A Specifications

Standard

Print Method
Table 11. Printing Specifications

T5204 T5304 T5206 T5306 T5208 T5308

Print Resolution (dpi) 203 300 203 300 203 300

Min. Dot Size (sq. in) .005 .0033 .005 .0033 .005 .0033
(.127 mm) (.083 mm) (.127 mm) (.083 mm) (.127 mm) (.083 mm)

Bar Code Modulus (mils)

Picket Fence 5 - 127 6.7 - 110 5 - 127 6.7 - 110 5 - 127 6.7 - 110
Ladder 10 -127 10 - 110 10 - 127 10 - 110 10 - 127 10 - 110

Max. Print Speed (ips) 10 8 10 8 8 6

Max. Print Width (in.) 4.1 4.1 6.6 6.6 8.5 8.5
(104.1 mm) (104.1 mm) (167.6 mm) (167.6 mm) (215.9 mm) (215.9 mm)

Flash Memory (MB) 4 4 4 4 4 4

DRAM (MB) 8 8 8 8 8 8

Max. Print Length with stan- 46 21 75 35 59 27

dard memory (in.)(1) (1168 mm) (533 mm) (1905 mm) (889 mm) (1499 mm) (686 mm)

Max. Print Length with 16MB 99 99 99 99 99 99

memory expansion (in.)

NOTES:
1. These figures are approximate and depend upon the active emulation.

221
Appendix A

Media

General

Type: Roll-fed, die-cut continuous or fanfold labels, tags

or tickets; most direct thermal or thermal transfer
materials.
Supply Roll: 8 in (203 mm) maximum diameter on 1.5"
(37.5mm) to 3” (76 mm) diameter cores.
Internal Rewinder: Accepts a 5 inch diameter roll of label backing.
Label Material: Thermal transfer plain-coated papers, vinyl, Mylar,
metallized paper, non-woven fabric, fine woven
fabric, thermal-visible light scannable paper, infra-
red scannable paper, thermal ticket/tag stock, ther-
mally sensitive plastic stock.
Media Sensing: Moveable “see-through” for die-cut labels and
reflective for tags with black striping.
The printer uses a movable sensor to detect index
holes/notches or the black stripe in tag stock. The
sensor position is indicated by the notch on the top
of the sensor assembly.
Label Taken Sensor: Detects when a printed label is at the printer exit
throat.
Automatic Label Peels and presents label to the operator, one at a
Peel-Off: time.

222
 I. Tag Specification II. Tag Sepcification III. Label Specification
(Reflective Sensing) (Transmissive Sensing) (Transmissive Sensing)

Black Mark (on reverse side)

Suggested Cross Suggested Cross D

Perf Location D Perf Location

A
I B
A A

Direction Of Media Motion Direction Of Media Motion Direction Of Media Motion

Figure 9. Media Dimensions

Dimensions
Table 12. Media Specifications

T5X04 T5X06 T5X08

A Label Width Range 0.75 -4.5 in. 2.0-6.8 in. 3.0-8.75 in.
19.1-114.3 mm 50.8-172.7 mm 76.2-222.3 mm

B Backing Width Range 0.75-4.5 in. 2.0-6.8 in. 3.0-8.75 in.

19.1-114.3 mm 19.1-114.3 mm 19.1-114.3 mm

C Min. Gap/Hole/Notch Height 0.10 in. 0.10 in. 0.10 in.

2.54 mm 2.54 mm 2.54 mm

K Min. Refl. Mark Height 0.10 in. 0.10 in. 0.10 in.
2.54 mm 2.54 mm 2.54 mm

I Min Refl. Mark Width 0.5 in. 0.5 in. 0.5 in.
12.7 mm 12.7 mm 12.7 mm

E Media Thickness Range .0025-.01 in. .0025-.01 in. .0025-.01 in.

.0635-.254 mm .0635-.254 mm .0635-.254 mm

G Width of Inter-label gap/hole 0.25-0.50 in. 0.25-0.50 in. 0.25-0.50 in.

6.35-12.7 mm 6.35-12.7 mm 6.35-12.7 mm

D Media Length Range

Continuous/Batch Mode 0.25 in. (6.35mm) - 99 in. (2515mm)*

Tear-Off Strip Mode 0.25 in. (6.35mm) - 99 in. (2515mm)*

Tear Off Mode 1 in. minimum (25.4 mm) - 99 in. (2515 mm)*

Peel Off Mode 1 in. minimum (25.4 mm) - 99 in. (2515 mm)*

Cut Mode 2 in. minimum (50.8 mm) - 99 in. (2515 mm)*

These figures are approximate and depend upon the active emulation and application. Minimum values
may vary depending upon the selected media handling mode.
* 99 in. requires DRAM upgrade

223
Appendix A

Ribbon
Table 13. Ribbon Specifications

T5X04 T5X06 T5X08

Ribbon Width Range 0.75-4.5 in. 2.0-6.8 in. 3.0-8.75 in.
19 -114.3 mm 50.8-172.7 mm 76.2-222.25 mm
Max. Ribbon Length (m) 625 625 625

Indicators and Switches

Indicator Lights: ONLINE

Switches: POWER
Keys: PAUSE, JOB SELECT/ - (Decrement),
..
FEED/↑ (Up), TEST PRINT, . (Menu), û
(Cancel)/↓ (Down), ↵ (Enter)
Message Display: 2-row 16-characters per row for error mes-
sages, print status, and recalling stored
formats

Memory

Flash Memory (standard) 4MB SIMM installed on Controller PCBA

DRAM 8MB

224
Host Interfaces

1. Serial RS-232 or RS-422 at 600, 1200, 2400, 4800, 9600, 19200,

38400, 57600, or 115200 baud.
2. Parallel (Centronics compatible) or IEEE 1284 bi-directional.
The RS-232 and RS-422 host interfaces shall have the following
characteristics:
Character Set: ANSI® ASCII character set
Word Length: Selectable 7-bit or 8-bit data format
Handshaking: XON/XOFF (in receive mode only) and CTS/
DTR
Input Buffer: Selectable from 1k through 16 kbytes. XOFF is
transmitted and DTR goes low when buffer is
equal to or less than 25% of full. XON is
transmitted and DTR goes high when buffer is
25% above empty. Characters are transmitted
with no parity from the printer

Power

Power Source: 115 or 230 VAC 50/60Hz switching power sup-

ply.
Grounding: Unit must be connected to a properly grounded
receptacle.

Environmental

Operating Temperature: 41° F to 104° F (5° C to 40° C)

Storage Temperature: -40° F to 150° F (-40° C to 60° C)
Operating Humidity: 20% to 85%, non-condensing
Storage Humidity: 5% to 85% non-condensing
Ventilation: Free air movement
Dust: Non-conducting, non-corrosive

225
Appendix A

Physical

T5X04 T5X06 T5X08

Outside Dimensions (in.) 13H x 11.7W x 20.5D 13H x 13.4W x 20.5D 13H x 15.4W x 20.5D

Max. Weight (lbs/kg) 39 lbs. 45 lbs. 48.5 lbs.

17.55 kg 20.25 kg 21.83 kg
Add 1.75" D with media guide installed
Add 7.5" D and 6" H for validator option
Add 1.4" D for mdia cutter option

Acoustic Specifications

Table 14. 4400 Acoustic Noise Levels per ISO 9296

4400 @ 6 ips 4400 @ 8 ips

Printing: 62 dBA 63 dBA
7.4 Bel 7.9 Bel
Standby: 37 dBA 37 dBA
5.2 Bel 5.2 Bel
Geraeuschemission
nach ISO 9296
Druckend: 62 dBA 63 dBA
7.4 Bel 7.9 Bel
Betriebsbereit: 37 dBA 37 dBA
5.2 Bel 5.2 Bel

226