Performance Assessment – Review – Help Sheet

This guide is provided to assist you with the tasks in the Performance Assessment-Review. Use this guide
to help you with the Performance Assessment when you get stuck with creating your network. You can
also use this if you need help with the entire performance assessment.

Task 1 – Setting up the network

This will be your number throughout the term and will not change.
Your network is:

10.25.0.0/16

You will notice that everything shows up with red lights and that is okay. Nothing will turn
green until you have programmed the routers.

These are all the devices we will work with in this assessment.
Ther are a total of four 2960 switches, 12 PCs, and four servers. The four servers are named:
RADIUS, BIS_Server, SLC_Server, and THCA_Server.
 1. Let’s Configure Switch0 to Sw1.
Make sure you change the hostname to Sw1.
Would you like to enter the initial configuration dialog? [yes/no]:
no
Switch>enable
Switch#configure terminal
Switch(config)#hostname Sw1
Sw1(config)#interface range f0/1-5
Sw1(config-if-range)#switchport mode access
Sw1(config-if-range)#switchport access vlan 10
Sw1(config)#interface range f0/6-10
Sw1(config-if-range)#switchport mode access
Sw1(config-if-range)#switchport access vlan 20
Sw1(config)#interface range f0/11-15
Sw1(config-if-range)#switchport mode access
Sw1(config-if-range)#switchport access vlan 30
Sw1(config)#interface range f0/16-20
Sw1(config-if-range)#switchport mode access
Sw1(config-if-range)#switchport access vlan 40
Sw1(config-if-range)# interface range g0/1-2
Sw1(config-if-range)# switchport mode trunk

2. Now setup and program Sw2-4 the same way you did Sw1. Make sure you create the
correct hostname on the switches accordingly.
You will notice that the switches, PCs, and server all turned green meaning they are ready. This
is because no programming is required for these systems to work on the network.
3. Router Configuration
Now you will need to go in and program each of the routers.
Click on the R1 router and go to the CLI tab. This is the command line interface which you will
be using to program your routers.

You may need to type the enter key a couple of time to wake the system up.
You will now see the router prompt for the system

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no

Type the command enable in order to enter privileged mode. You can tell you are in privileged
mode because the prompt turned to a # symbol.

Type the command configure terminal and then hostname with the name of the router (R1)
You will notice the prompt will change to the name you have given your system. This is
important so you can keep your systems straight as you are programming them.

Now you will go through each of your routers and program the information for each interface.
Syste Connect
Port IP address Subnet Mask Clock Rate
m To
R1 G0/0/1 Internet 11.0.0.25 255.255.255.0
255.255.255.25
Se0/1/0 R2 10.25.5.1 500000
2
255.255.255.25
SE0/1/1 R3 10.25.5.10
2

R1(config)# interface g0/0/1

R1(config-if)# ip address 11.0.0.25 255.255.255.0
R1(config-if)# no shutdown
R1(config)# interface s0/1/0
R1(config-if)# ip add 10.25.5.1 255.255.255.252
R1(config-if)# clock rate 500000
R1(config-if)# no shutdown
R1(config-if)# interface s0/1/1
R1(config-if)#ip add 10.25.5.10 255.255.255.252
R1(config-if)#no shutdown

Syste Connect
Port IP address Subnet Mask Clock Rate
m To

G0/0/0.1 255.255.255.19
R2 Sw4 10.25.2.1 BIS Server
0 2

G0/0/0.2 255.255.255.19
Sw4 10.25.2.65 SLC Server
0 2

G0/0/0.3 10.25.2.12 255.255.255.19 THCA

Sw4
0 9 2 Server

G0/0/0.4 Sw4 10.25.2.19 255.255.255.19 RADIUS

 0 3 2 Server

255.255.255.25
Se0/1/0 R3 10.25.5.5 500000
2

255.255.255.25
SE0/1/1 R1 10.25.5.2
2

Use the table above to configure R2. You will need to get into global configuration mode
first like you did already for R1.

R2(config)# int g0/0/0

R2(config-if)# no shutdown
R2(config-if)# int g0/0/0.10
R2(config-subif)# enc dot1q 10
R2(config-subif)# ip add 10.25.2.1 255.255.255.192
R2(config-subif)# int g0/0/0.20
R2(config-subif)# enc dot1q 20
R2(config-subif)# ip add 10.25.2.65 255.255.255.192
R2(config-subif)# int g0/0/0.30
R2(config-subif)# enc dot1q 30
R2(config-subif)# ip add 10.25.2.129 255.255.255.192
R2(config-subif)# int g0/0/0.40
R2(config-subif)# enc dot1q 40
R2(config-subif)# ip add 10.25.2.193 255.255.255.192
R2(config-subif)# int s0/1/0
R2(config-if)# ip add 10.25.5.5 255.255.255.252
R2(config-if)# clock rate 500000
R2(config-if)# no shutdown
R2(config-subif)# int s0/1/1
R2(config-if)# ip add 10.25.5.2 255.255.255.252
R2(config-if)# no shutdown

Connect
System Port IP address Subnet Mask
To
R3
BIS- 28
G0/0/0.10 Sw1 10.25.3.1 255.255.255.224
Users
G0/0/0.20 Sw1 10.25.3.33 255.255.255.240 SLC- 14
 Users
THCA-10
G0/0/0.30 Sw1 10.25.3.49 255.255.255.240
Users
G0/0/0.40 Sw1 10.25.3.65 255.255.255.248 5 Users
500000 –
Se0/0/0 R1 10.25.5.9 255.255.255.252
Clock Rate
SE0/0/1 R2 10.25.5.6 255.255.255.252

R3(config)# int g0/0/0

R3(config-if)# no shutdown
R3(config-if)# int g0/0/0.10
R3(config-subif)# enc dot1q 10
R3(config-subif)# ip add 10.25.3.1 255.255.255.224
R3(config-subif)# int g0/0/0.20
R3(config-subif)# enc dot1q 20
R3(config-subif)# ip add 10.25.3.33 255.255.255.240
R3(config-subif)# int g0/0/0.30
R3(config-subif)# enc dot1q 30
R3(config-subif)# ip add 10.25.3.49 255.255.255.240
R3(config-subif)# int g0/0/0.40
R3(config-subif)# enc dot1q 40
R3(config-subif)# ip add 10.25.3.65 255.255.255.248
R3(config-subif)# int s0/1/0
R3(config-if)# ip add 10.25.5.9 255.255.255.252
R3(config-if)# clock rate 500000
R3(config-if)# no shutdown
R3(config-subif)# int s0/1/1
R3(config-if)# ip add 10.25.5.6 255.255.255.252
R3(config-if)# no shutdown

Now set up your OSPF routing protocol on each router.

R1(config)# router OSPF 1
R1(config-router)# network 10.25.5.0 0.0.0.3 area 0
R1(config-router)# network 10.25.5.8 0.0.0.3 area 0
R1(config-router)# network 11.0.0.0 0.0.0.255 area 0
For R2 and R3

R2(config)# router OSPF 1

R2(config-router)# network 10.25.5.0 0.0.0.3 area 0
R2(config-router)# network 10.25.5.4 0.0.0.3 area 0
R2(config-router)# network 10.25.2.0 0.0.0.63 area 1
 R2(config-router)# network 10.25.2.64 0.0.0.63 area 1
R2(config-router)# network 10.25.2.128 0.0.0.63 area 1
R2(config-router)# network 10.25.2.192 0.0.0.63 area 1

R3(config)# router OSPF 1

R3(config-router)# network 10.25.5.4 0.0.0.3 area 0
R3(config-router)# network 10.25.5.8 0.0.0.3 area 0
R3(config-router)# network 10.25.3.0 0.0.0.31 area 1
R3(config-router)# network 10.25.3.32 0.0.0.15 area 1
R3(config-router)# network 10.25.3.48 0.0.0.15 area 1
R3(config-router)# network 10.25.3.64 0.0.0.7 area 1

Verify that your network is set up correctly by typing.

R1# show ip route

Verify that you can ping from one router to another by typing the following on R1
R1# ping 10.25.5.9

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.25.5.5, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/5/21 ms

4. Setting up DHCP on your server

There are two methods assigning IP addresses on a network- assigning static IP addresses and
DHCP addresses. In this task you will be programming a server to assign IP addresses using
DCHP.
First we need to configure our servers with static addresses.
a. Configuring a static address on the servers.
Open your servers and go to the Desktop tab and click on the IP configuration square.
Type in the following IP address information.
BIS Server-
IP Address- 10.25.2.2
Subnet Mask- 255.255.255.192
Default Gateway- 10.25.2.1

SLC Server-
IP Address- 10.25.2.66
Subnet Mask- 255.255.255.192
Default Gateway- 10.25.2.65

THCA Server-
IP Address- 10.25.2.130
Subnet Mask- 255.255.255.192
Default Gateway- 10.25.2.129

RADIUS Server-
IP Address- 10.25.2.194
Subnet Mask- 255.255.255.192
Default Gateway- 10.25.2.193

The reason you give a static IP address to your servers is so other systems can refer to them
using this address and it will never change.
 b. Creating DHCP Pools on Server
Now you will set up the DCHP pools for your PCs and laptops.
i. In your RADIUS Server select the Services tab and select the DHCP
service.

ii. Turn the service on

You will see that you already have one address pool assigned that will be for your server
network.
iii. Change the serverPool information to the following:
Default Gateway: 10.25.2.1
DNS server: 10.25.2.10
Start IP address 10.25.2.11
Subnet Mask: 255.255.255.192
TFTP server: 10.25.2.10

iv. Press the save button to update the DHCP pool. You will see the
serverPool parameters change to the new information.

v. Go back to the information at the top and change it to

Pool Name: 10
Default Gateway: 10.25.3.1
DNS server: 10.25.2.10
Start IP address 10.25.3.2
Subnet Mask: 255.255.255.224
TFTP server: 10.25.2.10
 i. Press the Add button to create the new DHCP pool. You should now see
the new pool on top of the DHCP pools on your server.
ii. Go in and add the 20, 30, and 40 pools below.
Pool Name: 20
Default Gateway: 10.25.3.33
DNS server: 10.25.2.10
Start IP address 10.25.3.34
Subnet Mask: 255.255.255.240
TFTP server: 10.25.2.10

Pool Name: 30
Default Gateway: 10.25.3.49
DNS server: 10.25.2.10
Start IP address 10.25.3.50
Subnet Mask: 255.255.255.240
TFTP server: 10.25.2.10

Pool Name: 40
Default Gateway: 10.25.3.65
DNS server: 10.25.2.10
Start IP address 10.25.3.66
Subnet Mask: 255.255.255.248
TFTP server: 10.25.2.10
 i. Update R3 router

Only one other thing to do is to add a helper addresses into the R3 router.
R3(config)# interface G0/0/0.10
R3(config-int)# ip helper-address 10.25.2.194
R3(config)# interface G0/0/0.20
R3(config-int)# ip helper-address 10.25.2.194
R3(config)# interface G0/0/0.30
R3(config-int)# ip helper-address 10.25.2.194
R3(config)# interface G0/0/0.40
R3(config-int)# ip helper-address 10.25.2.194

You should now be able to go into your PCs, desktop tab and select IP configuration.

Change your IP configuration to DHCP. Your PCs should now be able to pull a DHCP address
from your server.
If it doesn’t work check to make sure you can ping the server for your R2 router. If you can
there is another problem you will need to troubleshoot.

Troubleshooting your DHCP problems can be difficult. So, you need to sectionalize the problem.
 First check to make sure your pools on your server is correct. If any of your addresses
are incorrect it will not work.
 Next check to make sure your helper-address on your router is correct. You can do this
by typing show run on your router and checking your G0/0 interface. It should show the
IP address of your server.
 Lastly, check to see if your DHCP service is turned on. By default, the service is off and
you must turn the service on for it to work.
Check your system by pinging from PC2 to your server.

Task 2 – Connecting to the Tier1 Network

You will be using the Multiuser link to connect your corporate office through
the Internet. First, make sure you have the multiuser connection on your
packet tracer network. This icon looks like a cloud with three lines in it (not
the cloud without them).

Go to Extensions at the drop-down menu and select multiuser and Listen.

Remove the password (if any) and select always accept to both existing and
remote networks.

Now click through Extensions and Port visibility

Select your ports of G0/0/0 and G0/0/1 on the R1 router and the G0/0/1 on
the R3 router. These are the ports that will be available for connection to
external users.
Open you Tier1Network and verify that you have the following network

You should now have two networks open on your screen at the same time
Verify the port number of your Tier1 Network by looking at the listen page of
the multiuser dropdown menu. Write your port number below.

Port number ______________________________________________________

Click on the Multiuser cloud and type localhost and Peer port number for
your tier1 network. You should use the Peer name of Peer20 on your
connection.

Click the connect button. You should now see the Peer connection cloud
appear on the packet tracer screen as green or blue.
Wait for the connection to turn green on both sides. If the connect stays red
you may need to disconnect and reconnect the cable going to the cloud.
Select the link at the top of the cloud, not create a new link so you can
connect to the system on the other side of the link.

Now you are going to connect from your network into the Internet network using the multiuser cloud.

Click on your multiuser cloud and select outgoing connection. Add the Peer address of localhost, the
peer port number of 38001 (it may be 38000) and the peer network name of Peer20.

Click the connect button

A connection should now appear between your two packet tracer desktops. The cloud may initially turn
green to indicate a new connection but will soon turn to blue.

You may also need to disconnect and reconnect the cable going to your cloud if it doesn’t turn green
reconnect with the link at the top (Link 0) not with create new link

The connection should now turn green to your router.

Check your connection to the Tier1 Network by going to R1 and pulling show
ip route.

Ping the Tier1 Network server with one of your PCs. It is okay if you get a timeout
(or even two) to start the process.