TURBINE SUBMITTAL

Quote Number: 9001-170718-118:1

Model: VIS-WF
Size: 7CLC 8 Stage(s)

OPERATING CONDITIONS
Temp / SG: 70.00° F / SP.GR 0.9999
Fluid type: Water
Vapor pressure 0.3633 psi
Viscosity 0.9695 cP
Specified flow: 317.00 USGPM
Total dynamic head: 838.00 ft
Pumping level: 0.00 ft

PERFORMANCE AT 3550 RPM

Bowl efficiency: 80.10 % @design, 81.10 % Best Efficiency
Run out capacity: 508.00 USGPM
Power: 84 Hp @design, 94.90 Hp NOL
NPSHr: 16.20 ft @design
Design thrust: 2957.50 lb @design
Shut off pressure: 462.29 psi

MATERIALS AND DIMENSIONS

Bowl: Cast Iron CL30 Enamel
Bowl Wear Ring Material: None
Impeller: 316SS
Impeller Wear Ring
Not Included
Material:
Impeller Balance: Mnf.Standard
Impeller Lock Method: Taper lock
Impeller diameter: 5.125 inch
Bowl shaft: 416SS, 1.188 inch diam.
Suction adapter bearings Bronze C90300 "G" Modified
Bowl bearings: Bronze
Suction adapter: Ductile Iron 65-45-12
Bowl features No Added Features
TPL: 0.00 ft
Sump/Pit Depth: 0.00 ft
Documentation: Standard pump installation and operation manual and order data

TESTING
Hydrostatic: None
Performance: None
Final Inspection: None
Other: None

COATING
Goulds Water Technology Standard Blue Enamel; Bowl Assembly - STD; Riser Assembly - STD; Head Assembly -
Coating information:
STD
DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED
Certified by:
Date
Quotation number: 9001-170718-118
Project:
Tag:
 TURBINE SUBMITTAL
Quote Number: 9001-170718-118:1
Model: VIS-WF
Size: 7CLC 8 Stage(s)

ADDITIONAL FEATURES
Check valve: None
Sanitary Well Seal: No
Additional bowl features:
Additional riser features:
Additional driver features:
Additional head features:
Additional misc. features:

WEIGHTS
Total bowl weight: 271 lbs
Column weight: 0 lbs
Head weight: 0 lbs
Driver weight: 0 lbs
Total unit weight: 271 lbs

Our offer does not include specific review and incorporation of any Statutory or Regulatory Requirements and the offer is limited to the
requirements of the design specifications. Should any Statutory or Regulatory requirements need to be reviewed and incorporated then the
Customer is responsible to identify those and provide copies for review and revision of our offer.

Our quotation is offered in accordance with our comments and exceptions identified in our proposal and governed by our standard terms and
conditions of sale – Xylem Americas attached hereafter.

For units requiring performance test, all performance tests will be conducted per ANSI/HI 14.6 standards unless otherwise noted in the
selection software submittal documents. Test results meeting with grade 2B tolerances for pumps with a rated shaft power of 134HP or less
and grade 1B for greater than 134HP will be considered passing.
Customer is responsible for verifying that the recommendations made and the materials selected are satisfactory for the Customer's intended
environment and Customer's use of the selected pump. Customer is responsible for determining the suitability of Xylem recommendations
for all operating conditions within Customer's and/or End User's control. Xylem disclaims all warranties, express or implied warranties,
including, but not limited to, warranties of merchantability and fitness for a particular purpose and all express warranties other than the
limited express warranty set forth in the attached standard terms and conditions of sale – Xylem Americas attached hereafter.

Xylem does not guarantee any pump intake configuration. The hydraulic and structural adequacies of these structures are the sole
responsibility of the Customer or his representatives. Further, Xylem accepts no liability arising out of unsatisfactory pump intake field
operating conditions.

The Customer or his representatives are referred to the Hydraulic Institute Standards for recommendations on pump intake design. To
optimize the hydraulic design of a field pump intake configuration, the Customer should strongly consider performing a detailed scale model
pump intake study. However, the adequacies of these recommendations are the sole responsibility of the Customer.

DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

Certified by:
Date
Quotation number: 9001-170718-118
Project:
Tag:
 HYDRAULIC ANALYSIS
Quote Number: 9001-170718-118:1
Model: VIS-WF
Size: 7CLC 8 Stage(s)

OVERALL PUMP PARAMETERS

Capacity: 317.00 USGPM Total Dynamic Head: 838.00 ft
Total Pump Length: 0.00 ft Impeller Trim: 5.125 inch
VIS -Submersible Vertical
Pump Type: Number of Stages: 8
Turbine (Borehole) Pumps
Pump K-Factor: 3.50 lbs/ft Pumping Level: 0.00 ft
Additional Pump K-Factor: 3.50 lbs/ft
Pump Operating Speed [RPM]: 3550

BOWL DATA
Total Bowl Length: 57.830 inch Bowl Shaft Limit : 245 Hp
Bowl Shaft Diameter: 1.188 inch Bowl Shaft Material: 416SS
Bowl Diameter: 7.120 inch

COLUMN DATA
Column Diameter : 4 inch Column Elongation: 0.00000 inch
Column Wall Thickness: 0.230 inch Shut Off Column Elongation: 0.00000 inch
Column Load: 65.40 lb

HORSEPOWER DATA
Bowl Hp at Design: 84 Hp Rating: 100 Hp [75 kW]
Thrust Load Loss: 0.00000 Hp

OTHER DATA
Hydraulic Thrust: 2932.70 lb Actual Head Above Grade: 837.22 ft
Thrust at Shut Off: 3762.43 lb Shut Off Discharge Pressure: 462.29 psi
Column Loss: 0.04 ft NPSHa: 34.00 ft
Head Loss: 0.75 ft NPSHr: 16.20 ft @design
Total Loss: 0.78 ft NPSH Margin: 2.00 ft
Thrust at Design: 2957.50 lb

EFFICIENCY DATA
Bowl Efficiency: 81.10 % Overall Efficiency: 0.00 %
Motor Efficiency: 0.00 % KWH per 1000 gallons: 0.00
Pump Efficiency: 80.00 %

FLUID DATA
Fluid Type: Water Specific Gravity: 0.9999
Temperature: 70.00°F Viscosity: 0.9695 cP

COMPONENT WEIGHTS
Bowl Weight: 271 lbs Column Weight: 0 lbs
Head Weight: 0 lbs Can Weight:
Driver Weight: 0 lbs Total Pump Weight: 271 lbs

DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

Certified by
Date of certification
Pump serial number
Project Name
Tag
 OUTLINE DRAWING
Quote Number: 9001-170718-118:1
Model: VIS-WF
Size: 7CLC 8 Stage(s)

PUMP DATA DIMENSIONS

No. of Units 1.00 each AD 0.00 inch
Model: VIS-WF 7CLC BL 57.83 inch
Stages: 8 COL 4.00 inch
Riser Size: 4 DD 0.00 inch
Flow: 317.00 USGPM MIN SUB 17.23 inch
Head: 838.00 ft DH 0.00 inch
Driver Mfq: G 0.00 inch
Rating: 100 Hp [75 kW] H 0.00 inch
Speed: 3550 RPM HH 0.00 inch
PH: J 0.00 inch
Frequency: 60 Hz K 0
Voltage: MD 0 inch
ML 0.00 inch
E (R) 0.00 inch
TPL 0.00 inch
CV Dia.
Head
Flanged 300#
Rating
Weights
Total bowl 271 lb
Total column 0.00 lb
Discharge head 0 lb
Driver 0 lb
Approx weight 271 lb

No. NOTES

T.P.L. (Total Pump Length) is the

distance to lowest projection on pump ±
1 1.0 inch.
DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED
Tolerance on all dimensions is .12 or ± Certified by
2 .12 inch per 5 ft, whichever is greater.
Date of certification
All dimensions shown are in inches
Pump serial number
3 unless otherwise specified.
Project Name
Drawing not to scale.
4 Tag
 CROSS SECTIONAL
Quote Number: 9001-170718-118:1
Model: VIS-WF
Size: 7CLC 8 Stage(s)

BILL OF MATERIAL
ITEM Part Name CODE MATERIAL ASTM#

Bowl Assembly
614 Coupling Sub/Motor 2218 416SS A582M-95b
660 Bowl-Shaft 2227 416SS A582M-95b
661 Bearing – Discharge 1109 Bronze C90300 "G" Modified B584-00
670 Bowl - Intermediate 6911 Cast Iron CL30 Enamel A48-94e1
671 Sub Adapter 1018 Ductile Iron 65-45-12 B148-97e1
672 Bearing - Int Bowl 1109 Bronze C90300 "G" Modified B584-00
673 Impeller 1203 316SS A744M-00
677 Collet - Impeller 2242 Carbon steel A108-99
680 Wear Ring - Bowl N/A None N/A
681 Wear Ring - Impeller N/A None N/A
690 Bearing-Suction 1109 Bronze C90300 "G" Modified B584-00
- - - - -
715 Guard-Cable 3215 304SS A240M-00
758 Capscrew-Hex (Mot) 2228 304SS A276
760 Capscrew-Hex 2298 Steel Bolting Gr8 J429-99
781 Screen-Suction 3211 316SS A240M-00
789 Washer - Upthrust 6266 TIVAR 1000 N/A

DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

Certified by
Date of certification
Pump serial number
Project Name
Tag
 PERFORMANCE CURVE
Quote Number: 9001-170718-118:1
Model: VIS-WF
Size: 7CLC 8 Stage(s)

Driver Size Criteria: Max power on design curve (NOL) Best Efficiency: 81.10 %
Speed: 3550 RPM Flow at BEP: 364.00 USGPM
Impeller Trim: 5.125 inch Min Flow: 91.00 USGPM
Additional Impeller Trim: 5.1250 inch Derate Factor: 1.0000
Frequency: 60 Hz Specified NPSH Avail: 34.00 ft
Impeller Maximum Trim: 5.250 inch NPSH Required: 16.20 ft
Specified Flow: 317.00 USGPM Shut-Off Head: 1068.00 ft
Specified Head: 817.000 ft Fluid Type: Water
Head at Design: 838.00 ft Temperature / Specifc Gravity: 70.00°F / 0.9999
Efficiency at Design: 80.10 % Viscosity: 0.9695 cP
Power at Design: 84 Hp Allowable Sphere Size: 0.56 inch
Flow on Design Trim @ Max Pwr: 508.00 USGPM Thrust K Factor: 3.50 lbs/ft
Max Power on Design Curve: 94.90 Hp Additional Thrust K Factor: 3.50 lbs/ft

DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

Certified by
Date of certification
Pump serial number
Project Name
Tag