EZ-LIGHT® Touch K50 Series Illuminated

Multipurpose Buttons

Datasheet
General Purpose Multicolor Indicator with Independent Momentary Touch Button Output

For the latest technical information about this product, including specifications, dimensions, and wiring, see
www.bannerengineering.com.

• Rugged, cost-effective, and easy-to-install multicolor indicator with touch

button
• Waterproof IP69K construction for washdown environments
• Three independent colors in one unit—Color 3 overrides Colors 1 and 2, Color
2 overrides Color 1
• Available with PNP and NPN inputs/outputs, depending on model
• Ergonomically designed to eliminate hand, wrist, and arm stresses
associated with repeated switch operation; require no physical force to
operate
• Can be actuated with bare hands or in gloves
• 12 to 30V dc operation

Models
Model 1 I/O Type Output State Color 1 Color 2 Color 3 Connection

K50APTGRYF2Q N.O.
PNP
K50RPTGRYF2Q N.C.
Green Red Yellow Integral 8-pin Euro QD
K50ANTGRYF2Q N.O.
NPN
K50RNTGRYF2Q N.C.

Indicator and Output Behavior

Table 1: PNP Models
Input Actions Touch Button Actions

Input #1: Pin 3 Input #2: Pin 8 Input #3: Pin 4 Output: Pin 1
LED Color Output Type Touch
Green Wire Red Wire Yellow Wire White Wire

Open or -Vdc Open or -Vdc Open or -Vdc Light Off N.O. Not touched PNP Output Off

+V dc Open or -Vdc Open or -Vdc Color #1 On Touched PNP Output On

+V dc +V dc Open or -Vdc Color #2 On N.C. Not touched PNP Output On

+V dc +V dc +V dc Color #3 On Touched PNP Output Off

Open or -Vdc +V dc Open or -Vdc Color #2 On

Open or -Vdc +V dc +V dc Color #3 On

Open or -Vdc Open or -Vdc +V dc Color #3 On

+V dc Open or -Vdc +V dc Color #3 On

1 Integral QD models only are listed. A model with a QD requires a mating cable (see Cordsets on page 3)
• For 8-pin 150 mm (5.9 in) Euro-style PVC pigtail, replace suffix Q with QP in model number (example, K50APTGRYF2QP).
• For 2 m (6.5 ft) cable, omit suffix Q from model number (example, K50APTGRYF2).
P/N 166766 Rev. C 7 November 2013

0 166766 0
 EZ-LIGHT® Touch K50 Series Illuminated Multipurpose Buttons

Table 2: NPN Models

Input Actions Touch Button Actions

Input #1: Pin 3 Input #2: Pin 8 Input #3: Pin 4 Output: Pin 1
LED Color Output Type Touch
Green Wire Red Wire Yellow Wire White Wire

Open or +V dc Open or +V dc Open or +V dc Light Off N.O. Not touched NPN Output Off

-Vdc Open or +V dc Open or +V dc Color #1 On Touched NPN Output On

-Vdc -Vdc Open or +V dc Color #2 On N.C. Not touched NPN Output On

-Vdc -Vdc -Vdc Color #3 On Touched NPN Output Off

Open or +V dc -Vdc Open or +V dc Color #2 On

Open or +V dc -Vdc -Vdc Color #3 On

Open or +V dc Open or +V dc -Vdc Color #3 On

-Vdc Open or +V dc -Vdc Color #3 On

Dimensions

Wiring Diagram

NPN (Sinking) Output Models PNP (Sourcing) Output Models Wiring Key Pinout

2 2
+ +
7
12-30V dc
–
7
12-30V dc
–
1 = White
1 1 2 = Brown
Load Load
3 = Green 2
3 3 3
C1 C1
4 = Yellow 1 4
8 8
C2 C2 5 = Gray 7
5
4 4 6 = Pink 6
C3 C3 8
5
N/C
5
N/C 7 = Blue
6 6 8 = Red
N/C N/C

2 www.bannerengineering.com - tel: 763-544-3164 P/N 166766 Rev. C

 EZ-LIGHT® Touch K50 Series Illuminated Multipurpose Buttons

Specifications
Supply Voltage Environmental Rating
12 to 30 V dc IEC IP67, IP69K per DIN 40050-9. Cabled models also meet IP69K if
Supply Current the cable and cable entrance are protected from high-pressure spray.
< 75 mA max current at 12 V dc (exclusive of load) Operating Conditions
< 50 mA max current at 30 V dc (exclusive of load) Temperature: -40 °C to +50 °C (-40 °F to +122 °F)
Supply Protection Circuitry Humidity: 90% at 50 °C max. relative humidity (non-condensing)
Protected against reverse polarity and transient voltages Storage
Output Rating -40 °C to +70 °C (-40 °F to +158 °F)
Maximum Load: 150 mA Construction
ON-state saturation voltage: < 2V at 10 mA dc; < 2.5V at 150 Housing: polycarbonate
mA dc Translucent dome: polycarbonate
OFF-state leakage current <10 µA at 30 V dc Mounting Nut: PBT
Output Response Time Mounting
50 milliseconds On and Off M30 x 1.5 Threaded base Max torque 4.5 Nm (40in lb f)
Power-Up Output Delay Time Vibration and Mechanical Shock
300 milliseconds All models meet Mil. Std. 202F requirements method 201A (vibration:
Connections 10 to 60 Hz max., double amplitude 0.06 in. maximum acceleration
10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave.
8-pin integral Euro-style QD, 2 m (6.5 ft) PVC integral cable, or 8-
pin 150 mm (5.9 in) Euro-style PVC pigtail QD Certifications
Indicators
Color 1: Green
Color 2: Red
Color 3: Yellow

Accessories

Cordsets
8-Pin Threaded M12/Euro-Style Cordsets with Open-Shield

Model Length Style Dimensions Pinout

MQDC2S-806 1.83 m (6 ft)

MQDC2S-815 4.57 m (15 ft) 44 Typ.

2
3
MQDC2S-830 9.14 m (30 ft) 1 4
Straight
7
MQDC2S-850 15.2 m (50 ft) M12 x 1
5
6
8
ø 14.5

1 = White
MQDC2S-806RA 1.83 m (6 ft) 2 = Brown
3 = Green
MQDC2S-815RA 4.57 m (15 ft) 32 Typ.
4 = Yellow
[1.26"]
5 = Gray
MQDC2S-830RA 9.14 m (30 ft) 6 = Pink
30 Typ. 7 = Blue
MQDC2S-850RA 15.2 m (50 ft) 8 = Red
Right-Angle [1.18"]

M12 x 1
ø 14.5 [0.57"]

P/N 166766 Rev. C www.bannerengineering.com - tel: 763-544-3164 3

 EZ-LIGHT® Touch K50 Series Illuminated Multipurpose Buttons

Brackets

SMB30A 45 SMB30FA
• Right-angle bracket with • Swivel bracket with tilt and 83.2
curved slot for versatile C pan movement for precise
orientation 61 adjustment
• Clearance for M6 (¼ in) B • Mounting hole for 30 mm
hardware sensor
A 36.3 B 68.9
• Mounting hole for 30 mm • 12-ga. 304 stainless steel
sensor 69 • Easy sensor mounting to A
• 12-ga. stainless steel extrude rail T-slot
• Metric and inch size bolt
Hole center spacing: A to B=40 available
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 -
1.5 x 50
Hole size: B= ø 30.1

SMB30FVK SMB30MM
70 57
• V-clamp, flat bracket and 46
• 12-ga. stainless steel bracket
fasteners for mounting to 118 with curved mounting slots
pipe or extensions for versatile orientation C
• Clamp accommodates 28 A • Clearance for M6 (¼ in) 57
B
mm dia. tubing or 1 in. hardware
square extrusions • Mounting hole for 30 mm
A
• 30 mm hole for mounting sensor
sensors
Hole center spacing: A = 51, A to B = 25.4
Hole size: A= ø 31 Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1

67
SMB30RAVK SMB30SC
A
• V-clamp, right-angle bracket • Swivel bracket with 30 mm B
and fasteners for mounting mounting hole for sensor
sensors to pipe or extrusion 46 • Black reinforced 58
• Clamp accommodates 28 thermoplastic polyester
mm dia. tubing or 1 in. • Stainless steel mounting and
square extrusions swivel locking hardware
57 90 29
• 30 mm hole for mounting included A
sensors
Hole center spacing: A=ø 50.8
Hole size: A = ø 30.5 Hole size: A=ø 7.0, B=ø 30.0

45
SMBAMS30P SMBAMS30RA
45
• Flat SMBAMS series bracket C • Right-angle SMBAMS series
bracket C
• 30 mm hole for mounting
sensors 93
A • 30 mm hole for mounting 53 A
• Articulation slots for 90°+ sensors
B B
rotation • Articulation slots for 90°+
• 12-ga. 300 series stainless rotation
48
steel • 12-ga. (2.6 mm) cold-rolled
steel
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0 Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0

4 www.bannerengineering.com - tel: 763-544-3164 P/N 166766 Rev. C

 EZ-LIGHT® Touch K50 Series Illuminated Multipurpose Buttons

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp.

www.bannerengineering.com - tel: 763-544-3164