Western Bicutan National High School

EP Housing Phase 1, Western Bicutan Taguig City

THIRD QUARTER EXAMINATION
Technology and Livelihood Education 9 - Computer System Servicing 9
(Grade 9 - 2,6,7,8,9,10,12,14,17,20)

Name: ______________________________________ Score:__________________

Year & Section: ______________________________ Date: __________________

MULTIPLE CHOICE
Directions: Read and analyze the questions carefully. Select the best answer that corresponds to the
given question. Write only the letter on the space provided.

1. What cable is used with wired networks?

a. Ethernet cable b. Molex c. Power cable d. SATA
2. Switches belong to what part of a circuit?
a. Connecting b. Controlling c. Protecting d. Source
3. A bulb is an example of what part of a circuit?
a. Connecting b. Consuming c. Protecting d. Source
4. Which of the following best describe electricity?
a. It is the pathway where current flow.
b. It is the flow of electron or electric current.
c. It is the amount of pulling force that makes the electron flow
d. It is the opposition to the flow of current and measured in ohms.
5. Which circuit splits into two or more branches?
a. Closed Circuit b. Open Circuit c. Parallel Circuit d. Series Circuit
6. Which of the following is the best example of an electrical insulator?
a. Aluminum b. Copper c. Metal d. Rubber
______7. What is resistance?
a. Electromagnetic Force
b. Flow of Current
c. How much electricity is prevented from flowing through a given point
d. How much electricity flows through a given point
8. Which is true about the illustration below?
a. The switch is “OPEN”, the current can’t flow into the circuit and the bulb is
“OFF”.
b. The switch is “CLOSED”, the current can’t flow into the circuit and the
bulb is “ON”
c. The switch is “OPEN”, the current can flow into the circuit and the bulb is
“ON”
d. The switch is “CLOSED”, the current can flow into the circuit and the bulb
is “OFF”

9. In a circuit when an electric current flow in a continuous path, it is called?

a. Closed Circuit b. Open Circuit c. Parallel Circuit d. Series Circuit
_ 10. Which of the following is NOT a requirement for electrical connections?
a. Right terminal fitting b. Right tool c. Right time d. Right wire
__11. What safety device is used to protect an electrical circuit from the effect of excessive
current?
a. Cable b. Fuse c. Switch d. Wire
__12. Can you list examples of tools and materials in making a network cable?
a. Crimping tools, multi-tester, RJ11 and UTP cable.
b. Crimping tool, LAN tester, RJ 45 and UTP cable.
c. LAN tester, RJ11, RJ34 and wire stripper.
d. LAN tester, screwdriver, RJ11 and UTP cable.
______13. What tool is used in joining two or more metal conductors with the support of soldering lead
melted around it.
a. Crimping Tool b. Multi tester c. Soldering tool d. Wire Cutter
______14. Which of the following is define as the opposition to the flow of current and measured in
ohms (Ω)?
a. Current b. Electricity c. Resistance d. Voltage
______15. What component of a circuit is commonly represented by a cell or a battery?
a. Fuse b. Load c. Supply d. Switch
______16. What part of a simple circuit controls the flow of current from the source to the consuming
devices?
a. Connecting b. Controlling c. Protecting d. Source
 ____17. In making a network cable, how could you determine that the rj45 is the right
position?
a. If the first pin of RJ 45 is facing in left side
b. If the first pin of RJ45 is facing in right side
c. If the last pin of RJ45 is in left side
d. the opening of RJ45 is away from the user
___18. In soldering, what is the proper way of melting the iron?
a. Cut the hot tip of the soldering gun to the iron.
b. Push the hot tip of the soldering gun to the iron.
c. Pour the hot tip of the soldering gun to the iron.
d. Touch the hot tip of the soldering gun to the iron.
___19. Which of the following electronic components is NOT used in wire termination?
a. Connector b. Switch c. Terminal d. Transistor
___20. Which of the following electrical quantity is considered as electrical path?
a. Battery b. LED c. Switch d. Wire/cable
_______21. What is the first thing that you must do before measuring resistance?
a. Connect the test pins to measured resistance under test.
b. Set the pointer of the meter to zero (0) Ω.
c. Turn the range selector knob to an appropriate Ω range.
d. Read the Ω scale where the meter pointer rest.
______22. What diagram drawn by using symbols which represents electrical components?
a. Charges Diagram c. Electric Diagram
b. Schematic Diagram d. Picture Diagram
___ __23. After crimping the cable, you need to test the cable in order to know the correct
arrangement of cables that will be used in networking. What tool would you use?
a. LAN Tester b. Multi Tester c. UTP Tester d. Volt Ohmmeter
__24. What are the two types of electronic components?
a. Active and Inactive Components c. Direct and Indirect Components
b. Active and Passive Components d. Inactive and Passive Components
__25.Which of the following is define as the opposition to the flow of current and measured
in ohms (Ω)?
a. current b. electricity c. resistance d. voltage
______26. What testing method is an organized examination or formal evaluation exercise?
a. Automated Testing c. Inspecting Testing
b. Debugging d. Prototyping
______27. What might happen of the applied voltage is incorrect?
a. Finish task on time c. Lead to a successful task
b. Lead to damage d. None of the above
___ __28. Albert found a capacitor at home to replace the faulty one, what type of test will be used to
identify if it is busted/ broken or still working?
a. continuity test b. diagnostic test c. performance test d. voltage test
__29. Which method is used to detect losses or increase in voltage?
a. continuity test b. diagnostic test c. performance test d. voltage test
__30. What test equipment is a combination of Voltmeter, Ammeter and Ohmmeter used to
measure different parameters of an electronic circuit like current, voltage?
a. LAN tester b. Multi tester c. Oscilloscope d. Signal generator
__31. Which testing method is done to detect faults and problems?
a. continuity test b. diagnostic test c. performance test d. voltage test
___ __32. In testing electronic component, which of the following steps come first?
a. Determine criteria for testing electronics components.
b. Evaluate the testing process.
c. Plan an approach for components testing.
d. Test components
__33. What process is used to control the functionality of any electronic component to
ensure whether a component is defective or not?
a. evaluating b. planning c. preparing d. testing
___ __34. Kevin is diagnosing a computer. He noticed that there is no flow of electricity in the entire
system even if the computer is turning on. What would be the best tool he needs to troubleshoot his
computer?
a. Crimping Tool b. LAN Tester c. Loopback adapter d. Multi tester
_____35. . What will happen to the device if connectors are removed while the power is still on?
a. Automatic restart c. Nothing will happen
b. Malfunction of device d. None of the above
__36. The tape in together method in wire connection uses _______ to connect two wires together.
a. Double sided tape c. Masking tape
b. Electrical Tape d. Plastic tape
 ______37. You are task to make a circuit in turning on the computer system. Which of the following
preparations should be done first?
a. Check the voltage of electrical sources. c. Study schematic symbols.
b. Get all tools and materials needed ready. d. Test the circuit
______38. What is the first thing that you must do before measuring resistance?
a. Connect the test pins to measured resistance under test.
b. Set the pointer of the meter to zero (0) Ω.
c. Turn the range selector knob to an appropriate Ω range.
d. Read the Ω scale where the meter pointer rest.
______39. What does open pointer when testing resistor indicates?
a. has no deflection in any setting?
b. turn to zero in any setting.
c. higher than the allowed resistor.
d. lower than the allowed resistance.
__40. How do you connect the Multimeter to measure current?
a. Connect the meter in series with the load.
b. Connect the meter in parallel with the load.
c. Connect the meter in series with the switch.
d. Connect the meter in parallel with the switch
__41. What process is performed in creating ethernet cable?
a. soldering b. riveting c. clamping d. crimping
__42. Which of the following step is performed, when measuring unpredicted voltage value?
a. Select the minimum range. c. Select the maximum range.
b. Select 250 voltage range. d. Select 50 voltage range.
(For item number 43 – 50) Study the diagram below and answer the questions.

__43. How many Loads are there in the diagram?

a. 2 b. 3 c. 4 d. 5
__44. How many lamps are there in the diagram?
a. 2 b. 3 c. 4 d. 5
__45. Name all the Loads in the diagram.
a. Bulb and Fan b. Fridge and Lamp c. Fan and fridge d. Lamp, Fan and Fridge
__46. How many switches are there?
a. 1 b. 2 c. 3 d. 4
__47. What type of diagram does the image portray?
a. Pictorial b. Schematic c. technical d. flowchart
__48. Which component in the diagram represented the supply or source?
a. MCB b. lamp c. circuit breaker d. socket
__49. Which component in the diagram protect an electrical circuit from damage caused by
overcurrent/overload or short circuit?
a. fridge b. lamp c. socket d. circuit breaker
_50. Does the diagram show a complete circuit? Why?
a. No, there is no flow of electric charges present.
b. No, the components are incomplete.
c. Yes, there is source of current and it consist of components needed in a circuit.
d. None of the above.
 KEY TO CORRECTION
(Sections: 2,6,7,8,9,10,12,14,17,20)
CSS9 3RD QUARTER EXAM
1. A 26. C
2. B 27. B
3. B 28. B
4. B 29. D
5. C 30. B
6. D 31. B
7. C 32. A
8. A 33. D
9. A 34. D
10.C 35. B
11. B 36. B
12. B 37. B
13. C 38. B
14. C 39. A
15. C 40. A/C
16. B 41. D
17. A 42. C
18. D 43. C
19. D 44. A
20. D 45. D
21. B 46. B
22. B 47. A
23. A 48. D
24. B 49. D
25. C 50. C