Scribd
Upload
44 views4 pages

Component Location: B2505 Passenger Airbag Off Warning Lamp Failure General Information

The document details the B2505 Passenger airbag off warning lamp failure, including its general description, diagnostic trouble code (DTC) conditions, and inspection/repair procedures. It outlines potential causes for the failure, such as burnt-out components or circuit issues, and provides steps for using a scan tool to diagnose and verify repairs. The document emphasizes the importance of thorough inspections and proper verification after repairs to ensure the system functions correctly.

Uploaded by

reza mohamadtabar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
44 views4 pages

Component Location: B2505 Passenger Airbag Off Warning Lamp Failure General Information

The document details the B2505 Passenger airbag off warning lamp failure, including its general description, diagnostic trouble code (DTC) conditions, and inspection/repair procedures. It outlines potential causes for the failure, such as burnt-out components or circuit issues, and provides steps for using a scan tool to diagnose and verify repairs. The document emphasizes the importance of thorough inspections and proper verification after repairs to ensure the system functions correctly.

Uploaded by

reza mohamadtabar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

PICANTO(SA) > 2010 > G 1.

0 SOHC > Airbag > Airbag Control > B2505 Passenger airbag
off warning lamp failure

B2505 Passenger airbag off warning lamp failure > General Information
Component Location

General Description
PAD Switch(Passenger airbag deactivation Switch) is the device which prevents Passenger airbag from being deployed when the
passenger seat is unoccupied as driver turning OFF PAD Switch.
When PAD Switch turned OFF, " PASSENGER SRS OFF" lamp on cluster turns ON.

DTC Description
The above DTCs are recorded when the defect of the Passenger airbag off warning lamp is detected in Passenger airbag off
warning lamp circuit.

DTC Detecting Condition


Item Detecting Condition Possible cause
● Burnt-out
DTC Strategy ● Check voltage fuse..
● Burnt-out
airbag off
Enable conditions ● Ignition "ON" warning lamp.
● Open circuit in
airbag off
warning lamp
Qualification ● More than 1.2 sec
harness.
● Short circuit in
Diagnostic airbag off
Time warning lamp
De-
● More than 2~17 sec harness.
Qualification
● Faulty
SRSCM.

Schematic Diagram
B2505 Passenger airbag off warning lamp failure > Scantool Diagnostics > Monitor Scantool Data
Monitor Scantool Data
1. Ignition "OFF", connect scantool.
2. Ignition "ON"& Engine "OFF", select "Diagnostic Trouble Codes(DTC)" mode.
3. Monitor diagnostic trouble code and present of trouble code.
4. Using a scan tool, clear the DTC.

- H : Historical fault
- P : Present fault

5. Is DTC present problem ?

▶ Go to "W/Harness Inspection" procedure.


▶ Displaying nothing(no DTC) or DTC with label "H"(historical) shows that Fault is intermittent caused by poor contact in the
part’s and/or SRSCM connector or was repaired and SRSCM memory was not cleared.
Thoroughly check shorting bar/shorting bar release pin and connectors for looseness, poor connection, bending, corrosion,
contamination, deterioration, or damage.
▶ Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure..

B2505 Passenger airbag off warning lamp failure > Inspection/Repair > W/Harness Inspection
Terminal and Connector Inspection
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2. Thoroughly check shorting bar/shorting bar release pin and connectors for looseness, poor connection, bending, corrosion,
contamination, deterioration, or damage.
3. Has a problem been found?

▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.

▶ Go to "Warning lamp Circuit Inspection" procedure

Warning lamp Circuit Inspection


1. Ignition "OFF".
2. Disconnect SRSCM main harness connector.
3. Ignition "ON" & Engine "OFF".
4. Measure voltage between terminal "72" of the SRSCM main harness connector and chassis ground.
1) Specification : Batt Voltage

5. Is the measured voltage within specifications?

▶ Substitute a known-good SRSCM, and check for proper operation.


If the problem is corrected, replace SRSCM and then go to "Verification of Vehicle Repair" procedure.

▶ Check airbag fuse, airbag off warning lamp, junction box, harness between junction block and SRS . Repair as necessary and
go to "Verification of Vehicle Repair" procedure.

B2505 Passenger airbag off warning lamp failure > Verification of Vehicle Repair
Verification of Vehicle Repair
After a repair, it is essential to verify that the fault has been corrected
1. Connect scan tool and select "Diagnostic Trouble Codes(DTC)" mode
2. Using a scan tool, clear the DTC.
3. Operate the vehicle within DTC Enable conditions in General information.
4. Are any DTC present ?

▶ Go to the applicable troubleshooting procedure.

▶ System is performing to specification at this time.

You might also like