3/22/25, 5:51 PM Introduction to Abrasive Machining and Finishing Processes - - Unit 6 - Week 3: Honing, Lapping and Super Finishing.

(https://swayam.gov.in) (https://swayam.gov.in/nc_details/NPTEL)

[email protected] 

NPTEL (https://swayam.gov.in/explorer?ncCode=NPTEL) » Introduction to Abrasive Machining and Finishing

Processes (course)


Click to register
for Certification
exam
Week 3: Assignment 3
(https://examform.nptel.ac.in/2025_01/exam_form/dashboard)
The due date for submitting this assignment has passed.

If already Due on 2025-02-12, 23:59 IST.

registered, click
to check your Assignment submitted on 2025-02-12, 20:53 IST
payment status
1) In which of the condition(s) power stroking of hone is recommended 1 point
(i) In mass production of small parts
(ii) When workpiece need to be fixed
Course (iii) Can be used for honing virtually all types of workpieces
outline
(i) alone
(ii) alone
About
NPTEL () (i) and (ii)
(i), (ii), and (iii)
How does an Yes, the answer is correct.
NPTEL Score: 1
online Accepted Answers:
course (i), (ii), and (iii)
work? ()
2) What factor(s) will affect honing 1 point
Week 1:
Introduction Machine controls
to Machine structure
Conventiona
Honing stones
l Abrasive
Processes () All of these

Yes, the answer is correct.

Week 2: Score: 1
Sustainable Accepted Answers:
All of these

https://onlinecourses.nptel.ac.in/noc25_me40/unit?unit=28&assessment=119 1/4
3/22/25, 5:51 PM Introduction to Abrasive Machining and Finishing Processes - - Unit 6 - Week 3: Honing, Lapping and Super Finishing.

Grinding
3) In honing process cylindricity, material removal rate, honing trajectory is primarily 1 point
Process ()
determined by
(i) Machine tool characteristics
Week 3:
Honing, (ii) Honing head structure
Lapping and (iii) Cylinder structure and material properties
Super (iv) Honing process parameters
Finishing. () (v) Effect of initial cylindricity, which is previously generated by boring operation

Lec. 1 : (i), (ii), (iii) only

Honing (iii), (v) only
Process (unit?
(i), (ii), (iii), (iv) and (v)
unit=28&lesso
n=29) (ii), (iii), (iv) and (v)

Lec. 2 : Yes, the answer is correct.

Score: 1
Lapping
Process (unit?
Accepted Answers:
unit=28&lesso
(i), (ii), (iii), (iv) and (v)
n=30)
4) Material selection, grain size, and density of honing stones have great influence on 1 point
Lec. 3 : Super
the
Finishing and
Sand Blasting Surface roughness achieved
(unit?
unit=28&lesso
Material removal rate
n=31) Circularity of the hole

Quiz: Week 3: Strength of the hallow feature to be polished

Assignment 3 Yes, the answer is correct.
(assessment? Score: 1
name=119) Accepted Answers:
Material removal rate
Week 3
Feedback
Form : 5) The crosshatch angle in honing when reciprocating and rotational speed of the hone1 point
Introduction to is same
Abrasive
Machining and 0°
Finishing 30°
Processes!!
45°
(unit?
unit=28&lesso 90°
n=32)
No, the answer is incorrect.
Score: 0
Week 4 : Accepted Answers:
Conventiona 45°
l Abrasive
Process and
6) Which of the following are true with respect to the characteristics of the lapping 1 point
Surface
process
Integrity in
i. It uses loose abrasives between lap and the workpiece
Abrasive
ii. Lap and workpieces are not positively driven but are guided in contact with each other
Process ()
iii. Relative motion between the lap and the workpiece should change continuously so that
path of abrasive grains of the lap is not repeated on the workpiece
Week 5 :
Advanced iv. Relative motion between the lap and the workpiece should not change continuously so
Abrasive that path of abrasive grains of the lap is repeated on the workpiece

https://onlinecourses.nptel.ac.in/noc25_me40/unit?unit=28&assessment=119 2/4
3/22/25, 5:51 PM Introduction to Abrasive Machining and Finishing Processes - - Unit 6 - Week 3: Honing, Lapping and Super Finishing.

Machining (i), (ii), (iii)

Processes ()
(i), (ii), (iv)

Week 6 : (i) only

Hybrid (ii) and (iv)
Abrasive
Yes, the answer is correct.
Machining Score: 1
Processes () Accepted Answers:
(i), (ii), (iii)
Week 7 :
Advanced 7) Which of the following are used as lapping medium 1 point
Abrasive
Water
Finishing
Processes-1 Grease
() Water, oil
Water, grease or oil
Week 8 :
Advanced Yes, the answer is correct.
Score: 1
Abrasive
Accepted Answers:
Finishing
Water, grease or oil
Processes-2
()
8) Which of the following statements are true with respect to abrasive slurries used in 1 point
lapping process
Download
(i) Water soluble slurries are preferred to avoid health hazards
Videos ()
(ii) Oil – water emulsions has shorter shelf life then oil – soluble emulsions
(iii) Oil has tendency to penetrate into the pores of some workpiece material
Text
(iv) Oil – water emulsions has shelf life then oil – soluble emulsions
Transcripts
()
(i), (iii), (iv)
(i), (ii)
Lecture
Notes () (ii) only
(i), (ii), (iii)
Books ()
Yes, the answer is correct.
Score: 1
Accepted Answers:
(i), (ii), (iii)

9) What are the advantages of lapping process 1 point

(i) High accurate surface geometry
(ii) Good quality and repeatability
(iii) Required tolerance achieved
(iv) No warping of the component
(v) No heat generation and thermal damage

(i), (ii), (iv), (v)

(i), (iv), (v)
(i), (ii), (iii), (iv), (v)
(ii), (iv), (v)

Yes, the answer is correct.

https://onlinecourses.nptel.ac.in/noc25_me40/unit?unit=28&assessment=119 3/4
3/22/25, 5:51 PM Introduction to Abrasive Machining and Finishing Processes - - Unit 6 - Week 3: Honing, Lapping and Super Finishing.

Score: 1
Accepted Answers:
(i), (ii), (iii), (iv), (v)

10) Which of the following process is classified under dry sand blasting 1 point

Air pressure blasting

Hydro blast process
Vapor blast process
Both hydro blast and vapor blast

Yes, the answer is correct.

Score: 1
Accepted Answers:
Air pressure blasting

https://onlinecourses.nptel.ac.in/noc25_me40/unit?unit=28&assessment=119 4/4