1/4/24, 1:59 AM ZMCT103C - Precision Current Sensor Pinout, Features, Datasheet, Working, Application, Alternative

 (https://www.facebook.com/electronicscomponents101)  
(https://twitter.com/components101)  (https://pinterest.com/components101)
(/)

ZMCT103C - Precision Current Sensor

24 May 2021 - 0 Comments

(/sites/default/files/components/ZMCT103C- (/sites/default/files/component_pin/ZMCT103C-
Precision-Current-Sensor.jpg) Current-Sensor-Pinout.jpg)

ZMCT103C Precision Current Sensor ZMCT103C Current Sensor

Description of ZMCT103C Current Sensor Module

The microcurrent precision current sensor is a module capable to measure a current

level up to 5A. This current sensor module is based upon the ZMCT103C IC. The module
has 4 output pins and provides an analog output corresponding to the AC current
passing through the wire.

Features of ZMCT103C Current Sensor Module

ZMCT103C is a small size, high accuracy module with some features and specifications
mentioned below:
1. Current Ratio: 5 A:5 mA

https://components101.com/sensors/zmct103c-precision-current-sensor-pinout-features-datasheet-alternative 1/12
1/4/24, 1:59 AM ZMCT103C - Precision Current Sensor Pinout, Features, Datasheet, Working, Application, Alternative

2. Rated Primary Current at 50/60 Hz: 5 A


3. Winding D.C. Resistance at 20 °C: 155 Ω
4. Maximum Primary Current at 50/60 Hz: 20 A
(/)
5. Transformer Turns Ratio: Np:Ns = 1000:1
6. Isolation Voltage: 4500V
7. Onboard sampling resistor, to drop the voltage to lower levels
8. Operating Temperature: -40 to 85 °C
9. Pin Length of the secondary coil (encapsulation) > 3mm
10. Epoxy Encapsulation

Pin Configuration for ZMCT103C Current Sensor Module

The ZMCT103C module has 4 pins, which are as follows:

1. Ground (G)
2. Ground(G)
3. Signal Out
4. VCC(+5V)

Alternatives for ZMCT103C

GY712, ACS712 (https://components101.com/sensors/acs712-current-sensor-module),

ACHS 7123, WCS1700, CJMCU 219

Note: All above mentioned modules are current sensors with different current measuring
capabilities.

Note: More technical information can be found in the ZMCT103C Datasheet linked at
the bottom of this page.

Working of a Current Sensor

Current sensors operate on the principle of variation of magnetic field change between
two coils. It generates highly accurate, low noise output voltage signals which are
proportional to the applied AC current.

https://components101.com/sensors/zmct103c-precision-current-sensor-pinout-features-datasheet-alternative 2/12
1/4/24, 1:59 AM ZMCT103C - Precision Current Sensor Pinout, Features, Datasheet, Working, Application, Alternative

(/)

The module is in a donut shape which has an epoxy encapsulation, inside which a
secondary coil(Ns) is coiled around a ferrite bead. The wire whose current has to be
measured is passed through the donut hole and the wire then acts as a primary coil and
the change in the magnetic field results in the desired outputs. The measurement
accuracy of the device can be improved by increasing the number of turns in the primary
coil. This current transformer comes in use for multiple applications including HEV
inverters, Electronic power steering systems, detecting circuit overload, load drop, and
shutdown.

Connecting ZMCT103C Current Sensor Module with MCU/MPU

The ZMCT103 current sensor module can be connected to a microcontroller or a

processor easily. The module has 4 output pins, two of which are to be shorted. The
output pins are as follows; VCC, Ground, Analog Output.

https://components101.com/sensors/zmct103c-precision-current-sensor-pinout-features-datasheet-alternative 3/12
1/4/24, 1:59 AM ZMCT103C - Precision Current Sensor Pinout, Features, Datasheet, Working, Application, Alternative

(/)

There are two grounds in the current sensor module which are to be shorted and
connected to the ground of the MCU. The VCC pin is connected to the 5V of the MCU
and the OUT pin on the module is to be connected to the Analog input pin of the
MCU/MPU. Once the connections are completed, the wire whose current has to be
measured is to be passed through the donut-shaped ZMCT103C IC as shown in the
image above.

Module Configuration of a ZMCT103C Current Sensor

The ZMCT103C current sensor module consists of the donut-shaped IC which houses the
secondary windings and acts as a transformer for current measurement, as discussed
above in the ‘working section’. The module also consists of an OP07 operational amplifier
which is connected along with a sampling resistor.

https://components101.com/sensors/zmct103c-precision-current-sensor-pinout-features-datasheet-alternative 4/12
1/4/24, 1:59 AM ZMCT103C - Precision Current Sensor Pinout, Features, Datasheet, Working, Application, Alternative

(/)

This is a basic circuitry used with the sensor, generally used to amplify the signals
generated by the current transformer module.

Note: There is also a potentiometer on the ZMCT103C current sensor module which can be
used to adjust the amplification factor.

Applications of ZMCT103C Current Sensor Module

Below are some of the applications of the ZMCT103C current sensor module:
1. Measuring AC currents
2. Monitor any current surges
3. Ground fault detection
4. Household electrical equipment

2D Model of ZMCT103C

The 2D model of the current sensor module is shown in the image below. The dimension
values can be used to design custom footprints of the module and.

https://components101.com/sensors/zmct103c-precision-current-sensor-pinout-features-datasheet-alternative 5/12
1/4/24, 1:59 AM ZMCT103C - Precision Current Sensor Pinout, Features, Datasheet, Working, Application, Alternative

(/)

Note: The dimensions are in centimeters.

Component Datasheet
ZMCT103C Datasheet
(https://components101.com/sites/default/files/component_datas
Datasheet.pdf )

Tags

SENSORS (/TAGS/SENSORS) CURRENT SENSOR (/TAGS/CURRENT-SENSOR)

Related Post

https://components101.com/sensors/zmct103c-precision-current-sensor-pinout-features-datasheet-alternative 6/12