Scribd
Upload
9 views4 pages

Component Location: B2504 Warning Lamp Short or Short To Battery General Information

The document details the B2504 warning lamp issue related to the airbag control system in the PICANTO (SA) model from 2010 onwards. It describes the conditions under which the diagnostic trouble code (DTC) B2504 is set, potential causes, and inspection procedures for diagnosing and repairing the issue. Additionally, it emphasizes the importance of verifying repairs through a scan tool after addressing the fault.

Uploaded by

reza mohamadtabar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views4 pages

Component Location: B2504 Warning Lamp Short or Short To Battery General Information

The document details the B2504 warning lamp issue related to the airbag control system in the PICANTO (SA) model from 2010 onwards. It describes the conditions under which the diagnostic trouble code (DTC) B2504 is set, potential causes, and inspection procedures for diagnosing and repairing the issue. Additionally, it emphasizes the importance of verifying repairs through a scan tool after addressing the fault.

Uploaded by

reza mohamadtabar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

PICANTO(SA) > 2010 > G 1.

0 SOHC > Airbag > Airbag Control > B2504 Warning lamp
short or short to battery

B2504 Warning lamp short or short to battery > General Information


Component Location

General Description
Air bag warning lamp is located at cluster
When key is in ‘ignition on’ position, SRSCM performs diagnosis of overall air bag system.If there’s no fault, air bag.
Warning lamp in cluster flickers for a whlie and then goes out.
RSCM measures voltage of out terminal of warning lamp to check if warnning lamp is operated in accordance with signal SRSCM
sends.

DTC Description
The SRSCM sets DTC B2504 when warning lamp short or short to battery.

DTC Detecting Condition


Item Detecting Condition Possible Cause
DTC Strategy ● Check voltage
Enable ● Ignition "ON"
Case 1 conditions ● When AWL is commanded ON by the ACU and Shorted to Battery
(AWL Lamp
Off) Threshold
●
value
● Short circuit in
● Ignition "ON" warning lamp
Enable
Case 2 ● When AWL is commanded OFF by the ACU and Open or shorted to harness.
conditions
(AWL Lamp ground ● Faulty
On) SRSCM.
Threshold
● Battery voltage > 1.5 V
value
Qualification ● More than 2~2.025 sec
Diagnostic
Time De-
● More than 10~10.025 sec
Qualification

Schematic Diagram
B2504 Warning lamp short or short to battery > Scantool Diagnostics > Monitor Scantool Data
Monitor Scantool Data
1. Ignition "OFF", connect scantool.
2. Ignition "ON"& Engine "OFF", select "Diagnostic Trouble Codes(DTC)" mode.
3. Monitor diagnostic trouble code and present of trouble code.
4. Using a scan tool, clear the DTC.

- H : Historical fault
- P : Present fault

5. Is DTC present problem ?


▶ Go to "W/Harness Inspection" procedure.

▶ Displaying nothing(no DTC) or DTC with label "H"(historical) shows that Fault is intermittent caused by poor contact in the
part’s and/or SRSCM connector or was repaired and SRSCM memory was not cleared.
Thoroughly check shorting bar/shorting bar release pin and connectors for looseness, poor connection, bending, corrosion,
contamination, deterioration, or damage.
▶ Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.

B2504 Warning lamp short or short to battery > Inspection/Repair > W/Harness Inspection
Terminal and Connector Inspection
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2. Thoroughly check shorting bar/shorting bar release pin and connectors for looseness, poor connection, bending, corrosion,
contamination, deterioration, or damage.
3. Has a problem been found?

▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.

▶ Go to "Warning lamp Circuit Inspection" procedure..

Main harness Circuit Inspection


1. Ignition "OFF"
2. Remove the Instrument cluster from crash pad assembly.
3. Ignition "ON" & Engine "OFF".
4. Measure voltage between terminal "M07-1-1" of the Instrument cluster harness connector and chassis ground.
1) Specification : Battery Voltage
5. Measure voltage between terminal "33" of the SRSCM harness connector and chassis ground..
1) Specification : 0 Voltage

6. Is the measured voltage within specifications?

▶ Check warning lamp and connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or
damage. Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.

▶ Check airbag fuse, passenger compartment junction block, harness between junction block and SRS . Repair as necessary
and go to "Verification of Vehicle Repair" procedure.
B2504 Warning lamp short or short to battery > Verification of Vehicle Repair
Verification of Vehicle Repair
After a repair, it is essential to verify that the fault has been corrected
1. Connect scan tool and select "Diagnostic Trouble Codes(DTC)" mode
2. Using a scan tool, clear the DTC.
3. Operate the vehicle within DTC Enable conditions in General information.
4. Are any DTC present ?

▶ Go to the applicable troubleshooting procedure.

▶ System is performing to specification at this time.

You might also like