Government of Karnataka

Department of Technical Education

Board of Technical Examinations, Bengaluru
Course Title: ENGINEERING DRAWING-II

Credits (L:T:P) : 0:2:4 Total Contact Hours: 78 Course Code: 15CE22D

Type of Course: Tutorial Core/ Elective: Core
and Drafting Credit :03

CIE- 25 Marks SEE- 100 Marks

(***(Common to all Civil Engineering /Civil (Draughtsman/Environmental/Public Health Engineering/Water Technology

and Health Sciences Programme)***

Prerequisites: Student should know Engineering Drawing-I

Course Objectives
1. The course is aimed at developing Basic Drawing skills.
2. Develop Skills in Preparation of Engineering Drawings.
3. Develop Skills In Preparation of Engineering Drawings, their Reading and Interpretation

Course Outcomes
On successful completion of the course, the students should be able to:

Linked
Course Outcome CL
PO
Teaching Hrs
CO1 Draw Orthographic views of given Civil Engineering
R/U/Ap/Ay 1,2,3,4, 15
Objects. 5,8,9,10
CO2 Develop the ability to draw the isometric view from
the orthographic views of a given Building U/Ap/Ay 1,3,8,9 21
Components and vice versa.
CO3 Develop the perspective views for simple Civil
R/U/Ap/Ay 1,2,3,5, 12
Engineering components 8,9
CO4 Build up the concept of developing cross sections for
R/U/Ap/Ay 1,2,3,5, 09
Building components. 8,9,10
CO5 Develop Plan and Elevation for single and two room 1,2,3,4
Buildings for sustainable development as per codal R/U/Ap/Ay ,5,6,7,8, 21
provisions 9,10
Total sessions 78
Legend- R; Remember U: Understand Ap: Application Ay: Analysis C:Creation E: Evaluation

Directorate of Technical Education Karnataka State 15CE22D 1

Programme outcome Attainment Matrix

Programme Outcome
PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10

Course

ENGINEERING
DRAWING-II 3 3 3 3 3 2 2 3 3 3

Level 3- Highly Addressed, Level 2-Moderately Addressed, Level 1-Low Addressed.

Method is to relate the level of PO with the number of hours devoted to the COs which address the given PO.
If >40% of classroom sessions addressing a particular PO, it is considered that PO is addressed at Level 3
If 25 to 40% of classroom sessions addressing a particular PO, it is considered that PO is addressed at Level 2
If 5 to 25% of classroom sessions addressing a particular PO, it is considered that PO is addressed at Level 1
If < 5% of classroom sessions addressing a particular PO, it is considered that PO is considered not-addressed.
Course Contents

UNITS COURSE CONTENTS HOURS

PROJECTION OF SOLIDS
Introduction-Positioning of solids –Solid lying with base on HP- Solids
lying with base or axis inclined to HP- Solids lying with one of the lateral
1 15
faces on HP- Solids lying with one of their lateral edges on HP-Cylinder
lying with its axis or base inclined to HP- Cone lying with its axis or base
inclined to HP -Solid lying with their axis inclined to both HP and VP.
CONVERSION OF ISOMETRIC VIEWS INTO ORTHOGRAPHIC
VIEWS
2 06
Introduction –Guidelines for conversion of pictorial views into
orthographic views-Illustrative problems.
ISOMETRIC VIEWS
Principles of isometric Views
Isometric views of simple solids – cube – prisms, pyramids, cylinder and
3 15
cone . Conversion of orthographic views into isometric View
Drawing of Isometric views of combination of solids , Civil Engineering
components i.e. column footing, carpentry joints
PERSPECTIVE PROJECTIONS
Technical terms used in perspective projection- one point Perspective
4
projection and two point perspective projection for simple objects like 12
Cube, Prism, Pyramids, combination of solids and simple civil engineering
objects.
CROSS SECTION OF BUILDING COMPONENTS
Conventional Representation of Civil Engineering materials.
5 09
Cross section of Wall showing components of a Building from parapet to
foundation through door, window, wardrobe, wall, steps & columns.
BUILDING DRAWING
6 Draw Plan, Elevation and Section for Single ,Double Room Building and 21
Three Room Building form the given line Diagram and Building details.
Total 78 Hrs

Directorate of Technical Education Karnataka State 15CE22D 2

Note: Grade exercises Plan in each unit should be as per table provided below.
Course Delivery: The course will be delivered through lectures with classroom practices and Power
point presentations/ Video.
Course Assessment and Evaluation Scheme:
Metho What To When/Where Max Evidence Course
d whom (Frequency Marks collected outcomes
in the course)
CIE IA Students Graded 25 Drawing 1,2,3,4,5
Exercises Sheets
(Average of
marks allotted
to each graded
exercise)
SE End End of the 100 Answer scripts 1,2,3,4,5
E Exa course at BTE
m
Student Students Middle of the Feedback 1, 2,3 ,Delivery
Feedback course forms of course
on course
End of End of the Questionnaires 1,2,3,4,5Effecti
Course course veness of
Survey Delivery of
instructions &
Assessment
Methods
Weightage of Marks and blue print of marks for SEE

Questions to be set for SEE

Unit Major Topics A* B* C*
Cognitive Levels
R U Ap Ay C E
Projection of 15% 35% 30.00% 20.00% 0.00% 0.00%
1 15 26 18 2
solids 4 10 7 5 0 0
Conversion of 0% 20% 40.00% 40.00% 0.00% 0.00%

pictorial views
2 into 6 12 8 1
orthographic
views 0 2 5 5 0 0
Isometric 0.0% 20.0% 40.00% 40.00% 0.00% 0.00%
3 15 27 19 2
projections 0 5 11 11 0 0
Perspective 10.0% 40.0% 40.00% 20.00% 0.00% 0.00%
4 9 19 12 1
projections 2 7 7 3 0 0
Cross section of 15.00% 30.00% 30.00% 20.00% 0.00% 0.00%

5 building 9 16 12 2
components 3 5 5 3 0 0
Building 15.00% 25.00% 40.00% 20.00% 0.00% 0.00%
6 24 40 31 1
drawing 6 10 16 8 0 0
Total 78 140 100 3 5 1
Legend- R; Remember U: Understand Ap: Application Ay: Analysis C:Creation E: Evaluation

Directorate of Technical Education Karnataka State 15CE22D 3

A*-SEE QUESTIONS TO BE SET FOR (10MARKS ) in PART – A(any 2 out of 3)
B*- SEE QUESTIONS TO BE SET FOR (15MARKS) in PART – B(any 2 out of 5)
C*- SEE QUESTIONS TO BE SET FOR (35MARKS) in PART – C(Compulsory)

Questions for CIE and SEE will be designed to evaluate the various educational components
such as:
Sl. Bloom’s taxonomy % in Weightage
No
1 Remembering and Understanding 38
2 Applying the knowledge acquired from the course 31
3 Analysis 23
4 Synthesis ( Creating new knowledge) 0
5 Evaluation 0

GRADED EXERCISES

MINIMUM
UNIT TITLE OF THE
SHEETS NO OF
NO NAME OF THE UNIT DRAWING
EXERCISE

I PROJECTION OF SOLIDS 5 Projection of solids 20

CONVERSION OF ISOMETERIC 3
Isometric
II VIEWS INTO ORTHOGRAPHIC 15
projections
VIEWS
ISOMETRIC PROJECTIONS 5 Isometric
III 20
projections
IV PERSPECTIVE PROJECTIONS 4 Perspective
16
projections
CROSS SECTION OF BUILDING 3 Cross section of 15
V
building
COMPONENTS components
VI BUILDING DRAWING 6 Building drawing 10
TOTAL 26 96

TEXT BOOK

1. K.R.Gopalakrishna “Fundamentals of Drawing” Subhas Publications, 2010.

2. K.R.Gopalakrishna “Engineering Drawing” (Vol. I & II), Subhas Publications, 2014.

REFERENCES

1. R.K. Dhawan, “A text book of Engineering Drawing”, S.ChandPublishers, Delhi, 2010.

2. G.S. Phull and H.S.Sandhu, “Engineering Graphics”, Wiley Publications, 2014.
3. K.Venugopal and V.Prabhu Raja, “Engineering Graphics”, New Age International Private
Limited,2008.
4. M.B.Shah and B.C.Rana, “Engineering Drawing”, Pearson Education, 2005.
5. DhananjayA.Jolhe, “Engineering Drawing with an Introduction to AutoCAD”, Tata McGraw
Directorate of Technical Education Karnataka State 15CE22D 4
 Hill Publishing Company Limited, 2008.
6. Basant Agarwal and Agarwal.C.M., “Engineering Drawing”, Tata McGraw Hill Publishing
Company Limited, New Delhi, 2008.
7. IS 962 (1989) Code of practice for Architectural and Building Drawings

Model Question Paper

Code: 15CE22D
II semester Diploma Examination
ENGINEERING DRAWING-II

Time: 4 Hours][Max. Marks: 100

Note: Answer Any Three full questions from Part-A, Any 3full Questions from Part B&Part C is
compulsory.

Part –A(Any Two)

1. Draw the three principal views of the component as shown in the figure 1 10 marks

Fig-1

2. Draw the three principal views of the component as shown in the figure2

Fig.2

3.Show the conventional representation of Building materials in Section (IS: 962)10 marks
(a) Brick Masonary (b) Stone Masonary (c) Steel works (d)Wood

PART-B(Any Three)
Directorate of Technical Education Karnataka State 15CE22D 5
4. An equilateral triangular prism 30 mm side of base and 50mm long rests with one of its shorter
edge on HP such that rectangular face containing the edge on which the prism rests is inclined at
300 to HP. The edge on which the prism rests is inclined at 600 to VP. Draw its projections.
15marks

5. A cylinder of 40mm diameter and axis height 60mm is resting with its ends of the base diameter
on HP. The axis of the cylinder is inclined at 30° to the HP and appears to be inclined at 45° to
VP. Draw the projections of the solid in its final position.
15marks

6. Draw the isometric view of the following objects whose orthographic views are given Fig 3
15 marks

Fig-3

7. Draw the isometric view of the following objects whose orthographic views are given Fig 4

15marks

Fig-4

8. A Square based prism of 30mm side of base and height 50mm rests with its base and height 50mm
rests with its base on ground such that one of the rectangular faces is touching the picture plane.
The station point lies on the center line of the object, 60mm aboveground and 50mm in front of
the picture plane. Draw the perspective view of the square prism.
15 marks

Directorate of Technical Education Karnataka State 15CE22D 6

 PART- C(Compulsory)
9.The Line Diagram of a Two room building is shown in Fig 5.The Details and specification are as
follows. 35 Marks

(a) Level of Plinth above ground - 0.5m

(b) Height of ceiling from the floor- 3m
(c) Burnt Brick Masonry wall Thickness of wall 0.3m
(d) Doors 1.0mX 2.1m
(e) Windows 1.2mX1.2m
(f) RCC Roof 0.15m thick
(g) Parapet wall of Burnt Brick Masonry 1m height of 0.2m thick.
(h) Provide suitable Foundation of Size Stone Masonry

Draw to a scale of 1:50

(i) Plan of the Building and 15Marks
(ii) Front Elevation of the Building. 10Marks
(iii) Section along xx 10 Marks

Directorate of Technical Education Karnataka State 15CE22D 7

MODEL QUESTION BANK

Course: ENGINEERING DRAWING-I. Code: 15CE22D

UNIT-I (15 Marks)

1. A hexagonal pyramid, base 30mmside and axis 60mm long has one of its triangular face
containing the slant edge on which it rests are equally inclined to HP. The axis appears to be
inclined at 450 to VP. Draw its projections when its base is nearer to the observer than its apex.

2. Draw the projection of a pentagonal prism of base side 25mm and axis length 45mm resting on
a corner such that the two base edges passing through it make equal inclination with HP and its
base inclined at 60° to HP and the axis appears to be inclined at 30° to VP in the top view.

3. An equilateral triangular prism 30 mm side of base and 50mm long rests with one of its shorter
edge on HP such that rectangular face containing the edge on which the prism rests is inclined at
300 to HP. The edge on which the prism rests is inclined at 600 to VP. Draw its projections.

4. A cone of base diameter 50mm and altitude 70mm is lying with one of its generators on HP and
the axis appears to be inclined to VP at an angle of 400 in the top view. Draw its top and front
views.

5. A Hexagonal prism of 30 mm side of base and axis 60mm long is placed with one of its base
edges on HP such that the axis is inclined at 350 to HP and 450 to VP. Draw its projections.

6. A Pentagonal pyramid 25mm side of base and 50mm altitude rests with one of its corners on
HP such that the two base edges passing through the corner on which rests make equal
inclinations with HP. The axis is inclined at 500 to VP and 300 to HP. Draw the top and front
views of the pyramid.

7. A cone of base 60mm diameter and axis 80mm long rests on HP with its axis inclined 450 to HP
and 300 to VP. Draw the top and front views of the cone.

8. Draw the top and front views of a right cylinder of base 50mm diameter and 70mm long when it
lies on HP, such that its axis is inclined at 300 to HP and axis appears to be perpendicular to VP
in the top view.

9. An equilateral triangular prism of base side 25mm and 50mm long rests with one of the its
shorter edges on HP so that the rectangular face containing the edge on which the prism rests
inclined at 30° to the HP. The edge on which the prism rests is inclined at 60° to the VP. Draw
its projections.

10. A pentagonal prism of base edge 30mm and 60mm long has its base edge on HP. The axis of
the prism is inclined at 30° to the HP and appears to be inclined at 45° to the VP. Draw the top
view and the front views of the prism.

11. A hexagonal prism of 30mm base edge and axis 60mm long is placed with one of its base edges
on HP so that the axis is inclined at 30° to HP and the axis appears to be inclined at 45° to VP.
Draw the projections when the base of the prism is nearer to the observer.

Directorate of Technical Education Karnataka State 15CE22D 8

12. A square prism of base edge 40mm and 60mm long rests with one of its corners of the base so
that the longer edge passing through this corner is inclined at 40° to the HP. Draw the
projections if the axis appears to be inclined at 45° to the VP in the top view.

13. A square pyramid of base edge 40mm and 60mm long has one of its shorter edges on HP. The
axis of the pyramid is inclined at 30° to the HP and appears to be inclined at 45° to the VP.
Draw the projections if the apex is near to the observer.

14. A cylinder of 40mm diameter and axis height 60mm is resting with its ends of the base diameter
on HP. The axis of the cylinder is inclined at 30° to the HP and appears to be inclined at 45° to
VP. Draw the projections.

15. A cone of base diameter 50mm and axis 80mm lies on HP with its axis inclined at 45° to HP and
appears to be inclined at 30° to the VP in the top view. Draw the top and front views of the
cone.

16. A right cylinder is 50mm diameter of base and height 70mm. It rests such that the axis is
inclined at 30° and 45° to HP and VP respectively. Draw the top and front views.

17. A cone of base 80mm diameter and height 100mm is lying with one of its generators on HP and
its axis appears to be inclined at 40° to VP in the top view. Draw its front and top views.

18. Draw the projections of a pentagonal prism 20mm side of base and axis 40mm long resting on a
corner such that two base edges passing through it make equal inclinations with HP and its base
is inclined at 60° to HP, and the axis appears to be inclined at 30° to VP in the top view.

19. Draw the top and front views of a rectangular pyramid of sides of base 20x25mm and height
35mm when it lies with one of its triangular faces containing the longer edge of the base on HP.
This longer edge of the base containing the triangular face lying on HP is inclined at 60° to VP
in the top view with the apex of the pyramid nearer to VP.

20. A pentagonal pyramid 20mm side of base of 35mm altitude rests with one of its corners on HP
such that the two base edges passing through the corner on which it rests make equal
inclinations with HP. The axis is inclined at 45° to VP and 30° to HP. Draw the top and front
views of the pyramid.

21. A hexagonal pyramid, base 30mm side and axis 60mm long has one of its slant edges on HP
such that two of its triangular faces containing the slant edge on which it rests are equally
inclined to HP. The top view of the axis appears to be inclined at 45° to VP. Draw its
projections when its base is nearer to the observer than its apex.
22. A cone of base 60mm diameter and axis 80mm long rests on HP with its axis inclined 45° and
30° with HP and VP respectively. Draw the top and front views of the cone.

23. Draw the top and front views of a right cylinder of base 45mm diameter and 60mm long when it
lies on HP, such that its axis is inclined at 30° to HP and the axis appears to be perpendicular to
the VP in the top view.

Directorate of Technical Education Karnataka State 15CE22D 9

 UNIT-2(10 MARKS)
1. Draw the three principal views of the component as shown in the figure.

Fig-1

Fig-2

Fig-3

Directorate of Technical Education Karnataka State 15CE22D 10

 Fig-4

Fig-5

Fig-6

Directorate of Technical Education Karnataka State 15CE22D 11

 UNIT-3 (15 Marks)

1. Draw the isometric view of the following objects whose orthographic views are given below:

2. Draw the isometric view of the following objects whose orthographic views are given below:

3. Draw the isometric view of the following objects whose orthographic views are given below:

Directorate of Technical Education Karnataka State 15CE22D 12

.

4. Draw the isometric view of the following objects whose orthographic views are given below:

Fig-1

Directorate of Technical Education Karnataka State 15CE22D 13

 Fig-2

Fig-3

Fig-4
5. A Circular column of side 40mm and height 50mm is placed centrally on a square footing of
side 100mm and thickness 25mm. Draw the Isometric projections of the combination

6. A Cube of side 50mm is resting coaxially over a circular slab of diameter 100mm and
thickness 30mm.Draw the isometric view of the combination of the solid.
Directorate of Technical Education Karnataka State 15CE22D 14
 7. A cone having diameter of the base 60mm and height 70 mm is resting co- axially on the
square slab of side 100mm and thickness 40mm. Draw the isometric view of the combination
of the solid.

8. A cylinder of 50mm diameter and 50mm high is placed centrally on the rectangular footing
of sides 75mm and 100mm and thickness 25mm. Draw the isometric projections of the
arrangement.

9. A frustum of a cone 30mm top diameter and 60mm bottom diameter and 70mm long is
placed vertically on a square block of 80mm side and 30mm thick such that both the solids
have common axis. Draw the isometric of the combination of the solids.

10. A cylindrical slab 100mm diameter and 40mm thick is supporting a cube of 50mm edge. On
the top of the cube rests a square pyramid of altitude 55mm and side of base 30mm such that
the base edges of the pyramid are parallel to the edges of the top face. The axes of the solids
are in the same straight line. Draw the isometric projection of the combination of the solids.

11. A square pyramid of base edge 50 mm and height 80 mm rests on the top of the cube of side
100 mm. Two sides of the base of the pyramid are parallel to the top edges of the cube. Draw
the isometric view of the solid.

12. Three cubes of sides 60mm,40mm and 20mm are placed centrally one above the other. Draw
the isometric projections of the combination.

UNIT-IV (15MARKS)
1. A Square based prism of 30mm side of base and height 50mm rests with its base and height
50mm rests with its base on ground such that one of the rectangular faces is touching the
picture plane. The station point lies on the center line of the object, 60mm aboveground and
50mm in front of the picture plane. Draw the perspective view of the square prism.

2. A Cube of side 50mm side rests with its base on ground such that one of the square face is 20
mm behind the picture plane. The station point lies on the centerline of the object, 80mm
above ground and 75mm in front of the picture plane.

3. A rectangular based pyramid of sides of base 30mm and 20mm, and height 35mm rests with
its base edges in parallel to the picture plane and 30mm behind it. The station point is 50mm
in front of the picture plane, 30mmto the left of the axis of the pyramid and 50mm above the
ground. Draw the perspective view of the pyramid.

4. A model of steps has three steps of 15mm tread and rise 10mm. The steps measure 60mm
widthwise. Draw the perspective view of the model when placed with its first step 25mm
behind the picture plane and longer edge being parallel to it. The station point is 95mm from
the picture plane, 60mm above ground and lies on the center line.

5. Draw one point parallel perspective view of the block shown below. The station point is
located at 80mm to the right of the centre of the block and 100mm from the picture plane.
The observers eyelevel is 60mm above the ground level.

Directorate of Technical Education Karnataka State 15CE22D 15

 Fig-1

6. Draw the perspective view of a cube 25mm edge, resting on ground on one of its faces. It has
one of its vertical edges in the picture plane and all its vertical faces are equally inclined to
the picture plane. The station point is 55 mm in front of the picture plane. The station point is
55mm in front of the picture plane, 40mm above the ground and is in a central plane 9mm to
the left of the centre of the cube.

7. A Square prism of 30mm side of base and height 40mm rests with its base on ground such
that one of the rectangular faces is inclined at 300 to the picture plane. The nearest vertical
edge touches the picture plane. The station point is 45mm infront of the picture plane, 65mm
above ground and lies opposite to the nearest vertical edge that touches the picture plane.
Draw the perspective view.

8. A cube of 45mm side of base rests on ground such that one of the square face is inclined at
250 to the picture plane. The nearest vertical edge touches the picture plane. The station point
is 65mm in front of the picture plane, 85mm above ground and lies opposite to the nearest
vertical edge that touches the picture plane. Draw the perspective view.

9. Draw one point perspective view of the block shown below. The station point is located at
80mm to the right of the centre of the block and 100mm from the picture plane. The
observers eye level is 60mm above the ground level.

Directorate of Technical Education Karnataka State 15CE22D 16

 Fig-2

10. Draw the two point perspective view of the model shown in fig3 when its right touches
picture plane and its longer side makes an angle of 300 with it. The station point is 100 mm in
front of the picture plane and exactly opposite to the vertical edge touching the picture plane
and the point of the sight is 120mm above the ground.

UNIT-V (10 Marks)

1. Show the conventional representation of Building materials in Section (IS: 962)

2. Draw the cross section of wall from foundation to parapet for the given details.

Directorate of Technical Education Karnataka State 15CE22D 17

 UNIT-VI (35 Marks)

1. The Line Diagram of a Single room building is shown in Fig 1.The Details and specification
are as follows.
(a) Level of Plinth above ground - 0.5m
(b) Height of ceiling from the floor- 3m
(c) Burnt Brick Masonry wall Thickness of wall-0.3m
(d) Doors 1.0mX 2.1m
(e) Windows 1.2mX1.2m
(f) RCC Roof 0.15m thick
(g) Parapet wall of Burnt Brick Masonry 1m height of 0.2m thick.
(h) Provide suitable Foundation of Size Stone Masonary

All Dimensions in Metre

.
Draw to a scale of 1:50
(i) Plan of the Building and
(ii) Front Elevation of the Building.
(iii) Section along xx

2. The Line Diagram of a two room building is shown in Fig 2.The Details and specification are
as follows.

(a) Level of Plinth above ground - 0.5m

(b) Height of ceiling from the floor- 3m
(c) Burnt Brick Masonry wall Thickness of wall- 0.3m
(d) Doors 1.0mX 2.1m
(e) Windows 1.2mX1.2m
(f) RCC Roof 0.15m thick
(g) Parapet wall of Burnt Brick Masonry 1m height of 0.2m thick.
(h) Provide suitable Foundation of Size Stone Masonary

Directorate of Technical Education Karnataka State 15CE22D 18

 All Dimensions in metre.

Draw to a scale of 1:50

(i) Plan of the Building and
(ii) Front Elevation of the Building.
(iii) Section along xx

Directorate of Technical Education Karnataka State 15CE22D 19