80000mfh08-01.

qxd 12/10/04 3:20 PM Page 1

Multibutton Telephone
Feature Handbook
80000mfh08-01.qxd 12/10/04 3:20 PM Page 2

Your Multibutton Display Telephone

80000 -70

CLEAR BIN 1 BIN 2 BIN 3 BIN 4 BIN 5

CHECK BIN 6 BIN 7 BIN 8 BIN 9 BIN 10

LINE 1 LINE 2 LINE 3 LINE 4 LINE 5 LINE 6

In DS1000:
LINE 7 LINE 8 LINE 9 LINE 10 LINE 11 LINE 12
Keys 7-12 are
undefined.

ABC DEF
MW ICM
For Attendants:
1 2 3
GHI JKL MNO FLASH DND
Key 11=Night Key
4 5 6 Key 12=Operator Call Key
PQRS TUV WXYZ DIAL MIC

7 8 9
OPER LND SPK

0
VOL CONF
HOLD

● The Ring/Message Lamp at the top of your telephone flashes slowly green while a call
rings your telephone, blinks green if you have new Caller ID calls, and flashes red for
new Voice Mail messages or Message Waiting.
● Your key assignments may be different than shown. Ask your Communications Manager.
● See the inside back cover of this guide for an illustration of the Super Display telephone.

Nothing contained in this manual shall be deemed to be, and this manual does not consti-
tute, a warranty of, or representation with respect to, any of the equipment covered. This
manual is subject to change without notice and NEC Unified Solutions, Inc. has no obligation
to provide any updates or corrections to this manual. Further, NEC Unified Solutions also
reserves the right, without prior notice, to make changes in equipment design or components
as it deems appropriate. No representation is made that this manual is complete or accurate
in all respects and NEC Unified Solutions shall not be liable for any errors or omissions. In
no event shall NEC Unified Solutions be liable for any incidental or consequential damages
in connection with the use of this manual. This document contains proprietary information
that is protected by copyright. All rights are reserved. No part of this document may be pho-
tocopied or reproduced without prior written consent of NEC Unified Solutions.
©2004 by NEC Unified Solutions, Inc. All Rights Reserved. Printed in U.S.A.
80000mfh08-01.qxd 12/10/04 3:20 PM Page i

Table of Contents
About Your Handsfree Options
• Handsfree lets you place and answer calls by pressing instead of
using the handset.
• With Automatic Handsfree, you can press a line key without lifting the
handset. Normally, you have Automatic Handsfree.
• Use Handsfree Answerback to answer a voice-announced Intercom call
by speaking toward your phone — without lifting the handset.

Account Codes ...............................................................1

Using Account Codes with Store and Forward . . . . . . .2
Alphanumeric Display .....................................................3
Interactive Soft Keys . . . . . . . . . . . . . . . . . . . . . . . . . .3
Alphanumeric Display Contrast Control . . . . . . . . . . . .3
Attendant Position..........................................................4
Attendant Call Queuing . . . . . . . . . . . . . . . . . . . . . . . .5
Auto Redial .....................................................................6
Background Music...........................................................8
Barge In ..........................................................................9
Call Coverage Keys........................................................10
User Programmable Feature . . . . . . . . . . . . . . . . . . . .10
Call Forwarding .............................................................11
Call Forwarding at your 22-Button or 34-Button
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Call Forwarding at your Super Display Telephone . . .15
Call Forwarding Off Premise..........................................21
Off Premise Call Forwarding at your 22-Button or 34-
Button Telephone . . . . . . . . . . . . . . . . . . . . . . . . .22
Off Premise Call Forwarding at your Super Display
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
If you have a 22-Button Non-Display Telephone . . . .30
Call Screening (with IntraMail) .......................................31
Call Screening and Group Mailboxes . . . . . . . . . . . . .31
Automatic Call Screening . . . . . . . . . . . . . . . . . . . . .32
MW LED Operation Change . . . . . . . . . . . . . . . . . . .32
Using Manual Call Screening . . . . . . . . . . . . . . . . . . .32
Using Automatic Call Screening . . . . . . . . . . . . . . . .33
Call Timer.......................................................................35
Enhanced Call Timer . . . . . . . . . . . . . . . . . . . . . . . . .35
i
80000mfh08-01.qxd 12/10/04 3:20 PM Page ii

Table of Contents
Call Waiting / Camp-On..................................................38
Callback ........................................................................39
Caller ID.........................................................................40
Single and Multiple Message Format . . . . . . . . . . . . .40
Caller ID and NVM-Series Voice Mail . . . . . . . . . . . .40
Second Call Caller ID . . . . . . . . . . . . . . . . . . . . . . . .40
Third Party Caller ID Check . . . . . . . . . . . . . . . . . . .40
Caller ID Logging ...........................................................42
Caller ID Logging at your 22-Button or 34-Button
Display Telephone . . . . . . . . . . . . . . . . . . . . . . . .42
Caller ID Logging at your Super Display Telephone .45
Central Office Calls, Answering.....................................48
User Programmable Feature . . . . . . . . . . . . . . . . . . . .48
Central Office Calls, Placing ..........................................49
Store and Forward . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Conference ...................................................................54
Dial Number Preview .....................................................55
Correcting the Displayed Digits . . . . . . . . . . . . . . . . .55
Dial Number Preview Editing Example . . . . . . . . . . .56
Direct Station Selection (DSS) .......................................57
User Programmable Feature . . . . . . . . . . . . . . . . . . . .57
Direct Station Selection Console...................................58
Default DSS Console Key Assignments . . . . . . . . . . .62
Directed Call Pickup ......................................................65
Directory Dialing............................................................66
Distinctive Ringing.........................................................68
Distinctive Ring Configuration . . . . . . . . . . . . . . . . .69
Extension Override . . . . . . . . . . . . . . . . . . . . . . . . . .74
Key Ring Override . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Do Not Disturb ..............................................................88
Do Not Disturb at your 22-Button or 34-Button
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Do Not Disturb at your Super Display Telephone . . . .89
Do Not Disturb Override ...............................................92
Door Box.......................................................................93
Extension Locking .........................................................95
Locking and Unlocking Your Extension . . . . . . . . . . .95
Entering or Changing Your PIN Number . . . . . . . . . .96

ii
80000mfh08-01.qxd 12/10/04 3:20 PM Page iii

Table of Contents
Extension Hunting.......................................................103
Flash............................................................................104
Forced Trunk Disconnect ............................................105
Group Call Pickup .......................................................106
User Programmable Feature . . . . . . . . . . . . . . . . . . .106
Group Listen ...............................................................107
Group Ring .................................................................108
Handsfree ...................................................................109
Handsfree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Handsfree Answerback . . . . . . . . . . . . . . . . . . . . . . .109
User Programmable Feature . . . . . . . . . . . . . . . . . . .110
Automatic Handsfree . . . . . . . . . . . . . . . . . . . . . . . .111
Headset Compatibility.................................................112
Headset Mode Feature Interactions . . . . . . . . . . . . . .113
User Programmable Feature . . . . . . . . . . . . . . . . . . .114
Hold ............................................................................115
Hold Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Hotline ........................................................................118
User Programmable Feature . . . . . . . . . . . . . . . . . . .118
Idle Menu Soft Keys (Super Display)...........................119
User Programmable Feature . . . . . . . . . . . . . . . . . . .119
Interactive Soft Keys ...................................................121
Intercom .....................................................................122
Handsfree Answerback . . . . . . . . . . . . . . . . . . . . . . .122
User Programmable Feature . . . . . . . . . . . . . . . . . . .123
Language Selection.....................................................124
Last Number Redial .....................................................126
Enhanced Last Number Redial . . . . . . . . . . . . . . . . .126
Enhanced Last Number Redial at your 22-Button or 34-
Button Display Telephone . . . . . . . . . . . . . . . . . .127
Enhanced Last Number Redial at your Super Display
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Meet-Me Conference ..................................................131
Message Waiting .........................................................133
Microphone Mute........................................................135
Using the Handsfree Reply Soft Key at your 22-Button
or 34-Button Display Telephone . . . . . . . . . . . . .135
Using the Handsfree Reply Soft Key at your Super
Display Telephone . . . . . . . . . . . . . . . . . . . . . . .136

iii
80000mfh08-01.qxd 12/10/04 3:20 PM Page iv

Monitor / Silent Monitor ..............................................138

Name Programming.....................................................139
Night Service / Night Ring ...........................................141
Off-Hook Signaling .....................................................142
User Programmable Feature . . . . . . . . . . . . . . . . . . .142
Paging .........................................................................143
Internal Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
External Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
User Programmable Feature . . . . . . . . . . . . . . . . . . .144
Park .............................................................................145
System Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Personal Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
Park Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Prime Line Preference .................................................149
Prime Line and Ringing Line Preference . . . . . . . . .149
User Programmable Feature . . . . . . . . . . . . . . . . . . .149
Privacy and Privacy Release Groups ...........................150
Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
Privacy Release Groups . . . . . . . . . . . . . . . . . . . . . .150
Programmable Function Keys......................................151
Check Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
User Programmable Feature . . . . . . . . . . . . . . . . . . .156
Removing Lines and Extensions ..................................157
Reverse Voice Over.....................................................158
Ringing Line Preference ..............................................160
Prime Line and Ringing Line Preference . . . . . . . . .160
User Programmable Feature . . . . . . . . . . . . . . . . . . .161
Save Number Dialed....................................................162
Selectable Display Messaging .....................................163
Selectable Display Messaging at your 22-Button or 34-
Button Display Telephone . . . . . . . . . . . . . . . . . .164
Selectable Display Messaging at your Super Display
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
Entering Additional Characters . . . . . . . . . . . . . . . . .168
Speed Dial...................................................................170
System Speed Dial . . . . . . . . . . . . . . . . . . . . . . . . . .170
Personal Speed Dial . . . . . . . . . . . . . . . . . . . . . . . . .173
Entering Speed Dial Names . . . . . . . . . . . . . . . . . . .176
User Programmable Feature . . . . . . . . . . . . . . . . . . .176

iv
80000mfh08-01.qxd 12/10/04 3:54 PM Page v

Split.............................................................................177
Tandem Trunking.........................................................179
Time and Date.............................................................180
User Programmable Feature . . . . . . . . . . . . . . . . . . .180
Transfer .......................................................................181
Transfer Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
Trunk (Line) Queuing and Callback .............................184
Line Queuing Priority . . . . . . . . . . . . . . . . . . . . . . .184
User Programmable Features ......................................186
Voice Mail....................................................................188
Calling Your Mailbox . . . . . . . . . . . . . . . . . . . . . . . .190
Leaving a Message . . . . . . . . . . . . . . . . . . . . . . . . . .191
Forwarding Calls to your Mailbox . . . . . . . . . . . . . .191
Transferring Calls to a Mailbox . . . . . . . . . . . . . . . .192
Conversation Record . . . . . . . . . . . . . . . . . . . . . . . .193
Personal Answering Machine Emulation . . . . . . . . .193
Checking Your Messages . . . . . . . . . . . . . . . . . . . . .198
Message Center Mailbox . . . . . . . . . . . . . . . . . . . . .198
Voice Over ..................................................................200
Volume and Contrast Control......................................201
Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . .201
Contrast Control . . . . . . . . . . . . . . . . . . . . . . . . . . . .203
Walking Class of Service..............................................204

v
80000mfh08-01.qxd 12/10/04 3:20 PM Page vi

vi
80000mfh08-01.qxd 12/10/04 3:20 PM Page 1

Account Codes

Your system may use

Account Codes are codes that you
Account Codes to dial to categorize and/or restrict
categorize or restrict outside calls. You can dial an
Account Code while placing a
outside calls. call or while on a call. There are
three types of Account Codes:
● Optional (Unforced) Account Codes
Optional Account Codes allow you to enter an Account Code
while placing an outside call or anytime while on a call.
These are optional codes – you don’t have to enter them.
● Forced Account Codes
Forced Account Codes require you to enter an Account Code
every time you place an outside call. If you don’t enter a code,
you can’t place the call. Your system may have Forced
Account Codes optionally enabled only for long distance calls.
● Verified Account Codes
With Verified Account Codes, the system compares the
Account Code you dial with the codes programmed into the
system. If the code matches, your call goes through. Verified
Account Codes apply only to Forced Account Codes.

To enter an Optional (Unforced) Account Code

1. Place or answer an outside call.

2. Dial , press ACCT / ACCT CODE , or press your

Account Code Programmable Function Key.
Your Communications Manager can tell which
options are available to you.
3. Enter your Account Code (up to 10 digits, using 0-9).

4. Dial , press ACCT / ACCT CODE , or press your

Account Code Programmable Function Key.

1
80000mfh08-01.qxd 12/10/04 3:20 PM Page 2

Account Codes
4. (Outgoing call only) Dial your outside number.

To enter a Forced Account Code:

1. Access a line for an outside call (any method you prefer).
You hear three beeps indicating that you must
enter an Account Code.
2. Enter your Account Code (up to 10 digits, using 0-9).
If your system uses Verified Account Codes, you
must enter a code that is stored in your system.

3. Dial , press ACCT / ACCT CODE , or press your

Account Code Programmable Function Key.
Your Communications Manager can tell which
options are available to you.
4. Dial your outside number.

Using Account Codes with Store and Forward

To place an outside call when both Store and Forward and
Forced Account Codes are enabled:
If Forced Account Codes are enabled only for long
distance calls and you are placing a local call, do not
enter an Account Code. Just dial the call normally.

1. Press + Dial (or optionally 90-98).

OR
Press Switched Loop key + Dial line group number (0-8).
OR
Press Fixed Loop key.
2. Dial number + Wait for 3 beeps + Enter Account Code.

3. Wait 6 seconds, dial , or press ACCT / ACCT CODE .

2
80000mfh08-01.qxd 12/10/04 3:20 PM Page 3

Alphanumeric Display

Display messages help

If you have a 22-Button or
you process calls, identify 34-Button Display telephone, it
callers and customize provides a two-line, 20-character
per line alphanumeric display.
features. The first line displays the date
and time (while idle) and feature
status messages. The second line displays the Interactive Soft
Key definitions.

If you have a 34-Button Super Display telephone, it provides an

eight-line, 20-character per line alphanumeric display. The first
line displays the date and time (while idle) and feature status mes-
sages, just like the 22-Button and 34-Button Display models. Lines
2-8 display the comprehensive Interactive Soft Key definitions.

Interactive Soft Keys

Interactive Soft Keys provide intuitive feature access. You’ll no
longer have to remember feature codes to access your telephone’s
most advanced features — because the function of the soft keys
changes as you process your calls. For example, while you’re on
an outside call, just press PARK to park your call in an orbit.
Basic Soft Key instruction is included in this guide. Refer to the
Soft Key Glossary (P/N 80000GLO**) for more on your
Interactive Soft Keys.

Alphanumeric Display Contrast Control

When your telephone is idle (except on 34-Button Super Display),
you can control the contrast of your telephone display.
To adjust your display contrast:

1. Press or .
If the contrast adjustment doesn’t work, your
phone may be in the Music on Hold mode. Press
HOLD and try again.

3
80000mfh08-01.qxd 12/10/04 3:20 PM Page 4

Attendant Position

The attendant is the

If you are an attendant (also called
system’s call processing an operator), you are the system’s
focal point. call processing focal point. In
addition to all the features of the
standard keyset, your attendant
extension also has the following unique features. Initially, only
your attendant extension has these capabilities. Refer to the indi-
vidual feature for the specifics.

● Barge In
You can break into a co-worker’s established call.
● Direct Trunk Access
You can dial a code to access an individual outside line.
● Forced Trunk Disconnect
In an emergency, you can release (disconnect) another user’s
active outside call.
● Night Service / Night Ring
If your telephone has a programmed Night Key, you can
press it to put the system in the Night Mode.
● Removing Trunks (Lines) and Extensions from Service
Remove problem outside lines from service — then return
them to service once the problem is corrected.
● Trunk (Line) Queuing
You can wait in line for a busy trunk (line) to become free.
To call an attendant extension:

1. Press .

2. Dial .
If your system has more than one operator, you
may have to dial 01-04 instead. You can also dial
the attendant’s extension number (e.g., 300).

4
80000mfh08-01.qxd 12/10/04 3:20 PM Page 5

Attendant Position
Attendant Call Queuing
Attendant Call Queuing helps minimize congestion if your atten-
dant extension is the overflow destination for unanswered calls.

As an attendant, your extension is never busy to your co-workers.

Instead, an unlimited number of Intercom calls can queue (i.e., wait
in line) for you to become free. These calls wait on your Operator
Call Key, which is the last Programmable Function Key on your
telephone. This key is off when you’re available and winks on (red)
when co-workers are trying to get through.
To answer a call on your Operator Call Key:
Your Operator Call Key winks on (red) when a
call is waiting.
1. Press your Operator Call Key.
Normally, this places your active outside call on
Hold and answers the waiting call.

5
80000mfh08-01.qxd 12/10/04 3:20 PM Page 6

Auto Redial

Redial a busy outside

Auto Redial periodically redials a
number automatically. busy outside number. If you place
an outside call and the call recipi-
ent is busy, you can press a soft key to enable Auto Redial. You
don’t have to retry the number, hoping it will go through.

Auto Redial will periodically retry the number up to 15 times.

Auto Redial cancels when the called party rings or answers, or
when you:
● Place or answer another outside call.
● Receive an Intercom voice announcement or answer an
Intercom call by lifting the handset or pressing SPK.
● Press SPK to cancel Auto Redial.
● Press any other fixed feature key except MIC.
● Lift and replace the handset.
● Press the CANCEL soft key (Super Display only).

To enable Auto Redial:

1. Place an outside call and receive busy tone + Press
AUTO REDIAL or ALND .
OR
2. Press a line key + Press AUTO REDIAL or ALND .
The system enables Auto Redial for the last out-
side call you dialed.
3. At a 22-Button or 34-Button Display, you see:

6
80000mfh08-01.qxd 12/10/04 3:20 PM Page 7

Auto Redial
At a Super Display, you see:

The display shows the interval between callout

attempts (e.g., 30 seconds), as well as how many
times redial has occurred (e.g., 1 of 15).
Your SPK key winks on to indicate your phone is
in the Auto Redial mode.
4. The system periodically redials the call, up to 15 times,
or until you:
– Place or answer another outside call.
– Receive an Intercom voice announcement or answer an
Intercom call by lifting the handset or pressing SPK.
– Press SPK to cancel Auto Redial.
– Press any other fixed feature key except MIC.
– Lift and replace the handset.
– Press the CANCEL soft key (Super Display only).

Note: If a Caller ID call rings while Auto Redial is enabled, your

display will show the number and optional name of the incoming
caller. However, the ringing does not cancel Auto Redial. In addi-
tion, the Auto Redial display will be restored after the Caller ID
call stops ringing.

7
80000mfh08-01.qxd 12/10/04 3:20 PM Page 8

Background Music

Have your telephone

Background Music (BGM) sends
broadcast music through music to the speaker in your tele-
the speaker for a more phone while it is idle. BGM
requires that your company have
pleasing work environment. a music source (such as a CD
player or radio) connected to
your system. Background Music automatically turns off when
your phone rings or you receive a paging announcement.

To turn Background Music on and off:

1. Do not lift the handset or press .

2. Press .

Please take note of the following:

In accordance with U.S. copyright law, a license may be required

from the American Society of Composers, Authors and Publishers
(ASCAP) or other similar organizations, if radio, television broad-
casts or music other than material not in the public domain are
transmitted through the Background Music feature of telecommu-
nications systems. The manufacturer hereby disclaims any liabili-
ty arising out of the failure to obtain such a license.

8
80000mfh08-01.qxd 12/10/04 3:20 PM Page 9

Barge In
In an emergency, use
Barge In permits you to break
Barge In to get through to
into another extension user’s
a co-worker right away. established call. This sets up a
three-way conversation between
you and the other two parties on the initial call. You can Barge In
on an Intercom call and on an outside call.

!! CAUTION !!
Unauthorized intrusion on calls using this feature may be inter-
preted as an invasion of privacy.

To Barge In on a call:
1. Call busy extension.
OR
Place call on busy line.

2. Dial or press BARG .

You hear two beeps.
3. Join the conversation in progress.

9
80000mfh08-01.qxd 12/10/04 3:20 PM Page 10

Call Coverage Keys

Cover a co-worker’s calls You can have Call Coverage Keys

from your own telephone. for co-worker’s telephones, Ring
Groups, and Extension Hunting
UCD Groups.

Your Call Coverage Key can ring immediately when a call rings
your co-worker or group, ring after a delay or just flash. In addi-
tion, the Call Coverage Key lights while your co-worker is busy,
flashes fast while your co-worker is in Do Not Disturb, and flashes
slowly while your co-worker is ringing.

Call Coverage Key Flash Rates

When the key is: The covered extension is:
Off Idle or not installed
On Busy
Flashing Slowly Ringing
Flashing Fast In Do Not Disturb for Intercom
calls (option 2) or all calls (option 3)
Wink Off In Do Not Disturb for
outside calls (option 1)

To answer a call ringing or flashing a Call Coverage Key:

1. Press flashing Call Coverage Key.

To use your Call Coverage Key to place a call to your idle

co-worker:
1. Press Call Coverage Key.

User Programmable Feature

#RAC
Assign the ringing mode for your Call Coverage keys.
See User Programmable Features at the end of this guide
for more.

10
80000mfh08-01.qxd 12/10/04 3:20 PM Page 11

Call Forwarding

Make sure your calls are

Use Call Forwarding to redirect
covered while you are your calls to another extension or
away from your desk. Voice Mail. In addition, you can set
up Call Forwarding to reroute all
calls or just outside calls.
There are four types of Call Forwarding:
● Call Forwarding When Not Answered
Calls ringing your phone forward when you don’t answer.
● Call Forwarding When Busy or Not Answered
Calls ringing your phone forward when you don’t answer or
while you are busy on another call.
● Call Forwarding Immediate
Calls to your phone forward immediately.
● Call Forwarding Off Premise
Calls to your phone forward to an off-site location (such as a
cell phone or remote office). See page 21 for more.

Call Forwarding at your 22-Button or 34-Button

Telephone
To activate Call Forwarding:

1. Press and dial , or press your Call

Forwarding key.
OR
1. Press PGM + CFWD . You see:

11
80000mfh08-01.qxd 12/10/04 3:20 PM Page 12

Call Forwarding

2. Dial or press IMM for Call Forwarding

Immediate. You see:

OR

Dial or press RNA for Call Forwarding No

Answer. You see:

OR

Dial or press BNA for Call Forwarding

Busy/No Answer. You see:

OR

Dial or press MORE + OFFP for Off Premise

Call Forwarding. (See Call Forwarding Off Premise on
page 21 for more.) You see:

OR

12
80000mfh08-01.qxd 12/10/04 3:20 PM Page 13

Call Forwarding

Dial or press MORE + AME for Personal

Answering Machine Emulation. (See Voice Mail on page
188 for more.) You see:

OR

Dial or press MORE + MSG to select a

Selectable Display Message. (See Selectable Display
Messaging on page 163 for more.)
3. Dial destination extension or 0 (or 01-04) for your operator.
OR
Dial the Voice Mail master number.
OR

Press .
4. Select the Call Forwarding type:
– Dial 2 or press ALL to forward all calls.
– Dial 8 or press TRNK to forward just outside calls.
If you forward your calls immediately to a co-
worker, only the user at the forwarding destination
can call you on the Intercom.

13
80000mfh08-01.qxd 12/10/04 3:20 PM Page 14

Call Forwarding
To cancel Call Forwarding

1. Press and dial , or press your Call

Forwarding key.
OR

Press + PGM + CFWD . You see:

2. Dial , press , or press NONE to cancel Call

Forwarding.

14
80000mfh08-01.qxd 12/10/04 3:20 PM Page 15

Call Forwarding
Call Forwarding at your Super Display Telephone
To activate Call Forwarding:

1. Press and dial , or press your Call

Forwarding key.
OR
Press PROGRAM + CALL FWRD . You see:

2. Dial or press IMMEDIATE for Call Forwarding

Immediate. You see:

OR

15
80000mfh08-01.qxd 12/10/04 3:20 PM Page 16

Call Forwarding

Dial or press RING/NO ANS for Call Forwarding

No Answer. You see:

OR

Dial or press BUSY/NO ANS for Call Forwarding

Busy/No Answer. You see:

OR

16
80000mfh08-01.qxd 12/10/04 3:20 PM Page 17

Call Forwarding

Dial or press OFF-PREMISE for Off Premise Call

Forwarding. (See Call Forwarding Off Premise on page
21 for more.) You see:

OR

Dial or press ANS MACHINE for Personal

Answering Machine Emulation. (See Voice Mail on page
188 for more.) You see:

OR

17
80000mfh08-01.qxd 12/10/04 3:20 PM Page 18

Call Forwarding

Dial or press MESSAGE to select a Selectable

Display Message. (See Selectable Display Messaging on
page 163 for more.) You see:

3. Dial destination extension or 0 (or 01-04) for your operator.

OR
Dial the Voice Mail master number.
OR

Press . You see:

18
80000mfh08-01.qxd 12/10/04 3:20 PM Page 19

Call Forwarding
4. Select the Call Forwarding type:
– Dial 2 or press ALL to forward all calls.
– Dial 8 or press TRUNK ONLY to forward just outside
calls.
If you forward your calls immediately to a co-
worker, only the user at the forwarding destination
can call you on the Intercom.

19
80000mfh08-01.qxd 12/10/04 3:20 PM Page 20

Call Forwarding
To cancel Call Forwarding

1. Press and dial , or press your Call

Forwarding key.
OR
Press PROGRAM + CALL FWRD . You see:

2. Dial .
OR
Press NONE .
OR

Press .

20
80000mfh08-01.qxd 12/10/04 3:20 PM Page 21

Call Forwarding Off Premise

Set up a your
Redirect multiple-party
calls to
If you have a display keyset, Off
telephone meeting
your cell phone or your Premise Call Forwarding allows
without leaving
home office. the office. you to forward your calls to an
off-site location (such as a cell
phone or remote office). You can
stay in touch by having Off Premise Call Forwarding automatical-
ly forward your calls while you are away from the office.

To set up Off Premise Call Forwarding, select the line or line

group over which the call should route, as well as the number the
system should dial. The number dialed can be one of your
Personal Speed Dial bins containing an outside number, or you
can enter an outside number directly into Personal Speed Dial bin
720. When a call rings your extension, the system selects the
specified line or group and then outdials the stored number.

Off Premise Call Forwarding reroutes:

● Intercom calls
● Transferred calls
● Direct Inward Lines (Remember that a line can be a regular
line during the day and a DIL at night, and visa versa.)
● UTRF (unscreened transfer) calls routed from the Voice Mail
Automated Attendant
● Circular and Terminal Extension Hunting calls

Off Premise Call Forwarding does not reroute:

● Key Ring calls
● Calls to a UCD Group master number.
● Group Ring calls (i.e., calls to a Ring Group master number)
● UCD Hunting Calls (i.e., calls to a UCD master number)
● Ringing Call Coverage key calls

You can set up Off Premise Call Forwarding to reroute all calls or
just outside calls.

21
80000mfh08-01.qxd 12/10/04 3:20 PM Page 22

Call Forwarding Off Premise

Off Premise Call Forwarding at your 22-Button or
34-Button Telephone
To set up Call Forwarding Off Premise:

1. Press the and dial , or press your Call

Forwarding key.
OR
Press PGM + CFWD . You see:

2. Dial and skip to step 5.

OR
Press MORE . You see:

3. Press OFFP .
4. You see:

– Press BIN to select a Speed Dial bin as your Off

Premise Call Forwarding number.
– Press NUM to store a new Off Premise Call
Forwarding number (automatically in bin 720).
– Press VIEW to view the currently enabled Off
Premise Call Forwarding number (if any).

22
80000mfh08-01.qxd 12/10/04 3:20 PM Page 23

Call Forwarding Off Premise

5. If you press BIN to store the number in a Speed Dial
bin, you see:

– Select the Speed Dial bin (dial 701-720 or press the bin
key) you want to use + HOLD to exit.
OR
If you press NUM to store a new number (automati-
cally in Speed Dial bin 720), you see:

– Enter the line number (e.g., 1 for line 1), line group
number (e.g., 90 for group 0), or ICM to store Intercom
codes + HOLD. (Check with your Communications
Manager for your line and line group numbers.)
– Following Speed Dial programming methods, enter the
number you want to store (up to 16 digits long, includ-
ing MIC to store a pause and FLASH to store a Flash) +
HOLD to exit.
– You cannot enter a name using this option.
– If you already have a number stored in bin 20, you see:

– Press YES to enter a new number or NO to

back up to step 4.
OR

23
80000mfh08-01.qxd 12/10/04 3:20 PM Page 24

Call Forwarding Off Premise

If you pressed VIEW to view your currently stored
number, you see:

– Press SPK to exit the VIEW mode.

6. You see:

7. Select the Call Forwarding type:

– Dial 2 or press ALL to forward all calls.
– Dial 8 or press TRNK to forward just outside calls.
8. Once returning to idle, your telephone display will show:

– FWD OFP indicates that Off Premise Call Forwarding

is enabled, followed by the number.
– If you selected a Speed Dial bin with a stored name,
the name will display instead.

To cancel Call Forwarding Off Premise:

1. Press the and dial , or press your Call

Forwarding key.
OR

Press + PGM + CFWD . You see:

24
80000mfh08-01.qxd 12/10/04 3:20 PM Page 25

Call Forwarding Off Premise

2. Press NONE .
OR

Dial .
OR

Press .

Off Premise Call Forwarding at your Super Display

Telephone
To set up Call Forwarding Off Premise:

1. Press the and dial , or press your Call

Forwarding key
OR
Press PROGRAM + CALL FWRD . You see:

25
80000mfh08-01.qxd 12/10/04 3:20 PM Page 26

Call Forwarding Off Premise

2. Dial or press OFF-PREMISE . You see:

– Press SPEED DIAL BIN to select a Speed Dial bin as

your Off Premise Call Forwarding number.
– Press NUMBER to store a new Off Premise Call
Forwarding number (automatically in bin 720).
– Press VIEW to view the currently enabled Off
Premise Call Forwarding number (if any).
3. If you press SPEED DIAL BIN to store the number in a
Speed Dial bin, you see:

- Select the Speed Dial bin (701-720) you want to use +

HOLD to exit.
OR

26
80000mfh08-01.qxd 12/10/04 3:20 PM Page 27

Call Forwarding Off Premise

If you press NUMBER to store a new number (automatically
in Speed Dial bin 720), you see:

– Enter the line number (e.g., 1 for line 1), line group
number (e.g., 90 for group 0), or ICM to store Intercom
codes + HOLD. (Check with your Communications
Manager for your line and line group numbers.)
– Following Speed Dial programming methods, enter the
number you want to store (up to 16 digits long, includ-
ing MIC to store a pause and FLASH to store a Flash) +
HOLD to exit.
– You cannot enter a name using this option.
– If you already have a number stored in bin 20, you see:

– Press YES to enter a new number or NO to

back up to step 3.
OR

27
80000mfh08-01.qxd 12/10/04 3:20 PM Page 28

Call Forwarding Off Premise

If you pressed VIEW to view your currently stored
number, you see:

– Press SPK to exit the VIEW mode.

4. You see:

5. Select the Call Forwarding type:

– Dial 2 or press ALL to forward all calls.
– Dial 8 or press TRUNK ONLY to forward just outside
calls.
6. Once returning to idle, your telephone display will show:

28
80000mfh08-01.qxd 12/10/04 3:20 PM Page 29

Call Forwarding Off Premise

– FWD OFP indicates that Off Premise Call Forwarding

is enabled, followed by the number.
– If you selected a Speed Dial bin with a stored name,
the name will display instead.

To cancel Call Forwarding Off Premise:

1. Press and dial , or press your Call

Forwarding key
OR
Press PROGRAM + CALL FWRD . You see:

2. Press NONE .
OR
Dial 0.
OR

Press .
29
80000mfh08-01.qxd 12/10/04 3:20 PM Page 30

Call Forwarding Off Premise

If you have a 22-Button Non-Display Telephone
It is strongly recommended that you use a display telephone
when setting up Off Premise Call Forwarding. If you don’t
have a display telephone, the following procedure explains
how you can use a 22-button non-display set to enable Off
Premise Call Forwarding.
To set up Call Forwarding Off Premise:
1. Program the number that Call Forwarding Off Premise
should dial into a Personal Speed Dial bin (701-720).
– You must do this before proceeding to step 2 below.
– For example, the following sequence programs the
number 12039265400 with the name NEC to go out
over line group 0:
#77 + 701 + HOLD + 90 + HOLD + 12039265400 +
HOLD + 62 + 32 + 23 + HOLD + SPK.

2. Press key and dial .

3. Dial and enter the Personal Speed bin number you

programmed in step 1 above + HOLD.
4. Select the Call Forwarding type:
– Dial 2 to forward all calls.
– Dial 8 to forward just outside calls.
– Your DND key flashes.
To cancel Call Forwarding Off Premise:

1. Press and dial .

- Your DND key goes out.

30
80000mfh08-01.qxd 12/10/04 3:20 PM Page 31

Call Screening (with IntraMail)

With IntraMail, screen

If you have a display keyset, Call
(listen to) a Voice Mail Screening lets you listen to
message while it is being (screen) a voice mail message as
it is being left in your IntraMail
left in your mailbox. mailbox. Call Screening emulates
a standard home answering
machine — in addition to providing more control when handling
incoming messages. Similar to Personal Answering Machine
Emulation, you can listen as the message is being left, intercept
the call, or end the screen and have the message recorded private-
ly. Unlike Personal Answering Machine emulation, Call Screening
does not require you to forward your calls immediately to voice
mail. Your telephone’s display automatically shows the Call
Screening soft key options as soon as the recording begins.

When enabled, Call Screening will broadcast your caller’s mes-

sage as soon as your mailbox greeting completes. Additionally, if
you intercept (answer) the screened call, the first portion of the
message is automatically erased from the extension’s mailbox.

Notes
● Any caller that can leave a message can have their call screened.
● If more than one caller is leaving a message in your mailbox
simultaneously, Call Screening will listen to the first message.
● Call Screening is only available with IntraMail.

Call Screening and Group Mailboxes

If you share a Group Mailbox with co-workers, any number of
extensions in your group can screen an incoming message. Your
group’s extensions can monitor the incoming message simultane-
ously. If any member of your group answers the call (i.e., inter-
cepts the incoming message), the remaining group members are
immediately disconnected.

31
80000mfh08-01.qxd 12/10/04 3:20 PM Page 32

Call Screening (with IntraMail)

Automatic Call Screening
With Automatic Call Screening enabled, your extension will
immediately screen (broadcast) an incoming message as soon as
the caller starts to leave the message in your mailbox. You hear
two beeps followed by the caller’s voice.

MW LED Operation Change

If your system provides Call Screening capability, only your
Ring/Message Lamp flashes for new messages. Your MW LED is
used for Call Screening only.

Using Manual Call Screening

When Automatic Call Screening is off, you hear a single beep and
MW flashes fast while IntraMail records your caller’s message.
Your telephone display automatically changes to show the Call
Screening soft key options. Call Screening is only available while
your telephone is idle.
To intercept the call (and stop recording the message):
● Press ANSWER (ANSW) or flashing MW.

To hear your caller’s message as it is recorded in your mail-

box (i.e., activate the Call Screening mode):
●. Press SCREEN (SCRN) .
— To intercept the call (and stop recording the message):
Press ANSWER (ANSW) , or
Press SPK, or
Lift the handset, or
Press MW.

32
80000mfh08-01.qxd 12/10/04 3:20 PM Page 33

Call Screening (with IntraMail)

— To continue listening to your caller’s message as it is
being recorded:
Do nothing.
— To exit Call Screening and allow the message to continue
recording in private:
Press EXIT .
— To use another feature or process another call:
Press any other feature key.

To exit Call Screening and allow the message to continue

being recorded in private:
● Press EXIT .

To use another feature or process another call:

● Lift the handset, or
Press SPK, or
Press any other feature key.
Call Screening is only functional while the tele-
phone is on-hook.

Using Automatic Call Screening

When Automatic Call Screening is on, your idle telephone automat-
ically goes into the screen mode while your caller leaves a mes-
sage. Call Screening is only available while your telephone is idle.
To turn Automatic Call Screening on or off:
1. Super Display Telephone
Press PROGRAM + SCREEN .
22-Button or 34-Button Display Telephone
Press PGM + MORE + MORE + SCRN .

33
80000mfh08-01.qxd 12/10/04 3:20 PM Page 34

Call Screening (with IntraMail)

2. Press ON to turn Automatic Call Screening on.
OR
Press OFF to turn Automatic Call Screening off.
The top line of the display shows the Automatic
Call Screening status.
3. Press EXIT to exit.

To intercept the call (and stop recording the message):

●. Press ANSWER (ANSW) , or
Press SPK, or
Lift the handset, or
Press MW.

To continue listening to your caller’s message as it is being

recorded:
● Do nothing.

To exit Call Screening and allow the message to continue

recording in private:
● Press EXIT .

To use another feature or process another call:

● Press EXIT + Lift the handset or press any other fea-
ture key.

34
80000mfh08-01.qxd 12/10/04 3:20 PM Page 35

Call Timer

Set up a multiple-party
Keep track of your time If your phone has a Call Timer
telephone meeting key, your display can keep track
on the phone.
without leaving the office. of your time on a call.

There are two types of Call Timer keys:

● Manual Call Timer
Any time while placing a call or while on a call, you can
press your Manual Call Timer key to start the Call Timer. The
Call Timer will continue until you hang up or press your
Manual Call Timer key again. The Manual Call Timer can
time both Intercom and outside calls.
● Automatic Call Timer
In addition to the features of the Manual Call Timer key, the
Automatic Call Timer key provides automatic timing for out-
side calls only. If your phone has an Automatic Call Timer
key, the Call Timer automatically starts when you place or
answer an outside call. The Automatic Call Timer does not
automatically start for Intercom calls.

Enhanced Call Timer

In addition to the capabilities of the Call Timer feature, Enhanced
Call Timer provides (if you have a display set):
● Review of Previously Timed Call
Any time after hanging up from a timed call, you can press
your Manual or Automatic Call Timer key to review the dura-
tion of that call.
● Timer Reset for Current Call
While your phone is timing your call, you can press CLEAR
at any time to reset the Call Timer to 00:00:00.
● Automatic Timer Stop
The system assigns the Call Timer to the active call. When
you hang up on your active call, the Call Timer automatically
shuts down.

35
80000mfh08-01.qxd 12/10/04 3:20 PM Page 36

Call Timer
● Wrap-up Timer Display
After hanging up a timed call, your display will show the
Call Timer data for 6 seconds before returning to idle. This
gives you time to make a record of the timed call.

To time your outside call if you have an Automatic Call

Timer key:
1. Place or answer outside call.
– The Call Timer starts automatically. The Automatic Call
timer key lights red while the system times the call.

To manually time your Intercom or outside call:

1. While placing or while on the call, press the Manual or
Automatic Call Timer key.
– The Call Timer key lights red while the system times
the call.
OR
1. Press your TIME or TIMER soft key.

To stop the Call Timer:

1. Hang up.
- The timer automatically stops after 6 seconds.
OR
1. Press the Manual or Automatic Call Timer key.

To reset the Call Timer to 00:00:00 while it is running (i.e.,

timing your call):

1. Press .

36
80000mfh08-01.qxd 12/10/04 3:20 PM Page 37

Call Timer
To review the duration of your last timed call:
1. While idle, press the Manual or Automatic Call Timer
key.
– Press CLEAR or wait 6 seconds to return to idle
Time/Date display.

37
80000mfh08-01.qxd 12/10/04 3:20 PM Page 38

Call Waiting / Camp-On

Set upwhen
Know a multiple-party
you have
With Call Waiting, a co-worker
telephone
calls waiting,
meeting
or wait in can call you while you’re busy
without
line for aleaving
busy co-worker.
the office. and wait in line (Camp-On) for
you to become free. You’ll hear
two beeps indicating that your
co-worker is waiting. The call goes through when your extension
becomes free.

Note: If you have more than one caller waiting, they queue (i.e.,
wait in line for you) on a first-in/first-out basis. You hear
Camp-On beeps only for the first waiting call.
To Camp-On to a busy extension:
1. Call a busy co-worker.

2. Dial or press CAMP .

3. Do not hang up.
If you hang up, the system converts your
Camp-On to a Callback.
4. When your co-worker becomes free, you hear ringback.
5. Speak to your co-worker when they answer their wait-
ing call.

38
80000mfh08-01.qxd 12/10/04 3:20 PM Page 39

Callback
You don’t have to
repeatedly call a busy When you call a busy co-worker,
you can leave a Callback request
co-worker back, hoping to for a return call. There is no need
find them idle. to keep calling your co-worker
back, hoping to find them idle.

Here’s how Callback works:

● You call a busy co-worker and leave a Callback.
● When your co-worker becomes free, your phone automatically
starts ringing.
● Once you lift the handset to answer the ring, your co-worker
then rings.
● As soon as your co-worker answers, you’ll have an Intercom
call between yourself and your co-worker.

To leave a Callback at a busy co-worker:

1. Call your busy co-worker.

2. Dial or press CLBK .

3. Hang up.
If you stay on the line, you will Camp-On to your
busy co-worker.
4. When your busy co-worker becomes free, your phone
will automatically ring.
5. Lift the handset to answer.
6. Speak to your co-worker when the call goes through.

39
80000mfh08-01.qxd 12/10/04 3:20 PM Page 40

Caller ID

Your display can show

Caller ID allows your telephone
your outside caller’s display to show the incoming
phone number and caller’s telephone number and
optional name. Caller ID supports
optional name. your telephone company’s Called
Number Identification (CNI) and
Called Number Delivery (CND) service, when available.

Single and Multiple Message Format

There are two types of Caller ID message formats available: Single
Data Message Format (SDMF) and Multiple Data Message Format
(MDMF). If your telephone company supports Single Data Message
Format, you’ll see only your caller’s number. With Multiple Data
Message Format, you’ll see both your caller’s number and name.

Caller ID and NVM-Series Voice Mail

Caller ID works with your NVM-Series Voice Mail system to pro-
vide productivity enhancements like Make Call with Caller ID.
With Make Call, you can return a call to someone who left you a
message without knowing your caller’s phone number. Your
Communications Manager can tell you if you have this capability.

Second Call Caller ID

While you are busy on a call, your telephone display can show
you the Caller ID information for a waiting call. If you receive
Camp On tones or Off-Hook Ringing for a call, you can also
receive the Second Call Caller ID. Check with your
Communications manager to see if you have this feature.

Third Party Caller ID Check

Third Party Caller ID Check allows you to see the Caller ID infor-
mation for a co-worker’s call. Check with your Communications
Manager for more about Third Party Caller ID Check.

40
80000mfh08-01.qxd 12/10/04 3:20 PM Page 41

Caller ID
To cancel the Caller ID display and return your phone to
its normal display:
You can only do this while you’re on a call, not
while your phone is ringing.

1. Press .

To turn the Caller ID display back on (after you press

CLEAR to cancel it):

1. Press .

The display the Caller ID information for a co-worker’s (i.e.,

a third party) call:

1. Press + .
2. Press the key for the call you want to check.
You can press a line key, loop key, Hotline key or
Call Coverage key.
— Press a line key while the call is ringing or con-
nected to the third party.
— Press a loop key while the call is ringing the third
party.
— Press a Hotline key while the call is connected to
the third party.
— Press a Call Coverage key while the call is ring-
ing the third party.
3. Hang up when you are done.

41
80000mfh08-01.qxd 12/10/04 3:20 PM Page 42

Caller ID Logging

Your phone can store

If your system has Caller ID
your caller’s name and enabled, Caller ID logging stores in
phone number for easy a log your caller’s number and
optional name for each outside call
review and redialing. that rings the system. You can view
this log on your telephone display,
allowing you to easily review and redial your calls.

The system can log calls directly to your extension — or you

may be a member of a Caller ID Logging group that shares
records. Your Communications Manager can tell you more.

Use the feature and soft keys on your phone to:

● Scroll through (review) your Caller ID records.
● Delete records you no longer need.
● Store a record (both the number and name) in one of your
Personal Speed Dial bins.
● Place a return call to the calling party.

Caller ID Logging at your 22-Button or 34-Button

Display Telephone
To review your Caller ID log:

1. While your phone is idle, press CLnn (where nn is the

number of Caller ID records currently logged at your phone).
– Your Ring/Message Lamp (the large green LED on the
upper right corner of your phone) winks on (green) when
you have Caller ID records you have not reviewed.
– After pressing CLnn , you see:

42
80000mfh08-01.qxd 12/10/04 3:20 PM Page 43

Caller ID Logging

– Total = the total number of Caller ID records in your log.

– New = the number of new calls since you last
reviewed your log.
2. While this display is on screen, you can:
– Press ALL to review all your Caller ID records.
– Press UNAN to review the records just for calls that
rang your phone but were unanswered in the system.
– Press DEL* to delete all Caller ID records logged at
your phone.
– Press EXIT or dial 9 to exit to the idle mode with-
out making any changes.
3. If you pressed ALL or UNAN in the previous step,
you see (for example):

This display is Page 1 of a Caller ID record. It shows:

– The name of the person that called (if available). The
most recent call displays first.
– The call record number (e.g., 03).
– The date they called (i.e., Yesterday, Today or day of
week and date).
4. Press . You see (for example):

This display is Page 2 of a Caller ID record. It shows:

– Your caller’s phone number.
– The call record number (e.g., 03).

43
80000mfh08-01.qxd 12/10/04 3:20 PM Page 44

Caller ID Logging
– The outside line number (or name – if programmed)
the call came in on.
– The extension that answered the call, or if the call
was unanswered.
5. Use and to scroll through the Caller ID
records that are logged at your phone.
6. Press to toggle between Page 1 and Page 2.
7. When a Caller ID record is displayed, you can:
– Press to call the person back.

– Dial to Store the number in Personal Speed Dial.

– Dial to Delete the displayed record.

– Dial to eXit (go back to step 2).

– Press to show the Caller ID Menu display below.

8. While the Caller ID Menu displays, you can:

– Press CALL to call the person back.
– Press STOR to store the number in Personal Speed
Dial.
– Press DEL to delete the displayed record.
– Press EXIT to go back to step 2.
– Press to back up to step 7.

44
80000mfh08-01.qxd 12/10/04 3:20 PM Page 45

Caller ID Logging
Caller ID Logging at your Super Display Telephone
To review your Caller ID log:

1. While idle, press CALLS nn (where nn is the number of

Caller ID records currently logged at your phone).
– Your Ring/Message Lamp (the large green LED on the
upper right corner of your phone) winks on (green) when
you have Caller ID records you have not reviewed.
– After pressing CALLS nn , you see:

– Total = the total number of Caller ID records in your log.

– New = the number of new calls since you last
reviewed your log.
– Unans = the number of Caller ID calls that rang your
phone that were unanswered in the system.
– Ans = the number of Caller ID calls that rang your
phone that were answered in the system.

45
80000mfh08-01.qxd 12/10/04 3:20 PM Page 46

Caller ID Logging
2. While this display is on screen, you can:
– Press VIEW ALL to review all your Caller ID records.
– Press VIEW UNANS to review the records just for calls
that rang your phone but were unanswered in the system.
– Press DELETE ALL to delete all Caller ID records
logged at your phone.
– Press VIEW ANS to review the records just for the calls
that rang your phone that were answered in the system.
– Press EXIT or dial 9 to exit to the idle mode without
making any changes.
3. If VIEW ALL , VIEW UNANS , or VIEW ANS were
pressed in the previous step, you see (for example):

This display is a Caller ID record. It shows:

– The name of the person that called (if available). The
most recent call displays first.
– The call record number (e.g., 03).
– Your caller’s phone number.
– The date they called (i.e., Yesterday, Today or day of
week and date).
– The time they called.
– The outside line number (or name – if programmed)
the call came in on.
– The extension that answered the call, or if the call
was unanswered.

46
80000mfh08-01.qxd 12/10/04 3:20 PM Page 47

Caller ID Logging

4. Use and to scroll through the Caller ID

records that are logged at your phone.
5. When a Caller ID record is displayed, you can:
– Press CALLBACK to call the person back.
– Press DELETE to delete the displayed record.
– Press STORE BIN to store the number in a Personal
Speed Dial bin.
– Press DELETE ALL to delete all your Caller ID records.
– Press EXIT to go back to step 1.

47
80000mfh08-01.qxd 12/10/04 3:20 PM Page 48

Central Office Calls, Answering

Set up a multiple-party
Normally, outside calls ring Outside calls can ring your exten-
telephone meeting sion directly, without having to be
your extension directly.
without leaving the office. transferred by your company’s
operator or receptionist.

To answer an outside call:

Outside calls normally flash red on your line/loop
keys. If a line/loop key is flashing green, the call is a
Direct Inward Line (DIL) to your phone.
The call may also ring your phone.
You may have a Private Line that rings only your
phone. Check with your Communications Manager.
1. Lift handset.
If you have Ringing Line Preference, lifting the
handset answers the call.
If you have Automatic Handsfree, you can press a
line/loop key without first lifting the handset.
2. Press the flashing line/loop key.
If you hear ringing over the Paging speakers, you
may be able to dial *0 to pick up the call.

User Programmable Feature

#RAL
Change the ringing mode of your line keys. See User
Programmable Features at the end of this guide for more.

48
80000mfh08-01.qxd 12/10/04 3:20 PM Page 49

Central Office Calls, Placing

Set up
Your a multiple-party
system offers many
There are many different ways
telephone meeting
convenient ways to place you can place outside calls.
without leaving
outside calls. the office. Choose the one which works best
for you. Check with your
Communications Manager to find
out what options are available on your phone.

Following is a list of your options for placing outside calls:

● Pressing a Line Key
Normally, you have line keys on your phone for outside calls.
If you do, you can just press the key to place a call.
● Pressing a Loop Key
If you have a Loop Key, pressing the key will give you the
first available outside line from a preset group of lines.
● Using Line Dial-Up
Line Dial-Up allows you to select a line for an outside call by
dialing the Line Dial-Up code (#9) and a line number (e.g., 01).
● Using Direct Trunk Access
With Direct Trunk Access, you can get a line for an outside
call by dialing the line’s extension number. For example, line
1 is normally line extension number 401.
● Dialing a Trunk Group Access Code
You can place a call on the first available line in a line group
by dialing the group’s number (e.g., 90).
● Line Group Routing
Line Group Routing lets you select a line for an outgoing call
just by dialing 9.

Store and Forward

If your system has Store and Forward, it waits until you have fin-
ished dialing before redialing your call on an outside line. Check
with your Communications Manager to find out if you have Store
and Forward enabled.

49
80000mfh08-01.qxd 12/10/04 3:20 PM Page 50

Central Office Calls, Placing

To place a call using a line or loop key:
1. Press the key.
The key will light green and you’ll hear dial tone
from your outside line.
If you have Store and Forward enabled and are
using a loop key, the system will dial out your call 6
seconds after you dial the last digit. To avoid wait-
ing, dial # after dialing your last digit.
You may have a Private Line that is only on your
phone. Check with your Communications Manager.
2. Dial the outside number you want to call.
Toll Restriction may prevent you from dialing cer-
tain outside numbers.
If you use a dial pulse line and wait 6 seconds
after dialing a digit, the system outdials any remain-
ing digits as tone (DTMF).

50
80000mfh08-01.qxd 12/10/04 3:20 PM Page 51

Central Office Calls, Placing

To place a call over a specific line (using Line Dial-Up or
Direct Line Access):

1. Press .
2. For Line Dial-Up:

Dial + + line number (e.g., 01 for line 1).

OR
For Direct Trunk Access:

Dial + line number (e.g., 01 for line 1).

3. Dial the outside number you want to call.
Toll Restriction may prevent you from dialing cer-
tain outside numbers.
If you use a dial pulse line and wait 6 seconds
after dialing a digit, the system outdials any remain-
ing digits as tone (DTMF).

51
80000mfh08-01.qxd 12/10/04 3:20 PM Page 52

Central Office Calls, Placing

To place a call over a line group (using a Line Group
Access Code or Line Group Routing):

1. Press .
2. Dial a Line Group Access Code (90-98).
Dial 90 for group 0, 91 for group 1, etc.
If you hear dial tone as soon as you dial 9, your
system has Line Group Routing. (A line group has
been automatically selected for you.)
If you have Store and Forward enabled, the sys-
tem will dial out your call 6 seconds after you dial
the last digit. To avoid waiting, dial # after dialing
your last digit.
3. Dial the outside number you want to call.
Toll Restriction may prevent you from dialing cer-
tain outside numbers.
If you use a dial pulse line and wait 6 seconds
after dialing a digit, the system outdials any remain-
ing digits as DTMF.

52
80000mfh08-01.qxd 12/10/04 3:20 PM Page 53

Central Office Calls, Placing

– For Your Notes –

53
80000mfh08-01.qxd 12/10/04 3:20 PM Page 54

Conference
Set up a multiple-party
Conference lets you add additional
telephone meeting
inside and outside callers to your
without leaving the office. conversation. In addition to
Conference, there are other ways
to have a telephone meeting. Refer also to Barge In, Group Listen,
Meet-Me Conference, Privacy Release Groups and Tandem
Trunking (Unsupervised Conference).
To set up a Conference:
1. Establish Intercom or outside call.

2. Press .
OR
CONF .
3. Dial extension you want to add.
OR
Place or answer outside call.
OR
Retrieve call from Park Orbit.

4. Press to set up the Conference.

If you cannot add additional parties to your
Conference, you have exceeded the system’s
Conference limit. Try again later.

54
80000mfh08-01.qxd 12/10/04 3:20 PM Page 55

Dial Number Preview

Avoid dialing errors by
previewing your call With Dial Number Preview, you
can dial and review a number
before you dial it. before the system dials it out.

To dial using Dial Number Preview:

1. Do not lift the handset, press or press .

2. Dial .
3. Dial the number you want to call.
If you make a dialing mistake, refer to Correcting
the Displayed Digits below.
4. Press a line key to have the system dial your call.

Correcting the Displayed Digits

If you make a mistake entering digits while using Dial Number
Preview, you can correct your entry before the systems dials the call.
To correct the displayed digits before dialing them out:

1. Use or until the cursor replaces the digit

you want to change.
2. Dial the digit that you want to have replace the cursor.

3. Press or to place the cursor over any other

digits you want to edit.
OR

Press until the entire number displays to the left

of the cursor.
The system will only dial the digits to the left of the
cursor.

55
80000mfh08-01.qxd 12/10/04 3:20 PM Page 56

Dial Number Preview

4. Press a line key to have the system automatically dial the
displayed number.

Dial Number Preview Editing Example

To replace 2049265410 with 203-926-5400:

1. Dial + 2049265410. You see: 2049265410-

2. Press until you see: 20-9265410

3. Dial . You see: 203-265410

4. Press until you see: 20392654-0

5. Dial . You see: 203926540-

6. Press until the entire number

displays to the left of the cursor. 2039265400-
7. Press a line key to dial the number.

56
80000mfh08-01.qxd 12/10/04 3:20 PM Page 57

Direct Station Selection (DSS)

Quickly place and Transfer
calls to co-workers. If the DSS feature is enabled for
your phone, all your Programmable
Function Keys become DSS keys when you press ICM. This
gives you one-button Intercom access and Transfer to co-work-
ers. (If this “key toggling” operation is not desirable, consider
using the Hotline or Call Coverage Keys features instead.)
DSS keys also show the status of the assigned extension.

DSS Key Flash Rates

When the key is: The covered extension is:
Off Idle or not installed
On Busy or ringing
Flashing Fast In Do Not Disturb

To place a call to a co-worker using a DSS key:

1. Press .
2. Press DSS key for the co-worker you want to call.

To Transfer an outside call to a co-worker using a DSS key:

1. Place or answer outside call, then press .
Your DSS keys show the status of the extensions
to which they are assigned.
2. Press DSS key for co-worker.
3. Hang up to have the Transfer go through unscreened.
To screen, first wait for the called party to answer.
User Programmable Feature
#BLF
Use this option to change your DSS key assignments. The
assignments you make take effect only if you have the
DSS feature enabled. See User Programmable Features
at the end of this guide for more.

57
80000mfh08-01.qxd 12/10/04 3:20 PM Page 58

Direct Station Selection Console

Use your DSS Console

Your optional DSS Console pro-
for one-touch access to vides additional one-button access
co-workers, outside lines to co-workers, outside lines and
system features. If you do a lot of
and system features. call processing, your console will
be a welcome convenience.

There are two types of DSS Consoles:

the 24-Button and the 110-Button. Each
console has the same capability, limited
by the number of available keys.

Note: You can only have a DSS Console if you have a 34-Button
Display or 34-Button Super Display telephone.

The following chart shows the available DSS Console key func-
tions and the Busy Lamp Field (BLF) flash rates for each key.
The chart also provides a brief guide on how to use the key.
Check with your Communications Manager to see which keys are
assigned to your console.

By default, 110-Button DSS Console keys 1-80 are Hotline keys

to extensions 300-379. Keys 97-110 are reserved for special func-
tions (like Page zones and Park orbits). With the 24-Button DSS
Console, keys 1-24 are Hotline keys to extensions 300-323. See
page 62 for more on the DSS Console default assignments.

58
80000mfh08-01.qxd 12/10/04 3:20 PM Page 59

Direct Station Selection Console

DSS Console Key Assignments

Account Code
Key Code: . . . . . . . . . . . . . . .26
BLF: . . . . . . . . . . . . . . . . . . .Off: Account Code inactive
On: Account Code active for call
Fast Flash: Account Code entry mode
Operation: . . . . . . . . . . . . . . .Press to enter Account Code, then
press again to return to call.
Call Coverage
BLF: . . . . . . . . . . . . . . . . . . .Off: Co-worker idle
On: Co-worker busy
Fast Flash: Co-worker in DND
Operation: . . . . . . . . . . . . . . .Press to call co-worker or pick up ring-
ing call.
Call Forwarding
Key Code: . . . . . . . . . . . . . . .27
BLF: . . . . . . . . . . . . . . . . . . .Off: Call Forwarding disabled
Fast Flash: Extension in Call
Forwarding programming mode
Wink Off: Call Forwarding enabled
Operation: . . . . . . . . . . . . . . .While idle, enters Call Forward pro-
gramming mode. While busy, switches
Call Forwarding on and off.
Conversation Record
BLF: . . . . . . . . . . . . . . . . . . .Off: Recording Off
On: Recording Being Set Up
Fast Flash: Recording On
Operation: . . . . . . . . . . . . . . .Press to record conversation in mailbox.
Group Pickup
BLF: . . . . . . . . . . . . . . . . . . .Off: No call ringing group
Slow Flash: Call ringing group
Operation: . . . . . . . . . . . . . . .Press key to answer call ringing Pickup
Group.
Headset Mode
Key Code: . . . . . . . . . . . . . . .28
BLF: . . . . . . . . . . . . . . . . . . .Off: Headset mode disabled
On: Headset mode enabled
Operation: . . . . . . . . . . . . . . .Press to enable/disable headset mode.

59
80000mfh08-01.qxd 12/10/04 3:20 PM Page 60

Direct Station Selection Console

DSS Console Key Assignments (Cont’d)
Hotline
BLF: . . . . . . . . . . . . . . . . . . .Off: Partner is idle
On: Partner is ringing or busy
Fast Flash: Partner in DND
Operation: . . . . . . . . . . . . . . .Press to call Hotline partner.
Intercom Directory Dialing
BLF: . . . . . . . . . . . . . . . . . . .Off: Inactive
On: Active
Operation: . . . . . . . . . . . . . . .Press key to access Intercom Directory
Dialing.
Line Keys
BLF: . . . . . . . . . . . . . . . . . . .Off: Line idle or not installed
On: Line busy
Slow Flash: Line ringing
Operation: . . . . . . . . . . . . . . .Press to place or answer call on out-
side line.
Message Center
BLF: . . . . . . . . . . . . . . . . . . .Off: No messages in Message Center
Fast Flash: Messages are waiting in
Message Center
Operation: . . . . . . . . . . . . . . .Press to see how many messages are
waiting in Message Center.
OR
Press SPK + key to call Message
Center.
Night Key
BLF: . . . . . . . . . . . . . . . . . . .Off: System in Day Mode
On: System in Night Mode
Operation: . . . . . . . . . . . . . . .Press to switch Day/Night Mode of the
system.
Page Zones
BLF: . . . . . . . . . . . . . . . . . . .Off: Page Zone idle
On: Page Zone busy
Operation: . . . . . . . . . . . . . . .Press to Page into assigned zone.
Park Orbits
BLF: . . . . . . . . . . . . . . . . . . .Off: Park Orbit idle
On: Has a call parked by a co-worker
Wink On: Has a call you parked
Operation: . . . . . . . . . . . . . . .Press to Park or retrieve call from orbit.

60
80000mfh08-01.qxd 12/10/04 3:20 PM Page 61

Direct Station Selection Console

DSS Console Key Assignments (Cont’d)
Reverse Voice Over
BLF: . . . . . . . . . . . . . . . . . . .Off: Co-worker idle
On: Co-worker busy or ringing
Fast Flash: Co-worker in DND
Operation: . . . . . . . . . . . . . . .While on handset call, press key to
place private Intercom call to co-worker.
Save
BLF: . . . . . . . . . . . . . . . . . . .No BLF
Operation: . . . . . . . . . . . . . . .While on a call, press key to Save
number you just dialed.
OR
While idle, press key to redial previously
saved number.
Personal or System Speed Dial
BLF: . . . . . . . . . . . . . . . . . . .No BLF
Operation: . . . . . . . . . . . . . . .Press to dial stored number.
Split
BLF: . . . . . . . . . . . . . . . . . . .No BLF
Operation: . . . . . . . . . . . . . . .Press to switch between calls. See the
Split feature in this handbook for more.

61
80000mfh08-01.qxd 12/10/04 3:20 PM Page 62

Direct Station Selection Console

Default DSS Console Key Assignments
The illustrations below show your DSS Console’s default (factory-
installed) key assignments. Check with your Communications
Manager to see if your console assignments differ from the defaults.
110-Button DSS Console Default Assignments
80000 - 66

300 301 302 303 304 305 306 307 308 309

310 311 312 313 314 315 316 317 318 319

320 321 322 323 324 325 326 327 328 329

330 331 332 333 334 335 336 337 338 339

340 341 342 343 344 345 346 347 348 349

350 351 352 353 354 355 356 357 358 359

360 361 362 363 364 365 366 367 368 369

370 371 372 373 374 375 376 377 378 379

These keys are PAGE 1 PAGE 2 PAGE 3

PAGE
ALL
undefined
PARK 0 PARK 1 PARK 2 PARK 3 PARK 4 PARK 5 PARK 6 PARK 7 PARK 8 NIGHT

Note: DS1000 has Hotline keys

only for extensions 300-325.

62
80000mfh08-01.qxd 12/10/04 3:20 PM Page 63

Direct Station Selection Console

24-Button DSS Console Default Assignments

80000 - 25
300 312

301 313

302 314

303 315

304 316

305 317

306 318

307 319

308 320

309 321

310 322

311 323

63
80000mfh08-01.qxd 12/10/04 3:20 PM Page 64

Direct Station Selection Console

– For Your Notes –

64
80000mfh08-01.qxd 12/10/04 3:20 PM Page 65

Directed Call Pickup

Answer a co-worker’s
Directed Call Pickup permits you
calls from your phone. to pick up (intercept) a call ring-
ing a co-worker’s extension.

You can use Directed Call Pickup to pick up the following types
of calls ringing a co-worker’s phone:
● An outside line ringing a line key
● A co-worker’s Direct Inward Line
● A transferred outside call
● A ringing Intercom call
● A recall (such as a Hold or Transfer recall)

To use Directed Call Pickup to intercept a call to a co-

worker’s extension:

1. Press .

2. Dial .
3. Dial your co-worker’s extension number.
To intercept a call ringing an attendant, dial the
attendant’s extension number (e.g., 300). Do not dial
0 or 01-04.

65
80000mfh08-01.qxd 12/10/04 3:20 PM Page 66

Directory Dialing
Place Intercom or Speed
Dial calls from a Directory Dialing allows you to
select a co-worker or outside call
displayed list of names. from a list of names, rather than
dialing the phone number. (You
must have a display telephone to use Directory Dialing.) There are
three types of Directory Dialing:
C (2) System (Company-wide) Speed Dial names
I (4) Intercom names (including group names)
P (7) Personal Speed Dial names

To place a call using Directory Dialing:

1. Do not lift handset or press .

2. Dial (D) or DIRECTORY (DIR) .

3. If you dialed in the previous step:

Dial the Directory Dialing type.
C (2) System (Company-wide) Speed Dial names
I (4) Intercom names
P (7) Personal Speed Dial names
If you pressed DIRECTORY (DIR) in the previous step:
Select the Directory Dialing type.
COMPANY (CMPY) = System (company) Speed Dial
names
EXTENSION (EXT) = Intercom names
PERSONAL (PERS) = Personal Speed Dial names

66
80000mfh08-01.qxd 12/10/04 3:20 PM Page 67

Directory Dialing
4. Dial the number that corresponds to the first letter of the
desired name.
For example, dial 4 if the first letter begins with
G, H or I.
OR

Press or to scroll alphabetically through

the selected directory.
If you see the name you want to call, just press
DIAL to place your call.
5. Look at your phone’s display and dial the digit for the
letter you want to call.
Dial 1 for the first letter, 2 for the second letter, 3
for the third letter, and 4 for the fourth letter.
For example, if the name in step 4 above begins
with G, dial 1. If you see the name you want to call,
just press DIAL to place your call.

6. Press to scroll through all the names that

begin with the letter you selected.

7. Press to have the system dial your call.

67
80000mfh08-01.qxd 12/10/04 3:20 PM Page 68

Distinctive Ringing

Customize your
Use Distinctive Ringing to cus-
telephone’s ringing so tomize the way your telephone
you’ll know when calls rings. If you are in a large work
area with other co-workers, set up
are just for you. Distinctive Ringing so you’ll
always know when calls are for
you. In addition, Distinctive Ringing helps you more easily differen-
tiate the types of calls ringing your phone. Distinctive Ringing pro-
vides the following:
Distinctive Ring Configuration
Use Distinctive Ring Configuration to customize the ringing for your
telephone. There are 6 types of ringing at your phone (called a Ring
Set) that you can separately adjust:
– Intercom ringing
Includes ringing Intercom calls, as well as calls ringing Extension
Hunting Groups, Call Coverage keys and the operator’s Call key.
– Ring Group ringing
– Recall ringing
Includes Hold, Park and Transfer recall ringing.
– Type A ringing
Includes line key, loop key, Transfer and DIL ringing. (You
can reassign types A, B, and C ringing in Extension Override
and Key Ring Override below.)
– Type B ringing
Not used (unassigned) by default. (You can reassign types A, B,
and C in Extension Override and Key Ring Override below.)
– Type C ringing
Not used (unassigned) by default. (You can reassign types A, B,
and C in Extension Override and Key Ring Override below.)
Extension Override
If you want your outside calls to ring differently during the day, at
night, or after a delay, use Extension Override. You can use

68
80000mfh08-01.qxd 12/10/04 3:20 PM Page 69

Distinctive Ringing
Extension Override instead of Distinctive Ring Configuration if
you just want to change the way your outside calls ring. Or, you
can first set up Distinctive Ring Configuration and then use
Extension Override to further customize ringing. (Note that your
Extension Override selections always override your Distinctive
Ring Configuration settings.)
Key Ring Override
To have unique ringing just for your line, Call Coverage, and Group
Call Pickup keys, use Key Ring Override. You can use Key Ring
Override instead of either Extension Override or Distinctive Ring
Configuration, or in combination with both. (Note that your Key
Ring Override selections always override your Extension Override
or Distinctive Ring Configuration settings).
Distinctive Ring Administration (Admin)
Admin allows you to select a default Ring Set for your phone.
This is a quick way to change the way your phone rings. Here’s
how this works:
– The system has 3 Ring Sets (Set 1, Set 2 and Set 3).
– The 6 types of ringing within each of the 3 sets sound different.
– By default, your extension uses Set 1.
– Use Admin to select one of the other Ring Sets (2 or 3) for
your phone.
If you have a Super Display telephone, Admin lets you save your
Distinctive Ring Configuration settings as one of the system default
Ring Sets. Your settings then become a standard set that other users
can select.

Distinctive Ring Configuration

☎ Change the Ringing at your Extension
To customize ringing at your 22-button or 34-button dis-
play telephone:
– Your extension’s Class of Service may block you from
doing this. Ask your Communications Manager.

69
80000mfh08-01.qxd 12/10/04 3:20 PM Page 70

Distinctive Ringing

1. While idle, press PGM + MORE . You see:

2. Press RING . You see:

3. Press CNFG . You see:

– Press ICM to change the sound of your Intercom

ringing. (To make your Intercom calls ring, use the
#VA User-Programmable Feature.)
– Press RGRP to change the Ring Group ringing.
– Press RCL to change the sound of your Hold,
Park, and Transfer Recall ringing.
If you press MORE , you see:

– Press “A” , “B” , or “C” to change the sound of the

Type A, B or C ringing, respectively. You’ll use Type
A, B and C ringing when setting up Extension
Override (page 74) and Key Ring Override (page 78).
If you press MORE again, you see:

70
80000mfh08-01.qxd 12/10/04 3:20 PM Page 71

Distinctive Ringing

– Press DFLT to select one of the 3 default ringing

setups (1-3) and cancel your custom settings.
4. When you select a ringing option in the previous step,
your phone “plays” the current ring setting for that
option and displays your choice.
– For example, if you press ICM to change Intercom
ringing, you see:

For the option you choose to change:

– Press TONE to change the ringing pitch, then go to
step 5.
– Press CDNC to change the ringing pattern (or
cadence), then go to step 5.
– Press CNCL to cancel your selection and return to the
previous step.
– Press SAVE to save your changes (if you went to
step 5 and made any changes).
– Press to exit.
5. After pressing TONE or CDNC in the previous step, to
change the ringing pitch or pattern :

– Dial 0-9 to select a new ring pitch or pattern. You’ll hear

the pitch or pattern change after making your selection.
– Press CNCL to cancel and return to the previous step.
– Press OK to accept and return to the previous step.

71
80000mfh08-01.qxd 12/10/04 3:20 PM Page 72

Distinctive Ringing
To customize ringing at your super display telephone:
– Your extension’s Class of Service may block you from
doing this. Ask your Communications Manager.

1. While your phone is idle, press PROGRAM . You see:

2. Press RING . You see:

3. Press CONFIG . You see:

72
80000mfh08-01.qxd 12/10/04 3:20 PM Page 73

Distinctive Ringing

From the displayed choices:

– Press INTERCOM to change the sound of your
Intercom ringing. (To make your Intercom calls ring,
use the #VA User-Programmable Feature.)
– Press RING GROUP to change your Ring Group ringing.
– Press RECALL to change the sound of your Hold,
Park, and Transfer Recall ringing.
– Press RING “A” , RING “B” , or RING “C” to change
the sound of the Type A, B or C ringing. You’ll use Type
A, B and C ringing when setting up Extension Override
(page 74) and Key Ring Override (page 78).
– Press DEFAULT to select one of the 3 default ringing
setups (1-3) and cancel your custom settings.
4. When you select a ringing option in the previous step,
your phone “plays” the setting and displays your choice.
– For example, if you press INTERCOM to change
Intercom ringing, you see:

73
80000mfh08-01.qxd 12/10/04 3:20 PM Page 74

Distinctive Ringing
For the option you choose to change:
– Press RING TONE to change the ringing pitch, then
go to step 5.
– Press CADENCE to change the ringing pattern, then
go to step 5.
– Press CANCEL to cancel your selection and return
to the previous step.
– Press SAVE to save your changes (if you went
to step 5 and made any changes).
– Press to exit.
5. After pressing RING TONE or CADENCE in the previ-
ous step, To change the ringing pitch or pattern:

– Dial 0-9 to select a new ring pitch or pattern. You’ll hear

the pitch or pattern change after making your selection.
– Press CANCEL to cancel and return to the previous step.
– Press SAVE to accept and return to the previous step.

Extension Override
☎ Change the Ringing of your Outside Calls
To customize ringing for outside calls from your 22-button
or 34-button display telephone:
– Your extension’s Class of Service may block you from
doing this. Ask your Communications Manager.

74
80000mfh08-01.qxd 12/10/04 3:20 PM Page 75

Distinctive Ringing

1. While your phone is idle, press PGM . You see:

2. Press RING . You see:

3. Press ASGN to change the ringing for your outside

calls (Extension Override). You see:

4. Select the outside call ringing mode you want to change.

– Press DAY for day mode calls.
– Press NGT for night mode calls.
– Press DLY for delay ring calls.
You see (example shown if you select day ringing):

If you press MORE , you see:

– Select a ring type option ( “A” , “B” or “C” ), or

– Select LINE to have ringing follow the system default.
5. Press to hang up.
75
80000mfh08-01.qxd 12/10/04 3:20 PM Page 76

Distinctive Ringing
To customize ringing for outside calls from your super
display telephone:
– Your extension’s Class of Service may block you from
doing this. Ask your Communications Manager.

1. While your phone is idle, press PROGRAM . You see:

2. Press RING . You see:

76
80000mfh08-01.qxd 12/10/04 3:20 PM Page 77

Distinctive Ringing
3. Press ASSIGN to change the ringing for your out-
side calls (Extension Override). You see:

4. Select the outside call ringing mode you want to change.

– Press DAY RING for day mode calls.
– Press NIGHT RING for night mode calls.
– Press DELAY RING for delay ring calls.
You see (example shown if you select day ringing):

– Select a ring type option (Press RING “A” ,

RING “B” or RING “C” , or
– Press CO LINE to have ringing follow the system default.

5. Press to hang up.

77
80000mfh08-01.qxd 12/10/04 3:20 PM Page 78

Distinctive Ringing
Key Ring Override
☎ Set up Unique Ringing for your Line, Call
Coverage, and Group Call Pickup Keys.
To set up Key Ring Override for your 22-button or 34-but-
ton display telephone:
– Your extension’s Class of Service may block you from
doing this. Ask your Communications Manager.

1. While your phone is idle, press PGM . You see:

2. Press RING . You see:

3. To set up Key Ring Override, press KEY . You see:

4. Select the type of key you want to program.

– The ring type you select in the next step will be
assigned to the key you press in this step.
– After you make your selection, the keys of the chosen
type will illuminate.

78
80000mfh08-01.qxd 12/10/04 3:20 PM Page 79

Distinctive Ringing
5. Press one key of the type you selected above. You see
(example for Line Key 01 shown below):

– Dial to select Ring Type A.

– Dial to select Ring Type B.

– Dial to select Ring Type C.

– Dial select Standard (i.e., normal ringing for this

type of call).
6. Press another key to program it, or exit.

To set up Key Ring Override for your super display telephone:

– Your extension’s Class of Service may block you from
doing this. Ask your Communications Manager.

1. While your phone is idle, press PROGRAM . You see:

79
80000mfh08-01.qxd 12/10/04 3:20 PM Page 80

Distinctive Ringing

2. Press RING . You see:

3. To set up Key Ring Override, press KEY . You see:

4. Select the type of key you want to program.

– The ring type you select in the next step will be
assigned to the key you press in this step.
– After you make your selection, the keys of the chosen
type will illuminate.

80
80000mfh08-01.qxd 12/10/04 3:20 PM Page 81

Distinctive Ringing
5. Press one key of the type you selected above. You see
(example for Line Key 01 shown below):

– Dial to select Ring Type A.

– Dial to select Ring Type B.

– Dial to select Ring Type C.

– Dial select Standard (i.e., normal ringing for this

type of call).
6. Press another key to program it, or exit.

81
80000mfh08-01.qxd 12/10/04 3:20 PM Page 82

Distinctive Ringing
Administration
☎ Selecting and Storing a Default Ring Tone Set
To select a new default Ring Tone Set for your 22-button
or 34-button display telephone:

1. While your phone is idle, press PGM . You see:

2. Press RING . You see:

3. Press CNFG . You see:

4. Press MORE twice. You see:

5. Press DFLT . You see:

6. Select the Ring Tone Set you want to use (1-3).

– By default, your extension initially uses Ring Set 1.

82
80000mfh08-01.qxd 12/10/04 3:20 PM Page 83

Distinctive Ringing
7. When you see:

– Dial 9 (for yes) or confirm your selection, or

– Dial 6 (for no) to exit without making a selection.
8. Press to exit.

To select a new default Ring Tone Set for your super dis-
play telephone:

1. While your phone is idle, press PROGRAM . You see:

83
80000mfh08-01.qxd 12/10/04 3:20 PM Page 84

Distinctive Ringing
2. Press RING . You see:

3. Press CONFIG . You see:

3. Press DEFAULT . You see:

4. Select the Ring Tone Set you want to use (1-3).

– By default, your extension initially uses Ring Set 1.

84
80000mfh08-01.qxd 12/10/04 3:20 PM Page 85

Distinctive Ringing
5. When you see:

– Dial 9 (for yes) or confirm your selection, or

– Dial 6 (for no) to exit without making a selection.
7. Press to exit.

To store your customized ringing as a default Ring Tone

Set from your Super Display telephone:
– This option is only available at Super Display telephones.

1. While your phone is idle, press PROGRAM +

RING + CONFIG + DEFAULT . You see:

85
80000mfh08-01.qxd 12/10/04 3:20 PM Page 86

Distinctive Ringing

2. Press ADMIN . You see:

3. Enter the System Administrator (0000), System

Administrator 2 (9999), or Installer (372000) password.
You see:

4. Enter the number of the default Ring Set (1-3) to which

you want to save your phone’s configuration.

86
80000mfh08-01.qxd 12/10/04 3:20 PM Page 87

Distinctive Ringing
5. When you see:

– Dial 9 (for yes) to confirm your selection, or

– Dial 6 (for no) to exit without making a selection.
6. Press to exit.

87
80000mfh08-01.qxd 12/10/04 3:20 PM Page 88

Do Not Disturb
Work by your phone
Use Do Not Disturb (DND) to
undisturbed by incoming
block incoming calls, Off-Hook
calls and announcements. Signaling and Paging announce-
ments. With DND activated,
incoming calls will still flash your line keys — and you can use
your phone in the normal manner for placing and processing calls.

Do Not Disturb provides the following 4 DND options:

1 Incoming Outside Calls Blocked
This includes incoming outside calls, off-hook ringing, Call
Coverage and Group Call Pickup Key ringing, transferred
outside calls, and recalls.
2 Incoming Intercom Calls Blocked
This includes Intercom calls, transferred calls, and Paging
announcements.
3 All Incoming Calls Blocked
This includes all calls blocked by options 1 and 2.
0 Cancel Do Not Disturb
Notes:
● If you have a Direct Inward Line (DIL) on your phone, acti-
vating DND will put your DIL into the Night Mode.
● Call Forwarding has priority over Do Not Disturb. If you
enable both simultaneously, Call Forwarding is in force.

Do Not Disturb at your 22-Button or 34-Button

Telephone
To enable or disable DND:

1. Do not lift the handset or press .

2. Press . You see:

88
80000mfh08-01.qxd 12/10/04 3:20 PM Page 89

Do Not Disturb

The first line of the display shows the currently

selected DND type.
3. Select the soft key for the DND type you want to select.
OR
Dial a digit (0-3) for the DND type you want to select.
1 (or EXT ) = Incoming outside calls blocked
2 (or ICM ) = Incoming Intercom calls blocked
3 (or ALL ) = All calls blocked
0 (or OFF ) = Cancels DND.
If you are on a call (or anytime your phone is not
idle), pressing DND automatically enables DND for
all calls (type 3). If DND is enabled, pressing DND
automatically disables DND.
When DND types 2 or 3 are enabled, Intercom
callers hear DND tone and see “DO NOT DIS-
TURB” in their telephone’s display.
If you don’t make an entry for 10 seconds:
- If DND is disabled, the system automatically
enables DND All Calls.
- If DND is enabled, the system automatically can-
cels DND.

Do Not Disturb at your Super Display Telephone

To enable or disable DND:

1. Do not lift the handset or press .

2. Press . You see:

89
80000mfh08-01.qxd 12/10/04 3:20 PM Page 90

Do Not Disturb

The first line of the display shows the currently

selected DND type.
3. Select the soft key for the DND type you want to select.
OR
Dial a digit (0-3) for the DND type you want to select.
0 (or OFF ) = Cancels DND.
1 (or EXTERNAL ) = Incoming outside calls blocked
2 (or INTERCOM ) = Incoming Intercom calls blocked
3 (or ALL ) = All calls blocked
If you are on a call (or anytime your phone is not
idle), pressing DND automatically enables DND for
all calls (type 3). If DND is enabled, pressing DND
automatically disables DND.
When DND types 2 or 3 are enabled, Intercom
callers hear DND tone and see “DO NOT DIS-
TURB” in their telephone’s display.
If you don’t make an entry for 10 seconds:
- If DND is disabled, the system automatically
enables DND All Calls.
- If DND is enabled, the system automatically can-
cels DND.

90
80000mfh08-01.qxd 12/10/04 3:20 PM Page 91

Do Not Disturb
To check your extension’s DND type:
1. Look at the second line of your display. When you
enable Do Not Disturb, the display will show one of the
following:
DND ALL
DND EXTERNAL
DND INTERCOM

91
80000mfh08-01.qxd 12/10/04 3:20 PM Page 92

Do Not Disturb Override

Get through right away to

Do Not Disturb Override allows
a co-worker in Do Not you to override another exten-
Disturb. sion’s Do Not Disturb. You can
get through to a co-worker right
away while their phone is in Do
Not Disturb. To use this option, you must have DND Override
enabled in your Class of Service or be a Hotline partner for your
co-worker. Check with your Communications Manager.
To use Do Not Disturb Override:
1. Dial your co-worker.
2. When you hear DND tone and see DO NOT DISTURB
in your telephone’s display:
– Press OVRD ( DND OVERRIDE at Super Display).
OR

– Dial .
3. The system automatically places a ringing Intercom call
to your co-worker.
If you hear busy or ring/busy tone after step 2,
your co-worker is busy on a call.

92
80000mfh08-01.qxd 12/10/04 3:20 PM Page 93

Door Box
Use a Door Box to
The Door Box is a self-contained
remotely monitor an
Intercom unit you can use to mon-
entrance door. itor an entrance door. A visitor at
your door can press the Door Box
call button (like a door bell). The Door Box then sends chimes to
all telephones programmed to receive chimes. If the Door Box
chimes ring your phone, you can talk to the visitor at the door just
by lifting the handset.

The Door Box is convenient to have at a delivery entrance, for

example. You don’t need to have a co-worker monitor the deliv-
ery entrance; just answer the Door Box chimes instead.

If your telephone receives Door Box chimes, you may also be

able to remotely open and close the entrance door. Ask your
Communications Manager if you have this set up. If you do, after
answering the Door Box chimes you just press your FLASH key
or a soft key to open the door.
To place a call to the Door Box:

1. Press .
2. Dial the Door Box extension number.

To answer the Door Box chimes (i.e., to answer a call from

the Door Box):

1. Lift handset or press .

If you are an attendant, you’ll need a Call
Coverage key for the Door Box Ring Group to be
able to answer Door Box calls. Check with your
Communications Manager.
If you hear Door Box chimes over the Paging
speakers, you may be able to dial *0 to answer the
Door Box.

93
80000mfh08-01.qxd 12/10/04 3:20 PM Page 94

Door Box
To remotely open or close your entrance door:

1. To open the door, press or OPEN .

OR

To close the door, press again or CLOSE .

To place a call from the Door Box:

1. Press the Door Box call button.
2. When someone inside the building answers your call,
speak toward the Door Box.

94
80000mfh08-01.qxd 12/10/04 3:20 PM Page 95

Extension Locking

Secure your phone when

Use Extension Locking to secure
you must leave your desk. your phone when you leave your
office. You may want to do this if
your phone has Toll Restriction and Class of Service options
enabled that could be easily abused. While locked, the restric-
tions set up in Class of Service 15 and Toll Level 7 are in
force at your extension. When you return, just unlock your
extension to return it to normal operation. Ask your
Communications Manager for more about Extension Locking.

Locking and Unlocking Your Extension

To lock your extension:

1. Press and dial .

Your DND key winks on while your extension is
locked. In addition, you hear pulsating Intercom dial
tone when you press ICM.

To unlock your extension:

1. Press .
You hear pulsating Intercom dial tone.

2. Dial .
At a 22- or 34- Button Display telephone, you see:

At a Super Display Telephone, you see:

95
80000mfh08-01.qxd 12/10/04 3:20 PM Page 96

Extension Locking

3. Enter your PIN number + .

When entering your PIN number:
– CLEAR erases your entire entry.
– LND backspaces over (erases) the last digit
entered.

Entering or Changing Your PIN Number

To enter your PIN number (if you don’t have one assigned
to your extension):

1. Press .

2. Dial .
At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

96
80000mfh08-01.qxd 12/10/04 3:20 PM Page 97

Extension Locking

3. Enter your new PIN number + .

At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

4. To confirm your entry, reenter the PIN number you just

entered in step 3 above + HOLD.
At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

97
80000mfh08-01.qxd 12/10/04 3:20 PM Page 98

Extension Locking

5. Press EXIT .

To change your PIN number (if you already have one

assigned):

1. Press .

2. Dial .
At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

3. Enter your current PIN number + HOLD.

At a 22- or 34-Button Display Telephone, you see:

98
80000mfh08-01.qxd 12/10/04 3:20 PM Page 99

Extension Locking

At a Super Display Telephone, you see:

4. Enter your new PIN number + .

At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

5. To confirm your entry, reenter the PIN number you just

entered in step 4 above + HOLD.
At a 22- or 34-Button Display Telephone, you see:

99
80000mfh08-01.qxd 12/10/04 3:20 PM Page 100

Extension Locking

At a Super Display Telephone, you see:

6. Press EXIT .

To unlock an extension (and clear their PIN number) from

the attendant’s phone:

1. Press .
You must have a PIN number entered for your
phone to be able to use this feature.

2. Dial .
At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

100
80000mfh08-01.qxd 12/10/04 3:20 PM Page 101

Extension Locking

3. Enter your current PIN number + .

At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

4. Enter the number of the extension you want to unlock +

HOLD.
At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

101
80000mfh08-01.qxd 12/10/04 3:20 PM Page 102

Extension Locking

5. Press YES to unlock the extension entered in step 4

above.
OR
Press NO to go back to step 3 without unlocking.
6. When you have unlocked all extensions desired, press
CONF to exit.

102
80000mfh08-01.qxd 12/10/04 3:20 PM Page 103

Extension Hunting

Your system can Your phone may be in a group

with co-workers that share
automatically route calls
responsibility for answering calls.
to co-workers that work Each call into the group cycles
closely together. through the group until you or one
of your co-workers picks it up.
There are three types of hunting:
● Circular Hunting
With this type of hunting, a call unanswered at one member’s
extension rings the next extension in the list. If still unan-
swered, the call will continue to cycle through the group until
all members are rung.
● Terminal Hunting
In Terminal Hunting, a call unanswered by one member rings
the next extension in the list. Unlike Circular Hunting, how-
ever, the call will not cycle back to the top of the list. It rings
from the point at which it entered the list — and stops at the
last extension.
● Uniform Call Distribution (UCD) Hunting
With UCD, the system routes calls according to the frequency
of use of the member extensions. The first extension rung is
the member that has been idle the longest. The last extension
rung is the extension that has been idle the shortest. If you are
part of a Call Center, you may be in a UCD hunting group.

To temporarily install or remove your extension from your

UCD Group:

1. Press and dial , then

2. Dial to return your extension to your group, or

Dial to remove your extension from your group.

103
80000mfh08-01.qxd 12/10/04 3:20 PM Page 104

Flash

Make a new call without

While on a call, Flash lets you get
losing your line, or access dial tone for a new call without
unique features from your losing your line. You may also be
able to use Flash to access unique
phone company. features on your outside lines.
Check with your Communications
Manager to find out if your outside lines offer any unique features.
To Flash the line you are on:

1. Press .
After a brief interruption, you’ll hear dial tone for
a new call.
2. Dial your new call.
You may also be able to dial codes that let you
use unique features provided by your outside lines.

104
80000mfh08-01.qxd 12/10/04 3:20 PM Page 105

Forced Trunk Disconnect

Disconnect a co-worker’s
Forced Trunk Disconnect allows
outside call in an
you to disconnect (release) anoth-
emergency. er extension’s active outside call.
This is a powerful feature that
lets you access a busy line in an emergency — when no other
outside lines are available. Normally, Forced Trunk Disconnect is
reserved only for attendants and supervisors.
!! CAUTION !!
Forced Trunk Disconnect abruptly terminates the active call on
the outside line. Only use this feature in an emergency — when
no other outside lines are available.

To disconnect a busy outside line:

1. Press line key for busy outside line.
Line keys are red when busy.
OR

Press and dial the line’s Line Access Code (e.g.,

101 for line 1).

2. Dial to disconnect the line.

OR
Press MORE + DISC .
The line key goes out and you hear Intercom
dial tone.

To place a call after using Forced Trunk Disconnect:

You hear Intercom dial tone after step 2 above.
1. Hang up.
2. Press the line key and dial your number.

105
80000mfh08-01.qxd 12/10/04 3:20 PM Page 106

Group Call Pickup

Easily answer a call

You and some of your co-workers
ringing a Pickup Group, may be in a Pickup Group so you
even if you don’t know can easily answer each other’s
calls. If you hear a co-worker’s
which phone is ringing. phone ringing, for example, you
can intercept their call by dialing
a code or pressing your Group Call Pickup key. Ask your
Communications Manager if you are in a Pickup Group, and if
you have any Group Call Pickup keys.

Group Call Pickup can answer the following types of ringing calls:
● Intercom calls
● Transferred outside calls
● Direct Inward Lines
● Calls on lines assigned to the Pickup Group

To answer a call ringing a phone in your Pickup Group:

1. Lift handset.
2. Press flashing Group Pickup key.
OR

Dial .

User Programmable Feature

#RAP
Change the ringing mode of your Group Pickup keys.
See User Programmable Features at the end of this
guide for more.

106
80000mfh08-01.qxd 12/10/04 3:20 PM Page 107

Group Listen

Talk to an important client

Group Listen permits you to talk
or customer and have on the handset and have your
your co-worker’s listen in caller’s voice broadcast over your
telephone speaker. This lets others
on the meeting. in your work area listen to the
conversation. Group Listen turns
off your phone’s Handsfree microphone so the caller does not
hear your co-worker’s voices during a Group Listen.
To initiate Group Listen:
1. Place or answer call using the handset.

2. Press twice (but do not hang up).

SPK flashes slowly while Group Listen is active.
You can talk to the caller through your handset.
You and your co-workers hear your caller’s voice
over your phone’s speaker.
Your Handsfree microphone and handset receiver
are off.

To talk Handsfree after initiating Group Listen:

1. Press twice.
2. Hang up the handset.

To cancel Group Listen and return to your handset:

1. Do not hang up.

2. Press flashing .
You can talk to your caller over your handset. Your
co-workers can no longer hear your caller’s voice.

107
80000mfh08-01.qxd 12/10/04 3:20 PM Page 108

Group Ring

Calls can ring a group of If you are in a Ring Group with

co-workers simultaneously. some of your co-workers, all your
phones will ring simultaneously for
new calls into the group. Anyone in
the group can answer the Ring Group call just by lifting the handset.
The following types of calls can ring your Ring Group:
● Direct Inward Lines (DILs) into the Ring Group
● An outside call transferred into the Ring Group
● An Intercom call into your Ring Group

Check with your Communications Manager to find out if you are

in a Ring Group with some of your co-workers.

To answer a call ringing into your Ring Group:

1. Lift handset.

108
80000mfh08-01.qxd 12/10/04 3:20 PM Page 109

Handsfree

Talk over your phone

Handsfree
Handsfree, using the
Handsfree allows you to process
built-in speaker and calls using the speaker and micro-
microphone. phone in your telephone (instead
of the handset). Handsfree is a
— convenience when you don’t have
With Handsfree a free hand to pick up the handset
(for example, when you’re typing
Answerback, answer an on your computer).
intercom call by just
Handsfree Answerback
speaking toward your
Handsfree Answerback lets you
phone. answer a voice-announced
Intercom call by speaking toward
your phone (without lifting the handset). Like Handsfree, this is
also a convenience when you don’t have a free hand to pick up
the handset.
To activate Handsfree instead of lifting the handset:

1. Press .

To talk on a Handsfree call:

1. Speak toward your phone.
To temporarily turn off the Handsfree micro-
phone, see the Microphone Mute feature.

To hang up a Handsfree call:

1. Press .

109
80000mfh08-01.qxd 12/10/04 3:20 PM Page 110

Handsfree
To change a handset call into a Handsfree call:

1. Press .
2. Hang up the handset.

To change a Handsfree call into a handset call:

1. Lift handset.

User Programmable Feature

#VA
Enable voice-announce or ringing for your incoming
Intercom calls. See User Programmable Features at the
end of this guide for more.
Using Your Soft Keys
PGM + MORE + VANN
VAON Handsfree Answerback On
(Forced Intercom Ringing Off)
VAOFF Handsfree Answerback Off
(Forced Intercom Ringing On)

110
80000mfh08-01.qxd 12/10/04 3:20 PM Page 111

Handsfree
Automatic Handsfree
With Automatic Handsfree, you can place or answer a call
Handsfree just by pressing a key. You don’t have to press SPK
first. Use Automatic Handsfree when you don’t have a free hand
to answer a call or use a feature.

Automatic Handsfree is available for:

● Call Coverage and Hotline Keys
● Central Office Calls (line and loop keys)
● Dial Number Preview
● Directory Dialing
● Group Call Pickup Keys
● ICM key (Intercom)
● LND (Last Number Redial)
● Paging keys
● Park keys
● Personal Speed Dial bin keys
● Personal and System Speed Dial keys

111
80000mfh08-01.qxd 12/10/04 3:20 PM Page 112

Headset Compatibility
Have the privacy of a
handset call without having You can use a customer-provided
headset on your phone in place of
to hold the handset. the handset. Like using Handsfree,
the headset frees up your hands for
other work (like typing on your computer). In addition, the headset
provides privacy not available with Handsfree.

Ask your Communications Manager what types of headsets you

can use with your phone.
To enable the headset mode:
1. Unplug the telephone handset but leave it in the cradle.
2. Plug in the headset.
3. Press your Headset key.
Notes:
● You can have a Headset key on your telephone or your DSS
Console.
● The Headset key lights when your extension is in the Headset
mode, and is off while you have Headset mode disabled.
● If you are on a call, pressing the Headset key automatically
switches the active call to your headset. Pressing the Headset
key again switches the call back to Handsfree.
● While your extension is in the Headset mode, the system
ignores all hookswitch depressions.
When in the headset mode:
● Press a line key to place or answer an outside call.
OR

● Press to get Intercom dial tone.

OR

● If on a call, press to hang up.

112
80000mfh08-01.qxd 12/10/04 3:20 PM Page 113

Headset Compatibility
Headset Mode Feature Interactions
● Background Music
If programmed and connected, Background Music will broad-
cast over your telephone speaker while your extension is in the
Headset mode.
● Central Office Calls, Answering
While you are in the Headset mode, you can press your vol-
ume keys while idle to control the volume of any ringing call.
● Handsfree and Handsfree Answerback
Your extension in the Headset mode can receive normal voice-
announced Intercom calls. You can respond to the voice-
announced call by speaking toward your phone (just like non-
headset extensions). To answer the voice-announced call in the
headset, press SPK after hearing the voice-announcement.
● Microphone Mute
While on a headset call, you can press MIC to mute (i.e., turn
off) the headset microphone. While responding to an Intercom
call using Handsfree Answerback, pressing MIC mutes the
Handsfree microphone.
● Off-Hook Signaling for Outside Calls
Your extension in the headset mode can receive either Camp
On beeps or Off-Hook Ringing for incoming outside calls (just
like non-headset extensions).
● Off-Hook Signaling for Intercom Calls
Your extension in the headset mode can receive either Camp
On beeps or Voice Over announcements from a co-worker (just
like non-headset extensions).
● Off-Hook Signaling for Hotline Calls
Your extension in the headset mode can receive either Camp On
beeps or Voice Over announcements from their Hotline partner.
● Paging
Internal Paging announcements broadcast over your telephone
speaker while your extension is in the Headset mode.

113
80000mfh08-01.qxd 12/10/04 3:20 PM Page 114

Headset Compatibility
● Transfer
Screened and unscreened transfers work just like non-headset
extensions. For example, if you press SPK to answer a
screened transfer, the call will connect to your headset when
the transferring party hangs up.

Handsfree Transfers always connect to your headset, not

speakerphone.
● Volume Control
While on a headset call, you can press your volume keys to
adjust the receive volume in the headset.

User Programmable Feature

#HS
Enable or disable the headset mode at your phone. See
User Programmable Features at the end of this guide
for more.

114
80000mfh08-01.qxd 12/10/04 3:20 PM Page 115

Hold
Have a call wait on Hold,
Hold lets you put a call in a tem-
then pick it up to continue
porary waiting state. The caller on
the conversation. Hold hears silence or Music on
Hold, not the conversation in your
work area. While your call waits on Hold, you can process other
calls and use other features. Calls that you leave on Hold too long
will recall to you if you forget to pick them up.

There are four types of Hold:

● System (Regular) Hold
With System Hold, an outside call you place on Hold flashes
the line key at your co-workers’ phones. Any co-worker with
a flashing line key for the call can pick it up.
● Exclusive Hold
When you place a call on Exclusive Hold, only you can pick
up the call from Hold. The line flashes on your phone but
shows busy on your co-workers’ phones. Exclusive Hold is
important if you don’t want a co-worker picking up your
calls on Hold.
● Automatic Hold
Automatic Hold allows you to be on an outside call, activate
a feature and automatically place the call on Hold. You don’t
have to press the Hold key. The system places your call on
Hold when you press CONF, ICM, a Call Coverage key or a
Hotline key.
● Intercom Hold
You can also place an Intercom call on Hold. Your Intercom
call on Hold does not indicate on any other telephone.

115
80000mfh08-01.qxd 12/10/04 3:20 PM Page 116

Hold
To place an outside call on System Hold:

1. Press .
2. Hang up.
The line will recall with a distinctive “double-wink”
flash rate if you leave it on Hold too long.

To pick up an outside call on System Hold:

1. Press the flashing line key.

To pick up an outside call that a co-worker has placed on

System Hold (if you don’t have a line key for the call):

1. Press .

2. Dial followed by the line number (e.g., 01

for line 1).

To place an outside call on Exclusive Hold:

1. Press twice.

To pick up an outside call on Exclusive Hold:

1. Press the flashing line key.

To place an Intercom call on Hold:

1. Press .
2. Hang up.

To pick up a call on Intercom Hold:

1. Lift handset.
2. If you don’t hear Intercom dial tone, press .

3. Press .
116
80000mfh08-01.qxd 12/10/04 3:20 PM Page 117

Hold
Hold Recall
Your telephone display can show the type of call recalling, as well
as which co-worker initially placed the call on Hold.

Following are the displays you see at your phone when a call placed
on Hold is recalling. In the first example, the call was placed on Hold
at extension 301 (which does not have a name). In the second exam-
ple, the call was placed on Hold at extension 300 (which has the
name ATTENDANT).

117
80000mfh08-01.qxd 12/10/04 3:20 PM Page 118

Hotline
Take advantage of
one-button calling to a A Hotline key is a type of
Programmable Function Key that
co-worker with whom you gives you one-button calling and
work closely. Transfer to the co-worker assigned
as your Hotline partner. You can
have multiple Hotline keys on your phone, each set up for a differ-
ent Hotline partner. Your Hotlines function as DSS/BLF keys and
also show you the status of your partners’ extensions.

Hotline Key Flash Rates

When the key is: The covered extension is:
Off Idle or not installed
On Busy or ringing
Flashing Fast In Do Not Disturb for Intercom
calls (option 2) or all calls (option 3)
Wink Off In Do Not Disturb for
outside calls (option 1).

To place a call to your Hotline partner:

1. Press your Hotline key.
To Transfer your outside call to your Hotline partner:
1. While on the call, press your Hotline key.
2. Announce the call and hang up.
OR
Hang up to have the call wait at your Hotline partner
unannounced.
To answer a call from your Hotline partner:
1. Speak toward your phone.
User Programmable Feature
#HL
Change your Hotline key assignments. See User
Programmable Features at the end of this guide for more.

118
80000mfh08-01.qxd 12/10/04 3:20 PM Page 119

Idle Menu Soft Keys (Super Display)

Tailor your Super Display

If you have a Super Display
idle menu soft keys to Telephone, you can customize
meet your needs. your idle menu soft keys. The first
chart below shows the default idle
menu soft key assignments. The
chart on the next page shows all the available idle mode soft keys,
their definitions, and the related programming codes.
User Programmable Feature
# SM
Customize your Super Display telephone idle menu soft
keys. See User Programmable Features at the end of this
guide for more.

Super Display Telephone Default Idle Menu

Soft Key Assignments
Key Display Display Key

1 DIRECTORY (BLANK) 7
2 PROGRAM (BLANK) 8
3 V-MAIL -- (BLANK) 9
4 CALLS -- SP DIAL 1 10
5 PAGE SP DIAL 2 11
6 (BLANK) (BLANK) 12

119
80000mfh08-01.qxd 12/10/04 3:20 PM Page 120

Idle Menu Soft Keys (Super Display)

Super Display Telephone Idle Menu
Soft Key Options
Entry Display Description

00 UNDEFINED The key has no function and the idle menu display is blank.
01 DIRECTORY Press to access additional soft keys for Intercom, System Speed Dial,
and Personal Speed Dial Directory Dialing.
02 EXTENSION Press to directly access Intercom Directory Dialing.
03 PERSONAL Press to directly access Personal Speed Dial Directory Dialing.
04 COMPANY Press to directly access System Speed Dial Directory Dialing.
05 PROGRAM Press to program the following:
• Call Forwarding
• Call Screening
• Distinctive Ringing
• Handsfree Reply
• Intercom Voice Announce and Forced Intercom Ringing
• Language Selection
• Name Programming
• Speed Dial
• Volume for Ringing, Off-Hook Ringing, and Page
06 V-MAIL Press to call your Voice Mail mailbox. This soft key also shows the
number of new messages in your mailbox.
07 CALLS Press to review your Caller ID log. This soft key also shows the num-
ber of new calls you have not yet reviewed.
08 PAGE Press to initiate a Page announcement.
09 SP DIAL 1 Press to access Personal Speed Dial bins 701-710. The display shows
the Speed Dial numbers (or names - if programmed).
10 SP DIAL 2 Press to access Personal Speed Dial bins 711-720. The display shows
the Speed Dial number (or name - if programmed).
11-30 PERS SPDL BIN 1-20 Press to access the associated Personal Speed Dial bin (701-720).
The display shows the Speed Dial number (or name - if pro-
grammed).

120
80000mfh08-01.qxd 12/10/04 3:20 PM Page 121

Interactive Soft Keys

Use the advanced
Your display telephone has
features of your phone
Interactive Soft Keys that provide
just by pressing a soft intuitive feature access. You’ll
key, without remembering find it is no longer necessary to
remember feature codes to use the
feature codes. advanced features of your phone.
Instead, the function of your soft
keys change as you process calls.

When appropriate, this handbook provides the Interactive Soft

Key steps along with the codes for each feature. For additional
information on your soft keys, refer to the separately printed Soft
Key Glossary (P/N 80000GLO**).

121
80000mfh08-01.qxd 12/10/04 3:20 PM Page 122

Intercom

Call your co-workers on

Intercom gives you access to all
the Intercom. your co-workers and your sys-
tem’s attendants.
Handsfree Answerback
Handsfree Answerback lets you answer a voice-announced
Intercom call by speaking toward your phone (without lifting the
handset). Handsfree Answerback is also a convenience when you
don’t have a free hand to pick up the handset.
To place an Intercom call:

1. Lift handset and press .

2. Dial your co-worker’s extension number (e.g., 301).
To call your operator, dial the operator’s exten-
sion number, or dial or 01-04 (depending on how
your system is set up).
If your call voice-announces at your co-worker’s
extension, you can dial 1 to force the call to ring.

To answer an Intercom call (if you hear two beeps and your
phone has Handsfree Answerback):
1. Speak toward your phone.
OR
Lift your handset for privacy.

To answer an Intercom call (if you hear one beep and your
phone does not have Handsfree Answerback):
1. Lift the handset.

To answer an Intercom call (if you hear ringing):

1. Lift the handset.
If you hear ringing over the Paging speakers, you
may be able to dial *0 to pick up the call.

122
80000mfh08-01.qxd 12/10/04 3:20 PM Page 123

Intercom
User Programmable Feature
#VA
Enable voice-announce or ringing for your incoming
Intercom calls. See User Programmable Features at the end
of this guide for more.
Using Your Soft Keys
PGM + MORE + VANN
VAON Handsfree Answerback On
(Forced Intercom Ringing Off)
VAOFF Handsfree Answerback Off
(Forced Intercom Ringing On)

123
80000mfh08-01.qxd 12/10/04 3:20 PM Page 124

Language Selection
Change the language of
your telephone displays Use Language Selection to choose
English or Spanish as your tele-
and soft keys. phone’s display language. If you
choose Spanish, for example, your
feature status messages and soft keys will will change from
English to Spanish.
To change the display and soft key language at your
22-Button or 34-Button Telephone:
Your extension’s Class of Service may block you
from doing this. Ask your Communications Manager.
1. Press PGM + MORE + MORE + LANG .
The top line of the display shows the currently
selected language.
2. Press SPA to change the display language from
English to Spanish.
OR
Press ING to change the display language from
Spanish to English.
OR
Press EXIT or SAL to exit language programming
without changing your current selection.

124
80000mfh08-01.qxd 12/10/04 3:20 PM Page 125

Language Selection
To change the display and soft key language at your Super
Display Telephone:
Your extension’s Class of Service may block you
from doing this. Ask your Communications Manager.
1. Press PROGRAM + LANGUAGE .
The top line of the display shows the currently
selected language.
2. Press SPANISH to change the display language from
English to Spanish.
OR
Press INGLES to change the display language from
Spanish to English.
OR
Press EXIT or SALIR to exit language programming
without changing your current selection.

125
80000mfh08-01.qxd 12/10/04 3:20 PM Page 126

Last Number Redial

Quickly select and redial
Last Number Redial allows you to
the last outside number
quickly redial the last outside num-
you dialed. ber you dialed. Quickly recall a
busy or unanswered number with-
out manually dialing the digits. Last Number Redial saves in the
system memory the last 20 digits you dial, and can retain any com-
bination of digits 0-9, # and *. The system remembers the digits
regardless of whether the call was answered, unanswered or busy.
To redial your last call:
1. (Optional) Press an idle line key to preselect a line for
your call.

2. Press .

Enhanced Last Number Redial

If enabled for your display telephone, Enhanced Last Number
Redial allows you to select from the last 5 outside numbers dialed.
When you place an outside call, the number dialed is stored in the
Enhanced Last Number Redial buffer. This buffer saves the 5 most
recent numbers (including Speed Dial calls), with the most recent
call at the top of the buffer and the oldest number at the bottom of
the buffer. Old calls get pushed off the bottom of the buffer to make
room for new calls at the top. If you dial a number that is already
stored in the buffer, the system inserts the number at the top of the
buffer and deletes the duplicate entry.

The numbers stored in the Enhanced Last Number Redial buffer are
retained if the system resets or is powered down.

Ask your Communications Manager if you have Enhanced Last

Number Redial.

126
80000mfh08-01.qxd 12/10/04 3:20 PM Page 127

Last Number Redial

Enhanced Last Number Redial at your 22-Button or
34-Button Display Telephone
To redial your last call (when Enhanced Last Number Redial
is enabled):
Note: If you select a line key before going to step 1, the sys-
tem automatically outdials your most recent call when you
press LND.

1. Press . You see (for example):

The number to the right of the display shows the

Last Number Redial record number (1-5). To return
your phone to idle, press LND again.

2. (Optional) Press or to display the number

you want to recall.

3. Press , , or lift the handset to recall the dis-

played number.
The system tries to use the same line as that used
for your initial call.
– If that line is busy, the system selects a line from the
same group as your initial call.
– If all lines are busy, you can dial 2 to leave a Line
Queue or Line Camp On. The number will automati-
cally redial when the Line Queue or Line Camp On
goes through.

127
80000mfh08-01.qxd 12/10/04 3:20 PM Page 128

Last Number Redial

To erase (clear) all the numbers from your Enhanced Last
Number Redial buffer:

1. Press . You see (for example):

2. Press . You see:

3. Press YES to erase all the numbers in the Last

Number Redial buffer and return to idle.
OR
Press NO to return to step 1 without erasing the buffer.

128
80000mfh08-01.qxd 12/10/04 3:20 PM Page 129

Last Number Redial

Enhanced Last Number Redial at your Super Display
Telephone
To redial your last call (when Enhanced Last Number Redial
is enabled):
Note: If you select a line key before going to step 1, the sys-
tem automatically outdials your most recent call when you
press LND.

1. Press . You see (for example):

To return your phone to idle, press LND again.

2. Press the soft key that corresponds to the number you
want to recall.
The system tries to use the same line as that used
for your initial call.
– If that line is busy, the system selects a line from the
same group as your initial call.
– If all lines are busy, you can dial 2 to leave a Line
Queue or Line Camp On. The number will automati-
cally redial when the Line Queue or Line Camp On
goes through.

129
80000mfh08-01.qxd 12/10/04 3:20 PM Page 130

Last Number Redial

To erase (clear) all the numbers from your Enhanced Last
Number Redial buffer:

1. Press . You see (for example):

2. Press . You see:

3. Press YES to erase all the numbers in the Last

Number Redial buffer and return to idle.
OR
Press NO to return to step 1 without erasing the buffer.

130
80000mfh08-01.qxd 12/10/04 3:20 PM Page 131

Meet-Me Conference
Set up a multiple-party
With Meet-Me Conference, you
telephone meeting with
can set up a telephone meeting
your co-workers. with some of your co-workers —
without leaving the office. Your
co-workers join the Conference by dialing a Meet-Me
Conference code.
To set up a Meet-Me Conference:

1. Press .

2. Dial .
OR
Press PAGE .
3. Dial a page zone number.
Your page zone numbers are 1-7 for zones 1-7
and 0 for All Call.
4. Announce the Meet-Me Conference code.
Meet-Me Conference codes are #11 and #12.
5. Do not hang up.

6. Press and dial the announced Meet-Me

Conference code.
OR
Press MT11 or MT12 .
MT11 corresponds to code #11. MT12 corre-
sponds to code #12.
You and your co-workers must join the
Conference within a specified interval. Check with
your Communications Manager to find out what this
interval is.

131
80000mfh08-01.qxd 12/10/04 3:20 PM Page 132

Meet-Me Conference
To join a Meet-Me Conference:
1. Listen for page announcing the Meet-Me Conference.

2. Lift handset and press .

3. Dial the announced Meet-Me Conference code.
Meet-Me Conference codes are #11 and #12.

132
80000mfh08-01.qxd 12/10/04 3:20 PM Page 133

Message Waiting

Leave a Message Waiting

You can leave a Message Waiting
request for a return call. indication at a busy or unanswered
co-worker’s phone requesting a
return call. You don’t have to keep calling your co-worker back,
hoping to find them available. The Message Waiting indication is a
flashing MW key on your co-worker’s phone. When your co-work-
er answers their Message Waiting, you’ll automatically get a call.

You can leave Messages Waiting at any number of extensions.

Also, any number of co-workers can leave Messages Waiting at
your phone.
To leave a Message Waiting:
1. Place Intercom call to your co-worker.
The co-worker you call can be unanswered, busy
or in Do Not Disturb.

2. Press or MSG .
3. Hang up.
MW starts flashing on your co-worker’s phone.

To answer a Message Waiting:

Your MW key must be flashing.

1. Press .

2. Press .
Normally, your MW key goes out. If it continues
to flash, you have additional Messages Waiting.
If the co-worker that left you the message doesn’t
answer, is busy, or is in DND, your Message
Waiting cancels.
If your co-worker doesn’t answer, press your MW
key to leave them a Message Waiting.

133
80000mfh08-01.qxd 12/10/04 3:20 PM Page 134

Message Waiting
To review your Messages Waiting and then select a mes-
sage for a return call:
1. Do not lift the handset.

2. Press .
The first message displays. Press MW repeatedly
to display additional Messages Waiting, if any.

3. Press when the extension you want to call displays.

4. Press .
If the co-worker that left you the message doesn’t
answer, is busy, or is in DND, your Message
Waiting cancels.
If your co-worker doesn’t answer, press your MW
key to leave them a Message Waiting.

134
80000mfh08-01.qxd 12/10/04 3:20 PM Page 135

Microphone Mute
Talk to a co-worker in your
Microphone Mute lets you turn
office without your caller
off your phone’s Handsfree or
hearing the conversation. handset microphone at any time.
Microphone Mute prevents your
callers from hearing conversations in your work area. You can use
Microphone Mute while you are busy on the phone, in DND, or
while a call is ringing. The microphone stays off until you turn it
back on.

If you place a voice-announced Intercom call to a co-worker

while their microphone is muted, you hear a single beep. (If their
microphone is not muted, you will hear two beeps.)
To activate Microphone Mute:

1. Press .
Your MIC key goes on.
You can do this any time while on the phone or
while your phone is idle.

To deactivate Microphone Mute:

1. Press .
Your MIC key goes off.

Using the Handsfree Reply Soft Key at your 22-

Button or 34-Button Display Telephone
You can press your HFRP soft key to turn off your telephone’s
Handsfree microphone for incoming Intercom calls.
To turn off your telephone’s microphone for Incoming
Intercom calls:
1. Press PGM + MORE . You see:

135
80000mfh08-01.qxd 12/10/04 3:20 PM Page 136

Microphone Mute

2. Press HFRP . You see:

The first line of the display indicates whether

Handsfree Reply is on or off.
3. To turn Handsfree Reply on (if it is off), press ON .
OR
To turn Handsfree Reply off (if it is on), press OFF .

When you answer a voice-announced Intercom call (if

Handsfree Reply is off):
You hear a single beep in your speaker and the
voice of the calling party. The ICM, MIC, and SPK
keys are on.
1. To answer the voice-announcement, lift the handset.
OR
Press to turn Handsfree Reply back on (for this
call only).

Using the Handsfree Reply Soft Key at your Super

Display Telephone
You can press your HF REPLY soft key to turn off your tele-
phone’s Handsfree microphone for incoming Intercom calls.
To turn off your telephone’s microphone for Incoming
Intercom calls:
1. Press PROGRAM . You see:

136
80000mfh08-01.qxd 12/10/04 3:20 PM Page 137

Microphone Mute

2. Press HF REPLY . You see:

The first line of the display indicates whether

Handsfree Reply is on or off.
3. To turn Handsfree Reply on (if it is off), press ON .
OR
To turn Handsfree Reply off (if it is on), press OFF .

When you answer a voice-announced Intercom call (if

Handsfree Reply is off):
You hear a single beep in your speaker and the
voice of the calling party. The ICM, MIC, and SPK
keys are on.
1. To answer the voice-announcement, lift the handset.
OR

Press to turn Handsfree Reply back on (for this

call only).

137
80000mfh08-01.qxd 12/10/04 3:20 PM Page 138

Monitor / Silent Monitor

Monitor a co-worker’s
Monitor lets you listen to the con-
conversation without
versation at a busy co-worker’s
them knowing you are on extension. Your busy co-worker
the phone. and their caller have no indication
that you are on the call. This fea-
ture could help you if you are a
service department supervisor, for example. You could listen to
the questions that your department’s callers ask without disturbing
the service call.

!! CAUTION !!
Monitor provides no warning tones prior to intrusion. Monitor
may be interpreted as an invasion of privacy.

To Monitor a call:
1. Call busy co-worker.

2. Dial or press MON .

3. Listen to the conversation in progress.
4. Hang up when you are done.

138
80000mfh08-01.qxd 12/10/04 3:20 PM Page 139

Name Programming

Program your extension’s You can customize your exten-

name from your telephone. sion’s name. When you place an
Intercom call, the name you enter
shows on your co-worker’s dis-
play. If you are an attendant, you may also be able to program a
co-worker’s name as well as the name for a ring Group or UCD
Hunting Group. Check with your Communications Manager.
To program your extension’s name:
1. At a 22- or 34-Button Display Telephone:
Press PGM + MORE + MORE + NAME .
At a Super Display Telephone:
Press PROGRAM + NAME .
2. Follow the instructions in the Name Programming chart
on the next page.

3. Press + to exit.
To program a name for a co-worker’s extension:
You must have Access Level 4 or 5 to do this.
1. At a 22- or 34-Button Display Telephone:
Press PGM + MORE + MORE + NAME .
At a Super Display Telephone:
Press PROGRAM + NAME .
2. When you see EXT:3xx, enter the number of the exten-
sion you want to program + HOLD.
You can optionally enter a Ring Group or UCD
Group master number to program the name of the
associated group.

139
80000mfh08-01.qxd 12/10/04 3:20 PM Page 140

Name Programming
3. Follow the instructions in the Name Programming chart
shown below.

4. Press + to exit.

Name Programming
Press a key the indicated number of times for desired character
Key 1 Time 2 Times 3 Times 4 Times 5 Times 6 Times 7 Times 8 Times 9 Times
1 & - / ‘ 1
2 A B C a b c 2
3 D E F d e f 3
4 G H I g h i 4
5 J K L j k l 5
6 M N O m n o 6
7 P Q R S p q r s 7
8 T U V t u v 8
9 W X Y Z w x y z 9
0 space : 0
# Not used

* Not used

After selecting a letter, press a key for another letter or wait 2 seconds for the cursor to automatically advance.
Additional Name Programming Options
HOLD Save name. In system programming, HOLD saves and exits name programming.
CONF Exit name programming without saving name.
VOL Up Scroll the cursor to the left.
VOL Dn Scroll the cursor to the right.
MW Put the cursor after the last entry.
LND Delete the character under the cursor.
FLASH Delete the character to the right of the cursor.
CLEAR Clear the entire entry.
CHECK Restore the previous entry,

140
80000mfh08-01.qxd 12/10/04 3:20 PM Page 141

Night Service / Night Ring

Night Service reroutes
your system’s calls after Night Service redirects your sys-
tem’s calls to their Night Mode
hours. destination. Typically, the atten-
dant or supervisor activates Night
Service after normal working hours, when most of your co-work-
ers are unavailable to answer calls. If you are expected to put the
system in the Night Mode, your phone will have a Night key.
Check with your Communications Manager.
To activate or deactivate Night Service:
1. Do not lift the handset.
2. Press your Night key.
Your Communications Manager can tell you if
you have a Night key, and which outside lines your
Night key switches.

141
80000mfh08-01.qxd 12/10/04 3:20 PM Page 142

Off-Hook Signaling
Off-Hook Signaling helps
While you are busy on a call,
important callers get
Off-Hook Signaling lets you know
through. when another caller is tying to get
through. Off-Hook Signaling
helps your important callers get through, without waiting in line
for you to become free. After you hear an Off-Hook Signal, you
can use another system feature to process your current call (such
as Hold or Park). You can then answer the waiting call.

You can receive Off-Hook Signals while you are busy on the
handset. There are two types of Off-Hook Signaling:
● Off-Hook Ringing
Off-Hook Ringing is muted ringing from your phone’s speaker.
Off-Hook Ringing occurs only for waiting outside calls.
● Camp-On Tones
Camp-On Tones are two beeps in your handset receiver.
Camp-On Tones can occur for both waiting Intercom and out-
side calls.
Also refer to the Voice Over feature.

To adjust the volume of Off-Hook Ringing:

1. Press or while you hear the muted ringing.

User Programmable Feature

#OHS
Change your Off Hook Signaling options. See User
Programmable Features at the end of this guide for more.

142
80000mfh08-01.qxd 12/10/04 3:20 PM Page 143

Paging
Use Paging to broadcast
announcements or Paging lets you broadcast
announcements to other keyset
quickly locate co-workers. users and to external Paging
speakers. Paging allows you to
locate a co-worker or make an announcement without calling each
extension individually. There are two types of Paging: Internal
Paging and External Paging.

Internal Paging
Internal Paging allows you to broadcast announcements into 7
internal Paging Zones and All Call (all zones). When you make a
zone page, your announcement simultaneously broadcasts to all
extensions in the specified zone. When you make an All Call
page, your announcement simultaneously broadcasts to extensions
in all zones. (Your system may limit the length of your Paging
broadcasts. Check with your Communications Manager.)

External Paging
When you page into Internal All Call Page or Internal Zone Page
1, the system simultaneously broadcasts the announcement into
the External Paging Zone. Typically, your system’s External
Paging Zone connects to speakers in your ceiling.

143
80000mfh08-01.qxd 12/10/04 3:20 PM Page 144

Paging
To make an Internal Paging Announcement:

1. Press .

2. Dial or press PAGE .

3. Dial the Page Zone number or press ALL (for All
Call Page).
Page zone numbers are 1-7 or 0 for All Call.
If you dial *10 or *11, your announcement broad-
casts into the External Paging Zone as well.
4. Make announcement and hang up.

User Programmable Feature

#VP
Enable or disable incoming Paging announcements. See
User Programmable Features at the end of this guide
for more.

144
80000mfh08-01.qxd 12/10/04 3:20 PM Page 145

Park
Park a call in orbit so a
co-worker can pick it up. Park places an outside call in a
waiting state (called a Park Orbit)
You don’t have to locate so a co-worker can pick it up.
a co-worker to handle There are two types of Park:
System and Personal. Use System
their calls. Park when you want to have your
call wait in one of 10 system
orbits (60-69). Personal Park allows you to park a call at an
extension so a co-worker can pick it up. After parking a call, you
can Page for the co-worker and hang up. Your co-worker then
dials a code to pick up their call.

If a call you Park is not retrieved, it will recall to you. Your

Communications Manager can tell you what the recall time is for
System Park orbits 60-67. The recall time for orbits 68 and 69 is
fixed at 5 minutes.

System Park
To Park a call in a System Park Orbit:

● Standard Operation

1. While on an outside call, press .

2. Dial and the System Park Orbit (60-69).

3. Hang up.

● Using Your Soft Keys

1. While on an outside call, press PARK .

2. Press SYS .
3. Dial the System Park Orbit (0-9) and hang up.

145
80000mfh08-01.qxd 12/10/04 3:20 PM Page 146

Park
To retrieve a call from a System Park Orbit:

● Standard Operation

1. Press .

2. Dial and the System Park Orbit (60-69).

● Using Your Soft Keys

1. Press and press PKUP .

2. Press SYS .
3. Dial the System Park Orbit (0-9) and hang up.

Personal Park
To Park a call at a co-worker’s extension (using Personal
Park):

● Standard Operation

1. While on an outside call, press .

2. Dial .
3. Dial the number of the extension at which you want to
Park the call.

146
80000mfh08-01.qxd 12/10/04 3:20 PM Page 147

Park
● Using Your Soft Keys

1. While on an outside call, press PARK .

2. Press PERS .
3. Dial a co-worker’s extension number and hang up.

To retrieve a call parked at a co-worker’s extension:

● Standard Operation

1. Press and dial .

2. Dial the number of the extension at which the call is
Parked.
● Using Your Soft Keys

1. Press and press PKUP .

2. Press PERS .
3. Dial the number of the extension at which the call is
Parked.

147
80000mfh08-01.qxd 12/10/04 3:20 PM Page 148

Park
Park Recall
Your telephone display can show the type of call recalling, as well
as which co-worker initially parked the call.

Following are the displays you see at your phone when a parked call
is recalling. In the first example, the call was parked in system orbit
60 by extension 301 (which does not have a name). In the second
example, the call was parked in system orbit 60 by extension 300
(which has the name ATTENDANT).

148
80000mfh08-01.qxd 12/10/04 3:20 PM Page 149

Prime Line Preference

Get dial tone for a call Prime Line Preference allows you
just by lifting the handset. to get dial tone for a call just by
lifting the handset. You do not have
to press a line key, loop key or the
ICM key first. You can have Prime Line Preference for Intercom
calls or outside lines (regardless of whether you have a line or loop
key for the outside line). Check with your Communications
Manager to find out if you have Prime Line Preference, and which
key on your phone (if any) is your Prime Line key.

Prime Line and Ringing Line Preference

Ringing Line Preference has priority over Prime Line. For example,
Ringing Line Preference will answer a ringing outside call, not give
you dial tone on your Prime Line. Also, a ringing Prime Line has pri-
ority over any other ringing line. The answer priority is as follows:
● Ringing Prime Line
● Ringing non-Prime Line
● Prime Line
To place a call on your Prime Line:
1. Lift the handset.
If you want to bypass your Prime Line, press a
line or loop key before lifting the handset.
2. Dial the call normally.

User Programmable Feature

#PLA
Change your Prime Line key assignment. See User
Programmable Features at the end of this guide for more.

149
80000mfh08-01.qxd 12/10/04 3:20 PM Page 150

Privacy and Privacy Release Groups

Privacy prevents
interruptions at your Privacy
If your extension has Privacy
extension. enabled, it automatically blocks
— incoming Barge In attempts and
Camp-On signals from your co-
Privacy Release lets you
workers. If you don’t want your
join co-worker’s calls. conversations interrupted, use
Privacy. Check with your
Communications Manager to find out if your extension has Privacy.

Note: If you’re on a call with a co-worker, your conversation can

still be interrupted by Barge In attempts and Camp-On signals
sent to your co-worker.

Privacy Release Groups

If you are in a Privacy Release Group with some of your
co-workers, you can easily join in each other’s outside calls. All
you have to do is press the busy line key for the call to join in.
Your Communications Manager can tell you if you are in a
Privacy Release Group.
To join an outside call with a member of your Privacy
Release Group:
1. Press the busy (red) line key.
The line key lights green when you connect.

To prevent a member of your Privacy Release Group from

joining your call:
1. Place or answer an outside call on a line key.
The line key lights orange.
2. Press the line key.
The line key lights green.
Repeat step 2 to allow a co-worker to join in.

150
80000mfh08-01.qxd 12/10/04 3:20 PM Page 151

Programmable Function Keys

Programmable Function
Your keyset has Programmable
Keys simplify your
Function Keys. These keys sim-
phone’s operation. plify placing calls, answering
calls, and using certain features.
Your Programmable Function Keys are assigned for you, but can
be changed as your needs change. Your Communications
Manager can tell you which Programmable Function Keys are
currently on your phone.

If you have a 22-Button Standard or

22-Button Display Telephone, you have 12
Programmable Function Keys.

If you have a 34-Button Display

Telephone, you have 24 Programmable
Function Keys.

If you have a 34-Button Super Display

Telephone, you also have 24 Programmable
Function Keys.

The following chart shows the available Programmable Function

Key functions, the key code required for programming the key,
and the Busy Lamp Field (BLF) flash rates for each key. The chart
also provides a brief guide on how to use the key.

151
80000mfh08-01.qxd 12/10/04 3:20 PM Page 152

Programmable Function Keys

Programmable Function Key Assignments

Account Code
Key Code: . . . . . . . . . . . . . . .26
BLF: . . . . . . . . . . . . . . . . . . .Off: Account Code inactive
On: Account Code active for call
Fast Flash: Account Code entry mode
Operation: . . . . . . . . . . . . . . .Press to enter Account Code, then
press again to return to call.
Call Coverage
Key Code: . . . . . . . . . . . . . . .Call Coverage Immediate Ring:
06 + Covered Extension (e.g., 304)
Call Coverage No Ring (lamp only):
07 + Covered Extension (e.g., 304)
Call Coverage Delay Ring:
08 + Covered Extension (e.g., 304)
BLF: . . . . . . . . . . . . . . . . . . .Off: Co-worker idle
On: Co-worker busy
Fast Flash: Co-worker in DND (2 or 3)
Wink Off: Co-worker in DND (1)
Operation: . . . . . . . . . . . . . . .Press to call co-worker or pick up ring-
ing call.
Call Forwarding
Key Code: . . . . . . . . . . . . . . .27
BLF: . . . . . . . . . . . . . . . . . . .Off: Call Forwarding disabled
Fast Flash: Extension in Call
Forwarding programming mode
Wink Off: Call Forwarding enabled
Operation: . . . . . . . . . . . . . . .While idle, enters Call Forward pro-
gramming mode. While busy, switches
Call Forwarding on and off.
Call Timer (Automatic or Manual)
Key Code: . . . . . . . . . . . . . . .16 + 1 [Manual Timer] or 2 [Auto Timer]
BLF: . . . . . . . . . . . . . . . . . . .Off: Call Timer off
On: Call Timer on
Operation . . . . . . . . . . . . . . .Press to start or stop Call Timer.
Conversation Record
Key Code: . . . . . . . . . . . . . . .17
BLF: . . . . . . . . . . . . . . . . . . .Off: Recording Off
On: Recording Being Set Up
Fast Flash: Recording On
Operation: . . . . . . . . . . . . . . .Press to record conversation in mailbox.

152
80000mfh08-01.qxd 12/10/04 3:20 PM Page 153

Programmable Function Keys

Programmable Function Key Assignments (Cont’d)

Group Pickup
Key Code: . . . . . . . . . . . . . . .Group Pickup Immediate Ring:
09 + Pickup Group (1-8)
Group Pickup No Ring (lamp only):
10 + Pickup Group (1-8)
Group Pickup Delay Ring:
11 + Pickup Group (1-8)
BLF: . . . . . . . . . . . . . . . . . . .Off: Call not ringing group
Slow Flash: Call ringing group
Operation: . . . . . . . . . . . . . . .Press key to answer call ringing Pickup
Group.
Headset Mode
Key Code: . . . . . . . . . . . . . . .28
BLF: . . . . . . . . . . . . . . . . . . .Off: Headset mode disabled
On: Headset mode enabled
Operation: . . . . . . . . . . . . . . .Press to enable/disable headset mode
Hotline
Key Code: . . . . . . . . . . . . . . .05 + Hotline Partner’s Ext. (e.g., 304)
BLF: . . . . . . . . . . . . . . . . . . .Off: Partner is idle
On: Partner is ringing or busy
Fast Flash: Partner in DND (2 or 3)
Wink Off: Partner in DND (1)
Operation: . . . . . . . . . . . . . . .Press to call Hotline partner.
Intercom Directory Dialing
Key Code: . . . . . . . . . . . . . . .21
BLF: . . . . . . . . . . . . . . . . . . .Off: Inactive
On: Active
Operation: . . . . . . . . . . . . . . .Press key to access Intercom Directory
Dialing.
Line Keys
Key Code: . . . . . . . . . . . . . . .03 + Line number (e.g., 1)
BLF: . . . . . . . . . . . . . . . . . . .Off: Line idle or not installed
On: Line busy
Slow Flash: Line ringing
Operation: . . . . . . . . . . . . . . .Press to place or answer call on out-
side line.

153
80000mfh08-01.qxd 12/10/04 3:20 PM Page 154

Programmable Function Keys

Programmable Function Key Assignments (Cont’d)

Loop Keys (Switched or Fixed)
Key Code: . . . . . . . . . . . . . . .Switched Loop Key: 01
Fixed Loop Key: 02 + Line group (90-98)
BLF: . . . . . . . . . . . . . . . . . . .Off: Loop key idle
Slow Flash (red): A call is ringing the
loop key
On (green): You are on a loop key call
Operation: . . . . . . . . . . . . . . .Press key to place or answer a call.
Message Center
Key Code: . . . . . . . . . . . . . . .24 + Message Center Extension
BLF: . . . . . . . . . . . . . . . . . . .Off: No messages in Message Center
Fast Flash: Messages are waiting in
Message Center
Operation: . . . . . . . . . . . . . . .Press to see how many messages are
waiting in Message Center.
OR
Press SPK + key to call Message
Center.
Night Key
Key Code: . . . . . . . . . . . . . . .18 + CLEAR
BLF: . . . . . . . . . . . . . . . . . . .Off: System in Day Mode
On: System in Night Mode
Operation: . . . . . . . . . . . . . . .Press to switch Day/Night mode of the
system.
Page Zones
Key Code: . . . . . . . . . . . . . . .13 + Page Zone (0 for All Call, zone 1-7)
BLF: . . . . . . . . . . . . . . . . . . .Off: Page Zone idle
On: Page Zone busy
Operation: . . . . . . . . . . . . . . .Press to Page into assigned zone.
Park Orbits
Key Code: . . . . . . . . . . . . . . .04 + Park Orbit (60-69)
BLF: . . . . . . . . . . . . . . . . . . .Off: Park Orbit idle
On: Has a call parked by a co-worker
Wink On: Has a call you parked
Operation: . . . . . . . . . . . . . . .Press to Park or retrieve call from orbit.

154
80000mfh08-01.qxd 12/10/04 3:20 PM Page 155

Programmable Function Keys

Programmable Function Key Assignments (Cont’d)

Reverse Voice Over
Key Code: . . . . . . . . . . . . . . .23+ Covered Extension (e.g., 304)
BLF: . . . . . . . . . . . . . . . . . . .Off: Co-worker idle
On: Co-worker busy or ringing
Fast Flash: Co-worker in DND
Operation: . . . . . . . . . . . . . . .While on handset call, press key to
place private Intercom call to co-worker.
Save
Key Code: . . . . . . . . . . . . . . .25
BLF: . . . . . . . . . . . . . . . . . . .No BLF
Operation: . . . . . . . . . . . . . . .While on a call, press key to Save
number you just dialed.
OR
While idle, press key to redial previous-
ly saved number.
Personal or System Speed Dial
Key Code: . . . . . . . . . . . . . . .System Speed Dial:
14 + System Bin (200-299)
Personal Speed Dial:
15 + Personal Bin (701-720)
BLF: . . . . . . . . . . . . . . . . . . .No BLF
Operation: . . . . . . . . . . . . . . .Press to dial stored number.
Split
Key Code: . . . . . . . . . . . . . . .20
BLF: . . . . . . . . . . . . . . . . . . .No BLF
Operation: . . . . . . . . . . . . . . .Press to switch between calls. See the
Split feature in this handbook for more.

Check Key
Use your CHECK key to quickly check your Programmable
Function Key and DSS Console Programmable Function Key
assignments. You can also use the CHECK key to display your
Personal Speed Dial names (if programmed).
To check a Programmable Function Key assignment:
1. Press .
SPK flashes while you are in the check mode.

155
80000mfh08-01.qxd 12/10/04 3:20 PM Page 156

Programmable Function Keys

2. Press the Programmable Function Key you want to
check.
3. Press another Programmable Function Key.
OR

Press to exit.

To check a Personal Speed Dial key:

1. Press .
SPK flashes while you are in the check mode.
2. Press the Personal Speed Dial key (1-10) once to display
the name for the lower numbered bin (e.g., 701).
3. Press the Personal Speed Dial key (1-10) a second time to
display the number stored in the lower numbered bin.
4. Press the Personal Speed Dial key (1-10) a third time to
display the name for the higher numbered bin (e.g., 711).
5. Press the Personal Speed Dial key (1-10) a fourth time to
display the number stored in the higher numbered bin.
6. Press another Personal Speed Dial Key.
OR

Press to exit.

User Programmable Feature

#KP
Change your Programmable Function Key assignments.
See User Programmable Features at the end of this guide
for more.

156
80000mfh08-01.qxd 12/10/04 3:20 PM Page 157

Removing Lines and Extensions

Temporarily remove
problem extensions and You can remove problem outside
lines and co-worker’s extensions
lines from service until from service. This helps ensure
they can be repaired. maximum system performance.
Normally, this capability is
reserved for attendants and supervisors. For example, the atten-
dant can busy-out a noisy line or faulty extension until service
personnel can repair the problem. The line or extension appears
busy to callers. Ask your Communications Manager if you can
use this feature.
To remove or return an extension or line to service:

1. Press and dial .

2. Dial the number of the extension you want to remove or
return to service (e.g., 300).
OR
Dial the number of the outside line you want to remove
or return to service (e.g., 101).

3. Dial to to return.
OR

Dial to remove.

4. Press to hang up.

157
80000mfh08-01.qxd 12/10/04 3:20 PM Page 158

Reverse Voice Over

Privately call a co-worker
while you’re busy on While on a handset call, Reverse
Voice Over lets you make a pri-
your handset. vate Intercom call to an idle
co-worker. You just press and
hold down your Reverse Voice Over key to make the private call.
Your initial caller cannot hear the Reverse Voice Over (private
Intercom) conversation. The private Intercom call continues until
you release your Reverse Voice Over key. Your initial call can be
an outside call or an Intercom call to a co-worker.

If you are a salesperson, for example, Reverse Voice Over can help
you while placing a call to an important client. You can talk to the
client and give special instructions to an assistant — all without
interrupting your initial client call.

You can have Reverse Voice Over keys for more than one
co-worker. Ask your Communications Manager if you have any
of these keys.

While your telephone is idle, your Reverse Voice Over key func-
tions the same as a Hotline key. (You cannot, however, use it to
Transfer calls.) The key shows at a glance the status of your co-
worker’s extension.

Reverse Voice Over Key Flash Rates

When the key is: The covered extension is:
Off Idle or not installed
On Busy or ringing
Flashing Fast In Do Not Disturb for Intercom
calls (option 2) or all calls (option 3)
Wink Off In Do Not Disturb for
outside calls (option 1)

158
80000mfh08-01.qxd 12/10/04 3:20 PM Page 159

Reverse Voice Over

To place a Reverse Voice Over call:
1. While on a handset call, press and hold your Reverse
Voice Over key.
You hear two beeps, then conversation with your
co-worker in your handset.
Your Voice Over key lights red.

To return to your initial caller:

1. Release your Reverse Voice Over key.
Conversation with your initial caller (in your
handset) continues.
Your Voice Over key goes out.

To place a call to the co-worker assigned to your Reverse

Voice Over key:
1. While your telephone is idle, press your Reverse Voice
Over key.
You hear two beeps, then conversation with your
co-worker.
Your Reverse Voice Over key goes on (green).

159
80000mfh08-01.qxd 12/10/04 3:20 PM Page 160

Ringing Line Preference

Simply lift the handset to

Ringing Line Preference lets you
answer a ringing call. answer a ringing call just by lift-
ing the handset. If you primarily
answer calls, Ringing Line Preference ensures that your incoming
calls have priority. Your Communications Manager can tell you if
you have Ringing Line Preference.

If you have multiple calls ringing your extension at the same

time, lifting the handset (with Ringing Line Preference) answers
the calls in the following order:
● key.
● Line key (lowest key first). For example, if lines 2 and 4 are
ringing, lifting the handset answers line 2 first.
● Loop key (lowest key first). For example, if keys 1 and 5 are
ringing, lifting the handset answers key 1 first.
In addition, if you and a co-worker with Ringing Line Preference
answer the same outside line at the same time, the system con-
nects the call to the lowest numbered extension.

Prime Line and Ringing Line Preference

Ringing Line Preference has priority over Prime Line. For exam-
ple, Ringing Line Preference will answer a ringing outside call,
not give you dial tone on your Prime Line.

160
80000mfh08-01.qxd 12/10/04 3:20 PM Page 161

Ringing Line Preference

To use Ringing Line Preference:

1. Lift the handset or press .

You automatically answer the call.

To bypass Ringing Line Preference:

1. Before lifting the handset or pressing , press one of

the following:

-
- Line key
- Programmable Function Key

User Programmable Feature

#RLP
Enable or disable Ringing Line Preference. See User
Programmable Features at the end of this guide for more.

161
80000mfh08-01.qxd 12/10/04 3:20 PM Page 162

Save Number Dialed

Save the number you just Save Number Dialed permits you
dialed for quick redialing. to save your last outside number
and easily redial it later on. For
example, you can recall a busy or
unanswered number without manually dialing the digits. Your
phone system retains the saved number until you store a new one
in its place.

Save Number Dialed saves in system memory a number you dial

up to 20 digits. The system remembers the number regardless of
whether the call was answered, unanswered or busy.

Unless your phone has a display, you must have a uniquely pro-
grammed Save Number Dialed Programmable Function Key to
use this feature. Check with your Communications Manager to
find out if you have this key.
To save the outside number you just dialed:
1. Press SAVE or your Save Number Dialed key.
The system stores the number you just dialed.

To redial a saved number:

1. Press a line key to preselect a line for the call.
If you have a Save Number Dialed key, you can skip
this step and have the system select a line for you.
2. Press DLSV or your Save Number Dialed key.
The stored number dials out.
If the outside line accessed is busy, you may be
able to dial 2 and wait for the line to become free.

162
80000mfh08-01.qxd 12/10/04 3:20 PM Page 163

Selectable Display Messaging

While you’re away from
your phone, display You can select a preprogrammed
Selectable Display Message for
telephone callers can your extension. Your display tele-
receive personalized text phone callers see the selected
message when they call your
messages you set up. extension. Selectable Display
Messaging provides you with per-
sonalized text messaging. For example, you can select the mes-
sage, “GONE FOR THE DAY.” Any co-worker calling from a dis-
play telephone sees the message. Other than displaying your mes-
sage, the call goes through normally.

There are 16 Selectable Display Messages (01-16), and each mes-

sage can be up to 20 characters long. When your system is first
installed, you have the following standard messages (although they
may have been changed during installation):
Message Number . . . . . . . . .Message
01 . . . . . . . . . . . . . . . . .CALL
02 . . . . . . . . . . . . . . .BACK BY
03 . . . . . . . . . . .MEETING IN ROOM
04 . . . . . . . . . . . . .OUT TO LUNCH
05 . . . . . . . . . . .GONE FOR THE DAY
06 . . . . . . . . . . . . .ON VACATION
07 . . . . . . . . . . .ON BUSINESS TRIP
08 . . . . . . . . . . . . .IN A MEETING
09 . . . . . . . . . . . . . . .OUT UNTIL
10-16 . . . . . . . . . . . . . .Undefined

Using the instructions that follow (see step 3), you can easily
scroll through all your system’s messages to see which are most
helpful to you. You can append (add characters to) any message,
provided the total message does not exceed 20 characters. The
characters you add apply only to your own phone.

163
80000mfh08-01.qxd 12/10/04 3:20 PM Page 164

Selectable Display Messaging

Selectable Display Messaging at your 22-Button or
34-Button Display Telephone
To select a Selectable Display Message:

1. Press and dial , or press your Call

Forwarding key.
OR
Press PGM + CFWD . You see:

2. Dial or press MORE + MSG . You see:

3. Dial the message number (01-16).

OR

Press or to scroll through the available

message numbers.

4. Press to select the message.

5. Press or to scroll through the text of the

available messages.
OR

Press to program or append the message text.

6. Enter any additional digits.

164
80000mfh08-01.qxd 12/10/04 3:20 PM Page 165

Selectable Display Messaging

The total number of digits/characters in the mes-
sage cannot exceed 20. Use any valid characters,
digits or symbols (just as if you were entering a
Speed Dial or extension name). Refer to the table
below when entering digits.

7. Press .
DND flashes.

To cancel Selectable Display Messaging:

1. Press and dial , or press your Call

Forwarding key.
OR

Press + PGM + CFWD . You see:

2. Dial , press , or press NONE to cancel

Selectable Display Messaging.
DND goes out.

165
80000mfh08-01.qxd 12/10/04 3:20 PM Page 166

Selectable Display Messaging

Selectable Display Messaging at your Super Display
Telephone
To select a Selectable Display Message:

1. Press and dial , or press your Call

Forwarding key.
OR
Press PROGRAM + CALL FWRD . You see:

2. Dial or press MESSAGE . You see:

3. Dial the message number (01-16).

OR

Press or to scroll through the available

message numbers.

166
80000mfh08-01.qxd 12/10/04 3:20 PM Page 167

Selectable Display Messaging

4. Press to select the message.

5. Press or to scroll through the text of the

available messages.
OR
Press to program or append the message text.
6. Enter any additional digits.
The total number of digits/characters in the mes-
sage cannot exceed 20. Use any valid characters,
digits or symbols (just as if you were entering a
Speed Dial or extension name). Refer to the table
below when entering digits.

7. Press .
DND flashes.

To cancel Selectable Display Messaging:

1. Press and dial , or press your Call

Forwarding key.
OR
Press PROGRAM + CALL FWRD . You see:

167
80000mfh08-01.qxd 12/10/04 3:20 PM Page 168

Selectable Display Messaging

2. Dial , press , or press NONE to cancel

Selectable Display Messaging.
DND goes out.

Entering Additional Characters

Use the following table when appending (adding digits/char-
acters to) Selectable Display Messages.
Name Programming
Press a key the indicated number of times for desired character

Key 1 Time 2 Times 3 Times 4 Times 5 Times 6 Times 7 Times 8 Times 9 Times
1 & - / ‘ 1
2 A B C a b c 2
3 D E F d e f 3
4 G H I g h i 4
5 J K L j k l 5
6 M N O m n o 6
7 P Q R S p q r s 7
8 T U V t u v 8
9 W X Y Z w x y z 9
0 space : 0
# Not used

* Not used

After selecting a letter, press a key for another letter or wait 2 seconds for the cursor to automatically advance.
Additional Name Programming Options
HOLD Save name. In system programming, HOLD saves and exits name programming.
CONF Exit name programming without saving name.
VOL Up Scroll the cursor to the left.
VOL Dn Scroll the cursor to the right.
MW Put the cursor after the last entry.
LND Delete the character under the cursor.
FLASH Delete the character to the right of the cursor.
CLEAR Clear the entire entry.
CHECK Restore the previous entry,

168
80000mfh08-01.qxd 12/10/04 3:20 PM Page 169

Selectable Display Messaging

– For Your Notes –

169
80000mfh08-01.qxd 12/10/04 3:20 PM Page 170

Speed Dial

Use Speed Dial instead

Speed Dial gives you quick access
of dialing long numbers. to frequently called numbers.
Instead of dialing a long tele-
phone number to reach a client or customer, use Speed Dial.
Speed Dial also lets you store Intercom digits for quick access to
commonly used features.

There are two types of Speed Dial: System and Personal. Speed
Dial numbers can be up to 16 digits long, using 0-9, # and *.
Every Speed Dial can have a programmed name up to 16 charac-
ters long. The name shows in your telephone’s display as the
Speed Dial number dials out.

Speed Dial can store outside numbers and Intercom digits. This
capability to store Intercom digits provides you with “one-touch”
access to features you use most often. For example, you can have
a Personal Speed Dial bin that simplifies forwarding calls to
Voice Mail or a co-worker.

Pressing SP DIAL 1 or SP DIAL 2 at your 34-Button Super

Display telephone will show the first 10 characters of the name
for the associated Personal Speed Dial bin. If you don’t have
names programmed, your phone will show the first 10 digits of
the stored number instead.

System Speed Dial

System Speed Dial gives you and your co-workers access to the
same set of stored numbers. Your system can have up to 1000
System Speed Dial numbers, depending on how it was set up dur-
ing installation. Check with your Communications Manager for
more about your System Speed Dial numbers.

170
80000mfh08-01.qxd 12/10/04 3:20 PM Page 171

Speed Dial
To program a System Speed Dial number:
Normally, only attendants and supervisors can
store System Speed Dial numbers. Find out from
your Communications Manager if you can.

1. Press and dial .

OR
Press PGM + SPD .
2. Dial the system bin number (normally 200-299).

3. Press .
4. Enter the line number you want the system to use when
dialing your stored number (e.g., 1 for line 1).
OR
Enter the line group number you want the system to use
when dialing your stored number (e.g., 90 for group 0).
OR

Press if you want to enter Intercom codes.

5. Press .
6. Enter the number you want to store (up to 16 digits long).
You can enter any combination of the digits 0-9, #
and *. To insert a pause in your Speed Dial number,
press MIC. To insert a Flash in your Speed Dial
number, press FLASH. These entries count as digits.

7. Press .
8. Enter a name for the Speed Dial number.
See Entering Speed Dial names for more.

9. Press .

171
80000mfh08-01.qxd 12/10/04 3:20 PM Page 172

Speed Dial
10. Repeat from step 2 to program another bin number.
OR

Press to exit.

To dial a System Speed Dial number:

1. Press and dial .

2. Dial the system bin number (normally 200-299).
OR
Press a Programmable Function Key for System Speed
Dial bin.
The stored number dials out.

172
80000mfh08-01.qxd 12/10/04 3:20 PM Page 173

Speed Dial
Personal Speed Dial
Personal Speed Dial provides 20 stored numbers just for your
own use. (If you have a DSS Console, the Personal Speed Dial
numbers on your console are the same as those on your phone.)

Your telephone has 10 Personal Speed Dial bin keys. Pressing

keys 1-10 accesses your first 10 Personal Speed Dial numbers
(701-710). Pressing DIAL and keys 1-10 accesses your second 10
Personal Speed Dial numbers (711-720).

If you have a 22-Button Standard or

22-Button Display Telephone, this is the
location of your 10 Speed Dial bin keys.

If you have a 34-Button Display

Telephone, this is the location of your 10
Speed Dial bin keys.

If you have a 34-Button Super Display

Telephone, this is the location of your 10
Speed Dial bin keys.

173
80000mfh08-01.qxd 12/10/04 3:20 PM Page 174

Speed Dial
To program a Personal Speed Dial number:

1. Press and dial .

OR
Press PGM + SPD .
2. Dial the personal bin number (normally 701-720).
OR
Press a Personal Speed Dial key (for bins 1-10).
OR

Press + a Personal Speed Dial key (for bins 11-20).

3. Press .
4. Enter the line number you want the system to use when
dialing your stored number (e.g., 1 for line 1).
OR
Enter the line group number you want the system to use
when dialing your stored number (e.g., 90 for group 0).
OR

Press if you want to enter Intercom codes.

5. Press .
6. Enter the number you want to store (up to 16 digits long).
You can enter any combination of the digits 0-9, #
and *. To insert a pause in your Speed Dial number,
press MIC. To insert a Flash in your Speed Dial
number, press FLASH. These entries count as digits.

7. Press .
8. Enter a name for the Speed Dial number.
See Entering Speed Dial Names on page 176 for
more.

174
80000mfh08-01.qxd 12/10/04 3:20 PM Page 175

Speed Dial

9. Press .
10. Repeat from step 2 to program another bin number.
OR

Press to exit.

To dial a Personal Speed Dial number:

1. Press and dial .

2. Dial the personal bin number (normally 701-720).
OR
Press a Personal Speed Dial key (for bins 1-10).
OR

Press + a Personal Speed Dial key (for bins 11-21).

OR
Press a Programmable Function Key for Personal Speed
Dial bin.
The stored number dials out.

To dial a Personal Speed Dial number if you have a

34-Button Super Display telephone:
1. Press SP DIAL 1 (for bins 701-710) or SP DIAL 2 (for
bins 711-720).
2. Press a Personal Speed Dial bin key.
The stored number dials out.

175
80000mfh08-01.qxd 12/10/04 3:20 PM Page 176

Speed Dial
Entering Speed Dial Names
Use the following table when entering Speed Dial names.
Name Programming
Press a key the indicated number of times for desired character

Key 1 Time 2 Times 3 Times 4 Times 5 Times 6 Times 7 Times 8 Times 9 Times
1 & - / ‘ 1
2 A B C a b c 2
3 D E F d e f 3
4 G H I g h i 4
5 J K L j k l 5
6 M N O m n o 6
7 P Q R S p q r s 7
8 T U V t u v 8
9 W X Y Z w x y z 9
0 space : 0
# Not used

* Not used

After selecting a letter, press a key for another letter or wait 2 seconds for the cursor to automatically advance.
Additional Name Programming Options
HOLD Save name. In system programming, HOLD saves and exits name programming.
CONF Exit name programming without saving name.
VOL Up Scroll the cursor to the left.
VOL Dn Scroll the cursor to the right.
MW Put the cursor after the last entry.
LND Delete the character under the cursor.
FLASH Delete the character to the right of the cursor.
CLEAR Clear the entire entry.
CHECK Restore the previous entry,

User Programmable Feature

#SP
Program Personal and System Speed Dial Numbers. See
User Programmable Features at the end of this guide
for more.

176
80000mfh08-01.qxd 12/10/04 3:20 PM Page 177

Split
Switch between active
calls without Conferencing With Split, you can split (alternate)
between your current call and a
the calls together. new call. Split lets you easily alter-
nate between the calls without
joining (Conferencing) your callers together.

Split requires a uniquely programmed Split Programmable

Function key. Check with your Communications Manager to find
out if you have this type of key.
To Split between your current Intercom call and a new
Intercom call:

1. Press to place your current Intercom call on Hold,

then hang up.
2. Place or answer Intercom call.
3. Press your Split key to switch between your two
Intercom calls.

To Split between your current outside call and an Intercom

call:

1. Press to place outside call on Hold, then hang up.

2. Place or answer waiting Intercom call.
3. Press your Split key to switch between your Intercom
call and the outside call.

177
80000mfh08-01.qxd 12/10/04 3:20 PM Page 178

Split
To Split between your current Intercom call and an outside
call:

1. Press to place your current Intercom call on Hold.

2. Place or answer outside call.
3. Press your Split key to switch between your two calls.

To Split between your current outside call and a waiting

outside call:

1. Press to place your current outside call on Hold,

then hang up.
2. Place or answer a new outside call.
3. Press your Split key to switch between your two calls.

178
80000mfh08-01.qxd 12/10/04 3:20 PM Page 179

Tandem Trunking
Join two callers in
Conference, leave the Tandem Trunking (Unsupervised
Conference) allows you to join
call and let their two outside callers in a
conversation continue. line-to-line Conference. You can
then drop out of the call, leaving
your callers in an unsupervised Conference. You are no longer
part of the conversation. The Conference continues until either
outside party hangs up. Find out from your Communications
Manager if you are able to set up an Unsupervised Conference.
To set up a tandem call (Unsupervised Conference):
1. Place or answer an outside call.

2. Press or CONF .
3. Place or answer another outside call.

4. Press or CONF to set up the Conference.

5. Hang up.
If the outside lines disconnect when you hang up in
this step, you do not have Tandem Trunking capability.
You can optionally press HOLD to place the
Conference on Hold. Your callers hear Music on Hold
(if installed) while waiting on Hold. Just press a line
key then CONF again to reinstate the Conference.

To disconnect a tandem call (using Forced Trunk

Disconnect):
1. Press line key for busy line.
OR

Press and dial the line’s Direct Line Access code

(e.g., 101 for line 1).
2. Dial # or press DISC to disconnect the line.

179
80000mfh08-01.qxd 12/10/04 3:20 PM Page 180

Tandem Trunking
To Barge In on a tandem call:
Use this procedure to rejoin a Conference already
in progress.
1. Press line key for busy line.
OR

Press and dial the line’s Direct Line Access code

(e.g., 101 for line 1).

2. Dial or press BARG .

Time and Date

The time and date shows

The time and date appear on
on all telephone displays. all telephone displays in your
system. Follow the User
Programmable Feature steps referenced below if you need to reset
the system time and date (e.g., after the Daylight Savings Time
change).

User Programmable Feature

#TD
Change your system’s time and date. See User
Programmable Features at the end of this guide for more.

180
80000mfh08-01.qxd 12/10/04 3:20 PM Page 181

Transfer

Send the outside call you

Transfer permits you to send your
are on to a co-worker. active outside call to a co-worker,
Ring Group, UCD Hunting Group
or Voice Mail. With Transfer, you can quickly send a call to the
desired co-worker. A call you Transfer automatically recalls to
you if not picked up at the Transfer destination. If you don’t
answer the recall, the call will ring other co-workers or the atten-
dant. This assures that you do not lose or inadvertently abandon
your transfers.

Your telephone system allows the following types of transfers:

● Screened Transfer
With Screened Transfer, you announce the call to the destina-
tion before hanging up to complete the Transfer.
● Unscreened Transfer
With Unscreened Transfer, you Transfer the call without
making an announcement.
● Handsfree Transfer
Use Handsfree Transfer to send an outside call to a co-work-
er’s speakerphone. This allows your co-worker to converse
with the transferred caller just by speaking toward their
phone — without lifting the handset.

To Transfer your call:

1. Do not hang up.

2. Press .
3. Dial your co-worker’s extension.
OR
Press a DSS key.
OR
Dial a Ring Group or UCD Hunting Group master number.

181
80000mfh08-01.qxd 12/10/04 3:20 PM Page 182

Transfer
4. Announce the call to make a Screened Transfer.
OR
Press the flashing line key to return to your call if your
co-worker doesn’t want it (i.e., rejects the call).
OR
Hang up to send the call through unscreened.
The call will recall to you if unanswered at the
destination.

To Transfer your call to a co-worker’s mailbox:

1. Do not hang up.

2. Press .
3. Dial your co-worker’s extension.

4. Press or MBOX .
5. Hang up.

To Transfer a call to a co-worker’s speakerphone:

1. While on an outside call, press and dial your
co-worker’s extension number
OR
Press the Hotline key for your co-worker.
– Listen for 2 beeps. (This means that your Transfer
announcement has voice-announced at your
co-worker’s phone.)
– If your co-worker’s phone is set up to ring instead of
voice-announce, you cannot use Handsfree Transfer.
2. Press to send the call directly to your co-worker’s
speakerphone.
OR

Press to get Intercom dial tone and select another

co-worker for the Transfer.

182
80000mfh08-01.qxd 12/10/04 3:20 PM Page 183

Transfer
Transfer Recall
Your telephone display can show the type of call recalling, as well
as which co-worker initially transferred the call.

Following are the displays you see at your phone when a transferred
call is recalling. In the first example, the call was transferred by
extension 301 (which does not have a name). In the second example,
the call was transferred by extension 300 (which has the name
ATTENDANT).

183
80000mfh08-01.qxd 12/10/04 3:20 PM Page 184

Trunk (Line) Queuing and Callback

When all outside lines are
busy, Line Queuing lets Line Queuing permits you to
queue (wait in line) on hook for a
you wait in line for a line busy line or line group to become
to become free. free. The system will connect you
as soon as the line is available.
— You do not have to manually retry
Line Callback will the line later.
automatically call you back After queuing for a line, you just
when a line is available. hang up to convert your Line
Queue into a Line Callback. When
the line becomes free, the system automatically recalls your phone.
As soon as you lift the handset, you connect to the outside line.

You can leave a Line Callback request for many outside lines.
The system processes your requests as the lines become free. In
addition, you and your co-workers can leave a Callback request
for the same line. The system processes these requests on a
first-in/first-out (FIFO) basis.

If you leave a Line Callback request and fail to answer when

Callback rings your phone, the system cancels the Callback.

Line Queuing Priority

You may have Line Queuing Priority enabled for your telephone.
If you do, when you queue for a busy line Line Queuing will con-
nect you before your co-workers that don’t have priority. Your
Communications Manager can can tell you if you have Line
Queuing Priority.

184
80000mfh08-01.qxd 12/10/04 3:20 PM Page 185

Trunk (Line) Queuing and Callback

To queue for a busy line:
1. Press line key for busy line.
OR

Press and dial the line’s Direct Line Access code

(e.g., 101 for line 1).

2. Dial ; do not hang up.

3. When the line becomes free, you automatically connect.
When you hear dial tone from the line, you can
place your call again.

To leave a Line Callback for a busy line:

1. Press line key for busy line.
OR

Press and dial the line’s Direct Line Access code

(e.g., 101 for line 1).

2. Dial or press CLBK , then hang up.

3. When the line becomes free, the system automatically
calls you back.
If you answer within 4 rings, you hear dial tone
from the outside line.
If you don’t answer the Callback ring, your phone
system cancels the Callback.

185
80000mfh08-01.qxd 12/10/04 3:20 PM Page 186

User Programmable Features

Set up your telephone to

The User Programmable Features
meet your own unique allow you to customize your tele-
requirements.. phone to work just the way you
want. You’ll no longer have to rely
on your System Administrator or
Communications Manager to set up your phone.

Using the chart on the next page, the User Programmable

Features let you customize the following features:
● Headset Mode
● Hotline Key Assignment
● Off Hook Signaling (Setup)
● Paging (Incoming)
● Prime Line Assignment
● Programmable Function Key Assignment
● Programmable Function Key Ringing (for Call Coverage
Keys, Group Call Pickup Keys, and Line Keys)
● Programmable Idle Menu Soft Keys (Super Display)
● Ringing Line Preference
● Speed Dial Bin Setup (Personal and System)
● Time and Date
● Voice Announce (for incoming Intercom calls)
● Voice Over

Note: The ability to use certain User Programmable Features may

be restricted by your telephone’s programmed Access Level.
Check with your Communications Manager if you need to use a
User Programmable Feature that is restricted.

186
80000mfh08-01.qxd 12/10/04 3:20 PM Page 187

User Programmable Features

User Programmable Features
To program a feature, press # and the feature’s code. For example, to enable incoming Paging, press # and dial V P Y, then SPK to
hang up. By default, Call Forwarding Clear All, System Speed Dial, and Time and Date are only available to the attendant.
Feature Mnemonic Numeric Operation

Call Forwarding Clear All #CC #22 #CC + Y to clear (cancel) forwarding or N to exit without clearing +
SPK to hang up.
Headset Mode #HS #47 #HS + Y to enable or N to disable + SPK to exit.
Hotline #HL #45 #HL + Press flashing Hotline key + Enter extension for new Hotline
partner + HOLD + Program another Hotline key or SPK to exit.
Off Hook Signaling #OHS #647 #OHS + Select mode (C=Outside line, I=ICM, D=Hotline) + Select
option (see below) + SPK to exit.
Outside line options: C=Camp On tone, O=Off Hook Ringing, 0 = None
Intercom options: C=Camp On, V=Voice Over, 0=None
Hotline Options: C=Camp On, V=Voice Over, 0=None,
Paging (Incoming) #VP #87 #VP + Y to enable or N to disable + SPK to exit.
Prime Line Assignment #PLA #752 #PLA + Press one of your flashing programmable keys or ICM +
SPK to exit.
Programmable Function #KP #57 #KP + Press key you want to program + HOLD + ICM + Press VOL
Key Assignments ▲ or VOL ▼ to select key option + HOLD + (Enter any additional
data if required1 + HOLD) + Press VOL ▲ or VOL ▼ to select another
key to program, or CONF + SPK to exit.
1
To set up a Night (System Mode System) key, press CLEAR instead
of entering additional data.
Programmable Function #RAC #722 Call Coverage Keys: #RAC + Call Coverage Key repeatedly to select
Key Ringing ringing mode + SPK to exit.
Call Coverage Keys flash as follows: Lamp only=On red, Immediate
ring=On green, Delay ring=Fast flash green.
#RAL #725 Outside Line Keys: #RAL + Line Key repeatedly to select ringing
mode + SPK to exit.
Line keys flash as follows: Lamp only=On red, Immediate ring=On
green, Delay ring=Fast flash green, Night ring=Slow flash green.
#RAP #727 Group Call Pickup Keys: #RAP + Group Call Pickup Key repeatedly
to select ringing mode + SPK to exit.
Group Call Pickup Keys flash as follows: Lamp only=On red, Imme-
diate ring=On green, Delay ring=Fast flash green.
Programmable Idle Menu #SM #76 Press the soft key you want to program (or press Vol ▲ or Vol ▼ to
Soft Keys (Super Display) scroll through the keys) + HOLD + ICM + Vol ▲ or Vol ▼ to select
key option + HOLD + CONF + SPK to exit.
Ringing Line Preference #RLP #757 #RLP + Y to enable or N to disable + SPK to exit.
Speed Dial, Personal #SP #77 #SP + Press bin key (for bins 701-710) or DIAL then bin key (for bins
711-720) + HOLD + Dial outside line (e.g., 1), Line group (e.g., 90-
98), or ICM for Intercom feature + HOLD + Number to store + HOLD
twice + Name + HOLD + Press another bin key or SPK to exit.
Speed Dial, System #SP #77 #SP + Dial System Speed Dial bin number (e.g., 200) + HOLD +
Dial outside line (e.g., 1), Line group (e.g., 90-98), or ICM for Inter-
com feature + HOLD + Number to store + HOLD twice + Name +
HOLD + Dial another System Speed Dial bin or SPK to exit.
System Program Access #*#* #*#* + Enter programming password.
Time and Date #TD #83 #TD + Enter time in 24-hour clock using hours (2 digits), minutes (2
digits) and seconds (2 digits) + HOLD + Enter date using month (2
digits), day (2 digits) and year (4 digits) + HOLD + SPK to exit.
Intercom Voice Announce #VA #82 #VA + V for voice announce or R for ring + SPK to exit.
(for incoming Intercom calls)

187
80000mfh08-01.qxd 12/10/04 3:20 PM Page 188

Voice Mail
End the frustration of
missed calls, inaccurately Your system may use an IntraMail,
UltraMail, or NVM-Series Voice
written messages and Mail with Automated Attendant
telephone tag. system. Voice Mail provides com-
prehensive voice messaging capa-
bility as well as a sophisticated Automated Attendant, including:
● Automated Attendant
Automated Attendant automatically answers your system’s
incoming calls. After listening to a customized Automated
Attendant greeting, callers to your company can dial a system
extension or use Voice Mail.
● Leaving a Message
When you call a co-worker who doesn’t answer, is busy on
the phone or in Do Not Disturb, you can easily leave them a
voice message in their mailbox. There is no need for you to
call back later.
● Call Forwarding to Voice Mail
When you forward your calls to Voice Mail, calls to your
phone go to your Voice Mail mailbox. Your callers then leave
you a voice message instead of calling back later. You can
enable forwarding for all calls immediately, for unanswered
calls, or for calls to your phone when you are busy.
● Transferring to Voice Mail
You can Transfer a call to your mailbox or a co-worker’s
mailbox. After the Transfer goes through, your caller will
hear your co-worker’s entire greeting and can leave a mes-
sage in the mailbox.
● Conversation Record
While on a call, you can have Voice Mail record your conver-
sation. You just press your uniquely programmed Conversation
Record key or a soft key. Once recorded, Voice Mail stores the
conversation as a new message in your mailbox. After calling
your mailbox, you can save, edit or delete the recorded conver-

188
80000mfh08-01.qxd 12/10/04 3:20 PM Page 189

Voice Mail
sation. (Check with your Communications Manager to see if
you have Conversation Record capability.)
You can also have Conversation Record keys for a co-work-
er’s mailbox. While on a call, you can press the key to record
your conversation directly into the corresponding mailbox
● Personal Answering Machine Emulation
You can have your idle telephone emulate a personal answer-
ing machine. This lets Voice Mail screen your calls, just like
your answering machine at home. If activated, your incoming
calls route to your mailbox. Once your mailbox answers, you
hear two alert tones followed by your caller’s incoming mes-
sage. You can then:
- Let the call go through to your mailbox.
- Intercept the call.
● Message Center Mailbox
A Message Center Mailbox is a mailbox shared by more than
one co-worker. You access the Message Center by pressing a
Message Center key on your phone. (Ask your Communications
Manager if you have this key.) Press the key to:
- Listen to the messages stored in the Message Center mailbox.
- Transfer calls to the Message Center mailbox.
- Use many other Voice Mail features.
A Message Center Mailbox may help you if you work closely
with a group of co-workers. For example, your group’s super-
visor can send important messages to the shared Message
Center Mailbox, and members of your group can review them
as time allows.
● Interactive Soft Key Shows New Messages
Your soft keys show the number of new messages in your mail-
box. For example, if you have 2 new messages in your mailbox,
your Voice Mail soft key shows VM02 (display telephone) or
V-MAIL 02 (34-Button Super Display telephone). The new mes-
sage count resets to 00 as soon as you call your mailbox
(regardless of whether you listened to your new messages). The
message count returns when you get new messages.

189
80000mfh08-01.qxd 12/10/04 3:20 PM Page 190

Voice Mail
Calling Your Mailbox
To call your mailbox:
Your MW key and Ring/Message lamp flash fast
when you have new messages in your mailbox.
1. Press VM00 or V-MAIL 00 .
OR

Press .
OR

Press , then dial the Voice Mail master number

(e.g., 700) followed by your mailbox number.
Your mailbox number is normally the same as
your extension number. You may optionally dial a
co-worker’s mailbox — or use this procedure to call
your mailbox from a co-worker’s phone.
2. Lift handset for privacy.
3. If requested by Voice Mail, enter your security code.
Your Ring/Message lamp will go out after you
call your mailbox.
Your MW key will be on while you are connected
to your mailbox.

To hang up after calling your mailbox:

1. Press .
Your MW key will go out.

190
80000mfh08-01.qxd 12/10/04 3:20 PM Page 191

Voice Mail
Leaving a Message
To leave a message in the mailbox of an unanswered
extension:
The extension you call can be busy, in Do Not
Disturb, or unanswered.

1. Press or MSG .
The Voice Mail system will prompt you to leave a
message.

Forwarding Calls to your Mailbox

To activate or cancel Call Forwarding:

1. Press and dial .

OR
Press PGM + CFWD .
2. Dial the Call Forwarding type:
0 = Cancel forwarding
2 = Busy/No Answer
4 = Immediate
6 = No Answer

3. Press to forward to Voice Mail.

4. Press to hang up.

Your DND key is on while your calls are forwarded.

191
80000mfh08-01.qxd 12/10/04 3:20 PM Page 192

Voice Mail
Transferring Calls to a Mailbox
To Transfer your active call to a mailbox:
Method A

1. Press .
2. Dial the number of the mailbox to receive the Transfer
(e.g., 301 for extension 301).
This number can be your mailbox number (if
you’re away from your desk) or a co-worker’s mail-
box number.

3. Press or MBOX .

4. Press to hang up.

Voice Mail will prompt your caller to leave a
message in the mailbox you selected.
Method B

1. Press .

2. Press DSS key for co-worker’s extension + .

3. Press to hang up.

Voice Mail will prompt your caller to leave a
message in the mailbox you selected.
Method C
1. Press keyset or DSS Console Hotline key.

2. Press .

3. Press to hang up.

Voice Mail will prompt your caller to leave a
message in the mailbox you selected.

192
80000mfh08-01.qxd 12/10/04 3:20 PM Page 193

Voice Mail
Conversation Record
To record your active call in your mailbox:
Only one party on a call can use Conversation
Record at any one time. This includes Intercom calls
and Conference calls.
1. Press REC or your Voice Mail Record key.
Your Record key lights green while your system calls
your mailbox. Once recording begins, the key flashes
fast and you hear the voice prompt, “Recording.”
You can also have a Record key on your DSS
Console. It lights red while the system calls your
mailbox and flashes fast once recording begins.

To stop Conversation Record:

1. Press .

Personal Answering Machine Emulation

To activate Personal Answering Machine Emulation from
your 22-Button or 34-Button Telephone:

1. Press and dial , or press your Call

Forwarding key.
OR
Press PGM + CFWD . You see:

2. Dial or press MORE + AME . You see:

193
80000mfh08-01.qxd 12/10/04 3:20 PM Page 194

Voice Mail

Dial or press ALL to forward all calls.

OR

Dial or press TRNK to forward just outside calls.

Your DND key flashes.

To cancel Personal Answering Machine Emulation at your

22-Button or 34-Button Telephone:

1. Press and dial , or press your Call

Forwarding key.
OR

Press PGM + CFWD . You see:

2. Dial , press , or press NONE to cancel for-

warding.
Your DND key goes out.

194
80000mfh08-01.qxd 12/10/04 3:20 PM Page 195

Voice Mail
To activate Personal Answering Machine Emulation from
your Super Display Telephone:

1. Press and dial , or press your Call

Forwarding key.
OR
Press PROGRAM + CALL FWRD . You see:

2. Dial or press ANS MACHINE . You see:

Dial or press ALL to forward all calls.

OR

Dial or press TRUNK ONLY to forward just out-

side calls.
Your DND key flashes.

195
80000mfh08-01.qxd 12/10/04 3:20 PM Page 196

Voice Mail
To cancel Personal Answering Machine Emulation at your
Super Display Telephone:

1. Press and dial , or press your Call

Forwarding key.
OR
Press PROGRAM + CALL FWRD . You see:

2. Dial , press , or press NONE to cancel for-

warding.
Your DND key goes out.

When Answering Machine Emulation broadcasts your caller’s

message, you can:
While you are listening to the broadcast, SPK flash-
es and MW lights steadily on,
● Do nothing to have the caller’s message automatically
recorded in your mailbox.
OR
● Press SPK or lift the handset to intercept the call.
If your extension is in the headset mode, you can
only press SPK.
● Press MW to switch to the Call Screening mode (see the
next page).

196
80000mfh08-01.qxd 12/10/04 3:20 PM Page 197

Voice Mail
To intercept the call (and stop recording the message):
● Press ANSWER (ANSW) or flashing MW.

To screen your caller’s message as your mailbox records it:

●. Press SCREEN (SCRN) .
— To intercept the call (and stop recording the message):
Press ANSWER (ANSW) , or
Press SPK, or
Lift the handset, or
Press MW.
— To continue listening to your caller’s message as it is
being recorded:
Do nothing.
— To exit Call Screening and allow the message to continue
recording in private:
Press EXIT .
— To use another feature or process another call:
Press any other feature key.

To exit Call Screening and allow the message to continue

being recorded in private:
● Press EXIT .

To use another feature or process another call:

● Lift the handset, or
Press SPK, or
Press any other feature key.
Call Screening is only functional while the tele-
phone is on-hook.

197
80000mfh08-01.qxd 12/10/04 3:20 PM Page 198

Voice Mail
Checking Your Messages
To check your messages:

1. Press .
You see: Number of MSG = n (where n is the
number of new messages in your mailbox).

Message Center Mailbox

The Message Center key flashes fast (green) when
there are new messages not listened to in the
Message Center mailbox.

To call the Message Center:

1. Press or lift the handset.

2. Press the Message Center key.
3. If requested by Voice Mail, enter the security code for
the Message Center mailbox.

To Transfer a call to the Message Center:

1. When on an Intercom or outside call, press the Message
Center key.
2. Hang up.
Your caller will be prompted to leave a message
in the Message Center mailbox.

198
80000mfh08-01.qxd 12/10/04 3:20 PM Page 199

Voice Mail

– For Your Notes –

199
80000mfh08-01.qxd 12/10/04 3:20 PM Page 200

Voice Over
Get through to a
Voice Over lets you get through to
co-worker busy on a
a co-worker busy on a handset
handset call — without call. With Voice Over, the person
interrupting their call. you call hears an alert tone fol-
lowed by your voice. They can
respond to you without being
heard by their original caller. They can also easily switch between
you and their first caller.

Voice Over could help a lawyer, for example, waiting for an urgent
call. While on a call with another client, the lawyer’s paralegal
could announce the urgent call as soon as it comes in. The lawyer
could then give the paralegal instructions on how to handle the sit-
uation — all without the original client hearing the conversation.
To initiate a Voice Over to a busy extension:
You can only leave a Voice Over if you hear
busy/ring tone.

1. Dial or press VOVR .

You hear two beeps, then you can speak with your
co-worker.

To respond to a Voice Over alert tone at your extension:

You hear two beeps while on a handset call.

1. Press and hold .

Release your MIC key to talk to your initial caller.
You can repeat this procedure as long as the Voice
Over initiator doesn’t hang up.

200
80000mfh08-01.qxd 12/10/04 3:20 PM Page 201

Volume and Contrast Control

Adjust the volume of your

You can easily adjust the volume
call, as well as your of your phone and the contrast of
phone’s display contrast. the display. The volume and dis-
play settings you make are
“remembered” by the system in
the event of a power down or system reset.
Volume Control
Your telephone provides individual 7-step volume controls for the
following features while they are active:
– Intercom handset calls
– Intercom Handsfree calls
– Outside call handset calls
– Outside call Handsfree calls
– Paging (receive volume)
– Background Music
– Ringing
Using the Volume Control Soft Keys
You can additionally use your telephone’s soft keys to adjust the vol-
ume of your on-hook ringing, off-hook ringing and Paging (receive).
To adjust the ringing, off-hook ringing or incoming Page
volume at your 22- button or 34- button telephone:
1. While your phone is idle, press PGM. You see:

2. Press MORE. You see:

201
80000mfh08-01.qxd 12/10/04 3:20 PM Page 202

Volume and Contrast Control

3. Press VOL. You see:

4. Press the key for the type of volume you want to adjust:
– RING = Ringing
– OFHK = Off-hook ringing
– PAGE = Page announcements (incoming)
You see (ringing shown):

5. Press or to adjust the selected volume.

– The number to the right of the display indicates the
current setting (1-7).

To adjust the ringing, off-hook ringing or incoming Page

volume at your Super Display telephone:
1. While your phone is idle, press PROGRAM. You see:

2. Press VOLUME. You see:

202
80000mfh08-01.qxd 12/10/04 3:20 PM Page 203

Volume and Contrast Control

3. Press the key for the type of volume you want to adjust:
– RING = Ringing
– OFF-HK RING = Off-hook ringing
– PAGE = Page announcements (incoming)
You see (ringing shown):

4. Press or to adjust the selected volume.

– The number to the right of the display indicates the
current setting (1-7).

Contrast Control
Press or while your 22-button or 34-button dis-
play telephone is idle to adjust the display contrast. There are 7
steps in this adjustment. Note that Contrast Control is not avail-
able if you have a Super Display telephone.

203
80000mfh08-01.qxd 12/10/04 3:20 PM Page 204

Walking Class of Service

Use your Toll Restriction
Walking Class of Service allows
and Class of Service at a
you to temporarily implement
co-worker’s phone. your Toll Restriction and Class of
Service settings at a co-worker’s
phone. You would normally do this to override dialing restrictions
at a telephone. For example, if you are an executive with an unre-
stricted phone you can walk to any phone in the building, imple-
ment Walking Class of Service, and dial without restriction. After
the phone goes idle, Walking Class of Service remains in effect
for 10 seconds. This permits you to make multiple calls before the
phone returns to its normal restrictions. Ask your
Communications Manager if you can use Walking Class of
Service.
To enable Walking Class of Service at a co-worker’s extension:

1. Press .

2. Dial .
At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

204
80000mfh08-01.qxd 12/10/04 3:20 PM Page 205

Walking Class of Service

3. Enter your own extension number + .

When entering an extension or PIN number:
- CLEAR erases your entire entry.
- LND backspaces over (erases) the last digit entered.
At a 22- or 34-Button Display Telephone, you see:

At a Super Display Telephone, you see:

4. Enter your PIN number + .

If your extension does not have a PIN number, turn
to Entering or Changing Your PIN Number on page
96. You must have a PIN number to use this feature.
If your extension does not have Walking Class of
Service capability, you will hear error tone.
5. Place any call or use any feature allowed by your Toll
Restriction and Class of Service settings.
You can place additional calls. Walking Class of
Service will automatically deactivate after 10 seconds.

205
80000mfh08-01.qxd 12/10/04 3:20 PM Page 206

– For Your Notes –

206
80000mfh08-01.qxd 12/10/04 3:20 PM Page 207

Your Super Display Telephone

80000 - 71
CHECK CLEAR

LINE 1 LINE 2 LINE 3 LINE 4 LINE 5 LINE 6

For Attendants:
LINE 7 LINE 8 LINE 9 LINE 10 LINE 11 LINE 12 Key 11=Night Key
Key 24=Operator Call Key

Keys 13-24 are undefined

for non-attendants in DS2000.
ABC DEF
MW ICM
Keys 7-24 are undefined for
1 2 3 non-attendants in DS1000.
GHI JKL MNO FLASH DND

4 5 6
PQRS TUV WXYZ DIAL MIC

7 8 9
OPER LND SPKR

0
VOL CONF
HOLD

● The Ring/Message Lamp at the top of your telephone flashes slowly green while a call
rings your telephone, blinks green if you have new Caller ID calls, and flashes red for
new Voice Mail messages or Message Waiting.
● Your key assignments may be different than shown. Ask your Communications Manager.
● See the inside front cover of this guide for an illustration of the 34-Button Display telephone.
80000mfh08-01.qxd 12/10/04 3:20 PM Page 208

NEC Unified Solutions, Inc.

4 Forest Parkway, Shelton, CT 06484
TEL: 203-926-5400 FAX: 203-929-0535
www.necunifiedsolutions.com

*80000MFH08* December 10, 2004

Printed in U.S.A.
80000MFH08