LIFTING CAPACITY

HORSEPOWER Gross: 42.8 kW 57 HP @ 1950 rpm Net: 41 kW 55 HP @ 1950 rpm

A: Reach from swing center B: Bucket hook height C: Lifting capacity Cf: Rating over front Cs: Rating over side : Rating at maximum reach

OPERATING WEIGHT 6945 7535 kg 15,315 16,615 lb BUCKET CAPACITY 0.09 0.34 m3 0.12 0.45 yd3

B C
PC78US-8 A B 5.0m 16' 3.0m 9' 0.0m 0' -2.0m -6' PC78US-8 A B 5.0m 16' 3.0m 9' 0.0m 0' -2.0m -6'

Arm : 1650mm 5'5" Bucket : 0.28 m3 0.37 yd3 SAE heaped Shoe width : 450mm 17.7" triple grouser Without blade Maximum 4.5m 14' 3.0m 9' Cf Cs Cf Cs Cf Cs *1790 *1790 *1780 1430 *3960 *3960 *3920 3150 1500 1130 *2300 2280 1160 860 3320 2500 *5070 5030 2550 1910 1370 1000 2650 1900 1050 760 3020 2220 5850 4200 2310 1690 1360 1000 *2630 1890 1440 1050 3010 2210 *5810 4180 3170 2330 Arm : 2250mm 7'5" Bucket : 0.20 m3 0.26 yd3 SAE heaped Shoe width : 450mm 17.7" triple grouser Without blade 4.5m 14' 3.0m 9' Maximum Cf Cs Cf Cs Cf Cs *1490 1200 *1420 1090 *3290 2650 *3140 2420 1540 1170 *1870 *1870 980 720 3400 2580 *4130 *4130 2160 1600 1370 1000 2660 1920 880 640 3020 2220 5880 4230 1950 1410 1330 960 2590 1850 1120 820 2930 2130 5710 4070 2490 1810

Unit : kg lb 1.5m 4' Cf Cs

PC78US-8
PC

*4060 *8960

*4060 *8960 Unit : kg lb 1.5m 4'

78US

COMPACT HYDRAULIC EXCAVATOR

Cf

Cs

*4230 *9330

*4230 *9330

* Load is limited by hydraulic capacity rather than tipping. Ratings are based on SAE Standard No. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.

PC78US-8 A B 5.0m 16' 3.0m 9' 0.0m 0' -2.0m -6' PC78US-8 A B 5.0m 16' 3.0m 9' 0.0m 0' -2.0m -6'

Arm : 1650mm 5'5" Bucket : 0.28 m3 0.37 yd3 SAE heaped Shoe width : 450mm 17.7" triple grouser Blade on ground Maximum 4.5m 14' 3.0m 9' Cf Cs Cf Cs Cf Cs *1790 *1790 *1780 1500 *3960 *3960 *3920 3310 *1780 1190 *2300 *2300 *1670 910 *3930 2640 *5070 *5070 *3680 2020 *2120 1060 *3360 2010 *1710 810 2350 *4680 *7410 4430 *3770 1800 *1510 1060 *2710 2000 *1650 1120 *3330 2340 *5980 4410 *3650 2460 Arm : 2250mm 7'5" Bucket : 0.20 m3 0.26 yd3 SAE heaped Shoe width : 450mm 17.7" triple grouser Blade on ground 4.5m 14' 3.0m 9' Maximum Cf Cs Cf Cs Cf Cs *1490 1260 *1420 1150 *3290 2780 *3140 2540 *1570 1230 *1870 *1870 *1350 770 *3470 2710 *4130 *4130 *2990 1700 *2090 1060 *3320 2020 *1520 680 *4600 2350 *7330 4460 *3360 1510 *1880 1020 *3010 1950 *1540 870 *4140 2260 *6640 4300 *3400 1920

Unit : kg lb 1.5m 4' Cf Cs

*4060 *8960

*4060 *8960 Unit : kg lb 1.5m 4'

Cf

Cs

*4230 *9330

*4230 *9330

* Load is limited by hydraulic capacity rather than tipping. Ratings are based on SAE Standard No. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.

www.Komatsu.com

Printed in Japan 200810 IP.As(10)

Photo may include optional equipment.

CEN00339-00

Materials and specifications are subject to change without notice. is a trademark of Komatsu Ltd. Japan.

PC78US-8 C O M P A C T H Y D R A U L I C E X C A V A T O R

COMPACT HYDRAULIC EXCAVATOR

PC78US-8
HORSEPOWER Gross: 42.8 kW 57 HP @ 1950 rpm Net: 41 kW 55 HP @ 1950 rpm OPERATING WEIGHT 6945 7535 kg 15,315 16,615 lb

WALK-AROUND
Ecology and Economy Features Low emission engine
A powerful, turbocharged and air-to-air aftercooled Komatsu SAA4D95LE-5 provides 41 kW 55 HP. This engine is EPA Interim Tier 4 and EU Stage 3A emissions certified without sacrificing power or machine productivity.

Large Comfortable Cab

Low noise design cab Sliding convex door facilitates easy entrance in confined areas. Large cab improves working space. See page 6.

Large TFT LCD Monitor

Easy-to-see and use 7" large multifunction color monitor Can be displayed in 12 languages for global support.
TFT : Thin Film Transistor LCD : Liquid Crystal Display

BUCKET CAPACITY 0.09 0.34 m3 0.12 0.45 yd3

Low operation noise

See page 4.

Productivity Features Tight tail swing

Excellent operation in tight tail swing radius design Tail swing radius: 1240 mm 4'1

Mode selection
Five working modes designed to match engine speed, pump delivery and system pressure. Economy mode improves fuel consumption. Eco-gauge for energy-saving operations Extended idling caution for fuel conservation See page 5.

See page 9.

High mobility
Large drawbar pull and steering force are evident when operating on a slope or other rough terrain. Max. drawbar pull: 66.9 kN 6820 kgf 15,050 lb The machine travel speed changes automatically to Hi or Lo at optimal points according to the travel load.

Easy Maintenance
Side-by-side cooling function enables only the cooling unit to be attached and detached. Easy access to engine oil filter, engine main fuel filter and fuel drain valve Equipped with the fuel pre-filter (with water separator) Equipped with the Equipment Management Monitoring System (EMMS) monitoring system. See page 8.

Safety Features
Cab dedicated to hydraulic excavator for protecting the operator in the event of a roll over accident. Safety enhancement with large sideview and rear-view mirrors. See page 7.
2 3
Photo may include optional equipment.

PC78US-8 C O M P A C T H Y D R A U L I C E X C A V A T O R

COMPACT HYDRAULIC EXCAVATOR

PC78US-8

PRODUCTIVITY & ECOLOGY FEATURES

Komatsu Technology
Seven-inch TFT liquid crystal display

Advantage even in Confined Job Site

Tight Tail Swing
Hydraulic system controller

Two Automatic Travel Speeds

High or lowwhichever speed suits the ground and job conditionscan be selected with one touch. As terrain changes, travel speed will automatically shift up or down within the selected speed range.

The narrow swing area is well suited for operation in confined areas with only a 80mm (3.1") protrusion over the tracks.

Road & bridge work

Short swing radius Working Modes Selectable

2990mm 9'10"
The PC78US-8 excavator is equipped with five working modes (P, E, L, B and ATT mode). Each mode is designed to match engine speed and pump speed with the current application. This provides the flexibility to match equipment performance to the job at hand.

2990mm

Komatsu develops and produces all major components in house such as engines, electronics and hydraulic components. Combining Komatsu Technology, and customer feedback, Komatsu is achieving great advancements in technology. To achieve both high levels of productivity and economical performance, Komatsu has developed the main components with a total control system. The result is a new generation of high performance and environment-friendly excavators.
Electronic control unit for engine Engine Heavy duty HPCR (High Pressure Common Rail) system Hydraulic control valve

9'10"

1750mm 5'9"

1240mm 4'1"

Working Mode P E L B ATT

Application Power mode Economy mode Lifting mode Breaker mode Attachment mode

Main pump

Advantage Maximum production/power Fast cycle times Good cycle times Better fuel economy

Engine rpm reduction Optimum engine rpm, hydraulic flow Optimum engine rpm, hydraulic flow, 2way

Low Emission Engine

Komatsu SAA4D95LE-5 is EPA Interim Tier 4 and EU Stage 3A emissions certified.

235mm 9.3''
Protrusion from the track (hand rail)

E L B ATT

Work priority P mode Fuel priority E mode

L mode B mode ATT mode
ATT

80mm 3.1''
Protrusion from the track (rear)

Eco-gauge that Assists Energy-saving Operations

The Eco-gauge on the right side of the multi-function color monitor provides environment-

High Mobility
The PC78US-8 exceptional travel performance is provided by

friendly energy-saving operation. Allows focus on operation in the green range with reduced CO2 emissions and efficient fuel consumption.
Eco-gauge

Low Operation Noise

Enables low noise operation using the low-noise engine and methods to cut noise at source. Electronically controlled common rail type engine Multi-staged injection Low noise design Optimal arrangement of sound absorbing materials Partition between the cab and engine room

large drawbar pull and single pump with double flow, and it demonstrates superb maneuverability while operating at its optimum travel speed. It exhibits a large drawbar pull for moving on job sites, traveling in rough terrain and climbing steep slopes. Maximum drawbar pull: 66.9 kN 6820 kgf 15050 lb

Idling Caution Auto-decel

Engine speed automatically slows down when all control levers are set in neutral to minimize fuel consumption.
Photo may include optional equipment.

To prevent unnecessary fuel consumption, an idling caution is displayed on the monitor, if the engine idles for 5 minutes or more. 5

PC78US-8 C O M P A C T H Y D R A U L I C E X C A V A T O R

COMPACT HYDRAULIC EXCAVATOR

PC78US-8

WORKING ENVIRONMENT
Large Comfortable Cab Safety Features
New Cab Design for Hydraulic Excavators
The cab is designed specifically for hydraulic excavators and gains reinforced strength from the pipestructured cab framework. The cab framework provides the high durability and impact resistance with very high impact absorbency. The seat belt keeps the operator in the seat of the cab in the event of a roll over.

Wide Visibility
Large cab and extended front glass enable operator to get better visibility.

Lock Lever
When lock lever is placed in lock position all
Photo : Rigid seat

Retractable Seat Belt

Easy-to-use retractable seat belt is employed.

hydraulic controls (travel, swing, boom, arm, bucket and blade) are inoperable.
Lever shown in lock position

Multi-position Controls
The multi-position, PPC (pressure proportional control) levers allow the operator to work in comfort while maintaining precise control. A double-slide mechanism allows the seat and controllers to move together or independently, allowing the operator to position the seat and controllers for maximum productivity and comfort.

Large Cab
Large cab provides ample operation space. The cab has wide doorway for easy access.

Automatic Air Conditioner

Automatic air conditioner is utilized. The bi-level control function keeps the operator's head and feet cool and warm respectively. This improved air flow function keeps the inside of the cab comfortable throughout the year. Defroster function keeps cab glass clear.

Emergency Escape Hammer

The cab is equipped with an emergency escape hammer for

Thermal and Fan Guards

Thermal and fan guards are placed around high-temperature parts of the engine and fan drive.

Side-view and Rear-view Mirrors

Large side mirror and rear mirror allow the PC78US-8 to meet the new ISO visibility requirements.

breaking the rear window glass in case of an emergency.

Skylight
Skylight with window can be opened for overhead visibility.

Low Cab Noise

Cab is highly rigid and has excellent sound absorption ability. Thorough improvement of noise source reduction and use of low noise engine, hydraulic equipment, and air conditioner allows this machine to generate a low level of noise.
Photo : Rigid seat

Sliding Convex Door

The sliding convex door facilitates easy entrance in confined areas.

Travel Alarm Pump/engine Room Partition

Pump/engine room partition prevents oil from spraying onto the engine if a hydraulic hose should burst. An alarm is installed as standard equipment to give other workers a warning when the machine travels in forward or reverse. 7

PC78US-8 C O M P A C T H Y D R A U L I C E X C A V A T O R

COMPACT HYDRAULIC EXCAVATOR

PC78US-8

MAINTENANCE FEATURES
Easy Maintenance
Komatsu designed the PC78US-8 to have easy service access. By doing so, routine maintenance and servicing are less likely to be skipped, which can mean a reduction in costly downtime later on. Here are some of the many service features found on the PC78US-8.
1 2 3

Large TFT LCD Monitor

Large Multi-lingual LCD Monitor
A large user-friendly color monitor enables safe, accurate and smooth work. Improved screen visibility is achieved by the use of TFT liquid crystal display that can easily be read at various angles and lighting conditions. Simple and easy to operate switches. Industry first function keys facilitate multi-function operations. Displays data in 12 languages to globally support operators around the world.
Indicators
1
Auto-decelerator Working mode Travel speed Engine water temperature gauge Hydraulic oil temperature gauge Fuel gauge Eco-gauge Function switches menu

EMMS (Equipment Management Monitoring System) Monitor function

Controller monitors engine oil pressure, coolant temperature and battery charge etc. If controller finds any abnormality, it is displayed on the LCD.

Optimum Maintenance Layout

With the engine hood, right side hood and side service doors, it is possible to access the major maintenance points from ground level. Furthermore, the fuel drain valve, engine oil filter and swing machinery oil filler are remote mounted, facilitating easy maintenance.
Fuel Tank Hydraulic Tank
8 6 4 5 7

2 3 4 5 6 7 8

Maintenance function
Monitor informs replacement time of oil and filters on LCD when the replacement interval is reached.

Basic operation switches

Side-by-side Cooling
Since radiator, aftercooler and oil cooler are arranged in parallel, it is easy to clean, remove and install them. Radiator, aftercooler, and oil cooler made of aluminum have high cooling efficiency and are easily recycled.

1
Tool Box

Equipped with the Fuel Pre-filter (with Water Separator)

Removes water and contaminants in the fuel to prevent fuel problems. (with built-in priming pump)

Function switches
1 2 3

1 Auto-decelerator 2 Working mode selector 3 Traveling selector 4 Buzzer cancel 5 Wiper 6 Windshield washer

Cab
Pump

12 11
Oil Cooler After Cooler Radiator

2 3 4

Basic operation switches

Trouble data memory function

Monitor stores abnormalities for effective troubleshooting.

Engine

10 9 8
6. 7. 8. 9. 10. 11. 12.

Control Valve

Air conditioner operation switches

1. Swing machinery oil filler and dipstick 2. Windshield washer tank 3. Coolant reserve tank 4. Fuel drain valve 5. Fuel pre-filter (with water separator)

PTO oil filler Engine oil filter Engine oil filler Engine oil dipstick Fuel main filter Air cleaner Batteries

Air Conditioner Filter

The air conditioner filter is removed and installed without the use of tools facilitating filter maintenance.

Option
Roadliner
Ideal performance has been achieved with combining the merits of rubber and the strengths of steel in the new Road Liner shoes.
Photo : Bolt-on cutting edge type

Easy Access to Engine Oil Filter, Engine Main Fuel Filter and Fuel Drain Valve
Engine oil filter, engine main fuel filter and fuel drain valve are remote mounted to improve accessibility.

Blade
Back fill blade can quickly and conveniently fill trenches and clear up jobsites.

Additional Counter Weight

Additional weight is designed for increased lift capacity and easy installation.

External air conditioner filter

Internal air conditioner filter

Long Greasing Interval

All bushing lubrication intervals of work equipment except arm top bushings are 500 hours, reducing maintenance cost.

PC78US-8 C O M P A C T H Y D R A U L I C E X C A V A T O R

COMPACT HYDRAULIC EXCAVATOR

PC78US-8

SPECIFICATIONS
ENGINE Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Komatsu SAA4D95LE-5 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water-cooled, 4-cycle Aspiration . . . . . . . . . . . . . . Turbocharged, and air-to-air aftercooled Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Bore x stroke . . . . . . . . . . . . . . . . . . 95 mm x 115 mm 3.74" x 4.53" Piston displacement. . . . . . . . . . . . . . . . . . . . . . . . . . 3.26 ltr 199 in3 Governor . . . . . . . . . . . . . . . . . . . . . . . . All-speed control, electronic Horsepower SAE J1995 . . . . . . . . . . . . . . . . . . . . . . . . . Gross 42.8 kW 57 HP ISO 9249 / SAE J1349 . . . . . . . . . . . . . . . . . . . Net 41 kW 55 HP Rated rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1950 rpm Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct injection Lubrication system Method . . . . . . . . . . . . . . . . . . . . . . . Gear pump, force-lubrication Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Full-flow Air cleaner . . . . . . . . . . . . . . . . . . . . . Dry-type with double elements . . . . . . . . . . . . . . . . . and auto dust evacuator, plus dust indicator EPA Interim Tier 4 and EU Stage 3A emissions certified Starting motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 kW/24 V Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 A/24 V Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Ah/2 x 12 V SWING SYSTEM Driven by . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic motor Swing reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Planetary gear Swing circle lubrication . . . . . . . . . . . . . . . . . . . . . . . Grease-bathed Swing lock . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical disc brake Swing speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 rpm
A B C D E F G H I J K L M N O P

DIMENSIONS
Boom Length Arm Length Overall length Overall height (to top of boom)* Overall width Overall height (to top of cab)* Ground clearance, counterweight Minimum ground clearance Tail swing radius Length of track on ground Track length Track gauge Width of crawler Shoe width Grouser height Machine cab height Machine cab width Distance swing center to rear end 3710 mm 12'2" 1650 mm 5'5" 5770 mm 18'11" 2555 mm 8'5" 2330 mm 2730 mm 735 mm 360 mm 1240 mm 2235 mm 2840 mm 1870 mm 2320 mm 450 mm 20 mm 1835 mm 2330 mm 1405 mm 7'8" 8'11" 2'5" 1'2" 4'1" 7'4" 9'4" 6'2" 7'7" 17.7" 0.8" 6'0" 7'8" 4'7" 3710 mm 2250 mm 6295 mm 2870 mm 12'2" 7'5" 20'8" 9'5"
2320 77" 120 4.7"

C(O)
1170 310"

139 47 5 "

DRIVES AND BRAKES Steering control . . . . . . . . . . . . . . . . . . . . . . . Two levers with pedals Drive method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic Maximum drawbar pull. . . . . . . . . . . . . . 66.9 kN 6820 kgf 15,050 lbf Maximum travel speed: High . . . . . . . . . . . . . . . . . 5.0 km/h 3.1 mph Low . . . . . . . . . . . . . . . . . 2.9 km/h 1.8 mph Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic lock Parking brake. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical disc

B* N F
G.L 470 17"

D* E H I M

L J K

* : Including grouser height

UNDERCARRIAGE Center frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-frame Track frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Box-section Seal of track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sealed track Track adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic Number of shoes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 each side Number of carrier rollers . . . . . . . . . . . . . . . . . . . . . . . . . 1 each side Number of track rollers . . . . . . . . . . . . . . . . . . . . . . . . . . 5 each side COOLANT AND LUBRICANT CAPACITY
(REFILLING)

WORKING RANGE
Boom Length Arm Length Maximum digging height Maximum dumping height Maximum digging depth Maximum vertical wall digging depth Maximum digging depth of cut for 2440 mm 8' level Maximum digging reach Maximum digging reach at ground Minimum digging reach at ground Minimum swing radius Bucket digging force Arm crowd force SAE Bucket digging force Arm crowd force 3710 mm 1650 mm 7300 mm 5180 mm 4100 mm 3610 mm 3770 mm 6380 mm 6240 mm 1900 mm 12'2" 5'5" 23'11" 17'0" 13'5" 11'10" 12'4" 20'11" 20'6" 6'3" 3710 mm 2250 mm 7600 mm 5500 mm 4710 mm 4030 mm 4430 mm 6920 mm 6790 mm 1735 mm 12'2" 7'5" 24'11" 18'1" 15'5" 13'3" 14'6" 22'8" 22'3" 5'8"
(m) 8 7 6 5

HYDRAULICS SYSTEM Type . . . . . . . . . . . . . . . . . . . . . . HydrauMind (Hydraulic Mechanical Intelligence New Design) system, Closed-center system with load-sensing valve and pressure-compensated valve Main pumps: Type . . . . . . . . . . . . . . . . . . . . Variable displacement, axial piston Maximum flow . . . . . . . . . . . . . . . . 160 ltr/min 42.3 U.S. gal/min Type (for machine with blade) . . . . . . . . . Fixed displacement gear Maximum flow . . . . . . . . . . . . . . . . . 63 ltr/min 16.6 U.S. gal/min Hydraulic motors: Travel . . . . . . . . . . . . . . . . . . . 2 x piston motor with parking brake Swing . . . . . . . . . . . . . . 1 x piston motor with swing holding brake Relief valve setting: Implement, travel circuit . . . . . . 26.5 MPa Swing circuit. . . . . . . . . . . . . . . 20.6 MPa Blade circuit (Raise) . . . . . . . . . 12.7 MPa (Lower) . . . . . . . . 21.1 MPa 270 kgf/cm2 210 kgf/cm2 130 kgf/cm2 215 kgf/cm2 3,840 psi 2,990 psi 1,850 psi 3,060 psi

A B C D E F G H I ISO

A B

4 3 2 1 G.L 0 1 245 9.6" 380 13"

Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . 125 ltr 33.0 U.S. gal Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ltr 2.6 U.S. gal Engine. . . . . . . . . . . . . . . . . . . . . 11.5 (11.0) ltr 3.0 (2.9) U.S. gal Final drive, each side . . . . . . . . . . . . . . . 1.1 ltr 0.3 U.S. gal Swing drive . . . . . . . . . . . . . . . . . . . . . . . 2.0 ltr 0.5 U.S. gal Hydraulic tank . . . . . . . . . . . . . . . . . 100 (56) ltr 26.4 (14.8) U.S. gal

OPERATING WEIGHT

(APPROXIMATE)

1750 mm 5'9" 61.3 kN 6250 kgf 13,780 lbf 41.5 kN 4230 kgf 9,330 lbf 53.3 kN 5440 kgf 11,990 lbf 38.1 kN 3890 kgf 8,570 lbf

2050 mm 6'9" 61.3 kN 6250 kgf 13,780 lbf 34.5 kN 3520 kgf 7,760 lbf 53.3 kN 5440 kgf 11,990 lbf 33.1 kN 3380 kgf 7,450 lbf

D C E

2 3 4 5 8 (m) 7 6 5 4

3 2 2440(8)

G F

Operating weight including 3710 mm 12'2" one-piece boom, 1650 mm 5'5" arm, SAE heaped 0.28 m3 0.37 yd3 backhoe bucket, blade, rated capacity of lubricants, coolant, full fuel tank, operator, and standard equipment. Shoes mm in 450 17.7" 600 23.6" 450 17.7" 600 23.6" Operating Weight kg lb 7365 16,240 7535 16,615 6945 15,315 7115 15,690 Ground Pressure kPa kg/cm2 psi 33.0 0.34 4.83 25.3 0.26 3.70 31.1 0.32 4.51 23.9 0.24 3.47

BACKHOE BUCKET AND ARM COMBINATION

Bucket Capacity (heaped) SAE, PCSA 0.09 m3 0.12 yd3 0.12 m3 0.16 yd3 0.20 m3 0.26 yd3 0.28 m3 0.37 yd3 0.34 m3 0.45 yd3 General digging CECE 0.08 m3 0.10 yd3 0.11 m3 0.14 yd3 0.18 m3 0.24 yd3 0.25 m3 0.33 yd3 0.30 m3 0.39 yd3 Without Side Cutters 350 mm 14" 450 mm 18" 550 mm 22" 650 mm 26" 755 mm 29.7" Width With Side Cutters 450 mm 18" 550 mm 22" 650 mm 26" 750 mm 30" NA X Not available Weight 145 kg 320 lb 160 kg 355 lb 185 kg 410 lb 210 kg 465 lb 210 kg 465 lb Number of Teeth 3 3 3 4 4 X X Arm Length 1650 mm 2250 mm 5'5" 7'5"

Hydraulic cylinders: (Number of cylinders bore x stroke x rod diameter) Boom . . . . . . . 1115 mm x 858 mm x 65 mm 4.5" x 33.8" x 2.6" Arm . . . . . . . . 1100 mm x 861 mm x 60 mm 3.9" x 33.9" x 2.4" Bucket . . . . . . 1 90 mm x 710 mm x 55 mm 3.5" x 28.0" x 2.2" Blade . . . . . . . 1130 mm x 130 mm x 65 mm 5.1" x 5.1" x 2.6"

With blade without blade

STANDARD EQUIPMENT Air cleaner, double element with auto dust evacuator Alternator, 35Ampere, 24V Automatic air conditioner Auto deceleration Batteries, 55Ah/2 x 12V Cab which includes: floor mat, intermittent front windshield wiper and washer, large ceiling hatch, pull-up front window, removable lower windshield Cooling fan, suction type Monitor panel Rear view mirrors (LH, rear) Seat belt 50mm 2" Shoes, 450mm 17.7" Triple grouser Starting motor 4.5kW Suspension seat Travel alarm Working lights 1 on cab 1 on boom

Light-duty operation

OPTIONAL EQUIPMENT Additional counter weight 220 kg 485 lb Additional working light on cab Arm, 1650mm 5'5" arm assembly Blade Boom, 3710mm 12'2" Hydraulic control unit 1 additional actuator Long arm, 2250mm 7'5" arm assembly Reinforced blade with BOC Seat belt 78mm 3" Shoes, 450mm 17.7" Road Liner 600mm 23.6" Triple grouser 450mm 17.7" Rubber shoe

10

11