WWW.DIESELSHIP.

COM 1

JUNE 2023
SR.NO.MEP-2306

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. Express your reactions and state the subsequent investigation you would make if a laboratory report
on a used diesel engine oil sample indicated the presence of appreciable amounts of: -
A. Iron; B. Copper, Antimony and Tin; C. Silicon.
2015/SR09 2017/SR01 2018/SR04 2020/JAN 2020/FEB/Q5 2023/JUNE/Q1

Q2. A single forged shaft for a small gear pump is broken in the middle. Suggest some emergency
repairs to the shaft to enable run the pump. State the type of repair and procedure for carrying out the
repair. What is the most viable alternative to repair if no spares are available?
2013/SR12 2015/SR01 2016/SR07 2020/OCT/Q5 2022/DEC/Q5 2023/JUNE/Q2

Q3. With reference to sea water cooled multi-tubular heat exchangers state: -
(a) The materials used for the construction of tubes, tube plate and water boxes.
(b) The various types of corrosion that the part in (a) are subjected to.
(c) Measures employed to reduce or prevent above corrosion.
2018/SR08 2023/JUNE/Q3

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q4. With reference to a cylindrical boiler which has undergone major repairs, explain: - A. How is the
boiler prepared for carrying out hydraulic test? B. What is the test pressure to which boiler is subjected
to? C. What inspection should be made before, during and after the test?
2011/SR11 2022/NOV/Q3 2023/JUNE/Q4

Q5. As a second engineer, you are required to offer for survey, to a Classification Society, a crosshead
of the engine following an unscheduled repair due to bearing failure.
A. Outline the information you would be required to provide prior to the survey
B. Briefly describe the survey procedure likely to be adopted stating with reasons the areas which should
receive close attention
C. State with reasons what information would be requested by the surveyor and /or the operation
required to be observed after re-assembly of the crosshead.
2015/SR04 2016/SR01 2023/JAN/Q8 2023/JUNE/Q5

Q6. Give a reasoned explanation why some marine diesel engines might continue to run ahead on the
astern cams following a reversal of the controls. Sketch and describe an arrangement designed to
prevent this happening.
2023/JUNE/Q6

Q7: A. As Second Engineer, outline your instructions to members of the ship’s engineering staff for
inspection of the main engine timing chain; B. The inspection in (A) has revealed that the roller chain
needs replacement. Describe how this is achieved.
2011/SR6 2011/SR12 2012/SR2 2013/SR12 2023/JUNE/Q7

Q8. Describe briefly the methods of carrying out a bend test and an impact test. Illustrate the general
form of the test pieces used and state how the final results are given for comparison of different
materials. Of what practical use are the figures obtained?
2018/DEC 2023/JAN/Q4 2023/JUNE/Q8

Q9. What is Rocking test of Deck Crane? Explain the procedure of rocking test. Tabulate and indicate
fault finding procedure. What is the action taken if deviation is out of limit?
2018/SR09 2018/SR11 2019/JAN 2019/MAR 2019/NOV 2020/JAN 2021/FEB/Q6
2021/APR/Q7 2021/DEC/Q7 2022/SEP/Q1 2023/JUNE/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

FEBRUARY 2024
SR.NO. 21224 - 1

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. With Reference to Main Engine Fuel Pumps.

(a) Explain how the setting of a variable injection timing fuel pump is checked and adjusted. (8)
(b) State why it may be necessary to adjust the settings of a variable injection timed fuel pump. (8)
2015/SR09 2017/SR01 2018/SR04 2019/MAR 2020/JAN 2020/FEB/Q3 2020/NOV/Q6
2021/FEB/Q1 2021/APR/Q2 2021/OCT/Q8 2021/DEC/Q4 2022/MAR/Q6 2022/APR/Q9 2023/OCT/Q4
2024/FEB/Q1

Q2. a) State why onboard testing of fuel oil whilst taking bunkers can be advantageous. (3)
b) State how a representative fuel sample may be obtained during the bunkering operation. (3)
c) Explain how EACH of the following is formed during the combustion of fuel: - (6)
(i) Oxides of Nitrogen, NOx (ii) Carbon Monoxide, CO (iii) Oxides of Sulphur, SOx
d) State how the effects of sulphurous products of combustion on the engine system may be reduced.
(4)
2023/MAR/Q9 2024/FEB/Q2

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q3. A. Sketch in diagrammatic form, a refrigeration unit operating on the vapour compression system.
(5)
B. Describe how it operates and how adjustments can be made to its operating temperature. (6)
C. What effect will the following have on its operation i. high ambient temperature. ii. Gradual loss of
gas. iii. Dirty heat exchanger (5)
2024/FEB/Q3

Q4. A. With the aid of a block diagram state the usual check points for maintenance of an electronic
governor fitted to an auxiliary diesel engine. (8)
B. As engine fitted with an electronic governor behaves erratically during load changes. Explain the
possible causes. (8)
2023/SEP/Q4 2024/FEB/Q4

Q5. With reference to fatigue in crankshafts explain:

a) Why, larger shafts are more susceptible to fatigue failure than their smaller Counterparts. (5)
b) With sketches how it is inhibited in practice. (5)
c) How it is identified in its initial, intermediate and final stages prior to failure. (6)
2022/AUG/Q3 2024/FEB/Q5

Q6. Enumerate the probable causes of crankcase explosions and give a general description of a system
designed to detect the presence of an explosive mixture in a crankcase? (16)
2007/SR1 2011/SR12 2014/SR06 2024/FEB/Q6

Q7. A biological sewage system develops a fault, which necessitates opening the unit for repair.
A. The risk associated with opening the unit; (6)
B. The precaution taken to reduce the risk (5)
C. Explain the significance of biological oxygen demand (B.O.D.) (5)
2012/SR8 2024/FEB/Q7

Q8. With reference to steering gear hydraulic systems:

A. Explain the factors that could contribute to failure of connecting flange leading to total loss of oil
from the system. (8)
B. Describe an arrangement designed to ensure that the problem would not cause steering failure. (8)
2009/SR8 2008/SR12 2008/SR11 2006/SR3 2010/SR9 2012/SR09 2015/SR03
2015/SR11 2018/OCT 2021/MAR/Q4 2022/DEC/Q7 2024/FEB/Q8

Q9. You have opened up a main sea-water circulating pump (centrifugal type) onboard your vessel for
examination and overhaul, describe the checks you would make, and state your conclusion regarding
any faults found. (16)
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3
2009/SR4 2008/SR7 2007/SR9 2007/SR6 2006/SR8 2006/SR7 2011/SR3
2010/SR10 2011/SR6 2005/SR9 2006/SR9 2011/SR10 2011/SR12 2013/SR7
2014/SR06 2019/DEC 2024/FEB/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

MARCH 2024
SR.NO. 20324 - 1

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. With reference to diesel engine maintenance:

a) Describe the various means that are available to check the condition of a diesel engine as a guide to
when maintenance is actually needed. (8)
b) Compare the methods described in part (a) with the use of planned maintenance schemes. (8)
2024/MAR/Q1

Q2. A. Describe how an auxiliary boiler would be blown down and opened up for inspection.
B. State the Precautions which should be taken during the inspection and when boxing up the boiler
for service.
C. Which parts require particularly close attention when opened up and describe the procedure for the
setting of safety valves.
2008/SR12 2007/SR9 2007/SR2 2006/SR8 2011/SR4 2009/SR12 2009/SR1 2011/SR12
2024/MAR/Q2

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q3. Sketch and describe a pneumatically operated control valve. Explain how the valve is operated if
the controller fails. Discuss the routine maintenance required for these valves.
2011/SR4 2007/SR3 2010/SR2 2010/SR3 2012/SR1 2012/SR2 2014/SR01
2024/MAR/Q3

Q4. A. Discuss the possible reasons for the following changes in boiler water test results, and state
what actions should be taken in each case:
1. Reduction in total dissolved solids and chemical reserves
2. Reduction in phosphate reserve, with increase in chlorides and total dissolved solids.
3. Reduction in alkalinity levels only.
B. State why the complete results of boiler tests are logged or entered into a data retrieval system
rather than a note being made of any particular result which may be outside set limits.
2009/SR8 2009/SR8 2010/SR3 2012/SR1 2012/SR2 2014/SR01 2015/SR03
2024/MAR/Q4

Q5. Sketch and describe a turbocharger bearing lubrication system. State the type of bearing employed
and explain the advantages and disadvantages of the lubricating system described.
2016/SR08 2018/OCT/Q2 2021/JUL/Q1 2022/OCT/Q8 2024/MAR/Q5

Q6. Give a reasoned opinion as to the accuracy of the following assertions:

a) Absence of oil grooves in the liner wall between the oil supply points results in increased wear of
liner and rings.
b) ‘Timed lubrication’ has little merit,
c) The most suitable position of the oil supply point is immediately below the bottom piston ring with
the piston at top dead centre.
2011/OCT/Q9 2022/OCT/Q6 2024/MAR/Q6

Q7. When ship is in dry dock, as a Second Engineer, describe inspections you would make prior to the
start of work, during the work and after completion of the work of the following:
(a) Large sea water inlet chest and valves.
(b) Forward end of ship.
(c) Propeller and stern bush.
2020/NOV/Q1 2021/OCT/Q2 2022/MAR/Q2 2024/MAR/Q7

Q8. a) With reference to a vapour compression refrigeration plant, explain why each of the following
conditions are desirable.
(i) Superheating at the compressor suction
(ii) Undercooling at the condenser outlet
(b) Describe, with the air of a pressure-enthalpy diagram, how the evaporator cooling load is affected
by the conditions stated in Q5 (a)
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3
2022/SEP/Q5 2024/MAR/Q8

Q9. Give reasons why each of the following conditions can result in oil being carried over with the water
discharge from lubricating oil centrifuges:
a) High throughput of mixture, (6)
b) Abnormally high temperature of mixture, (6)
c) Appreciable accumulation of solids in bowl. (4)
2024/MAR/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

JANUARY 2024
SR.NO. 19124 - 1

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. Under Continuous survey of machinery (CSM) bottom end bearing of a large slow speed engine is
due for survey.
A. As second engineer explain the procedure involved in complete inspection of a bottom end bearing.
B. List the precaution to be taken.
C. Indicate the reasons for possible defects which could be encountered and state how they may be
rectified.
D. What test are carried out on completion of survey and re-assembly.
2009/SR8 2007/SR3 2010/SR1 2012/SR1 2012/SR12 2013/SR1 2013/SR10
2013/SR11 2014/SR01 2014/SR11 2014/SR12 2015/SR01 2015/SR03 2015/SR06
2015/SR08 2016/SR02 2016/SR06 2014/SR03 2016/SR11 2016/SR12 2017/SR03
2017/SR04 2017/SR09 2017/SR10 2017/SR12 2018/SR01 2018/SR07 2020/NOV/Q7
2021/JAN/Q1 2021/APR/Q1 2021/JUL/Q2 2021/OCT/Q9 2021/DEC/Q2 2022/FEB/Q6 2022/NOV/Q8

Q2. With reference to Marine Diesel engines:

(a) Describe how crankshaft alignment is checked.
(b) Identify with reasons the causes of crankshaft misalignment.
(c) State how the measurements are recorded.
2020/FEB/Q7 2021/MAR/Q2 2024/JAN/Q2

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q3. With regard to the main turbine lubrication oil system:
a) (i) Describe the effects of tin oxide corrosion; (5)
(ii) Explain the actions to be taken if this occurs in a high-pressure turbine thrust bearing. (5)
b) Discuss the factors that determine the various filtration sizes: (6)
2014/SR06 2022/NOV/Q6 2023/JULY/Q1 2024/JAN/Q3

Q4. Where a waste heat boiler is subject to persistent leakage at the tube / tube plate connection, state
with reasons:
a) The possible causes of such leakage. (5)
b) The effects of this leakage. (5)
c) Methods of effecting a permanent repair. (6)
2024/JAN/Q4
Q5. A. As Second Engineer, outline your instructions to members of the ship’s engineering staff for
inspection of the main engine timing chain; (8)
B. The inspection in (A) has revealed that the roller chain needs replacement. Describe how this is
achieved. (8)
2011/SR6 2011/SR12 2012/SR2 2013/SR12 2023/JUNE/Q7 2024/JAN/Q5

Q6. a) Sketch an outboard type of oil seal suitable for oil filled stern tube indicating the principal
component. (5)
b) Explain how the seal compensated for water of the seal face maintains oil tightness. (5)
c) What is the effect of seawater contamination of stern tube oil and how contamination risk can be
reduced? (3)
d) State the physical properties required for the bearing material in oil filled stern tube. (3)
2024/JAN/Q6

Q7. a) As second engineer describe the procedure involved in the complete inspection of a cylinder liner
and piston assembly, indicating areas of significant interest. (5)
b) Explain with reasons, possible faults which might be found; (4)
c) Suggest how such faults might be avoided. (4)
d) How liner wear and wear rate is calculated? (3)
2024/JAN/Q7

Q8. With reference to main turbochargers:

a) Give a reason why binding wire is frequently fitted near the top of the blades
b) Mention one fault that occasionally develops with binding wire in services,
c) Define the cause and identification under running conditions of turbine blade damage
d) State how (c) can be largely avoided.
2023/JAN/Q5 2023/MAR/Q3 2024/JAN/Q8

Q9. What typical effects might continuous running at service speed in heavy weather have on marine
machinery? Suggest the specific attention one has to pay and the maintenance checks that have to be
carried out on the following after continued operation under heavy weather conditions:
a) intermediate shafting (3)
b) tail Shafting (3)
c) shafting coupling bolts (3)
d) engine supports (3)
e) thrust pads (4)
2024/JAN/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

JULY 2023
SR.NO.MEP-2307

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. With regard to the main turbine lubrication oil system:

a) (i) Describe the effects of tin oxide corrosion;
(ii) Explain the actions to be taken if this occurs in a high-pressure turbine thrust bearing.
b) Discuss the factors that determine the various filtration sizes:
2014/SR06 2022/NOV/Q6 2023/JULY/Q1

Q2: A. Describe the method of setting the safety valves of an exhaust gas boiler at sea.
B. State the limits in terms of %age above maximum design working pressure for setting safety valves.
C. State the formality necessary when chief engineer sets the safety valves. (16)
2011/SR6 2012/SR11 2013/SR3 2013/SR11 2023/JULY/Q2

Q3. a) Describe the Inspection and maintenance of flameproof enclosures for luminaries installed in
hazardous condition. (10)
b) List the precautions to be taken while carrying out insulation resistance test of electrical equipment
located in a hazardous area. (6)
2023/JULY/Q3

Q4: With reference to engine remote control and monitoring systems:

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
a) Explain how the location and nature of a fault may be determined if the instrument panel in the
control room is indicating a low reading for a cylinder exhaust; (6)
b) State, with reasons, THREE sources of potential problems when choosing the location for transducers
and signal transmission systems; (5)
c) In the event of complete failure of the remote control and monitoring system state how you, as 2nd
Engineer, would organize the engine room personal to ensure safe manning of the engine room and list
SIX main engine parameters, which should be manually recorded. (5)
2008/SR1 2023/JULY/Q4

Q5. Suggest a procedure to the Chief Engineer, on how you propose to ensure that the engine room
overhead crane is maintained and operated correctly. What tests certificates are required for the
overhead crane, and who is the issuing authority.
2009/SR2 2007/SR4 2006/SR5 2010/SR1 2012/SR3 2013/SR3 2013/SR6
2013/SR10 2014/SR02

Q6: With reference to electro-hydraulic steering gears:

A. Sketch and describe a steering gear with two 50% torque units conforming to the single failure
criteria.
B. State, with reasons, the precautions necessary when operating on two rams only;
C. Describe the tests necessary to ascertain that the gear will operate as required when one side of the
circuit develops a malfunction.
2008/sr9 2008/EMG 2008/sr6 2008/sr2 2007/sr3 2006/sr3
2023/JULY/Q6

Q7. a) Describe with aid of a line diagram the layout and components of a hydraulic system suitable for
the operation of deck machinery (6)
b) Explain how the hydraulic system pressure is controlled assuming the use of a variable delivery pump.
(5)
c)State which design of hydraulic motor is used in the system described in (a). (5)
2023/JULY/Q7

Q8. What is a “Cam"? Explain its function. With reference to its application in diesel engines
Discuss the requirement and the type of cam used in
a) Fuel Pump
b) Indicator drive
c) inlet Valve
d) Exhaust Valve
e) Starting air distributor. (16)
2023/JULY/Q8

Q9. Explain why auxiliary engine bottom-end bolts are prone to failure, even under normal running
conditions. Identify those features, incorporated into the design of bottom-end bolts, to inhibit failure.
Explain how this tendency is either aggravated or inhibited during maintenance and what checks are to
be carried out.
2019/AUG 2019/OCT 2020/MAR/Q4 2020/OCT/Q1 2022/SEP/Q2 2023/JULY/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

APRIL 2023
SR.NO.MEP-2304

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. A. Describe how a main engine fuel pump would be set and checked for:
(i) Timing; (ii) Quantity
B. Explain how a setting of a variable injection timing fuel pump is checked and adjusted.
C. State why it be necessary to adjust the settings of a variable injection timed fuel pump.
2023/FEB/Q1 2023/APR/Q1

Q2. What is understood by risk on board ship? As a 2nd engineer discuss various methods for hazard
identification and assessment of risk available on board.
2012/SR12 2013/SR11 2014/SR03 2015/SR02 2015/SR08 2016/SR09 2016/SR12
2017/SR10 2023/APR/Q2

Q3. A. As second engineer describe the procedure involved in the complete inspection of a cylinder
liner and piston assembly, indicating areas of significant interest.
B. Explain with reasons, possible faults which might be found;
C. Suggest how such faults might be avoided.
2012/SR7 2013/SR10 2015/SR06 2016/SR01 2016/SR11 2017/SR09 2018/SR07
2021/JUL/Q1 2022/JUL/Q1 2023/APR/Q3

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q4. (a) With the aid of a simple sketch, explain the “trouble spots” in a basic air-conditioning unit and
with reference to your sketch, explain the following: -
(a). How the problem of increase in humidity of cooled air is overcome?
(b). How discomfort caused by the excessive drying effect of heated air is overcome?
2007/SR03 2012/SR01 2012/SR02 2012/SR12 2014/SR03 2014/SR12 2015/SR08
2016/SR09 2016/SR12 2017/SR06 2017/SR07 2017/SR08 2017/SR10 2018/SR08
2018/SR09 2019/JAN 2019/FEB 2019/APR 2019/JUN 2019/JULY 2019/AUG
2019/SEP 2019/OCT 2019/NOV 2019/DEC 2020/MAR/Q3 2020/NOV/Q2 2020/DEC/Q2
2021/FEB/Q9 2021/APR/Q3 2021/APR/Q4 2021/JUL/Q1 2021/AUG/Q6 2021/SEP/Q5 2021/OCT/Q7
2021/NOV/Q6 2021/DEC/Q6 2022/JAN/Q6 2022/FEB/Q3 2022/APR/Q4 2022/JUN/Q3 2023/APR/Q4

Q5. Explain in detail how you would isolate CO2 Fixed firefighting system foe routine
maintenance. Please enumerate the Maintenance schedules and their frequency performed on this
system. Describe all tests and inspections you would make and how you would return the system to
service.
2018/SR08 2023/APR/Q5

Q6. a) Describe Three methods of tracing a superficial crack in a marine machinery component;
b) Explain how propagation of a crack in a machinery component can be arrested.

Q7: Boiler automatic combustion control has failed during operation of boiler. Explain:
A. Procedures to operate boiler in emergency
B. Action plan to investigate, rectify and bring system to normal boiler operation.
2010/SR8 2013/SR07 2023/APR/Q7

Q8: A. Outline the procedure for the inspection of the rudder in a dry dock.
B. What are the requirement with respect to steeling gear as per SOLAS 74, as amended for the
following:
i. Relief valve;
ii. Steering gear control;
iii. Electrical power circuits.
2010/SR4 2006/SR3 2010/SR3 2012/SR09 2017/SR11 2018/OCT 2021/FEB/Q2
2021/AUG/Q1 2022/APR/Q2 2023/APR/Q8

Q9. Explain how each of the following conditions contributes to the satisfactory performance of oil
centrifuges.
A. Correct bowl speed;
B. Cleanliness of bowl;
C. Low rate of feed to the bowl;
D. Contaminated oil preheated prior to centrifuging;
E. Contaminated oil allowed standing for an appreciable time prior to centrifuging.
2011/SR2 2012/SR10 2012/SR11 2013/SR4 2014/SR02 2014/SR07 2015/SR03
2016/SR01 2016/SR10 2023/APR/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

FEBRUARY 2023
SR.NO.MEP-2302

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. A. Describe how a main engine fuel pump would be set and checked for:
(i) Timing; (ii) Quantity
B. Explain how a setting of a variable injection timing fuel pump is checked and adjusted.
C. State why it be necessary to adjust the settings of a variable injection timed fuel pump.
2023/FEB/Q1

Q2. An auxiliary boiler water level control system has a differential pressure transmitter as the
detecting element for water level. A. Sketch and describe such an arrangement; B. If the transmitter
was damaged describe how a replacement unit would be calibrated
2013/SR12 2015/SR7 2018/SR08 2023/FEB/Q2

Q3. With reference to safety valves fitted to waste heat boilers:

A. State with reasons the areas which should receive particularly close examination during a survey
inspection;
B. Describe the procedure you, as Second Engineer would adopt when setting such valves at sea;
C. State the procedure to be adopted when reporting the setting of a waste heat boiler safety valve, to
a classification society.
2008/SR9 2008/EMG 2008/SR4 2007/SR1 2011/SR12 2014/SR06 2015/SR03

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
2023/FEB/Q3
Q4. With reference to timing chains:
A. Explain the causes of increasing chain slackness in service, using sketches to illustrate your answer;
B. State: each of the following: i. The effects of increased chain length:
ii. The method of assessing percentage increase in length:
C. describe how the effects of elongation are corrected:
D. State why a limit is placed on percentage chain elongation.
State what measures you, as Second Engineer, would consider necessary after the correction procedure
in Q.4(c) has been completed and the engine is running.
2023/FEB/Q4

Q5. In a situation where the main engine control system suddenly fails and it is not possible to rectify
this immediately
A. Explain the action that a 2nd engineer should take.
B. State the instruction that the 2nd engineer should issue in order to ensure the continued safe and
effective operation of the engine
2015/SR09 2017/SR01 2018/SR04 2023/FEB/Q5

Q6. With reference to main engine starting and reversing:

a) Define the function of the automatic valve and how it is controlled.
b) State what provisions are made to control the engine in the event of automatic valve
failure.
c) Define the purpose of interlocks and blocking devices, differentiating between their functions.
2023/FEB/Q6

Q7. State how each of the following practices affect piston ring life: (a) Nitriding of rings, (b) Chromium
plating of ring grooves, (c) Contouring of rubbing faces, (d) Carbon or copper coating of rubbing faces.
2022/DEC/Q3 2023/FEB/Q7

8.With reference to crossheads:

a) Describe with sketches one arrangement whereby lubricant is fed to top end bearings, slippers, and
guide.
b) Explain why the clearances of each top-end bearings are of vital importance.
c) state why booster pumps are sometimes used to feed lubricant to top end bearings.
2023/FEB/Q8

Q9. (a) Describe how it is determined whether a crankshaft was twisted during a major “smash up” in a
main engine.
(b) Explain where twisting is most likely to occur.
(c) Specify with reasons the degree of twisting that might be accommodated without correction
(d) Explain briefly what adjustments and precautions should be instituted when putting an engine with
a twisted crankshaft back into service.
2023/FEB/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

SEPTEMBER 2023
SR.NO.MEP-2309

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices
that runs on windows | iOS | mac OS | android OS| Devices such as phones,
computers, mobiles, tablets etc.
please click here to purchase our original books. we have solved all past exam
papers of last 15 years. clean content, cad drawing with our 15 years of expertise
in maritime publishing.

Q1. a) Describe how crosshead bearing and guide clearances can be checked. (6)
b) Describe, With the aid of a sketch the procedure for checking the condition of a crosshead engine
bottom end bearing (10)
2023/SEP/Q1

Q2. What are the causes of corrosion in boilers? What precautions would you take to prevent
corrosion (a) when boiler is steaming? (b) when boiler is idle? How would you test the boiler
water for acidity and alkalinity? (16)
2023/SEP/Q2

Q3. a) Describe the inspection, which is required to be carried out in the dry-dock after the stern of a
ship has heavily struck a dock wall. (8)
b) The propeller is found to be damaged, and it is decided to fit the spare propeller. Describe the
process and mention the precautions to be taken to ensure correct assembly. (8)
2023/MAR/Q8 2023/SEP/Q3

Q4. A. With the aid of a block diagram state the usual check points for maintenance of an electronic
governor fitted to an auxiliary diesel engine. (8)

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
B. As engine fitted with an electronic governor behaves erratically during load changes. Explain the
possible causes. (8)
2023/SEP/Q4

Q5. Inspection of an engine Indicates an unexpected increase in cylinder liner wear rate. State with
reasons the possible causes and remedial measures if.
(i) The problem is confined to a single cylinder (8)
(ii) The problem is common to all cylinders. (8)
2023/SEP/Q5

Q6. a) Sketch a line diagram of a high-pressure cutout of the type fitted in a refrigeration system. (8)
b) (i) Describe the operation of the high-pressure cutout sketched in (a). (8)
(ii) State TWO faults that would cause excessive high-pressure and suggest remedy for EACH
fault (8)
2023/SEP/Q6

Q7. If soon after joining a motor ship, you found a number of holding down bolts slack and fretting
occurred at slacked bolts. Describe how you as a second engineer deal such situation? (16)
2020/MAR/Q8 2023/SEP/Q6

Q8. What is Metal-locking? What types of repairs are carried out by metal-locking? Describe the repair
procedure using Metal-Locking. (16)
2019/AUG 2019/OCT 2020/MAR/Q2 2023/SEP/Q8

Q9. Sketch suitable welded joints indicating approximate plate thickness and dimensions of preparation
for the following purposes: -
a) End plate connection to shell of an unfired pressure vessel. (6)
b) Longitudinal seam of a high pressure compressed air bottle. (5)
c)Describe any faults in workmanship, which might weaken the finished products. (5)
2023/SEP/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

JANUARY 2023
SR.NO.MEP-2301

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. a. In the case of main propulsion engine explain the indications and possible effects which might
be expected from-
A. Insufficient bearing clearances; B. Excessive bearing clearances; C. Crankshaft misalignment
b. State the recommended bearing clearances for the bottom end, top end and main bearings of your
last motor vessel.
2023/JAN/Q1

Q2. Discuss the validity of EACH of the following statements with respect to large slow speed diesel
engines:
A. Bearing clearances obtained by taking leads (or use of plastic inserts) are fundamentally more
accurate than those obtained with the use of feelers;
B. Bearing wear down can be measured by taking deflections;
C. A timing chain should be renewed when its slackness causes late fuel injection and exhaust valve
operation;
D. Timing chain slackness is solely due to stretch of the link plates.
2011/SR9 2012/SR3 2013/SR7 2016/SR04 2022/DEC/Q6 2023/JAN/Q2

Q3. Your ship is due for Drydocking. Prepare repair specifications for the following:
a) Main Engine cooling sea water Overboard valve
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
b) Aft winch hydraulic oil pressure line, holed at deck penetration in Steering Compartment
c) Deck seal of a IG system used in an oil tanker
2023/JAN/Q3

Q4. Describe briefly the methods of carrying out a bend test and an impact test. Illustrate the general
form of the test pieces used and state how the final results are given for comparison of different
materials. Of what practical use are the figures obtained?
2018/DEC 2023/JAN/Q4

Q5. With reference to main turbochargers:

a) Give a reason why binding wire is frequently fitted near the top of the blades
b) Mention one fault that occasionally develops with binding wire in services,
c) Define the cause and identification under running conditions of turbine blade damage
d) State how (c) can be largely avoided.
2023/JAN/Q5

Q6.a) State the circumstances that may lead to hollow rudder becoming flooded.
b) Describe how flooding of the rudder may become evident when a vessel is on Passage.
c) Describe the procedure for:
(i) Rudder examination:
(ii) Rudder repair:
2022/AUG/Q2 2023/JAN/Q6

Q7. With reference to air receivers and bottles explain with reasons: A. Why regular systematic internal
inspection is advisable? B. Which internal areas of large receivers should receive particularly close
examination? C. How bottles are inspected internally and what parts should be closely examined? D.
How the condition of a bottle or receiver that cannot be inspected internally is checked?
2009/SR6 2008/SR12 2008/SR8 2007/SR4 2007/SR2 2011/SR4 2010/SR4
2010/SR3 2010/SR1 2001/SR7 2009/SR1 2011/SR7 2011/SR11 2012/SR4
2012/SR6 2013/SR2 2013/SR3 2013/SR09 2012/SR6 2013/SR2 2013/SR3
2013/SR09 2014/SR4 2014/SR07 2014/SR08 2014/SR10 2015/SR02 2015/SR11
2016/SR08 2017/SR02 2017/SR06 2017/SR11 2018/OCT 2023/JAN/Q7

Q8. As a second engineer, you are required to offer for survey, to a Classification Society, a crosshead
of the engine following an unscheduled repair due to bearing failure.
A. Outline the information you would be required to provide prior to the survey
B. Briefly describe the survey procedure likely to be adopted stating with reasons the areas which should
receive close attention
C. State with reasons what information would be requested by the surveyor and /or the operation
required to be observed after re-assembly of the crosshead.
2015/SR04 2016/SR01 2023/JAN/Q8

Q9. With respect to hydraulic Ram steering gears;

A. What emergency locking device can be used in order to speedily bring the steering gear to rest?
State one reason the best angular position to lock the steering gear.
B. Use a simple sketch to show where the “Jumping” (top) and wear down (bottom) rudder carrier ring
clearances can be measured. Indicate what clearances you would expect with a new steering gear;
C. State the consequences of the wear down clearances being reduced to less than Zero.
2011/SR4 2010/SR4 2010/SR3 2010/SR2 2012/SR1 2014/SR01 2014/SR03
2014/SR4 2014/SR12 2015/SR01 2015/SR08 2016/SR02 2016/SR06 2016/SR12
2017/SR07 2017/SR10 2017/SR12 2018/SR01 2020/DEC/Q7 2021/APR/Q2 2021/APR/Q8
2021/SEP/Q4 2021/NOV/Q3 2021/DEC/Q8 2022/JUN/Q7 2022/OCT/Q4 2023/JAN/Q9

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

MARCH 2023
SR.NO.MEP-2303

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. Discuss the validity of EACH of the following statements with respect to large slow speed diesel
engines:
A. Bearing clearances obtained by taking leads (or use of plastic inserts) are fundamentally more
accurate than those obtained with the use of feelers.
B. Bearing wear down can be measured by taking deflections.
C. A timing chain should be renewed when its slackness causes late fuel injection and exhaust valve
operation.
D. Timing chain slackness is solely due to stretch of the link plates.
2011/SR9 2012/SR3 2013/SR7 2016/SR04 2022/DEC/Q6 2023/JAN/Q2 2023/MAR/Q1

Q2. A. Explain in detail, how an underwater survey is carried out;

B. State the requirements to be fulfilled before an underwater survey is acceptable to the survey
authority
C. Construct a list of the items in order of importance that the underwater survey authority should
include
2006/SR1 2010/SR9 2010/SR6 2012/SR8 2013/SR8 2023/MAR/Q2

Q3. With reference to main turbochargers:

a) Give a reason why binding wire is frequently fitted near the top of the blades
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
b) Mention one fault that occasionally develops with binding wire in services,
c) Define the cause and identification under running conditions of turbine blade damage
d) State how (c) can be largely avoided.
2023/JAN/Q5 2023/MAR/Q3

Q4. Comment on the reliability and maintenance requirements of two of the following;
(i) Pneumatic control equipment, (ii) Electro-mechanical control equipment,
(iii) Electronic control equipment
(b) Discuss the routine attention required and the defects, which may occur in service.
2008/JAN 2022/NOV/Q4 2023/MAR/Q4

Q5. (a) Suggest four reasons why the temperature of the oil in the steering gear system may become
excessive.
(b) With reference to steering gears explain how the ship may be steered in each of the following
circumstances;
(i) destruction by fire of the primary supply cable;
(ii) destruction by fire of the telemotor lines;
(iii) bearing failure in the running pump;
2022/JUL/Q6 2022/MAR/Q5

Q6. A). Describe the procedure for opening a bottom end bearing for inspection making reference to
the positioning of the crank and the safety precautions to be observed.
B). State how the bearing clearance may be checked and adjusted when necessary
C). State TWO defects, which may be encountered during inspection of the bottom end bearing and
crankpin giving possible causes of EACH.
D). State TWO checks, which should be made before returning the engine to service following overhaul
of the bottom end bearing.
2015/SR11 2017/SR06 2017/SR11 2018/OCT 2021/FEB/Q7 2021/AUG/Q2 2022/JAN/Q1
2022/MAR/Q6

Q7. An Auxiliary boiler is periodically unattended and equipped with alarms to cover low water level,
high steam pressure, and air and flame failure.
A. State why and how fuel burners are automatically cut off under alarm conditions of water level, steam
pressure, air and flame failure.
B. Describe how and when each of the above alarms is tested without endangering the boiler.
2008/SR3 2011/SR7 2006-2007/EMG 2010/SR9 2011/SR22 2014/SR4 2015/SR07
2020/OCT/Q7 2022/OCT/Q7 2023/MAR/Q7

Q8. a) Describe the inspection, which is required to be carried out in the dry-dock after the stern of a
ship has heavily struck a dock wall. (8)
b) The propeller is found to be damaged, and it is decided to fit the spare propeller. Describe the
process and mention the precautions to be taken to ensure correct assembly. (8)
2023/MAR/Q8

Q9. a) State why onboard testing of fuel oil whilst taking bunkers can be advantageous. (4)
b) State how a representative fuel sample may be obtained during the bunkering operation. (4)
c) Explain how EACH of the following is formed during the combustion of fuel: - (4)
(i) Oxides of Nitrogen, NOx (ii) Carbon Monoxide, CO (iii) Oxides of Sulphur, SOx
d) State how the effects of sulphurous products of combustion on the engine system may be reduced.
2023/MAR/Q9

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

NOVEMBER 2023
SR.NO.MEP-2311

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices
that runs on windows | iOS | mac OS | android OS| Devices such as phones,
computers, mobiles, tablets etc.
please click here to purchase our original books. we have solved all past exam
papers of last 15 years. clean content, cad drawing with our 15 years of expertise
in maritime publishing.

Q1. a) Explain metal fatigue and how fatigue failure occurs. (4)
b) Differentiate between high stress/low cycle and low stress/high cycle fatigue giving
example of each. (4)
c) How do defects in the metal influence the expected life of a component. (4)
d) How does fuel injection timing and cylinder power balance influence the possibility
of fatigue cracks developing in the bedplate. (4)
2023/NOV/Q1

Q2. (a) Specify with reasons those parts requiring particularly close scrutiny during internal and external
examinations of independently fired auxiliary boilers.
(b) With reference to these examinations distinguish between metal fatigue due to caustic embrittlement,
corrosion fatigue, overheating (plastic flow) and direct overpressure. (16)
2022/SEP/Q7 2023/NOV/Q2

Q3. Describe the procedure for overhauling Main Air compressor Valves (Plate type) and explain which
parts require close attention. using sketches where necessary. Also describe the procedure for testing
of these compressor valves. (16)
2019/FEB 2019/AUG 2023/NOV/Q3

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q4. With regard to keeping the gas side of boilers in good condition discusses EACH of the following:
A. the mechanism of combustion, stating the factors which are important to good combustion; (6)
B. Oil fuel treatments; (6)
C. Soot removal equipment; (4)
2009/SR6 2008/SR7 2008/SR1 2007/EMG 2007/SR8 2006/SR7 2006/SR4
2006/SR1 2011/SR3 2010/SR10 2010/SR9 2010/SR6 2012/SR4 2012/SR8
2013/SR8 2014/SR01 2014/SR9 2014/SR12 2016/SR03 2016/SR10 2016/SR02
2016/SR06 2017/SR07 2017/SR12 2018/SR01 2018/SR03 2018/SR04 2018/SR08
2019/MAR 2020/JAN 2021/SEP/Q6 2023/NOV/Q4

Q5. Write short notes on following:

A. Magnetic Particle Inspection (MPI) (6)
B. Ultrasonic Testing (UT) (5)
C. Radiographic Testing (RT). (5)
2018/SR09 2019/MAR 2020/JAN 2020/FEB/Q6 2020/NOV/Q3 2021/SEP/Q2 2023/NOV/Q5

Q6. a) State the circumstances owing to which it may be necessary to renew a cylinder liner of a 4-
stroke auxiliary engine. (2)
b) Explain how the liner is removed. (5)
c) Explain how the new liner is fitted. (5)
d) State the important checks to be made before and after fitting. (4)
2023/NOV/Q6

Q7. With reference to the Crosshead of Large two-stroke engines:

A. Explain how crosshead and guide shoe clearances are checked, in large 2 stroke engines. (8)
B. Explain how crosshead alignment is checked and adjusted. (8)
2018/DEC 2023/NOV/Q7

Q8. With reference to fire pumps.

A. Explain how and when fire pumps should be tested, what are the requirements as per SOLAS74, as
amended. (6)
B. Describe the routine maintenance to be carried out on the various fittings on a fire line, giving
testing pressure where appropriate. (4)
C. Describe briefly how will you dismantle a fire pump for survey. Give details of factors which will
decide replacing the parts. (6)
2020/MAR/Q9 2021/NOV/Q1 2023/NOV/Q8

Q9. Severe engine vibration has recently become evident when the main engine for which you are
responsible operates within a certain speed range –
A. State, with reasons, the possible causes of such vibration; (5)
B. State the consequences of operating the engine under such vibratory conditions; (5)
C. Describe the procedure you, as Second Engineer, would implement in order to investigate and rectify
the problem. (6)
2011/SR9 2012/SR4 2013/SR1 2013/SR09 2014/SR11 2015/SR04 2015/SR06
2017/SR03 2017/SR04 2017/SR07 2017/SR09 2018/SR03 2018/SR07 2018/SR11
2019/JUN 2019/DEC 2020/FEB/Q8 2021/JAN/Q8 2021/JUL/Q9 2021/DEC/Q9 2023/AUG/Q8
2023/NOV/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

JUNE 2024
SR.NO. MEP - 2406

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. With regard to the main turbine lubrication oil system:

a) (i) Describe the effects of tin oxide corrosion. (5)
(ii) Explain the actions to be taken if this occurs in a high-pressure turbine thrust bearing. (5)
b) Discuss the factors that determine the various filtration sizes. (6)
2014/SR06 2022/NOV/Q6 2023/JULY/Q1 2024/JAN/Q3 2024/JUN/Q1

Q2. a) Comment on the reliability and maintenance requirements of the following.

(i) Pneumatic control equipment,
(ii) Electro-mechanical control equipment,
(iii) Electronic control equipment. (12)
(b) Discuss the routine attention required and the defects, which may occur in service. (4)
2008/JAN 2022/NOV/Q4 2023/MAR/Q4 2024/JUN/Q2

Q3. Discuss the advantages and disadvantages of adopting the following policies for maintenance of
main and auxiliary diesel engines.
A. Planned maintenance.
B. Condition monitoring.
C. Periodic replacement of components. (16)
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
2024/JUN/Q3

Q4. It is detected that the refrigerating compressor on board your ship has not been properly aligned
with the motor, after a major overhaul ashore, enumerate how the misalignment is detected and
remedied. (16)
2011/MAR/Q9 2024/JUN/Q4

Q5. A. Outline the procedure for the inspection of the rudder in a dry dock. (8)
B. What are the requirement with respect to steering gear as per SOLAS 74, as amended for the
following:
i. Relief valve.
ii. Steering gear control.
iii. Electrical power circuits. (8)
2010/SR4 2006/SR3 2010/SR3 2012/SR09 2017/SR11 2018/OCT 2021/FEB/Q2
2021/AUG/Q1 2022/APR/Q2 2023/APR/Q8 2024/JUN/Q5

Q6. A. Describe the events leading to a crankcase explosion.

B. State how overheating might be indicated other than by a mist detector. (4)
C. Discuss the procedure to follow in the invent of overheating being indicated. (6)
D. State how severity of a crankcase explosion is limited. (6)
2009/SR3 2008/SR11 2006/SR3 2005-6/EMG 2010/SR4 2010/SR3 2012/SR09
2015/SR04 2015/SR10 2016/SR08 2018/SR02 2021/JAN/Q6 2024/JUN/Q6

Q7. Under Continuous survey of machinery (CSM) bottom end bearing of a large 2stroke slow speed
engine is due for survey.
A. As second engineer explain the procedure involved in complete inspection of a bottom end bearing.
(8)
B. List the precaution to be taken. (2)
C. Indicate the reasons for possible defects which could be encountered and state how they may be
rectified. (3)
D. What test are carried out on completion of survey and re-assembly. (3)
2009/SR8 2007/SR3 2010/SR1 2012/SR1 2012/SR12 2013/SR1 2013/SR10
2013/SR11 2014/SR01 2014/SR11 2014/SR12 2015/SR01 2015/SR03 2015/SR06
2015/SR08 2016/SR02 2016/SR06 2014/SR03 2016/SR11 2016/SR12 2017/SR03
2017/SR04 2017/SR09 2017/SR10 2017/SR12 2018/SR01 2018/SR07 2020/NOV/Q7
2021/JAN/Q1 2021/APR/Q1 2021/JUL/Q2 2021/OCT/Q9 2021/DEC/Q2 2022/FEB/Q6 2022/NOV/Q8
2024/JAN/Q1 2024/JUN/Q7

Q8. With reference to auxiliary boiler safety valves:

a) Describe how the valves are set to lift at the desired pressure under steam. (6)
b) Describe the precautions to be taken to ensure that the valve cannot be tampered with after setting
is completed. (5)
c) Briefly discuss accumulation of pressure test. (5)
2024/JUN/Q8

Q9. A) Describe the procedure to be undertaken when, upon a routine schedule for changing fuel
injector on a main engine, it is found that the injector body is seized and cannot be removed by
conventional means. (10)
B) Briefly explain the routine tests that are carried out on main engine fuel injectors. (6)
2020/NOV/Q8 2021/APR/Q8 2024/JUN/Q9

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3
PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

DECEMBER 2024
SR.NO. MEP - 2412

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices
that runs on windows | iOS | mac OS | android OS| Devices such as phones,
computers, mobiles, tablets etc.
Please click here to purchase our original books. we have solved all past exam
papers of last 15 years. clean content, cad drawing with our 15 years of expertise
in maritime publishing.

Q1. Briefly describe the methods of carrying out a bend test and an impact test. Illustrate the general
form of the test pieces used and state how the final results are given for comparison of different
materials. Of what practical use are the figures obtained? (16)
2018/DEC 2023/JAN/Q4 2023/JUNE/Q8 2023/OCT/Q8 2024/SEP/Q9 2024/DEC/Q1

Q2. As a second engineer, you are required to offer for survey, to a Classification Society, a crosshead
of the engine following an unscheduled repair due to bearing failure.
A. Outline the information you would be required to provide prior to the survey. (6)
B. Briefly describe the survey procedure likely to be adopted stating with reasons the areas which should
receive close attention. (5)
C. State with reasons what information would be requested by the surveyor and /or the operation
required to be observed after re-assembly of the crosshead. (5)
2015/SR04 2016/SR01 2023/JAN/Q8 2023/JUNE/Q5 2024/DEC/Q2

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q3. With reference to main air turbochargers. (16)
a) Give a reason why binding wire is frequently fitted near the top of the blades.
b) Mention one fault that occasionally develops with binding wire in services.
c) Define the cause and identification under running conditions of turbine blade damage.
d) State how (c) can be largely avoided.
2023/JAN/Q5 2023/MAR/Q3 2024/JAN/Q8 2024/DEC/Q3

Q4. In a situation where the main engine control system suddenly fails, and it is not possible to rectify
this immediately
A. Explain the action that a 2nd engineer should take. (8)
B. State the instruction that the 2nd engineer should issue in order to ensure the continued safe and
effective operation of the engine. (8)
2015/SR09 2017/SR01 2018/SR04 2023/FEB/Q5 2024/DEC/Q4

Q5. a) State why onboard testing of fuel oil whilst taking bunkers can be advantageous. (4)
b) State how a representative fuel sample may be obtained during the bunkering operation. (4)
c) Explain how EACH of the following is formed during the combustion of fuel: - (4)
(i) Oxides of Nitrogen, NOx (ii) Carbon Monoxide, CO (iii) Oxides of Sulphur, SOx
d) State how the effects of sulphurous products of combustion on the engine system may be reduced.
(4)
2023/MAR/Q9 2024/FEB/Q2 2024/DEC/Q5

Q6. A. Describe the survey procedure of an oil lubricated stern bearing and shaft. (8)
B. Explain how the integrity of the outboard seal of an oil lubricated stern tube may be proved before
the dry-dock is flooded. (8)
2009/SR2 2007/EMG 2011/SR1 2010/SR11 2011/SR7 2011/SR11 2012/SR2
2012/SR3 2012/SR6 2012/SR10 2013/SR4 2014/SR4 2014/SR07 2014/SR08
2015/SR01 2015/SR03 2022/NOV-Q1 2024/APR/Q2 2024/DEC/Q6

Q7. a) Describe the Inspection and maintenance of flameproof enclosures for luminaries installed in
hazardous condition. (10)
b) List the precautions to be taken while carrying out insulation resistance test of electrical equipment
located in a hazardous area. (6)
2023/JULY/Q3 2024/SEP/Q3 2024/DEC/Q7

Q8. A Heavy Oil purifier vibrates badly when just shutting down and coming to a stop. Suggest some
reasons for this vibration problem, when you have already made an inspection of its drive mechanism
and casing and found nothing unusual. (16)
2011/SR6 2012/SR2 2012/SR10 2024/DEC/Q8

Q9. What is a “Cam"? Explain its function. With reference to its application in diesel engines
Discuss the requirement and the type of cam used in
a) Fuel Pump
b) Indicator drive
c) Inlet Valve
d) Exhaust Valve
e) Starting air distributor. (16)
2023/JULY/Q8 2024/DEC/Q9

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3
PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

NOVEMBER 2024
SR.NO. MEP - 2411

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices
that runs on windows | iOS | mac OS | android OS| Devices such as phones,
computers, mobiles, tablets etc.
Please click here to purchase our original books. we have solved all past exam
papers of last 15 years. clean content, cad drawing with our 15 years of expertise
in maritime publishing.

Q1. With regard to keeping the gas side of boilers in good condition discusses EACH of the following:
(16)
A. The mechanism of combustion, stating the factors which are important to good combustion
B. Oil fuel treatments
C. Soot removal equipment
2009/SR6 2008/SR7 2008/SR1 2007/EMG 2007/SR8 2006/SR7 2006/SR4
2006/SR1 2011/SR3 2010/SR10 2010/SR9 2010/SR6 2012/SR4 2012/SR8
2013/SR8 2014/SR01 2014/SR9 2014/SR12 2016/SR03 2016/SR10 2016/SR02
2016/SR06 2017/SR07 2017/SR12 2018/SR01 2018/SR03 2018/SR04 2018/SR08
2019/MAR 2020/JAN 2021/SEP/Q6 2023/NOV/Q4 2024/NOV/Q1

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q2. A. During the weighment of CO2 bottles required for total flooding of Engine room, it was observed
that few bottles are less than the original capacity. State the reasons for the same and checks / tests
to be made prior refilling. (8)
B. State how often the CO2 bottles are required to be weighed and pressure tested. (8)
2008/SR1 2007/SR8 2006/SR7 2007/SR10 2007/SR2 2006/SR8 05-/EMG
2010/SR2 2015/SR10 2018/SR02 2020/FEB/Q4 2021/AUG/Q5 2022/JUL/Q5 2024/NOV/Q2

Q3. A single forged shaft for a small gear pump is broken in the middle. Suggest some emergency
repairs to the shaft to enable run the pump. State the type of repair and procedure for carrying out the
repair. What is the most viable alternative to repair if no spares are available? (16)
2013/SR12 2015/SR01 2016/SR07 2020/OCT/Q5 2022/DEC/Q5 2023/JUNE/Q2 2024/NOV/Q3

Q4. a) Discuss the Merits and demerits of a condition monitoring system compared to other maintenance
regimes. (8)
b) Describe how the data is gathered, stored and evaluated on a computer-based vibration analysis
system. (8)
2022/SEP/Q8 2024/NOV/Q4

Q5. With reference to main shaft bearings that are excessively loaded or very lightly loaded state for
each condition what are the.
a) Indications of the fault
b) Effects on adjacent bearings
c) Remedial steps.
Explain why load distribution on main shaft bearings changes in service. (16)
2022/SEP/Q6 2024/NOV/Q5

Q6.a) Describe the key differences between plate-type and tube-type coolers used in marine engine
cooling systems. How do the design and operation of each type of impact their efficiency and suitability
for different applications? (6)
b) Explain the criteria for choosing between a plate-type cooler and a tube-type cooler. (5)
c) Explain the purpose and procedure of back flushing a plate-type cooler. How does this process help
maintain the efficiency of the cooler and prevent fouling? (5)
2024/NOV/Q6

Q7.a) Explain the function of the crosshead guide shoe in a main engine. How is the crosshead guide
shoe lubricated? (8)
b) Briefly discuss the maintenance carried out on guide shoe. How can improper maintenance affect the
engine’s operation and lead to potential damage. (8)
2024/NOV/Q7

Q8.a) Describe the procedure for measuring crankshaft deflection in a marine engine. Include the steps
for preparing the engine, positioning the deflection guage and recording measurements at different
crank angles. (8)
b) Explain how to interpret the deflection data to assess the condition of the crankshaft. What do
variations in deflection readings indicate about alignment, bearing wear or potential engine stresses.
(8)
2024/NOV/Q8

Q9.a) What are the indications of a tube leak in a water tube boiler on a ship? Describe the signs and
symptoms that engineers should monitor to detect tube leaks early. (8)

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3
b) Outline the procedure for plugging a leaking tube in a water tube boiler. Include the steps for isolating
the affected area, preparing the tube and plug for plugging and ensuring the repair is secure and
complaint with safety standards. (8)
2024/NOV/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

OCTOBER 2023
SR.NO.MEP-2310

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices
that runs on windows | iOS | mac OS | android OS| Devices such as phones,
computers, mobiles, tablets etc.
please click here to purchase our original books. we have solved all past exam
papers of last 15 years. clean content, cad drawing with our 15 years of expertise
in maritime publishing.

Q1. With respect to hydraulic Ram steering gears;

A. What emergency locking device can be used in order to speedily bring the steering gear to rest?
State one reason the best angular position to lock the steering gear. (4)
B. Use a simple sketch to show where the “Jumping” (top) and wear down (bottom) rudder carrier ring
clearances can be measured. Indicate what clearances you would expect with a new steering gear; (6)
C. State the consequences of the wear down clearances being reduced to less than Zero. (6)
2011/SR4 2010/SR4 2010/SR3 2010/SR2 2012/SR1 2014/SR01 2014/SR03
2014/SR4 2014/SR12 2015/SR01 2015/SR08 2016/SR02 2016/SR06 2016/SR12
2017/SR07 2017/SR10 2017/SR12 2018/SR01 2020/DEC/Q7 2021/APR/Q2 2021/APR/Q8
2021/SEP/Q4 2021/NOV/Q3 2021/DEC/Q8 2022/JUN/Q7 2022/OCT/Q4 2023/JAN/Q9 2023/OCT/Q1

Q2. While carrying out ship’s hull inspection, describe the various defects and corresponding repairs
that might be expected in shell plating, Ford end of ship, aft end of ship, openings in shell plating,
Rudder, Propeller and stern tube. (16)
2021/APR/Q9 2023/OCT/Q2

Q3. With reference to the exhaust gas boiler of your ship explain the following:
A. Composition and reasons of soot deposits. (4)
B. Various stages of soot fire leading to high temperature fire. (4)
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
C. Procedure to be followed for firefighting under different stages of soot fire. (4)
D. Actions required prior to dry running of an exhaust gas boiler. (4)
2019/OCT 2023/OCT/Q3

Q4. With Reference to Main Engine Fuel Pumps.

(a) Explain how the setting of a variable injection timing fuel pump is checked and adjusted. (10)
(b) State why it may be necessary to adjust the settings of a variable injection timed fuel pump. (6)
2015/SR09 2017/SR01 2018/SR04 2019/MAR 2020/JAN 2020/FEB/Q3 2020/NOV/Q6
2021/FEB/Q1 2021/APR/Q2 2021/OCT/Q8 2021/DEC/Q4 2022/MAR/Q6 2022/APR/Q9 2023/OCT/Q4

Q5. What is Rocking test of Deck Crane? Explain the procedure of rocking test. Tabulate and indicate
fault finding procedure. What is the action taken if deviation is out of limit? (16)
2018/SR09 2018/SR11 2019/JAN 2019/MAR 2019/NOV 2020/JAN 2021/FEB/Q6
2021/APR/Q7 2021/DEC/Q7 2022/SEP/Q1 2023/JUNE/Q9 2023/OCT/Q5

Q6. During normal engine operation, a turbocharger rapidly loses speed and the speed reduction is
accompanied by appreciable noise -
A. State with reasons the possible causes. (4)
B. Explain in detail how the engine might be safely operated if the damage caused by this incident is
such that the turbocharger cannot function. (6)
C. State with reasons the factors which may limit engine operating speed with the turbocharger out of
action. (6)
2011/SR9 2013/SR1 2013/SR7 2013/SR10 2014/SR11 2015/SR06 2016/SR07
2016/SR11 2017/SR03 2017/SR04 2017/SR09 2018/SR07 2021/JUL/Q2 2021/SEP/Q9
2022/DEC/Q9 2023/OCT/Q6

Q7. The tailshaft of your vessel is suspected to have been damaged in a recent grounding. Explain with
sketches the type of Non-Destructive tests that you would carry out with reference to the specific parts
of the shaft, to ascertain the damage. (16)
2018/DEC 2023/OCT/Q7

Q8. Describe briefly the methods of carrying out a bend test and an impact test. Illustrate the general
form of the test pieces used and state how the final results are given for comparison of different
materials. Of what practical use are the figures obtained? (16)
2018/DEC 2023/JAN/Q4 2023/JUNE/Q8 2023/OCT/Q8

Q9. Describe the procedure to be undertaken when, upon a routine schedule for changing Exhaust Valve
on a main engine, it is found that the Exhaust valve body is seized inside the cylinder head and cannot
be removed by conventional means and also the internal threads in the exhaust valve body connecting
to the exhaust bellows are damaged. (16)
2018/SR08 2023/AUG/Q1 2023/OCT/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

OCTOBER 2024
SR.NO. MEP - 2410

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices
that runs on windows | iOS | mac OS | android OS| Devices such as phones,
computers, mobiles, tablets etc.
Please click here to purchase our original books. we have solved all past exam
papers of last 15 years. clean content, cad drawing with our 15 years of expertise
in maritime publishing.

Q1. Write short notes on following: (16)

A. Magnetic Particle Inspection (MPI)
B. Ultrasonic Testing (UT)
C. Radiographic Testing (RT)
D. Liquid penetrant testing (PT)
2024/OCT/Q1

Q2. a) Explain metal fatigue and how fatigue failure occurs. (4)
b) Differentiate between high stress/low cycle and low stress/high cycle fatigue giving example of each.
(4)
c) How do defects in the metal influence the expected life of a component. (4)
d) How does fuel injection timing and cylinder power balance influence the possibility of fatigue cracks
developing in the bedplate. (4)
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
2023/NOV/Q1 2024/OCT/Q2

Q3. What is understood by risk on board ship? As a 2nd engineer discuss various methods for hazard
identification and assessment of risk available on board. (16)
2012/SR12 2013/SR11 2014/SR03 2015/SR02 2015/SR08 2016/SR09 2016/SR12
2017/SR10 2023/APR/Q2 2023/AUG/Q9 2024/OCT/Q3

Q4. a) State the circumstances owing to which it may be necessary to renew a cylinder liner. (3)
b) Explain how the liner is removed (5)
c) Explain how the new liner is fitted. State the important checks to be made before and after fitting. (5)
d) How the liner wear rate is calculated. (3)
2024/OCT/Q4

Q5. With reference to electro-hydraulic steering gears:

A. Sketch and describe a steering gear with two 50% torque units conforming to the single failure
criteria. (8)
B. State, with reasons, the precautions necessary when operating on two rams only: (4)
C. Describe the tests necessary to ascertain that the gear will operate as required when one side of the
circuit develops a malfunction. (4)
2008/sr9 2008/EMG 2008/sr6 2008/sr2 2007/sr3 2006/sr3
2023/JULY/Q6 2024/OCT/Q5

Q6. During the overhaul of medium- speed auxiliary diesel generator you find that the white metal of
one of the bottom end bearings has cracked. Explain how you would fit a spare bearing and enumerate
the various tests you would carry before putting the machine back into service. (16)
2022/JUL/Q7 2024/OCT/Q6

Q7. With reference to crossheads:

a) Describe with sketches one arrangement whereby lubricant is fed to top end bearings, slippers, and
guide. (6)
b) Explain why the clearances of each top-end bearings are of vital importance. (5)
c) state why booster pumps are sometimes used to feed lubricant to top end bearings. (5)
2023/FEB/Q8 2024/OCT/Q7

Q8. a) Briefly discuss the different types of steam traps used on board, and how do you select the
appropriate type for an oil tanker? (8)
b) What are the common maintenance tasks and frequency requirements for steam traps to ensure
optimal performance, prevent steam leakage, and reduce energy losses, and how can regular
maintenance help extend the lifespan of a steam trap. (8)
2024/OCT/Q8

Q9. a) What are the key factors that influence the choice between a gear drive and a chain drive for a
large marine engine. (6)
b) Define backlash and explain how backlash is measured and corrected in a gear drive of large marine
engine. (5)
c) Discuss the effects of increased backlash on the performance and reliability of a large marine engine.
(5)
2024/OCT/Q9

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3
PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

JULY 2024
SR.NO. MEP - 2407

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. With regard to the main turbine lubrication oil system:

a) (i) Describe the effects of tin oxide corrosion. (5)
(ii) Explain the actions to be taken if this occurs in a high-pressure turbine thrust bearing. (5)
b) Discuss the factors that determine the various filtration sizes. (6)
2014/SR06 2022/NOV/Q6 2023/JULY/Q1 2024/JAN/Q3 2024/JUN/Q1 2024/JUL/Q1

Q2. a) Comment on the reliability and maintenance requirements of the following.

(i) Pneumatic control equipment
(ii) Electro-mechanical control equipment
(iii) Electronic control equipment. (12)
(b) Discuss the routine attention required and the defects, which may occur in service. (4)
2008/JAN 2022/NOV/Q4 2023/MAR/Q4 2024/JUN/Q2 2024/JUL/Q2

Q3. Discuss the advantages and disadvantages of adopting the following policies for maintenance of
main and auxiliary diesel engines.
A. Planned maintenance.
B. Condition monitoring.
C. Periodic replacement of components. (16)
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
2024/JUN/Q3 2024/JUL/Q3
Q4. a) What are the various types of corrosion that can occur in auxiliary boilers on ships? Describe
each type, including its causes, symptoms, and potential consequences. (8)
b) Discuss the preventive measures and maintenance practices that can be implemented to mitigate
corrosion and ensure the efficiency of the auxiliary boiler. (8)
2024/JUL/Q4

Q5. a) How is the specific fuel oil consumption (SFOC) of a ship’s main engine calculated? Outline the
steps involved in the calculation, including the necessary measurements and formulae. (8)
b) Discuss the factors that can influence SFOC and how it impacts the overall efficiency and operational
costs of the vessel. (8)
2024/JUL/Q5

Q6. Briefly discuss the working principles of the Hele Shaw pumps and swash plate pumps and how are
they used in steering gear systems? (16)
2024/JUL/Q6

Q7. What is Rocking test of Deck Crane? Explain the procedure of rocking test. Tabulate and indicate
fault finding procedure. What is the action taken if deviation is out of limit? (16)
2018/SR09 2018/SR11 2019/JAN 2019/MAR 2019/NOV 2020/JAN 2021/FEB/Q6
2021/APR/Q7 2021/DEC/Q7 2022/SEP/Q1 2023/JUNE/Q9 2023/OCT/Q5 2024/JUL/Q7

Q8. a) During an inspection it is noticed that tie rods of certain main engine units have become slack,
state with reasons the possible causes of this. (6)
b) Explain how correct tension is restored and the risk of future slackness minimized. (5)
c) A tie rod has fractured and cannot be replaced immediately, State with reasons the course of action
to be adopted in order to allow the engine to be operated without further damage. (5)
2022/OCT/Q2 2023/DEC/Q6 2024/JUL/Q8

Q9. a) What is the role of a thermostatic expansion valve in a refrigeration system on a ship? Sketch
and describe its working principle. (8)
b) Discuss the importance of proper adjustment and maintenance for efficient system operation and
consequences of a malfunctioning thermostatic expansion valve on the refrigeration cycle. (8)
2024/JUL/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

AUGUST 2024
SR.NO. MEP - 2408

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. Sketch and show all parts of two-stroke engine’s Stuffing box. Describe the procedure of in place
(Without removing piston) overhauling two stroke engine’s Stuffing box. Your answer should include all
safety precautions taken and proper tools used during overhaul of Stuffing box. (16)
2021/NOV/Q4 2022/JAN/Q9 2022/FEB/Q2 2024/AUG/Q1

Q2. Explain why auxiliary engine bottom-end bolts are prone to failure, even under normal running
conditions. Identify those features, incorporated into the design of bottom-end bolts, to inhibit failure.
Explain how this tendency is either aggravated or inhibited during maintenance and what checks are to
be carried out. (16)
2019/AUG 2019/OCT 2020/MAR/Q4 2020/OCT/Q1 2022/SEP/Q2 2023/JULY/Q9 2024/AUG/Q2

Q3. (a) Describe how it is determined whether a crankshaft was twisted during a major “smash up” in a
main engine. (4)
(b) Explain where twisting is most likely to occur. (4)
(c) Specify with reasons the degree of twisting that might be accommodated without correction. (4)
(d) Explain briefly what adjustments and precautions should be instituted when putting an engine with
a twisted crankshaft back into service. (4)
2023/FEB/Q9 2024/AUG/Q3
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2

Q4. Under Continuous Survey of Machinery, the crosshead bearing of a large slow speed engine is due
for survey.
a) Explain the procedure involved in the inspection of a cross-head bearing. (6)
b) List the precaution to be taken. (4)
c) Indicate the reasons for possible defects which could be encountered and state how they may be
rectified. (3)
d) What test are carried out on completion of survey and reassembly. (3)
2024/AUG/Q4

Q5. Describe how a jerk type of fuel pump is replaced, making specific reference to initial setting and
governor connections. Explain how the actual and effective strokes are adjusted. Identify the common
faults of these pumps. State how engine performance is affected by each of these faults and why prompt
attention is necessary. (16)
2022/DEC/Q1 2024/AUG/Q5

Q6. Following a recent turbocharger (T/C) overhaul, it has been observed that the scavenge air pressure
is lower than before, and the engine power output has also been reduced.
a) State the possible causes of the problem with reasons. (5)
b) State the engine operational information that should be gathered to detect the possible causes of
the problem, along with reasons for each type of information. (5)
c) State the instructions which should be issued with respect to future T/C overhauls in order to prevent
similar incidents. (6)
2024/AUG/Q6

Q7. a) Compare the working principles and applications of the turbine used in cargo oil pumps with the
turbine in a turbocharger on board a ship. How do the design and operational requirements differ
between these two types of turbines? (8)
b) What methods are employed to vary the speed of a cargo oil turbine on board a ship, and how do
these methods ensure precise control of cargo operations? (4)
c) What is the role of a vacuum condenser in the cargo system of an oil tanker, and how does it contribute
to the efficiency and safety of cargo operations? (4)
2024/AUG/Q7

Q8. Explain the thermodynamic cycle involved in the air conditioning system on board a ship, detailing
the key components and their functions. Additionally, describe the unloading and loading mechanisms
used in the system to maintain efficiency and manage varying cooling loads. (16)
2024/AUG/Q8

Q9. a) What is the working principle of a plate type cooler on a ship, and what are its main components?
How does it differ from other types of heat exchangers used on ships? (6)
b) What materials are commonly used for the packing in plate type coolers on board ships, and how do
these materials impact the efficiency and durability of the cooler? (5)
c) Describe the process of back flushing a plate type cooler on a ship. Why is back flushing important,
and what potential issues can it prevent or mitigate. (5)
2024/AUG/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

SEPTEMBER 2024
SR.NO. MEP - 2409

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices
that runs on windows | iOS | mac OS | android OS| Devices such as phones,
computers, mobiles, tablets etc.
Please click here to purchase our original books. we have solved all past exam
papers of last 15 years. clean content, cad drawing with our 15 years of expertise
in maritime publishing.

Q1. Explain how each of the following conditions contributes to the satisfactory performance of oil
centrifuges. (16)
A. Correct bowl speed.
B. Cleanliness of bowl.
C. Low rate of feed to the bowl.
D. Contaminated oil preheated prior to centrifuging.
E. Contaminated oil allowed standing for an appreciable time prior to centrifuging.
2011/SR2 2012/SR10 2012/SR11 2013/SR4 2014/SR02 2014/SR07 2015/SR03
2016/SR01 2016/SR10 2023/APR/Q9 2024/SEP/Q1

Q2. (a) Explain how can the cooling spaces within a cylinder jacket be examined without withdrawing
the cylinder liner? (6)

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
(b) To what parts of a cylinder jacket would give attention after removing an old cylinder liner prior to
fitting a new one? (4)
(c) What periodic attention must be given to the scavenge air space and piston-rod packing (Stuffing
box) at the bottom of a cylinder liner? (6)
2021/MAR/Q3 2021/AUG/Q9 2022/MAR/Q1 2022/APR/Q1 2024/SEP/Q2

Q3. a) Describe the Inspection and maintenance of flameproof enclosures for luminaries installed in
hazardous condition. (10)
b) List the precautions to be taken while carrying out insulation resistance test of electrical equipment
located in a hazardous area. (6)
2023/JULY/Q3 2024/SEP/Q3

Q4. Describe the method of setting the safety valves of an exhaust gas boiler at sea.
a. State the limits in terms of percentage above maximum design working pressure, for setting safety
valves. (8)
b. State the formality necessary when chief engineer sets the safety valves. (8)
2011/SR6 2012/SR11 2013/SR3 2013/SR11 2023/JULY/Q2 2024/SEP/Q4

Q5. Sketch and describe the arrangement of a main engine camshaft chain. Describe the repair
procedure following fracture of one chain link during operation of the engine. Give possible reasons for
the failure and explain how the chain is set initially at the correct degree of tension. (16)
2022/NOV/Q2 2024/SEP/Q5

Q6. State how each of the following practices affect piston ring life: (a) Nitriding of rings
(b) Chromium plating of ring grooves (c) Contouring of rubbing faces (d) Carbon or copper coating of
rubbing faces. (16)
2022/DEC/Q3 2023/FEB/Q7 2024/SEP/Q6

Q7. a. In the case of main propulsion engine, explain the indications and possible effects which might
be expected from-
A. Insufficient bearing clearances. B. Excessive bearing clearances. C. Crankshaft misalignment. (10)
b. State the recommended bearing clearances for the bottom end, top end and main bearings of your
last motor vessel. (6)
2023/JAN/Q1 2024/SEP/Q7

Q8. With respect to hydraulic Ram steering gears:

A. What emergency locking device can be used in order to speedily bring the steering gear to rest?
State one reason the best angular position to lock the steering gear. (4)
B. Use a simple sketch to show where the “Jumping” (top) and wear down (bottom) rudder carrier ring
clearances can be measured. Indicate what clearances you would expect with a new steering gear. (8)
C. State the consequences of the wear down clearances being reduced to less than zero. (4)
2011/SR4 2010/SR4 2010/SR3 2010/SR2 2012/SR1 2014/SR01 2014/SR03
2014/SR4 2014/SR12 2015/SR01 2015/SR08 2016/SR02 2016/SR06 2016/SR12
2017/SR07 2017/SR10 2017/SR12 2018/SR01 2020/DEC/Q7 2021/APR/Q2 2021/APR/Q8
2021/SEP/Q4 2021/NOV/Q3 2021/DEC/Q8 2022/JUN/Q7 2022/OCT/Q4 2023/JAN/Q9 2023/OCT/Q1
2024/SEP/Q8

Q9. Describe briefly the methods of carrying out a bend test and an impact test. Illustrate the general
form of the test pieces used and state how the final results are given for comparison of different
materials. Of what practical use are the figures obtained? (16)
2018/DEC 2023/JAN/Q4 2023/JUNE/Q8 2023/OCT/Q8 2024/SEP/Q9

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3
PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

APRIL 2024
SR.NO. MEP - 2404

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2024)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. Suggest a procedure to the Chief Engineer, on how you propose to ensure that the engine room
overhead crane is maintained and operated correctly. What tests certificates are required for the
overhead crane, and who is the issuing authority. (16)
2009/SR2 2007/SR4 2006/SR5 2010/SR1 2012/SR3 2013/SR3 2013/SR6
2013/SR10 2014/SR02 2023/JULY/Q5 2024/APR/Q1

Q2. A. Describe the survey procedure of an oil lubricated stern bearing and shaft. (8)
B. Explain how the integrity of the outboard seal of an oil lubricated stern tube may be proved before
the dry-dock is flooded. (8)
2009/SR2 2007/EMG 2011/SR1 2010/SR11 2011/SR7 2011/SR11 2012/SR2
2012/SR3 2012/SR6 2012/SR10 2013/SR4 2014/SR4 2014/SR07 2014/SR08
2015/SR01 2015/SR03 2022/NOV-Q1 2024/APR/Q2

Q3. Fatigue is one of the main causes of crankshaft failure.

A. Indicate on a sketch the most likely location of a fatigue crack. (4)
B. Explain how a fatigue failure is identified. (4)
C. Describe how a fatigue crack may be initiated. (4)
D. Describe, with the aid of sketches, the methods used to inhibit fatigue cracks. (4)
2009/SR2 2007/SR4 2010/SR11 2011/SR7 2005/SR3 2011/SR11 2012/SR3

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
2012/SR12 2013/SR2 2013/SR3 2013/SR6 2013/SR09 2014/SR01 2014/SR4
2014/SR10 2015/SR01 2015/SR04 2022/NOV/Q5 2024/APR/Q3

Q4. An auxiliary engine exhibits a tendency to hunt to such an extent that the engine speed variation
prohibits the connection of the machine to the switchboard.
A. Discuss the possible causes of hunting. (8)
B. Explain how the problem of hunting can be rectified. (8)
2009/SR7 2007/SR4 2011/SR7 2005/SR3 2005/SR7 2005/EMG 2006/SR6
2011/SR11 2010/SR3 2012/SR7 2013/SR2 2013/SR3 2013/SR6 2013/SR10
2013/SR11 2014/SR02 2014/ SR4 2014/SR10 2015/SR02

Q5. For a fully automatic provisions refrigeration system incorporating a number of rooms; A. Explain
how each room temperature is set; B. Describe the sequence of events following a demand for increased
refrigerant flow from one room; C. State with reasons the devices incorporated into the system to protect
the machinery and equipment against malfunction; D. State how satisfactory operation of the plant can
be established?
2009/SR7 2007/SR4 2010/SR3 2011/SR11 2011/SR7 2012/SR7 2012/SR12
2013/SR11 2014/SR4 2014/SR10 2015/SR02 2022/DEC/Q8 2024/APR/Q5

Q6. What short notes on the following;

A. Measures to stop exhaust gas leakage in the engine room. (8)
B. Measures to stop oil leakages in the engine room. (8)
2009/SR7 2007/SR4 2010/SR4 2010/SR3 2011/SR7 2011/SR11 2012/SR6
2013/SR2 2014/SR07 2013/SR2 2014/SR07 2014/SR08 2024/APRQ6

Q7. With reference to air receivers and bottles explain with reasons:
A. Why regular systematic internal inspection is advisable? (4)
B. Which internal areas of large receivers should receive particularly close examination? (4)
C. How bottles are inspected internally and what parts should be closely examined? (4)
D. How the condition of a bottle or receiver that cannot be inspected internally is checked? (4)
2009/SR6 2008/SR12 2008/SR8 2007/SR4 2007/SR2 2011/SR4 2010/SR4
2010/SR3 2010/SR1 2001/SR7 2009/SR1 2011/SR7 2011/SR11 2012/SR4
2012/SR6 2013/SR2 2013/SR3 2013/SR09 2012/SR6 2013/SR2 2013/SR3
2013/SR09 2014/SR4 2014/SR07 2014/SR08 2014/SR10 2015/SR02 2015/SR11
2016/SR08 2017/SR02 2017/SR06 2017/SR11 2018/OCT 2023/JAN/Q7 2023/AUG/Q4
2024/APR/Q7

Q8. Describe the hull inspection that you would carry out as the senior engineer of ship in dry dock
stating what defects you may find and the repairs that may be necessary with respect to;
A. Shell plating
B. Forward end of ship
C. Aft end of ship
D. Opening in shell plating
E. Rudder; F. Propeller and stern tube (16)
2010/SR2 2008/SR4 06-07/EM 2006/SR4 2006/SR2 2010/SR1 2011/SR7
2011/SR11 2013/SR02 2015/SR7 2015/SR11 2017/SR11 2018/OCT 2020/OCT/Q6
2024/APR/Q8

Q9. With reference to Auxiliary boiler safety valves.

A. Describe with the aid of Sketch the safety valve for an auxiliary boiler. (6)
B. Identify with reasons. The parts that require particularly close attention during overhaul. (5)
C. Describe how the safety valves are reset after an overhaul. (5)
2009/SR7 2008/SR6 2007/SR5 2006/SR9 2011/SR2 2011/SR7 2011/SR11 2013/SR02

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3
2019/FEB 2019/AUG 2020/NOV/Q4 2021/FEB/Q4 2021/APR/Q5 2021/OC/Q5 2022/MAR/Q4 2022/JUN/Q8
2024/APR/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

DECEMBER 2023
SR.NO.MEP-2312

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. Express your reactions and state the subsequent investigation you would make if a laboratory report
on a used diesel engine oil sample indicated the presence of appreciable amounts of: - (16)
A. Iron; B. Copper, Antimony and Tin; C. Silicon.
2015/SR09 2017/SR01 2018/SR04 2020/JAN 2020/FEB/Q5 2023/JUNE/Q1 2023/DEC/Q1

Q2. With reference to health hazards from asbestos:

A. State where asbestos may be found on board ship; (5)
B. State the health risks from asbestos; (6)
C. Outline the precautions necessary to minimize exposure to asbestos during an emergency repair.
(5)
2019/DEC 2023/DEC/Q2

Q3. Describe the procedure for replacing a Main Engine cylinder liner and explain using sketches where
necessary, those parts, which require close attention during lifting of cylinder liner. Also describe the
procedure for pressure testing the cooling water side of the Main Engine Cylinder head. (16)
2019/JUN 2019/DEC 2023/DEC/Q3

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
Q4. a) State the reason for fitting crosshead guides to engines and explain why ‘ahead’ and ‘astern’
faces are required with uni-directional engines. (5)
b) Describe how crosshead guide clearance is checked and adjusted. (6)
c) List reasons for limiting such crosshead clearance. (5)
2022/OCT/Q9 2023/DEC/Q4

Q5. If soon after joining a motor ship, you found a number of holding down bolts slack and fretting
occurred at slacked bolts. Describe how you as a second engineer deal such situation? (16)
2020/MAR/Q8 2023/SEP/Q7 2023/DEC/Q5

Q6. a) During an inspection it is noticed that tie rods of certain main engine units have become slack,
state with reasons the possible causes of this. (6)
b) Explain how correct tension is restored and the risk of future slackness minimized. (5)
c) A tie rod has fractured and cannot be replaced immediately, State with reasons the course of action
to be adopted in order to allow the engine to be operated without further damage. (5)
2022/OCT/Q2 2023/DEC/Q6

Q7. With reference to fixed CO2 system for fighting machinery space fires:
a) sketch a CO2 bottled system. (6)
b) How the number of CO2 bottles required for ship is calculated? (4)
c) explain how the system sketched in part (a) is protected from overpressure. (3)
d) Describe the periodic maintenance required. (3)
2022/AUG/Q5 2023/DEC/Q7

Q8. a) State what is meant by machinery condition monitoring. (6)

b) Describe how typical shipboard condition monitoring is carried out. (5)
c) State how the information obtained by monitoring may be used to indicate Machinery condition
trends. (5)
2022/AUG/Q4 2023/DEC/Q8

Q9. a) Describe TWO methods of tracing a superficial crack in a marine machinery component. (8)
b) Explain how propagation of a crack in a machinery component can be arrested. (8)
2023/DEC/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

AUGUST 2023
SR.NO.MEP-2308

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II
TIME ALLOWED - 3 HOURS
Total Marks - 100
(India 2023)

Instructions :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. State answering from the backside of the front cover page.
6. Blank pages if any, to be struck by (X) at the end of each question.

Get quick access to answers via “dsguides” app. can be installed in any devices that runs on
windows | iOS | mac OS | android OS| Devices such as phones, computers, mobiles, tablets
etc.
please click here to purchase our original books. we have solved all past exam papers of last 15
years. clean content, cad drawing with our 15 years of expertise in maritime publishing.

Q1. Describe the procedure to be undertaken when, upon a routine schedule for changing Exhaust Valve
on a main engine, it is found that the Exhaust valve body is seized inside the cylinder head and cannot
be removed by conventional means and also the internal threads in the exhaust valve body connecting
to the exhaust bellows are damaged. (16)
2018/SR08 2023/AUG/Q1

Q2. It is found that the tie rods are persistently becoming slack:
A. State, with reasons, the possible causes; (6)
B. State, with reasons, the likely effects on the engine if it is allowed to operate with slack tie rods; (5)
C. Explain how this problem can be minimized? (5)
2015/SR04 2016/SR07 2023/AUG/Q2

Q3. A. Briefly explain the term fatigue and explain how fatigue failure occur; (4)
B. State the difference between high stress / low cycle and low stress / high cycle fatigue giving an
example of each; (4)
C. State how defect in metal can influence the expected safe life of a component; (4)
D. State how fuel injection timing and cylinder power balance can influence the possibility of fatigue
cracks developing in the bedplate. (4)

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
2015/SR10 2016/SR08 2017/SR02 2018/SR02 2021/JAN/Q9 2022/AUG/06 2023/AUG/Q3

Q4. With reference to air receivers and bottles explain with reasons:
A. Why regular systematic internal inspection is advisable? (4)
B. Which internal areas of large receivers should receive particularly close examination? (4)
C. How bottles are inspected internally and what parts should be closely examined? (4)
D. How the condition of a bottle or receiver that cannot be inspected internally is checked? (4)
2009/SR6 2008/SR12 2008/SR8 2007/SR4 2007/SR2 2011/SR4 2010/SR4
2010/SR3 2010/SR1 2001/SR7 2009/SR1 2011/SR7 2011/SR11 2012/SR4
2012/SR6 2013/SR2 2013/SR3 2013/SR09 2012/SR6 2013/SR2 2013/SR3
2013/SR09 2014/SR4 2014/SR07 2014/SR08 2014/SR10 2015/SR02 2015/SR11
2016/SR08 2017/SR02 2017/SR06 2017/SR11 2018/OCT 2023/JAN/Q7 2023/AUG/Q4

Q5. List the maintenance routines you plan to carry out on the deck hydraulic cranes, winches and
mooring machineries before arrival port after a long voyage, considering the fact that cargo operation
is solely dependent on the proper Functioning of the crane and winches. (16)
2019/APR 2019/JULY 2019/SEP 2019/NOV 2023/AUG/Q5

Q6. Describe, with aid of sketches, a system of turbo-charging a two-stroke cycle main engine. State
the routine attention, which should be given to the turbo-charger. (16)
2018/SR08 2018/SR11 2023/AUG/Q6

Q7. A). Describe the procedure for overhauling a boiler safety valve and explain using sketches where
necessary, those parts, which require close attention.
B). Describe the procedure for setting of boiler safety valves. (16)
2018/SR09 2019/JAN 2019/APR 2019/JULY 2019/SEP 2019/NOV 2021/APR/Q5
2023/AUG/Q7

Q8. Severe engine vibration has recently become evident when the main engine for which you are
responsible operates within a certain speed range –
A. State, with reasons, the possible causes of such vibration; (6)
B. State the consequences of operating the engine under such vibratory conditions; (5)
C. Describe the procedure you, as Second Engineer, would implement in order to investigate and rectify
the problem. (5)
2011/SR9 2012/SR4 2013/SR1 2013/SR09 2014/SR11 2015/SR04 2015/SR06
2017/SR03 2017/SR04 2017/SR07 2017/SR09 2018/SR03 2018/SR07 2018/SR11
2019/JUN 2019/DEC 2020/FEB/Q8 2021/JAN/Q8 2021/JUL/Q9 2021/DEC/Q9 2023/AUG/Q8

Q9. What is understood by risk on board ship? As a 2nd engineer discuss various methods for hazard
identification and assessment of risk available on board. (16)
2012/SR12 2013/SR11 2014/SR03 2015/SR02 2015/SR08 2016/SR09 2016/SR12
2017/SR10 2023/APR/Q2 2023/AUG/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP