LC230W02

Liquid Crystal Display

Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ) Final Specification

Title 23” WXGA TFT LCD

BUYER General SUPPLIER LG.Philips LCD CO., Ltd.

MODEL *MODEL LC230W02

SUFFIX A5K4

*When you obtain standard approval,

please use the above model name without suffix

SIGNATURE SIGNATURE
DATE DATE
APPROVED BY
APPROVED BY

/ Jay Yoon / G.Manager

REVIEWED BY

/ J.M Kim / Manager

PREPARED BY
/ Y.J Kim / Engineer

Please return 1 copy for your confirmation with TV Products Engineering Dept.
your signature and comments. LG. Philips LCD Co., Ltd

Ver. 1.0 FEB.16, 2005 1 / 28

 LC230W02
Liquid Crystal Display
Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ) Final Specification

Title 23” WXGA TFT LCD

BUYER LGE DID SUPPLIER LG.Philips LCD CO., Ltd.

MODEL *MODEL LC230W02

SUFFIX A5K4

*When you obtain standard approval,

please use the above model name without suffix

SIGNATURE SIGNATURE
DATE DATE
APPROVED BY
APPROVED BY

/ Jay Yoon / G.Manager

REVIEWED BY

/ J.M Kim / Manager

PREPARED BY
/ Y.J Kim / Engineer

Please return 1 copy for your confirmation with TV Products Engineering Dept.
your signature and comments. LG. Philips LCD Co., Ltd

Ver. 1.0 FEB.16, 2005 2 / 28

 LC230W02
Liquid Crystal Display
Product Specification

CONTENTS

NO. ITEM Page

- COVER 1

- CONTENTS 2

- RECORD OF REVISIONS 3

1 GENERAL DESCRIPTION 4

2 ABSOLUTE MAXIMUM RATINGS 5

3 ELECTRICAL SPECIFICATIONS 6

1 ELECTRICAL CHARACTREISTICS 6

2 INTERFACE CONNECTIONS 8

3 SIGNAL TIMING SPECIFICATIONS 12

4 SIGNAL TIMING WAVEFORMS 13

5 COLOR INPUT DATA REFERENCE 14

6 POWER SEQUENCE 15

4 OPTICAL SPECIFICATIONS 17

5 MECHANICAL CHARACTERISTICS 21

6 RELIABLITY 24

7 INTERNATIONAL STANDARDS 25

1 SAFETY

2 EMC

8 PACKING 26

1 DESIGNATION OF LOT MARK

2 PACKING FORM

9 PRECAUTIONS 27

Ver. 1.0 FEB.16, 2005 3 / 28

 LC230W02
Liquid Crystal Display
Product Specification

RECORD OF REVISIONS

Revision
Date Page Description
No.
Ver 1.0 FEB.16, 2004 Model Modify(Add Inverter Reset curcuit)
(LC230W02-A5K1=>LC230W02-A5K4)
Final

Ver. 1.0 FEB.16, 2005 4 / 28

 LC230W02
Liquid Crystal Display
Product Specification

1. General Description
The LC230W02 is a Color Active Matrix Liquid Crystal Display with an integral External
Electrode Fluorescent Lamp(EEFL) backlight system. The matrix employs a-Si Thin Film
Transistor as the active element. It is a transmissive type display operating in the normally
black mode. This TFT-LCD has a 23.0 inch diagonally measured active display area with
WXGA resolution (768 vertical by 1366 horizontal pixel array). Each pixel is divided into
Red,Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or
the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot,
thus, presenting a palette of more than 16,7M(True) colors. The LC230W02 has been
designed to apply the LVDS interface. It is intended to support LCD TV, PCTV where high
brightness, super wide viewing angle, high color gamut, high color depth, and fast response
time are important.

RGB(Mini-LVDS)
Source Driver Circuit
S1 S1366
G1
Gate Driver Circuit

+12.0V
Timing Controller
LVDS CN1
5pair [LVDS Rx & Mini-LVDS

Option
(30pin) Tx integrated]
TFT - LCD Panel
#9 (1366 RGB 768 pixels)

Power G768
Circuit Block

+24.0V 2pin x 1CNs (High)

Inverter Back light Assembly
+24.0V (CN2,CN3) 2pin x 1CNs (High) (15EEFL)

Figure 1. Block diagram

General Features
Active screen size 22.95 inches(582.96mm) diagonal
Outline Dimension 559.8(H) x 333.8(V) x 45.2(D) mm(Typ.)
Pixel Pitch 0.372 mm x 0.124 mm x RGB

Pixel Format 1366 horizontal by 768 vertical pixels. RGB stripe arrangement
Interface LVDS 1port
Color depth 8-bit, 16,777,216 colors
Luminance, white 500 cd/m2 ( Center 1 point, Typ. )
Viewing Angle (CR>10) Viewing Angle Free(R/L 176(Typ.), U/D 176(Typ.))
Power Consumption Total 59.1 Watt(Typ.), (3.9 Watt @VLCD, 55.2 Watt @VBL)
Weight 4200 g (Typ.)
Display operating mode Transmissive mode, normally black
Surface treatments Hard coating (3H), Anti-glare treatment of the front polarizer

Ver. 1.0 FEB.16, 2005 5 / 28

 LC230W02
Liquid Crystal Display
Product Specification

2. Absolute Maximum Ratings

Table 1. Absolute Maximum Ratings

Value
Parameter Symbol Unit Note
Min Max

Power Supply VLCD -0.3 +14 Vdc

At 25
Input Voltage VBL -0.3 +27 Vdc

On/Off Control Voltage ON/OFF -0.3 +5.25 Vdc

Brightness Control Voltage VBR 0 +3.3 Vdc

Operating Temperature TOP 0 +40 C 1

Storage Temperature TST -20 +50 C 1
Operating Ambient Humidity HOP 10 90 %RH 1
Storage Humidity HST 10 90 %RH 1

Note :
1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 C Max, and no condensation.

Figure 2. Temperature and relative humidity

Ver. 1.0 FEB.16, 2005 6 / 28

 LC230W02
Liquid Crystal Display
Product Specification

3. Electrical Specifications
The LC230W02 requires two power inputs. One is employed to power the LCD electronics and
to drive the TFT array and liquid crystal. The second input power for the EEFL/Backlight, is to
power the inverter.

3-1. Electrical Characteristics

Table 2. Electrical Characteristics
Value
Parameter Symbol Unit Note
Min Typ Max
1. Power for Panel:
Power Supply Input Voltage VLCD 11.4 12.0 12.6 Vdc
- 325 420 mA 1
Power Supply Input Current ILCD
- 390 510 mA 2
Power Consumption PLCD - 3.90 5.04 Watt 1
Inrush Current (VLCD Input) IRUSH - - 3 A 3

Notes:
1. The specified current and power consumption are under
the VLCD=12V, 25 C, fV(frame frequency)=60Hz condition.
Typical supply current is measured at the condition of 8 X 6 Mosaic pattern(white black)
shown in the [ Figure 3 ] is displayed.

2. The current is specified at the maximum current pattern.

3. The duration of rush current is about 2ms and rising time of power input is 1ms(min).

[ Figure 3 ]
Mosaic pattern : for power consumption measurement

Ver. 1.0 FEB.16, 2005 7 / 28

 LC230W02
Liquid Crystal Display
Product Specification

Table 3. Inverter Electrical Characteristics

Value Note
Parameter Symbol Condition Unit
Min Typ Max
2. Power for Inverter
Power supply Input Voltage VBL 22.8 24.0 25.2 Vdc 1
Power supply Input Current IBL VBR-B = 3.3V - 2.3 2.7 A 1
Power Consumption PBL VBR–B =3.3V - 55.2 64.8 Watt 1
Back-Light H (Lamp ON) 2.4 - 5.0 Vdc
ON/OFF
ON/OFF Control voltage L (Lamp OFF) 0.0 - 0.6 Vdc
Brightness Adj. VBR 0 - 3.3 Vdc

Inrush Current (VBL Input) IRUSH - - - 5 A 2

Lamp Lifetime 50,000 - Hrs 3

Note :
1. The specified current and power consumption are under the typical supply input voltage, 24.0V.
The ripple voltage of the power supply input voltage is under 0.5 Vp-p.

2. The duration of rush current is about 2ms and rising time of power input is 1ms(min).

3. The life is determined as the time at which luminance of the lamp is

50% compared to that of initial value at the typical lamp current on condition of continuous
operating at 25 ± 2 C.

Ver. 1.0 FEB.16, 2005 8 / 28

 LC230W02
Liquid Crystal Display
Product Specification

3-2. Interface Connections

This LCD employs two kinds of interface connections. A 30 pin connector is used for LCD
electronics and a 12pin connector is used for the integral backlight system.

3-2-1. Signal Interface

The LCD connector(CN1) : FI-X30SSL-HF (Manufactured by JAE) or Equivalent.
The pin configuration for the 30 pin connector is shown in the table below.

Table 4. 30Pin Connector pin configuration (For LCD Panel)

Pin Signal assignment Pin Signal assignment

1 VLCD (12V) 16 LVDS SIGNAL CHANNEL 1+
2 VLCD (12V) 17 GND
3 VLCD (12V) 18 LVDS SIGNAL CHANNEL 2-
4 VLCD (12V) 19 LVDS SIGNAL CHANNEL 2+
5 GND 20 GND
6 GND 21 LVDS CLOCK C-
7 GND 22 LVDS CLOCK C+
8 GND 23 GND
9 DISM (Note 1) 24 LVDS SIGNAL CHANNEL 3-
10 NC 25 LVDS SIGNAL CHANNEL 3+
11 GND 26 GND
12 LVDS SIGNAL CHANNEL 0- 27 NC
13 LVDS SIGNAL CHANNEL 0+ 28 NC
14 GND 29 GND
15 LVDS SIGNAL CHANNEL 1- 30 GND

1 - Part/No. : FI-X30SSL-HF(JAE)
30
- Mating connector : FI-30C2L
(Manufactured by JAE) or compatible

Rear view of LCM

Notes:
1. If pin9 is ground, interface format is “LG”, and if pin9 is 3.3V, interface format is “DISM.
(See page 9~10)
2. All GND(ground) pins should be connected together and should also be
connected to the LCD’s metal frame.
3. All power input pins should be connected together.
4. Input level of LVDS signal is based on the IEA664 standard.
5. The pin30 should be ground, this pin is necessary for LPL’s test

Ver. 1.0 FEB.16, 2005 9 / 28

 LC230W02
Liquid Crystal Display
Product Specification

Table 5.
Required signal assignment for LVDS transmitter (Pin9 = “L” or open)

Host System DS90C385 Timing

24 Bit or Compatible FI-X30SSL-HF Controller
RED0 51
48
RED1 52 TxOUT0- 12 RxIN0-
47 100
RED2 54 TxOUT0+ 13 RxIN0+
RED3 55
RED4 56
46
RED5 3 TxOUT1- 15 RxIN1-
45 100
RED6 50 TxOUT1+ 16 RxIN1+
RED7 2
GREEN0 4
42
GREEN1 6 TxOUT2- 18 RxIN2-
41 100
GREEN2 7 TxOUT2+ 19 RxIN2+
GREEN3 11
GREEN4 12
40
GREEN5 14 TxCLKOUT- 21 RxCLKIN-
39 100
GREEN6 8 TxCLKOUT+ 22 RxCLKIN+
GREEN7 10
BLUE0 15
38
BLUE1 19 TxOUT3- 24 RxIN3-
37 100
BLUE2 20 TxOUT3+ 25 RxIN3+
BLUE3 22
BLUE4 23 9 LG / DISM
BLUE5 24 30 LCD Test
BLUE6 16
BLUE7 18
Hsync 27
GND
GND

Vsync 28
Data Enable 30
LCD Module
CLOCK 31

Note:
1. The LCD module uses a 100 Ohm( ) resistor between positive and negative lines
of each receiver input.
2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.

Ver. 1.0 FEB.16, 2005 10 / 28

 LC230W02
Liquid Crystal Display
Product Specification

Table 6.
Required signal assignment for LVDS transmitter (Pin9 = “H” )

Host System DS90C385 Timing

24 Bit or Compatible FI-X30SSL-HF Controller
RED0 50
48
RED1 2 TxOUT0- 12 RxIN0-
47 100
RED2 51 TxOUT0+ 13 RxIN0+
RED3 52
RED4 54
46
RED5 55 TxOUT1- 15 RxIN1-
45 100
RED6 56 TxOUT1+ 16 RxIN1+
RED7 3
GREEN0 8 42
GREEN1 10 TxOUT2- 18 RxIN2-
41 100
GREEN2 4 TxOUT2+ 19 RxIN2+
GREEN3 6
GREEN4 7
40
GREEN5 11 TxCLKOUT- 21 RxCLKIN-
39 100
GREEN6 12 TxCLKOUT+ 22 RxCLKIN+
GREEN7 14
BLUE0 16
38
BLUE1 18 TxOUT3- 24 RxIN3-
37 100
BLUE2 15 TxOUT3+ 25 RxIN3+
BLUE3 19
BLUE4 20 9 LG / DISM
BLUE5 22 30 LCD Test
BLUE6 23
BLUE7 24
Hsync 27
GND

Vsync 28
Vcc

Data Enable 30
LCD Module
CLOCK 31

Note:
1. The LCD module uses a 100 Ohm( ) resistor between positive and negative lines
of each receiver input.
2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.

Ver. 1.0 FEB.16, 2005 11 / 28

 LC230W02
Liquid Crystal Display
Product Specification

3-2-2. Inverter Connector for Backlight

The inverter connector is S12B-PH-SM3 (manufactured by JST) or equivalent

The pin configuration for the 12 pin connector is shown in the table below.

Table 7. 12Pin Connector Pin Configuration (For Inverter Connector)

Pin Symbol Signal assignment Note
Master(CN2) Slave(CN3)
1 VBL 24V Power Input VBL VBL

2 VBL 24V Power Input VBL VBL

3 VBL 24V Power Input VBL VBL

4 VBL 24V Power Input VBL VBL

5 VBL 24V Power Input VBL VBL

6 GND GROUND GND GND

7 GND GROUND GND GND

8 GND GROUND GND GND 1

9 GND GROUND GND GND

10 GND GROUND GND GND

11 VBR-B Burst dimming VBR-B Don’t care 0V ~ 3.3V

Backlight ON : 2.4 ~ 5.0V

12 ON/OFF ON/OFF Don’t care
ON/OFF control OFF : 0.0 ~ 0.6V

Rear view of LCM

PCB
1. Connector
1) Connector(Receptacle)
12
: S12B-PH-SM3 (JST) or its equivalent 12
2) Mating Connector(Plug)
…
…

: PHR12 (JST) or its equivalent

* JST : Japan solderless Terminal Co.,Ltd. 1 1

S12B-PH-SM3

Notes : Pin 1~10 should connect to master and slave connector.

1. GROUND is connected to the LCD’s metal frame.

Ver. 1.0 FEB.16, 2005 12 / 28

 LC230W02
Liquid Crystal Display
Product Specification

3-3. Signal Timing Specifications

This is the signal timing required at the input of the LVDS transmitter. All of the interface
signal timing should be satisfied with the following specifications for it’s proper operation.

Table 8. Timing Table

ITEM SYMBOL Min. Typ. Max. Unit Note

Period tCLK 12.5 13.8 14.7 ns

Clock
Frequency fCLK 68 72.3 80 MHz

Horizontal total tHT 1416 1528 1776 Pixel

Hsync Hsync frequency fH 45.0 47.4 50 KHz

Hsync width tWH 8 32 - Pixel

Vertical total tVT 775 790 1063 Line PAL :
47~53Hz,
Vsync Vsync frequency fV 47 60 63 Hz
NTSC :
Vsync width tWV 2 5 - Line 57~63Hz
Horizontal valid tHV 1366 1366 1366
Horizontal
tHBP 24 80 -
back porch
Pixel
Horizontal
tHFP 16 48 -
front porch
Horizontal blank - 48 160 tHP- tHV
DE
Vertical valid tVV 768 768 768
Vertical
tVBP 4 15 -
back porch
Line
Vertical
tVFP 1 2 -
front porch
Vertical blank - 7 22 tVP- tVV

Note:
Hsync period and Hsync width-active should be even number times of tCLK. If the value is
odd number times of tCLK, display control signal can be asynchronous.
In order to operate this LCM a Hsync.,Vsync and DE(data enable) signals should be used.
1. The performance of the electro-optical characteristics are may be influenced by
variance of the vertical refresh rates.
2. Vsync, Hsync should be keep the above specification.

Ver. 1.0 FEB.16, 2005 13 / 28

 LC230W02
Liquid Crystal Display
Product Specification

3-4. Signal Timing Waveforms

0.7Vcc
Hsync, Vsync, DE, Data
0.3Vcc

tCLK
DCLK 0.5 Vcc

Valid data

Invalid data Invalid data

DE(Data Enable)

tHP
HSync tWH

tHBP tHV tHFP

DE(Data Enable)

tVP
tWV

VSync
tVBP tVV tVFP

DE(Data Enable)

Ver. 1.0 FEB.16, 2005 14 / 28

 LC230W02
Liquid Crystal Display
Product Specification

3-5. Color Input Data Reference

The brightness of each primary color (red,green and blue) is based on the 8-bit gray scale data
input for the color ; the higher the binary input, the brighter the color.
The table below provides a reference for color versus data input.

Table 9. Color Data Reference

Ver. 1.0 FEB.16, 2005 15 / 28

 LC230W02
Liquid Crystal Display
Product Specification

3-6. Power Sequence

3-6-1. Sequence for LCD Module

90% 90%
Power Supply
(VLCD : 12V) 10%
10%
T1
T6

T2 T5
Interface Signal
(LVDS Data Valid Data
with H,Vsync and DE)

T3 T4

Power Supply for

LAMP ON
Backlight Inverter
LAMP OFF LAMP OFF

Table 10. Power Sequence for LCM

Value
Parameter Unit
Min Typ Max
T1 0.01 - 10 ms
T2 0.01 - 50 ms
T3 200 - - ms
T4 200 - - ms
T5 0.01 - 50 ms
T6 2000 - - ms

Notes :
1. Please avoid floating state of interface signal at invalid period.
2. When the interface signal is invalid, be sure to pull down the power supply for
LCD VLCD to 0V.
3. Lamp power must be turn on after power supply for a LCD interface signal are valid.
4. T6 should be measured after the module has been fully discharged between power off
and on period.

Ver. 1.0 FEB.16, 2005 16 / 28

 LC230W02
Liquid Crystal Display
Product Specification

3-6-2. Sequence for Inverter

90%
Power Supply
For Inverter
(VBL: 24V) 10% 0.7V

T3
T1
T5

T2
T2
On/Off Control
(0~5V)

T4 T4
Brightness Adj.
VBR : (0~3.3V)

3-6-3. Deep condition for Inverter

VBL : 24V

VBL(Typ.) x 0.85

0V

Table 11. Power Sequence for Inverter

Value
Parameter Unit Note
Min Typ Max
T1 20 - - ms
T2 100 - - ms
T3 200 - - ms 1
T4 0 - - ms
T5 10 - - ms
T6 - - 10 ms

Ver. 1.0 FEB.16, 2005 17 / 28

 LC230W02
Liquid Crystal Display
Product Specification

4. Optical Specification

Optical characteristics are determined after the unit has been ‘ON’ for 30Min in a dark
environment at 25 2 C. The values specified are at an approximate distance 50cm from the
LCD surface at a viewing angle of Φ and θ equal to 0 .
FIG. 4 presents additional information concerning the measurement equipment and method.

Optical Stage(x,y)
LCD Module

Field = 1
Pritchard PR880
or equivalent

50Cm

[Figure 4] Optical characteristic measurement equipment and method

Table 12. Optical characteristics (Ta=25 2 C, VLCD=12V, fV=60Hz, CLK=72.3MHz, VBR=3.3V)

Value
Parameter Symbol Unit Note
Min Typ Max
Contrast Ratio CR 400 550 1
Surface Luminance, white LWH 400 500 cd/m2 2
Luminance Variation δ WHITE - 1.3 3
Response Rise Time TrR 7 15
ms 4
Time Decay Time TrD 9 15
Color Coordinates
RED RX 0.640
RY 0.343
GREEN GX 0.292
GY Typ – 0.607 Typ
BLUE BX 0.03 0.147 +0.03
BY 0.067
WHITE WX 0.285
WY 0.293
Viewing Angle (CR>10)
x axis, right(φ=0 ) θr 85 89 -
x axis, left (φ=180 ) θl 85 89 - degree 5
y axis, up (φ=90 ) θu 85 89 -
y axis, down (φ=270 ) θd 85 89 -
Gray scale 6

Ver. 1.0 FEB.16, 2005 18 / 28

 LC230W02
Liquid Crystal Display
Product Specification

Note :

1. Contrast ratio(CR) is defined mathematically as :

Surface luminance with all white pixels

Contrast ratio = ---------------------------------------------------------
Surface luminance with all black pixels

It is measured at center point(1)

2. Surface luminance(LWH) is luminance value at center point (P1) across the LCD surface 50cm
from the surface with all pixels displaying white.
For more information see FIG 5.

3. The variation in surface luminance , δ WHITE is defined as

δ WHITE = Maximum (P1,P2, …..,P5) / Minimum (P1,P2, …..,P5)

For more information see [ Figure 5 ].

<Measuring point for surface luminance and luminance variation>

H

A : H / 4 mm
B : V / 4 mm
P2 P3 H : 508.152 mm
V : 285.696 mm
@ H,V : Active Area
P1
V

P4 P5

Figure 5. Luminance measuring point

Ver. 1.0 FEB.16, 2005 19 / 28

 LC230W02
Liquid Crystal Display
Product Specification

4. The response time is defined as the following figure and shall be measured by
switching the input signal for “Black” and “White”.

TrR TrD
100%
90%

Optical
Response Black White Black

10%
0

Figure 6. Response time

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis
which is normal to the LCD surface. For more information see Figure 7 .

<Dimension of viewing angle range>

Normal
E Y
φ = 90°, Up

φ = 180°, Left
θ

φ = 0°, Right

φ = 270°, Down

Figure 7. Viewing angle

Ver. 1.0 FEB.16, 2005 20 / 28

 LC230W02
Liquid Crystal Display
Product Specification

6. Gray scale specification

Table 13. Gray scale

Gray Level Luminance [%] (Typ)

L0 0.15
L15 0.23
L31 0.74
L47 1.91
L63 3.95
L79 6.91
L95 10.9
L111 15.6
L127 20.7
L143 27.0
L159 34.7
L175 43.6
L191 53.1
L207 63.9
L223 75.6
L239 90.9
L255 100

Ver. 1.0 FEB.16, 2005 21 / 28

 LC230W02
Liquid Crystal Display
Product Specification

5. Mechanical Characteristics

Table 11. provides general mechanical characteristics for the model LC230W02. In addition,
the figures in the next page are detailed mechanical drawing of the LCD.

Table 14. Mechanical characteristics

Horizontal 559.8 mm

Outline Dimension Vertical 333.8 mm

Depth 45.2 mm

Horizontal 513.0 mm
Bezel Area
Vertical 290.6 mm

Horizontal 508.152 mm
Active Display Area
Vertical 285.696 mm

Weight 4200 g (Typ.), 4450 g (Max.)

Hard coating(3H)
Surface Treatment
Anti-glare treatment of the front polarizer

Notes : Please refer to a mechanic drawing in terms of tolerance at the next page.

Ver. 1.0 FEB.16, 2005 22 / 28

 LC230W02
Liquid Crystal Display
Product Specification

<FRONT VIEW>

Ver. 1.0 FEB.16, 2005 23 / 28

 LC230W02
Liquid Crystal Display
Product Specification

<REAR VIEW>

Ver. 1.0 FEB.16, 2005 24 / 28

 LC230W02
Liquid Crystal Display
Product Specification

6. Reliability

Environment test condition

No Test Item Condition

1 High temperature storage test 50 C, 240hrs

2 Low temperature storage test -20 C, 240hrs

3 High temperature operation test 40 C, 50%RH, 240hrs

4 Low temperature operation test 0 C, 240hrs

Wave form : random

Vibration level : 1.0Grms
Vibration test
5 Bandwidth : 10-500Hz
(non-operating)
Duration : X,Y,Z, 10 min
One time each direction
Shock level : 100Grms
Shock test Waveform : half sine wave, 2ms
6
(non-operating) Direction : X, Y, Z
One time each direction

7 Humidity condition Operation Ta= 40 C ,90%RH

Altitude operating 0 - 14,000 feet(4267.2m)

8
storage / shipment 0 - 40,000 feet(12192m)

Ver. 1.0 FEB.16, 2005 25 / 28

 LC230W02
Liquid Crystal Display
Product Specification

7. International Standards

7-1. Safety
a) UL 60950, Third Edition, Underwriters Laboratories, Inc., Dated Dec. 11, 2000.
Standard for Safety of Information Technology Equipment, Including Electrical Business
Equipment.

b) CAN/CSA C22.2, No. 60950, Third Edition, Canadian Standards Association, Dec. 1, 2000.
Standard for Safety of Information Technology Equipment, Including Electrical Business
Equipment.

c) EN 60950 : 2000, Third Edition

IEC 60950 : 1999, Third Edition
European Committee for Electro technical Standardization(CENELEC)
EUROPEAN STANDARD for Safety of Information Technology Equipment Including
Electrical Business Equipment.

7-2. EMC

a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical

and Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards
Institute(ANSI),1992

b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of

Information Technology Equipment.“ International Special Committee on Radio Interference.

c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of

Information Technology Equipment.“ European Committee for Electro technical
Standardization.(CENELEC), 1998( Including A1: 2000 )

Ver. 1.0 FEB.16, 2005 26 / 28

 LC230W02
Liquid Crystal Display
Product Specification

8. Packing

8-1. Designation of Lot Mark

A B C D E F G H I J K L M

A,B,C : Inch
D : Year
E : Month
F : Panel Code
G : Factory Code
H : Assembly Code
I,J,K,L,M : Serial No

Note
1. Year

Year 97 98 99 2000 2001 2002 2003 2004 2005 2006 2007

Mark 7 8 9 0 1 2 3 4 5 6 7

2. Month

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Mark 1 2 3 4 5 6 7 8 9 A B C

3. Panel Code

Panel Code P1 Factory P2 Factory P3 Factory P4 Factory P5 Factory Hydis Panel

Mark 1 2 3 4 5 H

4. Factory Code

Factory Code LPL Gumi LPL Nanjing

Mark K C

5. Serial No

Serial No. 1 ~ 99,999 100,000 ~

A0001 ~ A9999, - - - - ,
Mark 00001 ~ 99999
Z9999

8-2. Packing Form

a) Package quantity in one box : 4 pcs

b) Box size : 439mm X 350mm X 665mm.

Ver. 1.0 FEB.16, 2005 27 / 28

 LC230W02
Liquid Crystal Display
Product Specification

9. Precautions
Please pay attention to the following when you use this TFT LCD module.

9-1. Mounting Precautions

(1) You must mount a module using holes arranged in side and rear.
(2) You should consider the mounting structure so that uneven force(ex. twisted stress) is
not applied to the module. And the case on which a module is mounted should have
sufficient strength so that external force is not transmitted directly to the module.
(3) Please attach a transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to
the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not describe because
the former generates corrosive gas of attacking the polarizer at high temperature and
the latter causes circuit break by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder
than HB pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer with bare hand or greasy cloth.
(Some cosmetics are determined to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or
other soft materials like chamois soaks with petroleum benzine. Normal-hexane is
recommended for cleaning the adhesives used to attach front / rear polarizers.
Do not use acetone, toluene and alcohol because they cause chemical damage to the
polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer
causes deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.

9-2. Operating Precautions

(1) The spike noise causes the mis-operation of circuits. It should be lower than
following voltage : V= 200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after
turned on)becomes longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage
to polarizer or electrical contacted parts. And after fading condensation,
smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference shall be done by system manufacturers. Grounding and shielding methods
may be important to minimized the interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can
not be operated its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw
(if not, it causes metal foreign material and deals LCM a fatal blow)
(9) Please do not set LCD on its edge.

Ver. 1.0 FEB.16, 2005 28 / 28

 LC230W02
Liquid Crystal Display
Product Specification

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge.

Make certain that treatment persons are connected to ground through wrist band etc. And
don’t touch interface pin directly.

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep
the temperature between 5 C and 35 C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and
polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and
with well ion-blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there
remains a very small amount of glue still on the Bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the Bezel or its vestige is
recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked
with normal-hexane.

Ver. 1.0 FEB.16, 2005 29 / 28