1

UNIT- I

SOURCES OF BIOELECTRIC POTENTIAL

The body generates their own monitoring signals which
convey useful information about the function they represent. These
signals are the bioelectric potential. Bioelectric potential are actually
ionic voltage produced as a result of electrochemical activity of
certain special type of cells.
Resting and Action Potential
The concentration of sodium ions inside the cell becomes
much lower than outside. Since the sodium ions are positive, the
outside of the cell is more positive than inside.
To balance the electric charge, potassium ions which are
positive enters the cell causing a higher concentration of potassium
on inside than on outside.

Fig 1.1: Polarized cell with its resting potential

This charge cannot be achieved. However Equilibrium is

reached with a potential difference across the membrane, negative on
inside and positive on outside. This membrane potential is called the
resting potential of the cell.
 2

Characteristics of Resulting Potential

The resting potential is maintained as a constant until some
kind of disturbance upsets the equilibrium. It is strongly depending
on temperature. It is given as negative and various from 60 to 100mA.
The resting potential ‗V‘of a cell can be written as

Where k – Boltzmann‘s constant

T- Absolute Temperature of
cell q- Change of electron
Pk, PNa, PCl- Permeability of K, Na, & Cl ions
+ -
[K ], [Na+], [Cl ] –Concentration of K, Na & Cl ions

Fig 1.2: Depolarized cell with action potential

When the passage of sodium ions is stopped, there is no ionic
current and hence the membrane reverts back to the original
condition. By an active process called a sodium pump, sodium ions
are quickly transported to the outside of cell and the cell is in its
resting potential. This is called repolarization.

Fig 1.3: waveform of the action potential

 3

The net height of action potential is defined as the

difference between the potential of depolarized membrane at the peak
of action potential and resting potential. Following the action
potential, there is a brief period of time during which the cell cannot
respond to any new stimulus.

ELECTRODES
Electrodes are used to pick up the electrical signals of the
body. They transfer the bioelectric event to the amplifier. The type
 10

of electrode to be used depends upon the bioelectric generator.

Half Cell Potential (or) Electrode Potential:
The voltage development at an electrode – electrolyte
interface is designated as the half cell potential. In metal solution
interface, an electrode potential results from two processes.
1. The passage of ions from metal into solution
2. The combination of metallic ions in solution with
electrons in metal to from atoms of metal.
The net result is the creation of charge gradient, the spatial
arrangement of which is called the electrical double layer. Electrodes in
which no net transfer of charge occurs across the metal electrolyte
interface are called as perfectly polarized electrodes.
Fig shows the electrical equivalent circuit of a surface
electrode when it is in contact with body surface. The electrode-
electrolyte interface resemble a voltage source having half cell
potential ‗Ehc‘which is developed due to charge gradient and a
capacitor ‗Cd‘(i) parallel with a leakage resistance ‗Rd‘.

Fig 1.12: surface electrode equivalent circuit

Cd – electrode capacitance
Rd – leakage resistance
Rs – Series electrolyte and skin resistance
The series resistance ‗Rs‘represents the series electrolyte
and skin resistance under equilibrium conditions. The impedance of
the equivalent circuit can be written as
= Rd
Z Rs
1 - j2 fC d Rd
The value of voltage and impedance depend on the

11
electrode metal, its area, electrolyte, charge density and frequency of
current. The electrode potential is measured with reference to
hydrogen electrode placed in electrolyte near metallic electrode. The
half cell potential development can be expressed by Nernst equation
as
RT C f
E= ln 1. 1

C f
nF 2 2
Where R – Gas Constant
T – Absolute Temperature
F – Faraday Constant
N – Valency of Ion
C1, C2 – Concentration of selected ion on two sides of
membrane
f1, f2 – Activity coefficients of ion on two sides of
membrane.
Purpose of Electrode paste:
The outer skin of the body is highly non- conductive and will
not establish a good electrical contact with an electrode. The skin
should be washed and rubbed to remove some of the outer cells. The
electrode paste decreases the impedance of contact and also reduces
the artifacts resulting from movement of electrode.
Electrode Material:
The electrode, electrode paste and body fluids can produce
a battery like action causing ions to accumulate on the electrodes.
This polarization of electrode can affect the signal transfer.
Types of Electrodes:
These are three types of electrodes
Micro electrodes (Intracellular Electrodes):
These are used to increase the bioelectric potential within a
single. It is divided into metallic and non metallic. The
microelectrodes should have smaller diameter and during insertion
of electrode into the cell, there will not be any damage to the cells.
 They are formed by electrolytically electing the tip of a fine
tungsten or stainless steel wire to a fine point. This technique is
known as electro pointing. The metal microelectrodes are coated
almost to the micro tip with a material.

Fig 1.13: Metal Microelectrode [Source: Leslie Cromwell - Biomedical

instrumentation and measurement]
The impedance of microelectrode tip is inversely
proportional to the area of the tip and frequency. When the electrode
output is couple with an amplifier, the low frequency components of
the bioelectric potentials will be attenuated if the input impedance of
the amplifier is not high.
ii) Micropipet
It consists of a glass micropipet tips diameter is about1
micrometer. The micropipette is filled with an electrolyte usually 3M
Kcl which is compatible with the cellular fluids.
EA is the potential between metal wire and electrolyte filled in the
micropipette
 Medical Electronics 13

EB is the potential between the reference electrode and the

extracellular fluid.
E is variable membrane potential
ED potential existing at the tip due to different electrolytes
present in the pipet and the cell
E = EA+EB+ED

Fig 1.14:Micropipet [Source: Leslie Cromwell - Biomedical

instrumentation and measurement]
Depth and Needle Electrodes
These are used to measure the bioelectric potentials of the
highly localized extracellular regions in brain or bioelectric potentials
from specific group of muscles.
i) Depth Electrode
These are used for study the electrical activity of the
neutrons in superficial layers of the brain. Normally each electrode
consists of a bundle of Teflon insulated platinum (90%) iridium
(10%) alloy wires, bonded to a central supporting stainless steel wire
which can act as indifferent electrode by an insulating varnish.
ii) Needle electrode
 14

These are used to record the peripheral nerve‘s action

potentials (Electro neurography). The needle electrode resembles a
medium dropper or hypodermic needle.
Surface Electrode
Generally large area surface electrodes are used to sense
ECG potentials and smaller area surface electrodes are used to sense
EEG and EMG potentials.
i) Metal plate Electrodes
Rectangular and circular plates from German silver, nickel
silver or nickel plated steel are used as surface electrodes in the case
of ECG measurement.

Fig 1.15: Metal plate Electrodes [Source: Leslie

Cromwell - Biomedical instrumentation and measurement]
ii)Suction Cup Electrode
It is more practical and is well suited for attachment to flat
surfaces of the body and to regions where the underlying tissue is soft.
Although physically larger this electrode has a small area because
only the rim is in contact with the skin.

Fig 1.16: Suction Cup electrode [Source: Leslie Cromwell - Biomedical

instrumentation and measurement]
iii) Adhesive Tape Electrode
The pressure of the surface electrode against the skin may
square the electrode pasted. To avoid this problem, adhesive tape
electrode is used.
Medical Electronics 15

Fig 1.17: Adhesive tape electrode [Source: Leslie Cromwell - Biomedical

instrumentation and measurement]
iv) Multipoint Electrode
It is a very practical electrode for ECG measurements and it
contains nearly 1000 fine active contact points. By this a low
resistance contact is established with the subject.
v) Floating electrode
Here, the metal does not contact the subject directly. The
contact is made via an electrolytic bridge. By means of this electrode,
movement artifact is eliminated. This is also called as liquid junction
electrode.
BOIPOTENTIAL RECORDERS
The bio – potential recorder plays an important role in the
biomedical instrumentation. ach doctor is performing his diagnosis
based on the output from recorder.
Characteristics of Recording System:
Sensitivity: The sensitivity is the magnitude of input voltage
required to produce a standard deflection in the recorded trace.
Linear: a recorder is said to be linear if the pen deflection is
proportional to the amplitude of input signal.
Frequency Response: A recorder is said to have good frequency
response when the sensitivity is constant for all the frequencies
present in the signal.

ELECTRO CARDIO GRAPHY (ECG)

ECG deals with the study of electrical activity of heart
muscles. Electrocardiogram is the recorded ECG wave. ECG is also
called EKG is derived from the German Electro Kardio Gam.
i) Origin of Cardiac action potential:
Heart is divided into four chambers. The top two champers are atria
and lower two champers are ventricles.
 16

Fig 1.18: Cross Section of the Interior of the Heart

Table 1.1Physiological Nature of ECG Waveform
[Source: Leslie Cromwell - Biomedical
instrumentation and measurement]

Origin Amplitude Duration sec

mV
Atrial depolarization or 0.12 to o.22
P Wave
contraction (P-R interval)
Repolarisation of the atrial and the 1.60 0.07 to 0.1
R wave depolarization of theventricles

Ventricular repolarisation 0.1 to 0.5 0.05 to 0.15

(Relaxation of (S-T interval)
myocardium)
S-T Ventricular contraction
interval
U wave Slow repolarisation of the < 0.1 0.2 (T-U interval)
intraventricular (Purkinje fibers)
system
 The complete waveform is called electrocardiogram
indicating important diagnostic features. If PR interval is more than
0.22 sec, AV (first heart attack) occurs. When QRS duration is more
than 0.1 sec, the bundle block (severe heart attack) occurs.
(ii) Lead configuration
The electrode systems are
1) Bipolar limp leads (or) standard leads.
2) Augment unipolar limp leads.
3) Chest leads (or) precordial leads.
4) Frank lead system (or) corrected orthogonal leads.

1) Bipolar Limb leads – Standard leads I, II, and II

In standard leads, the potential are tapped from four locations of our
body. They are i) right arm ii) Left arm iii) Right Leg and iv) Left
leg.
Right leg electrode is acting as ground reference electrode.
Fig.1.20 shows the standard bipolar limp lead positions and the
corresponding wave patterns.
Lead I position – give voltage VI, the voltage drop from left arm(LA)
to right arm (RA)
Lead II position- gives voltage VII, voltage drop from left leg (LL) to
right arm (RA)
Lead III position – gives voltage VIII, voltage drop from left leg (LL)to
left arm (LA)

Fig 1.20: Standard Bipolar Limb Leads and the Corresponding

ECG [Source: Leslie Cromwell - Biomedical instrumentation and
measurement]
 Fig 1.21: Einthoven Triangle
[Source: Leslie Cromwell - Biomedical instrumentation and measurement]18

The closed path RA to LA to LL and back to RA is called

the Einthoven triangle. Along the sides of this triangle, three
projections of ECG vector are measured.
2) Augmented unipolar Limb leads
In this, the electrocardiogram is recorded between a
exploratory electrode and the central terminal.

Fig.1.22: Augmented Unipolar Limb Leads [Source: Leslie Cromwell -

Biomedical instrumentation and measurement]

3) Unipolar Chest Leads

In this, exploratory electrode is obtained from one of the
chest electrodes. The chest electrodes are placed on six different
points on chest closed to the heart. By connecting three equal large
resistances to LA, RA and LL a reference electrode or central terminal
is obtained. This lead system is known as Wilson system.
Electrocardiogram recorded from these 12 lead selections such that 3
standard bipolar leads, 3 augmented unipolar leads and 6 chest leads.
Medical Electronics 19

Fig.1.23: Unipolar Chest Leads [Source: Leslie Cromwell - Biomedical

instrumentation and measurement]
The ECG potentials are measured with colour coded leads
for easy reference.
4) Frank lead system:
The corrected orthogonal lead system (or) Frank lead system
is used in vector cardiography. Here one can get the information from
12 leads. The state of the heart is studied three dimensionally.
ii) ECG Recording setup:
i) Patient cable and Defibrillator Protection Circuit
The patient cable connects the different leads from the limbs
and chest to the defibrillator protection circuit. It consists of buffer
amplifiers and over voltage protection circuit. Each patient lead is
connected to one buffer amplifier.
ii) Lead selector switch
It is used to feed the input voltage from appropriate electrode
to the preamplifier.
iii) Calibrator
A push button allows a standardization voltage of 1 mV to
the preamplifier. This enables to observe the output on display unit.
From lead selector switch, ECG signal goes to bio-amplifier.
 20

Fig1.24: ECG Recording [Source: Leslie Cromwell - Biomedical

instrumentation and measurement]
Setup iv) Bio-Amplifier
The bio-amplifier consists of a preamplifier and power
amplifier. The preamplifier should have high gain and high CMRR.
It consists of two power transistor such that their emitters are
joined together and connected with RL. When VB is positive, Q1 is FB and
conducts while Q2 is RB a nd remains off.
2
Output power pout = V out / RL

Amplifier efficiency η = Pout / (pout +Ploss )

To avoid the cross over distortion, an ideal non – inverting
amplifier is inserted at the output. Since Rf is so large, it raise the
gain and output voltage and thereby crossover distortion is
eliminated. The effect control is provided by R2 and gain adjustment
Medical Electronics 21

is provided by Rs.

Fig.1.25: Push-Pull Power Amplifier with Crossover

Compensation and Offset Control [Source:
Leslie Cromwell - Biomedical instrumentation
and measurement]
v) Auxiliary Amplifier
The common mode signals can be reduced to a minimum
level by adding an auxiliary amplifier between right leg lead and ECG
unit.
vi) Isolation Tower Supply
It is used given power to the bio amplifier and hence the
electrical safety for the patient is increased.
vii) Output Unit
In paper chart recorder, the power amplifier or pen amplifier
supplies the required power to drive pen motor. Pen motor records
the ECG trace on the wax coated heat paper. A position control is
used to position the pen at the center on the recording paper.
viii) Power switch
The power switch of the recorder has three positions. In ON
position the power to the amplifier is turned on. But the paper drive
is not running. In RUN position, the switch makes the paper drive to
run. In OFF position, ECG unit is in switched off condition. Analysis
of Recorded ECG Signals
 22

Fig. shows the analysis of different ECG signals.

Normal ECG

Here the PQ segment has prolonged conduction time i.e greater than
0.22second
Result: First degree AV block

Here QRS complex is widened i.e QRS interval is greater than 0.1
second
Result: Bundle block

Here ST segment is elevated

Result: Myocardial infraction
Medical Electronics 23

Here ST segment is depressed and negative T wave is present Result:

Coronary insufficiency

Here the train of pulses instead of PQRST waves

Result: Ventricular fibrillation which may lead to death if it is not
properly corrected by defibrillator.
If the normal conduction system is disturbed, then the beat
rate will be slower than the normal rate. This state s called heart block.
Vector cardiography
In electrocardiography, only the voltage generated by the
electrical activity of the heart is recorded. In vector cardiography, the
cardiac vector is displayed with its magnitude and spatial orientation.
Echocardiography
Echocardiography is a useful technique for diagnosis of
heart diseases.. By changing the position of transducer, we can get
reflections from the desired areas on the heart. An aqueous get is used
to couple the transducer to the skin and the beam from the transducer.
The time compensated signal amplifier is used to collect the low
amplitude signals with same signal to noise ratio. Then these
amplified signals are given to the cathode ray tube display unit.
A – Mode display
In amplitude mode or A - mode display, the echoes produce vertical
displacements of a horizontal trace on the screen. The amount of
vertical displacement is proportional to the strength of echo and the
distance along horizontal trace represents the time taken by
ultrasound to travel through tissue. Since the heart is moving,
 24

echoes dance up and down during cardiac cycle.

B – Mode display
In brightness mode or B – mode display, the echoes are
0
rotated through 90 towards the observer and so the echoes are
presented as dots of light. The distance between dots represents the
tissue depth. When echoes are from moving structure, dot‘s of light
move back and forth.

Fig.1.26: Block diagram of Echocardiograph and the

typical Echocardiograms M – Mode display
[Source: Leslie Cromwell - Biomedical
instrumentation and measurement]
In time – motion mode or m – mode Display, B – mode echo
signal is recorded either by sweeping the oscilloscope screen or
photographing the oscilloscope face on moving paper. In the
conventional m – mode display time is on the x – axis distance on y
– axis and intensity of echo is on z – axis
In echocardiogram the hill and valley regions indicate the
working heart. A rapid b – mode scan of heart is known as real time
Medical Electronics 25

scan which is also called cross sectional or 2- D echocardiography.

PHONOCARDIOGRAPHY (PCG):
The graphic record of the heart sounds is called
―Phonogram. Since the sound is from the heart, it is called
phonocardiogram. The instrument used to measure the heart sounds
is called phonocardiograph.
1) Heart sounds
2) Murmurs
Heart sounds have a transient character and are of short duration.
Heart murmurs have a noisy characteristic and last for a longer time.
Heart sounds are due to the closing and opening of valves whereas
murmurs are due to turbulent flow of blood in the heart and large
vessels.
Heart sounds
Heart sounds are classified into four groups based on their
origin. They are
1) Valve closure sounds
2) Ventricular Filling sounds
3) Valve opening Sounds
4) Extra cardiac sounds
1) Valve Closure Sounds
The sounds occur at the beginning of systole (First heart
sound) and the beginning of diastole (Second heart sound). The first
heart sound is due to the closure of mitral and tricuspid valves. The
second heart sound is due to the closure of aortic and pulmonary
valves.
2) Ventricular filling sounds.
These sounds occur either at the period of rapid filling of the
ventricles (Third heart sounds) or during the terminal phase of
ventricular filling (ie) atrial contraction. These sounds are normally
in audible.
3) Valve opening sounds
They occur at the time of opening of atrio – ventricular
valves and semilunar valves.
4) Extra cardiac sounds
 26

They occur in mid (or) late systole (or) early diastole. They
are caused by thickened pericardium which limites ventricular
distensibility.
Physical characteristics of sound
Heart sounds and murmurs are characterized by three
physical properties. They are
1) Frequency
2) Amplitude
3) Quality
1) Frequency: All heart sounds and murmurs are made up of
frequencies between 10 and 1000 Hz. They are divided into low,
medium and high- pitch frequencies
i) Low range: 10 – 60 Hz. It is represented by the third and
fourth heart sounds.
ii) Medium range: 60 – 150 Hz. It is represented by the first
and second heart sounds.
iii) High range: 150 – 1000 Hz. It is represented by snaps,
clicks and diastolic murmurs of aortic and pulmonary insufficiency.
1) Amplitude: Low frequency heart sounds have the biggest
amplitude while the high frequency murmurs have small amplitudes.
2) Quality: quality depends upon the overtones (or) harmonics
accompanying the fundamental frequency and applies to tones.
Origin of the heart sounds.
There are four separate heart sounds that occur during
the sequence of one complete cardiac cycle.
1) First heart sound: It is produced by a sudden closure of mitral
and tricuspid valves associated with myocardial contraction.
a) Timing: The low frequency vibrations occur approximately
0.05 sec after the onset of QRS complex of ECG.
b) Duration: It lasts for 0.1 to 0.12 sec.
c) Frequency : The first heart sound range from 30 – 50 Hz
d) Asculatory area: The first heart sound is best heard at the
apex of the mid pericardium.
2) Second heart sound: It is due to the closure of semi lunar valves
Medical Electronics 27

(ie) the closure of aortic and pulmonary valves

a) Timing: The second heart sound start approximately 0.03 –
0.05 sec after the end of ‗T‘wave of ECG.
b) Duration : 0.08 – 0.14 sec
c) Frequency : 250 Hz
d) Asculatory Area: It is best heard in the aortic and
pulmonary areas.
3) Third heart sound: It arises as the ventricles relax and the
internal pressure drops well below the pressure in atrium.
a) Timing: It starts at 0.12 – 0.18 sec after onset of second
heart sound.
b) Duration : 0.04 – 0.08 sec
c) Frequency : 10 – 100 Hz
d) Asculatory Area: It is best heard at the apex and left lateral
position after lifting the legs.
4) Fourth heart sound: Also called as atrial sound. It is caused by
an accelerated flow of blood into the ventricles or due to atrial
contraction. It occurs immediately before the first heart sound.
a) Timing : it starts at 0.12-0.18 sec after the onset of p-wave
b) Duration :0.03-0.06 sec
c) Frequency :10-50 Hz
d) Ausculatory Area: Because of its low frequency, it is
inaudible
Heart murmurs
Murmurs are sounds related to non – laminar flow of
blood in the heart and the great vessels.

They are distinguished from heart sounds such that

1) They have noisy character.
2) They have longer duration
3) They are high frequency components upto 1000 Hz.
Typical conditions in cardiovascular system which cause turbulence
in blood flow.
1) Local obstructions to blood flow
2) Abrupt change in blood stream diameter.
3) Pathologic communication in cardiovascular system
 4) Ruptured cardiac structures.
5) Valve insufficiency.
Transduction of heart sound
The sounds and murmurs originate from the heart which
can be picked up from the chest using a stethoscope or by
transduction of sound into electrical signals. The heart sounds are
conducted from the heart to the cheat.
Recording setup:
The heart sounds are converted into electrical signals by
means of a heart microphone. The electrical signals from microphone
are amplified by a phonocardiographic preamplifier followed by
suitable filters and recorder.

Fig.1.27: Block diagram of recording setup [Source: Leslie Cromwell -

Biomedical instrumentation and measurement]
The electrodes are placed on the limbs to pickup the
electrical activity of heart and these signals are amplified and
recorded. This recorded ECG is used as a reference for PCG.

Fig1.28: Placement of Microphone on Different Areas of

the chest for Recording PCG Heart Sound Microphone
[Source: Leslie Cromwell - Biomedical instrumentation
and measurement]
Medical Electronics 29

The conversion of heart sounds into electrical signals can be

done using transducers. Via condenser microphone, moving coil
microphone etc. The two main categories of microphones used in P
G are
1) The air coupled microphone
2) The contact microphone.
In the first case, the movement of chest is transferred via
on air cushion and presents low mechanical impedance to chest.
C = Q/V
The vibrations produced by chest wall change the position
of diaphragm which results in the change in voltage across
electrode. The developed dc voltage is in the order of few mV.
Relationship between heart and function of cardiovascular system

Fig 1.29: Condenser Microphone along with its Circuit [Source:

Leslie Cromwell - Biomedical instrumentation and measurement]

Fig 1.30: ECG waveform vs PCG [Source: Leslie

Cromwell - Biomedical instrumentation and measurement]
waveform Medical Applications
Rheumatic Valvular Lesions
Valvular lesions results from rheumatic fever. Rheumatic
 30

fever is an allergic disease in which heart valves are damaged.

This can be detected by phonocardiograph.
Fig (a) shows the normal heart sounds
The valvular lesions cause the abnormal heart sounds as
given below
1) The murmur of aortic steonosis
2) The murmur of aortic regurgitation
3) The murmur of mitral regurgitation
4) The murmur of mitral stenosis
Special applications of phonocardiogram
1) Fetal phonocardiogram
2) Esophageal phonocardiogram
3) Tracheal phonocardiogram
ELECTRO ENCEPHALO GRAPHY (EEG)
EEG deals with the recording and study of electrical activity
of brain. The brain waves can be picked up and recorded by means of
electrode attached to the skill of a patient. Brain waves are the
summation of neural depolarization in the brain due to stimuli from
five sense and thought process.
1) Anatomy of brain
The brain consists of three major parts such as cerebrum,
cerebellum and the brain stem.

Fig 1.31: Internal structure of Human brain [Source: Leslie

Cromwell - Biomedical instrumentation and measurement]
Medical Electronics 31

Cerebrum consists of two hemispheres and the hemispheres

are divided into frontal lobe, parietal lobe, occipital lobe and temporal
lobe.

Fig 1.32: Human Brain [Source: Leslie Cromwell - Biomedical

instrumentation and measurement]
2) Action Potentials of Brain:
When the propagated action potential reaches the cell, the cell fires
and thus a spike wave is produced. This firing spreads throughout the
dendritic branches and causes the release of transmitter substances.
Inhibitory Post Synaptic Potential ( PSP)
If the transmitter substance is inhibitory, membrane
potential of receptor neuron increases in a negative direction. It is less
likely to discharge; this induced potential charge is called an IPSP.
Excitatory Post Synaptic Potential (EPSP)
If the transmitter substance is excitatory, receptor membrane
potential increases in a positive direction.
Evoked potentials
Evoked potential are the potentials developed in the brain as
the responses to external stimuli like sound, light etc..
3) Brain waves
Brain waves are the recorded electrical potentials on the
surface of brain. The intensity and patterns of electrical activity are
determined by the overall level of excitation of brain.
 Fig 1.33: Brain Waves [Source: Leslie Cromwell - Biomedical
instrumentation and measurement]
Alpha waves
Frequency: 8 – 13 Hz
Occurrence: They found in normal persons when they are awake in a
quiet, state. They occur normally in occipital region. During step,
these disappear
Beta waves
Frequency: 13 – 30 Hz
Occurrence: These are recorded from parietal and frontal regions
of scalp two types: - Beta I – Inhibited by cerebral activity
Beta II – Excited by mental activity (tension)
Theta waves
Frequency: 4 – 8 Hz
Occurrence: These are recorded from parietal and temporal regions of
scalp of children.
Delta waves
Frequency: 0.5-4Hz
Occurrence: These occur only in every 2 or 3 sec. These occur in deep
Medical Electronics 33

sleep in premature babies and in very serious brain disease.

4) Placement of electrode
In EEG, electrodes are placed in standard positions on skill
in an arrangement called 10 – 20 system. The electrodes are arranged
as follows.
1) Draw a line on the skull from the nasion, the root of nose, to the
inion, ossification center on occipital lobe.
2) Draw a similar line from the left preauricular (ear) point to the right
preauricular point.
3) Mark the intersection of two lines as Cz which is the midpoint of
distance nasion and inion.
4) Mark points Fpz, Fz, Cz, Pz and Oz at 10, 20, 20, 20, and 10% of
total nasion – inion distance.
5) Mark points T3, C3, Cz, C4, and T4 at 10, 20, 20, 20 and 10%
of total distance between preauricular points.
6) Measure the distance between Fpz and Oz along the circle
passing through T3, and mark points as Fp1, F7, T3, T5, and O1 at
10, 20, 20, 20 and 10% of this distance.
7) Repeat this procedure on right side and mark the positions as Fp2,
F8, T4, T6, and O2.
8) Measure the distance between Fp1, and O1 along the circle
passing through C3 and mark point as F3, C3, and P3 at 25%
intervals.
9) Repeat this procedure on right side and mark as F4, C4 and P4.
10) Check that F7, F3, Fz,F4 and F8 are equidistant along transverse
circle passing through F7, Fz, and F8 check that T5, P3, Pz,P4, and T6,
a re equidistant along transverse circle passing through T5, Pz, &
T
6
Pg1 AND Pg2 are nasopharyngeal electrodes and A1 and
A2 are ear electrodes.
 34

Fig 1.34: Placement of lectrodes on the Scalp for the EEG Recording
[Source: Leslie Cromwell - Biomedical instrumentation and
measurement]
Pg1 AND Pg2 are nasopharyngeal electrodes and A1 and
A2 are ear electrodes. The electrode systems are used to facilitate the
location of foci, (ie) cortical areas from which abnormal waves
spread.
5) Recording Setup
In EEG recording setup, there are and drive amplifier whose
gain can be increased by cascading several stages. The patient cable
consists of 21 electrodes and is connected to the eight channel
selector. The electrodes are attached to the channel selector in groups
of eight called a montage of electrodes. The interference is reduced
by employing differential amplifiers as preamplifiers.
Medical Electronics 35

Fig 1.35: Fig: Modern EEG Unit [Source: Leslie Cromwell -

Biomedical instrumentation and measurement]

EEG unit is covered with ferrous metal screen to reduce a,c

interference.
The filter bank consists of appropriate filters to select
different types of brain waves. Visual stimulus, Audio stimulus and
tactile (touch) stimulus are used to record evoked potentials from
sensory parts of brain. The time delay between stimulus and response
can be measured in the signal processing unit.
6) Analysis of EEG
EEG helps physicians to diagnose the level of
 36

consciousness, sleep disorders, brain death, brain tumors, epilepsy

etc.
i) Level of consciousness
EEG changes with the level of consciousness. Diminished
mental activity results in a lower frequency and large amplitude EEG
wave.
REM means Rapid Eye Movement. REM sleep coincides
with the periods of dreaming. EEG displays the characteristic features
during the application of anaesthesia.
If the tumor displays the cortex and if it is large enough, the
electrical activity will be absent since no electric potentials originate
in the tumor. Thus a damped EEG over the cortex can be a sign of a
tumor.
Epilepsy
Epilepsy is a symptom for brain damage. It may due to
defects in birth delivery or head injury during accident or boxing. It
may also be due to brain tumor. Epilepsy is divided into two types.
Grandmal
Peritmal
Grandmal
Before grandmal attack, the patient recognizes a set of
symptoms such that he sees a flash of light if grandmal arises from
visual center .He hears a noise if it arises from acoustic center. It
extends from few sec to several min
Peritmal
In peritmal attack, spike type waves are produced with a
frequency 3 Hz. It lasts for 1– 20 sec.
Application
(i) Epilepsy – EEG is very helpful to find acuteness of
epilepsy.
(ii) Anesthetic level – It is helpful to find the depth of
intensity of anesthesia
(iii) Brain injury – If there is a scar on the cerebral cortex, it
creates irrigative effect on the nearby healthy cortex. It is
identified by EEG waveform.
Medical Electronics 37

(iv) Monitor during surgery – Doctor to find patient‘s

conditions.
(v) Effect of Yoga – Identified by EEG for a normal person
initially EEG in recorded.
The person has to do yoga for some time. After some period,
once again EEG recorded for same person. Then it is compared with
previous wave form different gives the effect of yoga.

ELECTRO MYO GRAPHY (EMG)

Electromyography is the science of recording and
interpreting the electrical activity of muscle‘s action potential. The
recording of peripheral nerve‘s action potentials is called
electroneurography.
Recording Setup
The surface electrodes or needle electrodes pickup the potentials
produced by the contracting muscle fibers. The surface of the skin
cleaned and electrode paste is applied.

Fig 1.36: Block Diagram for EMG Recording Setup [Source: Leslie
Cromwell - Biomedical instrumentation and measurement]
The needle electrode picks up the action potentials from
selected nerves or muscle. Further to record the action potentials from
a signal nerve, microelectrodes are used.
 The amplitude of EMG signals depends upon the type and placement of electrodes used.
Surface electrode picks up many overlapping spikes and produces an average voltage from
various muscles.
The amplifier should have uniform frequency response, high CMRR and high input
impedance. The signal is also recorded in the tape recorder for further reference.
Determination of conduction velocities in motor nerves.
The measurement of conduction velocity is used to indicate the location and type of
nerve lesion.
The EMG electrode and stimulating electrode are placed at
two points on the skin, separated by a known distance l1.An electrical pulse is applied through the
stimulating electrode. The latency is now
measured as ‗ t 2‘seconds. The conduction velocity is
U = l1- l2 / t 1 –t2
The conduction velocity in peripheral nerves is normally 50 m/s. when it is below 40 m/s, there
is some disorder in nerve conduction.

Fig 1.37: Determination of Conduction Velocity in a Motor Nerve

39