0 ECU is properly working

1 brSP NOT USED This code should not appear

2 brS1 NOT USED This code should not appear
3 brS0 NOT USED This code should not appear
4 sPdP NOT USED This code should not appear
5 PEd Select clutch pedal calibration procedure Press clutch pedal to confirm
this selection or move FNR lever to change
6 PCAL Perform clutch pedal calibration Press and release completely and
slowly the clutch pedal 3 times
7 CLU Select clutches calibration procedures Press clutch pedal to confirm
this selection or move FNR lever to change
8 CLUS Select clutches manual setting procedures Press clutch pedal to confirm
this selection or move FNR lever to change
9 CLUF Select clutches fill time manual setting Press clutch pedal to confirm
this selection or move FNR lever to change
10 CLUP Select clutches pressure threshold manual setting Press clutch pedal
to confirm this selection or move FNR lever to change
11 CLUA Select clutches automatic calibration procedure Press clutch pedal to
confirm this selection or move FNR lever to change
12 LOIL Transmission oil is too cold to start the procedure Heat oil between
60�C and 65�C and the procedure will automatically continue
13 HOIL Transmission oil is too hot to start the procedure Cool oil between
60�C and 65�C and the procedure will automatically continue
14 CCAL Clutches automatic calibration procedure is running Wait until
procedure has come to end avoiding riding clutch pedal or moving FNR lever
15 End Selected procedure successfully completed Switch off the engine to exit
16 FAIL ERROR: selected procedure completed but one or more failures occurred
Switch off the engine to exit
17 SCEr ERROR: clutch pedal angular sensor and end stroke switch signals not
congruent Press clutch pedal to continue
18 SIEr ERROR: clutch pedal end stroke switch not correctly installed Press
clutch pedal to continue
19 AIEr ERROR: clutch pedal angular sensor not correctly installed Press clutch
pedal to continue
20 SErr ERROR: reverse clutch fill time is too high Press clutch pedal to
continue
21 FErr ERROR: reverse clutch fill time is too low Press clutch pedal to
continue
22 HErr ERROR: reverse clutch does not engage with maximum pressurePress clutch
pedal to continue
23 LErr ERROR: reverse clutch engages with too low pressure Press clutch pedal
to continue
24 SErF ERROR: forward clutch fill time is too high Press clutch pedal to
continue
25 FErF ERROR: forward clutch fill time is too low Press clutch pedal to
continue
26 HErF ERROR: forward clutch does not engage with maximum pressurePress clutch
pedal to continue
27 LErF ERROR: forward clutch engages with too low pressure Press clutch pedal
to continue
28 SErH NOT USED This code should not appear
29 FErH NOT USED This code should not appear
30 HErH NOT USED This code should not appear
31 LErH NOT USED This code should not appear
32 SLEr WARNING: clutch slipping for excessive time Avoid riding clutch
pedal: risk of clutch burning
33 PSEr FAILURE: clutch pedal sensor and switch not congruent Avoid riding
clutch pedal and use only FNR lever: check angular sensor and switch signals and in
case perform clutch pedal calibration
34 PdHI FAILURE: clutch pedal sensor signal too high Avoid riding clutch
pedal and use only FNR lever: check angular sensor signal and in case perform
clutch pedal calibration
35 PdLO FAILURE: clutch pedal sensor signal too low Avoid riding clutch
pedal and use only FNR lever: check angular sensor signal and in case perform
clutch pedal calibration
36 EErr ERROR: flash memory not correctly rewrited Press clutch pedal to
continue
37 WARNING: transmission oil temperature too high Avoid using tractor
until temperature goes back in the proper range
38 PArb NOT USED This code should not appear
39 SGr1 NOT USED This code should not appear
40 SGr4 NOT USED This code should not appear
41 EnHI NOT USED This code should not appear
42 EnLo NOT USED This code should not appear
43 Err 13 NOT USED This code should not appear
44 Err 14 NOT USED This code should not appear
45 Err 15 NOT USED This code should not appear
46 Err 16 NOT USED This code should not appear
47 Err 17 NOT USED This code should not appear
48 Err 18 NOT USED This code should not appear
49 Err 19 NOT USED This code should not appear
50 Err 20 NOT USED This code should not appear
51 Err 21 NOT USED This code should not appear
52 Err 22 NOT USED This code should not appear
53 Err 23 NOT USED This code should not appear
54 Err 24 NOT USED This code should not appear
55 Err 25 NOT USED This code should not appear
56 Err 26 NOT USED This code should not appear
57 Err 27 FAILURE: temperature sensor signal too high Check temperature
sensor and harness
58 Err 28 NOT USED This code should not appear
59 Err 29 NOT USED This code should not appear
60 Err 30 NOT USED This code should not appear
61 Err 31 NOT USED This code should not appear
62 Err 32 NOT USED This code should not appear
63 Err 33 FAILURE: reverse clutch valve coil supply current request without
current feedback Check for feedback shorted to ground or open circuit
64 Err 34 FAILURE: reverse clutch valve coil supply current feedback
without current request Check for clutch supply pin shorted to 12V
65 Err 35 NOT USED This code should not appear
66 Err 36 NOT USED This code should not appear
67 Err 37 NOT USED This code should not appear
68 Err 38 NOT USED This code should not appear
69 Err 39 FAILURE: forward clutch valve coil supply current request without
current feedback Check for feedback shorted to ground or open circuit
70 Err 40 FAILURE: forward clutch valve coil supply current feedback
without current request Check for clutch supply pin shorted to 12V
71 Err 41 FAILURE: one or more clutch valve coil supply pin shorted to GND
Check for clutches supply pins shorted to GND or damaged coils
72 Err 42 NOT USED This code should not appear
73 Err 43 NOT USED This code should not appear
74 Err 44 NOT USED This code should not appear
75 Err 45 NOT USED This code should not appear
76 Err 46 NOT USED This code should not appear
77 Err 47 NOT USED This code should not appear
78 Err 48 NOT USED This code should not appear
79 Err 49 NOT USED This code should not appear
80 Err 50 NOT USED This code should not appear
81 dAtA NOT USED This code should not appear
82 Err 52 NOT USED This code should not appear
83 Err 53 FAILURE: ECU critical supply low voltage System will be stopped:
check for failure reason before restarting the system
84 Err 54 NOT USED This code should not appear
85 Err 55 NOT USED This code should not appear
86 Err 56 NOT USED This code should not appear
87 Err 57 NOT USED This code should not appear
88 Err 58 FAILURE: Reverse and Neutral signals simultaneously on FNR lever
System will be stopped: check for failure reason before restarting the system
89 Err 59 FAILURE: Forward and Neutral signals simultaneously on FNR lever
System will be stopped: check for failure reason before restarting the system
90 Err 60 FAILURE: Forward and Reverse signals simultaneously on FNR lever
System will be stopped: check for failure reason before restarting the system
91 Err 61 FAILURE: no signals on FNR lever System will be stopped: check
for failure reason before restarting the system
92 Err 62 NOT USED This code should not appear
93 Err 63 NOT USED This code should not appear
94 Err 64 NOT USED This code should not appear
95 Err 65 NOT USED This code should not appear
96 Err 66 NOT USED This code should not appear
97 Err 67 NOT USED This code should not appear
98 Err 68 NOT USED This code should not appear
99 Err 69 NOT USED This code should not appear
100 H 0 NOT USED This code should not appear
101 H 1 NOT USED This code should not appear
102 H 2 NOT USED This code should not appear
103 H 3 NOT USED This code should not appear
104 H 4 NOT USED This code should not appear
105 H 5 NOT USED This code should not appear
106 H 6 NOT USED This code should not appear
107 H 7 NOT USED This code should not appear
108 H 8 NOT USED This code should not appear
109 H 9 NOT USED This code should not appear
110 H 10 NOT USED This code should not appear
111 H 11 NOT USED This code should not appear
112 H 12 NOT USED This code should not appear
113 H 13 NOT USED This code should not appear
114 H 14 NOT USED This code should not appear
115 H 15 NOT USED This code should not appear
116 H 16 NOT USED This code should not appear
117 H 17 NOT USED This code should not appear
118 H 18 NOT USED This code should not appear
119 H 19 NOT USED This code should not appear
120 H 20 NOT USED This code should not appear
121 H 21 NOT USED This code should not appear
122 H 22 NOT USED This code should not appear
123 H 23 NOT USED This code should not appear
124 H 24 NOT USED This code should not appear
125 H 25 NOT USED This code should not appear
126 H 26 NOT USED This code should not appear
127 H 27 NOT USED This code should not appear
128 H 28 NOT USED This code should not appear
129 H 29 NOT USED This code should not appear
130 H 30 NOT USED This code should not appear
131 H 31 NOT USED This code should not appear
132 H 32 NOT USED This code should not appear
133 H 33 NOT USED This code should not appear
134 H 34 NOT USED This code should not appear
135 H 35 NOT USED This code should not appear
136 H 36 NOT USED This code should not appear
137 H 37 NOT USED This code should not appear
138 H 38 NOT USED This code should not appear
139 H 39 NOT USED This code should not appear
140 H 40 NOT USED This code should not appear
141 rAHI High Range is not engaged Engage High Range on Ranges Lever and the
procedure will automatically continue
142 rAME NOT USED This code should not appear
143 trPA NOT USED This code should not appear
144 trCA Select tractor calibration procedures Press clutch pedal to confirm
this selection
145 F 0 Forward: 0 Place FNR Lever in FWD to increase the value. Press clutch
pedal to select and continue.
146 F 1 Forward: 1 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
147 F 2 Forward: 2 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
148 F 3 Forward: 3 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
149 F 4 Forward: 4 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
150 F 5 Forward: 5 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
151 F 6 Forward: 6 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
152 F 7 Forward: 7 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
153 F 8 Forward: 8 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
154 F 9 Forward: 9 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
155 F 10 Forward: 10 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
156 F 11 Forward: 11 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
157 F 12 Forward: 12 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
158 F 13 Forward: 13 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
159 F 14 Forward: 14 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
160 F 15 Forward: 15 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
161 F 16 Forward: 16 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
162 F 17 Forward: 17 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
163 F 18 Forward: 18 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
164 F 19 Forward: 19 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
165 F 20 Forward: 20 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
166 F 21 Forward: 21 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
167 F 22 Forward: 22 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
168 F 23 Forward: 23 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
169 F 24 Forward: 24 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
170 F 25 Forward: 25 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
171 F 26 Forward: 26 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
172 F 27 Forward: 27 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
173 F 28 Forward: 28 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
174 F 29 Forward: 29 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
175 F 30 Forward: 30 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
176 F 31 Forward: 31 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
177 F 32 Forward: 32 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
178 F 33 Forward: 33 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
179 F 34 Forward: 34 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
180 F 35 Forward: 35 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
181 F 36 Forward: 36 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
182 F 37 Forward: 37 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
183 F 38 Forward: 38 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
184 F 39 Forward: 39 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
185 F 40 Forward: 40 Place FNR Lever in REV to decrease the value. Press clutch
pedal to select and continue.
186 StOP Press brake pedal until the tractor is stopped Perform requested action
187 FOr Place FNR lever in forward position Perform requested action
188 nEU Place FNR lever in neutral position Perform requested action
189 rEPE NOT USED This code should not appear
190 r 0 Reverse: 0 Place FNR Lever in FWD to increase the value. Press clutch
pedal to select and continue.
191 r 1 Reverse: 1 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
192 r 2 Reverse: 2 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
193 r 3 Reverse: 3 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
194 r 4 Reverse: 4 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
195 r 5 Reverse: 5 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
196 r 6 Reverse: 6 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
197 r 7 Reverse: 7 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
198 r 8 Reverse: 8 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
199 r 9 Reverse: 9 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
200 r 10 Reverse: 10 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
201 r 11 Reverse: 11 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
202 r 12 Reverse: 12 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
203 r 13 Reverse: 13 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
204 r 14 Reverse: 14 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
205 r 15 Reverse: 15 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
206 r 16 Reverse: 16 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
207 r 17 Reverse: 17 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
208 r 18 Reverse: 18 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
209 r 19 Reverse: 19 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
210 r 20 Reverse: 20 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
211 r 21 Reverse: 21 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
212 r 22 Reverse: 22 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
213 r 23 Reverse: 23 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
214 r 24 Reverse: 24 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
215 r 25 Reverse: 25 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
216 r 26 Reverse: 26 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
217 r 27 Reverse: 27 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
218 r 28 Reverse: 28 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
219 r 29 Reverse: 29 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
220 r 30 Reverse: 30 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
221 r 31 Reverse: 31 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
222 r 32 Reverse: 32 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
223 r 33 Reverse: 33 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
224 r 34 Reverse: 34 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
225 r 35 Reverse: 35 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
226 r 36 Reverse: 36 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
227 r 37 Reverse: 37 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
228 r 38 Reverse: 38 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
229 r 39 Reverse: 39 Place FNR Lever in FWD to increase, in REV to decrease the
value. Press clutch pedal to select and continue.
230 r 40 Reverse: 40 Place FNR Lever in REV to decrease the value. Press clutch
pedal to select and continue.
231 rEU MSG: Place FNR lever in reverse position Perform requested action
232 EntY NOT USED This code should not appear
233 HCAL NOT USED This code should not appear
234 FCAL NOT USED This code should not appear
235 rCAL NOT USED This code should not appear
236 ALCL NOT USED This code should not appear
237 F CL NOT USED This code should not appear
238 rECL NOT USED This code should not appear
239 FHCL NOT USED This code should not appear
240 trtY NOT USED This code should not appear
241 tr 1 NOT USED This code should not appear
242 tr 2 NOT USED This code should not appear
243 tr 3 NOT USED This code should not appear
244 tr 4 NOT USED This code should not appear
245 tr 5 NOT USED This code should not appear
246 tr 6 NOT USED This code should not appear
247 tr 7 NOT USED This code should not appear
248 tr 8 NOT USED This code should not appear
249 tr 9 NOT USED This code should not appear
250 En 1 NOT USED This code should not appear
251 En 2 NOT USED This code should not appear
252 En 3 NOT USED This code should not appear
253 En 4 NOT USED This code should not appear
254 En 5 NOT USED This code should not appear
255 En 6 NOT USED This code should not appear