IPhone 7 Boot Circuit

Boot Circuit mainly starts with PP_VDD_MAIN and boot triggering.(

PP_VDD_MAIN और र .. )

Step 1: Power Supply of Battery is is outputted to Power Mosfet Q2101and charge

control IC U2101 Charging IC.( र र र Q2101and
IC U2101 IC )

Step 2: If the voltage from the battery meets requirements of the boot process (3V
to 4.2V). charging IC U2101 will send a low voltage to Q2101, so the Gate of
Q2101 is completed.( र (3V 4.2V) र
र IC U2101 र र Q2101 ए ए , ए Q2101
र )
Step 3: Now, PP_BATT_VCC will then be outputted by way of Q2101and converted
into PP_VDD_MAIN afterwards.( अ , PP_BATT_VCC PP_VDD_MAIN
र Q2101and ए )

Step 4: Voltage will be outputted from PP_BATT_VCC to U2101(

PP_BATT_VCC U2101 ए )

will also be converted into PP_VDD_MAIN after internal process of U2101 and then the voltage is
outputted from Pin A2 of U2101.( U2101 र PP_VDD_MAIN र
ए और र U2101 A2 )
Step 4: The Two Rails of the main power suppply will then be integrated and outputted to PMU.(
र रए ए और ए ए )

NOTE: U2301 is boost IC, we can say assistant to VDD_MAIN line.. Both generate same voltage 4.2V..(
U2301 र , VDD_MAIN ए .. ए
4.2V र )
If VDD_MAIN is pulling down from 4.2 to 3.4V then VDD_BOOST will handle it and boost
VDD_MAIN( VDD_MAIN 4.2 3.4V र VDD_BOOST और
VDD_MAIN )

Step 5: AFter PMU receiving the voltage, PMU will send a boost enable signal to
Voltage converting IC U2301(Boost IC( र PMU , PMU IC
U2301 (Boost IC) र र )

Step 6: U2301(Boost IC) will then form a rail of Boost Circuit with L2301( U2301 ( ) L2301
ए र ए )
Step 7: The Boost Circuit converts VDD_MAIN into a 3.4V VDD_BOOST voltage
and then output it to PMU, if the VDD_MAIN received is between 3.4V and 4.3V,
then there will be no Boost Process. U2301 will output VDD_MAIN directly as
VDD_BOOST to PMU.( VDD_MAIN 3.4V VDD_BOOST
र र और र PMU र , अ र VDD_MAIN 3.4V
और 4.3V , Boost U2301 VDD_MAIN
VDD_BOOST PMU र )
Step 8: With Main Power Supply and VDD_BOOST fulfilled, PMU will generate
PP1V8_ALWAYS internally and then, PP1V8_ALWAYS will be outputted to Pin 13 of
J4504 (Power on Connector). With the Power Button being pressed, first it will
activate 32.768K Clock.( और VDD_BOOST र , PMU
र PP1V8_ALWAYS र और र, PP1V8_ALWAYS J4504
( र र) 13 ए र ए ,
32.768K र )
Signal Name:

BUTTON_POWER_KEY_CONN_L

Step 9: When we press the Power Button PP1V8_ALWAYS will be pulled down and
become Trigger signal, with the boot trigger signal fulfilled PMU will generate 16
rails of Power Supply voltage with the help of inner buck circuit..( र
PP1V8_ALWAYS ए और र ए , र
र PMU, र र 16 र
र )

Among them 14 rails of voltage for working of CPU..( र

ए 14 र )

1. PP_CPU_VAR 0.625V to 1.06V

2. PP_GPU_VAR 0.675V to 0.92V

3. PP_SOC_VAR 0.67V to 0.92v

4. PP1V8_SDRAM

5. PP1V8

6. PP1V1_SDRAM
7. PP1V1

8. PP0V9_SOC_FIXED 0.9V

9. PP_CPU_SRAM 0.8V tO 1.06v

10. PP_GPU_SRAM 0.82V to 0.92v

11. PP0V8_AOP

12. PP1V2_SOC

13. PP1V2_REF

14. PP3V3_USB

14 Power Supplies to CPU

Step 10: 3 Power rails of voltage for working of the NAND FLASH U1701 chip
..( रण 10: U1701 ए 3 र र )
Nand Voltages

1.PP1V8

2.PP0V9 NAND

3.PP3VO NAND

After power supplies outputted from PMU, CPU starts to work and extracts data
needed for the boot process from Nand Flash Chip and Logic EEPROM IC.

( ए , र र और
और ए )

Step 11: Once CPU receives the 14 voltages then, CPU will get the 24MHZ system
clock started.( ए र 14 र , 24MHZ
र )
Step 12: Now, PMU will then output a reset signal to CPU ( अ , ए एए र
र )

with the reset signal completed, CPU will extract needed Data for the Boot Process from Nand Flash
Chip and Logic EEPROM iC, then CPU will get these key components into Power On Self Process to get
the booting files imported and drivers. So the components and applications needed for the Boot
Process to be awaken (through I2C lines for each circuit)

(र र , CPU ए र और EEPROM iC
, र CPU र और र ए ण र
ऑ र ए ए और अ ए
( ए I2C ))
Step 13. Now, CPU will manage PMU through SPI bus, so that the PMU will get the Phone Power
Supplied continuously.. ( अ , CPU SPI PMU र , PMU र
र )

This is whole Boot Process of Iphone 7..

End of Iphone 7 Boot Circuit...