DI-M9305

Digital Single Riser Output Module

Features
Fire Alarm
 During normal standby, Output port (O1, O2) is Equipment
provided with Class B pathway supervision 47AU

when connects with 47KΩ EOLR (Part Number

30108524).
 Occupying one address. It can be modified in
filed.
 Output port utilizes AD sampling technology for
precise testing.
 Guide rail for installation, easy for construction.
 Compatible with GST-M200 and GST-IFP4M Fire
Alarm Control Panels (FACP).
 Standard: UL864, NFPA [70, 72].
Installation
Description
Warning:
With a microprocessor, DI-M9305 Digital Single
Riser Output Module can communicate with a FACP. Before installing the module, disconnect
power from the loop and verify that the
The module is designed to switch on/off 24VDC
guide rail is securely installed.
power at its output.

Connection and Cabling 1) Before installation, make sure the enclosure is

in good condition and markings are complete.
Fig. 1 shows terminals on the module.
2) The module shall either be installed in a North
America standard metal electrical box.
Minimum size is 4 in. square, 2-1/8 in depth (in
this case, standard box cover is required), or in
a UL Signaling Listed enclosure that provides
minimum wiring entries and spacing as shown
on Fig 2 and Fig 3. Minimum mounting space is
67×40.5mm.
3) The module can be mounted on a guide rail as
shown on Fig 4.
4) The module can also be installed in the
enclosure by 4 mounting screws as shown in
Fig.5.

Fig. 1
(Z1, Z2) IN & OUT: Connecting with loop of FACP,
polarity-insensitive.
(I1, I2) IN & OUT: Power input terminals. For
connecting with 24VDC power from Listed FACP or
power supply.
O1, O2: Output terminals to 24VDC powered devices
CODE: connecting with P-9910B programmer.

Recommended Wiring
17 AWG or above fire cable for all terminals, and Fig. 2
subject to local codes.

30310200 Issue 1.06

 Application
The module is designed to switch on/off connection
between I1/I2 and O1/O2. The address can be
programmed in field through a P-9910B Hand Held
Programmer.
Programming Parameters:
In standby state of the programmer, pressing Fn and
then number 3, “—” (data waiting for programming)
will be popped up on the screen. Writing a parameter
and then pressing “Program”, a “P” will show on the
screen meaning the parameter is programmed.

Parameters used for O1/O2 setting includes:

1 No checking
Any other numbers(Default) Checking
The system connection is shown in Fig. 6.
Fig. 3

FACP
Z2
Z1

Z1 Z2
DI-M9305 Module
in out

I1 I2 I1 I2 O1 O2

Controlled Device 1
24VDC power line to next device

Controlled Device N
Fig. 4

47kΩ/1W End-of-line
Resistor

Fig. 6

Fig. 5

30310200 Issue 1.06

 Accessories and Tools
Specification
Model Name Remark
SLC Operating Loop: 24VDC
P-9910B Hand Held Order
Voltage (16VDC - 28VDC)
Power Limited Programmer separately
Power Supply Maximum 30VDC. RY-1W-47k±5％ End-of-Line Provided
voltage Power Limited Resistor
Power Output Regulated if Power Input is
voltage Listed Regulated 24VDC power Limited Warranty
supply
GST warrants that the product will be free of charge
Special Application, if Power
for repairing or replacing from defects in design,
Input is Special Application
materials and workmanship during the warranty period.
supplied by Listed compatible
This warranty shall not apply to any product that is
FACP.
found to have been improperly installed or used in any
Standby Current Loop≤ 0.26mA
way not in accordance with the instructions supplied
Action Current Loop≤ 0.5mA with the product. Anybody, including the agents,
Maximum Output 2A @ 30VDC,0.35PF distributors or employees, is not in the position to
Load amend the contents of this warranty. Please contact
Programming Electrically addressed, one your local distributor for products not covered by this
Method address within 1 - 242. warranty.
Feedback LED Illuminates red when the relay is
activated, turns off as loop power
cuts down and flashes in other
states.
Fault LED Flashes yellow 0.5s on and 0.5s
off when output fault occurs. The
LED is quiet in other states.
Ingress Protection IP30 (not tested by UL)
Rating
Operating 0℃ - +49℃
Temperature
Relative Humidity ≤ 93%, Non Condensing
Material and Color ABS, white (RAL 9016)
of Enclosure
Dimension 85.3mm×78mm×33mm
(L×W×H) (with base)
Weight About 66.6g (with base)

This Data Sheet is subject to change without notice. Please contact GST for more information or questions.

Gulf Security Technology Co., Ltd.

No. 80, Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
Tel: +86 (0) 335 8502434 Fax: +86 (0) 335 8502532
[email protected] www.gst.com.cn
30310200 Issue 1.06