Scribd
Upload
22 views5 pages

Assignment 2 - Edit

Uploaded by

Ngô Kim Long
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
22 views5 pages

Assignment 2 - Edit

Uploaded by

Ngô Kim Long
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Homework Assignment# 02

Deadline:

Problem 1:
Consider the following circuit (figure 1) having switching frequency of 100 kHz. Make necessary
assumptions when solving.

Figure 1

a) Find duty cycle.


b) Find average and peak inductor current.
c) Average source current.
d) Peak and average diode current.

Problem 2:
The input of the boost converter is 10 V and the output is 35 V. The switching frequency is 400
kHz and the load is 9 Ω. Find,

a) Duty cycle.
b) Minimum inductor value to keep the converter in continuous conduciton mode (CCM).
c) Peak value of inductor current.
Problem 3:
A buck-boost converter has following parameters,
- Input Voltage = 34 V
- Inductance = 60 uH
- Capacitance = 200 uF
- Duty Ratio = 0.75
- Switching Frequency = 10 kHz.
- Averaege Inductor Current = 29.5 A.

Determine,

a) Output voltage.
b) Minimum and maximum inductor current.
c) Value of load resistance.
Simulation assignment
This assignment aims at simulating buck-boost converter

1. Simulate a buck-boost converter with following specifications:


• Dc voltage source: 15 V
• L=0.5 mH, C=0.1 mF
• Switching frequency: 10 kHz
• D=0.4 and 0.7 for the buck and boost converters, respectively
• Load: 2 Ω

Measure the output voltage, and inductor current for each duty cycle, separately and
explain the results. What is the peak-to-peak ripple of the output voltage (and the
inductor current)?
2. Step-down (Buck) dc-dc Converter

Nominal values:
𝑉𝑑 = 8 𝑉, 𝐿 = 20 𝜇𝐻, 𝐶 = 10 𝜇𝐹, 𝑅𝑙𝑜𝑎𝑑 = 0.5 Ω, 𝑓𝑠 = 50 𝑘𝐻𝑧, 𝐷 = 0.75

Problems:
1. Obtain the 𝑣𝑜 and 𝑖𝐿 waveforms .
2. At 0.3 ms, increase the output load as a step by connecting another load of resistance 0.5
Ω. Plot 𝑣𝑜 and 𝑖𝐿 waveforms.
3. Step-up (Boost) dc-dc Converter

Nominal values:
𝑉𝑑 = 9 𝑉, 𝐿 = 10 𝜇𝐻, 𝐶 = 50 𝜇𝐹, 𝑅𝑙𝑜𝑎𝑑 = 5 Ω, 𝑓𝑠 = 50 𝑘𝐻𝑧, 𝐷 = 0.625

Problems:
1. Obtain the 𝑣𝑜 and 𝑖𝐿 waveforms .
2. At 0.3 ms, increase the output load as a step by connecting another load of resistance 0.5
Ω. Plot 𝑣𝑜 and 𝑖𝐿 waveforms.

You might also like