Speed Control of Three Phase Induction Motor

The Three-Phase Induction motor is one of the frequently used electric motors due
to its simplicity, reliability, and efficiency in industrial applications. Such motors are
mostly applied in industries where a constant speed and high torque are required—
pumps, compressors, conveyors, and machine tools. However, there is the need to
vary motor speed in a number of cases where specific operational requirements are
to be met, or for improved energy efficiency.
Three-phase induction motor speed control may be done through many methods that
each have their own merits and demerits. These methods are required for
applications where motor speed should be adjusted to match load conditions for
better performance, for saving energy, or in general for running a motor at different
speeds. A proper understanding of these techniques of speed control would be
important in the optimal operation of motors in industries that increase productivity
and reduce operational cost.
This paper therefore discusses the basics of three-phase induction motor principles
in speed control, both conventional and modern methods. By the end of this
discussion, you will gain an overall understanding of the working of these methods
and their application in real-world situations.

Speed Control of Three Phase Induction Motor

The speed of a three-phase induction motor mainly depends on the supply frequency
and the number of poles of the motor and is given by the equation:
Speed=120×Frequency / Number of Poles Speed

As the number of poles is constant for a given motor design, change of supply
frequency or changing the slip (difference between synchronous speed and actual
rotor speed) becomes the two methods for speed control and are thus broadly
classified into the...
 Stator Voltage Control
 Frequency Control
 Rotor Resistance Control
 Pole Changing
 Slip Power Recovery

Methods of Speed Control of Three Phase Induction Motor

Stator Voltage Control
The supply voltage variation method is one way of going about it, where the supply
voltage to the stator is varied. Since the torque of an induction motor is proportional
to the square of the applied voltage, reduction in voltage will reduce the torque and
thereby produce a lower speed. Although very simple, this method is quite inefficient
because the reduction of the voltage also increases slip, which in turn leads to higher
losses and thus lowered efficiency.

Stator Control
Speed Equation
Slip S is given by:
S = Ns−N / Ns

Where Ns is the synchronous speed.

Frequency Control
Frequency control is one of the most effective ways of controlling the speed of an
induction motor. The variation of the frequency of the supply voltage directly
controls the synchronous speed of the motor. This way of control is more
traditionally realized through the method of the Variable Frequency Drives (VFD),
which have a very flexible application to the control of motor speed and torque, the
VFD changes both the frequency of the motor driving signal and the applied voltage,
maintaining a V/f ratio to keep the current from rising too high.

Frequency Control

Synchronous Speed Ns is given by:

Ns = 120 × f / P

V/f Ratio
 To avoid magnetic saturation and maintain motor performance, the voltage-to-
frequency ratio (V / f) is kept constant:
V / f = constant

Rotor Resistance Control

More resistors are placed in series with the rotor windings in wound rotor induction
motors. The resistance in the rotor circuit may be varied, thus varying the slip and,
hence, the speed of the motor.
Additional resistance can be added to the rotor circuit of a wound rotor induction
motor. With this method, increasing the rotor resistance increases slip and thereby
reduces the speed of the motor. This allows fine-tuning of the speed, although it is
highly inefficient because of power losses in the resistors. It is typically applied only
in applications that require tight speed control at very low speeds.

Rotor Resistance Control

Speed Equation
 Slip ss with external resistance R2′ added:
S = (R2 + R2′ ) / ( R2+R2′ ) 2 + (X2)2
Pole Changing
The synchronous motor's speed may be altered by simply changing the number of
stator poles. To do this, the connections of the stator winding should then be
reorganized.
The method achieves the same objective through the variation of the number of poles
in the stator winding. These connections can be rearranged so that the stator
windings are in a configuration that enables the motor to operate with a different
number of poles, which corresponds to a different motor speed. This type works well
for applications that require only discrete levels of speeds.
Connection for different Poles
Key Equation
 Synchronous Speed Ns for different poles:
Ns = 120 × f / P

Slip Power Recovery

It works for slip ring induction motors. The slip power is recovered from the rotor
circuit and fed either back to the power source or employed to control speed through
driving auxiliary machinery. This is used in slip ring motors, where the slip power
is regained from the rotor and fed back to the supply, or can be utilized to drive other
machines. This type of method, although efficient and providing a good range of
speed control, is complex and expensive
Slip Power Recovery
Key Equation
 The power recovered is proportional to slip:
Pslip = S × Pinput

Speed Equation
Speed NN with slip power recovery
N = Ns ( 1−s )

Characteristics of Speed Control of Three Phase Induction

Motor
Speed control is a process in which the operational features of a three-phase
induction motor are altered in adjusting it to have characteristics meeting specific
performance requirements. Knowing the characteristics is important, since with
knowledge comes the ability to select the proper speed control method and ensure
that motor performance is optimized.
Torque-Speed Characteristics
 Frequency Control: This method through variable frequency drives (VFD)
usually comes out with an almost linear characteristic between torque and speed.
The motor can give a constant torque developed over a wide range of speeds,
which is very important in some applications where fine regulation of speed is
needed.
 Stator Voltage Control: This method results in the nonlinearity of the torque-
speed characteristics, where the torque greatly decreases at low speeds. This is
far from the best condition for most variable-torque applications.
 Rotor Resistance Control: As the rotor resistance is increased, a steeper torque-
speed curve is obtained that provides a large variation in speed, especially at low
speeds. But this results in losing efficiency and higher heat generation.

Torque Speed Characteristics

Advantages of Speed Control of Three Phase Induction

Motor
 Energy Efficiency: This aids in energy savings, as the motor can be run at the
most efficient speed possible under a particular load. Precise speed control allows
for improved process control, especially in industries such as manufacturing,
which require a given speed for different stages of operation.
 Prolonged Equipment Life: Controlled acceleration and deceleration minimize
mechanical shock to both the motor and driven equipment, therefore reducing
wear and tear and extending operation life.
 Increased Operational Flexibility: Adjustable speed gives a facility for
controlling the speed of motors according to specific needs in different
applications, which in turn increases flexibility and productivity.
 Reduced Maintenance Costs: Since motor and mechanical systems are under
less stress in controlled speeds, wear is minimized; hence, less maintenance is
needed, and this means cheaper maintenance costs in the long run.

Disadvantages of Speed Control of Three Phase Induction

Motor
 High Initial Cost: The advanced system of speed control, especially employing
the Variable Frequency Drive (VFD) or the slip power recovery system, is
expensive to apply.
 Complexity: Installation, configuration, and maintenance of a speed control
system are complex and require specialized knowledge and skills that may not
be available at all places.
 Harmonic Distortion: Devices such as VFDs create harmonic distortions in the
power supply and may, in all probability, affect the operation of other connected
equipment in the same power network.
 Efficiency Loss at Lower Speeds: This can be better explained by stating that
some methods of control—like stator voltage or rotor resistance methods—give
a loss of efficiency at lower speeds because of the associated increased slip
and power losses.

Applications of Speed Control of Three Phase Induction

Motor
 HVAC Systems: VFDs control fan and pump speeds for energy efficiency.
 Conveyor Systems: Speed control allows for precise material handling.
 Cranes and Hoists: Rotor resistance control is often used for smooth speed
regulation under varying loads.
 Textile Mills: Pole changing methods are used to adjust the speed of looms and
other machinery.
 Pumps: Speed control helps in maintaining the desired flow rate or pressure.

Solved Examples on Speed Control of Three Phase

Induction Motor
Example 1
A 3-phase induction motor is connected to a 50 Hz supply. It has four poles.
Determine the synchronous speed.
Solution
Synchronous Speed = 120 × 50 / 4 = 1500 RPM

Example 2
If a VFD controls the motor in Example 1 and the frequency is reduced to 40 Hz,
what will be the new speed then?
Solution
New Speed = 120 × 40 / 4 = 1200 RPM

Conclusion
Speed control of three-phase induction motors plays an increasingly important
application with modern industrial processes, both in efficient operation and benefit
in process optimization in energy-saving applications, the choice of methods for the
speed control of three-phase induction motors could be made on the application
requirements, cost factors, or range of desired control. Though advanced methods
such as frequency control give excellent performance, simpler methods may still be
applicable to less demanding applications.