28/03/2025 19:33 class QciProfileOperatorDefined

Managed Object Model 163/155 54-LZA 701 6014/3-V1 Uen FM

class QciProfileOperatorDefined
ManagedElement
ENodeBFunction
QciTable
QciProfileOperatorDefined

Contains bearer-level QoS configuration. Instances of this class are created on demand by the operator. Each QciProfileOperatorDefined instance corresponds to a unique operator
defined QCI number within the range 10-255. The instances can be created and configured independent of the serviceStateOperatorDefinedQci. However the configured QCI profiles
can not be used at bearer setup / modify unless the service state is OPERABLE.

References to:
DrxProfile; LogicalChannelGroup; ManagedObject; RlfProfile; TimerProfile;

Attributes
AbsPrioOverride absPrioOverride = NO_OVERRIDE
Indicates if the data radio bearer is subject to Absolute Priority Override.

Dependencies: Only relevant if the license for QoS Aware Scheduler is present and the feature is active.
Disturbances: Changing this attribute can cause loss of traffic.
Takes effect: New connection
AQMMode aqmMode = OFF
Active Queue Management (AQM) mode

Takes effect: Cell lock/unlock

boolean bitRateRecommendationEnabled = false
Enables bit rate recommendation for QCI.

Dependencies: Only relevant if license for VoLTE Rate Recommendation is present and feature is active.
Takes effect: New connection
boolean counterActiveMode = false
Defines the interpretation of active for the QCI:
FALSE (DEFAULT):
Active time is measured in the case of:
DRB: as the time when there is data in a buffer, DL and/or UL, with an added guard period of 100 ms thereafter
UE: as the time when there is data in a buffer, DL and/or UL, with an added guard period of 100 ms thereafter in any of the DRBs connected to the UE
The pmCounters for active E-RABs are stepped in case of data in a buffer, DL and/or UL.
TRUE:
Active time is measured in the case of:

about:blank 1/10
28/03/2025 19:33 class QciProfileOperatorDefined
DRB: from the first data occurrence in a buffer to the last data occurrence in a buffer for that DRB
UE: from the first data occurrence in a buffer to the last data occurrence in a buffer for any DRB associated with the UE
The pmCounters for active E-RABs are always stepped since the DRB is considered always active

Takes effect: Cell lock/unlock

boolean dataFwdPerQciEnabled = false
Enables forwarding of data for this QCI. However, forwarding of DL data for SN terminated bearers in EN-DC setup is always enabled and is not
controlled by this attribute.

Dependencies: The parameter is only valid if the IntraLTEHODataFwd or S1HODataFwd licence is installed and active.
long dlMaxHARQTxQci = 5 { 1, 2, 3, 4, 5, 6, 7, 8, 10, 12, 16, 20, 24, 28 }
Maximum number of transmissions for one HARQ process in DL when this QCI has the highest HARQ priority. Values higher than 7 will be treated as 7.

Specification: 3GPP 36.321

Takes effect: New connection
long dlMaxWaitingTime = 0 { 0..500 }
The scheduler attempts to achieve dlMaxWaitingTime for DL bearers before giving any DL bearer a higher priority. Value 0 means that the higher
priority is never applied. Must be set to a similar or slightly shorter value than the PDB. Setting too low a value can affect other services with higher
priority. For more information about PDB refer to TS 23.203.

Unit: 1 ms
Dependencies: Only used for Resource Fair Scheduling algorithm. Only relevant if the license for Advanced Differentiation for Resource Fair Scheduler
is present and the feature is active.
Disturbances: Changing this attribute can affect performance of all data bearers. A value that is set too low can affect other services with higher
priority. A value that is set too high can cause Dynamic UE Admission Control to fail in keeping the cell stable at overload.
Takes effect: New connection
long dlMinBitRate = 0 { 0..150000 }
The scheduler will attempt to achieve minbitrate for all bearers before giving any user a higher rate. Value 0 means that the minRate scheduler is not
used.

Unit: 1 kbps
Dependencies: This parameter will only be used if one of the following Proportional Fair scheduling algorithms, "maximum_C_over_I",
"proportional_fair_low", "proportional_fair_medium", "proportional_fair_high" or "equal_rate", has been selected.

Only relevant if the license for QoS Aware Scheduler is present and the feature is active.
Disturbances: Changing this attribute can cause loss of traffic.
Takes effect: New connection
ResourceAllocationStrategy dlResourceAllocationStrategy = RESOURCE_FAIR
Defines the downlink resource allocation strategy of the QoS Class Identifier (QCI).

Dependencies: Changes to this parameter take effect only if the licenses for Downlink Frequency Selective Scheduling and QoS Aware Scheduler are
present and the features are active.
Takes effect: New connection
about:blank 2/10
28/03/2025 19:33 class QciProfileOperatorDefined
long drxPriority = 0 { 0..100 }
The relative priority among the DRX profiles, i.e. if the bearer that is setup with this QCI has a higher DRX priority than any of the existing bearers, the
DRX configuration will be set to those selected by the drxProfileId for this QCI. The drxPriority has to be unique across all the configured
QciProfilePredefined and QciProfileOperatorDefined MOC instances except for instances where the drxProfileId is the same. That is, instances that
share the same drxProfileId may have the same drxPriority value. Also note that larger drxPriority values indicate higher relative priority.

Disturbances: Changing this attribute can cause loss of traffic. Possible mismatch between DRX setting used by network and UE for ongoing
connections.
Takes effect: Object unlocked
DrxProfile drxProfileRef
Points out the DRX profile associated with this QCI. If not set the default reference will be to the DrxProfile instance corresponding to Local
Distinguished Name (LDN) = ManagementElement=1, ENodeBFunction=1, DRxProfile=0.

Dependencies: The DRX profile must exist, otherwise it will be interpreted as default DRX profile.
Disturbances: Changing this attribute can cause loss of traffic. Possible mismatch between DRX setting used by network and UE for ongoing
connections.
Takes effect: Object unlocked
long dscp { 0..63 }
mandatory
The Differentiated Services Code Point for a Quality of Service Class Indicator (QCI). This corresponds to mappings from RAN QoS to Transport
Network QoS.

Dependencies: Applied if bearer has Allocation and Retention Priority (ARP) value for which DSCP value is not configured in dscpArpMap attribute.
Otherwise, value configured in dscpArpMap attribute is used.
Takes effect: New connection
DscpArpMap dscpArpMap
Defines DSCP to be used for each Allocation and Retention Priority (ARP).

Dependencies: Only relevant if license for DSCP Mapping Based on ARP and QCI is present and feature is active.
Takes effect: New connection
DualConnInitUlConf dualConnInitUlConf = MCG
noNotification
Indicates if MCG or SCG leg should be used for UL at initial state. It is set when dual connectivity is configured.

User category: Ericsson personnel

Takes effect: New connection
ManagedObject endcProfileRef
noNotification
Reference to an instance of EndcProfile or EndcProfilePredefined.
EN-DC profile associated with this QCI.

If not set, defaults to EndcProfilePredefined with LDN = ManagementElement=1, ENodeBFunction=1, EndcProfilePredefined=1.

User category: Ericsson personnel

Dependencies: Only applicable in Baseband Radio Node.

about:blank 3/10
28/03/2025 19:33 class QciProfileOperatorDefined
Disturbances: Changing this attribute can cause loss of traffic.
Takes effect: New connection
long harqPriority = 0 { 0..99 }
Relative HARQ priority of this QCI. If a bearer that is setup with this QCI has highest HARQ priority, HARQ transmission number is set to
ulMaxHARQTxQci and dlMaxHARQTxQci. HARQ priority must be unique for all configured MOC instances for QciProfilePredefined and
QciProfileOperatorDefined. Does not apply when ulMaxHARQTxQci and dlMaxHARQTxQci are same. Note that larger harqPriority values indicate
higher relative priority.

Takes effect: New connection

long inactivityTimerOffset = 0 { 0..65535 }
The offset time value that can be used to prolong the default inactivity timer.

Unit: 1 s
Takes effect: New connection
long lessMaxDelayThreshold = 0 { 0..20 }
Time delay that scheduling stays on-hold for Low Energy Scheduler Solution.
If 0, Low Energy Scheduler Solution is disabled.

Unit: 1 ms
Takes effect: New connection
LogicalChannelGroup logicalChannelGroupRef
mandatory
Refers to an instance of LogicalChannelGroup. Assigns a Logical Channel Group to a Quality of Service Class Indicator (QCI).

Takes effect: New connection

MeasReportConfigParams measReportConfigParams
Parameters for service-specific load management for a certain QCI profile.

Takes effect: New connection

boolean paPartitionOverride = false
Whether Priority Access (PA) bearers are included in partitioning.

Dependencies: Only relevant if the license for Radio Resource Partitioning is present and the feature is active.
Takes effect: New connection
long pdb = 80 { 0..500 }
The contribution from eNodeB to the Packet Delay Budget (PDB) for a QCI. Packet delays outside eNodeB e.g. in the transport network are excluded.
For more information about PDB refer to TS 23.203

Unit: 1 ms
Dependencies: Only relevant if the license for QoS Aware Scheduler is present and active.
Takes effect: Cell lock/unlock
long pdbOffset = 0 { -500..1000 }

about:blank 4/10
28/03/2025 19:33 class QciProfileOperatorDefined
An offset to the PDB used by Active Queue Management (AQM).

Unit: 1 ms
Dependencies: pdb + pdbOffset >= 0
Takes effect: Cell lock/unlock
long pdcpSNLength = 12 { 7, 12, 15 }
Indicates the Packet Data Convergence Protocol (PDCP) Sequence Number length in bits as specified in TS 36.323.

Dependencies: RLC UM must be configured (rlcMode = UM) to set this attribute to 7. RLC AM must be configured (rlcMode = AM) to set this attribute to
15. 15-bits PDCP SN is only applied if:
- pdcp-SN-Extension capability is indicated by UE; And
- UE is of category 11 or above; And
- UE is capable of at least 3C Carrier Aggregation.
Otherwise, default value of 12-bits PDCP SN is applied for RLC AM bearers.
Takes effect: Cell lock/unlock
long pdcpSNLengthNr = 18 { 12, 18 }
noNotification
Indicates the Packet Data Convergence Protocol (PDCP) Sequence Number length in bits as specified in TS 38.323.

User category: Ericsson personnel

Specification: 3GPP-TS-38.323
Takes effect: New connection
long priority { 0..14 }
mandatory
Decimal part of QCI-related priority.
Fractional part of priority is defined by priorityFraction attribute.

Dependencies: (priority + priorityFraction) > 0 AND (priority * 10 + priorityFraction) <= 140

Specification: 3GPP TS 23.203 (Release 12)
Disturbances: Changing this attribute can cause loss of traffic.
Takes effect: New connection
long priorityFraction = 0 { 0..9 }
Fractional part of QCI-related priority.
Decimal part of priority is defined by priority attribute.

Dependencies: (priority + priorityFraction) > 0 AND (priority * 10 + priorityFraction) <= 140

Specification: 3GPP TS 23.203 (Release 12)
Disturbances: Changing this attribute can cause loss of traffic.
Takes effect: New connection
long qci { 10..255 }
mandatory
Quality of Service Class Indicator (QCI) as defined in 3GPP TS 23.203 (Release 8). Each instance of this MO has a unique value for the QCI.
restricted

Dependencies: Each qci must be set to a unique value.

Takes effect: Object unlocked
long qciACTuning = 1000 { 1..1999 }
about:blank 5/10
28/03/2025 19:33 class QciProfileOperatorDefined
Tuning factor per QCI for admission control. Only valid for QCIs with resource type GBR.

Unit: 0.001 .
Dependencies: Only relevant if the license for Dynamic GBR admission control is present and the feature is active.
Takes effect: New connection
string QciProfileOperatorDefinedId
mandatory
The value component of the RDN.
noNotification
restricted
long qciSubscriptionQuanta = 1 { 0..50000 }
Normalized subscription quantity associated with the specific the QCI. Specifies the subscription cost of a bearer with this predefined profile. The
subscription cost is used for traffic load balancing purposes.

Disturbances: Changing this attribute can cause loss of traffic.

long relativePriority = 1 { 1..65535 }
The relative priority associated with a QCI.

Dependencies: Changes to this parameter take effect only if the feature states of the QoS Aware Scheduler , Proportional Fair Scheduler, and the Rps
are enabled.
Takes effect: New connection
ManagedObject[0..] reservedBy
noNotification
Contains a list of MO instances that reserve this MO instance.
readOnly
ResourceAllocationStrategy resourceAllocationStrategy = RESOURCE_FAIR
Defines the resource allocation strategy of the QoS Class Identifier (QCI).

Dependencies: Only relevant if the license for QoS Aware Scheduler is present and the feature is active
Takes effect: New connection
ResourceType resourceType
mandatory
Indicates if the resource type of the Quality of Service Class Indicator (QCI) is Guaranteed Bit Rate (GBR) or non-GBR as defined in 3GPP TS 23.203.
noNotification
restricted
Takes effect: Object unlocked
RlcMode rlcMode = AM
RLC Mode

Dependencies: Can only be set to AM if rlcSNLength is set to 10 or 16 and pdcpSNLength is set to 12 or 15. Must be set to UM if rlcSNLength is set to 5
or pdcpSNLength is set to 7.
Takes effect: Cell lock/unlock
long rlcSNLength = 10 { 5, 10, 16 }
Radio Link Control (RLC) Sequence Number length in bits as specified in TS 36.322.

Dependencies: RLC UM must be configured (rlcMode = UM) to set this attribute to 5. RLC AM must be configured (rlcMode = AM) to set this attribute to
16. 16-bit RLC SN is only applied if:

about:blank 6/10
28/03/2025 19:33 class QciProfileOperatorDefined
- extendedRLC-SN-SO-Field-r13 is indicated by UE; and
- 5CC DL Carrier Aggregation Extension license is enabled; and
- UE is capable of at least 5CC DL Carrier Aggregation.
Otherwise, default value of 10-bit RLC SN is applied for RLC AM bearers.
Takes effect: Cell lock/unlock
long rlfPriority = 0 { 0..100 }
The relative priority among the RLF (Radio Link Failure) profiles, i.e. if the bearer that is setup with this QCI has a higher RLF priority than any of the
existing bearers, the RLF configuration will be set to those selected by the rlfProfileId for this QCI. If more than one QCI has been configured with the
same and highest value of rlfPriority the RLF configuration will be set by the lowest QCI. The instances that share the same rlfProfileId may have the
same rlfPriority value. Also note that larger rlfPriority values indicate higher relative priority.

Takes effect: Object unlocked

RlfProfile rlfProfileRef
Points out the RLF profile associated with this QCI. If not set the default reference will be to the RlfProfile instance corresponding to Local
Distinguished Name (LDN) = ManagementElement=1, ENodeBFunction=1, RlfProfile=0.

Dependencies: The RLF profile must exist, otherwise it will be interpreted as default RLF profile.
Takes effect: Object unlocked
boolean rohcEnabled = false
Indicates if Robust Header Compression (ROHC) is enabled.
Note: Enabling ROHC is only supported for a QCI that is intended to carry RTP/RTCP/UDP based VoIP traffic as for example the standardized QCI1
(3GPP TS 23.203) and not for any other type of traffic.

Takes effect: New connection

boolean rohcForUlDataEnabled = false
Enables Robust Header Compression (ROHC) for data. Focus is on UL data, TCP/IP traffic, and related QCIs.

Dependencies: Must be false if rohcEnabled is true.

Takes effect: New connection
SchedulingAlgorithm schedulingAlgorithm = RESOURCE_FAIR
Specifies which scheduling algorithm is to be used for a certain QCI.

Dependencies: Only relevant if the license for QoS Aware Scheduler is present and the feature is active. The value DELAY_BASED can only be used if
the attribute serviceType has value VOIP.
Disturbances: Changing this attribute can cause loss of traffic.
Takes effect: New connection
ServiceType serviceType = UNDEFINED
Indicates the service that the bearer is used for.
ServiceType PTT and MC_SIGNALING cannot be set on QciProfileOperatorDefined MO.

Dependencies: Changes to this parameter take effect only if the license for QoS Aware Scheduler is present and the feature is active.
Takes effect: Cell lock/unlock

about:blank 7/10
28/03/2025 19:33 class QciProfileOperatorDefined
SrsAllocationStrategy srsAllocationStrategy = DEACTIVATED
If the parameter srsAllocationStrategy in the QoS configuration for a Data radio Bearer assigned to a UE is set to ACTIVATED, then an attempt is made
to allocate sounding for a UE. If several Data Radio Bearers are setup towards the UE with different QoS configurations, and the QoS configurations
has different QCI parameter, an algorithm using the priority parameter in the QoS configuration, will resolve which QoS configuration that will define
sounding

Takes effect: New connection

long timerPriority = 0 { 0..100 }
Relative priority among the timer profiles. TimerProfile with highest priority can be applied for a new connection in case the bearer QCI has an
associated TimerProfile.
In case several bearers with different QCIs are established, the TimerProfile with highest relative priority is applied.
The TimerProfile with lowest QCI number is applied, if TimerProfiles have the same priority,
Larger timerPriority value indicates higher relative priority.

Takes effect: Object unlocked

TimerProfile timerProfileRef
Refers to the timer profile associated with this QCI.

Takes effect: Object unlocked

long tReorderingDl = 35 { 0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 85, 100, 110,
120, 130, 140, 150, 160, 170, 180, 190, 200 }
This timer is used by the receiving end of Acknowledged Mode (AM) or Unacknowledged Mode (UM) Radio Link Control (RLC) entity in UE, to detect
loss of downlink RLC protocol data units at lower layers.

Dependencies: Not applicable for RLC TM. Only relevant when rlcMode is UM or AM
Takes effect: New connection
long tReorderingDlPdcp = 200 { 0, 20, 40, 60, 80, 100, 120, 140, 160, 180, 200, 220, 240, 260, 280, 300, 500, 750 }
noNotification
This timer is used by the receiving end of the Acknowledged Mode (AM) or Unacknowledged Mode (UM) Packet Data Convergence Protocol (PDCP)
entity in UE. When timer expires, missing packet are considered lost but packets received with earlier sequence number are sent upwards.

Unit: 1 ms
User category: Ericsson personnel
Specification: 3GPP-TS-38.331
Takes effect: New connection
long tReorderingUl = 35 { 0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 85, 100, 110,
120, 130, 140, 150, 160, 170, 180, 190, 200 }
This timer is used by the receiving end of the Acknowledged Mode (AM) or Unacknowledged Mode (UM) Radio Link Control (RLC) entity in eNB, to
detect loss of uplink RLC protocol data units at lower layers.

Unit: 1 ms
Dependencies: Not applicable for RLC TM. Only relevant when rlcMode is UM or AM
Takes effect: Cell lock/unlock

about:blank 8/10
28/03/2025 19:33 class QciProfileOperatorDefined
long tReorderingUlDiscardPdcp = 200 { 0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95,
noNotification
100, 110, 120, 130, 140, 150, 160, 170, 180, 190, 200, 220, 240, 260, 280, 300, 500, 750, 1000, 1500, 3000 }
This timer is a long timer and still receives missing packets when the tReorderingUlPdcp timer has been expired. When this timer expires, the PDCP
reception window is moved forward and any remaining very late arriving packets are discarded. Hence, any packets arriving after tReorderingUlPdcp
has expired but before tReorderingUlDiscardPdcp has expired can also be delivered to the network.

Unit: 1 ms
User category: Ericsson personnel
Dependencies: The parameter tReorderingUlDiscardPdcp must be equal or larger than tReorderingUlPdcp.
Takes effect: New connection
long tReorderingUlPdcp = 10 { 0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100,
noNotification
110, 120, 130, 140, 150, 160, 170, 180, 190, 200, 220, 240, 260, 280, 300, 500, 750, 1000, 1500, 3000 }
This timer is a short timer and used by the receiving end of the Acknowledged Mode (AM) or Unacknowledged Mode (UM) Packet Data Convergence
Protocol (PDCP) entity. Detects loss of PDCP uplink data units. When timer expires, received packets are delivered to higher layers.

Unit: 1 ms
User category: Ericsson personnel
Dependencies: The parameter tReorderingUlPdcp must be equal or less than tReorderingUlDiscardPdcp.
Takes effect: New connection
long ulMaxHARQTxQci = 5 { 1, 2, 3, 4, 5, 6, 7 }
Maximum number of transmissions for one HARQ process in UL when this QCI has the highest HARQ priority.

Specification: 3GPP 36.321

Takes effect: New connection
long ulMaxWaitingTime = 0 { 0..500 }
The scheduler attempts to achieve ulMaxWaitingTime for UL bearers before giving any UL bearer a higher priority. Value 0 means that the higher
priority is never applied. Must be set to a similar or slightly shorter value than the PDB. Setting too low a value can affect other services with higher
priority. For more information about PDB refer to TS 23.203.

Unit: 1 ms
Dependencies: Only used for Resource Fair Scheduling algorithm. Only relevant if the license for Advanced Differentiation for Resource Fair Scheduler
is present and the feature is active.
Disturbances: Changing this attribute can affect performance of all data bearers. A value that is set too low can affect other services with higher
priority. A value that is set too high can cause Dynamic UE Admission Control to fail in keeping the cell stable at overload.
Takes effect: New connection
long ulMinBitRate = 0 { 0..75000 }
The scheduler will attempt to achieve minbitrate for all bearers before giving any user a higher rate. Value 0 means that the minRate scheduler is not
used.

Unit: 1 kbps
Dependencies: This parameter will only be used if one of the following Proportional Fair scheduling algorithms, "maximum_C_over_I",
"proportional_fair_low", "proportional_fair_medium", "proportional_fair_high" or "equal_rate", has been selected.

about:blank 9/10
28/03/2025 19:33 class QciProfileOperatorDefined
Only relevant if the license for QoS Aware Scheduler is present and the feature is active.
Disturbances: Changing this attribute can cause loss of traffic.
Takes effect: New connection
string userLabel = "" [ 0..128 ]
Label for free use.
string zzzTemporary1 = ""
Temporary attributes are intended as temporary solutions. Their usage can vary depending on the installed software. It is strongly recommended to
only set the attributes that correspond to a desired functionality and leave all other temporary attributes set to default value. Information in the
descriptions about what attributes are in use can be overridden by the information in CPI documents. Note that a later release can use another
attribute to control functionality previously provided by a temporary attribute, or can remove functionality altogether. In these cases, the change is
documented in the NIR.
string zzzTemporary2 = ""
Temporary attributes are intended as temporary solutions. Their usage can vary depending on the installed software. It is strongly recommended to
only set the attributes that correspond to a desired functionality and leave all other temporary attributes set to default value. Information in the
descriptions about what attributes are in use can be overridden by the information in CPI documents. Note that a later release can use another
attribute to control functionality previously provided by a temporary attribute, or can remove functionality altogether. In these cases, the change is
documented in the NIR.
long zzzTemporary3 = -2000000000
Temporary attributes are intended as temporary solutions. Their usage can vary depending on the installed software. It is strongly recommended to
only set the attributes that correspond to a desired functionality and leave all other temporary attributes set to default value. Information in the
descriptions about what attributes are in use can be overridden by the information in CPI documents. Note that a later release can use another
attribute to control functionality previously provided by a temporary attribute, or can remove functionality altogether. In these cases, the change is
documented in the NIR.
long zzzTemporary4 = -2000000000
Temporary attributes are intended as temporary solutions. Their usage can vary depending on the installed software. It is strongly recommended to
only set the attributes that correspond to a desired functionality and leave all other temporary attributes set to default value. Information in the
descriptions about what attributes are in use can be overridden by the information in CPI documents. Note that a later release can use another
attribute to control functionality previously provided by a temporary attribute, or can remove functionality altogether. In these cases, the change is
documented in the NIR.
long zzzTemporary5 = -2000000000
Temporary attributes are intended as temporary solutions. Their usage can vary depending on the installed software. It is strongly recommended to
only set the attributes that correspond to a desired functionality and leave all other temporary attributes set to default value. Information in the
descriptions about what attributes are in use can be overridden by the information in CPI documents. Note that a later release can use another
attribute to control functionality previously provided by a temporary attribute, or can remove functionality altogether. In these cases, the change is
documented in the NIR.

class QciProfileOperatorDefined

about:blank 10/10