Applications:

Application 1: Lithium Battery Power Application 2: Lithium Battery Power

Charger Solar Panel

8.4DC 1.0A Built in lithium battery Built in lithium battery

Fully charged within 4 hours. Please In direct sunlight battery is fully

remove battery charger after full charge. charged within 2 days.

Programming:

Press PROG. Press PROG for Motor will shunt once. Press UP. Motor shunts once again.
Motor will beep 1 second. Programming is complete.

Change direction: (of travel if required)

Press STOP on the transmitter Motor will shunt once. Press DOWN. Motor shunts once again.
for 5 seconds. Programming is complete.

2
First limit position setting:
(If there’s no other action within 30 seconds. the motor will exit from the limit position preparation automatically)

Press PROG on the Motor will shunt once Press UP adjusting the Press PROG on the Motor shunts once
transmitter for 1 to indicate limit stop motor to the required transmitter for 1 again. The limit setting
second. setting mode. position to set the UP second. has been saved.
limit positionas first
limit. Or press DOWN to
set the DOWN limit stop
as the first position.

Other limit position settings:

(If there’s no other action within 30 seconds. the motor will exit from the limit position preparation automatically)

Move the motor to the Press PROG on the Motor will shunt Press PROG for 1 second Motor shunts once
desired position. transmitter for 1 second. once to indicate limit to save the limit position. again. The limit setting
setting mode. has been saved.

3
 Limit position fine tuning:
(If there’s no other action within 30 seconds. the motor will exit from the limit position preparation automatically)

Let the motor run into the Press PROG for 1 Motor will shunt once to
limit stop position that needs second. indicate limit setting mode.
fine tuning.

Adjust to the Press PROG for 1 second to save Motor shunts once again. The
required position. the limit position. fine tune setting has been
saved.

Delete the limit stop position (please note: the first limit position can’t be deleted)

Let the motor run to the Press PROG for Motor will shunt Within 7 seconds the motor will
limit stop position that is to 7 seconds. once to indicate limit shunt once again. The preset
be deleted. setting mode. limt position is now cleared.

4
Limit position setting:
1. A maximum of six different limit stop positions can be set. The furthest two
positions are called the UP and DOWN limit stop positions. The others are
called the middle limit stop positions;
2. When the first limit position is in the UP limit stop position (as below
illustration), all other limit positions can only be set below this position; the
same applies when setting the first DOWN limit stop position, all other limit
stop positions can only be set above this position;
3. Every limit stop position can be fine-tuned or deleted separately (The first
limit stop position can only be fine-tuned but can’t be deleted separately. It
can only be deleted by resetting the memory);
4. The motor will stop at the next limit stop position after accepting an UP/
DOWN instruction. When it reaches the UP limit stop position, any additional
UP instruction is cancelled out; when it reaches the DOWN limit stop
position, the DOWN instruction is also cancelled;
5. Pressing either the UP/DOWN button twice on the transmitter within 1
second will instruct the motor to go directly to the UP/DOWN limit stop
position without stopping at any middle limit stop.

The third limit stop position

The first limit stop position (Up limit position)

The third limit stop position

All the other

The second limit stop position limit positions
can be set below
the first limit
position
The third limit stop position

5
 Add the new transmitter:

Press STOP on the transmitter Motor will shunt once. Press UP on the new Motor shunts once again.
for 5 seconds. transmitter. The transmitter is stored.

Delete single channel memory:

Press STOP on the transmitter Motor will shunt once. Press PROG for 1 second. Motor shunts once again. Single
for 5 seconds. channel has been deleted.

Delete all the memories:

(After deleting all codes, the motor will be restored to factory setting)

Press STOP for 5 seconds. Motor will shunt once. Press PROG for 7 seconds Motor will shunt once. Motor will shunt twice
within 10 seconds of within 7 seconds. The
pressing STOP. memory has been deleted.

Turn the motor off:

Pres PROG on the Motor will beep and Motor will beep again after
motor for 7 seconds. shunt once. 7 seconds. The motor has
been turned off.

6
Trouble Shooting:
Items Problems Cause Solution

1. Connected with the wrong voltage

1. Change to the correct voltage
After connecting power,
2. Overloading
1 the motor doesn’t work 2. Choose suitable motor torque
or works slowly 3. Incorrect installation leading to
3. Check the components
motor jamming

The motor stops 1. Motor has exceeded overheating 1. After the motor has cooled sufficiently, motor
2 suddenly whilst protection +130oC will perform as required
running 2. Power was cut off 2. The motor will resume once power is back on