR_FTS1 5220 File already exhausted before reading an image
H_ERR_FTS2 5221 File exhausted before terminating the image
H_ERR_WDPI 5222 Wrong value for resolution (dpi)
H_ERR_WNOW 5223 Wrong output image size (width)
H_ERR_WNOH 5224 Wrong output image size (height)
H_ERR_WNFP 5225 Wrong number of parameter values: format description
H_ERR_WPNA 5226 Wrong parameter name for operator
H_ERR_WSNA 5227 Wrong slot name for parameter
H_ERR_NPCF 5228 Operator class is missing in help file
H_ERR_WHIF 5229 Wrong or inconsistent help/*.idx or help/*.sta
H_ERR_HINF 5230 File help/*.idx not found (setenv HALCONROOT
<HALCON-Homedirectory>)
H_ERR_HSNF 5231 File help/*.sta not found (setenv HALCONROOT
<HALCON-Homedirectory>)
H_ERR_ICSF 5232 Inconsistent file help/*.sta
H_ERR_EFNF 5233 No explication file (.exp) found
H_ERR_NFWKEF 5234 No file found in known graphic format
H_ERR_WIFT 5235 Wrong graphic format
H_ERR_ICNF 5236 Inconsistent file halcon.num
H_ERR_WTIFF 5237 File not a TIFF file
H_ERR_WFF 5238 Wrong file format
H_ERR_NOPNM 5242 No PNM format
H_ERR_ICODB 5243 Inconsistent or old help file ($HALCONROOT/help)
H_ERR_INVAL_FILE_ENC 5244 Invalid text file encoding
H_ERR_FNO 5245 File not open
H_ERR_NO_FILES 5246 No files in use so far (none opened)
H_ERR_NORFILE 5247 Invalid file format for regions
H_ERR_RDTB 5248 Error while reading region data: Format of region too big
H_ERR_BINFILE_ENC 5249 Setting the encoding is not supported for binary files
H_ERR_EDRF 5250 Error while reading from file
H_ERR_SNO 5251 Serial port not open
H_ERR_NSA 5252 No serial port available
H_ERR_CNOS 5253 Could not open serial port
H_ERR_CNCS 5254 Could not close serial port
H_ERR_CNGSA 5255 Could not get serial port attributes
H_ERR_CNSSA 5256 Could not set serial port attributes
H_ERR_WRSBR 5257 Wrong baud rate for serial connection
H_ERR_WRSDB 5258 Wrong number of data bits for serial connection
H_ERR_WRSFC 5259 Wrong flow control for serial connection
H_ERR_CNFS 5260 Could not flush serial port
H_ERR_EDWS 5261 Error during write to serial port
H_ERR_EDRS 5262 Error during read from serial port
H_ERR_REG_NOSITEM 5270 Serialized item does not contain valid regions
 121

Error Name Code Description

H_ERR_REG_WRVERS 5271 The version of the regions is not supported

H_ERR_IMG_NOSITEM 5272 Serialized item does not contain valid images
H_ERR_IMG_WRVERS 5273 The version of the images is not supported
H_ERR_XLD_NOSITEM 5274 Serialized item does not contain valid XLD objects
H_ERR_XLD_WRVERS 5275 The version of the XLD objects is not supported
H_ERR_OBJ_NOSITEM 5276 Serialized item does not contain valid objects
H_ERR_OBJ_WRVERS 5277 The version of the objects is not supported
H_ERR_OBJ_UNEXPECTED 5279 Unexpected object detected
H_ERR_FNOTF 5280 File has not been opened in text format
H_ERR_FNOBF 5281 File has not been opened in binary file format
H_ERR_DIRCR 5282 Cannot create directory
H_ERR_DIRRM 5283 Cannot remove directory
H_ERR_GETCWD 5284 Cannot determine current directory
H_ERR_SETCWD 5285 Cannot set current directory
H_ERR_XINIT 5286 Missing call to XInitThreads: multithreading support for X11
required
H_ERR_NFS 5300 No image acquisition device opened

Error Codes
H_ERR_FGWC 5301 Image acquisition: wrong color depth
H_ERR_FGWD 5302 Image acquisition: wrong device
H_ERR_FGVF 5303 Image acquisition: determination of video format not possible
H_ERR_FGNV 5304 Image acquisition: no video signal
H_ERR_UFG 5305 Unknown image acquisition device
H_ERR_FGF 5306 Image acquisition: failed grabbing of an image
H_ERR_FGWR 5307 Image acquisition: wrong resolution chosen
H_ERR_FGWP 5308 Image acquisition: wrong image part chosen
H_ERR_FGWPR 5309 Image acquisition: wrong pixel ratio chosen
H_ERR_FGWH 5310 Image acquisition: handle not valid
H_ERR_FGCL 5311 Image acquisition: instance not valid (already closed?)
H_ERR_FGNI 5312 Image acquisition: device cannot be initialized
H_ERR_FGET 5313 Image acquisition: external triggering not supported
H_ERR_FGLI 5314 Image acquisition: wrong camera input line (multiplex)
H_ERR_FGCS 5315 Image acquisition: wrong color space
H_ERR_FGPT 5316 Image acquisition: wrong port
H_ERR_FGCT 5317 Image acquisition: wrong camera type
H_ERR_FGTM 5318 Image acquisition: maximum number of acquisition device
classes exceeded
H_ERR_FGDV 5319 Image acquisition: device busy
H_ERR_FGASYNC 5320 Image acquisition: asynchronous grab not supported
H_ERR_FGPARAM 5321 Image acquisition: unsupported parameter
H_ERR_FGTIMEOUT 5322 Image acquisition: timeout
H_ERR_FGGAIN 5323 Image acquisition: invalid gain
H_ERR_FGFIELD 5324 Image acquisition: invalid field
H_ERR_FGPART 5325 Image acquisition: invalid parameter type
H_ERR_FGPARV 5326 Image acquisition: invalid parameter value
H_ERR_FGFNS 5327 Image acquisition: function not supported
H_ERR_FGIVERS 5328 Image acquisition: incompatible interface version
H_ERR_FGSETPAR 5329 Image acquisition: could not set parameter value
H_ERR_FGGETPAR 5330 Image acquisition: could not query parameter setting
H_ERR_FGPARNA 5331 Image acquisition: parameter not available in current
configuration
H_ERR_FGCLOSE 5332 Image acquisition: device could not be closed properly
H_ERR_FGCAMFILE 5333 Image acquisition: camera configuration file could not be
opened
H_ERR_FGCALLBACK 5334 Image acquisition: callback type not supported
H_ERR_FGDEVLOST 5335 Image acquisition: device lost
H_ERR_FGABORTED 5336 Image acquisition: aborted
H_ERR_IOTIMEOUT 5350 IO: timeout
122 HALCON Error Codes

Error Name Code Description

H_ERR_IOIVERS 5351 IO: incompatible interface version

H_ERR_IOWH 5352 IO: handle not valid
H_ERR_IODBUSY 5353 IO: device busy
H_ERR_IOIAR 5354 IO: insufficient user rights
H_ERR_IONF 5355 IO: device or channel not found
H_ERR_IOPART 5356 IO: invalid parameter type
H_ERR_IOPARV 5357 IO: invalid parameter value
H_ERR_IOPARNUM 5358 IO: invalid number of parameters
H_ERR_IOPARAM 5359 IO: unsupported parameter
H_ERR_IOPARNA 5360 IO: parameter not available in current configuration
H_ERR_IOFNS 5361 IO: function not supported
H_ERR_IOME 5362 IO: maximum number of IO devices or channels exceeded
H_ERR_IODNA 5363 IO: driver of IO device not available
H_ERR_IOABORTED 5364 IO: aborted
H_ERR_IODATT 5365 IO: invalid data type
H_ERR_IODEVLOST 5366 IO: device lost
H_ERR_IOSETPAR 5367 IO: could not set parameter value
H_ERR_IOGETPAR 5368 IO: could not query parameter value
H_ERR_IOCLOSE 5369 IO: device could not be closed properly
H_ERR_JXR_UNSUPPORTED_FORMAT 5400 Image type is not supported
H_ERR_JXR_INVALID_PIXEL_FORMAT 5401 Invalid pixel format
H_ERR_JXR_INTERNAL_ERROR 5402 Internal JPEG-XR error
H_ERR_JXR_FORMAT_SYNTAX_ERROR 5403 Invalid format string
H_ERR_JXR_TOO_MANY_CHANNELS 5404 Maximum number of channels exceeded
H_ERR_JXR_EC_ERROR 5405 Unspecified error in JPEG-XR library
H_ERR_JXR_EC_BADMAGIC 5406 Bad magic number in JPEG-XR library
H_ERR_JXR_EC_FEATURE_NOT_IMPLEMENTED 5407 Feature not implemented in JPEG-XR library
H_ERR_JXR_EC_IO 5408 File read/write error in JPEG-XR library
H_ERR_JXR_EC_BADFORMAT 5409 Invalid file format in JPEG-XR library
H_ERR_LIB_FILE_CLOSE 5500 Error while closing the image file
H_ERR_LIB_FILE_OPEN 5501 Error while opening the image file
H_ERR_LIB_UNEXPECTED_EOF 5502 Premature end of the image file
H_ERR_IDTL 5503 Image dimensions too large for this file format
H_ERR_ITLHV 5504 Image too large for this HALCON version
H_ERR_TMIO 5505 Too many iconic objects for this file format
H_ERR_FILE_FORMAT_UNSUPPORTED 5506 File format is unsupported
H_ERR_INCONSISTENT_DIMENSIONS 5507 All channels must have equal dimensions
H_ERR_PCX_NO_PCX_FILE 5510 File is no PCX-File
H_ERR_PCX_UNKNOWN_ENCODING 5511 PCX: unknown encoding
H_ERR_PCX_MORE_THAN_4_PLANES 5512 PCX: More than 4 image plains
H_ERR_PCX_COLORMAP_SIGNATURE 5513 PCX: Wrong magic in color table
H_ERR_PCX_REPEAT_COUNT_SPANS 5514 PCX: Wrong number of bytes in span
H_ERR_PCX_TOO_MUCH_BITS_PIXEL 5515 PCX: Wrong number of bits/pixels
H_ERR_PCX_PACKED_PIXELS 5516 PCX: Wrong number of plains
H_ERR_GIF_NO_GIF_PICTURE 5520 File is no GIF-File
H_ERR_GIF_BAD_VERSION 5521 GIF: Wrong version (not 87a/89a)
H_ERR_GIF_SCREEN_DESCRIPTOR 5522 GIF: Wrong descriptor
H_ERR_GIF_COLORMAP 5523 GIF: Wrong color table
H_ERR_GIF_READ_ERROR_EOF 5524 GIF: Premature end of file
H_ERR_GIF_NOT_ENOUGH_IMAGES 5525 GIF: Wrong number of images ’;’
H_ERR_GIF_ERROR_ON_EXTENSION 5526 GIF: Wrong image extension ’!’
H_ERR_GIF_LEFT_TOP_WIDTH 5527 GIF: Wrong left top width
H_ERR_GIF_CIRCULAR_TABL_ENTRY 5528 GIF: Cyclic index of table
H_ERR_GIF_BAD_IMAGE_DATA 5529 GIF: Wrong image data
H_ERR_SUN_RASTERFILE_TYPE 5530 File is no Sun-Raster-File
H_ERR_SUN_RASTERFILE_HEADER 5531 SUN-Raster: Wrong header
 123

Error Name Code Description

H_ERR_SUN_COLS 5532 SUN-Raster: Wrong image width

H_ERR_SUN_ROWS 5533 SUN-Raster: Wrong image height
H_ERR_SUN_COLORMAP 5534 SUN-Raster: Wrong color map
H_ERR_SUN_RASTERFILE_IMAGE 5535 SUN-Raster: Wrong image data
H_ERR_SUN_IMPOSSIBLE_DATA 5536 SUN-Raster: Wrong type of pixel
H_ERR_XWD_IMPOSSIBLE_DATA 5540 XWD: Wrong type of pixel
H_ERR_XWD_VISUAL_CLASS 5541 XWD: Wrong visual class
H_ERR_XWD_X10_HEADER 5542 XWD: Wrong X10 header
H_ERR_XWD_X11_HEADER 5543 XWD: Wrong X11 header
H_ERR_XWD_X10_COLORMAP 5544 XWD: Wrong X10 colormap
H_ERR_XWD_X11_COLORMAP 5545 XWD: Wrong X11 colormap
H_ERR_XWD_X11_PIXMAP 5546 XWD: Wrong pixmap
H_ERR_XWD_UNKNOWN_VERSION 5547 XWD: unknown version
H_ERR_XWD_READING_IMAGE 5548 XWD: Error while reading an image
H_ERR_TIF_BAD_INPUTDATA 5550 TIFF: Error while reading a file
H_ERR_TIF_COLORMAP 5551 TIFF: Wrong colormap
H_ERR_TIF_TOO_MANY_COLORS 5552 TIFF: Too many colors

Error Codes
H_ERR_TIF_BAD_PHOTOMETRIC 5553 TIFF: Wrong photometric interpretation
H_ERR_TIF_PHOTOMETRIC_DEPTH 5554 TIFF: Wrong photometric depth
H_ERR_TIF_NO_REGION 5555 TIFF: Image is no binary file
H_ERR_TIF_UNSUPPORTED_FORMAT 5556 TIFF: Image format not supported by HALCON
H_ERR_TIF_BAD_SPECIFICATION 5557 TIFF: Wrong specification of the TIFF file format
H_ERR_TIF_FILE_CORRUPT 5558 TIFF: TIFF file is corrupt
H_ERR_TIF_TAG_UNDEFINED 5559 TIFF: A required TIFF tag is missing in the TIFF file
H_ERR_BMP_NO_BMP_PICTURE 5560 File is no BMP-File
H_ERR_BMP_READ_ERROR_EOF 5561 BMP: Premature end of file
H_ERR_BMP_INCOMPLETE_HEADER 5562 BMP: Incomplete header
H_ERR_BMP_UNKNOWN_FORMAT 5563 BMP: Unknown bitmap format
H_ERR_BMP_UNKNOWN_COMPRESSION 5564 BMP: Unknown compression format
H_ERR_BMP_COLORMAP 5565 BMP: Wrong color table
H_ERR_BMP_WRITE_ERROR 5566 BMP: Write error on output
H_ERR_BMP_NO_REGION 5567 BMP: File does not contain a binary image
H_ERR_JPG_COMP_NUM 5570 JPEG: wrong number of components in image
H_ERR_JPGLIB_UNKNOWN 5571 JPEG: unknown error from libjpeg
H_ERR_JPGLIB_NOTIMPL 5572 JPEG: no implemented feature in libjpeg
H_ERR_JPGLIB_FILE 5573 JPEG: file access error in libjpeg
H_ERR_JPGLIB_TMPFILE 5574 JPEG: tmp file access error in libjpeg
H_ERR_JPGLIB_MEMORY 5575 JPEG: memory error in libjpeg
H_ERR_JPGLIB_INFORMAT 5576 JPEG: Error in input image
H_ERR_PNG_NO_PNG_FILE 5580 PNG: File is not a PNG file
H_ERR_PNG_UNKNOWN_INTERLACE_TYPE 5581 PNG: Unknown interlace type
H_ERR_PNG_UNSUPPORTED_COLOR_TYPE 5582 PNG: Unsupported color type
H_ERR_PNG_NO_REGION 5583 PNG: Image is no binary file
H_ERR_PNG_SIZE_TOO_BIG 5584 PNG: Maximal image size exceeded
H_ERR_TIF_TAG_ACCESS 5587 TIFF: Error accessing a TIFF tag
H_ERR_TIF_TAG_DATATYPE 5588 TIFF: Wrong datatype for specified TIFF tag
H_ERR_TIF_TAG_UNSUPPORTED 5589 TIFF: Requested TIFF tag not supported by HALCON
H_ERR_JP2_CORRUPT 5590 JPEG-2000: File corrupt
H_ERR_JP2_PREC_TOO_HIGH 5591 JPEG-2000: Image has more than 28 significant bits
H_ERR_JP2_ENCODING_ERROR 5592 JPEG-2000: Error while encoding
H_ERR_JP2_SIZE_TOO_BIG 5593 JPEG-2000: Maximal image size exceeded
H_ERR_JP2_INTERNAL_ERROR 5594 JPEG-2000: Could not initialize library
H_ERR_HOBJ_NOT_ONLY_IMAGES 5599 HOBJ: File does not contain only images
H_ERR_SOCKET_BLOCK 5600 Socket can not be set to block
H_ERR_SOCKET_UNBLOCK 5601 Socket can not be set to unblock
H_ERR_SOCKET_NO_CPAR 5602 Received data is no tuple
124 HALCON Error Codes

Error Name Code Description

H_ERR_SOCKET_NO_IMAGE 5603 Received data is no image

H_ERR_SOCKET_NO_RL 5604 Received data is no region
H_ERR_SOCKET_NO_XLD 5605 Received data is no xld object
H_ERR_SOCKET_READ_DATA_FAILED 5606 Error while reading from socket
H_ERR_SOCKET_WRITE_DATA_FAILED 5607 Error while writing to socket
H_ERR_SOCKET_WRONG_BYTE_NUMBER 5608 Illegal number of bytes with get_rl
H_ERR_SOCKET_BUFFER_OVERFLOW 5609 Buffer overflow in read_data
H_ERR_SOCKET_CANT_ASSIGN_FD 5610 Socket can not be created
H_ERR_SOCKET_CANT_BIND 5611 Bind on socket failed
H_ERR_SOCKET_CANT_GET_PORTNUMBER 5612 Socket information is not available
H_ERR_SOCKET_CANT_LISTEN 5613 Socket cannot listen for incoming connections
H_ERR_SOCKET_CANT_ACCEPT 5614 Connection could not be accepted
H_ERR_SOCKET_CANT_CONNECT 5615 Connection request failed
H_ERR_SOCKET_GETHOSTBYNAME 5616 Hostname could not be resolved
H_ERR_SOCKET_ILLEGAL_TUPLE_TYPE 5618 Unknown tuple type on socket
H_ERR_SOCKET_TIMEOUT 5619 Timeout occurred on socket
H_ERR_SOCKET_NA 5620 No more sockets available
H_ERR_SOCKET_NI 5621 Socket is not initialized
H_ERR_SOCKET_OOR 5622 Invalid socket
H_ERR_SOCKET_IS 5623 Socket is NULL
H_ERR_SOCKET_DATA_TOO_LARGE 5624 Received data type is too large
H_ERR_SOCKET_WRONG_TYPE 5625 Wrong socket protocol
H_ERR_SOCKET_NO_PACKED_DATA 5626 Received data does not contain packed data
H_ERR_SOCKET_PARAM_FAILED 5627 Error when handling the parameter
H_ERR_SOCKET_FORMAT_MISMATCH 5628 Format specification does not match the data
H_ERR_SOCKET_INVALID_FORMAT 5629 Invalid format specification
H_ERR_SOCKET_NO_SERIALIZED_ITEM 5630 Received data is no serialized item
H_ERR_SOCKET_TLS_CONTEXT 5631 Could not initialize TLS library
H_ERR_SOCKET_TLS_CERT_KEY 5632 Invalid TLS Certificate or private Key
H_ERR_SOCKET_TLS_HANDSHAKE 5633 TLS handshake failed
H_ERR_XLD_DATA_TOO_LARGE 5678 XLD object data can only be read by HALCON XL
H_ERR_ARCINFO_TOO_MANY_XLDS 5700 Too many contours/polygons for this file format
H_ERR_QUAT_WRONG_VERSION 5750 The version of the quaternion is not supported
H_ERR_QUAT_NOSITEM 5751 Serialized item does not contain a valid quaternion
H_ERR_HOM_MAT2D_WRONG_VERSION 5752 The version of the homogeneous matrix is not supported
H_ERR_HOM_MAT2D_NOSITEM 5753 Serialized item does not contain a valid homogeneous matrix
H_ERR_HOM_MAT3D_WRONG_VERSION 5754 The version of the homogeneous 3D matrix is not supported
H_ERR_HOM_MAT3D_NOSITEM 5755 Serialized item does not contain a valid homogeneous 3D
matrix
H_ERR_TUPLE_WRONG_VERSION 5756 The version of the tuple is not supported
H_ERR_TUPLE_NOSITEM 5757 Serialized item does not contain a valid tuple
H_ERR_TUPLE_DTLFTHV 5758 Number too big for a string to number conversion (overflow)
H_ERR_POSE_WRONG_VERSION 5759 The version of the camera parameters (pose) is not supported
H_ERR_POSE_NOSITEM 5760 Serialized item does not contain valid camera parameters
(pose)
H_ERR_CAM_PAR_WRONG_VERSION 5761 The version of the internal camera parameters is not supported
H_ERR_CAM_PAR_NOSITEM 5762 Serialized item does not contain valid internal camera
parameters
H_ERR_DUAL_QUAT_WRONG_VERSION 5763 The version of the dual quaternion is not supported
H_ERR_DUAL_QUAT_NOSITEM 5764 Serialized item does not contain a valid dual quaternion
H_ERR_NP 6000 Access to undefined memory area
H_ERR_MEM 6001 Not enough memory available
H_ERR_ICM 6002 Memory partition on heap has been overwritten
H_ERR_WMS 6003 HAlloc: 0 bytes requested
H_ERR_NOTMP 6004 Tmp-memory management: Call freeing memory although
nothing had been allocated
H_ERR_TMPNULL 6005 Tmp-memory management: Null pointer while freeing
 125

Error Name Code Description

H_ERR_CNFMEM 6006 Tmp-memory management: could not find memory element

H_ERR_WMT 6007 Memory management: wrong memory type allocated
H_ERR_MEM_VID 6021 Not enough video memory available
H_ERR_IAD 6040 System parameter for memory-allocation inconsistent
H_ERR_NRA 6041 No memory block allocated at last
H_ERR_INVALID_ALIGN 6042 Invalid alignment
H_ERR_NULL_PTR 6043 Function was given a NULL pointer as input
H_ERR_CP_FAILED 6500 Process creation failed
H_ERR_WOCPI 7000 Wrong index for output control parameter
H_ERR_WOCPVN 7001 Wrong number of values: output control parameter (see:
HPut*Par)
H_ERR_WOCPT 7002 Wrong type: output control parameter (see: HPut*Par)
H_ERR_WKT 7003 Wrong data type for object key (input objects)
H_ERR_IOOR 7004 Range for integer had been passed
H_ERR_IHV 7005 Inconsistent HALCON version
H_ERR_NISS 7006 Not enough memory for strings allocated
H_ERR_PROC_NULL 7007 Internal error: Proc is NULL

Error Codes
H_ERR_UNKN 7105 Unknown symbolic object key (input objects)
H_ERR_WOON 7200 Wrong number of output object parameter
H_ERR_OTSE 7400 System error: output type <string> expected
H_ERR_OTLE 7401 System error: output type <long> expected
H_ERR_OTFE 7402 System error: output type <float> expected
H_ERR_OPINP 7403 Object parameter is a zero pointer (’_’ not allowed)
H_ERR_TWC 7404 Tuple had been deleted; values are not valid any more
H_ERR_CNN_DATA 7701 CNN: Internal data error
H_ERR_CNN_MEM 7702 CNN: Invalid memory type
H_ERR_CNN_IO_INVALID 7703 CNN: Invalid data serialization
H_ERR_CNN_IMPL_NOT_AVAILABLE 7704 CNN: Implementation not available
H_ERR_CNN_NUM_INPUTS_INVALID 7705 Wrong number of input data
H_ERR_CNN_IMPL_INVALID 7706 CNN: Invalid implementation type selected
H_ERR_CNN_TRAINING_NOT_SUP 7707 CNN: Training is not supported by the current environment
H_ERR_CNN_GPU_REQUIRED 7708 For this operation a GPU with certain minimal hardware spec-
ifications is required (See installation guide)
H_ERR_CNN_CUDA_LIBS_MISSING 7709 For this operation a suitable GPU and the corresponding
CUDA libraries need to be available (See installation guide)
H_ERR_OCR_CNN_RE 7710 OCR File: Error while reading classifier
H_ERR_OCR_CNN_WGPN 7711 Wrong generic parameter name
H_ERR_OCR_CNN_EXCLUSIV_PARAM 7712 One of the generic parameters returns several values and has to
be used exclusively
H_ERR_CNN_WGPN 7713 Wrong generic parameter name
H_ERR_CNN_INVALID_LABELS 7714 Invalid label
H_ERR_OCR_CNN_FILE_WRONG_VERSION 7715 OCR File: Wrong file version
H_ERR_CNN_MULTIPLE_CLASSES 7716 Invalid classes: At least one class occurs twice
H_ERR_CNN_CUBLAS_LIBS_MISSING 7717 For this operation the cuBLAS library needs to be available
(See installation guide)
H_ERR_CNN_CUDNN_LIBS_MISSING 7718 For this operation the cuDNN library needs to be available (See
installation guide)
H_ERR_OCR_FNF_FIND_TEXT_SUPPORT 7719 File ’find_text_support.hotc’ not found. Please place this file
in the ocr subdirectory of the root directory of the HALCON
installation or in the current working directory
H_ERR_CNN_TRAINING_FAILED 7720 Training step failed. This might be caused by unsuitable
hyperparameters
H_ERR_CNN_NO_PRETRAINED_WEIGHTS 7721 Weights of the pretrained network have been overwritten and
cannot be restored
H_ERR_CNN_INVALID_INPUT_SIZE 7722 One or more input dimensions are too small for the network
H_ERR_CNN_RESULT_NOT_AVAILABLE 7723 The requested results are not available for this network
H_ERR_CNN_INVALID_INPUT_DEPTH 7724 The number of channels of the input image must be either 1 or
3
126 HALCON Error Codes

Error Name Code Description

H_ERR_CNN_DEPTH_NOT_AVAILABLE 7725 The number of channels of the input image cannot be set
H_ERR_CNN_INVALID_BATCH_SIZE 7726 Batch size smaller than subbatch size
H_ERR_CNN_INVALID_PARAM_SPEC 7727 Invalid parameter specification
H_ERR_CNN_EXCEEDS_MAX_MEM 7728 Internal memory management limit exceeded
H_ERR_CNN_BATCH_SIZE_OVERFLOW 7729 The required memory exceeds internal limits. This can be
caused by very high values of batch size
H_ERR_CNN_INVALID_IMAGE_SIZE 7730 The size of input image for the model is invalid. Width and
height must be divisible through the level of the last backbone
layer
H_ERR_CNN_INVALID_LAYER_PARAM_VALUE 7731 The parameter value is invalid for this graph node.
H_ERR_CNN_INVALID_LAYER_PARAM_NUM 7732 The number of parameters is invalid for this graph node.
H_ERR_CNN_INVALID_LAYER_PARAM_TYPE 7733 The parameter type is invalid for this graph node.
H_ERR_CNN_NUM_OUTPUTS_INVALID 7734 Wrong number of output data
H_ERR_CNN_INVALID_SHAPE 7735 CNN: Invalid shape of input
H_ERR_CNN_INVALID_INPUT_DATA 7736 CNN: Invalid input data
H_ERR_CNN_CUDNN_CTC_LOSS_BUGGY 7737 CNN: For variable input lengths the ctc loss layer only com-
putes correct gradients if the used cuDNN version is >= 7.6.3.
Please upgrade cuDNN or do not use variable input lengths.
H_ERR_CNN_INVALID_PADDING 7738 CNN: Invalid padding
H_ERR_CNN_IO_INVALID_LAYER_TYPE 7740 CNN: Invalid layer type serialization
H_ERR_CNN_INFERENCE_FAILED 7741 CNN: Inference failed. This might be caused by bad weights
created by unsuitable hyperparameters during the training
H_ERR_CNN_RUNTIME_FAILED 7742 CNN: Runtime unsupported on this machine
H_ERR_GRAPH_INTERNAL 7751 Graph: Internal error
H_ERR_GRAPH_IO_INVALID 7752 Graph: Invalid data serialization
H_ERR_GRAPH_INVALID_INDEX 7753 Graph: Invalid index
H_ERR_CNNGRAPH_INTERNAL 7760 CNN graph: Internal error
H_ERR_CNNGRAPH_IO_INVALID 7761 CNN graph: Invalid data serialization
H_ERR_CNNGRAPH_LAYER_INVALID 7762 CNN graph: Invalid layer specification
H_ERR_CNNGRAPH_NOINIT 7763 CNN graph: Graph not initialized properly
H_ERR_CNNGRAPH_INVALID_MEM 7764 CNN graph: Invalid memory type
H_ERR_CNNGRAPH_INVALID_NUML 7765 CNN graph: Invalid number of layers
H_ERR_CNNGRAPH_INVALID_IDX 7766 CNN graph: Invalid index
H_ERR_CNNGRAPH_SPEC_STATUS 7767 CNN graph: Invalid specification state
H_ERR_CNNGRAPH_NOCHANGE 7768 CNN graph: Graph is not allowed to be changed after
initialization
H_ERR_CNNGRAPH_PREPROC 7769 CNN graph: Missing preprocessing
H_ERR_CNNGRAPH_DEGREE 7770 CNN graph: Invalid vertex degree
H_ERR_CNNGRAPH_OUTSHAPE 7771 CNN graph: Invalid output shape
H_ERR_CNNGRAPH_SPEC 7772 CNN graph: Invalid specification
H_ERR_CNNGRAPH_DEF 7773 CNN graph: Invalid graph definition
H_ERR_CNNGRAPH_NO_CLASS_CHANGE 7774 CNN-Graph: Architecture not suitable for the adaption of the
number of output classes
H_ERR_CNNGRAPH_NO_IMAGE_RESIZE 7775 CNN-Graph: Architecture not suitable for the adaption of the
image size
H_ERR_CNNGRAPH_AUX_INDEX_OOB 7776 CNN-Graph: Auxiliary output index out of bounds.
H_ERR_CNNGRAPH_AUX_SPEC 7777 CNN-Graph: Invalid graph definition. Probably the auxiliary
outputs of a layer have not been connected with correspond-
ing aux selection layers (SelectAux) or at least one aux output
has not been specified during model creation (create_dl_model
call).
H_ERR_CNNGRAPH_LAYER_UNSUPPORTED 7778 CNN-Graph: At least one layer is unsupported for the selected
runtime or operation
H_ERR_DL_INTERNAL 7779 DL: Internal Error
H_ERR_DL_FILE_READ 7780 DL: Error while reading file
H_ERR_DL_FILE_WRITE 7781 DL: Error while writing file
H_ERR_DL_FILE_WRONG_VERSION 7782 DL: Wrong file version
H_ERR_DL_INPUTS_MISSING 7783 DL: Inputs missing in input dict
H_ERR_DL_INPUT_WRONG_BS 7784 DL: Inputs have incorrect batch size
 127

Error Name Code Description

H_ERR_DL_INVALID_NAME 7785 DL: Invalid layer name

H_ERR_DL_DUPLICATE_NAME 7786 DL: Duplicate layer name
H_ERR_DL_INVALID_OUTPUT 7787 DL: Invalid output layer
H_ERR_DL_PARAM_NOT_AVAILABLE 7788 DL: Parameter is not available for this model
H_ERR_DL_INPUT_WRONG_LENGTH 7789 DL: Tuple inputs have incorrect length
H_ERR_DL_INPUT_WRONG_TYPE 7790 DL: Tuple inputs have incorrect type
H_ERR_DL_INPUT_WRONG_VALUES 7791 DL: Some inputs have incorrect values
H_ERR_DL_CLASS_IDS_NOT_UNIQUE 7792 DL: Some class ids are not unique
H_ERR_DL_CLASS_IDS_INVALID 7793 DL: Some class ids have incorrect values.The expected value
range is [0, 65534]
H_ERR_DL_CLASS_IDS_INVALID_CONV 7794 DL: Input data of class id conversion is invalid
H_ERR_DL_TYPE_ALREADY_DEFINED 7795 DL: Type is already defined so it cannot be changed
H_ERR_DL_NO_INFERENCE_INPUTS 7796 DL: Cannot identify inference inputs
H_ERR_DL_CLASS_IDS_INVALID_OVERLAP 7797 DL: Class ids must not overlap with ignore class ids
H_ERR_DL_WRONG_OUTPUT_LAYER_NUM 7798 DL: Tuple of output layers has incorrect length
H_ERR_DL_WRONG_BS_MULTIPLIER 7799 DL: Batch size multiplier needs to be greater than 0
H_ERR_DL_INPUT_WRONG_BS_WITH_MULTIPLIER 7800 DL: Inputs have incorrect batch size. The number of needed
inputs is defined by batch_size * batch_size_multiplier

Error Codes
H_ERR_DL_READ_ONNX 7801 Error occurred while reading an ONNX model
H_ERR_DL_CLASS_IDS_MISSING 7802 DL: Model has no class ids
H_ERR_DL_WRITE_ONNX 7803 Error occurred while writing an ONNX model
H_ERR_DL_ONNX_LOADER 7804 Libprotobuf for ONNX could not be loaded
H_ERR_DL_FPN_SCALES 7810 DL: min_level or max_level not compatible with backbone
H_ERR_DL_FPN_INVALID_BACKBONE 7811 DL: Backbone unusable for FPN creation
H_ERR_DL_FPN_INVALID_FEATURE_MAP_SIZE 7812 DL: Image size not compatible with backbone
H_ERR_DL_FPN_INVALID_LEVELS 7813 DL: Invalid FPN-levels.
H_ERR_DL_ANCHOR 7820 DL: Internal error with anchors
H_ERR_DL_DETECTOR_INVALID_PARAM 7821 DL: Invalid detector parameter
H_ERR_DL_DETECTOR_INVALID_PARAM_VALUE 7822 DL: Invalid detector parameter value
H_ERR_DL_DETECTOR_INVALID_DOCKING_LAYER 7823 DL: Invalid backbone docking layer names
H_ERR_DL_DETECTOR_INVALID_INSTANCE_TYPE 7824 DL: Invalid instance type
H_ERR_DL_NODE_MISSING_PARAM_NAME 7830 DL-Node: Missing generic parameter ’name’. Please specify
a layer name.
H_ERR_DL_NODE_GENPARAM_NAME_NOT_ALLOWED 7831 DL-Node: No generic parameter ’name’ allowed for this node.
H_ERR_DL_NODE_INVALID_SPEC 7832 DL-Node: Invalid layer specification.
H_ERR_DL_NODE_DUPLICATE_EDGE 7833 DL-Node: There can only be one direct connection between
two layers.
H_ERR_DL_SOLVER_INVALID_TYPE 7840 DL: Invalid solver type.
H_ERR_DL_SOLVER_INVALID_UPDATE_FORMULA 7841 DL: Invalid solver update formula.
H_ERR_DL_HEATMAP_UNSUPPORTED_RUNTIME 7850 DL: The heatmap is unsupported with the selected runtime
H_ERR_DL_HEATMAP_UNSUPPORTED_MODEL_TYPE 7851 DL: The heatmap is not available for the selected model type
H_ERR_DL_HEATMAP_UNSUPPORTED_METHOD 7852 DL: The selected heatmap method is not supported
H_ERR_DL_HEATMAP_WRONG_TARGET_CLASS_ID 7853 DL: The selected target class is not available. Please choose a
valid class id.
H_ERR_DL_GCAD_NETWORK_NOT_AVAILABLE 7870 DL: GC anomaly detection model network is not available.
H_ERR_DL_ANOMALY_MODEL_INTERNAL 7880 DL: Anomaly detection model internal error.
H_ERR_DL_ANOMALY_MODEL_UNTRAINED 7881 DL: Anomaly detection model is not yet trained.
H_ERR_DL_ANOMALY_MODEL_TRAINING_FAILED 7882 DL: Training of anomaly detection model failed.
H_ERR_DL_ANOMALY_MODEL_PARAM_TRAINED 7883 DL: Unable to set parameter in a trained anomaly detection
model.
H_ERR_DL_ANOMALY_MODEL_RESIZE 7884 DL: Changing the model input size failed for the specified pa-
rameter value.
H_ERR_DL_ANOMALY_MODEL_DEPTH 7885 DL: Model input depth is not supported.
H_ERR_DL_ANOMALY_MODEL_INPUT_DOMAIN 7886 DL: The domain of the input image is empty.
H_ERR_DEEP_OCR_MODEL_INTERNAL 7890 Deep OCR internal error.
H_ERR_DEEP_OCR_MODEL_INVALID_ALPHABET 7891 Alphabet cannot contain items with a string length greater than
one.
128 HALCON Error Codes

Error Name Code Description

H_ERR_DEEP_OCR_MODEL_INVALID_ALPHABET_IDX 7892 Out of bounds indexing into alphabet.

H_ERR_DEEP_OCR_MODEL_INVALID_MODEL_TYPE 7893 The type of the given Deep OCR model component is not
allowed.
H_ERR_DEEP_OCR_MODEL_NOT_AVAILABLE 7894 The Deep OCR model component is not available.
H_ERR_DEEP_OCR_MODEL_INVALID_ALPHABET_MAPPING_NO_ALPHABET 7895 It is not possible to specify a mapping because there is no in-
ternal alphabet specified.
H_ERR_DEEP_OCR_MODEL_INVALID_ALPHABET_MAPPING_IDX 7896 Out of bounds index into internal alphabet given in mapping.
H_ERR_DEEP_OCR_MODEL_INVALID_ALPHABET_MAPPING_LEN 7897 The length of the mapping and the length of the internal alpha-
bet need to be the same.
H_ERR_DEEP_OCR_MODEL_FILE_NOT_FOUND 7898 The Deep OCR model file could not be found. Deep OCR
requires the installation of Deep Learning. Please make sure it
is installed correctly (see Installation Guide).
H_ERR_DEEP_OCR_MODEL_UNKNOWN_CHAR 7899 Some character is not part of the internal alphabet.
H_ERR_DEEP_OCR_MODEL_INVALID_WORD_LENGTH 7900 The given word length is invalid.
H_ERR_DEEP_OCR_MODEL_ALPHABET_NOT_UNIQUE 7901 The given alphabet is not a unique list of characters
H_ERR_DL_MODEL_APPLY_NO_DEF_OUTPUTS 7910 DL: The model architecture does not allow to specify default
outputs
H_ERR_DL_MODEL_UNSUPPORTED_GENPARAM 7911 DL: Unsupported generic parameter
H_ERR_DL_MODEL_OPERATOR_UNSUPPORTED 7912 DL: Operator does not support the model type
H_ERR_DL_MODEL_RUNTIME 7913 DL: Requested runtime cannot be set
H_ERR_DL_MODEL_UNSUPPORTED_GENVALUE 7914 DL: Unsupported generic parameter value
H_ERR_DL_MODEL_INVALID_NUM_SAMPLES 7915 DL: Invalid number of samples
H_ERR_DL_MODEL_CONVERTED_PARAM 7916 DL: Parameter unsupported for converted model
H_ERR_DL_MODEL_CONVERTED_UNSUPPORTED 7917 DL: Unsupported operation on converted model
H_ERR_DL_INVALID_DATASET 7925 DL: The given dataset is incorrect
H_ERR_DL_INVALID_SAMPLE_INDEX 7926 DL: Invalid sample index
H_ERR_DEEP_COUNTING_NOT_PREPARED 7940 The Deep Counting model is not prepared for applying on
images
H_ERR_DEEP_COUNTING_UNSUPPORTED_BACKBONE 7941 The type of the backbone for Deep Counting model must be of
the model type counting
H_ERR_DEEP_COUNTING_PREPARE_UNSUPPORTED 7942 The usage of preparing a Deep Counting model is not sup-
ported in this context
H_ERR_DEEP_COUNTING_NO_BACKBONE 7943 Deep Counting model has no backbone
H_ERR_DL_DEVICE_UNSUPPORTED_PRECISION 7960 DL: Unsupported device precision
H_ERR_DL_PRUNING_WRONG_DATA 7980 DL: Given pruning data and model are not compatible
H_ERR_DL_PRUNING_UNSUPPORTED_BY_CNN 7981 DL: The model architecture does not support pruning
H_ERR_DL_OOD_UNSUPPORTED_MODEL_TYPE 7985 DL: Invalid model type for out-of-distribution detection
H_ERR_DL_OOD_INSUFFICIENT_SAMPLE_DIVERSITY 7986 DL: Insufficient diverse samples for fitting out-of-distribution
detection
H_ERR_DL_OOD_INTERNAL_ERROR 7987 Internal error in the calculation of the out-of-distribution
detection
H_ERR_DL_OOD_INVALID 7988 Operation invalidates out-of-distribution detection.
H_ERR_DL_MODULE_NOT_LOADED 7990 DL: The DL module (libhalcondl.so/halcondl.dll) could not be
loaded
H_ERR_WPRN 8000 Unknown operator name
H_ERR_RCNA 8001 register_comp_used is not activated (see set_system)
H_ERR_WPC 8002 Unknown operator class
H_ERR_ORMF 8101 convol/mask: error while opening the file
H_ERR_EOFRMF 8102 convol/mask: premature end of file
H_ERR_CVTRMF 8103 convol/mask: conversion error
H_ERR_LCNRMF 8104 convol/mask: wrong row-/column number
H_ERR_WCOVRMF 8105 convol/mask: mask size overflow
H_ERR_NEOFRMF 8106 convol/mask: too many elements entered
H_ERR_WRRA 8107 convol: wrong margin type
H_ERR_MCN0 8108 convol: no mask object has got empty region
H_ERR_WF0 8110 convol: Weight factor is 0
H_ERR_NWC 8111 convol: inconsistent number of weights
H_ERR_WRRV 8112 rank: wrong rank value
 129

Error Name Code Description

H_ERR_ROVFL 8113 convol/rank: error while handling margin

H_ERR_EWPMF 8114 Error while parsing filter mask file
H_ERR_WNUMM 8120 Wrong number of coefficients for convolution (sigma too big?)
H_ERR_WBEDN 8200 No valid ID for data set
H_ERR_NBEDA 8201 No data set active (set_bg_esti)
H_ERR_BEDNAU 8202 ID already used for data set (is not possible)
H_ERR_NBEDC 8204 No data set created (create_bg_esti)
H_ERR_NTM 8205 Not possible to pass an object list
H_ERR_WISBE 8206 Image has other size than the background image in data set
H_ERR_UDNSSBE 8207 Up-date-region is bigger than background image
H_ERR_SNBETS 8208 Number of statistic data sets is too small
H_ERR_WAMBE 8209 Wrong value for adapt mode
H_ERR_WFMBE 8210 Wrong value for frame mode
H_ERR_PE_NPCTS 8250 Number of point correspondences too small
H_ERR_PE_INVMET 8251 Invalid pose estimation method
H_ERR_OCR_MEM1 8300 Maximum number of fonts exceeded
H_ERR_OCR_WID 8301 Wrong ID (Number) for font

Error Codes
H_ERR_OCR1 8302 OCR internal error: wrong ID
H_ERR_OCR_NNI 8303 OCR not initialized: no font was read in
H_ERR_OCR_NAI 8304 No font activated
H_ERR_OCR_WTP 8305 OCR internal error: wrong threshold in angle determination
H_ERR_OCR_WF 8306 OCR internal error: wrong attribute
H_ERR_OCR_READ 8307 The version of the OCR classifier is not supported
H_ERR_OCR_NODES 8308 OCR File: inconsistent number of nodes
H_ERR_OCR_EOF 8309 OCR File: File too short
H_ERR_OCR_INC1 8310 OCR: internal error 1
H_ERR_OCR_INC2 8311 OCR: internal error 2
H_ERR_WOCRTYPE 8312 Wrong type of OCR tool (no ’box’ or ’net’)
H_ERR_OCR_TRF 8313 The version of the OCR training characters is not supported
H_ERR_TRF_ITL 8314 Image too large for training file
H_ERR_TRF_RTL 8315 Region too large for training file
H_ERR_TRF_PT 8316 Protected training file
H_ERR_TRF_WPW 8317 Wrong password for protected training file
H_ERR_OCR_NOSITEM 8318 Serialized item does not contain a valid OCR classifier
H_ERR_TRF_CON_EIO 8319 OCR training file concatenation failed: identical input and out-
put files
H_ERR_OCR_MLP_NOCLASSFILE 8320 Invalid file format for MLP classifier
H_ERR_OCR_MLP_WRCLASSVERS 8321 The version of the MLP classifier is not supported
H_ERR_OCR_MLP_NOSITEM 8322 Serialized item does not contain a valid MLP classifier
H_ERR_OCR_SVM_NOCLASSFILE 8330 Invalid file format for SVM classifier
H_ERR_OCR_SVM_WRCLASSVERS 8331 The version of the SVM classifier is not supported
H_ERR_OCR_SVM_NOSITEM 8332 Serialized item does not contain a valid SVM classifier
H_ERR_OCR_KNN_NOCLASSFILE 8333 Invalid file format for k-NN classifier
H_ERR_OCR_KNN_NOSITEM 8334 Serialized item does not contain a valid k-NN classifier
H_ERR_OCR_CNN_NOCLASSFILE 8335 Invalid file format for CNN classifier
H_ERR_OCR_CNN_WRCLASSVERS 8336 The version of the CNN classifier is not supported
H_ERR_OCR_CNN_NOSITEM 8337 Serialized item does not contain a valid CNN classifier
H_ERR_OCR_RESULT_NOT_AVAILABLE 8338 The result is not available for the selected text segmentation
method
H_ERR_OCV_NI 8350 OCV system not initialized
H_ERR_WOCVTYPE 8351 The version of the OCV tool is not supported
H_ERR_OCV_WNAME 8353 Wrong name for an OCV object
H_ERR_OCV_II 8354 Training has already been applied
H_ERR_OCV_NOTTR 8355 No training has been applied to the character
H_ERR_OCV_NOSITEM 8356 Serialized item does not contain a valid OCV tool
H_ERR_WLENGTH 8370 Wrong number of function points
130 HALCON Error Codes

Error Name Code Description

H_ERR_NO_FUNCTION 8371 List of values is not a function

H_ERR_NOT_ASCENDING 8372 Wrong ordering of values (not ascending)
H_ERR_ILLEGAL_DIST 8373 Illegal distance of function points
H_ERR_NOT_MONOTONIC 8374 Function is not monotonic
H_ERR_WFUNCTION 8375 Wrong function type
H_ERR_SAME_XVAL_CONV 8376 The function contains multiple points with different x-values,
that match the same value after the conversion from double to
float.
H_ERR_GRID_CONNECT_POINTS 8390 The input points could not be arranged in a regular grid
H_ERR_GRID_GEN_MAP 8391 Error while creating the output map
H_ERR_GRID_AUTO_ROT 8392 Auto rotation failed
H_ERR_CAL_NO_COMM_PAR 8393 No common camera parameters
H_ERR_CAL_NEGVY 8394 Vy must be > 0
H_ERR_CAL_IDENTICAL_FP 8395 Same finder pattern found multiple times
H_ERR_CAL_LSCPNA 8396 Function not available for line scan cameras with perspective
lenses
H_ERR_CAL_MARK_SEGM 8397 Segmentation of the calibration marks failed
H_ERR_CAL_CONT_EXT 8398 Extraction of the mark contours failed
H_ERR_CAL_NO_FP 8399 No finder pattern could be found
H_ERR_CAL_LCALP 8400 You have to indicate at least 3 calibration points
H_ERR_CAL_INCONSISTENT_FP 8401 Inconsistent finder pattern positions (image mirrored?)
H_ERR_CAL_NCPF 8402 No calibration table found
H_ERR_CAL_RECPF 8403 Error while reading calibration table description file
H_ERR_CAL_LTMTH 8404 Minimum threshold while searching for ellipses
H_ERR_CAL_FRCP 8405 Read error / format error in calibration table description file
H_ERR_CAL_PROJ 8406 Point cannot be projected
H_ERR_CAL_UNPRO 8407 Error in inverse projection
H_ERR_CAL_RICPF 8408 Not possible to open camera parameter file
H_ERR_CAL_FICP1 8409 Format error in file: no colon
H_ERR_CAL_FICP2 8410 Format error in file: 2. colon is missing
H_ERR_CAL_FICP3 8411 Format error in file: semicolon is missing
H_ERR_CAL_REPOS 8412 Not possible to open camera parameter (pose) file
H_ERR_CAL_FOPOS 8413 Format error in camera parameter (pose) file
H_ERR_CAL_OCPDF 8414 Not possible to open calibration target description file
H_ERR_CAL_OCPPS 8415 Not possible to open postscript file of calibration target
H_ERR_CAL_EVECN 8416 Error while normalizing the vector
H_ERR_CAL_NPLAN 8417 Fitting of calibration target failed
H_ERR_CAL_NNMAR 8418 No next mark found
H_ERR_CAL_NNEQU 8419 Normal equation system is not solvable
H_ERR_CAL_QETHM 8420 Average quadratic error is too big for 3D position of mark
H_ERR_CAL_NOELL 8421 Non elliptic contour
H_ERR_CAL_WPARV 8422 Wrong parameter value slvand()
H_ERR_CAL_WFRES 8423 Wrong function results slvand()
H_ERR_CAL_ECPDI 8424 Distance of marks in calibration target description file is not
possible
H_ERR_CAL_WEFLA 8425 Specified flag for degree of freedom not valid
H_ERR_CAL_NOMER 8426 Minimum error did not fall below
H_ERR_CAL_WPTYP 8427 Wrong type in Pose (rotation / translation)
H_ERR_CAL_WIMSZ 8428 Image size does not match the measurement in camera
parameters
H_ERR_CAL_NPILS 8429 Point could not be projected into linescan image
H_ERR_CAL_DIACM 8430 Diameter of calibration marks could not be determined
H_ERR_CAL_ORICP 8431 Orientation of calibration plate could not be determined
H_ERR_CAL_CPNII 8432 Calibration plate does not lie completely inside the image
H_ERR_CAL_WNCME 8433 Wrong number of calibration marks extracted
H_ERR_CAL_UNKPG 8434 Unknown name of parameter group
H_ERR_CAL_NEGFL 8435 Focal length must be non-negative
 131

Error Name Code Description

H_ERR_CAL_TELNA 8436 Function not available for cameras with telecentric lenses
H_ERR_CAL_LSCNA 8437 Function not available for line scan cameras
H_ERR_CAL_ELLDP 8438 Ellipse is degenerated to a point
H_ERR_CAL_NOMF 8439 No orientation mark found
H_ERR_CAL_NCONV 8440 Camera calibration did not converge
H_ERR_CAL_HYPNA 8441 Function not available for cameras with hypercentric lenses
H_ERR_CAL_DISTORT 8442 Point cannot be distorted
H_ERR_CAL_WREDGFILT 8443 Wrong edge filter for the mark extraction
H_ERR_CAL_NEGPS 8444 Pixel size must be positive
H_ERR_CAL_NEGTS 8445 Tilt must be within the range of 0° and 90°
H_ERR_CAL_NEGRS 8446 Rot must be within the range of 0° and 360°
H_ERR_CAL_INVCAMPAR 8447 Invalid camera parameters
H_ERR_CAL_ILLFL 8448 Focal length must be positive
H_ERR_CAL_ILLMAG 8449 Magnification must be positive
H_ERR_CAL_ILLIPD 8450 Illegal image plane distance
H_ERR_CM_NOT_OPTIMIZED 8451 Model not optimized yet - no results can be queried
H_ERR_CM_NOT_POSTPROCC 8452 Model not postprocessed yet - no auxiliary results can be

Error Codes
queried
H_ERR_CM_NOT_INTERCONN 8453 Calibration setup: fields of view do not intersect
H_ERR_CM_CAMPAR_MISMCH 8454 Camera type and camera parameters incompatible
H_ERR_CM_CAMTYP_MISMCH 8455 Calibration setup: incompatible camera types
H_ERR_CM_CAMTYP_UNSUPD 8456 Camera type not supported
H_ERR_CM_INVALD_CAMIDX 8457 Invalid camera index
H_ERR_CM_INVALD_DESCID 8458 Invalid calibration object index
H_ERR_CM_INVALD_COBJID 8459 Invalid calibration object pose index
H_ERR_CM_UNDEFINED_CAM 8460 Undefined camera
H_ERR_CM_REPEATD_INDEX 8461 Indices: ambiguous observation index
H_ERR_CM_UNDEFI_CADESC 8462 Undefined calibration object
H_ERR_CM_NO_DESCR_FILE 8463 Invalid file format for calibration data model
H_ERR_CM_WR_DESCR_VERS 8464 The version of the calibration data model is not supported
H_ERR_CM_ZERO_MOTION 8465 Zero-motion in line scan camera parameters
H_ERR_CM_MULTICAM_UNSP 8466 Calibration setup: multiple cameras and/or calibration objects
not supported for camera type
H_ERR_CM_INCMPLTE_DATA 8467 Incomplete observation data
H_ERR_CSM_NO_DESCR_FIL 8468 Invalid file format for camera setup model
H_ERR_CSM_WR_DESCR_VER 8469 The version of the camera setup model is not supported
H_ERR_CM_CALTAB_NOT_AV 8470 Full HALCON calibration plate description required
H_ERR_CM_INVAL_OBSERID 8471 Invalid observation index
H_ERR_CSM_NOSITEM 8472 Serialized item does not contain a valid camera setup model
H_ERR_CM_NOSITEM 8473 Serialized item does not contain a valid calibration data model
H_ERR_CM_INV_TOOLPOSID 8474 Invalid tool pose index
H_ERR_CM_UNDEFINED_TOO 8475 Undefined tool pose
H_ERR_CM_INVLD_MODL_TY 8476 Feature or operation not supported for current calibration data
model type
H_ERR_CSM_UNINIT_CAM 8477 The camera setup model contains an uninitialized camera
H_ERR_CM_NO_VALID_SOL 8478 The hand-eye algorithm failed to find a valid solution
H_ERR_CM_INVAL_OBS_POSE 8479 Invalid observation pose: set_calib_data_observ_pose can
only be called with calibration data models that have been con-
figured for hand-eye-calibration; please use find_calib_object
or set_calib_data_observ_points
H_ERR_CM_TOO_FEW_POSES 8480 Not enough calibration object poses: For the hand-eye-
calibration at least three calibration object poses are necessary
H_ERR_CM_UNDEF_CAM_TYP 8481 Undefined camera type
H_ERR_SM_INVLD_IMG_PAIRS_DISP_VAL 8482 Number of image pairs does not correspond to the number of
disparity values
H_ERR_SM_INVLD_DISP_VAL 8483 Wrong value of stereo model parameter ’min_disparity’ or
’max_disparity’
H_ERR_SM_NO_IM_PAIR 8484 No camera pair set by set_stereo_model_image_pairs
132 HALCON Error Codes

Error Name Code Description

H_ERR_SM_NO_VIS_COLOR 8485 No reconstructed point is visible for coloring

H_ERR_SM_NO_RECONSTRUCT 8486 No camera pair yields reconstructed points (please check pa-
rameters of disparity method or bounding box)
H_ERR_SM_INVLD_BB_PARTITION 8487 Partitioning of bounding box is too fine (please adapt the pa-
rameter ’resolution’ or the bounding box)
H_ERR_SM_INVLD_DISP_RANGE 8488 Disparity range as calculated by the bounding box and
the parameter ’rectif_sub_sampling’ exceeds the maximum
permitted
H_ERR_SM_INVLD_BIN_PAR 8489 The parameter to be set is not supported by the chosen disparity
method
H_ERR_SM_INVLD_MODL_TY 8490 Feature or operation not supported for current stereo model
type
H_ERR_SM_NOT_PERSISTEN 8491 Feature or operation available only in ’persistent’ mode
H_ERR_SM_INVLD_BOU_BOX 8492 Invalid bounding box
H_ERR_SR_INVLD_IMG_SIZ 8493 Image sizes must be identical with the corresponding camera
parameters from the camera setup
H_ERR_SR_BBOX_BHND_CAM 8494 Bounding box lies partially or completely behind (for hyper-
centric lenses: in front of) the base line of at least one camera
pair
H_ERR_CAL_AMBIGUOUS 8495 Ambiguous calibration: Please, recalibrate with improved in-
put data!
H_ERR_CAL_PCPND 8496 Pose of calibration plate could not be determined!
H_ERR_CAL_FAILED 8497 Calibration failed: Please check your input data and calibrate
again!
H_ERR_CAL_MISSING_DATA 8498 No observation data supplied!
H_ERR_CAL_FEWER_FOUR 8499 The calibration object has to be seen at least once by every
camera, if less than four cameras are used
H_ERR_NOAP 8500 Invalid file format for template
H_ERR_WPFV 8501 The version of the template is not supported
H_ERR_MATCH_MODE 8502 Error during changing the file mode (t/b)
H_ERR_MATCH_OOR 8503 Inconsistent match file: coordinates out of range
H_ERR_NOTAP 8505 The image(s) is not a pyramid (wrong zooming factor?)
H_ERR_NGTPTS 8506 Number of template points too small
H_ERR_PDTL 8507 Template data can only be read by HALCON XL
H_ERR_NCC_NOSITEM 8508 Serialized item does not contain a valid NCC model
H_ERR_MATCH_NOSITEM 8509 Serialized item does not contain a valid template
H_ERR_NTPTS 8510 Number of shape model points too small
H_ERR_CGSMM 8511 Gray-value-based and color-based shape models cannot be
searched simultaneously
H_ERR_SMTL 8512 Shape model data can only be read by HALCON XL
H_ERR_SMNXLD 8513 Shape model was not created from XLDs
H_ERR_SM_NOSITEM 8514 Serialized item does not contain a valid shape model
H_ERR_SM_CL_CONT 8515 Shape model contour too near to clutter region
H_ERR_SM_NO_CLUT 8516 Shape model does not contain clutter parameters
H_ERR_SM_SAME_CL 8517 Activation status for the usage of clutter parameters is not iden-
tical for all shape models
H_ERR_SM_WRONG_CLCO 8518 Shape model has an invalid clutter contrast
H_ERR_SM_CL_NEG 8519 Clutter region contains negative coordinates
H_ERR_FIND_BOX_UNSUP_GENPARAM 8520 Box Finder: Unsupported generic parameter
H_ERR_COMP_DRT 8530 Initial components have different region types
H_ERR_COMP_SAMF 8531 Solution of ambiguous matches failed
H_ERR_IGF_NC 8532 Computation of the incomplete gamma function not converged
H_ERR_MSA_TMN 8533 Too many nodes while computing the minimum spanning
arborescence
H_ERR_CTTL 8534 Component training data can only be read by HALCON XL
H_ERR_CMTL 8535 Component model data can only be read by HALCON XL
H_ERR_COMP_NOSITEM 8536 Serialized item does not contain a valid component model
H_ERR_TRAIN_COMP_NOSITEM 8537 Serialized item does not contain a valid component training
result
 133

Error Name Code Description

H_ERR_VARIATION_WS 8540 Size of the training image and the variation model differ
H_ERR_VARIATION_PREP 8541 Variation model has not been prepared for segmentation
H_ERR_VARIATION_WRMD 8542 Invalid variation model training mode
H_ERR_VARIATION_NOVF 8543 Invalid file format for variation model
H_ERR_VARIATION_WVFV 8544 The version of the variation model is not supported
H_ERR_VARIATION_TRDC 8545 Training data has already been cleared
H_ERR_VARIATION_NOSITEM 8546 Serialized item does not contain a valid variation model
H_ERR_MEASURE_NA 8550 No more measure objects available
H_ERR_MEASURE_NI 8551 Measure object is not initialized
H_ERR_MEASURE_OOR 8552 Invalid measure object
H_ERR_MEASURE_IS 8553 Measure object is NULL
H_ERR_MEASURE_WS 8554 Measure object has wrong image size
H_ERR_MEASURE_NO_MODEL_FILE 8555 Invalid file format for measure object
H_ERR_MEASURE_WRONG_VERSION 8556 The version of the measure object is not supported
H_ERR_MEASURE_TL 8557 Measure object data can only be read by HALCON XL
H_ERR_MEASURE_NOSITEM 8558 Serialized item does not contain a valid measure object
H_ERR_METROLOGY_MODEL_NI 8570 Metrology model is not initialized

Error Codes
H_ERR_METROLOGY_OBJECT_INVALID 8572 Invalid metrology object
H_ERR_METROLOGY_FIT_NOT_ENOUGH_MEASURES 8573 Not enough valid measures for fitting the metrology object
H_ERR_METROLOGY_NO_MODEL_FILE 8575 Invalid file format for metrology model
H_ERR_METROLOGY_WRONG_VERSION 8576 The version of the metrology model is not supported
H_ERR_METROLOGY_NO_FUZZY_FUNC 8577 Fuzzy function is not set
H_ERR_METROLOGY_NOSITEM 8578 Serialized item does not contain a valid metrology model
H_ERR_METROLOGY_UNDEF_CAMPAR 8579 Camera parameters are not set
H_ERR_METROLOGY_UNDEF_POSE 8580 Pose of the measurement plane is not set
H_ERR_METROLOGY_SET_MODE 8581 Mode of metrology model cannot be set since an object has
already been added
H_ERR_METROLOGY_OP_NOT_ALLOWED 8582 If the pose of the metrology object has been set several times,
the operator is not longer allowed
H_ERR_METROLOGY_MULTI_POSE_CAM_PAR 8583 All objects of a metrology model must have the same world
pose and camera parameters
H_ERR_METROLOGY_WRONG_INPUT_MODE 8584 The input type does not correspond to the input type set for the
metrology model
H_ERR_DLOPEN 8600 Dynamic library could not be opened
H_ERR_DLCLOSE 8601 Dynamic library could not be closed
H_ERR_DLLOOKUP 8602 Symbol not found in dynamic library
H_ERR_COMPONENT_NOT_INSTALLED 8603 Interface library not available. Check
www.mvtec.com/download for additional interfaces
H_ERR_EAD_CAL_NII 8650 Not enough information for radiometric calibration
H_ERR_WGSMFV 8670 The version of the shape model result is not supported
H_ERR_GSM_INVALID_RES_SCALE 8671 Restrict scale parameter outside the trained range
H_ERR_GSM_INVALID_ANGLE 8672 Angle parameter outside the trained range
H_ERR_GSM_NEEDS_TRAINING 8673 Shape model needs training
H_ERR_GSM_CONTRAST_HYS 8674 contrast_high cannot be smaller than contrast_low
H_ERR_GSM_CONTRAST_MIN_CONTRAST 8675 Neither contrast_low nor contrast_high can be smaller than
min_contrast
H_ERR_GSM_ISO_SCALE_PAIR 8676 iso_scale_max cannot be smaller than iso_scale_min
H_ERR_GSM_ANISO_SCALE_ROW 8677 scale_row_max cannot be smaller than scale_row_min
H_ERR_GSM_ANISO_SCALE_COLUMN 8678 scale_column_max cannot be smaller than scale_column_min
H_ERR_GSM_ISO_NOT_SET 8679 Isotropic scaling not set
H_ERR_GSM_ANISO_NOT_SET 8680 Anisotropic scaling not set
H_ERR_GSM_INVALID_METRIC_XLD 8681 No edge direction available to change shape matching metric
H_ERR_GSM_SAME_IDENTIFIER 8682 Shape models with the same identifier cannot be searched
simultaneously
H_ERR_SM_INCONSISTENT_PER_LEVEL 8683 Set parameters are inconsistent with estimated ’per_level’
values
H_ERR_GSM_EXT_PAR_EST 8684 Extended parameter estimation failed for the shape model
134 HALCON Error Codes

Error Name Code Description

H_ERR_BAR_WNOM 8701 Wrong number of modules

H_ERR_BAR_WNOE 8702 Wrong number of elements
H_ERR_BAR_UNCHAR 8703 Unknown character (for this code)
H_ERR_BAR_WRONGDESCR 8705 Wrong name for attribute in barcode descriptor
H_ERR_BAR_EL_LENGTH 8706 Wrong thickness of element
H_ERR_BAR_NO_REG 8707 No region found
H_ERR_BAR_WRONGCODE 8708 Wrong type of bar code
H_ERR_BAR_INTERNAL 8709 Internal error in bar code reader
H_ERR_BAR_NO_DECODED_SCANLINE 8710 Bar code candidate does not contain a decoded scanline
H_ERR_BC_EMPTY_MODEL_LIST 8721 List of bar code models is empty
H_ERR_BC_TRAIN_ONLY_SINGLE 8722 Training cannot be done for multiple bar code types
H_ERR_BC_GET_SPECIFIC 8723 Cannot get bar code type specific parameter with
get_bar_code_param. Use get_bar_code_param_specific
H_ERR_BC_GET_OBJ_MULTI 8724 Cannot get this object for multiple bar code types. Try again
with single bar code type
H_ERR_BC_WR_FILE_FORMAT 8725 Invalid file format for bar code model
H_ERR_BC_WR_FILE_VERS 8726 The version of the bar code model is not supported
H_ERR_BC_NOT_PERSISTANT 8727 Feature or operation available only in ’persistent’ mode
H_ERR_BC_GRAY_OUT_OF_RANGE 8728 Incorrect index of scanline’s gray values
H_ERR_NO_PERSISTENT_OP_CALL 8729 Neither find_bar_code nor decode_bar_code_rectanlge2 have
been called in persistent mode on this model
H_ERR_BC_ZOOMED_ABORTED 8730 The zoomed barcode algorithm has been aborted
H_ERR_BC_ZOOMED_INVALID_INPUT 8731 zoomed barcode: Invalid input data.
H_ERR_BC_XCORR_INVALID_INPUT 8740 Barcode: Invalid inputs for NCC
H_ERR_BC_XCORR_TOO_MANY_BAD_ROWS 8741 Barcode: Too many invalid rows during NCC
H_ERR_BC_XCORR_NO_CORRELATION 8742 Barcode: No correlation found during NCC
H_ERR_INVALID_SYNTAX_DICTIONARY 8743 Invalid GS1 Application Identifier Syntax Dictionary
H_ERR_BAR2D_UNKNOWN_TYPE 8800 Specified code type is not supported
H_ERR_BAR2D_WRONG_FOREGROUND 8801 Wrong foreground specified
H_ERR_BAR2D_WRONG_SIZE 8802 Wrong matrix size specified
H_ERR_BAR2D_WRONG_SHAPE 8803 Wrong symbol shape specified
H_ERR_BAR2D_WRONG_PARAM_NAME 8804 Wrong generic parameter name
H_ERR_BAR2D_WRONG_PARAM_VAL 8805 Wrong generic parameter value
H_ERR_BAR2D_WRONG_MODE 8806 Wrong symbol printing mode
H_ERR_BAR2D_SYMBOL_ON_BORDER 8807 Symbol region too near to image border
H_ERR_BAR2D_MODULE_CONT_NUM 8808 No rectangular modul boundaries found
H_ERR_BAR2D_SYMBOL_FINDER 8809 Couldn’t identify symbol finder
H_ERR_BAR2D_SYMBOL_DIMENSION 8810 Symbol region with wrong dimension
H_ERR_BAR2D_CLASSIF_FAILED 8811 Classification failed
H_ERR_BAR2D_DECODING_FAILED 8812 Decoding failed
H_ERR_BAR2D_DECODING_READER 8813 Reader programming not supported
H_ERR_DC2D_GENERAL 8820 General 2d data code error
H_ERR_DC2D_BROKEN_SIGN 8821 Corrupt signature of 2d data code handle
H_ERR_DC2D_INVALID_HANDLE 8822 Invalid 2d data code handle
H_ERR_DC2D_EMPTY_MODEL_LIST 8823 List of 2d data code models is empty
H_ERR_DC2D_NOT_INITIALIZED 8824 Access to uninitialized (or not persistent) internal data
H_ERR_DC2D_INVALID_CANDIDATE 8825 Invalid ’Candidate’ parameter
H_ERR_DC2D_INDEX_PARNUM 8826 It’s not possible to return more than one parameter for several
candidates
H_ERR_DC2D_EXCLUSIV_PARAM 8827 One of the parameters returns several values and has to be used
exclusively for a single candidate
H_ERR_DC2D_DEF_SET_NOT_FIRST 8828 Parameter for default settings must be the first in the parameter
list
H_ERR_DC2D_INTERNAL_UNEXPECTED 8829 Unexpected 2d data code error
H_ERR_DC2D_WRONG_PARAM_VALUE 8830 Invalid parameter value
H_ERR_DC2D_WRONG_PARAM_NAME 8831 Unknown parameter name
H_ERR_DC2D_WRONG_POLARITY 8832 Invalid value for ’polarity’
 135

Error Name Code Description

H_ERR_DC2D_WRONG_SYMBOL_SHAPE 8833 Invalid value for ’symbol_shape’

H_ERR_DC2D_WRONG_SYMBOL_SIZE 8834 Invalid symbol size
H_ERR_DC2D_WRONG_MODULE_SIZE 8835 Invalid module size
H_ERR_DC2D_WRONG_MODULE_SHAPE 8836 Invalid value for ’module_shape’
H_ERR_DC2D_WRONG_ORIENTATION 8837 Invalid value for ’orientation’
H_ERR_DC2D_WRONG_CONTRAST 8838 Invalid value for ’contrast_min’
H_ERR_DC2D_WRONG_MEAS_THRESH 8839 Invalid value for ’measure_thresh’
H_ERR_DC2D_WRONG_ALT_MEAS_RED 8840 Invalid value for ’alt_measure_red’
H_ERR_DC2D_WRONG_SLANT 8841 Invalid value for ’slant_max’
H_ERR_DC2D_WRONG_L_DIST 8842 Invalid value for ’L_dist_max’
H_ERR_DC2D_WRONG_L_LENGTH 8843 Invalid value for ’L_length_min’
H_ERR_DC2D_WRONG_GAP 8844 Invalid module gap
H_ERR_DC2D_WRONG_DEF_SET 8845 Invalid value for ’default_parameters’
H_ERR_DC2D_WRONG_TEXTURED 8846 Invalid value for ’back_texture’
H_ERR_DC2D_WRONG_MIRRORED 8847 Invalid value for ’mirrored’
H_ERR_DC2D_WRONG_CLASSIFICATOR 8848 Invalid value for ’classificator’
H_ERR_DC2D_WRONG_PERSISTENCE 8849 Invalid value for ’persistence’

Error Codes
H_ERR_DC2D_WRONG_MODEL_TYPE 8850 Invalid model type
H_ERR_DC2D_WRONG_MOD_ROI_PART 8851 Invalid value for ’module_roi_part’
H_ERR_DC2D_WRONG_FP_TOLERANCE 8852 Invalid value for ’finder_pattern_tolerance’
H_ERR_DC2D_WRONG_MOD_ASPECT 8853 Invalid value for ’mod_aspect_max’
H_ERR_DC2D_WRONG_SM_ROBUSTNESS 8854 Invalid value for ’small_modules_robustness’
H_ERR_DC2D_WRONG_CONTRAST_TOL 8855 Invalid ’contrast_tolerance’
H_ERR_DC2D_WRONG_AP_TOLERANCE 8856 Invalid value for ’alternating_pattern_tolerance’
H_ERR_DC2D_READ_HEAD_FORMAT 8860 Invalid header in 2d data code model file
H_ERR_DC2D_READ_HEAD_SIGN 8861 Invalid code signature in 2d data code model file
H_ERR_DC2D_READ_LINE_FORMAT 8862 Corrupted line in 2d data code model file
H_ERR_DC2D_WRONG_MODULE_ASPECT 8863 Invalid module aspect ratio
H_ERR_DC2D_WRONG_LAYER_NUM 8864 Invalid layer num
H_ERR_DCD_READ_WRONG_VERSION 8865 Wrong data code model file version
H_ERR_DC2D_NOSITEM 8866 Serialized item does not contain a valid 2D data code model
H_ERR_DC2D_WR_FILE_FORMAT 8867 Invalid file format for data code model
H_ERR_SM3D_WRONG_PARAM_NAME 8900 Unknown parameter name
H_ERR_SM3D_WRONG_NUM_LEVELS 8901 Invalid value for ’num_levels’
H_ERR_SM3D_WRONG_OPTIMIZATION 8902 Invalid value for ’optimization’
H_ERR_SM3D_WRONG_METRIC 8903 Invalid value for ’metric’
H_ERR_SM3D_WRONG_MIN_FACE_ANGLE 8904 Invalid value for ’min_face_angle’
H_ERR_SM3D_WRONG_MIN_SIZE 8905 Invalid value for ’min_size’
H_ERR_SM3D_WRONG_MODEL_TOLERANCE 8906 Invalid value for ’model_tolerance’
H_ERR_SM3D_WRONG_FAST_POSE_REF 8907 Invalid value for ’fast_pose_refinement’
H_ERR_SM3D_WRONG_LOWEST_MODEL_LEVEL 8908 Invalid value for ’lowest_model_level’
H_ERR_SM3D_WRONG_PART_SIZE 8909 Invalid value for ’part_size’
H_ERR_SM3D_PROJECTION_TOO_LARGE 8910 The projected model is too large (the value for DistMin or the
image size in CamParam is too small)
H_ERR_SM3D_WRONG_OPENGL_ACCURACY 8911 Invalid value for ’opengl_accuracy’
H_ERR_SM3D_WRONG_RECOMPUTE_SCORE 8913 Invalid value for ’recompute_score’
H_ERR_SM3D_WRONG_LON_MIN 8920 Invalid value for ’longitude_min’
H_ERR_SM3D_WRONG_LON_MAX 8921 Invalid value for ’longitude_max’
H_ERR_SM3D_WRONG_LAT_MIN 8922 Invalid value for ’latitude_min’
H_ERR_SM3D_WRONG_LAT_MAX 8923 Invalid value for ’latitude_max’
H_ERR_SM3D_WRONG_ROL_MIN 8924 Invalid value for ’cam_roll_min’
H_ERR_SM3D_WRONG_ROL_MAX 8925 Invalid value for ’cam_roll_max’
H_ERR_SM3D_WRONG_DIST_MIN 8926 Invalid value for ’dist_min’
H_ERR_SM3D_WRONG_DIST_MAX 8927 Invalid value for ’dist_max’
H_ERR_SM3D_WRONG_NUM_MATCHES 8928 Invalid value for ’num_matches’
H_ERR_SM3D_WRONG_MAX_OVERLAP 8929 Invalid value for ’max_overlap’
136 HALCON Error Codes

Error Name Code Description

H_ERR_SM3D_WRONG_POSE_REFINEMENT 8930 Invalid value for ’pose_refinement’

H_ERR_SM3D_WRONG_COV_POSE_MODE 8931 Invalid value for ’cov_pose_mode’
H_ERR_SM3D_WRONG_OUTLIER_SUP 8932 Invalid value for ’outlier_suppression’
H_ERR_SM3D_WRONG_BORDER_MODEL 8933 Invalid value for ’border_model’
H_ERR_SM3D_UNDEFINED_POSE 8940 Pose is not well-defined
H_ERR_SM3D_NO_SM3D_FILE 8941 Invalid file format for 3D shape model
H_ERR_SM3D_WRONG_FILE_VERSION 8942 The version of the 3D shape model is not supported
H_ERR_SM3D_MTL 8943 3D shape model data can only be read by HALCON XL
H_ERR_SM3D_NO_OM3D_FACES 8944 3D object model does not contain any faces
H_ERR_SM3D_NOSITEM 8945 Serialized item does not contain a valid 3D shape model
H_ERR_SM3D_WRONG_UNION_ADJACENT_CONTOURS 8946 Invalid value for ’union_adjacent_contours’
H_ERR_DESCR_NODESCRFILE 8960 Invalid file format for descriptor model
H_ERR_DESCR_WRDESCRVERS 8961 The version of the descriptor model is not supported
H_ERR_DM_WRONG_NUM_CIRC_RADIUS 8962 Invalid value for ’radius’
H_ERR_DM_WRONG_NUM_CHECK_NEIGH 8963 Invalid value for ’check_neighbor’
H_ERR_DM_WRONG_NUM_MIN_CHECK_NEIGH 8964 Invalid value for ’min_check_neighbor_diff’
H_ERR_DM_WRONG_NUM_MIN_SCORE 8965 Invalid value for ’min_score’
H_ERR_DM_WRONG_NUM_SIGMAGRAD 8966 Invalid value for ’sigma_grad’
H_ERR_DM_WRONG_NUM_SIGMAINT 8967 Invalid value for ’sigma_smooth’
H_ERR_DM_WRONG_NUM_ALPHA 8968 Invalid value for ’alpha’
H_ERR_DM_WRONG_NUM_THRESHOLD 8969 Invalid value for ’threshold’
H_ERR_DM_WRONG_NUM_DEPTH 8970 Invalid value for ’depth’
H_ERR_DM_WRONG_NUM_TREES 8971 Invalid value for ’number_trees’
H_ERR_DM_WRONG_NUM_MIN_SCORE_DESCR 8972 Invalid value for ’min_score_descr’
H_ERR_DM_WRONG_NUM_PATCH_SIZE 8973 Invalid value for ’patch_size’
H_ERR_DM_WRONG_TILT 8974 Invalid value for ’tilt’
H_ERR_DM_WRONG_PAR_GUIDE 8975 Invalid value for ’guided_matching’
H_ERR_DM_WRONG_PAR_SUBPIX 8976 Invalid value for ’subpix’
H_ERR_DM_TOO_FEW_POINTS 8977 Too few feature points can be found
H_ERR_DM_WRONG_NUM_MINROT 8978 Invalid value for ’min_rot’
H_ERR_DM_WRONG_NUM_MAXROT 8979 Invalid value for ’max_rot’
H_ERR_DM_WRONG_NUM_MINSCALE 8980 Invalid value for ’min_scale’
H_ERR_DM_WRONG_NUM_MAXSCALE 8981 Invalid value for ’max_scale’
H_ERR_DM_WRONG_NUM_MASKSIZEGRD 8982 Invalid value for ’mask_size_grd’
H_ERR_DM_WRONG_NUM_MASKSIZESMOOTH 8983 Invalid value for ’mask_size_smooth’
H_ERR_BROKEN_MODEL 8984 Model broken
H_ERR_DM_WRONG_DESCR_TYPE 8985 Invalid value for ’descriptor_type’
H_ERR_DM_WRONG_PAR_MATCHER 8986 Invalid value for ’matcher’
H_ERR_DM_TOO_MANY_CLASSES 8987 Too many point classes - model storing in a file is not possible
H_ERR_DESCR_NOSITEM 8988 Serialized item does not contain a valid descriptor model
H_ERR_NOT_IMPL 9000 Function not implemented on this machine
H_ERR_WIT 9001 Image to process has wrong gray value type
H_ERR_WIC 9002 Wrong image component (see: get_system(obj_images,H))
H_ERR_UNDI 9003 Undefined gray values
H_ERR_WIS 9004 Wrong image format for operation (too big or too small)
H_ERR_WCN 9005 Wrong number of image components for image output
H_ERR_STRTL 9006 String is too long (max. 1024 characters)
H_ERR_WITFO 9007 Wrong pixel type for this operation
H_ERR_NIIT 9008 Operation not realized yet for this pixel type
H_ERR_NOCIMA 9009 Image is no color image with three channels
H_ERR_DEMO_NOFG 9010 Image acquisition devices are not supported in the demo
version
H_ERR_DEMO_NOPA 9011 Packages are not supported in the demo version
H_ERR_IEUNKV 9020 Internal error: Unknown value
H_ERR_WPFO 9021 Wrong parameter for this operation
H_ERR_IDTS 9022 Image domain too small
 137

Error Name Code Description

H_ERR_CNCLDRW 9023 Draw operator has been canceled

H_ERR_REGEX_MATCH 9024 Error during regular expression matching
H_ERR_STUD_OPNA 9050 Operator is not available in this restricted version of HALCON
H_ERR_STUD_PANA 9051 Packages are not available in this restricted version of
HALCON
H_ERR_STUD_FGNA 9052 The selected image acquisition interface is not available in this
restricted version of HALCON
H_ERR_NDPA 9053 No data points available
H_ERR_WR_OBJ_TYPE 9054 Type of the object is not supported
H_ERR_OP_DISABLED 9055 Operator is disabled
H_ERR_TMU 9100 Too many unknown variables in linear equation
H_ERR_NUS 9101 No (unique) solution for the linear equation
H_ERR_NEE 9102 Too little equations in linear equation
H_ERR_PDDL 9150 Points do not define a line
H_ERR_MNI 9200 Matrix is not invertible
H_ERR_SVD_CNVRG 9201 Singular value decomposition did not converge
H_ERR_SVD_FEWROW 9202 Matrix has too few rows for singular value partition
H_ERR_TQLI_CNVRG 9203 Eigenvalue computation did not converge

Error Codes
H_ERR_JACOBI_CNVRG 9204 Eigenvalue computation did not converge
H_ERR_MATRIX_SING 9205 Matrix is singular
H_ERR_MATCH_CNVRG 9206 Function matching did not converge
H_ERR_MAT_UNDEF 9207 Input matrix undefined
H_ERR_MAT_WDIM 9208 Input matrix with wrong dimension
H_ERR_MAT_NSQR 9209 Input matrix is not quadratic
H_ERR_MAT_FAIL 9210 Matrix operation failed
H_ERR_MAT_NPD 9211 Matrix is not positive definite
H_ERR_MAT_DBZ 9212 One element of the matrix is zero: Division by zero
H_ERR_MAT_NUT 9213 Matrix is not an upper triangular matrix
H_ERR_MAT_NLT 9214 Matrix is not a lower triangular matrix
H_ERR_MAT_NEG 9215 One element of the matrix is negative
H_ERR_MAT_UNCHAR 9216 Matrix file: Invalid character
H_ERR_MAT_NOT_COMPLETE 9217 Matrix file: Matrix incomplete
H_ERR_MAT_READ 9218 Invalid file format for matrix
H_ERR_MAT_COMPLEX 9219 Resulting matrix has complex values
H_ERR_WMATEXP 9220 Wrong value in matrix of exponents
H_ERR_MAT_WRONG_VERSION 9221 The version of the matrix is not supported
H_ERR_MAT_NOSITEM 9222 Serialized item does not contain a valid matrix
H_ERR_WNODE 9230 Internal error: wrong Node
H_ERR_CMP_INCONSISTENT 9231 Inconsistent red black tree
H_ERR_LAPACK_PAR 9250 Internal error: Wrong LAPACK parameter
H_ERR_STRI_NPNT 9260 Number of points too small for spherical triangulation
H_ERR_STRI_COLL 9261 First three points are collinear in spherical triangulation
H_ERR_STRI_IDPNT 9262 Spherical triangulation contains identical input points
H_ERR_STRI_NALLOC 9263 Internal error: array not allocated large enough for spherical
triangulation
H_ERR_STRI_DEGEN 9264 Spherical Voronoi diagram contains degenerate triangle
H_ERR_STRI_ITRI 9265 Internal error: inconsistent spherical triangulation
H_ERR_STRI_SELFINT 9266 Spherical Voronoi diagram contains self-intersecting polygon
H_ERR_STRI_INCONS 9267 Internal error: inconsistent spherical polygon data
H_ERR_STRI_AMBINT 9268 Internal error: Ambiguous great circle arc intersection
H_ERR_STRI_AMBARC 9269 Internal error: Ambiguous great circle arc
H_ERR_STRI_ILLPAR 9270 Internal error: Illegal parameter
H_ERR_TRI_NPNT 9280 Not enough points for planar triangular meshing
H_ERR_TRI_COLL 9281 The first three points of the triangular meshing are collinear
H_ERR_TRI_IDPNT 9282 Planar triangular meshing contains identical input points
H_ERR_TRI_IDPNTIN 9283 Invalid points for planar triangular meshing
138 HALCON Error Codes

Error Name Code Description

H_ERR_TRI_NALLOC 9284 Internal error: allocated array too small for planar triangular
meshing
H_ERR_TRI_ITRI 9285 Internal error: planar triangular meshing inconsistent
H_ERR_TRI_OUTR 9286 Node index outside triangulation range
H_ERR_TRI_LOCINC 9290 Local inconsistencies in all valid neighborhoods (parame-
ters only allow few valid neighborhoods or point cloud not
subsampled)
H_ERR_WSPVP 9300 Eye point and reference point coincide
H_ERR_DQ_ZERO_NORM 9310 Real part of the dual quaternion has length 0
H_ERR_TIMEOUT 9400 Timeout occurred
H_ERR_WRONG_TIMEOUT 9401 Invalid value for timeout
H_ERR_DEFORM_WRONG_NUM_CLUSTER 9450 Invalid value for ’part_size’
H_ERR_DEFORM_WRONG_NUM_MIN_SIZE 9451 Invalid value for ’min_size’
H_ERR_DEFORM_WRONG_NUM_LSQ 9452 Invalid number of least-squares iterations
H_ERR_DEFORM_WRONG_ANGLE_STEP 9453 Invalid value for ’angle_step’
H_ERR_DEFORM_WRONG_SCALE_R_STEP 9454 Invalid value for ’scale_r_step’
H_ERR_DEFORM_WRONG_SCALE_C_STEP 9455 Invalid value for ’scale_c_step’
H_ERR_DEFORM_WRONG_MAX_ANGLE 9456 Invalid value for ’max_angle_distortion’
H_ERR_DEFORM_WRONG_MAX_ANISO 9457 Invalid value for ’max_aniso_scale_distortion’
H_ERR_DEFORM_WRONG_MIN_SIZE 9458 Invalid value for ’min_size’
H_ERR_DEFORM_WRONG_COV_POSE_MODE 9459 Invalid value for ’cov_pose_mode’
H_ERR_DEFORM_NO_CALIBRATION_INFO 9460 Model contains no calibration information
H_ERR_DEFORM_WRONG_PARAM_NAME 9461 Generic parameter name does not exist
H_ERR_DEFORM_IMAGE_TO_CAMERA_DIFF 9462 Provided camera parameters have different resolution than
image
H_ERR_DEFORM_NO_MODEL_IN_FILE 9463 Invalid file format for deformable model
H_ERR_DEFORM_WRONG_VERSION 9464 The version of the deformable model is not supported
H_ERR_DEFORM_WRONG_SMOOTH_DEFORM 9465 Invalid ’deformation_smoothness’
H_ERR_DEFORM_WRONG_EXPAND_BORDER 9466 Invalid ’expand_border’
H_ERR_DEFORM_ORIGIN_OUTSIDE_TEMPLATE 9467 Model origin outside of axis-aligned bounding rectangle of
template region
H_ERR_DEFORM_NOSITEM 9468 Serialized item does not contain a valid deformable model
H_ERR_VIEW_ESTIM_FAIL 9499 Estimation of viewpose failed
H_ERR_SFM_NO_POINTS 9500 3D Object Model has no points
H_ERR_SFM_NO_FACES 9501 3D Object Model has no faces
H_ERR_SFM_NO_NORMALS 9502 3D Object Model has no normals
H_ERR_SFM_NO_VISIBILITY 9503 3D surface model not trained for calculating view-based score
H_ERR_SFM_NO_3D_EDGES 9504 3D surface model not trained for edge-supported matching
H_ERR_SFM_NO_SFM_FILE 9506 Invalid file format for 3D surface model
H_ERR_SFM_WRONG_FILE_VERSION 9507 The version of the 3D surface model is not supported
H_ERR_SFM_NOSITEM 9508 Serialized item does not contain a valid 3D surface model
H_ERR_SFM_TOO_MANY_SYMMS 9509 Given symmetry poses generate too many symmetric poses
H_ERR_OM3D_INVALID_FILE 9510 Invalid 3D file
H_ERR_OM3D_INVALID_MODEL 9511 Invalid 3D object model
H_ERR_OM3D_UNKNOWN_FILE_TYPE 9512 Unknown file type
H_ERR_OM3D_WRONG_FILE_VERSION 9513 The version of the 3D object model is not supported
H_ERR_OM3D_MISSING_ATTRIB 9514 Required attribute missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_V_COORD 9515 Required points missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_V_NORMALS 9516 Required normals missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_F_TRIANGLES 9517 Required triangulation missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_F_LINES 9518 Required polylines missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_F_TRINEIGB 9519 Required triangle neighborhood missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_F_POLYGONS 9520 Required polygons missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_V_2DMAP 9521 Required 2D mapping missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_O_PRIMITIVE 9522 Required primitive missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_SHAPE_MODEL 9523 Required 3D shape model missing in 3D object model
H_ERR_OM3D_MISSING_ATTRIB_EXTENDED 9524 Required extended attribute missing in 3D object model
 139

Error Name Code Description

H_ERR_OM3D_NOSITEM 9525 Serialized item does not contain a valid 3D object model
H_ERR_OM3D_MISSING_O_PRIMITIVE_EXTENSION 9526 Primitive in 3D object model has no extended data
H_ERR_OM3D_CONTAIN_ATTRIB_F_TRIANGLES 9527 Operation invalid, 3D object model already contains triangles
H_ERR_OM3D_CONTAIN_ATTRIB_F_LINES 9528 Operation invalid, 3D object model already contains lines
H_ERR_OM3D_CONTAIN_ATTRIB_F_POLYGONS 9529 Operation invalid, 3D object model already contains faces or
polygons
H_ERR_OM3D_ISOLATED_OBJECT 9530 For at least one input 3D object model no neighbor with suffi-
cient surface overlap is available
H_ERR_OM3D_SET_ALL_COORD 9531 All components of points must be set at once
H_ERR_OM3D_SET_ALL_NORMALS 9532 All components of normals must be set at once
H_ERR_OM3D_NUM_NOT_FIT_COORD 9533 Number of values does not correspond to number of already
existing points
H_ERR_OM3D_NUM_NOT_FIT_NORMALS 9534 Number of values does not correspond to number of already
existing normals
H_ERR_OM3D_NUM_NOT_FIT_TRIANGLES 9535 Number of values does not correspond to already existing
triangulation
H_ERR_OM3D_NUM_NOT_FIT_POLYGONS 9536 Number of values does not correspond to length of already ex-
isting polygons
9537 Number of values does not correspond to length of already ex-

Error Codes
H_ERR_OM3D_NUM_NOT_FIT_LINES
isting polylines
H_ERR_OM3D_NUM_NOT_FIT_2DMAP 9538 Number of values does not correspond to already existing 2D
mapping
H_ERR_OM3D_NUM_NOT_FIT_EXTENDED 9539 Number of values does not correspond to already existing ex-
tended attribute
H_ERR_OM3D_FACE_INTENSITY_WITH_POINTS 9540 Per-face intensity is used with attribute ’points’
H_ERR_OM3D_ATTRIBUTE_NOT_SUPPORTED 9541 At least one attribute is not supported
H_ERR_OM3D_NOT_IN_BB 9542 No point within bounding box
H_ERR_DIF_TOO_SMALL 9543 distance_in_front is smaller than the ’Resolution’
H_ERR_MINTH_TOO_SMALL 9544 The minimum thickness is smaller than the surface tolerance
H_ERR_OM3D_WRONG_DIMENSION 9545 Input width or height does not match the number of points in
3D object model
H_ERR_OM3D_MISSING_DIMENSION 9546 Image width or height must be set to compute the XYZ-
mapping
H_ERR_SF_OM3D_TRIANGLES_NOT_SUITABLE 9550 Triangles of the 3D object model are not suitable for this
operator
H_ERR_SF_OM3D_FEW_POINTS 9551 Too few suitable 3D points in the 3D object model
H_ERR_NO_SERIALIZED_ITEM 9580 Invalid file format for serialized items
H_ERR_END_OF_FILE 9581 Serialized item: premature end of file
H_ERR_SID_WRONG_RESIZE_METHOD 9600 Invalid value for ’image_resize_method’
H_ERR_SID_WRONG_RESIZE_VALUE 9601 Invalid value for ’image_resize_value’
H_ERR_SID_WRONG_RATING_METHOD 9602 Invalid value for ’rating_method’
H_ERR_SID_NO_IMAGE_INFO_TYPE 9603 At least one type of image information must be added
H_ERR_SID_MODEL_NO_COLOR 9604 Sample identifier does not contain color information
H_ERR_SID_MODEL_NO_TEXTURE 9605 Sample identifier does not contain texture information
H_ERR_SID_NO_IMAGE_INFO 9606 Sample image does not contain enough information
H_ERR_SID_NO_UNPREPARED_DATA 9607 Sample identifier does not contain unprepared data (use
add_sample_identifier_preparation_data)
H_ERR_SID_MODEL_NOT_PREPARED 9608 Sample identifier has not been prepared yet (use
prepare_sample_identifier)
H_ERR_SID_NO_UNTRAINED_DATA 9609 Sample identifier does not contain untrained data (use
add_sample_identifier_training_data)
H_ERR_SID_MODEL_NOT_TRAINED 9610 Sample identifier has not been trained yet (use
train_sample_identifier)
H_ERR_SID_NO_RESULT_DATA 9611 Sample identifier does not contain result data
H_ERR_SID_NUM_TRAIN_OBJ 9612 Sample identifier must contain at least two training objects (use
add_sample_identifier_training_data)
H_ERR_FINI_USR_THREADS 9700 More than one user thread still uses HALCON resources dur-
ing finalization
H_ERR_NO_ENCRYPTED_ITEM 9800 Invalid file format for encrypted items
H_ERR_WRONG_PASSWORD 9801 Wrong password
140 HALCON Error Codes

Error Name Code Description

H_ERR_ENCRYPT_FAILED 9802 Encryption failed

H_ERR_DECRYPT_FAILED 9803 Decryption failed
 HALCON Semantic Types 141

Appendix B

HALCON Semantic Types

In the following, the HALCON semantic types are listed. For more information about semantic types, see sec-
tion 2.3.3 on page 29.
angle any arc attribute
barcode barrier bead_inspection_model bg_estimation
calib_data camera_setup_model campar chain
channel chord circle circle_arc
circle_sector class_box class_gmm class_knn
class_lut class_mlp class_svm class_train_data
color_trans_lut component_model component_training compute_device
condition contour coordinates datacode_2d
deep_counting deep_matching_3d deep_ocr deformable_model
deformable_surface_matching_result deformable_surface_model descriptor_model dev_tool

Semantic Types
dict distribution dl_classifier dl_classifier_result
dl_classifier_train_result dl_device dl_layer dl_model
dl_pruning drawing_object dual_quaternion ellipse
ellipse_arc ellipse_sector encrypted_item event
exception extent feature_set file
filename framegrabber function_1d generic_shape_model_result
grayval handle hesseline histogram
hom_mat2d hom_mat3d iline image
info integer io_channel io_device
lexicon line matrix measure
memory_block message message_queue metrology_model
mutex ncc_model number object
object_model_3d ocr_box ocr_cnn ocr_knn
ocr_mlp ocr_svm ocv operator_set
point point3d pointer polygon
pose proc_name quaternion real
rectangle rectangle2 region sample_identifier
scanner scattered_data_interpolator scene_3d serial
serialized_item shape_model shape_model_3d sheet_of_light_model
socket stereo_model string structured_light_model
surface_matching_result surface_model system template
text_model text_result texture_inspection_model texture_inspection_result
thread_id tuple untyped_object user
variation_model window xld xld_cont
xld_dist_trans xld_ext_para xld_mod_para xld_para
xld_poly
142 HALCON Semantic Types
 Index 143

Index

abort_mode, 26 control parameters, 72

abstract, 21 costs_weight, 31
accessing iconic objects, 57, 62 CYCLIC_IMAGE, 50
action procedure, 13, 16, 46
alternatives, 23 data types, 49
area of definition, 48 HComplexPixel, 51
arrays, 40 Hcont, 44, 53, 54, 62, 71
assertion, 33, 34 Hcpar, 55, 72, 74, 76, 78–80, 88
attention, 23 Herror (C), 46, 47, 83
Himage, 43, 48, 50, 61, 64, 70, 87, 89
border treatment, 83 HInt2Pixel, 51
buffer, 10 Hkey, 57, 60, 61
BYTE_IMAGE, 50, 70, 91 Hobject (C), 10
Hpar, 55
C, 14, 21, 27, 39, 98 HPixelImage, 50
C++, 14, 21, 23, 27, 98 Hpoly, 53, 62, 71
C#, 14, 23, 27, 98 HRegFeature, 52
CB, 52, 84, 91, 93 Hrlregion, 42, 51, 51, 52, 60, 62, 63, 69, 87
CE, 52, 84, 91, 93 Htuple (C), 10
center of gravity, 88 HUInt2Pixel, 51
channel, 61, 89 numeric types, 39
channels, 59, 89, 90 database key, 55, 57, 59–62, 64, 66–70
chapter, 22 database of iconic objects, 9, 42, 43, 49, 51, 57, 62,
chord, 50, 51 67–71
class of a parameter, 29 default_type, 15, 29
comments, 20 default_value, 32
COMPLEX_IMAGE, 50 definition file (DEF file), 14
complexity, 27 description, 32

Index
constants DIR_IMAGE, 50
BYTE_IMAGE, 50, 70, 91 directories
COMPLEX_IMAGE, 50 bin, 12
CYCLIC_IMAGE, 50 def, 12
DIR_IMAGE, 50 doc, 12, 13
FLOAT_IMAGE, 50, 70 examples, 12
IMAGE1, 59 help, 12, 13
IMAGE2, 59 images, 12
IMAGE_INDEX, 59, 69 include, 12
INT1_IMAGE, 50 lib, 12
INT2_IMAGE, 50 domain, 59, 66, 68, 87–90
INT4_IMAGE, 50 domain_concat_mult_inp, 26
INT8_IMAGE, 50 domain_concat_si_inp, 26
LONG_IMAGE, 50, 70 DOUBLE_PAR, 55, 72, 74–76, 79–81
LONG_PAR, 55, 72, 74–76, 79–81
MAX_FORMAT, 48, 49 environment variables
REGION, 59 HALCONEXAMPLES, 104
STRING_PAR, 55, 72, 74–76, 79–81 HALCONEXTENSIONS, 9, 13, 100, 101, 103
UINT2_IMAGE, 50 HALCONROOT, 104
VF_IMAGE, 50 LD_LIBRARY_PATH, 14, 104
XLD_CONTOUR_ID, 62, 71 error codes, 47
XLD_POLYGON_ID, 62, 71 error handling (HALCON)
contour attributes, 52, 54 error codes
144 Index

H_ERR_ICM, 46 HCkP, 16, 47, 57, 59–66, 68–72, 74, 76–82, 83, 84,
H_ERR_WIT, 48, 91 85, 89–91, 93–95
H_ERR_XLD_CAND, 55 HCol, 49
H_MSG_OK, 46, 83 hcomp, 15, 97
H_MSG_TRUE, 10, 46 HComplexPixel, 51
etags, 98 Hcont, 44, 53, 54, 62, 71
example, 27 HCopyElemD, 76, 77, 78
HCopyElemL, 76, 77, 78
feature extraction, 48, 88 HCopyObj, 67, 68, 69, 71, 90, 94
file_ext, 35 HCopyXLDCont, 54
file_ext_descr, 35 HCopyXLDContPart, 54
files Hcpar, 55, 72, 74, 76, 78–80, 88
HCpackage.c, 100 HCrImage, 66–68, 70
HCpackage.h, 100 HCrObj, 66, 67, 67, 69, 70, 94, 95
HCpackage.obj, 102 HCrXLD, 68, 71
HCPPpackage.cpp, 101 HDefObj, 66–69, 69, 70, 71
HCPPpackage.h, 101 HDevelop, 14–16, 22, 23, 98
filter, 48, 70, 83, 87, 90 HDFImage, 91, 92, 92, 93
FLOAT_IMAGE, 50, 70 HDoLowError, 46
functionality, 23 HDOTNETpackage.cs, 98, 101, 102
HDupObj, 93, 94
global variables, 41 help files, 16, 35, 98
graphics software, 9 Herror, 46, 47, 83
HErrorDef.h, 47
H_ERR_ICM, 46
HFree, 44, 75
H_ERR_WIT, 48, 91
HFreeAllTmp, 41
H_ERR_XLD_CAND, 55
HFreeLocal, 42, 75
H_MSG_OK, 46, 83
HFreeNTmp, 41
H_MSG_TRUE, 10, 46
HFreeRL, 45
HAddXLDContAttrib, 54
HFreeRLLocal, 42
HAddXLDContGlobalAttrib, 54
HFreeRLTmp, 41, 61–64, 84, 90, 92–94
HALCON, 41
HFreeTmp, 41, 75
HALCON XL, 12
HFreeUpToTmp, 41, 85
HALCON/.NET, 10
HFreeXLDCont, 44
HALCON/C++, 10
HGetCElemH, 72, 76
HALCONEXAMPLES, 104
HGetCElemH1, 72, 76
HALCONEXTENSIONS, 9, 13, 100, 101, 103
HGetCElemH1, HGetCElemH, HGetCElemHN, 75
HALCONROOT, 104
HGetCElemHN, 72, 76
HAllComp, 65, 66, 89, 90
HGetComp, 58, 59, 61, 62, 64, 71
HAllFilter, 87, 88, 90, 92, 95
HGetCPar, 16, 72, 72, 74, 76, 77, 78
HAllFilter2, 87, 88, 92
HGetCParNum, 77
HAllObj, 59, 62, 65, 66, 66, 71, 88–90
HGetDImage, 63, 64, 64, 66
HAlloc, 43, 44, 44, 45, 71, 75, 79–82
HGetDRL, 62, 63
HAllocLocal, 42, 43, 45, 75
HGetElemD, 72, 77
HAllocOutputHandle, 43
HGetElemL, 72, 77
HAllocRL, 45
HGetElemL, HGetElemD, HGetElemS, 75
HAllocRLLocal, 42, 43
HGetElemS, 72, 77
HAllocRLNum, 45
HGetFDRL, 60, 62, 63, 66, 69, 71, 88–90
HAllocRLNumLocal, 42
HGetImage, 58, 60, 61, 64, 71
HAllocRLNumTmp, 41, 51, 84
HGetObj, 57, 58, 60–63, 65, 66, 69, 94
HAllocRLTmp, 41, 42, 51, 61–64, 85, 90, 92–94
HGetObjNum, 59, 63, 65, 65
HAllocStringMem, 77, 78, 79, 80
HGetPElem, 72, 73, 74, 77
HAllocTmp, 41, 46, 75, 80
HGetPElemD, 72, 73
HAllocXLDCont, 44, 72
HGetPElemL, 72, 73
HAllReg, 87, 88, 88, 89, 94, 95
HGetPElemS, 72, 73
HAllSegm, 16, 87, 88, 89, 91
HGetPPar, 72, 73, 74, 77
HANDLE_PAR, 55, 72
HGetRL, 58, 60, 61, 62
HBase.h, 49
HGetSPar, 64, 71, 77, 80, 91, 95
HCkNoObj, 82, 83
HGetURL, 62, 63, 63, 85
 Index 145

HGetXLD, 58, 62 image processing hardware, 9

Himage, 43, 48, 50, 61, 64, 70, 87, 89 image size, 49, 90
HImageFD, 91, 92, 92, 93 image vector, 49
HIncrRL, 84 IMAGE1, 59
HInt2Pixel, 51 IMAGE2, 59
Hkey, 57, 60, 61 IMAGE_INDEX, 59, 69
HLinCoor, 49, 61, 64 images, 49
HLookupXLDContAttrib, 54 include files (HALCON)
HLookupXLDContGlobalAttrib, 54 HBase.h, 49
HMEMglobal, 75 IPType.h, 49
HMEMlocal, 75 index, 59, 87
HMEMtemp, 75 input control parameter, 72, 74–76, 91
HNewImage, 44, 95 INT1_IMAGE, 50
HNewImagePtr, 44 INT2_IMAGE, 50
HNewRegion, 16, 88, 90, 93, 94, 95 INT4_IMAGE, 50
HNumOfChannels, 60, 82, 84, 89 INT8_IMAGE, 50
Hobject, 10 IPType.h, 49
Hpackage.c, 98, 100
Hpar, 55 keywords, 23
HPGetURL, 85
LD_LIBRARY_PATH, 14, 104
HPixelImage, 50
linear coordinate, 49
HPNumOfChannels, 59, 60, 84
Linux, 11, 14, 103
Hpoly, 53, 62, 71
local variables, 40
HPutCPar, 62, 64, 72, 79, 80, 81, 88, 89
LONG_IMAGE, 50, 70
HPutDImage, 68, 70, 90, 95
LONG_PAR, 55, 72, 74–76, 79–81
HPutDRL, 67–69, 69, 70
HPutElem, 72, 80, 81 MAX_FORMAT, 48, 49
HPutElemH, 72, 80 memory costs, 95
HPutImage, 44, 67–69, 69, 70 memory management, 41
HPutPElem, 72, 79, 81 method, 25
HPutPPar, 72, 79, 81 MIXED_PAR, 72, 74
HPutRect, 68, 93, 94 modified, 30
HReadGV, 43, 59 module, 22
HReadGVA, 59, 59, 65, 69 multi-channel image, 49
HRealloc, 44 multichannel, 10, 34
HReallocLocal, 42 multiinstance, 35
HReallocRLNum, 45 multivalue, 10, 30

Index
HReallocRLNumLocal, 42 multivalues, 35
HRegFeature, 52
HRLArea, 88 Name, 28
HRLDecomp, 82, 83, 83
Hrlregion, 42, 51, 51, 52, 60, 62, 63, 69, 87 operator description, 19
HRow, 49 abstract, 21
HSetErrText, 47 alternatives, 23
HTestAllTmp, 45 assertion, 33, 34
HTestMem, 45 attention, 23
HTestPtr, 45 chapter, 22
HTestTmp, 45 complexity, 27
HTML reference, 13 costs_weight, 31
Htuple, 10 default_type, 15, 29
HUInt2Pixel, 51 default_value, 32
HVFPixel, 51 description, 32
HWriteGV, 43 example, 27
HXLDFreeContour, 71 file_ext, 35
HXLDFreePolygon, 72 file_ext_descr, 35
functionality, 23
iconic object key, 10 keywords, 23
image component, 59 languages, 20
image components, 67 method, 25
image matrix, 49, 59, 69, 70 module, 22
146 Index

multichannel, 10, 34 supply procedure, 13, 15, 16, 46, 87, 90, 98
multivalue, 10, 30 parallelization, 24
Name, 28 parameter classes, 19, 21
parallelization, 24 Parameters, 40
postprocessing, 31 ParRef, 36
predecessor, 23 pixel data, 49, 87
process_exclusively, 24 pixel type, 48, 49, 70, 90
process_locally, 25 pixel types, 49, 89
process_mutual, 25 postprocessing, 31
references, 27 predecessor, 23
region_postprocessing, 25 procedure handle, 10
result_state, 24 procedure names, 46
see_also, 23 procedures/macros
sem_type, 15, 29, 32 accessing control parameters
short, 21 HAllocStringMem, 77, 78, 79, 80
step_min, 33 HGetCPar, 16, 72, 72, 74, 76, 77, 78
step_rec, 33 HGetCParNum, 77
successor, 23 HGetPPar, 72, 73, 74, 77
type_list, 32 HGetSPar, 64, 71, 77, 80, 91, 95
value_function, 33 HPutCPar, 62, 64, 72, 79, 80, 81, 88, 89
value_list, 33 HPutPPar, 72, 79, 81
value_max, 33 accessing iconic objects
value_min, 33 CB, 52, 84, 91, 93
value_number, 33 CE, 52, 84, 91, 93
values, 33 HAddXLDContAttrib, 54
operators_en_US.idx, 98 HAddXLDContGlobalAttrib, 54
operators_en_US.key, 98 HCkNoObj, 82, 83
operators_en_US.num, 98 HCol, 49
operators_en_US.ref, 98 HCopyObj, 67, 68, 69, 71, 90, 94
operators_en_US.sta, 98 HCopyXLDCont, 54
OpRef, 36 HCopyXLDContPart, 54
origin of an image, 49 HCrImage, 66–68, 70
output iconic parameter, 67 HCrObj, 66, 67, 67, 69, 70, 94, 95
output image, 90 HCrXLD, 68, 71
HDefObj, 66–69, 69, 70, 71
package, 11 HDFImage, 91, 92, 92, 93
action procedure, 13, 16, 46 HDupObj, 93, 94
directories HGetComp, 58, 59, 61, 62, 64, 71
bin, 12 HGetDImage, 63, 64, 64, 66
def, 12 HGetDRL, 62, 63
doc, 12, 13 HGetFDRL, 60, 62, 63, 66, 69, 71, 88–90
examples, 12 HGetImage, 58, 60, 61, 64, 71
help, 12, 13 HGetObj, 57, 58, 60–63, 65, 66, 69, 94
images, 12 HGetObjNum, 59, 63, 65, 65
include, 12 HGetRL, 58, 60, 61, 62
lib, 12 HGetURL, 62, 63, 63, 85
files HGetXLD, 58, 62
definition file, 14 HImageFD, 91, 92, 92, 93
HCpackage.c, 100 HLinCoor, 49, 61, 64
HCpackage.h, 100 HLookupXLDContAttrib, 54
HCpackage.obj, 102 HLookupXLDContGlobalAttrib, 54
HCPPpackage.cpp, 101 HNewRegion, 16, 88, 90, 93, 94, 95
HCPPpackage.h, 101 HNumOfChannels, 60, 82, 84, 89
help files, 16, 35, 98 HPNumOfChannels, 59, 60, 84
reference manual HPutDImage, 68, 70, 90, 95
HTML, 98 HPutDRL, 67–69, 69, 70
OpRef, 36 HPutImage, 44, 67–69, 69, 70
ParRef, 36 HPutRect, 68, 93, 94
PDF, 99 HRow, 49
ValRef, 36
 Index 147

basic references, 27
HCkP, 16, 47, 57, 59–66, 68–72, 74, 76–82, REGION, 59
83, 84, 85, 89–91, 93–95 region, 62
HDoLowError, 46 region data, 50
HReadGV, 43, 59 region shape features, 51, 52
HReadGVA, 59, 59, 65, 69 region transformation, 94
HRLDecomp, 82, 83, 83 region_postprocessing, 25
HSetErrText, 47 result_state, 24
HWriteGV, 43 runlength encoding, 60, 62
loop macros
HAllComp, 65, 66, 89, 90 see_also, 23
HAllFilter, 87, 88, 90, 92, 95 segmentation, 48, 87, 89, 90, 94
HAllFilter2, 87, 88, 92 sem_type, 15, 29, 32
HAllObj, 59, 62, 65, 66, 66, 71, 88–90 semantic type, 29
HAllReg, 87, 88, 88, 89, 94, 95 short, 21
HAllSegm, 16, 87, 88, 89, 91 size, 70, 89
memory management split_channel, 25
HAlloc, 43, 44, 44, 45, 71, 75, 79–82 split_domain, 25
HAllocLocal, 42, 43, 45, 75 split_partial, 25
HAllocRL, 45 split_partial_domain, 25
HAllocRLLocal, 42, 43 split_tuple, 25
HAllocRLNum, 45 static, 41
HAllocRLNumLocal, 42 step_min, 33
HAllocRLNumTmp, 41, 51, 84 step_rec, 33
HAllocRLTmp, 41, 42, 51, 61–64, 85, 90, 92– STRING_PAR, 55, 72, 74–76, 79–81
94 successor, 23
HAllocTmp, 41, 46, 75, 80 supply procedure, 13, 15, 16, 46, 87, 90, 98
HAllocXLDCont, 44, 72
HFree, 44, 75 tuples, 88
HFreeAllTmp, 41 type_list, 32
HFreeLocal, 42, 75
UINT2_IMAGE, 50
HFreeNTmp, 41
union, 63
HFreeRL, 45
user_thresh, 14, 15
HFreeRLLocal, 42
HFreeRLTmp, 41, 61–64, 84, 90, 92–94 ValRef, 36
HFreeTmp, 41, 75 value_function, 33
HFreeUpToTmp, 41, 85 value_list, 33

Index
HFreeXLDCont, 44 value_max, 33
HNewImage, 44, 95 value_min, 33
HNewImagePtr, 44 value_number, 33
HRealloc, 44 values, 33
HReallocLocal, 42 VF_IMAGE, 50
HReallocRLNum, 45
HReallocRLNumLocal, 42 warning, 21
HTestAllTmp, 45 Windows, 11, 14, 101
HTestMem, 45
HTestPtr, 45 XLD, 58, 68, 71, 94
HTestTmp, 45 XLD_CONTOUR_ID, 62, 71
HXLDFreeContour, 71 XLD_POLYGON_ID, 62, 71
HXLDFreePolygon, 72 XLDs, 9, 29, 52
process_exclusively, 24
process_locally, 25
process_mutual, 25

reference manual
HTML, 98
OpRef, 36
ParRef, 36
PDF, 99
ValRef, 36