Scribd
Upload
31 views2 pages

Tpu Soft

TPU 'SOFT' is a thermoplastic polyurethane elastomer known for its transparency, mechanical properties, heat resistance, and flexibility at low temperatures, suitable for high-end applications like wires, cables, and conveyor belts. It features specific properties such as a Shore A hardness of 70, tensile stress of 30 MPa, and an ultimate elongation of 550%. The document also provides processing guidelines for injection molding and extrusion, emphasizing the importance of drying and cleaning before processing.

Uploaded by

sima.moldes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
31 views2 pages

Tpu Soft

TPU 'SOFT' is a thermoplastic polyurethane elastomer known for its transparency, mechanical properties, heat resistance, and flexibility at low temperatures, suitable for high-end applications like wires, cables, and conveyor belts. It features specific properties such as a Shore A hardness of 70, tensile stress of 30 MPa, and an ultimate elongation of 550%. The document also provides processing guidelines for injection molding and extrusion, emphasizing the importance of drying and cleaning before processing.

Uploaded by

sima.moldes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

TPU “SOFT”

TECHNICAL DATA SHEET

Product Feature：

“SOFT” is a thermoplastic polyurethane elastomer. It has good transparency, good mechanical properties, Good heat
resistance, humidity resistance, and excellent flexibility under very low temperature. It is both an injection and extrusion
molding grade for high-end products.

Applications:

Wire & cable, high pressure oil tubes, conveyor belts, shoes, seals, screen packs, etc.

Product Propert:

Typical Properties Test Method Unit Typical values*


Form N/A - Pellet
Color N/A - Transparent
Hardness ASTM D-2240 Shore A 70
Gravity ASTM D-792 g/cm3 1.18
100% Modulus of elasticity ASTM D412 MPa 5
Tensile Stress ASTM D-412 MPa 30
Tear Strength ASTM D-624 N/mm 100
Ultimate Elongation ASTM D-412 % 550
DIN Abrasion ISO 4649 mm3 60
Yellow Index ASTM E313 -- 7

*All these physical properties are based on injection molded samples, which are conditioned at 23 ºC/50% for
24h.Above values are typical values and should not be used as specifications.

Comercializadora Berintrex SA de CV Dirección: Fidel Velazquez # 414, Col. Valle de León, León Guanajuato 37140
TPU “SOFT”
TECHNICAL DATA SHEET
Processing Guidelines：

Injection Moulding Guideline

Mold Shrinkage: 0.015 ～ 0.025 inch/inch


Injection Speed: Medium-Fast
Injection Pressure: Medium-Fast
Back Pressure: Low-Medium
Holding Pressure Sufficient to pack the mould
Cooling: Can be demoulded when
part have sufficiently cooled
Barrel Temperature (℃) 150-160 170-180 180-190 190-210 25-4

Extrusion Guidelines:

L/D Ration: 20:1 – 25:1


Compression Ratio: 2.5 – 3.0
Breaker Both should be used
Plate/Screen:
Draw Down: 5 – 10%
Cooling Cold wáter bath

Barrel Temperature (℃) 150-170 200-210 210-230 200-235 180-200

Processing Notes:

A、Drying before processing, it is recommended to dry for 3-5 hours at 80 degrees centigrade. If it is damp, the drying
time will be lengthened.

B、Cleaning the screw and die with PP or PE before and after processing.

C、The gate and runner can be recycled, but less than 15%.

D、PE/EVA base color masterbatch is better for coloring.

The information and suggestions contained in this bulletin are to the best of our knowledge, accurate and reliable, but no gu arantee of their accuracy is made. All products are sold upon
condition that purchasers shall make their own tests to determine the suitability of such products for their particular purposes and uses and purchasers assume all risks and liability for the
results of use of the products, including use in accordance with seller’s suggestions. Nothing in this bulletin constitutes permission or a recommendation to practice or use any invention
covered by any patent owned by this company or by others. There is no warranty of merchantability and there are no other warranties for the products described

Comercializadora Berintrex SA de CV Dirección: Fidel Velazquez # 414, Col. Valle de León, León Guanajuato 37140

You might also like