WEEE Report No.

HKTEC200XXXXX01 Date: XX Jan 2021 Page 1 of 12

1. General Information
Product Name : XXXX
SGS Job No. : XXXXXXX – HK
Testing Period : 21 Dec 2020 - 26 Jan 2021
Product Weight : 367.6g
Product Size : 16.5cm×8.1cm×5.7cm
: 6th category (Small IT and telecommunication equipment (no
Category under the WEEE Directive
external dimension more than 50 cm))

Reference

2. Result of Recycling/Recovery Assessment

Recycling/Recovery Recycling (%) Recovery (%)

Recycling/Recovery Targets under the
55 75
2012/19/EU WEEE Directive
Result of Assessment 79.7 89.5

WEEE requirement PASS PASS

Remark: The recycling and recovery targets in WEEE Directive are set for electrical and electronic
equipment (EEE), and are not applicable to modules or components.

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 2 of 12

3. Appearance of the Product

Front Back

Left Side Right Side

Top Bottom

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 3 of 12

4. Materials and Components to Be Selective Treated

According to Articles 8(2) and the Annex VII of the WEEE Directive, this product contains the following
components and materials to be selective treated.

Component/Material Photo No. Size & Quantity Weight (g)

C1 81.5cm2×1 61.7
Printed circuit boards of mobile phones generally,
and of other devices if the surface of the printed
C2 48.6cm2×1 30.5
circuit board is greater than 10 square
centimetres
C23 14.8cm2×1 16.8

External electric cable C27 1 19.9

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 4 of 12

5. Disassembly Tree

B1* B2* B3* B4

*: These parts could be dismantled further, more information please refer to next pages.

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 5 of 12

B1*

C1 C2 C3 C4

C5 C6 C7 C8

C9 C10 C11 C12

C13 C14 C15 C16

*: These parts could be dismantled further, more information please refer to next pages.

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 6 of 12

B1

C17 C18 C19 C20

C21 C22

B2

C23 C24 C25 C26

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 7 of 12

B3

C27 C28 C29

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 8 of 12

6. Disassembly Procedure
The disassembly procedure taken here is in accordance with the treatment requirements under the
Annex VII of the WEEE Directive. In addition, to consider economic and efficiency factors, manual
operation and disassembly tools have been applied to separate the components and materials from
this product in order to simulate the scenario at the treatment facility, and to achieve the objective that
the separated components and materials can be recycled and recovered.
6.1 Connection technique:
For this product, the connection technology including as following：
Screw :8
Adhere :4
Pressing Fits : 25
Spring :3

6.2 Disassembly tool:

The disassembly tools used for this product show as following：

Disassembly Tool Pictures Disassembly Tool Pictures

Cross screwdriver Pruning shears

6.3 Disassembly time:

3 Minutes 11 Seconds

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 9 of 12

7. Material and Recycling Information

According to the information declared by the applicant company, the material and recycling information
for this product is described in the following table.
The recycling and recovery assessment for this product is based upon economic and efficiency
considerations, and the waste treatment technologies and equipment that are most frequently available
to the market.

Energy
Percent Recycli Recove
Component / Material Weight Recove
Photo No. Weight ng ry
Composition (g) ry
(%) (%) (%)
(%)
Printed circuit board C1, C2, C3, C5, C23 115.2 31.4 28.3 - 28.3

LCD C4 12.6 3.4 3.1 - 3.1

External
electric PVC+Copper C27 19.9 5.4 1.3 3.4 4.7
cable
ABS B4 6.6 1.8 1.6 - 1.6

PC+ABS C6, C12, C24 85.5 23.3 20.5 - 20.5

PC C7, C8 49.2 13.4 11.8 - 11.8

PMMA C9, C10 19.8 5.4 4.7 - 4.7

Plastic parts
Rubber C11, C15 15.3 4.2 - 3.8 3.8

PC+GF C13 8.2 2.2 1.9 - 1.9

POM C14 0.5 0.1 0.1 - 0.1

PA66 C25 0.9 0.2 0.2 - 0.2

Metal parts Steel C16, C17, C18, C26 7.0 1.9 1.9 - 1.9

/ C19, C20, C28, C29 25.7 7.0 4.1 2.5 6.6

Mixed parts
Internal wire C21 0.7 0.2 0.1 0.1 0.2

Others FPC C22 0.5 0.1 0.1 - 0.1

Total 367.6 100.0 79.7 9.8 89.5

Note:
Due to their insignificant weight and the difficulty of their separation in a manual operation, sticker, solder,
paint and printing materials are not included in this assessment.
Plastic containing brominated flame retardants is not assessed in the list.

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 10 of 12

8. Recycling and Recovery Rate Calculation

Recycling& Recovery Rate using in the report are calculated as following formulas：

Recycling Weight
Recycling Rate = (%)
Product Total Weight

Recycling Weight + Energy Recovery Weight

Recovery Rate = (%)
Product Total Weight

Total weigh of the product is including the main product and accessories.

9. Recycling/Recovery Targets under the WEEE Directive

Minimum targets set for 6 categories EEE finished product from 15 August 2018 in directive
2012/19/EU:
Category Recycling (%) Recovery (%)
1st category (Temperature exchange equipment) 80% 85%
2nd category (Screens, monitors, and equipment containing
70% 80%
screens having a surface greater than 100 cm2)
3rd category (Lamps) 80% /
th
4 category (Large equipment
80% 85%
(any external dimension more than 50 cm))
5th category (Small equipment
55% 75%
(no external dimension more than 50 cm))
th
6 category (Small IT and telecommunication equipment
55% 75%
(no external dimension more than 50 cm))
Remark: Recycling and Recovery targets apply to EEE finished product listed in above table, and do
not apply to modules/components.

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 11 of 12

10. ANNEX VII of WEEE Directive

Selective treatment for materials and components of waste electrical and electronic equipment:
— Polychlorinated biphenyls (PCB) containing capacitors in accordance with Council Directive
96/59/EC of 16 September 1996 on the disposal of polychlorinated biphenyls and polychlorinated
terphenyls (PCB/PCT) (1).
— Mercury containing components, such as switches or backlighting lamps.
— Batteries.
— Printed circuit boards of mobile phones generally, and of other devices if the surface of the printed
circuit board is greater than 10 square centimetres.
— Toner cartridges, liquid and pasty, as well as colour toner.
— Plastic containing brominated flame retardants.
— Asbestos waste and components which contain asbestos.
— Cathode ray tubes.
— Chlorofluorocarbons (CFC), hydrochlorofluorocarbons (HCFC) or hydrofluorocarbons (HFC),
hydrocarbons (HC).
— Gas discharge lamps.
— Liquid crystal displays (together with their casing where appropriate) of a surface greater than 100
square centimeters and all those back-lighted with gas discharge lamps,
— External electric cables.
— Components containing refractory ceramic fibres as described in Commission Directive 97/69/EC of
5 December 1997 adapting to technical progress Council Directive 67/548/EEC relating to the
classification, packaging and labelling of dangerous substances .
— Components containing radioactive substances with the exception of components that are below the
exemption thresholds set in Article 3 of and Annex I to Council Directive 96/29/Euratom of 13 May
1996 laying down basic safety standards for the protection of the health of workers and the general
public against the dangers arising from ionising radiation .
— Electrolyte capacitors containing substances of concern (height > 25 mm, diameter > 25 mm or
proportionately similar volume).

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
 WEEE Report No. HKTEC200XXXXX01 Date: XX Jan 2021 Page 12 of 12

11. Recommendations for WEEE Directive Compliance

— In order to avoid the product not meeting the recycling/recovery targets regulated under the WEEE
Directive and the regulations of EU countries, the applicant company should, when selecting material
and components design, consider they can be easy to reuse and recycle. This consideration will
lessen the impact of the required international environmental directives and also improve the
product’s competitiveness.
— It is recommended that the applicant company, when designing new product, especially where
components and materials have a large weight ratio, should consider using recyclable materials in
order to increase the product’s recycling/recover ratio.
— The product should apply to the RoHS Directive (Directive 2011/65/EU on the restriction of the use of
certain hazardous substances in electrical and electronics equipment). The hazardous substance
specification in the Directive should be controlled in the homogenous material of this product.
— If a product has changed its product design, or materials or components employed, then the product
should be reassessed and retested in accordance with the WEEE Directive for recycling/recovery
assessment and RoHS for restricted/banned substances requirements.

Remark:
1. The test results were obtained from a SGS affiliated laboratory.

*** End of Report ***

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights
and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification
of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.