VALVES

2.01
VALVES

Sureflow Gate Valves 2.03

(Resilient, Metal)
Check Valves 2.23
Butterfly Valves 2.33
Hydrant Valves 2.47
Knife Gate Valves 2.55
Air Valves 2.57
Valve Ancillary 2.63

2.02
VALVES

SUREFLOW
GATE VALVES
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW®

VALVES / SUREFLOW GATE VALVES

GATE VALVES OVERVIEW

ON-OFF GATE VALVES DESIGNED FOR THE PRIMARY FUNCTION OF FLOW ISOLATION

Gate valves feature a sliding partition that There is a growing industry trend to use
can be closed to block flow or opened fully gate valves in flow regulating and scour
for maximum flow. applications. When gate valves are used in
these applications it is essential that they FULLY
Gate valves are used to isolate sections of OPENED
are operated in the fully opened position ISOLATION
pipelines, branch off-takes and pieces of
and any regulation of flow controlled by ORIFICE PLATE VALVE
equipment. They are on-off valves designed
other means, such as orifice plates.
for the primary function of flow isolation
and should only be operated in the fully Orifice plates choke the flow and reduce
closed or fully open positions. The sliding head loss across the gate valve thus
motion of the gate is effected by a rotating preventing valve damage.
screw, known as a spindle or stem.
Gate valves should not be used for
Sluice valves are gate valves and prior to throttling or adjusting flow as associated
the introduction of fusion bonded coatings turbulence and high velocity can lead to FULLY SECONDARY
they were of a heavier construction to vibration, chattering and fretting wear, as OPENED ISOLATION
PRIMARY VALVE
endure buried service applications, well as cavitation damage of the valve and ISOLATION
whereas gate valves were associated downstream pipeline. VALVE

with above ground applications. Today’s

When used as a control or modulating
modern coating systems remove the need
valve this can also lead to these problems,
for distinction between buried and above
the installation of a secondary valve for
ground applications and therefore no need
isolation purposes is recommended.
for sluice valve and gate valve distinction.
Secondary isolation valve used for control
or modulating purposes. Primary isolation
valve used for isolation purposes only.
CERTIFICATIONS

When throttling is necessary, globe or

butterfly valves should be used. AS2638.1 - Metal Seated Gate Valves
AS2638.2 - Resilient Seated Gate Valves
Certified Product - AS2638.1/AS2638.2
THROTTLING
WaterMark Level 1 Certification

When gate valves are fully opened their

head loss coefficient KL is in order of 0.12.
Note. The flow through the valve is not
directly proportional to the number of turns
of the valve spindle.

CSA – Velocity VS Percentage Open

CSA
Velocity
5
10

15

20

25

30

35

40

45

50

55

60

65
70
75

80

85

90

95

100

PERCENTAGE OPEN

2.04
 VALVES / SUREFLOW GATE VALVES
VALVES

2.05
 VIADUX WATER NETWORK SOLUTIONS

GATE VALVES OVERVIEW

VALVES / SUREFLOW GATE VALVES

DESIGN OPTIONS – METAL SEATED OR RESILIENT SEATED

There are two design options for Gate

Valves, Metal Seated and Resilient Seated.
These two options can also be split into
two categories Non-Rising Spindle (Inside
Screw) and Rising Spindle (Outside Screw).
Non-Rising Spindle Gate valves are
suitable for above ground and
underground installations but are used
predominately in underground installations
because spindle movement is rotational
only and additional cover is not required to
accommodate the opened valve.
Rising Spindle Gate valves are
predominately used for above ground and
valve pit installations. They are commonly
used in fire service applications where a
positive indication of the open or closed
position is necessary.
The SUREFLOW® range of Gate Valves
employs an articulated gate design where
the wedge nut is located separately within
a housing in the gate. This articulated gate
design has key advantages over systems METAL SEATED GATE VALVES RESILIENT SEATED GATE VALVES
where the stem nut is integral with the
gate. It overcomes the risk of damage
through direct pressure on the stem, stem Metal seated gate valves comprise a metal Resilient seated gate valves contain an
nut or other components during operation gate, typically wedge shaped and made of EPDM rubber encapsulated ductile iron
or transitional throttling. gunmetal for valves up to and including gate. The valve is closed by appropriate
200mm and ductile iron with gunmetal rotation of the spindle which drives the
The use of gate valves for end of line sealing rings for larger sizes. gate against the cast internal sealing
isolation is not recommended. If the valves surfaces of the valve body. These surfaces
are to be fitted to the end of a line we The gate and body are fitted with metal
are normally coated with fusion bonded
recommend the use of a blank flange or sealing rings by threading or plastic
polymers such as epoxy or nylon.
plug to ensure isolation of the line. deformation to prevent loosening in
service. A continuous seal is provided Sealing is achieved by the compression
behind the rings to prevent corrosion. of the EPDM rubber coating on the gate
against the valve body. In resilient seated
The valve is closed by appropriate rotation
gate valves, maximum torque of the
of the spindle which drives the gate
spindle is associated with closing the valve
down between the sealing rings. Sealing
to overcome the effects of friction and
is effected by the mating of the sealing
compression of the EPDM rubber coating.
rings. Sometimes the sealing surfaces
Properly operated and closed, these valves
can become damaged from the impact of
can effect a drop tight seal.
foreign debris or from foreign debris being
lodged between the sealing faces. The gate is body guided throughout the
major portion of its closure and secondary
Throttling of a metal seated gate valve is
guides become effective near the end of its
the most common cause of damage to
travel to ensure correct seat alignment.
the sealing faces. Repair of the sealing
surfaces is not a simple operation and a
factory refit is normally necessary.
In metal seated gate valves, maximum
torque on the spindle is associated with
initial opening or ‘cracking’ of the valve.
Properly operated and closed, these valves
can effect a drop tight seal but leakage
rates of 2-10 ml/min are acceptable
under AS 2638.1.

2.06
 VALVES
VALVES / RESILIENT SEATED VALVES

SUREFLOW
RESILIENT
SEATED VALVES

2.07
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW®

VALVES / RESILIENT SEATED VALVES

RESILIENT SEATED VALVES

RESILIENT SEATED PN 16 – PN 25

FLANGED PN16 – DN80 - DN600

Code Size (MM) Description
VRACC08500AK 80 80 FL AUSLITE III VALVE B5 ACC
VRACC08500CK 80 80 FL AUSLITE III VALVE B5 CC
VRACC10500AK 100 100 FL AUSLITE III VALVE B5 ACC
VRACC10500CK 100 100 FL AUSLITE III VALVE B5 CC
VRACC15500AK 150 150 FL AUSLITE III VALVE B5 ACC
VRACC15500CK 150 150 FL AUSLITE III VALVE B5 CC
VRACC20500AK 200 200 FL AUSLITE III VALVE B5 ACC
VRACC20500CK 200 200 FL AUSLITE III VALVE B5 CC
VRACC22500AK 225 225 FL AUSLITE III VALVE B5 ACC
VRACC22500CK 225 225 FL AUSLITE III VALVE B5 CC
VRACC25500AK 250 250 FL AUSLITE III VALVE B5 ACC
VRACC25500CK 250 250 FL AUSLITE III VALVE B5 CC
VRACC30500AK 300 300 FL AUSLITE III VALVE B5 ACC
VRACC30500CK 300 300 FL AUSLITE III VALVE B5 CC
VRACC37500AK 375 375 FL AUSLITE III VALVE B5 ACC
VRACC37500CK 375 375 FL AUSLITE III VALVE B5 CC
VRACC40500AK 400 400 FL AUSLITE III VALVE B5 ACC
VRACC40500CK 400 400 FL AUSLITE III VALVE B5 CC
VRDCC45500A 450 450 FL RS VALVE B5 ACC FIG 500
VRDCC45500C 450 450 FL RS VALVE B5 CC FIG 500
VRDCC50500A 500 500 FL RS VALVE B5 ACC FIG 500
VRDCC50500C 500 500 FL RS VALVE B5 CC FIG500
VRDCC60500A 600 600 FL RS VALVE B5 ACC FIG 500
VRDCC60500C 600 600 FL RS VALVE B5 CC FIG 500

FLANGED PN25 – DN80 - DN150

Code Size (MM) Description
VRAFF08500A 80 80 FL AUSLITE VALVE PN25 ACC
VRAFF08500C 80 80 FL AUSLITE VALVE PN25 CC
VRAFF10500A 100 100 FL AUSLITE VALVE PN25 ACC
VRAFF10500C 100 100 FL AUSLITE VALVE PN25 CC
VRAFF15500A 150 150 FL AUSLITE VALVE PN25 ACC
VRAFF15500C 150 150 FL AUSLITE VALVE PN25 CC

2.08
 VALVES

SUREFLOW RESILIENT SEATED GATE VALVE

VALVES / RESILIENT SEATED VALVES

RESILIENT SEATED FLANGED PN 16 – PN 25

SOCKET – DN100 - DN375

Code Size (MM) Description
VRATT10500A 100 100 SC AUSLITE VALVE ACC PN16
VRATT10500C 100 100 SC AUSLITE VALVE CC PN16
VRATT15500A 150 150 SC AUSLITE VALVE ACC PN16
VRATT15500C 150 150 SC AUSLITE VALVE CC PN16
VRDTT20500A 200 200 SC RS VALVE ACC FIG 500
VRDTT20500C 200 200 SC RS VALVE CC FIG 500
VRDTT22500A 225 225 SC RS VALVE ACC FIG 500
VRDTT22500C 225 225 SC RS VALVE CC FIG 500
VRDTT25500A 250 250250 SC RS VALVE ACC FIG 500
VRDTT25500C 250 250 SC RS VALVE CC FIG 500
VRDTT30500A 300 300 SC RS VALVE ACC FIG 500
VRDTT30500C 300 300 SC RS VALVE CC FIG 500
VRDTT37500A 375 375 SC RS VALVE ACC FIG 500
VRDTT37500C 375 375 SC RS VALVE CC FIG 500

SPIGOT – DN80 - DN300

Code Size (MM) Description
VRASS08500A 80 80 SP AUSLITE VALVE ACC PN16
VRASS08500C 80 80 SP AUSLITE VALVE CC PN16
VRASS10500A 100 100 SP AUSLITE VALVE ACC PN16
VRASS10500C 100 100 SP AUSLITE VALVE CC PN16
VRASS15500A 150 150 SP AUSLITE VALVE ACC PN16
VRASS15500C 150 150 SP AUSLITE VALVE CC PN16
VRDSS20500A 200 200 SP RS VALVE ACC FIG 500
VRDSS20500C 200 200 SP RS VALVE CC FIG 500
VRDSS22500A 225 225 SP RS VALVE ACC FIG 500
VRDSS22500C 225 225 SP RS VALVE CC FIG 500
VRDSS25500A 250 250 SP RS VALVE ACC FIG 500
VRDSS25500C 250 250 SP RS VALVE CC FIG 500
VRDSS30500A 300 300 SP RS VALVE ACC FIG 500
VRDSS30500C 300 300 SP RS VALVE CC FIG 500

FLANGE-SOCKET – DN100 - DN150

Code Size (MM) Description
VRACT10500A 100 100 FL-SC AUSLITE VALVE B5 ACC
VRACT10500C 100 100 FL-SC AUSLITE VALVE B5 CC
VRACT15500A 150 150 FL-SC AUSLITE VALVE B5 ACC
VRACT15500C 150 150 FL-SC AUSLITE VALVE B5 CC

2.09
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW RESILIENT SEATED GATE VALVE

VALVES / RESILIENT SEATED VALVES

RESILIENT SEATED SOCKET, SPIGOT AND FLANGED-SOCKET

RESILIENT SEATED – PN 16
Nom. Dimensions
Size
DN bmax L1 L2 L3 L4

80 350 203 - 340 -

bmax
100 375 229 120 365 175
150 460 267 130 380 199
200 560 292 195 410 -
225 645 305 205 420 -
250 655 330 235 435 -
300 740 356 245 450 -

bmax
375 915 381 275 - -
bmax

400 930 406 - - -

450 1145 432 - - -
500 1280 457 - - -
600 1465 508 - - -
L1
bmax

RESILIENT SEATED – PN 25 FLANGED

Nom. Dimensions
Size
DN bmax L1

80 350 203
100 375 229
L1 L2
150 460 267
FLANGED
Larger sizes in development TYTON SOCKET
L1
Normal application: Isolation of sections and
FLANGED branches of a pipeline or provision of manual
control at discharge points

AUSLITE® valves are highlighted in salmon.

L1 L2 L3

FLANGED TYTON SOCKET SPIGOT

L2

TYTON SOCKET

L3
L2
L4
TYTON SOCKET SPIGOT
FLANGED - TYTON SOCKET
L3

SPIGOT

L3
L4
SPIGOT
FLANGED - TYTON SOCKET
2.10
L4
 PRODUCT RANGE GUIDE
VALVES

SUREFLOW RESILIENT SEATED GATE VALVE

VALVES / RESILIENT SEATED VALVES

RESILIENT SEATED SHOULDER END – DN 100 & DN 150 NON RISING SPINDLE

PN25 – DN100 & DN150

Code Size (MM) Description
VRAXX10500CH 100 100 SH END NRSP AUSLITE VLV CC
VRAXX15500CH 150 150 SH END NRSP AUSLITE VLV CC

DIMENSIONS
Mass Turns Torque
DN E G
KG to Seal to Seal

100 229 320 15 21 40

150 267 395 20 32 60
G – APPROX.
ØF – NOMINAL BORE
ØB
ØA

C
D
E±2

2.11
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW RESILIENT SEATED GATE VALVE

VALVES / RESILIENT SEATED VALVES

FIGURE 500 INTEGRAL BYPASS ARE DESIGNED AND MANUFACTURED TO AS 2638.2

INTERGAL BYPASS PN16 – DN375 - DN600

Code Size (MM) Description
VRDCC37500AB 375 375X100 FL RS BYP VLV B5 ACC
VRDCC37500CB 375 375X100 FL RS BYP VLV B5 CC
VRDCC45500AB 450 450X100 FL RS BYP VLV B5 ACC
VRDCC45500CB 450 450X100 FL RS BYP VLV B5 CC
VRDCC50500AB 500 500X150 FL RS BYP VLV B5 ACC
VRDCC50500CB 500 500X150 FL RS BYP VLV B5 CC
VRDCC60500AB 600 600X150 FL RS BYP VLV B5 ACC
VRDCC60500CB 600 600X150 FL RS BYP VLV B5 CC

DIMENSIONS
Valve DN 375 450 500 600
Size DN 100 100 150 150

A MM 960 1145 1280 1460

B MM 635 665 780 855
C MM 610 660 710 785

2.12
 VALVES

SUREFLOW RESILIENT SEATED GATE VALVE

VALVES / RESILIENT SEATED VALVES

FIGURE 500H & 500R RESILIENT SEATED GATE VALVES DESIGNED AND MANUFACTURED TO AS 2638.2 FOR ABOVE GROUND USE

HAND WHEEL-FLANGED PN16 – DN80 - DN600

Code Size (MM) Description
VRACC08500AH 80 80 FL NRSP A/LITE B5 ACC 500H
VRACC08500CH 80 80 FL NRSP A/LITE B5 CC 500H
VRACC10500AH 100 100 FL NRSP A/LITE B5 ACC 500H
VRACC10500CH 100 100 FL NRSP AUSLITE B5 CC 500H
VRACC15500AH 150 150 FL NRSP A/LITE B5 ACC 500H
VRACC15500CH 150 150 FL NRSP A/LITE B5 CC 500H
VRDCC20500AH 200 200 FL NRSP RSV B5 ACC FIG500H
VRDCC20500CH 200 200 FL NR/SP RSV B5 CC FIG500H
VRDCC25500AH 250 250 FL NRSP RSV B5 ACC FIG500H
VRDCC25500CH 250 250 FL NRSP RSV B5 CC FIG500H
VRDCC30500AH 300 300 FL NRSP RSV B5 ACC FIG500H
VRDCC30500CH 300 300 FL NRSP RSV B5 CC FIG500H

FIGURE 500H DIMENSIONS

Valve Size DN 80 100 150 200 250 300
Height - HH MM 367 402 502 610 723 810
Length - L MM 203 229 267 292 330 356

HH

2.13
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW® GATE VALVES

VALVES / RESILIENT SEATED VALVES

FIGURE 500H & 500R RESILIENT RISING SEATED GATE VALVES DESIGNED AND MANUFACTURED TO AS 2638.2 FOR ABOVE GROUND USE

RISING SPINDLE (OS&Y)-FLANGED PN16 – DN80 - DN600

Code Size (MM) Description
VRACC08500RC 80 80 FL AUSLITE R/SP RSV B5 CC
VRACC10500RC 100 100 FL AUSLITE R/SP RSV B5 CC
VRACC10500RC 150 150 FL AUSLITE R/SP RSV B5 CC
VRDCC20500RC 200 200 FL R/SP RSV B5 CC FIG500R
VRDCC25500RC 250 250 FL R/SP RSV B5 CC FIG500R
VRDCC30500RC 300 300 FL R/SP RSV B5 CC FIG500R

FIGURE 500R DIMENSIONS

Valve Size DN 80 100 150 200 250 300
Height – HR - Open MM 512 590 788 930 1200 1390
- Closed MM 425 483 630 722 940 1080
Length – L MM 203 229 267 292 330 356

HR

2.14
 VALVES
VALVES / M ETAL SEATED GATE VALVES

SUREFLOW
METAL SEATED
GATE VALVES

2.15
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW®

VALVES / METAL SEATED GATE VALVES

METAL SEATED GATE VALVES

METAL SEATED GATE VALVES ARE DESIGNED AND MANUFACTURED TO AS 2638.1

FLANGED - PN16 -DN80-900

Code Size (MM) Description
VSDCC08400A 80 80 FL MS VALVE B5 ACC FIG 400
VSDCC08400C 80 80 FL MS VALVE B5 CC FIG 400
VSDCC10400A 100 100 FL MS VALVE B5 ACC FIG 400
VSDCC10400C 100 100 FL MS VALVE B5 CC FIG 400
VSDCC15400A 150 150 FL MS VALVE B5 ACC FIG 400
VSDCC15400C 150 150 FL MS VALVE B5 CC FIG 400
VSDCC20400A 200 200 FL MS VALVE B5 ACC FIG 400
VSDCC20400C 200 200 FL MS VALVE B5 CC FIG 400
VSDCC22400A 225 225 FL MS VALVE B5 ACC FIG 400
VSDCC22400C 225 225 FL MS VALVE B5 CC FIG 400
VSDCC25400A 250 250 FL MS VALVE B5 ACC FIG 400
VSDCC25400C 250 250 FL MS VALVE B5 CC FIG 400
VSDCC30400A 300 300 FL MS VALVE B5 ACC FIG 400
VSDCC30400C 300 300 FL MS VALVE B5 CC FIG 400
VSDCC37400A 375 375 FL MS VALVE B5 ACC FIG 400
VSDCC37400C 375 375 FL MS VALVE B5 CC FIG 400
VSDCC45400A 450 450 FL MS VALVE B5 ACC FIG 400
VSDCC45400C 450 450 FL MS VALVE B5 CC FIG 400
VSDCC50400A 500 500 FL MS VALVE B5 ACC FIG 400
VSDCC50400C 500 500 FL MS VALVE B5 CC FIG 400
VSDCC60400A 600 600 FL MS VALVE B5 ACC FIG 400
VSDCC60400C 600 600 FL MS VALVE B5 CC FIG 400
VSDCC75400AG 750 750 FL MSV B5 ACC 12:1 G/BX
VSDCC75400CG 750 750 FL MSV B5 CC 12:1 G/BX
VSDCC90400AG 900 900 FL MSV B5 ACC 16:1 G/BX
VSDCC90400CG 900 900 FL MSV B5 CC 16:1 G/BX

Dn1000+ Valves – Price and availability upon request, subject to customer

requirements

2.16
 PRODUCT RANGE GUIDE
VALVES

SUREFLOW®
VALVES / M ETAL SEATED GATE VALVES

METAL SEATED GATE VALVES

METAL SEATED GATE VALVES ARE DESIGNED AND MANUFACTURED TO AS 2638.1

FLANGED - PN35 -DN80-900

Code Size (MM) Description
VSDFF08400A 80 80 FL MS VALVE B6 ACC FIG 400
VSDFF08400C 80 80 FL MS VALVE B6 CC FIG 400
VSDFF10400A 100 100 FL MS VALVE B6 ACC FIG 400
VSDFF10400C 100 100 FL MS VALVE B6 CC FIG 400
VSDFF15400A 150 150 FL MS VALVE B6 ACC FIG 400
VSDFF15400C 150 150 FL MS VALVE B6 CC FIG 400
VSDFF20400A 200 200 FL MS VALVE B6 ACC FIG 400
VSDFF20400C 200 200 FL MS VALVE B6 CC FIG 400
VSDFF22400A 225 225 FL MS VALVE B6 ACC FIG 400
VSDFF22400C 225 225 FL MS VALVE B6 CC FIG 400
VSDFF25400A 250 250 FL MS VALVE B6 ACC FIG 400
VSDFF25400C 250 250 FL MS VALVE B6 CC FIG 400
VSDFF30400A 300 300 FL MS VALVE B6 ACC FIG 400
VSDFF30400C 300 300 FL MS VALVE B6 CC FIG 400
VSDFF37400A 375 375 FL MS VALVE B6 ACC FIG 400
VSDFF37400C 375 375 FL MS VALVE B6 CC FIG 400
VSDFF45400A 450 450 FL MS VALVE B6 ACC FIG 400
VSDFF45400C 450 450 FL MS VALVE B6 CC FIG 400
VSDFF50400A 500 500 FL MS VALVE B6 ACC FIG 400
VSDFF50400C 500 500 FL MS VALVE B6 CC FIG 400
VSDFF60400AG 600 600 FL MSV B6 ACC 12:1 G/BX
VSDFF60400CG 600 600 FL MSV B6 CC 12:1 G/BX
VSDFF75400AG 750 750 FL MSV B6 ACC 24:1 G/BX
VSDFF75400CG 750 750 FL MSV B6 CC 24:1 G/BX
VSDFF90400AG 900 900 FL MSV PN35 ACC 32:1 G/BX
VSDFF90400CG 900 900 FL MSV PN35 CC 32:1 G/BX

Dn1000+ Valves – Price and availability upon request, subject to customer

requirements

PN 16 PN 35
Nom. Dimensions Nom. Dimensions
Size Size
DN bmax L1 DN bmax L1
80 367 203 80 367 280
100 402 229 100 402 305
150 502 267 150 502 330
200 610 292 200 610 380
bmax

225 649 305 225 649 405

250 723 330 250 723 420
300 810 356 300 810 430
375 960 381 375 960 610
450 1145 432 450 1145 660
500 1290 457 500 1290 710
600 1467 508 600 1467 785
750 2255* 610 750 2255* 950
900 2550* 711 900 2550* 1100

*Includes gearbox
L1
Normal application: Isolation of sections and branches of a pipeline
FLANGED
or provision of manual control at discharge points.

2.17
VIADUX WATER NETWORK SOLUTIONS

VALVES / METAL SEATED GATE VALVES

2.18
 PRODUCT RANGE GUIDE
VALVES

SUREFLOW® METAL SEATED GATE VALVE

VALVES / M ETAL SEATED GATE VALVES

FIGURE 600H METAL SEATED GATE VALVES ARE DESIGNED AND MANUFACTURED TO AS 2638.1 FOR ABOVE GROUND USE

FLANGED PN16 – FIG 600 TABLE E

Code Size (MM) Description
VGDEE08600C 80 80 FL NR/SP MSV TE CC FIG600
VGDEE10600C 100 100 FL NR/SP MSV TE CC FIG600
VGDEE15600C 150 150 FL NR/SP MSV TE CC FIG600
VGDEE20600C 200 200 FL NR/SP MSV TE CC FIG600
VGDEE25600C 250 250 FL NR/SP MSV TE CC FIG600
VGDEE30600C 300 300 FL NR/SP MSV TE CC FIG600

FIGURE 600H DIMENSIONS

Valve Size DN 80 100 150 200 250 300
Height – HH MM 367 402 502 610 723 810
Length – L MM 203 229 267 292 330 356

HH

2.19
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW® METAL SEATED GATE VALVE

VALVES / METAL SEATED GATE VALVES

FIGURE 601 METAL SEATED GATE VALVES ARE DESIGNED AND MANUFACTURED TO AS 2638.1 FOR ABOVE GROUND USE

FLANGED PN16 – FIG 601 TABLE E

Code Size (MM) Description
VGDEE08601C 80 80 FL R/SP MSV TE CC FIG601
VGDEE10601C 100 100 FL R/SP MSV TE CC FIG601
VGDEE15601C 150 150 FL R/SP MSV TE CC FIG601
VGDEE20601C 200 200 FL R/SP MSV TE CC FIG601
VGDEE25601C 250 250 FL R/SP MSV TE CC FIG601
VGDEE30601C 300 300 FL R/SP MSV TE CC FIG601

FIGURE 601 DIMENSIONS

Valve Size DN 80 100 150 200 250 300
Height - HR - Open MM 512 590 788 930 1200 1390
- Closed MM 425 483 630 722 940 1080
Length – L MM 203 229 267 292 330 356

HR

2.20
 VALVES

SUREFLOW® METAL SEATED GATE VALVE

VALVES / METAL SEATED GATE VALVES

SHOULDERED END -PN35 - DN100 & DN150 NON RISING SPINDLE

DN100 & DN150 NON RISING SPINDLE

Code Size (MM) Description
VSDXX10201CH 100 100 SH END NR/SP MS VLV CC
VSDXX15201CH 150 150 SH END NR/SP MS VLV CC

DIMENSIONS
ØC DN Height Length Handwheel
A B ØC ØD ØE F G

100 400 230 275 122.2 114.3 17.5 24.5

150 490 270 275 175.1 166.1 17.5 38.5
A

B
ØE

G
ØD

2.21
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW® METAL SEATED GATE VALVE

VALVES / METAL SEATED GATE VALVES

FIGURE 400 INTERGAL BYPASS DN 375 - DN 900

INTERGAL BYPASS - PN16 - DN375-900

Code Size (MM) Description
VSDCC37400AB 375 375X80 FL MSV BYP B5 ACC FIG400
VSDCC45400AB 450 450X100 FL MSV BYP VLV B5 ACC
VSDCC45400CB 450 450X100 FL MSV BYP VLV B5 CC
VSDCC50400ABG 500 500X150 FL MSV BYP B5 ACC GBX
VSDCC50400CBG 500 500X150 FL MSV BYP B5 CC GBX
VSDCC60400ABG 600 600X150 FL MSV BYP B5 ACC GBX
VSDCC60400CBG 600 600X150 FL MSV BYP B5 CC GBX
VSDCC75400ABG 750 750 FL MSV B5 ACC BYP 12:1 GBX
VSDCC75400CBG 750 750 FL MSV B5 CC BYP 12:1 GBX
VSDCC90400ABG 900 900X200 MSV B5 ACC BYP GBX
VSDCC90400CBG 900 900X200 MSV B5 CC BYP GBX

INTERGAL BYPASS - PN35 - DN375-900

Code Size (MM) Description
VSDFF37400AB 375 375X80 FL MSV BYP B6 ACC
VSDFF37400CB 375 375X80 FL MSV BYP B6 CC
VSDFF45400AB 450 450x100 FL MSV BYP B6 ACC
VSDFF45400CB 450 450x100 FL MSV BYP B6 CC
VSDFF50400ABG 500 500X150 FL MSV BYP B6 ACC GBX
VSDFF50400CBG 500 500X150 FL MSV BYP B6 CC GBX
VSDFF60400ABG 600 600X150 FL MSV BYP B6 ACC GBX
VSDFF60400CBG 600 600X150 FL MSV BYP B6 CC GBX
VSDFF75400ABG 750 750 FL MSV BYP B6 ACC G/BX
VSDFF75400CBG 750 750 FL MSV BYP B6 CC G/BX
VSDFF90400ABG 900 900 FL MSV BYP B6 ACC G/BX
VSDFF90400CBG 900 900 FL MSV BYP B6 CC G/BX

DIMENSIONS
Valve DN 375 450 500 600 750 900
A Size DN 80 100 150 150 150 200
A MM 960 1145 1280 1460 2360 2600
B MM 635 665 780 860 995 1090
C MM 610 660 710 785 950 1100

2.22
VALVES

CHECK
VALVES
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW®

VALVES / CHECK VALVES

SWING CHECK VALVES

RESILIENT SEATED DN 100 & DN 150 FREE ACTING

FEATURES TECHNICAL DATA

SUPERCHECK Swing Check Valves are suitable for water and Size Range
wastewater applications. Used to prevent backflow within a DN 100 and DN 150
pipeline.
Allowable Operating Pressures
1600kPa
Maximum Temperature
40˚C
Minimum Flow
Disc fully open–1.4m/s
End Connections
Flanged to AS 4087 Fig B5
Standards
AS 4794 Non-return valves
– Swing check and tilting disc
Certifications
AS/NZS 4020 Testing of products for use in contact with drinking
water

DN100 & DN150 FREE ACTING

Code Size (MM) Description
VCDCC10701 100 100 RS CHECK VLV B5 F/A FC
VCDCC15701 150 150 RS CHECK VLV B5 F/A FC

DIMENSIONS
Nom. Size Length Width Height
DN MM MM MM

100 330 215 254

150 410 329 343

Conforms to AS4794

2.24
 VALVES

SUREFLOW® SWING CHECK VALVES

VALVES / CHECK VALVES

RESILIENT SEATED DN 100 & DN 150 COUNTERWEIGHT

DN100 & DN150 COUNTERWEIGHT

Code Size (MM) Description
VCDCC10702 100 100 RS CHECK VLV B5 CWT FC
VCDCC15702 150 150 RS CHECK VLV B5 CWT FC

DIMENSIONS
Nom. Size Length Width Height
DN MM MM MM

100 330 269 254

150 410 340 343

Conforms to AS4794

2.25
 VIADUX WATER NETWORK SOLUTIONS

RSSC SWING CHECK VALVES

VALVES / CHECK VALVES

RESILIENT SEATED SWING CHECK VALVE ACCORDING TO AS4794

FEATURES TECHNICAL DATA

Idea for use on water and sewerage. Size Range

Designed to prevent backflow in horizontal or vertical pipelines. DN80 - DN375
Angled disc seat holds the disc open avoiding fluctuations. Pressure Classes
Designed and tested in accordance with AS4794. PN16

Body and bonnet are made of high grade ductile iron to AS1831. Face to Face
According to AS4794
Fusion Bonded Epoxy coating to AS4158 internally and externally
providing longer life and excellent corrosion resistance. Temperature Range
Full bore design gives non-clogging performance and reduces 0˚C to 60˚C
head loss.
Flange Connection
The NBR encapsulated disc prevents corrosion and provides drip AS4087 B5 (Table D)
tight closure with long life.
Coating
Extended shaft design allows installation of limit switches and
counterweight. AS4158
Bonnet allows for easy access for cleaning and maintenance
without having to remove valve from pipeline.
Certifications
Lifting lugs and support feet for easy handling.
Approved: According to: AS4794
Applicable to water & waste water applications - desalination,
pumping, industrial processing, irrigation and general industries.
Options
Alternative flange connections available on request.
With or without lever & weight.
Open/closed mechanical switches
No flow proximity sensors

2.26
 VALVES

RSSC SWING CHECK VALVES

VALVES / CHECK VALVES

RESILIENT SEATED SWING CHECK VALVE ACCORDING TO AS4794

DIMENSIONS (MM)
RSSC DN 80 – DN 375
Weight
DN FxF B B1 ØD ØD1 ØD2 N-ØD1 (KG)
80 260 18 3 185 146 122 4-18 20
100 330 20 3 215 178 154 4-18 28
150 410 23 3 280 235 211 8-18 56
ØD2

200 540 23 3 335 292 268 8-18 92

DN

ØD

250 640 24 3 405 356 328 8-22 164

300 700 30 4 455 406 378 12-22 242
375 820 34 4 550 495 463 12-26 410

b
Conforms to AS4794
b1
FxF

ØD1

n-Ød1

2.27
 VIADUX WATER NETWORK SOLUTIONS

RSFC SWING CHECK VALVES

VALVES / CHECK VALVES

NON SLAM RESILIENT SEATED CHECK VALVE ACCORDING TO AS 4794

FEATURES TECHNICAL DATA

Non slam. Size Range

100% sealing. DN80-DN600
Non clogging. Pressure Classes
Lower power consumption due to PN16
lower headloss. Face to Face
Will not flutter like traditional swing According to AS4794 (excluding 500mm)
check valves.
Temperature Range
One moulded part (no maintenance).
1˚C to +80˚ (higher on request)
No counterweight needed.
Flange Connection
Meets AS4794 (material & dimensional standards). AS4087, Class 16
Pressure Testing
Certifications
To AS4794
Approved: AS4020 According to: AS4794
Coating
AS4020 approved epoxy.

FLANGED - PN16 – DN80 - DN600

Code Size (MM) Description
RSFC VCAVF080FA 80 80MM PN16 F/A REFLUX VALVE
NON SLAM RESILIENT SEATED VCAVF100FA 100 100MM PN16 F/A REFLUX VALVE
CHECK VALVE ACCORDING TO AS4794
VCAVF150FA 150 150MM PN16 F/A REFLUX VALVE
VCAVF200FA 200 200MM PN16 F/A REFLUX VALVE
PARTS LIST VCAVF225FA 225 225MM PN16 F/A REFLUX VALVE

DETAIL VIEW A
VCAVF250FA 250 250MM PN16 F/A REFLUX VALVE
GGG50) VCAVF300FA 300 300MM PN16 F/A REFLUX VALVE
M (Standard) EPDM VCAVF375FA 375 375MM PN16 F/A REFLUX VALVE
(On Request)
STAINLESS VCAVF400FA 400 400MM PN16 F/A REFLUX VALVE
STEEL
VCAVF450FA 450 450MM PN16 F/A REFLUX VALVE
GGG50)
VCAVF500FA 500 500MM PN16 F/A REFLUX VALVE
NYLON VCAVF600FA 600 600MM PN16 F/A REFLUX VALVE
REINFORCED

WCB

DIMENSIONS (MM)
A RSFC DN 50 – DN 600
Weight
Weight
DN FxF B B1 ØD ØD1 ØD2 N-ØD1 (KG)
ØD2 n-Ød1
(Kg)
80 260 18 3 185 146 122 4-18 15
122 4-18 15
100 330 20 3 215 178 154 4-18 21
154 4-18 21
150 410 23 3 280 235 211 8-18 40
211 8-18 40
268 8-18 76
200 540 23 3 335 292 268 8-18 76
225 610 24 3 370 324 300 8-18 93
ØD2

ØD1

300 8-18 93
DN

ØD

328 8-22 122 250 640 24 3 405 356 328 8-22 122
378 12-22 218 300 700 30 4 455 406 378 12-22 218
463 12-26 247 375 820 33 4 550 495 463 12-26 247
489 12-26 311 400 914 33 4 580 521 489 12-26 311
552 12-26 416 450 970 33 4 640 584 552 12-26 416
n-Ød1

b
609 16-26 520
b1 500 978 35 4 705 641 609 16-26 520
720 16-30 790
FxF 600 1220 42 5 825 756 720 16-30 790
Conforms to AS4794

2.28
50

65

80

DN 0
5

0
10

15

20

25

30
37

45

50

60
DN

DN

DN

DN

DN

DN

DN

DN

DN

DN

DN
 VALVES

ACB-100 SERIES BALL CHECK VALVES

VALVES / CHECK VALVES

DN 32 – DN 500 BALL CHECK VALVE DUCTILE IRON PN 16 SUITABLE FOR DUCTILE IRON BODY

TECHNICAL DATA TECHNICAL DATA

Size Range
ACB-100
Flange Drilling
SERIES
DN50-DN500 (Flanged) BALL CHECK
AS4087 CL16 VALVE
DN32-DN65 (Threaded) DUCTILE IRON PN16
Leakage Tests
Pressure Classes DN32 - DN500
EN12266
PN16
Coating
Face to Face Fusion Bonded Epoxy
EN-558-1 series 48 (DIN3202 F6)
Minimum Backpressure
Temperature Range 0.3-0.5bar
10˚C to +80˚C
Threaded Connection:
BSP

ACB-100 SERIES
BALL CHECK VALVE
FLANGED - PN16 – DN80 - DN500
DUCTILE IRON PN16
DN32 - DN500 Code Size (MM) Description
VCBAVF050 50 50 BALL CHECK FL B5 DI FC
VCBAVF065 65 65 BALL CHECK FL B5 DI FC
VCBAVF080 80 80 BALL CHECK FL B5 DI FC
VCBAVF100 100 100 BALL CHECK FL B5 DI FC
VCBAVF125 125 125 BALL CHECK FL B5 DI FC
VCBAVF150 150 150 BALL CHECK FL B5 DI FC
VCBAVF200 200 200 BALL CHECK FL B5 DI FC
VCBAVF250 250 250 BALL CHECK FL B5 DI FC
Flanged Connection
VCBAVF300 300 300 BALL CHECK FL B5 DI FC
VCBAVF350 350 350 BALL CHECK FL B5 DI FC
FLANGED CONNECTION
VCBAVF400 400 400 BALL CHECK FL B5 DI FC
THREADED CONNECTION (BSP)

VCBAVF500 500 500 BALL CHECK FL B5 DI FC

page 1

THREADED - PN16 – DN32 - DN65

FEATURES TECHNICAL DATA
Code Size (MM) Description
• Full bore ductile iron body. Size Range: DN50 - DN500 (Flanged)
VCBAVF032-BSP 32 32 BALL
DN32 toCHECK
DN65 BSP DI FC
(Threaded)
• Higher pressure rating compared to other ball checks.
• Self-cleaning sinking type silent nitrile coated ball. VCBAVF040-BSP
Pressure Classes: 40 40 BALL CHECK BSP DI FC
PN16
• Inside and outside epoxy-coating. VCBAVF050-BSP 50 50 BALL CHECK
• Low pressure drop. Face to face: EN-558-1 seriesBSP
48 DI FC
(DIN3202 F6)
Threaded Connection (BSP) VCBAVF065-BSP 65 65 BALL CHECK BSP DI FC
• Removable bonnet for cleaning or changing the ball without Temperature Range: 10˚C to +80˚C
disassembly out of the pipeline.
Threaded Connection: BSP
• Horizontal and vertical installation
THREADEDin the pipeline.
CONNECTION (BSP)
• Light weight design for easy installation. Flange Drilling: AS4087 CL16
page 1

Leakage Tests: EN 12266

OPTIONS Coating: Fusion Bonded Epoxy
• Other flange connections. Minimum Backpressure: 0.3 - 0.5bar
• Size above 500mm available.
• 2.29
Various ball types including floating type ball.
TECHNICAL DATA
 VIADUX WATER NETWORK SOLUTIONS

ACB-100 SERIES BALL CHECK VALVES

VALVES / CHECK VALVES

DN 32 – DN 500 BALL CHECK VALVE DUCTILE IRON PN 16 SUITABLE FOR DUCTILE IRON BODY

DIMENSIONS (MM)

DN 50 – DN 150 ACB-100 SERIES FLANGED CONNECTION

Weight
DN FxF b h1 ØD ØD1 ØD2 n-Ød1 (KG)

ACB-100 SERIES n-Ød1 50 200 19 100 165 114 90 4-18 6.5

65 240 19 125 185 127 103 4-18 11
BALL CHECK VALVE
DUCTILE IRON PN16 80 260 19 136 200 146 122 4-18 14.35
DN32 - DN500 100 300 20 185 220 178 154 4-18 19.98
125 350 20 196 250 210 186 8-18 30.4
150 400 23 265 285 235 207 8-18 42.3
200 500 23 340 340 292 264 8-18 73.5
MOUNTING IN PIPELINE 250 600 24 420 405 356 328 8-22 128
300 700 30 480 460 406 374 12-22 180
FIGURE 1.DN 200 – DNINSTALLATION
HORIZONTAL 500 FIGURE 2. VERTICAL INSTALLATION
350 800 33 580 505 470 438 12-26 290
400 900 33 730 580 521 490 12-26 420
500 1100 33 900 705 641 609 16-26 580

ACB-100 SERIES THREADED CONNECTION

DN FxF h1 ØD Weight (KG)

32 135 72 50 2

FIGURE 4.
40 145 85 60 2
THREADED CONNECTION 50 175 100 70 3
65 200 125 90 5
MATERIAL SPECIFICATIONS & PARTS LIST
h1

NO. DESCRIPTION MATERIAL

1 Body Ductile Iron
ØD2

2 Bonnet Ductile Iron

3 Ball Steel & NBR (standard)
Steel & EPDM (optional)
4 Bonnet Gasket NBR (standard)
FxF
EPDM (optional)
page 2

h1

5 Bolts Stainless Steel

DN 32 – DN 65
ØD2

ØD1

ØD

DIMENSIONS (MM)

ABC-1000 SERIES FLANGED CONNECTION

DN FxF b h1 ØD ØD1 ØD2 n-Ød1 Weight (kg)

50 200 19 100 165 114 90 4-18 6.5

65 240 19 125 185 127 103 4-18 11 b

80 260 19 136 200 146 122 4-18 14.35 FxF

100 300 20 185 220 178 154 4-18 19.98
125 350 20 196 250 210 186 8-18 30.4 DN50 - DN150 DN200 - DN500
150 400 23 265 285 235 207 8-18 42.3
200 500 23 340 340 292 264 8-18 73.5
250 600 24 420 405 356 328 8-22 128 n-Ød1
300 700 30 480 460 406 374 12-22 180
350 800 33 580 505 470 438 12-26 290 2.30
400 900 33 730 580 521 490 12-26 420
 VALVES

AC10 DUO CHECK WAFER VALVE

VALVES / CHECK VALVES

DN 50 – DN 1000

FEATURES TECHNICAL DATA

Body (optional carbon steel, ductile iron Size Range

or duplex). DN40-DN1000
Disc (optional carbon steel, ductile iron Pressure Classes PN10, PN16, PN25
or duplex).
Face to Face
Upper and lower PTFE thrust bearings. DIN3202-K3
Standard EPDM Sealing O-Ring (optional NBR or Viton). Temperature Range
-20˚C to +100˚C (standard EPDM seat)
Dual springs for quicker activation long life and even distribution
-20˚C to +80˚C (optional NBR seat)
of force over
-20˚C to +150˚C (optional Viton seat)
both plates.
10 Fusion bonded epoxy coated body (internal & external).
Pressure Testing
AP1598
Long leaf springs (prevent rubbing of disc on seat). Coating
HECK WAFER VALVE
Fusion Bonded Epoxy
DN1000

PN16 – DN50 - DN800

Code Size (MM) Description
VCWDAVF050 50 50 DUO CHECK CI FC
VCWDAVF065 65 65 DUO CHECK CI FC
VCWDAVF080 80 80 DUO CHECK CI FC
VCWDAVF100 100 100 DUO CHECK CI FC
VCWDAVF125 125 125 DUO CHECK CI FC
VCWDAVF150 150 150 DUO CHECK CI FC
VCWDAVF200 200 200 DUO CHECK CI FC
VCWDAVF250 250 250 DUO CHECK CI FC
VCWDAVF300 300 300 DUO CHECK CI FC
VCWDAVF350 350 350 DUO CHECK CI FC
VCWDAVF400 400 400 DUO CHECK CI FC
VCWDAVF450 450 450 DUO CHECK CI FC
VCWDAVF500 500 500 DUO CHECK CI FC
VCWDAVF600 600 600 DUO CHECK CI FC
VCWDAVF700 700 700 DUO CHECK CI FC
VCWDAVF800 800 800 DUO CHECK CI FC

DN600 - DN800
SECTION A - A

2.31
ØD
 VIADUX WATER NETWORK SOLUTIONS

AC10 DUO CHECK WAFER VALVE

VALVES / CHECK VALVES

DN 50 – DN 1000

DIMENSIONS (MM)
DN50 - DN500 SECTION A - A
AB10 DN 50 – DN 800
ØD
ØD Weight
ØD1 DN ØD1
FxF ØD ØD1 ØD2 R (KG)

50 43 96 65 40 27 1.3

R 65 R 46 110 80 60 35 2.1
FxF

F xF
80 64 128 94 70 42 2.9
100 64 156 117 88 50 4.3
D2 125 70D2 187 145 115 64 6.4
150 76 ØD 213 171 134 77 9.1
ØD
DN600 - DN800 SECTION A - A 200 89ØD1 267 224 182 102.5 15.2
ØD1
250 114 328 265 220 125 26.5
ØD
D 300
R 114 375 310 260 146 37
R ØD1
D1
FxF

350 127 444 360 298 170 55

Fx F
400 140 495 410 350 195 80
R
D2 450 152 558 450 385 215 101
FxF

D2
Fx F

A A A 500 152 615 505 A 438 238 114

600 178 723 624.5 573 292 172
D2 D2 700 229 812 720 680 350 258
800 241 948 825 770 400 322

ØD
ØD A A A A
ØD1 ØD1

R R
A A A
FxF

Fx F

D2 D2

A A A

2.32
VALVES

BUTTERFLY
VALVES
VIADUX WATER NETWORK SOLUTIONS

VALVES / BUTTERFLY VALVES

2.34
 VALVES

AB SERIES BUTTERFLY VALVES

VALVES / BUTTERFLY VALVES

DN 50 & DN 1200 AVFI’S AB SERIES BUTTERFLY VALVES ARE SUITABLE FOR MOST GENERAL PURPOSE APPLICATIONS

FEATURES

Designed and manufactured to AS4795

Phenolically backed replaceable liner.
Rated to 1600kpa from 50mm up to 600mm
and 1000kpa from 700mm up to 1200mm.
Stainless steel fasteners.
Bi-directional bubble-tight sealing, with no
leakage under pressure.
ISO top mounting flange for easy actuation.
Gearbox fitted as standard on all sizes
350mm and above.
Certifications
According to: AS4795, API609, MSS SP67,
ISO5752, EN1092
Approved to WaterMark approval for AB30W
& AB30L only (Refer pages 3.78 & 3.81)

TECHNICAL DATA

Size Range
DN50-DN1200
Pressure Classes
PN10, PN16, PN21 & PN25
LEVER OPERATED – PN16 – DN50 - DN300 Face to Face
Code Size (MM) Description According to AS4795

VBWAVF050L 50 50 WAFER BFLY VLV T/D&E LEVER Top Flange

VBWAVF065L 65 65 WAFER BFLY VLV T/D&E LEVER According to ISO 5211

VBWAVF080L 80 80 WAFER BFLY VLV T/D&E LEVER Temperature Range

VBWAVF100L 100 100 WAFER BFLY VLV T/D&E LEVER -20˚C to +150˚C (depending on material)

VBWAVF125L 125 125 WAFER BFLY VLV T/D&E LEVER Leakage Tests:
VBWAVF150L 150 150 WAFER BFLY VLV T/D&E LEVER According to AS4795

VBWAVF200L 200 200 WAFER BFLY VLV T/D&E LEVER Coating

VBWAVF250L 250 250 WAFER BFLY VLV T/D&E LEVER Fusion Bonded Epoxy (for all cast and
ductile iron bodied valves)
VBWAVF300L 300 300 WAFER BFLY VLV T/D&E LEVER

GEARBOX OPERATED – PN16 – DN50 - DN300

Code Size (MM) Description
VBWAVF080GB 80 80 WAFER BFLY VLV T/E GBX
VBWAVF100GB 100 100 WAFER BFLY VLV T/E GBX
VBWAVF150GB 150 150 WAFER BFLY VLV T/E GBX
VBWAVF200GB 200 200 WAFER BFLY VLV T/E GBX
VBWAVF250GB 250 250 WAFER BFLY VLV T/E GBX
VBWAVF300GB 300 300 WAFER BFLY VLV T/E GBX

2.35
 WAFER TYPE BUTTERFLY VALVE
AB30
AB 30WW
WATERMARK
WATERMARK APPROVED
APPROVED
VIADUX WATER NETWORK SOLUTIONS
WAFER
WAFER TYPE
TYPE BUTTERFLY
BUTTERFLY VALVE
VALVE

AB30W WAFER TYPE BUTTERFLY VALVE

VALVES / BUTTERFLY VALVES

BUTTERFLY VALVE FOR DN 50 – DN 300

Nominal Pressure PN16

DN50
DN50 -- DN80
DN80 DN100
DN100 -- DN300
DN300 Test: Strength Test 24 Bar
ØM Pressure: Sealing Test 17.6 Bar
ØM
n-Øm n-Øm
DN50 - DN80 DN100 - DN300 Max Working Temperature: -25° to +100°C
DN50 - DN80 DN100 - DN300
n-Øm

45 °
45°

Suitable Media W.O.G etc

ØM
ØM
ØM
ØM
n-ØmØM1 n-Øm
n-Øm Note: PN21 & PN25, dimensions available on
n-Øm request. Designed and manufactured to AS4795.
ØM1 ØM2 ØM2
n-Øm
454°5
454°5

n-Øm M3 ØM1 M3
°
°

ØM1
ØM1
SECTION A - A A
ØM1 ØM2 ØM2
ØM2
ØM1 ØM2
M3
M3 ØM1
ØM1 M3
M3
h3

SECTION A - A AA
SECTION A - A
h3h3

n-Ød1
ØD1
h2

n-Ød1
n-Ød1
ØD1
ØD1
h2h2
ØD2
DN
E2

h1
ØD2
DNDN
E2E2

ØD2

E1
A
Fx F
h1
h1

E1E1
AA
FxFxFF

DIMENSIONS (MM)
WAFER TYPE BFLY AS2129 T/D AS2129 AS2129 ANSI150 ISO 5211
DN 50 – DN 300 AS2129 T/E T/D T/E MM TOP FLANGE
Flange Weight
DN FxF h1 h2 h3 E1 E2 ØD2 80 220 288 145 17 No. ØM n-Øm ØM1 ØM2 M3 (KG)

50 43 57 143 29 3.2 25.1 77 114 4-18 4-18 120.6 4-19 F05/F07 90 4-8/4-10 50/70 35.5 11x11 3.66
65 46 68 155 29 7.6 41.1 89 127 4-18 4-18 139.7 4-19 F05/F07 90 4-8/4-10 50/70 35.5 11x11 4.28
80 46 82 160 29 14.9 61.8 104 146 4-18 4-18 152.4 4-19 F05/F07 90 4-8/4-10 50/70 35.5 11x11 4.6
100 52 100 181 29 25.1 89.1 135 178 4-18 8-18 190.5 8-19 F07 90 4-10 70 55.5 11x11 5.8
125 56 112 194 29 32.6 108.7 159 210 8-18 8-18 215.9 8-22.4 F07 90 4-10 70 55.5 14x14 8
150 56 126 202 29 48.9 144.6 189 235 8-18 8-22 241.3 8-22.4 F07 90 4-10 70 55.5 14x14 9.5
200 60 162 240 35 70 192.5 239 292 8-18 8-22 298.4 8-22.4 F10 125 4-12 102 70.5 17x17 16
250 68 193 272 35 90.3 240.5 293 356 8-22 12-22 361.9 12-25.4 F10 125 4-12 102 70.5 22x22 21
300 78 236.5 318 35 111 290.8 345 406 12-22 12-26 431.8 12-25.4 F10 125 4-12 102 70.5 22x22 35

2.36
 VALVES

AB10W WAFER TYPE BUTTERFLY VALVE

VALVES / BUTTERFLY VALVES

DN 350 – DN 600 SUITABLE FOR PN 10 OR PN 16

GEARBOX OPERATED – PN10 – DN350 - DN600

Code Size (MM) Description
VBWAVF350GBPN10 350 350 WAFER BFLY VLV PN10 T/D&E/ANSI GBX
VBWAVF400GBPN10 400 400 WAFER BFLY VLV PN10 T/D&E/ANSI GBX
VBWAVF450GBPN10 450 450 WAFER BFLY VLV PN10 T/D&E/ANSI GBX
VBWAVF500GBPN10 500 500 WAFER BFLY VLV PN10 T/D&E/ANSI GBX
VBWAVF600GBPN10 600 600 WAFER BFLY VLV PN10 T/D&E GBX

GEARBOX OPERATED – PN16 – DN350 - DN600

Code Size (MM) Description
VBWAVF350GB 350 350 WAFER BFLY VLV PN16 T/D&E/ANSI GBX
VBWAVF400GB 400 400 WAFER BFLY VLV PN16 T/D&E/ANSI GBX
VBWAVF450GB 450 450 WAFER BFLY VLV PN16 T/D&E/ANSI GBX
VBWAVF500GB 500 500 WAFER BFLY VLV PN16 T/D&E/ANSI GBX
VBWAVF600GB 600 600 WAFER BFLY VLV PN16 T/D&E GBX

2.37
 VIADUX WATER NETWORK SOLUTIONS

AB10W WAFER TYPE BUTTERFLY VALVE

VALVES / BUTTERFLY VALVES

DN 350 – DN 600 SUITABLE FOR PN 10 OR PN 16

Nominal Pressure PN10 PN16

DN350 DN350
- DN600
- DN600 KEYWAY
KEYWAY
DN350 DN350 KEYWAY
KEYWAY
DN400 DN400
- DN600
- DN600
Test: Strength Test 15 Bar 24 Bar
ØM ØM
L3

L3
n-Øm n-Øm Pressure: Sealing Test 11 Bar 17.6 Bar

L3

L3
DN350
DN350 -- DN600
DN600 KEYWAY
KEYWAY DN350
DN350 KEYWAY
KEYWAY DN400
DN400 -- DN600
DN600
SECTION
SECTION
B-B B-B
B B Max Working Temperature: -20° to +100°C
45°

45°

ØM
ØM
L2 L2 11 11 L2 L2
L3

n-Øm
n-Øm Suitable Media W.O.G etc

L3
SECTION
SECTION B
B -- B
B
BB
45°

ØM2 ØM2
L2 Note: PN21 & PN25, dimensions available on
22

22

L2
L2 L2

L1

L1
28

28
request. Designed and manufactured to AS4795.
ØM1 ØM1
ØM3 ØM3
ØM2
ØM2 B B Key Key

L1
ØM1
ØM1
SECTION
SECTION A - A A - A ØM3
ØM3
BB Key
Key
A A
SECTION AA -- AA
SECTION KEYWAY
AA DN L1 L2 L3
h4

h4

h3

h3

350 22 8 8
400 45 10 5
h4

h3

2 2 450 45 10 5

1 1 n-Ød1 n-Ød1 500 56 10 5

ØD1 ØD1 600 58 16 6

h2

h2

3 3 n-Ød1
n-Ød1
ØD1
ØD1
h2

4 4

5 5
ØD2

ØD2
DN

DN
E2

E2

6 6
ØD2
DN
E2

h1

h1

7 7
h1

E1 E1
FxF FxF A A
E1
E1
FxF
FxF AA

DIMENSIONS (MM)
WAFER TYPE BFLY AS2129 T/D AS2129 AS2129 ANSI150 ISO 5211
DN 350 – DN 600 AS2129 T/E T/D T/E MM TOP FLANGE
Flange Weight
DN FxF h1 h2 h3 E1 E2 ØD2 ØD1 n-Ød1 n-Ød1 ØD1 n-Ød1 No. ØM n-Øm ØM1 ØM2 ØM3 h4 (KG)

350 78 267 368 45 126.9 323.7 376 470 12-26 12-26 476.2 12-28.4 F10 125 4-12 102 70.5 31.6 3.5 58
400 102 299 400 51.2 149.7 378.8 440 521 12-26 12-26 539.7 16-28.4 F14 175 4-18 140 100.5 33.15 4.5 107
450 114 318 422 51.2 166 427.3 491 584 12-26 16-26 577.8 16-31.8 F14 175 4-18 140 100.5 38 4.5 122
500 127 355 480 64.2 178.4 472.8 536 641 16-26 16-26 635 20-31.8 F14 175 4-18 140 100.5 41.15 4.5 160
600 154 444 562 70.2 218.4 571.9 655 756 16-30 16-33 749.3 20-35.1 F16 210 4-22 165 130.5 50.65 5.5 260

2.38
 VALVES

AB30L LUGGED TYPE BUTTERFLY VALVE

VALVES / BUTTERFLY VALVES

DN 50 – DN 300 WATERMARK APPROVED TABLE E LUGGED TYPE BUTTERFLY VALVE

LEVER OPERATED – PN16 – DN50 - DN300

Code Size (MM) Description
VBLAVF050L 50 50 LUGGED BFLY VLV T/D&E LEVER
VBLAVF065L 65 65 LUGGED BFLY VLV T/D&E LEVER
VBLAVF080L 80 80 LUGGED BFLY VLV T/D&E LEVER
VBLAVF100L 100 100 LUGGED BFLY VLV T/D LEVER
VBLAVF125L 125 125 LUGGED BFLY VLV T/D&E LEVER
VBLAVF150L 150 150 LUGGED BFLY VLV T/D LEVER
VBLAVF200L 200 200 LUGGED BFLY VLV T/D LEVER
VBLAVF250L 250 250 LUGGED BFLY VLV T/D LEVER
VBLAVF300L 300 300 LUGGED BFLY VLV T/D LEVER

GEARBOX OPERATED – PN16 – DN80 - DN300

Code Size (MM) Description
VBLAVF080GB 80 80 LUGGED BFLY VLV T/D&E GBX
VBLAVF100GB 100 100 LUGGED BFLY VLV T/D GBX
VBLAVF150GB 150 150 LUGGED BFLY VLV T/D GBX
VBLAVF200GB 200 200 LUGGED BFLY VLV T/D GBX
VBLAVF250GB 250 250 LUGGED BFLY VLV T/D GBX
VBLAVF300GB 300 300 LUGGED BFLY VLV T/D GBX

2.39
 VIADUX WATER NETWORK SOLUTIONS

AB30L LUGGED TYPE BUTTERFLY VALVE

VALVES / BUTTERFLY VALVES

DN 350 – DN 600 SUITABLE FOR PN 10 OR PN 16

Nominal Pressure PN16

DN50 - DN80 DN100 - DN300
DN50 - DN80 DN100 - DN300 Test: Strength Test 24 Bar
ØM
ØM Pressure: Sealing Test 17.6 Bar
n-Øm n-Øm
Max Working Temperature: -20° to +100°C
n-Øm

45°
45°

DN50 - DN80 DN50 - DN80 DN100 - DN300

DN100 - DN300 Suitable Media W.O.G etc
ØM ØM
ØM ØM ØM1
n-Øm n-Øm n-Øm n-Øm Note: PN21 & PN25, dimensions available on
ØM1 ØM2 ØM2 request. Designed and manufactured to AS4795.
n-Øm n-Øm M3
45 °
45°

ØM1
45°
45°

M3
ØM1 ØM1 SECTION A - A A
ØM1 ØM1 ØM2 ØM2 ØM2 ØM2
M3 M3 ØM1 ØM1 M3
7 M3
h3

2
SECTION A - ASECTION A-A A A

7 1 n-Ød1
h3
h3

ØD1
2
h2

3
1 n-Ød1 n-Ød1
4 ØD1 ØD1
h2
h2

3
ØD2
DN
E2

4 6
h1
ØD2
ØD2

DN
DN

E2
E2

5
E1
6 A
h1
h1

FxF

E1 E1
Fx F FxF A A

DIMENSIONS (MM)
LUGGED TYPE BFLY AS2129 TABLE ISO 5211
DN 50 – DN 300 D/E (MM) TOP FLANGE
Flange Weight
DN FxF h1 h2 h3 E1 E2 ØD2 ØD1 n-ØD1 No. ØM n-Øm ØM1 ØM2 M3 (KG)

50 43 57 143 29 3.2 25.1 77 114 4-M16 F05/F07 90 4-8/4-10 50/70 35.5 11x11 4.5
65 46 68 155 29 7.6 41.4 89 127 4-M16 F05/F07 90 4-8/4-10 50/70 35.5 11x11 5
80 46 82 160 29 14.9 61.8 104 146 4-M16 F05/F07 90 4-8/4-10 50/70 35.5 11x11 6.2
100 52 100 181 29 25.1 89.1 135 178 8-M16 F07 90 4-10 70 55.5 11x11 9.2
125 56 112 194 29 32.6 108.7 159 210 8-M16 F07 90 4-10 70 55.5 14x14 11.6
150 56 126 202 29 48.9 144.6 189 235 8-M20 F07 90 4-10 70 55.5 14x14 13.2
200 60 162 240 35 70 192.5 239 292 8-M20 F10 125 4-12 102 70.5 17x17 21
250 68 193 272 35 90.3 240.5 293 356 12-M20 F10 125 4-12 102 70.5 22x22 31
300 78 236.5 318 35 111 290.8 345 406 12-M24 F10 125 4-12 102 70.5 22x22 46.4

2.40
 VALVES

AB10L LUGGED TYPE BUTTERFLY VALVE

VALVES / BUTTERFLY VALVES

DN 350 – DN 600 TABLE E LUGGED TYPE BUTTERFLY VALVE SUITABLE FOR PN 10 OR PN 16

GEARBOX OPERATED – PN10 – DN350 - DN600

Code Size (MM) Description
VBLAVF350GBPN10 350 350 LUGGED BFLY VLV PN10 T/D&E GBX
VBLAVF400GBPN10 400 400 LUGGED BFLY VLV PN10 T/D&E GBX
VBLAVF450GBPN10 450 450 LUGGED BFLY VLV PN10 T/D GBX
VBLAVF500GBPN10 500 500 LUGGED BFLY VLV PN10 T/D&E GBX
VBLAVF600GBPN10 600 600 LUGGED BFLY VLV PN10 T/D GBX

GEARBOX OPERATED – PN16 – DN350 - DN600

Code Size (MM) Description
VBLAVF350GB 350 350 LUGGED BFLY VLV PN16 T/D&E GBX
VBLAVF400GB 400 400 LUGGED BFLY VLV PN16 T/D&E GBX
VBLAVF450GB 450 450 LUGGED BFLY VLV PN16 T/D GBX
VBLAVF500GB 500 500 LUGGED BFLY VLV PN16 T/D&E GBX
VBLAVF600GB 600 600 LUGGED BFLY VLV PN16 T/D GBX

2.41
 VIADUX WATER NETWORK SOLUTIONS

AB10L LUGGED TYPE BUTTERFLY VALVE

VALVES / BUTTERFLY VALVES

DN 350 – DN 600 TABLE E LUGGED TYPE BUTTERFLY VALVE SUITABLE FOR PN 10 OR PN 16

Nominal Pressure PN10 PN16

KEYWAY DN350
KEYWAY DN350 KEYWAY KEYWAY
DN350 - DN600
DN350 - DN600 Test: Strength Test 15 Bar 24 Bar
DN400 - DN600
DN400 - DN600
ØM ØM KEYWAY
L3

L3 KEYWAY DN350
DN350 - DN600 KEYWAY DN350 KEYWAY Pressure: Sealing Test 11 Bar 17.6 Bar
n-Øm n-Øm DN350 - DN600 DN400 - DN600

L3

L3
DN400 - DN600
SECTION B -SECTION
B B-B
ØMØM B B Max Working Temperature: -20° to +100°C
L3
L3
45°

45°

n-Øm

L3
n-Øm L2 L2 11 SECTION B11 - B L2 L2

L3
Suitable Media W.O.G etc
BB
SECTION B - B
45°°
45

ØM2 ØM2 L2L2 11 11 L2 L2

Note: PN21 & PN25, dimensions available on
22

22

L1

L1
28

28 request. Designed and manufactured to AS4795.

ØM1 ØM1ØM2
22

ØM2 ØM3

L1
ØM3
22

28

L1
B B
Key Key
28

ØM1
ØM1 ØM3
ØM3 BB KeyKey
SECTION A -SECTION
A A-A
A A
SECTION A - A
SECTION A - A
AA
h4

h4

h3

h3
h4

h3
h4

h3

2 2

1 12 n-Ød1 n-Ød1
ØD1 ØD1
h2

h2 h2

n-Ød1
n-Ød1
3 31
ØD1ØD1
h2

4 43

5 54
ØD2

ØD2 ØD2
DN

DN DN
E2

E2 E2

6 65
ØD2
DN
E2

h1

h1 h1

7 76
h1

7
E1 E1 A A
Fx F Fx F E1 E1 AA
FxFx
FF

DIMENSIONS (MM)
LUGGED TYPE BFLY AS2129 TABLE ISO 5211
DN 350 – DN 600 D/E (MM) TOP FLANGE KEYWAY
Flange Weight
DN FxF h1 h2 h3 E1 E2 ØD2 ØD1 n-Ød1 No. ØM n-Øm ØM1 ØM2 ØM3 h4 (KG) L1 L2 L3

350 78 267 368 45 126.9 323.7 376 470 12-M24 F10 125 4-12 102 70.5 31.6 3.5 81 22 8 8
400 102 299 400 51.2 149.7 378.8 440 521 12-M24 F14 175 4-18 140 100.5 33.15 4.5 140 45 10 5
450 114 318 422 51.2 166 427.3 491 584 16-M24 F14 175 4-18 140 100.5 38 4.5 176 45 10 5
500 127 348 480 64.2 178.4 472.8 536 641 16-M26 F14 175 4-18 140 100.5 41.15 4.5 226 56 10 5
600 154 444 562 70.2 218.4 571.9 655 756 16-M30 F16 210 4-22 165 130.5 50.65 5.5 336 58 16 6

2.42
 DOUBLE FLANG
DN50 - DN2000
VALVES

AB13F DOUBLE FLANGED BUTTERFLY VALVES

VALVES / BUTTERFLY VALVES

DN 50 – DN 2000

FEATURES

Designed and manufactured to AS4795.

Vulcanized liner resists deformation.
Rated to 1600kpa from 50mm up to 600mm
and 1000kpa from 700mm up to 1200mm.
316 Stainless steel fasteners.
Bi-directional bubble-tight sealing, with no
leakage under pressure.
ISO top mounting flange for easy actuation.
Gearbox fitted as standard on all sizes
200mm and above.

Certifications
According to: AS4795, API609, MSS SP67,
ISO5752, EN1092

TECHNICAL DATA
Lever Operated
Size Range
DN50-DN2000
LEVER OPERATED
Pressure Classes
LEVER OPERATED – PN16 – DN80 - DN300 PN10, PN16
Code Size (MM) Description Face to Face
VBFLAVF080L 80 80 DOUBLE FLANGED BFLY LEVER According to AS4795
FEATURES
VBFLAVF100L 100 100 DOUBLE FLANGED BFLY LEVER Top Flange ACCORDING T
According to ISO 5211
VBFLAVF125L 125 125 DOUBLE FLANGED BFLY LEVER
• Designed and150manufactured
VBFLAVF150L
to AS4795.
150 DOUBLE FLANGED BFLY LEVER
Flange Drilling AS4795
AS4087
• Vulcanized liner
VBFLAVF200L 200 resists200
deformation.
DOUBLE FLANGED BFLY LEVER
Temperature Range API609
• Rated to 1600kpa
VBFLAVF250L 250 from25050mm up toBFLY
DOUBLE FLANGED 600mm
LEVER and 1000kpa
-10˚C to +90˚C (EPDM standard)
from 700mm 300
VBFLAVF300L
up to 1200mm.
300 DOUBLE FLANGED BFLY LEVER Leakage Tests: MSS SP67
According to AS4795
• 316 Stainless steel fasteners.
Coating
• Bi-directional bubble-tight sealing, with no leakage Fusion Bonded Epoxy (AS4020 approved)
under pressure. TECHNICAL DA
• ISO top mounting flange for easy actuation.
• Gearbox fitted as standard on all sizes 200mm and above. Size Range:
Pressure Classes:
OPTIONS Face to face:
• Full stainless steel lever. Top Flange:
• Gearboxes available for valves 150mm and below.
•2.43Pneumatic and electric actuation. Flange Drilling:
 VIADUX WATER NETWORK SOLUTIONS

AB13F DOUBLE FLANGED BUTTERFLY VALVES

VALVES / BUTTERFLY VALVES

DN 50 – DN 2000

DN50 - DN80
DN50 - DN80 DN100 - DN300
DN100 - DN300
ØM ØM
ØM ØM
n-Øm n-Øm n-Øm n-Øm
DN50DN50
- DN80
- DN80 DN100 - DN300
DN100 - DN300
n-Øm n-Øm

45°

45°
45°

45°

ØM ØM
ØM ØM
n-Øm n-Øm
ØM1 n-Øm n-Øm
ØM1
ØM1 n-Øm n-Øm
ØM1 ØM1 ØM1
45°
45°
45°
45°

M3 M3
ØM1 ØM1 M3 M3
ØM1 ØM1 ØM1 ØM1
A M3 M3A - A
SECTION A -SECTION A A
M3 M3

A A
h3

h3
SECTION A-AA-A
SECTION
6 6 n-Ød1 n-Ød1
ØD ØD
h3
h3

ØD1 ØD1
64 n-Ød1 n-Ød1
4 ØD ØD
h2

h2

7 7 ØD1 ØD1
4
h2
h2

3 3
7
E2

E2
ØD2

ØD2

2 2
3
E1 E1
E2
E2
ØD2
ØD2

2
h1

h1

5 5
E1 E1
h1
h1

1 51
b1 b1 b b
1 Fx F Fx F A A
b1 b1 b b
Fx F Fx F A A

DIMENSIONS (MM)
AB13F AS4087 CL16 ISO 5211
DN 50 – DN 300 MM TOP FLANGE
Flange Weight
DN FxF b b1 h1 h2 h3 E1 E2 ØD ØD1 ØD2 n-Ød1 No. ØM n-Øm ØM1 M3 (KG)

50 108 17 3 80 110 29 - - 168.5 114 95 4-18 F05/F07 65/90 4-8 50/70 11x11 4.9
65 112 17 3 80 134 29 - - 188.5 127 114 4-18 F05/F07 65/90 4-8 50/70 11x11 8.2
80 114 17 3 95 131 29 - - 214 146 128 4-18 F05/F07 65/90 4-8 50/70 11x11 10.1
100 127 17 3 114 150 29 - - 224 178 150 4-18 F07 90 4-10 70 11x11 13.4
125 140 17.8 3 113 170 29 - - 250 210 180 8-18 F07 90 4-10 70 14x14 17.8
150 140 19 3 139 180 29 8.2 69.7 280 235 200 8-18 F07 90 4-10 70 14x14 21.5

Designed and manufactured to AS4795.

2.44
 VALVES

AB13F
DOUBLE FLANGED BUTTERFLY VALVES
DN50 - DN2000
AB13F DOUBLE FLANGED BUTTERFLY VALVES
VALVES / BUTTERFLY VALVES

DN 50 – DN 2000

Gearbox Operated

GEARBOX OPERATED

GEARBOX OPERATED – PN16 – DN80 - DN600

Code Size (MM) Description
ACCORDING80TO
VBFLAVF080GB 80 DOUBLE FLANGED BFLY GBX
VBFLAVF100GB 100 100 DOUBLE FLANGED BFLY GBX
AS4795 ISO5752
page 1

VBFLAVF125GB 125 125 DOUBLE FLANGED BFLY GBX

API609
VBFLAVF150GB 150 EN1092
150 DOUBLE FLANGED BFLY GBX
a VBFLAVF200GB 200 200 DOUBLE FLANGED BFLY GBX
MSS SP67
VBFLAVF250GB 250 250 DOUBLE FLANGED BFLY GBX
VBFLAVF300GB 300 300 DOUBLE FLANGED BFLY GBX
VBFLAVF350GB 350 350 DOUBLE FLANGED BFLY GBX

TECHNICAL DATA
VBFLAVF375GB 375 375 DOUBLE FLANGED BFLY GBX
VBFLAVF400GB 400 400 DOUBLE FLANGED BFLY GBX
e. Size Range:
VBFLAVF450GB 450
DN50 - DN2000
450 DOUBLE FLANGED BFLY GBX
Pressure Classes:
VBFLAVF500GB 500 PN10, PN16
500 DOUBLE FLANGED BFLY GBX
VBFLAVF600GB 600 600 DOUBLE FLANGED BFLY GBX
Face to face: According to AS4795
Top Flange: According to ISO 5211
Flange Drilling: AS4087
2.45
Temperature Range: -10˚C to +90˚C (EPDM standard)
 VIADUX WATER NETWORK SOLUTIONS

AB13F DOUBLE FLANGED BUTTERFLY VALVES

/ HYDRANT VALVES
DN 50 – DN 2000

/ BUTTERFLY
KEYWAY

VALVES
DN350 - DN600 DN350 - DN600 KEYWAY DN350 KEYWAY DN400 - DN600 KEYWAY DN400 - DN600
KEYWAY DN350
L1 L1 L1 ØW1 W2

VALVES
ØM ØM
L3

L3
-Øm n-Øm 12.7 5 5.5 19 7.5

L3

L3
SECTION B - B SECTION B - B
B B
45°

18 8 8 28 11
45°

L2 W2 L2 L2
W2 L2
22 8 8 28 11
DN350 - DN600 ØW1 KEYWAY DN350 ØW1 KEYWAY DN400 - DN600
M1 DN350
ØM1 - DN600
ØM KEYWAY DN350 KEYWAY DN400 - DN600 22 8 8 28 11
L1

L1
L3

Key

L1
Key

L1
ØM n-Øm 10 5 - -

L3
ØM3n-Øm 45
L3

ØM3 SECTION B - B

L3
SECTION
B B-B
4 5°

B B L2 B 45 10 5 - -
45°

W2 L2
SECTION A - A SECTION A - A L2 A W2 A L2
ØW1 45 10 5 - -
ØM1 ØW1
L1

Key 56 10 5 - -

L1
ØM1
L1

ØM3 Key L1
ØM3 58 16 6 - -
h3

h3

B
SECTION A - A B A
6 SECTION A - A n-Ød1 n-Ød1 AØD
ØD
ØD1 ØD1
h3

4
h2
h3

h2

n-Ød1
n-Ød1 ØD
6 7 ØD
ØD1
3 ØD1
h2
E2

E2
ØD2

4
ØD2

h2

2
7
E1 E1
h1

h1

3
E2
ØD2

5
E2
ØD2

2
1 E1
E1
h1

b1 b b1 b
h1

5 A A
Fx F FxF
1
b1 b
b1 A
Fx Fb A
Fx F

DIMENSIONS (MM)
AB13F AS4087 CL16 ISO 5211
DN 200 – DN 600 MM TOP FLANGE
Flange Weight
DN FxF b b1 h1 h2 h3 E1 E2 ØD ØD1 ØD2 n-Ød1 No. ØM n-Øm ØM1 ØM3 (KG)

200 152 20 3 175 210 35 25.5 134.4 340 292 262 8-18 F10 125 4-12 102 22.1 41

250 165 22 3 203 245 35 43.3 189.8 415 356 310 8-22 F10 125 4-12 102 28.5 53.5

300 178 23 4 242 276 35 61.8 243.4 457 406 364 12-22 F10 125 4-12 102 31.6 66.4

350 190 25 4 250 328 45 72 274.6 512 470 422 12-26 F10 125 4-12 102 31.6 84.8

375 190 29 4 265 350 51.2 82.5 305.3 550 495 450 12-26 F14 175 4-18 140 33.2 121.8

400 216 28 4 277.4 376 51.2 87.1 325 570 521 470 12-26 F14 175 4-18 140 33.2 121.8

450 222 30 4 295.2 406.6 51.2 109.6 381.3 620 584 520/538 12-26 F14 175 4-18 140 38 197.8

500 229 31.5 4 330 448 64.2 131.5 435.3 655 641 572/599 16-26 F14 175 4-18 140 41.2 279

600 267 36 4 418 518 70.2 163 529.5 790 756 672/710 16-30 F16 210 4-22 165 50.7 376.8

Designed and manufactured to AS4795.

2.46
VALVES

HYDRANT
VALVES
VIADUX WATER NETWORK SOLUTIONS

VALVES / HYDRANT VALVES

2.48
 VALVES

SUREFLOW® SPRING HYDRANT VALVES

VALVES / HYDRANT VALVES

DN 80 & DN 100

FEATURES

SUREFLOW Spring Hydrant Valves provide

direct access to water pipelines for fire
fighting purposes. Access is gained by
the attachment of a standpipe to the
hydrant lugs.
The hydrant valve can also be used as a
scouring or flushing point.

TECHNICAL DATA

Allowable Operating
Pressure 1600 kPa
Seat Infiltration Resistance
55 kPa (vacuum)
Maximum Temperature 60°C
End Connections
Flanged to AS 4087 Fig B5,
DN 80 and DN 100
Certification
ISC AS 3952:2002 Certified Product
Licence No. PRD/R61/0412
AS/NZS 4020
Testing of products for use in
contact with drinking water.

STANDARD HYDRANT VALVES – SUREFLOW SPRING

L

Code Size (MM) Weight (KG) Description

SHAC008S7K 80 8.5 80 SUREFLOW SPRING HYDRANT B5
SHAC010S7K 100 9.5 100 SUREFLOW SPRING HYDRANT B5

STANDARD HYDRANT VALVES – SUREFLOW LILAC SPRING H

Code Size (MM) Weight (KG) Description

SHAC008S7KL 80 8.5 80 SUREFLOW LILAC SPRING HYDRANT B5
SHAC010S7KL 100 9.5 100 SUREFLOW LILAC SPRING HYDRANT B5

Designed and manufactured to AS3952. L1

DIMENSIONS (MM)
Weight
DN H L L1 (KG)

80 268 214 154 9.2

100 268 214 166 10.3

2.49
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW® SPRING SWAB HYDRANT VALVES

VALVES / HYDRANT VALVES

DN 80 & DN 100

SWAB HYDRANT VALVES – SUREFLOW SPRING DIMENSIONS (MM)

Code Size (MM) Weight (KG) Description Weight
DN H L L1 (KG)
SHAC008S7KSWAB 80 8.5 80 SUREFLOW SWAB SPRING HYDRANT B5
80 268 218 185 12.45
SHAC010S7KSWAB 100 9.5 100 SUREFLOW SWAB SPRING HYDRANT B5
100 268 218 215 14.25

SWAB HYDRANT VALVES – SUREFLOW LILAC SPRING

Size Weight
Code Description
(MM) (KG)
SHAC008S7KSWABL 80 8.5 80 SUREFLOW SWAB LILAC SPRING HYDRANT B5
SHAC010S7KSWABL 100 9.5 100 SUREFLOW SWAB LILAC SPRING HYDRANT B5

Designed and manufactured to AS3952.

2.50
 VALVES

SUREFLOW® HYDRANT & AIR VALVE ISOLATORS

VALVES / HYDRANT VALVES

DN 80 & DN 100 PROVIDING ISOLATION OF ATTACHED APPURTENANCE FOR MAINTENANCE

FEATURES

Hydrant and Air Valve Isolators can

be used in conjunction with spring
hydrants, air valves or screwed outlets to
provide isolation of the appurtenance for
maintenance purposes.
Available outlet option include:
-Screwed Outlet
-Spring Hydrant
-Air Valve

TECHNICAL DATA

Size Range
DN 80 and DN 100
Allowable Operating Pressures
1600kPa or 3500kPa
Maximum Temperature
50˚C
End Connections
Flanged to AS 4087 Fig B5 or B6
Certifications
AS/NZS 4020
Testing of products for use in
contact with drinking water.

DN80 & DN100 – PN16

Code Size (MM) Description
VHDCC0808S7 80 80 B5/80 B5 CC H&AV ISOLATOR FC
VHDCC0808S7ACC 80 80 B5/80 B5 ACC H&AV ISOLATOR FC
VHDCC1010S7 100 100 B5/100 B5 CC H&AV ISOLATOR FC
FLANGED
AS 4087
VHDCC1010S7ACC 100 100 B5/100 B5 ACC H&AV ISOLATOR FC

DN80 & DN100 – PN35

Size
Code Description
(MM)
VHDFF0808S7 80 80 B6/80 B6 CC H&AV ISOLATOR FC
VHDFF1010S7 100 100 B6/100 B6 CC H&AV ISOLATOR FC FLANGED
AS 4087
DN 80

Designed and manufactured to AS3952.

2.51
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW HYDRANT & AIR VALVE ISOLATORS

VALVES / HYDRANT VALVES

BS750 UNDERGROUND FIRE HYDRANT – NORTHERN TERRITORY

FEATURES

NT Underground Fire Hydrants provide

direct access to water pipelines for fire
fighting purposes. Access is gained with
the attachment of a BS750 – 2 ½” x 2 TPI
threaded attachment.
Jumper valve for back flow prevention.
Slotted mounting holes to match Dn80
AS4087 FIG B5 and Dn90 AS2129 Table D
flanges.
Grade 316 stainless steel fasteners for long
life application.
Insulation essential for installations
subject to temperatures of 0˚C and lower.

TECHNICAL DATA

Allowable Operating Pressures

Seat: 16 bar
Body: 24 bar
Maximum Temperature
Valve designed for use up to 70˚C Where
applicable; for AS 4020 compliance, max
temp 50˚C
Note: Always observe pipe material
recommended operating temperatures
End Connections
Universally drilled AS 4087 Dn80
FIG B5/AS 2129 Dn90 Table D slotted holes

DN80 - PN16
Code Size (MM) Description
VHDCN0808S7P 80 80 B5 HYD ISOLATOR NT BS750 SCREW DOWN

Conforms to power and water corporation specification w02-s5 – screw down hydrant

2.52
 VALVES

SUREFLOW® HYDRANT & AIR VALVE ISOLATORS

VALVES / HYDRANT VALVES

DN 80 FIRE HYDRANT ISOLATOR – SOUTH AUSTRALIA

FEATURES

SA Fireplugs provide direct access to

water pipelines for fire fighting purposes.
Access is gained with the attachment of a
standpipe to the hydrant lugs and opening
of the valve.
Grade 316 stainless steel fasteners for long
life application.
Special SA Water spindle cap.

TECHNICAL DATA

Allowable Operating Pressures

1600kPa or 3500kPa
Maximum Temperature
50˚C
End Connections
DN 80 flanged to AS 4087
Specifications
SA Water No. SAW 2001
Certifications
AS/NZS 4020
Testing of products for use in
contact with drinking water.

FLANGED
AS 4087
DN 80

DN80 – PN16
Code Size (MM) Description
VHAC008S7 80 80 B5 AUSLITE SA FIREPLUG

DN80 – PN35
Size
Code Description
(MM)
VHDF008S7 80 80 B6 HYD ISOLATOR-SA FIREPLUG

Conforms to South Australia water specification SAW2001.

2.53
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW® HYDRANT & AIR VALVE ISOLATORS

VALVES / HYDRANT VALVES

DN80 FIRE HYDRANT ISOLATOR – WESTERN AUSTRALIA

FEATURES

The WA Fire Hydrant is designed and

manufactured to SPS 292.
Jumper valve for back flow prevention.
Slotted mounting holes to match existing
Dn90 flanged risers.
WA Fire Hydrant Isolators provide direct
access to water pipelines for fire protection
services, water and neutral liquid
applications. Access is gained with the
attachment of a standpipe to the hydrant lugs.
Insulation essential for installations subject
to temperatures of 0˚C and lower.

TECHNICAL DATA

Allowable Operating Pressures-1600kpa

Hydraulic test to SPS 292:
Seat: 16 bar
Body: 24 bar
Maximum Temperature
Valve designed for use up to 70˚C Where
applicable; for AS 4020 compliance, max
temp 40˚C
Note: Always observe pipe material
recommended operating temperatures

End Connections
Universally drilled AS 2129 Table D, DN90/
DN100, slotted holes
Certifications
AS/NZS 4020 Testing of products for use in
contact with drinking water

FLANGED DN 80
AS 4087

DN100 – PN16
Code Size (MM) Description
VHDC010S7 100 100 B5 WA HYD ISOLATOR WA FC

Conforms to Western Australia water corporation specification SPS292.

2.54
VALVES

KNIFE GATE
VALVES
 VIADUX WATER NETWORK SOLUTIONS

XDV-UDH KNIFE GATE VALVES

VALVES / KNIFE GATE VALVES

FLANGE DN50 – DN600 LUGGED

FEATURES

Special L shaped replaceable seat.

XDV-UDH With XDV-UDH With Roller bearings in SS housing on
Handwheel Pneumatic Actuator all sizes.
Fully lugged to suit AS4087 CL16.
Stainless steel stem protection
tube included.
Gearbox included on DN450 and above.
Stainless steel safety guards included on
all sizes.
Special adjustable gate guide ensures
no leakage.
Viton seat as standard.
Temperature range up to 200°C
(depending on seat).

OPTIONS

ISO mount type.

WCB or Duplex body.
Wafer type body.
EPDM, NBR, PTFE or metal seat.
Electric or pneumatic actuator.
Non-rising stem.
Limit switches.
Chain wheel.
Code Size (MM) Description Anti-clockwise close.
VKGLAVF050HW 50 50 KNIFE GATE VLV ST/ST LUGGED HW Extensions.
VKGLAVF065HW 65 65 KNIFE GATE VLV ST/ST LUGGED HW
VKGLAVF080HW 80 80 KNIFE GATE VLV ST/ST LUGGED HW TECHNICAL DATA
VKGLAVF100HW 100 100 KNIFE GATE VLV ST/ST LUGGED HW
VKGLAVF125HW 125 125 KNIFE GATE VLV ST/ST LUGGED HW Size Range
VKGLAVF150HW 150 150 KNIFE GATE VLV ST/ST LUGGED HW DN50-DN1200

VKGLAVF200HW 200 200 KNIFE GATE VLV ST/ST LUGGED HW Pressure Class
Max PN10 dependant on valve size
VKGLAVF225HW 225 225 KNIFE GATE VLV ST/ST LUGGED HW
Face to Face
VKGLAVF250HW 250 250 KNIFE GATE VLV ST/ST LUGGED HW
MSS SP-81
VKGLAVF300HW 300 300 KNIFE GATE VLV ST/ST LUGGED HW
Maximum Temperature Rating:
VKGLAVF350HW 350 350 KNIFE GATE VLV ST/ST LUGGED HW (at nil pressure)
VKGLAVF375HW 375 375 KNIFE GATE VLV ST/ST LUGGED HW 200˚C Viton (standard)
120˚C EPDM (optional)
VKGLAVF400HW 400 400 KNIFE GATE VLV ST/ST LUGGED HW
90˚C NBR (optional)
VKGLAVF450HW 450 450 KNIFE GATE VLV ST/ST LUGGED HW 200˚C PTFE (optional)
200˚C Metal (optional)
VKGLAVF500HW 500 500 KNIFE GATE VLV ST/ST LUGGED HW
Lugged to suit
VKGLAVF600HW 600 600 KNIFE GATE VLV ST/ST LUGGED HW
AS4087, Class 16. (others on request)

2.56
VALVES

AIR VALVES
 VIADUX WATER NETWORK SOLUTIONS

BERMAD® A30 AUTOMATIC AIR VALVE

VALVES / AIR VALVES

SINGLE ORIFICE, AIR ACCUMULATION PREVENTION, LOW PRESSURE SEALING

BERMAD A30 is a high quality automatic air

release valve that allows efficient release of air
pockets from pressurized pipes.
With its advanced design, this valve provides
excellent protection against air accumulation
with improved sealing in low pressure
conditions.

FEATURES

Large diameter automatic orifice.

Compact, simple and reliable structure.
Fully corrosion-resistant parts.

APPLICATIONS

Pipelines – Protection against air accumulation

in horizontal or low slope lines and road / river
crossings.
In proximity to control valves and water meters
– Prevention of biased readings and inaccurate
pressure regulation due to air flow through
these devices.
Industrial and residential networks – Protection
against air accumulation.

BERMAD® A30 AUTOMATIC AIR VALVE BENEFITS

INLET 1” MALE BSP
Code Size (MM) Description High air flow rates.
VAIR1A10 25 1" M BSP Small Orifice AV PN10 GRP Grey Low pressure sealing (0.1bar).
VAWW1A30 25 1" M BSP Small Orifice AV PN16 GRP BLACK Lower maintenance and increased life span.

Single orifice, air accumulation prevention, low pressure sealing

2.58
 VALVES

BERMAD® C30 AUTOMATIC AIR VALVE

VALVES / AIR VALVES

DOUBLE ORIFICE, AIR ACCUMULATION AND VACUUM PREVENTION, LOW PRESSURE SEALING

BERMAD C30 is a high quality combination

air valve for a variety of water networks and
operating conditions. It evacuates air during
pipeline filling, allows efficient release of air
pockets from pressurized pipes, and enables
large air volume intake in the event of network
draining.
With its advanced aerodynamic design,
this double orifice valve provides excellent
protection against air accumulation and
prevents vacuum formation with improved
sealing in low pressure conditions.

BENEFITS

Higher than usual air flow rates.

Low pressure sealing (0.1bar).
Lower maintenance and increased life span
Pressure gauge connection, check point or test
drain for air valve function.

FEATURES

Straight flow body with large diameter

automatic orifice.
Aerodynamic full-body kinetic shield.
Compact, simple and reliable structure.
Fully corrosion-resistant parts.
Surge Protection (optional).
Inflow Prevention (optional).
BERMAD® C30 AUTOMATIC AIR VALVE Service Ports fitted (optional).
INLET 1”-2” MALE BSP OR DN80 FLANGED Threaded Side outlet (Optional for DN50/2”).
Code Size (MM) Description
VAIR2C10 50 2" M BSP Comb AV PN12 GRP Grey/RED APPLICATIONS
VAIR3C10 80 3" flanged Comb AV PN12 GRP Grey/RED
VAWW1C30 25 1" M BSP Comb AV PN16 GRP Pipelines – Protection against air accumulation
VAWW2C30 50 2"M BSP Comb AV PN16 GRP and vacuum formation at elevations, slope
change points and road/ river crossings.
VAWW3C30 80 3" flanged Comb AV PN16 GRP
Water networks – Protection against air
accumulation and vacuum formation. In
Double orifice, air accumulation and vacuum proximity to control valves and water meters –
prevention, low pressure sealing Prevention of biased readings and inaccurate
pressure regulation due to air flow through
these devices.
Industrial and residential networks - Protection
against air accumulation.

2.59
 VIADUX WATER NETWORK SOLUTIONS

BERMAD® C50 COMBINATION AIR VALVE

VALVES / AIR VALVES

SEWAGE & WASTEWATER COMBINATION AIR VALVE – DOUBLE ORIFICE WITH SURGE PROTECTION, AIR ACCUMULATION
& VACUUM PREVENTION, LOW PRESSURE SEALING AND EASY MAINTENANCE

BERMAD C50 is a high quality combination air valve

for a variety of sewage and wastewater networks and
operating conditions. It evacuates air during pipeline
filling, allows efficient release of air and gas pockets
from pressurized pipes, and enables large volume
air intake in the event of network draining.
With its advanced aerodynamic design and double
orifice, this valve provides excellent protection
against air and gas accumulation and vacuum
formation with improved sealing under low pressure
conditions.

BENEFITS

Higher than usual air flow rates.

Low pressure sealing (0.05 bar).
Vortex back washing.
Lower and easier maintenance.
Increased life span.

FEATURES

Straight flow body with large diameter

automatic orifice.
Aerodynamic full-body kinetic shield.
Elongated body design with
non-stick coating.
Valve is opened from the top.
2 service ports.
Compact, simple, robust and
reliable structure.
Fully corrosion-resistant parts.
BERMAD® C50 COMBINATION AIR VALVE
Surge Protection (optional).
INLET 2” FEMALE BSP OR DN50-DN80 FLANGED
Inflow Prevention (optional).
Code Size (MM) Description
Drainage valve (optional).
VAWW2BPC50SP 50 2" F BSP COMB SAV SP PN10 GRP
VAWW2BDC50SP 50 2"FL COMB SAV SP TD PN10 GRP
APPLICATIONS
VAWW3BDC50SP 80 80mm FL COMB SAV SP TD PN10 GRP

Sewage and wastewater pumping stations

Sewage & wastewater combination air valve – double orifice with – Air relief and vacuum prevention.
surge protection, air accumulation & vacuum prevention, low
pressure sealing and easy maintenance Sewage and wastewater pipelines
–P
 rotection against air and gas accumulation and
vacuum formation at elevations, slope change
points and at road /river crossings.
Municipal and industrial wastewater treatment
plants – Protection against air and gas accumulation
and vacuum formation.

2.60
 VALVES

BERMAD® C60 / C65 COMBINATION AIR VALVE

VALVES / AIR VALVES

SEWAGE & WASTEWATER COMBINATION AIR VALVE – DOUBLE ORIFICE WITH SURGE PROTECTION, AIR ACCUMULATION
& VACUUM PREVENTION, LOW PRESSURE SEALING AND EASIER MAINTENANCE

BERMAD C65 is a high quality combination air valve for a variety

of sewage and wastewater networks and operating conditions.
It evacuates air during pipeline filling, allows efficient release of
air and gas pockets from pressurized pipes, and enables large
volume air intake in the event of network draining.
With its advanced aerodynamic design, double orifice and
anti-slam / slow closing device, this valve provides excellent
protection against air and gas accumulation, surge and water
hammers with improved sealing under low pressure conditions.

BENEFITS

Higher than usual air flow rates.

Low pressure sealing (0.1bar).
Vortex back washing.
Lower and easier maintenance.
Increased life span.

FEATURES

Straight flow body.

Aerodynamic full-body kinetic shield.
Elongated body design with non-stick coating.
Valve is opened from the top.
2 service ports.
BERMAD® C60 / C65 COMBINATION AIR VALVE
Compact, simple, robust and
INLET 2” FEMALE BSP OR DN50-DN100 FLANGED
reliable structure.
Code Size (MM) Description
Fully corrosion-resistant parts.
VAWW2BPC60SP 50 2" F BSP COMB SAV SP PN16 DI
Surge Protection (optional).
VAWW2BDC60SP 50 2"FL COMB SAV SP TD PN16 DI
Inflow Prevention (optional).
VAWW3BDC60SP 80 80mm FL COMB SAV SP TD PN16 DI
VAWW4BDC60SP 100 100mm FL COMB SAV SP TD PN16 DI Drainage valve (optional).

APPLICATIONS
Sewage & wastewater combination air valve – double orifice with
surge protection, air accumulation & vacuum prevention, low
pressure sealing and easier maintenance Sewage and wastewater pumping stations
– Air relief, vacuum prevention and surge protection.
Sewage and wastewater pipelines
–P
 rotection against air and gas accumulation and vacuum
formation at elevations, slope change points and at road/river
crossings.
Protection against vacuum formation, surge and water hammer
at points likely to experience water column separation.
Municipal and industrial wastewater treatment plants –
Protection against air and gas accumulation and vacuum
formation.

2.61
 VIADUX WATER NETWORK SOLUTIONS

BERMAD® C70 COMBINATION AIR VALVE

VALVES / AIR VALVES

DOUBLE ORIFICE WITH SURGE PROTECTION, 2-STEP FUNCTION AUTOMATIC ORIFICE, AIR ACCUMULATION & VACUUM
PREVENTION AND LOW PRESSURE SEALING

BERMAD C70 is a high quality combination air valve for

a variety of water networks and operating conditions. It
evacuates air during pipeline filling, allows efficient release
of air pockets from pressurized pipes, and enables large
volume air intake in the event of network draining.
With its advanced aerodynamic design, double orifice and
anti-slam / slow closing device, this valve provides excellent
protection against air accumulation, vacuum formation and
pressure surges, with improved sealing in low pressure
conditions. The valve minimizes water spraying during
air release.

APPLICATIONS

Pumping stations and deep well pumps

– Air relief, surge protection and vacuum prevention.
Pipelines
– Protection against air accumulation and vacuum
formation at elevations, slope change points and
at road / river crossings.
Water networks
– Protection against vacuum formation, surge and
water hammers at points likely to experience water
column separation.

BENEFITS

Higher than usual air flow rates.

BERMAD® C70 COMBINATION AIR VALVE Low pressure sealing (0.1bar).

INLET 2” FEMALE BSP OR DN50-DN150 FLANGED Minimizes water spraying during

air release.
Code Size (MM) Description
Lower maintenance and increased life span.
VAWW2BPC70SP 50 2"F BSP COMB AV SP PN16 DI
Australian Standards - AS4956 approved (Licence No
VAWW2HPC70SP 50 2"F BSP COMB AV SP PN35 DI
SMKP25537 SAI Global) and AS/NZS 4020 approved.
VAWW2BDC70SP 50 2"FL COMB AV SP TD PN16 DI
VAWW2BHC70SP 50 2"FL COMB AV SP TD PN35 DI
FEATURES
VAWW3BDC70SP 80 80MM FL COMB AV SP PN16 DI
VAWW3BHC70SP 80 80MM FL COMB AV SP PN35 DI Straight flow body with nominal (equal) inlet
VAWW4BDC70SP 100 100MM FL COMB AV SP PN16 DI and outlet size.
VAWW4BHC70SP 100 100MM FL COMB AV SP PN35 DI Aerodynamic full-body kinetic shield.
VAWW6BDC70SP 100 150MM FL COMB AV SP PN16 DI Innovative 2-step function, automatic orifice.
VAWW6BHC70SP 150 150MM FL COMB AV SP PN35 DI Optional outlets.
VAWW8BDC70SP 150 150MM FL COMB AV SP PN16 DI 2 service ports.
VAWW8BHC70SP 150 150MM FL COMB AV SP PN35 DI Drainage valve.
Compact, simple, robust and reliable structure.
Double orifice with surge protection, 2-step function
automatic orifice, air accumulation & vacuum prevention Fully corrosion-resistant parts.
and low pressure sealing Surge Protection (optional).
Inflow Prevention (optional).
Insect Screen (optional).
2.62
VALVES

VALVE
ANCILLARY
 VIADUX WATER NETWORK SOLUTIONS

SUREFLOW®

VALVES / VALVE ANCILLARY

VALVE ANCHOR KIT

VALVE THRUST RESTRAINT SYSTEM – DN 100 & DN 150 SOCKET GATE VALVES

DN100 & DN150 SOCKET GATE VALVES

Code Size (MM) Description
VZ10ANCHORKIT 100-150 100-150 VALVE ANCHOR KIT

Diagram 1
25mm
Nom.
Clearance

2.64
 VALVES

VALVE SPINDLE EXTENSION

VALVES / VALVE ANCILLARY

FACILITATE THE REMOTE OPERATING OF GATE VALVES WITH DUCTILE IRON PIPE SYSTEMS

SET LENGTH 150 – 600MM

Code Length (MM) Description
VZDXA0150S 150 VLV SPDLE EXT 150EL AS & SCREW
VZDXA0300S 300 VLV SPDLE EXT 300EL AS & SCREW
VZDXA0375S 375 VLV SPDLE EXT 375EL AS & SCREW
VZDXA0450S 450 VLV SPDLE EXT 450EL AS & SCREW
VZDXA0525S 525 VLV SPDLE EXT 525EL AS & SCREW
VZDXA0600S 600 VLV SPDLE EXT 600EL AS & SCREW

VARIABLE LENGTH EXTENSION SPINDLE

Code Description
VZDEA0500VAR 301-500 EL VALVE SPINDLE EXTENSION FAB
VZDEA0700VAR 501-700 EL VALVE SPINDLE EXTENSION FAB
VZDEA0900VAR 701-900 EL VALVE SPINDLE EXTENSION FAB
VZDEA1100VAR 901-1100 EL VALVE SPINDLE EXTENSION FAB
VZDEA1300VAR 1101-1300 EL VALVE SPINDLE EXTENSION FAB
VZDEA1500VAR 1301-1500 EL VALVE SPINDLE EXTENSION FAB
VZDEA1700VAR 1501-1700 EL VALVE SPINDLE EXTENSION FAB
VZDEA1900VAR 1701-1900 EL VALVE SPINDLE EXTENSION FAB
VZDEA2100VAR 1901-2100 EL VALVE SPINDLE EXTENSION FAB
VZDEA2300VAR 2201-2300 EL VALVE SPINDLE EXTENSION FAB

GENERAL APPLICATION VZDEA2500VAR 2301-2500 EL VALVE SPINDLE EXTENSION FAB

VZDEA2700VAR 2501-2700 EL VALVE SPINDLE EXTENSION FAB
VZDEA2900VAR 2701-2900 EL VALVE SPINDLE EXTENSION FAB
SUREFLOW Valve Spindle Extensions facilitate the opening and
®

VZDEA3100VAR 2901-3100 EL VALVE SPINDLE EXTENSION FAB

closing of gate valves where the valves are located below ground,
or in pits, at an extended distance from the operating level VZDEA3300VAR 3101-3300 EL VALVE SPINDLE EXTENSION FAB
VZDEA3500VAR 3301-3500 EL VALVE SPINDLE EXTENSION FAB
VZDEA3700VAR 3501-3700 EL VALVE SPINDLE EXTENSION FAB
TECHNICAL DATA VZDEA3900VAR 3701-3900 EL VALVE SPINDLE EXTENSION FAB
VZDEA4100VAR 3901-4100 EL VALVE SPINDLE EXTENSION FAB
Length  VZDEA4300VAR 4101-4300 EL VALVE SPINDLE EXTENSION FAB
Minimum 250mm VZDEA4500VAR 4301-4500 EL VALVE SPINDLE EXTENSION FAB
Maximum 7500mm
VZDEA4700VAR 4501-4700 EL VALVE SPINDLE EXTENSION FAB
Note: longer lengths available upon request VZDEA4900VAR 4701-4900 EL VALVE SPINDLE EXTENSION FAB
Standards VZDEA5100VAR 4901-5100 EL VALVE SPINDLE EXTENSION FAB
AS 2638 Gate valves for waterworks purposes. VZDEA5300VAR 5101-5300 EL VALVE SPINDLE EXTENSION FAB
VZDEA5500VAR 5301-5500 EL VALVE SPINDLE EXTENSION FAB
VZDEA5700VAR 5501-5700 EL VALVE SPINDLE EXTENSION FAB
VZDEA5900VAR 5701-5900 EL VALVE SPINDLE EXTENSION FAB
VZDEA6100VAR 5901-6100 EL VALVE SPINDLE EXTENSION FAB
VZDEA6300VAR 6101-6300 EL VALVE SPINDLE EXTENSION FAB
VZDEA6500VAR 6301-6500 EL VALVE SPINDLE EXTENSION FAB
VZDEA6700VAR 6501-6700 EL VALVE SPINDLE EXTENSION FAB
VZDEA6900VAR 6701-6900 EL VALVE SPINDLE EXTENSION FAB
VZDEA7100VAR 6901-7100 EL VALVE SPINDLE EXTENSION FAB
VZDEA7300VAR 7101-7300 EL VALVE SPINDLE EXTENSION FAB
VZDEA7500VAR 7301-7500 EL VALVE SPINDLE EXTENSION FAB

2.65
VIADUX WATER NETWORK SOLUTIONS

VALVES / VALVE ANCILLARY

2.66