●SI-3000J Series

SI-3000J Series
5-Terminal, Multi-Function, Full-Mold, Low Dropout Voltage Dropper Type

■Features
• Compact full-mold package (equivalent to TO220)
• Output current: 2.0A
• Low dropout voltage: VDIF≤1V (at IO=2.0A)
• Variable output voltage (rise only) May be used for remote sensing
• Output ON/OFF control terminal is compatible with LS-TTL. (It may be
directly driven by LS-TTL or standard CMOS logic.)
• Built-in foldback overcurrent, overvoltage, thermal protection circuits

■Applications
• For stabilization of the secondary stage of switching power supplies
• Electronic equipment

■Absolute Maximum Ratings (Ta=25°C)

Ratings
Parameter Symbol Unit
SI-3050J SI-3090J SI-3120J/3150J
DC Input Voltage VIN 25 30 35 V
Voltage of Output Control Terminal VC VIN V
DC Output Current IO 2.0*1 A
PD1 20(With infinite heatsink) W
Power Dissipation
PD2 1.5(Without heatsink, stand-alone operation) W
Junction Temperature Tj –40 to +125 °C
Ambient Operating Temperature Top –30 to +100 °C
Storage Temperature Tstg –40 to +125 °C
Thermal Resistance (junction to case) Rth(j-c) 5.0 °C/W
Thermal Resistance (junction to ambient air) Rth(j-a) 66.7(Without heatsink, stand-alone operation) °C/W

46
 ●SI-3000J Series

■Electrical Characteristics (Ta=25°C unless otherwise specified)

Ratings
Parameter Symbol SI-3050J SI-3090J SI-3120J SI-3150J Unit
min. typ. max. min. typ. max. min. typ. max. min. typ. max.
Input Voltage VIN 6*2 15*1 10*2 25*1 13*2 27*1 16*2 27*1 V
VO 4.90 5.00 5.10 8.82 9.00 9.18 11.76 12.00 12.24 14.70 15.00 15.30
Output Voltage V
Conditions VIN=8V, IO=1.0A VIN=12V, IO=1.0A VIN=15V, IO=1.0A VIN=18V, IO=1.0A
VDIF 0.5 0.5 0.5 0.5
Conditions IO≤1.5A
Dropout Voltage V
1.0 1.0 1.0 1.0
Conditions IO≤2.0A
∆VOLINE 10 30 18 48 24 64 30 90
Line Regulation mV
Conditions VIN=6 to 15V, IO=1.0A VIN=10 to 20V, IO=1.0A VIN=13 to 25V, IO=1.0A VIN=16 to 25V, IO=1.0A
∆VOLOAD 40 100 70 180 93 240 120 300
Load Regulation mV
Conditions VIN=8V, IO=0 to 2.0A VIN=12V, IO=0 to 2.0A VIN=15V, IO=0 to 2.0A VIN=18V, IO=0 to 2.0A
Temperature Coefficient ∆VO/∆Ta ±0.5 ±1.0 ±1.5 ±1.5
mV/°C
of Output Voltage Conditions VIN=8V, IO=5mA, Tj=0 to 100°C VIN=12V, IO=5mA, Tj=0 to 100°C VIN=15V, IO=5mA, Tj=0 to 100°C VIN=18V, IO=5mA, Tj=0 to 100°C
RREJ 54 54 54 54
Ripple Rejection dB
Conditions VIN=8V, f=100 to 120HZ VIN=12V, f=100 to 120HZ VIN=15V, f=100 to 120HZ VIN=18V, f=100 to 120HZ
Iq 3 10 3 10 3 10 3 10
mA
Quiescent Circuit Conditions VIN=8V, IO=0A VIN=12V, IO=0A VIN=15V, IO=0A VIN=18V, IO=0A
Current Iq(off) 0.5 1.0 0.5 1.0 0.5 1.0 0.5 1.0
mA
Conditions VIN=8V, IO=0A, VC=0.4V VIN=12V, IO=0A, VC=0.4V VIN=15V, IO=0A, VC=0.4V VIN=18V, IO=0A, VC=0.4V
Overcurrent Protection IS1 2.1 2.1 2.1 2.1
A
Starting Current*3,5 Conditions VIN=8V VIN=12V VIN=15V VIN=18V
Control Voltage (Output ON) VC. IH 2.0 2.0 2.0 2.0
V
Control Voltage (Output OFF) VC. IL 0.8 0.8 0.8 0.8
VC Control Current IC. IH 20 20 20 20
µA
*4
Terminal (Output ON) Conditions VC=2.7V
Control Current IC. IL –0.3 –0.3 –0.3 –0.3
mA
(Output OFF) Conditions VC=0.4V

*1: VIN(max) and IO(max) are restricted by the relation PD(max)=(VIN-VO)•IO=20(W).

*2: Refer to the dropout voltage.(Refer to Setting DC Input Voltage on page 7.)
*3: IS1 is specified at –5(%) drop point of output voltage VO on the condition that VIN=VO+3V, IO=0.5A.
*4: Output is ON even when output control terminal VC is open. Each input level is equivalent to LS-TTL. Therefore, it may be directly driven by an
LS-TTL circuit.
*5: A foldback type overcurrent protection circuit is built into the IC regulator. Therefore, avoid using it for the following applications as it may cause
starting errors:
(1) Constant current load (2) Plus/minus power (3) Series power (4) VO adjustment by raising ground voltage

47
●SI-3000J Series

■Outline Drawing (unit:mm)

φ 3.2±0.2
4.2±0.2
10.0±0.2 2.8
±0.2

0.5
4.0±0.2
7.9±0.2
16.9±0.3

Part Number

(17.9)
Plastic Mold Package Type
Lot Number
Flammability: UL94V-0
2.6±0.1
Weight: Approx. 2.3g

(2.0)
5.0±0.6
0.95
±0.15 q GND
+0.2
w VC
(4.6)

0.85 –0.1
e VO
(8.0)

0.45 –0.1
+0.2 r VOS
t VIN
P1.7±0.7×4=6.8±0.7 3.9±0.7 (4.3)
8.2±0.7

Forming No. 1101

1 2 3 4 5

■Block Diagram

SI-3000J

Tr1
5 3

MIC
4
Drive

Amp.
Reg.
ON/OFF

Protection

VREF

Equivalent
to LS-TTL

■Standard External Circuit

C0 : Output capacitor (47 to 100µF)

D1
*2 *1 C1 : Oscillation prevention capacitor (C1: Approx. 47µF,
C2 C2: 0.33µF)
These capacitors are required if the input line is inductive
5 3
OPEN SI-3000J and in the case of long wiring. Tantalum capacitors are rec-
+ *1 2 4 +
DC Input 1 C0 DC Output ommended for C1 and C0, particularly at low temperatures.
VIN C1 C2
VO
*2 D1 : Protection diode
This diode is required for protection against reverse bias-
ing of the input and output. Sanken EU2Z is recommended.

48
 ●SI-3000J Series

■Ta-PD Characteristics

25
With Silicon Grease: G746
(SHINETSU CHEMICAL
INDUSTRIES)
Infinite heatsink Heatsink: Aluminum
20
Power Dissipation PD (W)

15
200×200×2mm (2.3°C/W)

100×100×2mm (5.2°C/W)
10
75×75×2mm (7.6°C/W)

Without heatsink
0
–30 0 25 50 75 100
Ambient Temperature Ta (°C)

PD=IO•[VIN(mean)–VO]

49
●SI-3000J Series

External Variable Output Voltage Circuit

1. Variable output voltage with a single external resistor

VIN VO 25
5 3

SI-3000J IREX REX VIN=VO+1V 0J

+ OPEN + 15
-3
2 4 V04 SI
47µF 1 47µF

20 0J
GND 12
-3
GND SI

Output Voltage VO (V)

0J
09
The output voltage may be increased by inserting resistor REX between -3
SI
terminals No.4 (sensing terminal) and No.3 (output terminal). The cur-
15
rent IREX flowing into terminal No.4 is 1mA (typ.), therefore the adjusted
0J
output voltage VOUT is: 05
-3
SI
VO=V04+IREX•REX *V04: output voltage of SI-3000J series
However, the built-in resistor (between terminals No. 4 and No.1) is a
semiconductor resistor, which has approximately thermal characteris- 10

tics of +0.2%/°C.
It is important to keep the thermal characteristics in mind when adjust-
ing the output voltage.
5
0 2 4 6 8 10
2. Variable output voltage with two external resistors External Resistor REX (kΩ)
VIN VO
5 3

SI-3000J IREX1 REX1

+ OPEN + 25
2 4 V04
47µF 1 47µF
I4IN REX2 0J
VIN=VO+1V 15 Ω
GND I -3 .75k
S =3
GND X2
RE

20 0J
12
-3 kΩ
The output voltage may be increased by inserting resistors REX1 be- SI X2=3
RE
Output Voltage VO (V)

tween terminals No.4 (sensing terminal) and No.3 (output terminal) and
REX2 between terminals No.4 and No.1 (ground terminal). 90 5kΩ
J
-30 .2
The current I4IN flowing into terminal No.4 is 1mA (typ.) so the thermal SI X2=2
15 RE
characteristics may be improved compared to the method shown in 1
by setting the external current IREX1 at approximately 5 times the value
0J kΩ
of I4IN (stability coefficient S=5). 05 .25
-3
SI X2=1
The adjusted output voltage VOUT in this case is: RE

VO=V04+REX1•IREX1 10
IREX1=S•I4IN
The value of the external resistors may be obtained as follows:
VO-V04 V04
REX1= REX2=
S•I4IN , (S-1)•I4IN 5
*V04: Output voltage of SI=3000J series 0 1.0 2.0
External Resistor REX1 (kΩ)
S: Stability coefficient of I4IN (may be set to any value)

Note: In the SI-3000J series, the output voltage increase can be ad-
justed as mentioned above. However, when the rise is set to ap-
proximately 10V compared to output voltage V04, the necessary
output current may not be obtained due to the S.O.A. protection
circuit in the SI-3000J series.

50
 ●SI-3000J Series

■Typical Characteristics
(Ta=25°C)

IO vs. VDIF Characteristics Temperature Coefficient of Output Voltage(SI-3050J) Circuit Current(SI-3050J)

1.0 5.02 50

VIN=8V
lO=0A
0.8 40
Dropout Voltage VDIF (V)

Ground Current IG (mA)

Output Voltage VO (V)
0.6 30

5.00
0.4 20

lO=2A
1.5A
0.2 10
1A
0.5A
0A
0 4.98 0
0 0.5 1 1.5 2 –40 –20 0 20 40 60 80 100 120 140 0 5 10 15
Output Current IO (A) Ambient Temperature Ta (°C) Input Voltage VIN (V)

Quiescent Circuit Current(SI-3050J) Rise Characteristics(SI-3050J) Rise Characteristics(SI-3120J)

0.5 6 14
Quiescent Circuit Current Iqoff (mA)

5 12
0.4
Output Voltage VO (V)

Output Voltage VO (V)

10
4
VC=0V lO=0A
0.3 lO=0A
0.5A 8
0.5A
3 1A
1A
1.5A 6
0.2 1.5A
2A
2 2A
4
0.1
1
2

0 0 0
0 5 10 15 0 1 2 3 4 5 6 7 8 0 5 10 15 20
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)

Overcurrent Protection Characteristics(SI-3050J) Overcurrent Protection Characteristics(SI-3120J)

6 14

5 12
22V 3V
25V
27V
8V

12V
Output Voltage VO (V)

Output Voltage VO (V)

10V 10
4
15V
6V
15V

8
V

3
18

6
2
4

1
2

0 0
0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 4.0
Output Current IO (A) Output Current IO (A)

ON/OFF Control Characteristics(SI-3050J) Thermal Protection(CharacteristicsSI-3050J)

6 6
VIN=8V VIN=8V
lO=10mA lO=10mA
5 5
Output Voltage VO (V)

Output Voltage VO (V)

4 4

3 3

2 2

1 1
Note on Thermal Protection:
The thermal protection circuit is intended for pro-
0 tection against heat during instantaneous short-
0 1.0 2.0 3.0 4.0 5.0 0
0 20 60 100 140 180
Output ON/OFF Control Voltage VC (V) circuiting. Its operation is not guaranteed for short-
Case Temperature TC (°C)
circuiting over extended periods of time.

51