UNIT-V

MOMENT DISTRIBUTION METHOD

Distribution and carryover of moments – Stiffness and carry over factors – Analysis of continuous
beams – Plane rigid frames with and without sway – Neylor‟s simplification.
Hardy Cross (1885-1959)
 Moment Distribution is an iterative method of solving an
indeterminate Structure.
 Moment distribution method was first introduced by Hardy Cross in
1932.
 Moment distribution is suitable for analysis of all types of
indeterminate beams and rigid frames.
 It is also called a ‘relaxation method’ and it consists of successive
approximations using a series of cycles, each converging towards
final result.
 It is comparatively easier than slope deflection method. It involves solving number of
simultaneous equations with several unknowns, but in this method does not involve any
simultaneous equations.
 It is very easily remembered and extremely useful for checking computer output of
highly indeterminate structures.
 It is widely used in the analysis of all types of indeterminate beams and rigid frames.
 The moment-distribution method was very popular among engineers.
 It is very simple and is being used even today for preliminary analysis of small structures.
 The primary concept used in this methods are,
 Fixed End Moments
 Relative or Beam Stiffness or Stiffness factor
 Distribution factor
 Carry over moment or Carry over factor

Basic Concepts
 In moment-distribution method, counterclockwise beam end moments are taken as positive.
 The counterclockwise beam end moments produce clockwise moments on the joint.
 Note the sign convention:
Anti-clockwise is positive
Clockwise is negative
Assumptions in moment distribution method
 All the members of the structures are assumed to be fixed and fixed end moments due to
external loads are obtained.
 All the hinged joints are released by applying an equal and opposite moment.
 The joints are allowed to deflect (rotate) one after the other by releasing them successively.
 The unbalanced moment at the joint is shared by the members connected at the joint when
it is released.
 The unbalanced moment at a joint is distributed in to the two spans with their distribution
factor.

 Hardy cross method makes use of the ability of various structural members at a joint to
sustain moments in proportional to their relative stiffness.
Fixed End Moments
 All members of a given frame are initially assumed fixed at both ends.
 The loads acting on these fixed beams produce fixed end moments at the ends.
 FEM are the moments exerted by the supports on the beam ends.
 These (non-existent) moments keep the rotations at the ends of each member zero.
Relative or Beam Stiffness or Stiffness factor
 When a structural member of uniform section is subjected to a moment at one end, then the
moment required so as to rotate that end to produce unit slope is called the stiffness of the
member.
 Stiffness is the member of force required to produce unit deflection.
 It is also the moment required to produce unit rotation at a specified joint in a beam or a
structure. It can be extended to denote the torque needed to produce unit twist.
 It is the moment required to rotate the end while acting on it through a unit rotation,
without translation of the far end being
 Beam is hinged or simply supported at both ends
k = 3 EI / L
 Beam is hinged or simply supported at one end and fixed at other end
k = 4 EI / L
 Stiffness of members in continuous beams and rigid frames
 Stiffness of all intermediate members k = 4 EI / L
 Stiffness of edge members,
 If edge support is fixed k = 4 EI / L
 If edge support is hinged or roller k = 3 EI / L
 Where, E = Young‟s modulus of the beam material
I = Moment of inertia of the beam
L = Beam‟s span length
Distribution factor
 When several members meet at a joint and a moment is applied at the joint to
produce rotation without translation of the members, the moment is distributed
among all the members meeting at that joint proportionate to their stiffness.
 Distribution factor = Relative stiffness / Sum of relative stiffness at the joint
 If there is 3 members,
Distribution factors = k1 / (k1+k2+k3), k2/ (k1+k2+k3), k3/ (k1+k2+k3)
Carry over moment
 Carry over moment: It is defined as the moment induced at the fixed end of the beam by
the action of a moment applied at the other end, which is hinged.
 Carry over moment is the same nature of the applied moment.
Carry over factor (C.O):
 A moment applied at the hinged end B “carries over” to the fixed end „ A‟,
a moment equal to half the amount of applied moment and of the same rotational
sense. C.O =0.5
Problem:
1. Find the distribution factor for the given beam.

A L B L C L D

Joint Member Relative stiffness Sum of Relative stiffness Distribution factor

(4EI / L) / (4EI / L) = 1
A AB 4EI / L 4EI / L

BA 3EI /L (3EI / L) / (7EI / L )= 3/7

B 3EI /L + 4EI / L = 7EI / L
BC 4EI / L (4EI / L) / (7EI / L) = 4/7
CB 4EI / L (4EI / L) / (8EI / L) =4/8
C 4EI / L + 4EI / L =8EI / L
CD 4EI / L (4EI / L) / (8EI / L)= 4/8
D DC 4EI / L 4EI / L (4EI / L)/ (4EI / L) = 1

2. Find the distribution factor for the given beam.

(3I) (I)
A L B L C
Joint Member Relative stiffness Sum of Relative stiffness Distribution factor
A AB 4E (3I ) / L 12EI / L (12EI / L) / (12EI / L) = 1
BA 4E( 3I) /L (12EI / L) / (16EI / L )= 3/4
B 12EI /L + 4EI / L = 16EI / L
BC 4EI / L (4EI / L) / (16EI / L) = 1/4
C CB 4EI / L 4EI / L (4EI / L) / (4EI / L) =1
3. Find the distribution factor for the given beam.
A B C D
L
Joint Member Relative stiffness Sum of Relative Distribution factor
BA 0 (no support) 0
B 3EI / L
BC 3EI / L (3EI / L ) / ( 3EI / L) =1

CB 3EI / L 3EI /L + 4EI / L (3EI / L) / (7EI / L )= 3 / 7

C
CD 4EI / L = 7EI / L (4EI / L) / (7EI / L) = 4 / 7
D DC 4EI / L 4EI / L (4EI / L) / (4EI / L) =1

Flexural Rigidity of Beams:

 The product of young‟s modulus (E) and moment of inertia (I) is called Flexural
Rigidity (EI) of Beams. The unit is N.mm2.
Constant strength beam:
 If the flexural Rigidity (EI) is constant over the uniform section, it is called
Constant strength beam.
Sway:
 Sway is the lateral movement of joints in a portal frame due to the unsymmetrical
dimensions, loads, moments of inertia, end conditions, etc.
What are the situations where in sway will occur in portal frames?
 Eccentric or unsymmetrical loading
 Unsymmetrical geometry
 Different end conditions of the columns
 Non-uniform section of the members
 Unsymmetrical settlement of supports
 A combination of the above
What are symmetric and antisymmetric quantities in structural behaviour?
 When a symmetrical structure is loaded with symmetrical loading, the bending moment and
deflected shape will be symmetrical about the same axis.
 Bending moment and deflection are symmetrical quantities
Steps involved in Moment Distribution Method:
1. Calculate fixed end moments due to applied loads following the same sign convention and
procedure, which was adopted in the slope-deflection method.
2. Calculate relative stiffness.
3. Determine the distribution factors for various members framing into a particular joint.
 4. Distribute the net fixed end moments at the joints to various members by multiplying the
net moment by their respective distribution factors in the first cycle.
5. In the second and subsequent cycles, carry-over moments from the far ends of the same
member (carry-over moment will be half of the distributed moment).
6. Consider this carry-over moment as a fixed end moment and determine the balancing
moment. This procedure is repeated from second cycle onwards till convergence
Advantages of Fixed Ends or Fixed Supports
1. Slope at the ends is zero.
2. Fixed beams are stiffer, stronger and more stable than SSB.
3. In case of fixed beams, fixed end moments will reduce the BM in each section.
4. The maximum defection is reduced.
Problem:
1. Analyse the frame given in figure by moment distribution method and draw the B.M.D &
S.F.D

Step: 1 - Fixed end moment

MFAB = -WL2/12 = - 10×42/12 = -13.33 KNM
F
M BA = WL2/12 = 10×42/12 = -13.33 KNM
F
M BC = - Wab2/L2 = -50×2×32/52 = -36 KNM
F
M CB = Wa2b/L2 = 50×22×3/52 = 24 KNM
Step: 2 - Stiffness
KAB = KBA = 4EI/L = EI
KBC = KCB = 3EI/L = 0.6EI
Step: 3 - Distribution factor
Joint B
DF = K /(K +K ) = 0.63
BA BA BA BC
DF = K /(K +K ) = 0.37
BC BC BA BC

Step: 4 - Moment distribution

B
MEMBER AB CB
BA BC
DF 0 0.67 0.33 0
FEM -13.33 +13.33 -36 +24
BALANCING 0 0 0 -24
CF 0 0 -12 0
M -13.33 +13.33 -48 0
BALANCING 0 21.84 12.83 0
CF 10.92 0 0 0
M-FINAL -2.4 35.17 -35.17 0
Step: 5 - Reactions
Span AB:
RA = 11.81 KN
RB1 = 28.19 KN
Span BC:
RB2 = 37.03 KN
RC = 12.97 KN

2. Analyse the frame given in figure by moment distribution method and draw the
B.M.D&S.F.D

Step: 1 - Fixed end moment

MFAB = -WL2/12 = - 10×42/12 = -13.33 KNM
F
M BA = WL2/12 = 10×42/12 = -13.33 KNM
F
M BC = - WL/8 = -25×4/8 = -12.5 KNM
F
M CB = WL/8 = 25×4/8 = 12.5 KNM
F
M BD = 0
F
M DB = 0

Step: 2 - Stiffness
KAB = KBA = 4EI/L = EI
KBC = KCB = 3EI/L = 0.75EI
KBD = KDB = 4EI/L = EI
Step: 3 - Distribution factor
Joint B
DF = K / (K +K +K ) = 0.36
BA BA BA BC BD
DF = K / (K +K +K ) = 0.28
BC BC BA BC BD
DF = K / (K +K +K ) = 0.36
BD BD BA BC BD
Step: 4 - Moment distribution
B
MEMBER AB DB CB
BA BC BD
DF 0 0.36 0.28 0.36 0
FEM -13.33 +13.33 -12.5 0 0 +12.5
CF 0 0 -6.25 0 0 -12.5
M(initial) -13.33 +13.33 -18.75 0 0 0
BALANCING 0 +1.95 1.52 1.95 0 0
MF 0.98 0 0 0 0.98 0
M-FINAL -12.35 15.28 -17.23 1.95 0.98 0

Step: 5 - Find reactions:

Span AB:
RA = 19.27 KN
RB1 = 20.73 KN
Span BC:
RB2 = 16.32 KN
RC = 8.68 KN
Span BD:
RB3 = -0.73 KN
RD = 0.73 KN
3. The continuous beam ABCD, subjected to the given loads, as shown in Figure below. Assume
that only rotation of joints occurs at B, C and D, and that no support displacements occur at
B, C and D. Due to the applied loads in spans AB, BC and CD, rotations occur at B, C and D
using moment distribution method.
150KN

Step: 1 - Fixed end moments


wl 2 (15)(8)2
M AB  M BA      80 kN.m
12 12
wl (150)(6)
M  M     112.5 kN.m
BC CB
8 8
wl 2 (10)(8)2
M CD  M DC     53.333 kN.m
12 12
Step: 2 - Stiffness Factors (Unmodified Stiffness)
4EI (4)(EI )
K AB  KBA    0.5EI
L 8
4EI (4)(EI )
KBC  KCB    0.667EI
L 6
 4EI  4
K   EI  0.5EI
CD  8  8
4EI
KDC   0.5EI
8
Step: 3 - Distribution Factors

KBA 0.5EI
DFAB    0.0
KBA  K wall 0.5   (wall stiffness )
KBA 0.5EI
DFBA    0.4284
KBA  KBC 0.5EI  0.667EI
DF  KBC 0.667EI  0.5716

K BA  KBC 0.5EI  0.667EI
BC

KCB 0.667EI
DFCB    0.5716
KCB  KCD 0.667EI  0.500EI
DF  KCD 0.500EI  0.4284

K CB  KCD 0.667EI  0.500EI
CD

K
DFDC  KDC  1.00
DC
Step: 4 - Moment Distribution
Joint A B C D
Member AB BA BC CB CD DC
DF 0 0.4284 0.5716 0.64 0.36 1
FEM -80 80 -112.50 112.50 -53.33 53.33

Ist Distribution 13.923 18.577 -37.87 -21.3 -53.33

Carry over Moment 6.962 -18.93 9.289 -26.67 -10.65

2nd Distribution 8.111 10.823 11.122 6.256 10.65

Carry over Moment 4.056 5.561 5.412 5.325 3.128

3rd Distribution -2.382 -3.179 -6.872 -3.865 -3.128

Carry over Moment -1.191 -3.436 -1.59 -1.564 -1.933

4th Distribution 1.472 1.964 2.019 1.135 1.933

Carry over Moment 0.736 1.01 0.982 0.967 0.568

5th Distribution -0.433 -0.577 -1.247 -0.702 -0.568

Carry over Moment
M-FINAL -69.44 100.69 -100.7 -93.748 93.75 0

Step: 5 - Computation of Shear Forces

5. Analyse the beam as shown in figure by moment distribution method and draw the BMD.
Assume EI is constant

Step: 1 - Fixed end moments

MFAB = 0
F
M BA = 0
F
M BC = -WL2/12 = - 20×122/12 = -240 KNM
F
M CB = WL2/12 = - 20×122/12 = 240 KNM
F
M CD = - WL/8 = -250×8/8 = -250 KNM
F
M DC = WL/8 = 250×8/8 = 250 KNM

Step:2 - Distribution factor

Joint Member Relative Stiffness (K) ΣK D.F = (K / ΣK)

BA I / L = (I /12) 0.50
B I/6
BC I / L = (I /12) 0.50
CB I / L = (I /12) 0.40
C 5I / 24
CD I / L = (I /8) 0.60

Step:3 – Moment Distribution

5. Analyze the continuous beam as shown in fig by moment distribution method and
draw BMD & SFD

Step: 1 - Fixed end moments

Step:2 - Distribution factor

Step: 3 - Moment Distribution

Step: 4 – BMD & SFD

6. Analyze the continues beam as shown in figure by moment distribution method and draw the
B.M. diagrams

Support B sinks by 10mm, and take E = 2 x 105 N/mm², I = 1.2 x 10-4 m4

Step: 1 - Fixed end moments

Step:2 - Distribution factor

Step: 3 - Moment Distribution

Step: 4 – BMD
 6. Analysis the frame shown in figure by moment distribution method and draw BMD.
Assume EI is constant

Step: 1 - Fixed end moments

Step:2 - Distribution factor

Step: 3 - Moment Distribution

Step: 4 – BMD
8. Analyze the frame shown in figure by moment distribution method and draw BMD and SFD

Step: 1 - Fixed end moments

Step:2 - Distribution factor

Step: 3 - Moment Distribution