Component - Plastics
File Number: E41179
MITSUBISHI ENGINEERING-PLASTICS CORP
ENVIRONMENT & QUALITY ASSURANCE DEPT
SHIODOME SUMITOMO-BLDG 25TH FL
1-9-2 HIGASHI-SHINBASHI
MINATO-KU, Tokyo 105-0021 Japan
Iupilon: S-3000(&6)(f1), S-3001(&6)(f1), S-3003(&6)(f1)
Polycarbonate (PC), pellets, powder, sheets, insulating material
(&6) - Suffix optional except V, DC and UDC.
(f1) - Suitable for outdoor use with respect to exposure to Ultraviolet Light, Water Exposure and Immersion in accordance with UL
746C.
Flammability Value Test Method
Flame Rating UL 94
3.0 mm, ALL HB
6.0 mm, ALL HB
0.38 mm, ALL V-2
1.5 mm, ALL V-2
1.8 mm, ALL V-2
Flammability Classification IEC 60695-11-10, -20
3.0 mm, ALL HB40
6.0 mm, ALL HB40
0.38 mm, ALL V-2
1.5 mm, ALL V-2
1.8 mm, ALL V-2
Electrical Value Test Method
Hot-wire Ignition (HWI) UL 746A
1.5 mm PLC 3
1.8 mm PLC 3
3.0 mm PLC 3
6.0 mm PLC 0
High Amp Arc Ignition (HAI) UL 746A
1.5 mm PLC 0
1.8 mm PLC 0
3.0 mm PLC 0
6.0 mm PLC 0
Comparative Tracking Index (CTI) PLC 2 UL 746A
Dielectric Strength 20 kV/mm ASTM D149
High Voltage Arc Tracking Rate (HVTR) PLC 0 UL 746A
Volume Resistivity 1.0E+7 ohms·cm ASTM D257
Volume Resistivity 1.0E+7 ohms·cm IEC 60093
Arc Resistance PLC 5 ASTM D495
Thermal Value Test Method
RTI Elec UL 746B
0.38 mm 80.0 °C
1.5 mm 125 °C
1.8 mm 125 °C
3.0 mm 125 °C
6.0 mm 125 °C
Page 1 of 2 Form Number: E41179-231971
UL LLC ©2025. All rights reserved. | www.ul.com Report Date: 10/26/1972
Last Revised: 8/8/2022 9:42:06 PM
ANSI/UL 94 small-scale test data does not pertain to building materials, furnishings and related contents. ANSI/UL 94
small-scale test data is intended solely for determining the flammability of plastic materials used in the components and parts
of end-product devices and appliances, where the acceptability of the combination is determined by UL.
Component - Plastics
File Number: E41179
Thermal Value Test Method
RTI Imp UL 746B
0.38 mm 80.0 °C
1.5 mm 115 °C
1.8 mm 115 °C
3.0 mm 115 °C
6.0 mm 115 °C
RTI Str UL 746B
0.38 mm 80.0 °C
1.5 mm 125 °C
1.8 mm 125 °C
3.0 mm 125 °C
6.0 mm 125 °C
Physical Value Test Method
Dimensional Change 0.0 % ASTM D1042
Dimensional Change 0.0 % ISO 2796
Outdoor Suitability f1 UL 746C
Notice of Disclaimer
By accessing this Yellow Card data information sheet and the database from which this information was generated (the “Yellow Card”), the user
acknowledges and accepts the terms and conditions upon which this Yellow Card is made available. This Yellow Card, the database from which it was
generated, and all related materials, support, and services, are made available by UL for use only by permission and "as is", without any representation
or warranty of any kind, express or implied, including but not limited to any implied warranties of merchantability, fitness for a particular purpose or that
the products identified in this Yellow Card will satisfy the user’s requirements. UL cannot and does not warrant that the data contained in this Yellow
Card is current, accurate, or complete. The user must independently confirm the conformance of any product to the applicable standards or
requirements with the manufacturer of that product. Permission to access this Yellow Card may be withdrawn at any time by UL in its sole discretion.
The identification of products and companies on this Yellow Card does not in any way imply endorsement of those products or companies by UL. UL
does not assume and expressly disclaims, liability to any person for any loss or damage (including lost profits, lost savings, or any indirect, special,
incidental, consequential or punitive damages whether or not UL has been advised of the possibility of such damages) arising out of, or in connection
with, the use of this Yellow Card regardless of the cause or causes of such loss or damage.
Page 2 of 2 Form Number: E41179-231971
UL LLC ©2025. All rights reserved. | www.ul.com Report Date: 10/26/1972
Last Revised: 8/8/2022 9:42:06 PM
ANSI/UL 94 small-scale test data does not pertain to building materials, furnishings and related contents. ANSI/UL 94
small-scale test data is intended solely for determining the flammability of plastic materials used in the components and parts
of end-product devices and appliances, where the acceptability of the combination is determined by UL.
