厦门四信通信科技有限公司

Xiamen Four-Faith Communication Technology Co., Ltd.

Virtual Serial Port Software(TCP2COM) Manual

TCP2COM software can used to transfer data which receive from IP Modem to a specified
virtual serial port,and it can also transfer data which send by virtual port to IP Modem.

Here is the Manual:

“Four-Faith TCP2COM V2.4”

Open“ ”software

If it shows as below,please check current software path exist Info.mdb,if exists that means there is something

wrong with Info.mdb,Please open Info.mdb by using Access ,and choose menu “Tools”->” Database practical tools”->”

Compression and repair the database” of the Access to repair it.

1.Before
1.Before using virtual serial port, you must install the dri driver
river of virtual serial
port by steps :
Click Menu “Operation”,choose the item “Add virtual port”,it will pop up the dialog
which you can set the virtual serial port number ,then click OK to install the driver.
Then the PC will install device driver,and show whether the driver has installed success as below.

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 1
网址：http://www.four-faith.com
 厦门四信通信科技有限公司
Xiamen Four-Faith Communication Technology Co., Ltd.

2. click button or click “window

window”-----“Tunnel
window Tunnel Manager”as
Manager as below：
below：

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 2
网址：http://www.four-faith.com
 厦门四信通信科技有限公司
Xiamen Four-Faith Communication Technology Co., Ltd.

Click “Add Tunnel”,Set the params according to the serial port property.

Note：Set the transfer tunnel parameters at this interface，the setting as above set
the Device ID of IP Modem as 74736525,and set the data transfer to COM1,and the data
from COM1 will also be transfered to IP Modem which ID is 74736525.
When finishing setting transfer parameters,click “Save” ,it will show whether the add
tunnel operation is success.

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 3
网址：http://www.four-faith.com
 厦门四信通信科技有限公司
Xiamen Four-Faith Communication Technology Co., Ltd.

If add tunnel success,it will show transfer parameters on Tunnel Manger interface as
below：

Note：A、Different ID of IP Modem can transfer to one same serial port,but it can not
transfer one ID of IP Modem to multiple serial ports.
B、Tunnel Manger can also Modify and Delete the exist tunnel.Current version support
5000 tunnels at most.

3.Setting
.Setting the server parameter
parameters.
eters.

Click Menu “Setting” item or click button to open setting dialog：

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 4
网址：http://www.four-faith.com
 厦门四信通信科技有限公司
Xiamen Four-Faith Communication Technology Co., Ltd.

The setting as above set the server listen port as 5001,and set online detect time
interval as 32 sec(current system time minus lastest time to receive data ,if the
value big than 32,the software will show this IP Modem has disconnected)

“Tunnel Manager” and “Setting” parameters are saved to database,so the next time to
open the software ,you don’t need to reset the parameters.
Setting as below:

4.Server connection state

After setting the parameters of tunnel and server,click menu “Operation”->”Start service”

or just press button ，the software will start to listening and waiting the
connection from IP Modem.
Here is the state of id of 74736574 IP Modem not connected .

After starting service it will show the detail information of all tunnels .
Here is the state of ID 74736525 IP Modem connected

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 5
网址：http://www.four-faith.com
 厦门四信通信科技有限公司
Xiamen Four-Faith Communication Technology Co., Ltd.

When connection establish success ,the list will show the Phone No,Source IP,Inbound
flow and Outbound flow as above.

Click to stop service.

5.Monitor

Click Menu “Window”->”Monitor Window”,or press button ，it will show the monitor
window which can show outbound and inbound data as below.if you want to monitor one
tunnel ,just click the left tree id,it will show the selected id data.

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 6
网址：http://www.four-faith.com
 厦门四信通信科技有限公司
Xiamen Four-Faith Communication Technology Co., Ltd.

6.Not transmited
transmited data query.

Click menu “Database”->”Query Not Transmited Data”,or press button ，you can
query the data which receive from IP Modem but transfer to serial port failed as below ，
Also you can just open the database file “Info.mdb”(Access Database file),find table
“NotTransData” to query the data.

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 7
网址：http://www.four-faith.com
 厦门四信通信科技有限公司
Xiamen Four-Faith Communication Technology Co., Ltd.

7.Delete database data

Click menu “Database”->”Delete saved data”,or press button ，you can delete the
data by device ID,also you can delete all of the data in database ,the dialog as below

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 8
网址：http://www.four-faith.com
 厦门四信通信科技有限公司
Xiamen Four-Faith Communication Technology Co., Ltd.

8：Quit

Click menu “Operation”->”Exit”,or press button ,it will show as below

Press OK to quit TCP2COM.

Any questions ,please contact our technical department .

地址：厦门市软件园观日路 44 号 3 楼 J1-J2 9
网址：http://www.four-faith.com