MODEL 711 - INCREMENTAL SHAFT ENCODER

F E AT U R E S
The Original Industry-Standard Cube
Five VersaƟle Housing Styles
UnidirecƟonal Output
ResoluƟons Available to 10,000 CPR
The Model 711 Accu-Coder™ is the original, industry standard cube encoder.
Designed for compatibility with most programmable controllers, electronic
counters, motion controllers, and motor drives, it is ideally suited for
applications that require a simple, symmetrical, unidirectional square wave
output in a single channel format. Critical performance specifications for the
most popular resolutions and advanced Opto-ASIC circuitry—a single chip
design that eliminates many board level components— increases the reliability
of an already dependable and durable encoder. With new options continually
being added, the Model 711 excels in a wide variety of industrial applications.
C O M M O N A P P L I C AT I O N S
Feedback for Counters, PLCs & Motors, Measuring For Packaging,
Filling & Material Handling Machines, Wire Winding, Film Extrusion

M O D E L 711 O R D E R I N G G U I D E
Blue type indicates price adder options. Not all configuration combinations may be available. Contact Customer Service for details.

711 0256 S HD1 6 S S N

MODEL OUTPUT TYPE SHAFT DIAMETER 3 MATING

711 Unidirectional Cube S Pull-Up Resistor 4 1/4", 0.250" 4 CONNECTOR
(Single Channel) O Open Collector 5 5/16", 0.3125" 5 N No Connector
PP Push-Pull 6 3/8", 0.375" Y Yes
HV Line Driver 8 1/2", 0.500" 6
CYCLES PER REVOLUTION (CPR)
10 5/8", 0.625" 6 CONNECTOR TYPE 8
1-10,000
See CPR Options below for available S Standard 6-pin MS
resolutions. HOUSING TYPE SHAFT TYPE Y 7-pin MS
(1271 and above is a price adder) S 2.25" Standard Housing S Single J 5-pin M12 (12 mm) 7
S1 2.25" Standard Housing with IP50 Felt D Double ended 7 K 8-pin M12 (12 mm) 7
Shaft Seal 1 G Gland Nut - 18" Cable 9
IND12 Industrial Housing with IP65 Shaft Seal T Solder or Screw Terminal 10
HD1 3" x 3" x 6" Heavy Duty Housing B Solder Terminal with Conduit Box
HD3 Heavy Duty Housing with
Conduit Connector & Terminal Strip
HD5 Heavy Duty Housing with 10 mm Outer
Bearing
HD10 Heavy Duty Housing with Ultra Heavy
Duty Bearings, 0.625" or 0.500" Shaft
HD12 Heavy Duty Housing with IP65 Outer
Shaft Seal
HD14 Heavy Duty Housing with IP65 Shaft Seal
and with Conduit Connector & Terminal
Strip
5PY Standard Cube With 5PY Adaptor 2
EX Explosion-proof Housing

NOTES:
M O D E L 711 C P R O P T I O N S 1 Available with 0.250" shaft only.
0001 thru 0189* 0193 0198 0200 0205 0210 0240 2 Only available with 5/16" (0.3125") shaft.
0250 0256 0276 0298 0300 0305 0308 0315 0333 3 Contact Customer Service for custom shaft lengths and diameters.
0336 0350 0360 0400 0480 0500 0512 0580 0597 4 Standard housing only.
5 Standard or 5PY housing only.
0600 0700 0720 0800 0840 0960 1000 1024 1200 6 HD10 housing only.
1250 1270 1500 1800* 2000 2048 2500 3000 3600* 7 Not available for HD or EX housings.
4096 5000 6000 7200* 8192 10,000 8 For mating connectors, cables, and cordsets see Encoder Accessories
*Contact Customer Service for availability. on page 102 or visit Encoder website. For Pin Configuration
Diagrams, see page 107 or visit Encoder website.
Contact Customer Service for other disk resolutions. Not all disk resolutions 9 For non-standard cable lengths, add a forward slash (/) plus cable
available with all output types. length expressed in feet. Example: G/6 = 6 feet of cable.
For CPR > 2500. Standard cable length only.
10 Screw terminals available for HD and EX housings. Solder terminals
available for S and S1 housings.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

M O D E L 711 S P E C I F I C AT I O N S
Common to all cube housing styles.
Electrical Max Frequency ........1 to 2500 CPR 125 kHz Bearings....................Precision ABEC ball bearings
Input Voltage............4.75 to 28 VDC max for temperatures 2501 to 5000 CPR 250 kHz
5001 to 10,000 CPR 500 kHz
Environmental
up to 85° C
Storage Temp ...........-25° to +85° C
4.75 to 24 VDC for temperatures Symmetry .................180° (±18°) electrical
Humidity...................98% RH non-condensing
between 85° C and 100° C. Rise Time ..................Less than 1 microsecond
Vibration...................10 g @ 58 to 500 Hz
Input Current ............ 80 mA maximum with no output load Accuracy .......................Within 0.05° mechanical from one cycle
Shock ........................50 g @ 11 ms duration
Input Ripple..............100 mV peak-to-peak at 0 to 100 kHz to any other cycle, or 3 arc minutes.
Output Format .........Incremental- Square wave with
Mechanical
single channel
Max Speed ............... 6000 RPM. Higher shaft speeds
Output Types..................Open Collector- 250 mA max per channel
achievable, contact Customer Service.
Pull-Up- 250 mA max per channel
Shaft Material ..........303 Stainless Steel
Push-Pull- 20 mA max per channel
Housing ....................Black non-corrosive finished 6063-T6
Line Driver- 20 mA max per channel
aluminum
(Meets RS 422 at 5 VDC supply)

W I R I N G TA B L E
7-pin 6-pin 6-pin Term. Term.
S TA N DA R D C U B E H O U S I N G Gland 7 pin MS MS MS Block Block
Cable† 5-pin 8-pin 10-pin MS O,S HV, O,S HV, O,S
ΈS, S1Ή S P E C I F I C AT I O N S Function Wire Color M12 M12 MS HV PP No Index PP No Index HV,PP
Mechanical Com Black 3 7 F F F A A,F 1 1,6
Shaft Type ................Single or double-ended (specify choice)
Radial Loading ..........15 lb maximum (0.250" diameter shaft) +VDC Red 1 2 D D D B B 2 2
40 lb maximum (0.375" diameter shaft)
Axial Loading ............10 lb maximum (0.250" diameter shaft) A White 4 1 A A A C D 3 4
30 lb maximum (0.375" diameter shaft) A' Brown -- 3 H C -- D -- 4 --
Starting Torque ........0.13 oz-in typical for 0.250" shaft
0.38 oz-in typical for 0.375" shaft Case -- -- -- G G G -- -- -- --
Moment of Inertia ...6.5 x 10-6 oz-in-sec2
Shield Bare -- -- -- -- -- -- -- -- --
Weight ......................10 oz for standard housing
†Standard cable is 24 AWG conductors with foil and braid shield.

WAV E F O R M D I A G R A M

S TA N DA R D C U B E H O U S I N G ΈS, S1Ή C U B E P I VOT M O U N T I N G B R A C K E T S

176430-01 Single Pivot
Cube Housing With 1/4" Shaft (4) Cube Housing With 3/8" Shaft (6) 176431-01 Double Pivot
176430-02 Spring Loaded Single Pivot
176431-02 Spring Loaded Double Pivot
Encoder sold separately.

Dual Wheel Single Wheel

(shown with Torsion Spring)

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

CUBE HOUSINGS
I N D U S T R I A L C U B E H O U S I N G ΈI N D12Ή
This more robust unit meets requirements between Standard and Heavy Duty housings while retaining the Cube design. The Industrial 12 (IND12)
model features an IP65 shaft seal. The tough, sealed aluminum housing has a wall thickness of 0.187" and offers greater protection from wash
down, sprays, dust, moisture, shock, vibration, and other hazards found in industrial environments.

INDUSTRIAL CUBE HOUSING

ΈI N D12Ή S P E C I F I C AT I O N S
Refer to all Standard Cube Housing specifications
except as follows:

Mechanical
Shaft Size ..................0.375" diameter
Shaft Type ................Single- or Double-Ended Shaft Available
Radial Loading ..........40 lb Maximum
Axial Loading ............30 lb Maximum
Starting Torque ........ 3 oz-in Starting Torque w/IP65 Shaft Seal
All dimensions are in inches with a tolerance of +0.005" or +0.01" unless otherwise specified

H E AV Y D U T Y C U B E H O U S I N G ΈH D12Ή
H E AV Y D U T Y C U B E H O U S I N G
The Heavy Duty housing uses a separate 0.375" diameter external shaft and bearing assembly
to rotate the shaft of an internally mounted Cube Housing. This provides mechanical isolation
ΈH D12Ή S P E C I F I C AT I O N S
from external loads and stress. A flexible coupling between the external shaft and the Refer to all cube specifications except as follows:
encoder protects the internal unit from axial and radial loading. The 0.250" aluminum walls Mechanical
protect the encoder from external shock, vibration, and the outside environment. Max Speed ...............6000 RPM
Shaft Size ..................0.375"
Heavy Duty Housing OpƟons Rotation....................Either direction
HD 1 Heavy Duty 3" x 6" housing Radial Loading ..........40 lb maximum (50 lb for HD 5)
HD 3 Heavy Duty w/conduit connector (threaded for 0.500" NPT Conduit) and terminal strip Axial Loading ............30 lb maximum (35 lb for HD 5)
HD 5 Heavy Duty w/10 mm outer bearing Bearings....................Precision ABEC ball bearings
Starting Torque ........1 oz-in; 3 oz-in w/IP65 seal
HD 12* Heavy Duty w/IP65 rated outer shaft seal
Mounting .................Tapped holes face and base
HD 14* Heavy Duty w/IP65 rated outer shaft seal, conduit connector Weight ......................3.25 lb
(threaded for 0.500" NPT Conduit), and terminal strip
*These units have an outer boss diameter of 1.000"

U LT R A H E AV Y D U T Y
C U B E H O U S I N G ΈH D 10Ή
S P E C I F I C AT I O N S
U LT R A H E AV Y D U T Y C U B E H O U S I N G ΈH D10Ή
Mechanical
The HD 10 Ultra Heavy Duty encoder is designed for use in applications with severe shaft Max Speed ...............6000 RPM
loading conditions. The HD 10 offers two shaft sizes: 0.500" and 0.625". Shaft material is Shaft Size ..................0.500" or 0.625"
303 stainless steel. Bearings are conservatively rated at 95 lb radial and 60 lb axial shaft Rotation....................Either direction
loading. IP65 shaft seal is standard on all units. The HD 10 Ultra Heavy Duty housing uses a Radial Loading ..........95 lb operating
larger external shaft and R10 bearing assembly to rotate the shaft of an internally mounted Axial Loading ............60 lb operating
Cube Housing. This provides mechanical isolation from external loads and stress. A flexible Bearings....................ABEC precision ball bearings
coupling between the external shaft and the encoder protects the internal unit from axial Bearing Life ..............15,000 hours at rated load
Starting Torque ........3 oz-in IP65 rated
and radial loading. The 0.250" aluminum walls protect the encoder from external shock,
Mounting .................Tapped holes face and base
vibration, and the outside environment. Weight ......................3.85 lb

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

U LT R A H E AV Y D U T Y C U B E H O U S I N G ΈH D10ΉͷC O N T'D

All dimensions are in inches with a tolerance of +0.005” or +0.01” unless otherwise specified

E X P L O S I O Nͳ P R O O F H O U S I N G ΈE XΉ
An explosion-proof housing is available for installing the Cube Series Accu-Coder™ in hazardous E X P L O S I O Nͳ P R O O F
locations. The Cube Series encoder is mounted within the explosion-proof housing and is H O U S I N G ΈE XΉ
coupled to the 0.375" shaft assembly by a flexible shaft coupling. This decreases radial and axial
loading on the internal encoder shaft and bearings to ensure long life. Electrical connection to S P E C I F I C AT I O N S
The explosion-proof housing is designed to meet the
the Accu-Coder™ is by an internal barrier terminal strip. A threaded hole for 0.500" NPT conduit following:
is provided. NEC Class 1, Groups C and D
NEC Class 2, Groups E, F, and G
UL Standard 1203
Class 1, Division 1, Groups C and D
Class 2, Division 1, Groups E, F, and G
CSA Standard C 22.2 No. 30-M 1986
NEMA 7 and NEMA 9
Refer to all cube specifications except as follows:
Mechanical
Max Speed ...............4000 RPM
Radial Loading ..........30 lb operating
Axial Loading ............10 lb operating
Weight ......................6 lb
Finish ........................Unpainted Aluminum

C U B E S E R I E S O P T I O N A L 5P Y A DA P T E R Έ175443Ή
The all aluminum optional 5PY adapter allows any standard housing Cube Series encoder to replace
DC tachometer technology. The 5PY adapter is interchangeable with any 5PY tach generator.

Order standard housing Cube Series

Accu-Coder™ with 5/16” shaft and
specify part #175443.

All dimensions are in inches with a tolerance of +0.005” or +0.01” unless otherwise specified.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]