Scribd
Upload
68 views4 pages

DIY - Hand Gestures Controlled Car Using Arduino - NRf24l01 - MPU6050 - 4 Steps - Instructables

This document provides a guide for building a hand gesture-controlled car using Arduino, NRf24l01, and MPU6050. It includes a parts list, tools required, and steps for assembling the transmitter and receiver, as well as uploading the necessary code. Safety precautions regarding lithium-ion batteries are emphasized throughout the instructions.

Uploaded by

uppermedal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
68 views4 pages

DIY - Hand Gestures Controlled Car Using Arduino - NRf24l01 - MPU6050 - 4 Steps - Instructables

This document provides a guide for building a hand gesture-controlled car using Arduino, NRf24l01, and MPU6050. It includes a parts list, tools required, and steps for assembling the transmitter and receiver, as well as uploading the necessary code. Safety precautions regarding lithium-ion batteries are emphasized throughout the instructions.

Uploaded by

uppermedal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

DIY | Hand Gestures Controlled Car Using Arduino | NRf24l01 |

MPU6050
By ElectronicsisLife in CircuitsElectronics

Introduction: DIY | Hand Gestures Controlled Car Using Arduino |


NRf24l01 | MPU6050

Hand Gesture controlled car in like a Magic.


You can easily impress your Friends and Family with it. In this video we will learn How to build the
Remote car which can be Controlled using our hand Gestures.

While building the car please be careful with lithium ion batteries.

Step 1: Watch the Video


Please watch the video before building your own Car.
Step 2: Gather Required Parts

Parts List: (Amazon.in)


4wd Car kit : https://amzn.to/2R5F7rP

Arduino UNO : https://amzn.to/3o3lP2h

Arduino Nano : https://amzn.to/3o3lP2h

L298 Motor Driver : https://amzn.to/3o3lP2h

nRf24L01 Modules : https://amzn.to/3o3lP2h

Joystick : https://amzn.to/3o3lP2h

18650 Li-ion battery : https://amzn.to/3o3lP2h (If possible buy this from local shop)

18650 Li-ion battery charger : https://amzn.to/3uB7OLB

Battery Holders : https://amzn.to/3uB7OLB

Wires : https://amzn.to/3uB7OLB

General purpose PCB : https://amzn.to/3uB7OLB

20 mm berg strips : I bought this from local electronics shop

Scotch Tape : https://amzn.to/3uB7OLB

Switches : Local Shop

Tools Required:

Soldering Iron : https://amzn.to/3o4emjm


Iron I used : https://amzn.to/3o4emjm

Step 3: Build Transmitter and Receiver

With help of provide schematics build the Transmitter and Receiver.


Step 4: Install Required Libraries and Upload the Code . You Are
Ready to Go.

Please be careful with Lithium ion batteries.

You might also like