CARIBBEAN EXAMINATIONS COUNCIL

Caribbean Secondary Education Certificate®

TECHNICAL DRAWING
Specimen Paper s and
M ark Schemes/ Keys
Specimen Papers: - Paper 01
Paper 02 (Building Drawing)
Paper 02 (Mechanical Engineering Drawing)

Mark Schemes and Keys: - Paper 01

Paper 02 (Building Drawing)
Paper 02 (Mechanical Engineering Drawing)

77
 TEST CODE 01247010
SPEC 2015/01247010

CARIBBEAN EXAMINATIONS COUNCIL

CARIBBEAN SECONDARY EDUCATION CERTIFICATE

EXAMINATION

TECHNICAL DRAWING

Paper 01 – General Proficiency

75 minutes

READ THE FOLLOWING INSTRUCTIONS CAREFULLY.

1. This test consists of 60 items. You will have 75 minutes to answer them.

2. In addition to this test booklet, you should have an answer sheet.

3. Each item in this test has four suggested answers lettered (A), (B), (C), (D). Read each item you are
about to answer and decide which choice is best.

4. On your answer sheet, find the number which corresponds to your item and shade the space
having the same letter as the answer you have chosen. Look at the sample item below.

Sample Item

In drawings, thin short dashes represent Sample Answer

(A) adjacent parts A C D

(B) hidden details
(C) movable parts
(D) irregular details

The best answer to this item is “hidden details,” so (B) has been shaded.
5. If you want to change your answer, erase it completely before you fill in your new choice.

6. When you are told to begin, turn the page and work as quickly and as carefully as you can. If
you cannot answer an item, go on to the next one. You may return to that item later.
7. You may do any rough work in this booklet.
8. Figures are not necessarily drawn to scale.

DO NOT TURN THIS PAGE UNTIL YOU ARE TOLD TO DO SO.

Copyright © 2011 Caribbean Examinations Council

All rights reserved.

01247010/SPEC 2015
1. In an isometric sketch, circles and arcs will Item 4 refers to the following diagram.
appear as

(A) segments
(B) round, smooth lines 4. In the drawing above, which of the
(C) ellipses or part of ellipses following letters indicates the centre of the
(D) round arcs without distortions arc which is tangential to the two circles?

(A) M
2. Which of the following instruments is used (B) N
to draw irregular curves? (C) O
(D) R
(A) Compass
(B) Protractor
(C) Flexicurve Item 5 refers to the following views.
(D) Radius curve

5. Which of the views below shows the plan

3. Which of the following drawings shows of the object illustrated in the two views
triangles of equal area between parallel above?
lines?

01247010/SPEC 2015
 -3-

6. Which of the following correctly defines Item 8 refers to the following diagram.
the locus of a point?

(A) The calculated circumference

(B) A point which moves and traces
a path
(C) The cutting tool attached to the
lathe
(D) A right-angled triangle wrapped
around a cylinder

7. Which of the following circles is

correctly dimensioned?

Ø36 8. The polygon shown above is a regular

hexagon of side

(A) (A) 47.5 mm

(B) 50.5 mm
(C) 52.5 mm
(D) 55.5 mm

(B)
Item 9 refers to the following diagram.

36

(C)

R 18

(D) 9. The triangle illustrated above can be

constructed with the use of

(A) a ruler and pencil only

(B) a compass and protractor only
(C) a compass, a ruler and a pencil
(D) a set-square, a ruler and protractor

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -4-

10. Which of the following is a view of a Item 12 refers to the following diagram.
right triangular pyramid?

12. Which of the following represents the plan

of the drawing above?

11. Which of the following represents the 13. Which of the following patterns could be
correct procedure for bisecting an angle of folded to form a truncated square prism
90°? having no cover or base?

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -5-

14. Which of the following drawings shows a Item 16 refers to the following construction.
rectangle equal in area to a triangle?

16. The purpose of the construction above,

when completed, is to

(A) draw a tangent to the circle from A

(B) draw two tangents to the circle
from B
(C) draw an arc to pass through three
points
(D) find the mean proportional to AO
and CO
Item 15 refers to the following views.
Item 17 refers to the following diagram.

15. Which pictorial view below is

represented by the orthographic views
shown above?
F

17. In the diagram above, the angle EFH is

(A) 30°
(B) 45°
(C) 60°
(D) 90°

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -6-

18. A cube with an edge of 80 mm is to be 19. Which of the following is a true elevation
drawn in oblique projection. The length of of the drawing shown above?
the receding lines, in mm, should be

(A) 10
(B) 20
(C) 30
(D) 40

Item 19 refers to the following diagram.

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -7-

20. Which of the following illustrates the 22. Which of the following patterns can be
normal of an ellipse? folded to form a square prism with an
oblique top?

21. ‘The spiral of Archimedes’ is defined as

(A) a plane curve generated by a point

on a taut chord as it is unwound
from the perimeter of a polygon
(B) the path generated by a point which
revolves uniformly about a pole
and has a uniform motion away
from it
(C) a plane curve generated by the path
of a point on the perimeter of a
wheel as the wheel travels on a
straight track
(D) the path generated by a point
travelling in a place such that the
difference of its distance from two
foci is constant and equal to the
traverse axis

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -8-

Item 23 refers to the following diagram. Item 26 refers to the following diagram.

26. The type of projection illustrated above is

23. The diagram above illustrates
the construction of a (A) oblique
(B) first-angle
(A) circle tangential to two (C) isometric
converging lines (D) third-angle
(B) tangent from a point outside a
given circle
(C) circle tangential to two lines at Item 27 refers to the following construction.
right angles
(D) tangent to a circle at a point on
its circumference

Item 24 refers to the following diagram.

24. The construction used in designing the

bending jig illustrated above was that for 27. Which of the following is TRUE of the
obtaining a construction above?

(A) tangent joining two arcs (A) IJKF is half the area of EFGH.
(B) common internal tangent (B) EFGH is equal in area to IJKF.
(C) tangent to two equal circles (C) EFGH is half the area of IJKF.
(D) tangent from a point outside the (D) IJKF is twice the area of EFGH.
circle

28. The ANSI, BS and ISO regulations used in

25. The point at which the bisectors of the technical drawing are referred to as
angles of a triangle meet is the centre of
(A) local codes
(A) two given circles (B) building codes
(B) the escribed circle (C) regional standards
(C) the inscribed circle (D) international standards
(D) the common tangent

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -9-

29. When sketching pictorial figures, one Item 32 refers to the following diagram.
should first

(A) sketch circles

(B) draw all straight lines
(C) construct parts separately
(D) construct a box to hold the figure

30. Which of the following surfaces is

developed in the shape of a 'T' by unfolding
or unrolling?

(A) A square pyramid

(B) A triangular prism
(C) A rectangular box with lid
(D) A hexagonal truncated prism
32. The diagram above shows the method of
finding the centre of an arc, with radius R,
Item 31 refers to the which is tangential to
following construction.
(A) two straight lines meeting at right
angles
(B) two straight lines meeting at any
angle
(C) a line and a circle
(D) a straight line

Item 33 refers to the following diagram.

31. The construction above shows how to draw

a parallelogram equal in area to a given
triangle. If EF is 30, then X is

(A) 10
(B) 15
(C) 20
(D) 30

33. The diagram above is to be reproduced in

third angle projection. On what views can
the distance X be seen?

(A) Top and front

(B) Top and right side
(C) Front and left side
(D) Front and right side

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -10-

Item 34 refers to the following diagram. Item 36 refers to the following diagram.

34. The sides of the square QRST above are

bisected and the adjacent points are joined
to form another square. The area of the 36. In the ellipse above, which sum of
new square is distances is equal to AB?

(A) 72 mm2 (A) F1C + F2C

(B) 81 mm2 (B) AC + BC
(C) 162 mm2 (C) F2C + CD
(D) 324 mm2 (D) F1C + CB

Item 35 refers to the following diagram. 37. When designing a new product, which
type of drawing is usually made FIRST?

(A) Scale
(B) Sketch
(C) Detail
(D) Engineering

38. The centre of the circumscribing circle of a

triangle can be found by using the
35. In the diagram above, the circles and (A) three medians
curves are shown in their true shapes. The (B) bisectors of any two sides
method of projection used is (C) bisectors of any two angles
(D) perpendicular to any side and a
(A) oblique median
(B) trimetric
(C) isometric
(D) orthographic
39. In a perspective drawing, all vertical lines

(A) have vanishing points

(B) pierce the picture plane
(C) are toward the point of sight
(D) are parallel to the picture plane

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -11-

Item 40 refers to the following diagram. 43. Which of the following drawings
represents a truncated prism?

40. The diagram above shows a method of

constructing a

(A) tangent to a circle at a point

(B) tangent at a point on an arc
(C) circle passing through a given
point
(D) circle tangential to two
converging lines

41. Which of the following scales would be

used to produce the smallest drawing of a
given object?

(A) 1:2
(B) 1:1 44. On which of the following planes would
(C) 5:1 the plan of an orthographic projection
(D) 10:1 appear?

(A) Profile
Item 42 refers to the following figure. (B) Vertical
(C) Auxiliary
(D) Horizontal

45. Which of the following class of fire

extinguishers can be used to put out an
electrical fire?
42. The figure above illustrates the start of a
method of construction for drawing views (A) Class A
of (B) Class B
(C) Class C
(A) circles in perspective drawings (D) Class D
(B) circles in isometric drawings
(C) irregular curves in perspective
drawings
(D) irregular curves in orthographic
drawings

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -12-

Item 46 refers to the following diagram. 50. RS is a straight line. A line segment 25 mm
long is marked. Exterior angles of 45° are
marked off at each end of the line segment.
The two angled lines formed are 25 mm
long. If this construction is continued until
a closed figure is formed, the figure
obtained is

(A) a pentagon
(B) a hexagon
(C) an octagon
(D) a nonagon

Item 51 refers to the following drawing.

46. In the drawing above, two arcs are drawn
tangential to two circles of different radii.
What are the lengths of EX and CY
respectively?

(A) 75 and 80
(B) 80 and 75
(C) 80 and 105
(D) 100 and 80 51. The drawing above shows the development
of a

47. The distance between the foci of an ellipse (A) pentagonal box with lid
is 24 mm and the length of its minor axis is (B) hexagonal box with lid
18 mm. The length of its major axis, in (C) pentagonal box without lid
mm, is (D) hexagonal box without lid

(A) 26
(B) 28 Item 52 refers to the following elevations.
(C) 30
(D) 32

48. The tolerance for a shaft 18 mm long is

+0.055 and –0.063. What is the correct
tolerance range?

(A) 17.045 to 18.063

(B) 17.055 to 18.063 52. The elevations shown above are those of a
(C) 18.055 to 17.937
(D) 18.550 to 17.937 (A) square prism
(B) square pyramid
(C) triangular prism
49. Three circles of varying diameters which (D) hexagonal pyramid
touch one another can be drawn if given

(A) their radii and a line

(B) two lines and a point
(C) the position of their centres
(D) three points through which they
pass

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -13-

53. When a plane figure has a linear reduction Item 56 refers to the following drawing.
only, the

(A) proportions are changed

(B) proportions remain the same
(C) dimensions remain the same
(D) dimensions and proportions are
changed

54. Which of the following drawings

represents an escribed circle?
56. In the drawing above, which of the
following is NOT true?
(A)
(A) The line RM is equal to the line
PR.
(B) The line DR can be of any length.
(C) The angle PRM is equal to the
(B) angle RPM.
(D) The angle RMP is equal to the
angle RPM.

(C) 57. A netball court has a length of 30 m. A

line representing this distance on a drawing
measures 30 mm. To what scale ratio is the
line drawn?
(D)
(A) 1:1000
(B) 1: 500
(C) 1: 200
(D) 1: 100
55. Which is the FIRST step that should be
taken if a person receives an electric shock
in a workshop?

(A) Turn off the source.

(B) Activate the fire alarm.
(C) Remove the person to safety.
(D) Cover the person with a safety
blanket.

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
 -14-

Item 58 refers to the following drawing.

58. Which of the following is TRUE of the

drawing above?

(A) The triangle EGH has been

enlarged to a figure which is twice
its area.
(B) The quadrilateral EFGH has been
reduced to a figure having half of
its area.
(C) The triangles EGH and FGH are
equal in area.
(D) The quadrilateral EFGH has been
changed into a triangle of equal
area.

GO ON TO THE NEXT PAGE

01247010/SPEC 2015
59. Which of the following drawings indicates
the correct method of constructing similar
triangles?
Item 60 refers to the following three views.

60. The figures above show three views of a

block. The front elevation, end view and
plan respectively are

(A) I, III and II

(B) II, I and III
(C) II, III and I
(D) III, II and I
- 16 -